Trimmer
GL570/GL580
Instruction Manual
Safety instructions
Congratulations!
Your purchase of this Black & Decker Reflex® trimmer
assures you of years of problem free trimming. The
Reflex® not only trim ’n’ edges your lawn, it also has
a unique totally automatic line feed system. You do
nothing - the Reflex® system means non-stop
trimming; by the use of a simple mechanism it
senses when the line has worn and, when needed,
automatically feeds out line to its optimum cutting
length. You just switch the unit on and trim.
Read all of this manual carefully, observing all
the recommended safety instructions before,
during and after using your machine. Maintain
your machine in good working order.
Familiarise yourself with the controls on your
machine before attempting to operate it, but
above all, be sure you know how to stop
your machine in an emergency.
Retain this manual and all other literature
supplied with your machine for future reference.
Description
Electrical connection
Following is a list of the parts that will be mentioned
in this instruction leaflet and are shown in the
appropriate diagrams:
•
Your machine is designed for use on
AC (mains) electrical supplies only. Do
not attempt to use on any other supply.
Body (1)
•
•
Plug your machine into a power point,
never in a light socket.
1
Secondary handle (2)
Do not leave your machine
unattended whilst it is connected to
the electrical supply.
Supply cord restraint (3)
Locking ring (4)
Cutting line (5)
•
Always switch off and remove the
plug from the mains before cleaning,
inspecting or adjusting any part of the
trimmer, or if the supply cable has
become damaged or entangled.
Guard (6)
!
Line trimming blade (7)
Edge guide (9)
Cable storage hooks (11)
Hanging hole (18)
Power inlet or supply cord (19)
Switch handle (20)
Trigger switch (21)
Arrow (24)
Power supply cord
•
•
•
The power supply cord should be
regularly inspected for signs of damage or
ageing and only used if in good condition.
Always keep the power supply cord
away from the cutting line (5), be aware
of its position at all times.
Skid (25)
Never carry your machine by the cord or
jerk the cord to separate the connectors.
Keep the cord away from heat, oils and
sharp edges.
Pedal (26)
Button (27)
Guard retaining lugs (10)
•
Have damaged cords replaced
completely by your nearest Black & Decker
service centre. Do not attempt to do this
yourself as the switch handle is not
customer serviceable.
2
Guard screw (22)
Guard screw hole (23)
Spool cover (8)
4
Spool housing (12)
Cutting line
Spool cover tab (13)
•
Take care against injury from line trimming
Eyelet (15)
Spool (17)
5
blade (7) during unpacking and assembly
and any excess line which may be cut off
when the trimmer is first operated.
Arrow (16)
•
The cutting line (5) will continue to run for
a short time after releasing the switch
lever. Under no circumstances should
6
Lever (14)
7
2
Warning! Never connect Live or Neutral
•
•
In transit, your trimmer is packed in
‘Edging’ mode, if you want to ‘Trim’ refer
to the section ‘How to convert between
the trimming and edging mode’.
wires to Earth pin marked ‘E’ or
.
!
Fuse replacement (UK only)
Your machine is supplied with cable fitted
with a non-wireable plug.
In transit, the end of the cutting line (5) is
taped to the side of the spool cover (8).
Please discard the tape to release the
length of line. There should be a
minimum of 9cm (3.5") of cutting line
protruding from the spool housing (12)
before using your trimmer.
•
The plug is fitted with a 5 amp fuse
which is the recommended fuse for
your machine.
•
•
Only use replacement fuses which are
approved to BS1362.
When changing the fuse in your plug,
always ensure the fuse cover is refitted.
If the fuse cover is missing or damaged
do not use the plug.
Note: When your machine is operated for
the first time any excess line will be cut off by
the line trimming blade (7) housed in the
guard. This is also the case for any
subsequent line adjustment. Because line
cut off by the blade in the guard may be
ejected, it is important that the amount of
excess line is kept to a minimum. Where an
excessive amount of line is pulled out, the
line should be cut back to the outside of the
guard before switching on your trimmer. Cut
the line off on the trimmer blade by hand.
Note: Fuses do not give personal protection
against electric shock. The recommended
Black & Decker RCD is available from your
nearest Black & Decker service centre.
Increased safety can be obtained by having
a qualified electrician install a high sensitivity
(30mA) circuit breaker in the house wiring.
If you do not have such a circuit breaker
installed, or you do not wish to have one
installed, then we strongly recommend that
the electrical power to the machine be
supplied through a high sensitivity residual
current device (RCD). The RCD is designed
to provide a high degree of personal
•
Always ensure that the spool cover is
secure before and after use.
How to use your trimmer (Fig. A - K)
In order to get the most from your trimmer please be
sure to follow the techniques shown. Do not be
impatient; you will obtain the best results by
experience and by following these simple rules.
protection against harmful electric current
should fault conditions occur.
Warning! The use of an RCD or other circuit
breaker unit does not release the operator of
the machine from the safety instructions and
safe working practices given in this manual.
Do not use your trimmer without
its guard.
!
A
B
Do not cut wet grass; best results are
achieved when the grass is dry.
Trimming
Extension cables and cordsets
You can use up to 100 feet (30 metres) extension
cord without undue loss of power. Extension cables
and cordsets should comply with national regulations.
•
•
•
To switch on your trimmer, squeeze the
trigger switch (21).
To switch the unit off, release the
trigger switch.
To carry the trimmer when not in use,
it is preferred that you use the secondary
handle (2).
Preparing the trimmer for use (Fig. 2)
•
Take the trimmer and the guard (6) out of
the box.
2
Cut at an angle and with the tip of the
cutting line (5).
•
Remove the guard screw (22) which is
located on the base of the trimmer body
(1) (Fig. 2.1).
C
D
Swing the trimmer gently from side to side.
•
•
Place the guard into the channel on the
trimmer body.
Do not overload the trimmer. It operates best
at high speeds.
E
Push the guard fully home until the guard
is flush with the body (Fig. 2.2).
On long grass, start at the top.
F
•
•
Replace the guard screw (Fig. 2.3).
Take small cuts.
If correctly assembled, the guard will now
be secured to your trimmer.
G
H
Use the edge of the guard (6) to keep the
trimmer away from hard surfaces and
delicate items.
4
Edging
ENGLISH
Best results are achieved on edges greater
than 50mm deep.
I
Note: Your trimmer is a maintenance tool for
trimming overhanging grass and should not
be used to create edges. Edges can be
created using an edging spade.
To adjust the height of your trimmer:
3
Unlock
With the skid (25) on the grass edge and the
edge guide (9) hooked over the edge, pull
the unit along while keeping the edge guide
in contact with the lawn edge.
•
With the trimmer switched off and the
edge guide (9) resting on the ground,
place one hand on the switch handle
(20). Using your other hand, turn the
locking ring (4) anti-clockwise,
J
K
A closer cut can be achieved by angling
the trimmer.
approximately quarter of a turn (Fig. 3.1).
If your trimmer is suitable for use with a
‘Detachable’ extension cord, loop a length of
cord through the cord restraint (3) to avoid
the plug and socket coming apart
Adjust
While keeping hold of the switch handle,
•
grasp the trimmer body (1) with your other
hand and raise/lower the switch handle
to your desired operating position (Fig. 3.4).
accidentally if the cord is pulled.
Lock
While still holding the switch handle,
How to convert between the
•
trimming and edging mode (Fig. 3)
tighten the locking ring clockwise, using
the other hand. Only light finger pressure
is required to secure it (Fig. 3.3).
In addition to conventional trimming
(Fig. D), your trimmer can be used to trim
overhanging grass along lawn edges and
flower beds (Fig. J).
How to alter the position of the
secondary handle (Fig. L)
To convert your trimmer between the
3
trimming and edging mode:
Your trimmer has an adjustable secondary
handle to allow you to position it for maximum
comfort and balance. It can be folded flat for
compact storage.
Unlock
•
With the trimmer switched off and the
edge guide (9) resting on the ground,
place one hand on the switch handle
(20). Using your other hand, turn the
locking ring (4) anti-clockwise, as far as
it will go (approximately quarter of a turn)
(Fig. 3.1).
To adjust the handle:
L
•
•
•
With the trimmer guard resting on the
ground, depress the button (27) with
your hand.
While keeping the button depressed,
lift/lower the secondary handle to the
desired position with your other hand.
Convert
While keeping hold of the switch handle,
•
grasp the trimmer body (1) and rotate
half a turn in the direction of the arrow
(24), until the body ‘clicks’ into position
(Fig. 3.2).
Releasing the button will automatically
lock the handle in one of the preset
positions.
Lock
While still holding the switch handle,
How to alter the cutting head angle
of your trimmer (Fig. M & N)
•
tighten the locking ring clockwise, using
the other hand. Only light finger pressure
is required to secure it (Fig. 3.3).
Your trimmer has a variable cutting head angle.
•
To give you the optimum trimming angle
independent of your personal height
(Fig. C).
How to adjust the height of your
trimmer (Fig. 3)
•
To raise the handle to a more comfortable
height when in the edging mode. Tip:
Alter the cutting head angle by lowering
the handle one or two knotches, while in
the trimming mode, prior to converting to
the edging mode (Fig. M).
M
Your trimmer has a telescopic body, thus
allowing you to alter its height to give you the
most comfortable operating position.
5
•
To gain access under benches, garden
furniture and shrubs (Fig. N).
cutting line on the spool, as too much will
prevent the automatic feed system from
functioning (Fig. 6).
N
To alter the cutting head angle:
•
•
Remove any remnant of old cutting line
from the spool (17).
•
With the guard (6) resting on the ground,
depress the pedal (26) with your foot.
Push the end of the new cutting line into
one of the two holes provided in the
spool housing (17) and insert 20mm.
•
Raise/lower the switch handle (20) while
keeping the pedal depressed. The
cutting head will automatically lock when
you remove your foot from the pedal.
•
Bend the cutting line over, pulling it
through the adjacent ‘L’ shaped slot.
The cutting line should now be firmly
anchored to the spool and you may
proceed to wind it on in the direction of
the arrows (16).
Replacement line
A new spool containing 10 metres of cutting line
(cat. no. A6481) may be purchased from your
Black & Decker dealer. Alternatively, replacement
line packs are available.
•
•
Take time to wind the cutting line on
neatly, in layers. Do not criss cross.
For maximum reliability, never put on a heavier or
lighter line (e.g. fishing line) which will prevent the
automatic feed from functioning, cause motor failure
or reduce cutting performance.
When you have wound on sufficient
cutting line, temporarily park it in one of
the ‘L’ shaped slots to prevent the spool
unravelling, ensuring you leave a
minimum of 9cm (3.5") protruding.
•
Fit the spool and spool cover (8) to the
spool housing as described for fitting a
new spool.
How to fit a new spool of cutting line
(Fig. 4 & 5)
•
Disconnect your trimmer from the
power supply.
Care and maintenance
•
Remove the spool cover by pushing the
spool cover tabs (13) inwards and
upwards (Fig. 4), then pull off (it is not
necessary to push both tabs in at the
same time). The empty spool can now
be withdrawn from the drive shaft.
4
5
•
For best performance, please keep the cutting
line, spool and air slots in the trimmer body
clean. Use a dry brush or cloth to remove grass,
sap or other dirt.
•
Plastic parts may be cleaned by using a mild
soap and a cloth dampened with hot water.
Do not use any type of detergent, cleaner or
solvent which might contain chemicals which
could seriously damage the plastic. Do not spray
your trimmer with water.
•
•
Remove any dirt or grass that may have
collected inside the spool housing (12)
and cover (8).
Unwind approximately 9cm (3.5") of cutting
line (5) from the new spool (17). Feed the
cutting line through the eyelet and then
push the spool onto the centre drive shaft
(Fig. 5). Rotate as necessary to fully seat
the spool, taking care not to trap the cutting
line underneath the spool and making
sure that there is a minimum of 9cm
•
Self lubricating bearings are used in your trimmer,
therefore, lubrication is not required.
Fault finding
Before checking your trimmer for any faults,
disconnect it from the mains.
(3.5") protruding from the spool housing.
•
Replace the spool cover by aligning both
tabs on it (13) with the slots in the spool
housing and pushing them into place.
Make sure that both tabs are
•
If the trimmer will not start, check that all power
cords are properly connected. If this does not
work, check your power point, finally (UK only)
check the fuse and wiring on the extension
cord plug.
securely located.
•
If the automatic line feed fails to operate, it could
be for one of the following reasons:
How to wind new line onto an empty
spool (Fig. 6 & 7)
Line too short or line jammed on spool
•
Disconnect your trimmer from the
power supply.
•
A maximum of 10 metres of new cutting
line can be wound onto the empty spool.
The spool has an ‘Indicator’ to help you
avoid winding an excessive quantity of
6
•
Remove the spool cover (8) by pushing both
tabs (13) inwards and upwards (Fig. 4).
6
1
•
•
Lift the spool (17) approximately 6mm ( /4")
ENGLISH
from the spool housing (12), while pulling the
cutting line (5). This will allow you to lengthen
the line while clearing any line jammed inside
the spool. Ensure there is a minimum of 9cm
(3.5") protruding from the spool housing.
Unwanted products and the
environment
To replace the spool, rotate as necessary
and replace the cover by aligning both tabs
on the cover with the slots in the spool
housing and push into place. Ensure that
both tabs are securely located.
Should you find one day that your product
needs replacement, or is of no further use to
you, think of the protection of the environment.
Black & Decker service centres will accept
your old products and will dispose of them in
an environmentally safe way.
Line still jammed on spool
•
Disconnect the power supply and remove
the cover, as previously described.
•
Lift out the spool (17) completely, holding the
coiled cutting line in place to prevent it
unravelling from the spool (Fig. 7).
Black & Decker Lawn and garden
guarantee
This guarantee provides: 36 months parts cover
and 12 months labour (UK), 24 months parts
cover and labour (Australia) and 12 months
replacement product cover (New Zealand).
In all cases proof of purchase will be required.
•
•
Carefully unwind the cutting line (5) from the
spool until any crossed or trapped loops are
cleared. Rewind the cutting line evenly, in the
direction of the arrows (16) on the spool.
Temporarily park the cutting line end in one
of the ‘L’ shaped slots to prevent the spool
unravelling. Ensure you leave a minimum of
9cm (3.5") protruding.
If your Black & Decker product becomes defective ,
within the guarantee period, due to faulty materials
and workmanship, we guarantee to either replace all
defective parts, or at our discretion, replace the unit
free of charge, provided that:-
•
•
•
Turn the lever (14) backwards and forwards
to ensure it operates freely.
•
The product is returned to us or our authorised
repairers with evidence of purchase.
Remove any dirt or grass that may have
collected inside the spool housing and cover.
•
The product has been used within the
parameters of its consumer classification.
Feed the end of the line through the eyelet
and then push the spool into the centre drive
shaft while pulling the free end of the line to
release it from the ‘L’ shaped slot. To fully
seat the spool, rotate as necessary, taking
care not to trap the line underneath the
spool, and making sure that there is a
minimum of 9cm (3.5") of line protruding from
the spool housing.
•
•
The product has not been used for hire purposes.
Repairs have not been attempted by anyone other
than our own service staff or authorised repairers.
•
The failure represents normal wear and tear.
This guarantee is offered as an extra benefit and is
additional to your statutory rights.
•
Finally, replace the cover as previously
described.
The guarantee policy
Spool jammed
Failures due to the following are not covered:-
•
Remove the spool cover and the spool,
as previously described.
•
Replacing worn or damaged blades, nylon line
and chains, or cables damaged during storage
or use. These are regarded as replacement items
which wear during normal usage.
•
Remove any dirt or grass that may have
collected inside the cover and the
spool housing.
•
•
Failures as a result of sudden impact or
obvious abuse.
What to do if your trimmer
needs repair
Information on how and where to send your trimmer
for repair or service is given on the reverse of the
parts diagram. We recommend you keep this in
a safe place.
Failures due to usage not in accordance with
instructions and recommendations contained in
the instruction manual.
The use of other than genuine Black & Decker
accessories and parts may damage or reduce the
performance of you Black & Decker product and
may render the guarantee void.
Australia/New Zealand: See Black & Decker under
‘Tools electric’ in your yellow pages.
7
ENGLISH
Black & Decker after sales service
Black & Decker offers a nationwide after sales service
through company operated service centres. It is our
aim to offer excellent service, fast repairs, extensive
parts availability and full accessory support.
If you need any help or advice please contact your
local Black & Decker service centre manager. Full
details of our unique after sales service can be
obtained from any of our service centres (a full
directory is printed on the reverse of the parts
drawing included with your product).
Australia/New Zealand: See Black & Decker under
‘Tools electric’ in your yellow pages.
Other Black & Decker products
Black & Decker has a full range of outdoor power
tools that make life easy in the garden. If you would
like further information on other products, please
contact the Black & Decker service information
centre at the address on the back cover, or contact
your Black & Decker stockist. Other products include
(UK only):
Lawnmowers
Grass trimmers
Lawnrakers
Leafbuster
Hedgetrimmers
Chainsaws
Compost shredders
EC Declaration of Conformity
We declare that units:
GL570, GL580 families
conform to 89/392/EEC, 89/336/EEC,
EN60/335, 73/23/EEC
A weighted sound pressure 96dB (A)
A weighted sound power 96dB (A)
Hand/arm weighted vibration 4m/s2
Brian Cooke
Director of Engineering
Spennymoor, County Durham DL16 6JG, United Kingdom
8
Australia
Belgique/België
Deutschland
España
Black & Decker (A’asia) Pty Ltd
286-288 Maroondah Highway
North Croydon, Victoria 3136
Tel: 03 213 8200
Fax: 03 726 7150
Black & Decker Belgium NV
Weihoek 1, Nossegem
1930-Zaventem-Zuid
Tel: 02 719 07 11
Fax: 02 721 40 45
Black & Decker GmbH
Black & Decker Straße 40
6270 Idstein 2
Tel: 06126 210
Fax: 06126 212601
Black & Decker de España SA
Ctra. de Acceso a Roda de Bará, km 0,7
43883-Roda de Bará, Tarragona
Tel: 977 802011
Tlx: 56631 BLADE E
Fax: 977 802342
France
Black & Decker (France) Sarl
Le Paisy
Tel: 72 20 39 20
Tlx: 300 250
69570 Dardilly, Lyon
Fax: 72 20 39 00
Helvetia
Black & Decker AG Elektrowerkzeuge
Rutistrasse 14
8952 Schlieren, Schweiz/Suisse
Tel: 01 730 69 31 32
Tlx: 54462 BDZH CH
Fax: 01 730 70 67
Italia
Black & Decker Italia SpA
Viale Elvezia 2
Tel: 039 23 87 1
Fax: 039 23 87 59 3
20052 Monza (Mi)
Nederland
Black & Decker (Nederland) BV
Florijnstraat 10
4879 AH Etten-Leur
Tel: 01608 82000
Tlx: 54970 BLADE A
Fax: 01608 38184
N.B: Na 1 Oktober 1995 - Tel: 07650 82000
Fax: 07650 38184
New Zealand
Österreich
Black & Decker
483 Great South Road
Penrose, Auckland
Tel: 09 579 7600
Fax: 09 579 8200
Black & Decker
Tel: 0222 670 64 10
Werkzeugevertriebs GmbH
Erlaaerstrasse 165
Tlx: 13228 BLACK A
Fax: 0222 670 64 114
Postfach 69, 1235 Wien
Portugal
Black & Decker
Tel: 268 76 13/268 75 13
Tlx: 16607 BLADEC P
Fax: 267 1580
Rua Egas Moniz 173
Apartado 19, S. João do Estoril
2768 Estoril, Codex
United Kingdom
Black & Decker
210 Bath Road, Slough
Berkshire SL1 3YD
Tel: 01753 511234
Tlx: 848317 BAND MH
Fax: 01753 551155
E
Black & Decker (E
) AE
πŁ : 9242870-75
Service: 9242876-7
Fax: 9242869
. ∏ø
154
ı
Æ 176 71
R
Part no. 806891-04 2/95
English
R
|