7
7
8
6
A
B
D
F
15 16
14
C
18
17
E
3
H
G
I
J
K
L
4
M
N
O
5
(Original instructions)
ENGLISH
3. Personal safety
Intended use
Your BLACK+DECKERTM chainsaw has been designed for
pruning and felling trees and cutting logs. This tool is intended
for consumer use only.
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
Safety instructions
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
General power tool safety warnings
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric
shock, fire and/or serious injury.
@
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery oper-
ated (cordless) power tool.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
6
(Original instructions)
ENGLISH
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
Slippery or unstable surfaces such as ladders may cause
a loss of balance or control of the chainsaw.
u When cutting a limb that is under tension be alert
for spring back.
released the spring loaded limb may strike the operator
and/or throw the chain saw out of control.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
u Use extreme caution when cutting brush and saplings.
The slender material may catch the saw chain and be
whipped toward you or pull you off balance.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
u Carry the chain saw by the front handle with the chain
saw switched off and away from your body. When
guide bar cover. Proper handling of the chain saw will
reduce the likelihood of accidental contact with the moving
saw chain.
u Follow instructions for lubricating, chain tensioning
and changing accessories. Improperly tensioned or
lubricated chain may either break or increase the chance
for kickback
5. Service
a.
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
u Keep handles dry, clean, and free from oil and grease.
Greasy, oily handles are slippery causing loss of control.
u Cut wood only. Do not use chainsaw for purposes not
intended. For example: do not use the chainsaw for
cutting plastic, masonry or non-wood building materi-
als. Use of the chainsaw for operations different than
intended could result in a hazardous situation.
b. Power to the tool should always be supplied via
residual current device with a rated residual current of
30mA or less.
Additional power tool safety warnings
Warning! Additional safety warnings for
chainsaws
@
Causes and operator prevention of kickback
Kickback may occur when the nose or tip of the guide bar
touches an object, or when the wood closes in and pinches
the saw chain in the cut.
u Keep all parts of the body away from the saw chain
when the chainsaw is operating. Before you start the
chainsaw, make sure the saw chain is not contacting
anything. A moment of inattention while operating chain
saws may cause entanglement of your clothing or body
with the chain saw.
Tip contact in some cases may cause a sudden reverse reac-
tion, kicking the guide bar up and back towards the operator.
Pinching the saw chain along the top of the guide bar may
push the guide bar rapidly back towards the operator.
Either of these reactions may cause you to lose control of
the chainsaw which could result in serious personal injury.
Do not rely exclusively upon the safety devices built into your
chainsaw. As a chainsaw user, you should take several steps
to keep your cutting jobs free from accident or injury.
Kickback is the result of tool misuse and / or incorrect operat-
ing procedures or conditions and can be avoided by taking
proper precautions as given below:
u Always hold the chainsaw with your right hand on the
rear handle and your left hand on the front handle.
increases the risk of personal injury and should never be
done.
u Hold the power tool by insulated gripping surfaces
only, because the saw chain may contact hidden wir-
ing or its own cord. Saw chains contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
u Wear safety glasses and hearing protection. Further
protective equipment for head, hands, legs and feet is
recommended. Adequate protective clothing will reduce
u
-
cling the chainsaw handles. With both hands on the
chainsaw, position your body and arm to allow you to
resist kickback forces. Kickback forces can be control-
led by the operator, if proper precautions are taken. Do not
let go of the chainsaw.
the saw chain.
u Do not operate a chainsaw in a tree. Operation of a
chainsaw while up in a tree may result in personal injury.
u Always keep proper footing and operate the chain saw
u Do not overreach and do not cut above shoulder
height. This helps prevent unintended tip contact and
enables better control of the chainsaw in unexpected situ-
ations.
7
(Original instructions)
ENGLISH
u Only use replacement guide bars and chains specified
by the manufacturer. Incorrect replacement guide bars
and chains may cause chain breakage and/or kickback.
u Follow the manufacturer's sharpening and mainte-
nance instructions for the saw chain. Decreasing the
depth gauge height can lead to increased kickback.
u Striking metal, cement or any other hard material near the
wood, or buried in the wood can cause kickback.
Safety of others
u This appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
u Children should be supervised to ensure that they do not
play with the appliance.
u A dull or loose chain can cause kickback.
u Do not try to insert into a previous cut. As this could cause
kickback. Make a fresh cut every time.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or ac-
cessories.
Safety recommendations for the chainsaw
u We strongly recommend that first time users obtain practi-
cal instruction in the use of the chainsaw and protective
equipment from an experienced user. Initial practice
should be completed sawing logs on a saw horse or
cradle.
u Maintain your chainsaw when not in use. Do not store
your chainsaw for any length of time without first remov-
ing the saw chain and guide bar which should be kept
immersed in oil. Store all parts of your chainsaw in a dry,
secure place out of reach of children.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u We recommend you drain the oil reservoir prior to storage.
u Be sure of your footing and pre-plan a safe exit from a
falling tree or branches.
u Use wedges to help control felling and prevent binding the
guide bar and saw chain in the cut.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
u Saw chain care. Keep the saw chain sharp and snug on
the guide bar. Ensure the saw chain and guide bar are
clean and well oiled. Keep handles dry, clean and free
from oil and grease.
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Avoid cutting
u Prepared timber.
u Into the ground.
u Into wire fences, nails. etc.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
Additional safety instructions
u Ensure someone is nearby (but at a safe distance) in case
of an accident.
u If for any reason you have to touch the saw chain, make
sure your chainsaw is disconnected from the mains.
u The noise from this product can exceed 85 dB(A). We
therefore recommend you take appropriate measures for
the protection of hearing.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
u When handling the product the chain bar may become
hot, handle with care.
8
(Original instructions)
Electrical safety
ENGLISH
Labels on tool
The following pictograms are shown on the tool:
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
#
Warning! To reduce the risk of injury, the user
must read the instruction manual.
:
Wear eye, ear and head protectionwhen using
this product.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Wear non-silp safety footwear when using the
product.
Using an extension cable
Wear non-silp, heavy dutygloves when using this
product.
u Always use an approved extension cable suitable for the
power input of this tool (see technical data). The extension
cable must be suitable for outdoor use and marked ac-
cordingly. Up to 30 m of HO7RN-F 2 X 1.5 mm² extension
cable can be used without loss of product performance.
Before use, inspect the extension cable for signs of
damage, wear and ageing. Replace the extension cable
if damaged or defective. When using a cable reel, always
unwind the cable completely.
Do not expose the tool to rain or high humidity.
Directive 2000/14/EC guaranteed sound power.
R
E
Remove plug from the mains immediately before
maintenance or if cable is damaged or cut.
Voltage drops
u Under certain power supply conditions this product may-
cause short-time voltage drops during start-up.
u Other equipment may be affected. For example, electri-
clights may temporarily reduce in brightness.
u Contact the supply authority, if necessary, to determine
that the impedance of the power supply is lower than
0.172/0.293 ohms. Disturbances are unlikely to occur
under this condition.
Caution: Do not over tighten. Tighten by
hand. Finger tight only.
Chain oil.
Moving direction of the chain
(Marked under teh sprocket cover)..
Guard against electric shock
u Prevent body contact with earthed or grounded surfaces
(e.g. metal railings, lamp-posts etc.). Electric safety can
be further improved by using a high-sensitivity (30 mA/
30mS) Residual Current Device (RCD).
Rotate to adjust chain tension, clockwise tighten
the chain, Anti-clockwise to loose the chain.
Hold and operate the saw properly with both
hands.
Warning! The use of an RCD or other circuit
breaker unit does not release the operator
of your chainsaw from the safety instructions
and safe working practices given in this user
manual.
:
Do not operate the saw using only one hand.
Features
1. On/off switch
Contact of teh guide bar tip with any object
should be avoided! Tip contact may case the
guide bar to move suddenly upward and
backward, which may cause serious injury.
2. Lock-off button
3. Front guard/chain brake assembly
4. Guide bar
5. Chain
6. Chain cover assembly
Warning! Do not touch chain at the chip
ejection point.
9
(Original instructions)
ENGLISH
7. Chain adjust locking knob
8. Chain tension adjustment wheel
9. Chain sheath
Before use and after every 10 minutes of use, you must check
the chain tension.
10. Power cord
11. Power cord retainer
12. Oil cap
u Disconnect the tool from the mains supply
u
tension is correct when the chain (5) snaps back after be-
ing pulled 3 mm away from the guide bar (4). There should
be no "sag" between the guide bar (4) and the chain (5)
13. Oil level indicator
Assembly
Warning! Always wear protective gloves when
working on your chainsaw.
@
@
u Loosen the chain adjust locking knob (7) counterclockwise
one half turn.
u Turn the chain tension adjustment wheel (8) clockwise
until slight resistance is felt.
Warning! Before performing any assembly
or maintenance on power tools, switch off and
disconnect from mains.
u Check tension - see 'Checking the chain tension'.
u
If satisfactory, re-tighten locking knob (7), or if
Warning! Remove the cable tie that attaches
the chain to the chainbar before assembly.
more tension is required, turn adjustment wheel (8). Then
re-tighten locking Knob (7).
@
Note: Do not over-tension the chain as this will lead to
excessive wear and will reduce the life of the guide bar and
the chain.
u Place the chainsaw onto a stable surface.
u Set the front guard/chain brake assembly (3) to the
Note: When the chain is new, check the tension frequently
use because a new chain stretches slightly.
u Rotate the chain adjust locking knob (7) counterclockwise
Use
u Place the chain (5) over the guide bar (4) making sure that
the saw chain cutters on the upper part of the guide bar
Warning! Let the tool work at its own pace. Do not overload.
u Guide the chain (5) around the guide bar (4) and pull it to
create a loop to one side at the rear end of the guide bar
(4).
u
recommended chain oil. You can see the oil level in the oil
u Guide the chain (5) around the drive sprocket (14), line up
the slot in the guide bar and the centre hole of the chain
u Periodically switch off and check the oil level indicator
(13); if it is less than a quarter full, disconnect your chain-
Note: rotate chain tensioning wheel as necessary to line
centre hole with bolt (15).
Warning! Make sure that the front guard/chain brake assem-
Oiling the chain
This chainsaw is equipped with an automatic oiling system
that keeps the saw chain and guide bar constantly lubricated.
We recommend that you use only BLACK+DECKER oil during
the lifetime of your chainsaw because mixtures of different oils
could lead to the oil becoming degraded, which can drastically
shorten the lifetime of the saw chain and create additional
risks.
u Place the chain cover assembly (6) onto the chainsaw.
u Make sure that the tab (17) on the chain cover assembly
E).
u Rotate the chain adjust locking knob (7) clockwise until
Never use waste oil, thick oil or very thin sewing machine
oil. These may damage your chainsaw .Only use the correct
grade of oil (cat. no. A6023-50).
snug.
u Check the tension - see 'Checking the chain tension'
below.
u The chain saw will automatically feed oil to the chain dur
ing use.
uIf chain tension is loose - see 'Increasing the chain tension'
below.
10
(Original instructions)
ENGLISH
u Open the cut with wedges to relieve the strain on the
guide bar (4). Do not try to wrench the chainsaw free.
u Start a fresh cut.
u It is normal for a small amount of excess oil to from the
chain saw bar and chain during storage. Do not store chain
saw on top of anything that may be damaged by the
dripping oil.
Felling (fig. I - K)
Inexperienced users should not attempt to fell trees. The user
may suffer injury or cause damage to property as a result of
failure to control the direction of fall, the tree may splinter or
damaged/dead branches may fall during cutting.
u Make sure that the tool is disconnected from the mains
supply.
u Pull the front guard/chain brake assembly (3) back into the
The safe distance between a tree to be felled and bystanders,
buildings and other objects is at least 2 1/2 times the height of
the tree. Any bystander, building or object within this distance
is at risk from being struck by the tree when felled.
u The tool is now ready to use.
Switching on
Note: It will not be possible to switch the tool on if the front
guard/chain brake assembly is not in the "set" position.
u
Before attempting to fell a tree:
u Make sure that there are no local by-laws or regulations
that would prohibit or control the felling of the tree.
u Consider all conditions that may affect the direction of fall,
including:
off button (2) and then push the on/off switch (1) to start.
u When the motor starts, remove your thumb from the lock
button (2) and grip the handle firmly.
Do not force the tool, allow the tool to do the work. It will do
a better and safer job at the speed for which it is designed.
Excessive force will stretch the saw chain (5).
u The intended direction of fall.
u The natural lean of the tree.
u
Any unusual heavy limb structure or decay.
u Surrounding trees and obstacles including overhead
lines and underground drains.
How the anti-kickback chain brake works
In the event of kickback, your left hand comes in contact with
the front guard, pushing it forwards, toward the workpiece,
and stops the tool within a few fractions of a second.
u The wind speed and direction.
Pre-plan a safe exit from falling trees or branches. Make sure
that the exit route is clear of obstacles that would prevent or
hinder movement. Remember that wet grass and freshly cut
bark is slippery.
u Do not attempt to fell trees where the tree diameter is
greater than the cutting length of the chainsaw.
u Cut a direction notch to determine the direction of fall.
u Make a horizontal cut to a depth of between 1/5th and
1/3rd of the diameter of the tree, perpendicular to the line
How to test the anti-kickback chain brake (fig. A)
u Always check that the kickback brake operates correctly
before use.
u Grip the tool firmly in both hands on a firm surface make
sure the saw chain (5) is clear of the ground and switch on
(see" How to switch the chainsaw on").
u Rotate your left hand forward around the front handle so
that the back of your hand comes in contact with the front
guard/chain brake assembly (3) and push it forwards,
toward the workpiece (fig. A). The saw chain (5) should
stop within a few fractions of a second.
u
and make a notch of about 45°.
u Make a single horizontal felling cut from the other side 25
To reset after the operation of the front guard/chain brake
assembly (3) follow the instructions for "How to set the chain
brake".
J). Do not cut through to the direction notch, you could
lose control of the direction of fall.
u Drive a wedge or wedges into the felling cut to open it and
Note: Avoid re-starting the tool until you hear the motor come
to a complete rest.
Note: If chain brake in malfunctioning take the product to an
approved BLACK+DECKER service centre.
Pruning trees
Make sure that there are no local by-laws or regulations that
would prohibit or control the pruning of the tree limbs. Pruning
should only be undertaken by experienced users there is an
increased risk of the saw chain pinching and kick back.
If the saw chain (5) or guide bar (4) becomes jammed
u Switch the tool off.
u Disconnect the tool from the mains supply.
11
(Original instructions)
ENGLISH
Before pruning consideration should be given to
conditions affecting the direction of fall including:
u The length and weight of the branch to be cut.
u Any unusual heavy limb structure or decay.
u Surrounding trees and obstacles including overhead.
u The wind speed and direction.
Removing the branches from a fallen tree. When limbing,
leave larger lower limbs to support the log off the ground.
Remove the small limbs in one cut. Branches under tension
should be cut from the bottom of the branch towards the top to
avoid binding the chain saw.
u The branch being intertwined with other branches.
The operator should consider access to the tree limb and the
direction of fall. The tree branch is liable to swing towards
the tree trunk. In addition to the user bystanders, objects and
property below the branch will be at risk.
u
Trim limbs from opposite side keeping tree stem between you
and saw. Never make cuts with saw between your legs or
straddle the limb to be cut.
Troubleshooting
-
Problem
Possible cause
Possible solution
tion to a maximum depth of one third the diameter of the
branch.
Lock button not
pressed.
Tool will not start
Press the lock button.
u
Front guard in the
brake position
Reset front guard
How you should cut depends on how the log is supported.
Use a saw horse whenever possible. Always start a cut with
the saw chain running and the spiked bumper (20) in contact
-
Blown fuse
Replace fuse
Tripped RCD
Check RCD
TMains loead not
connected
Check mains supply
tion of the spiked bumper against the wood.
Chain tension is too
slack
Chain does not stop
within 2 seconds
when the tool is
switched off
Check chain tension
When supported along its whole length:
u Make a downward cut, but avoid cutting the earth as this
will blunt your saw chain quickly.
Bar/chain appear hot/
smoking
Oil tank empty
Check oil tank level
When supported at both ends:
u First, cut one third down to avoid splintering and second,
Oil hole blocked on
chain bar
E) and clear the groove
around the edge of the
chainbar.
When supported at one end:
u First cut one third up to avoid splintering and second, cut
down to prevent splintering.
Chain tension is too
tight
Check chain tension
Guide bar sprocket
nose needs greasing
Oil the guide bar
sprocket nose
When on a slope:
u Always stand on the uphill side.
Check/modify chain
direction
Chainsaw does not
cut well
Chain on backwards
u Secure the workpiece using chocks or wedges. The user
or a bystander should not steady the log by sitting or
standing on it. Make sure that the saw chain does not
contact the ground.
Sharpen
Empty oil from tank and
replace
Chainsaw not using
oil
Debris in tank
Remove debris from
hole
Oil hole in cap blocked
Debris in chain bar
Debris in oil outlet
Remove debris and
clean the chain bar
This is strongly recommended whenever possible.
u Position the log in a stable position. Always cut on the
outside of the saw horse arms. Use clamps or straps to
secure the workpiece.
Remove debris
12
(Original instructions)
ENGLISH
Maintenance
Mains plug replacement (U.K. & Ireland only)
Regular maintenance ensures a long effective life for the tool.
We recommend you make the following checks on a regular
basis.
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new
plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Warning! Before performing any maintenance on power tools:
u Switch off and disconnect the tool from the mains supply.
Oil level
Recommended fuse: 13 A.
The level in the reservoir should not be allowed to fall below
a quarter full.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
u After every few hours of use and before storage, remove
the guide bar (4) and the saw chain (5) and clean them
thoroughly.
u Make sure that the guard is clean and free from debris.
u On reassembling, turn the guide bar (4) through 180° ,
remove the chain tensioning wheel with a screwdriver and
re-attatch to the opposite side of the guide bar.
Warning! Do not overtighten.
u Oil sprocket nose via the sprocket lubriation hole (19), this
ensure an even distribution of wear around the guide bar
rails.
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials.
z
Saw chain sharpening
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
If you are to get the best possible performance from the tool it
is important to keep the teeth of the saw chain sharp.
Guidance for this procedure is found on the sharpener pack-
age. For this purpose we recomment the purchase of teh
BLACK+DECKER saw chain sharpening kit (available from
BLACK+DECKER service agents and selected dealers).
BLACK+DECKER provides a facility for the collection and re-
cycling of BLACK+DECKER products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
Replacing worn out saw chains
Replacement saw chains are available through retailers or
BLACK+DECKER service agents. Always use genuine spare
parts (Replacement chain part number A6245CS-XJ).
You can check the location of your nearest authorised repair
address indicated in this manual. Alternatively, a list of author-
ised BLACK+DECKER repair agents and full details of our
after-sales service and contacts are available on the Internet
Saw chain sharpness
The saw chain cutters will blunt immediately if they touch the
ground or a nail while cutting.
Saw chain tension
Regularly check the saw chain tension.
What to do if your chainsaw needs repair.
Your chainsaw is manufactured in accordance with the rel-
evant safety requirements. Repairs should only be carried out
may result in considerable danger to the user. We recommend
you keep this user manual in a safe place.
13
Technical data
CS2040
(Type 1)
CS2245
(Type 1)
230V
230V
Voltage
Vac
W
Power input
Length
2000W
400
2200W
450
mm
Chain speed
(no load)
m/s
12.5m/s
12.5m/s
Max cutting
length
mm
ml
397
200ml
5.5
436
150ml
5.66
II
Oil capacity
Weight
kg
Safety class
II
Level of sound pressure according to EN 60745:
pA (sound pressure) 85.7/95 dB(A), Uncertainty (K) 3/2.5 dB(A)
WA (sound power)102.1/106dB(A), Uncertainty (K) 3/2.5 dB(A)
L
L
Vibration total values (triax vector sum) according to EN 60745:
Vibration emission value (ah) 4.5/5.5m/s2, uncertainty (K) 1.5 m/s2
(Original instructions)
ENGLISH
15
Australia & New Zealand
Stanley Black & Decker
Tel.1800 338 002 (Aust) or Tel. 0800 339 258 (NZ)
00000000
05/2015
|