ASUS ZENFONE M1 X00PD User Manual

User Guide  
15060-0JL00100  
E14051  
Side features  
Audio jack  
Microphone  
Nano SIM1, Nano  
SIM2, Micro SD  
card slot  
Volume  
key  
Eject hole  
Power  
key  
Speaker  
Microphone  
Micro USB port  
Rear features  
Rear camera  
Flash  
Fingerprint  
sensor  
Charging your ASUS Phone  
To charge your ASUS Phone:  
1. Connect the USB connector into the power  
adapter’s USB port.  
2. Connect the other end of the USB cable to your  
ASUS Phone.  
3. Plug the power adapter into a wall socket.  
3
2
1
IMPORTANT!  
When using your ASUS Phone while it is plugged to  
a power outlet, the grounded power outlet must be  
near to the unit and easily accessible.  
When charging your ASUS Phone through your  
computer, ensure that you plug the USB cable to  
your computer’s USB port.  
Avoid charging your ASUS Phone in an  
environment with ambient temperature of above  
35oC (95oF).  
NOTES:  
For safety purposes, use ONLY the bundled power  
adapter and cable to avoid damaging your device  
and prevent the risk of injury.  
For safety purposes, use ONLY the bundled power  
adapter and cable to charge your ASUS Phone.  
The input voltage range between the wall outlet and  
this adapter is AC 100V - 240V. The output voltage  
of the USB cable is +5V 2A, 10W.  
Installing a Nano SIM/ microSD  
card  
To install a Nano SIM/ microSD card:  
1. Push the bundled eject pin into the hole on the  
card slot to eject the tray out.  
2. Insert the Nano SIM or microSD card into the  
appropriate slot.  
3. Push the tray to close it.  
NOTES:  
The Nano SIM card slots support GSM, WCDMA,  
FDD-LTE, and TDD-LTE network bands.  
The microSD card slot supports microSD and  
microSDHC card formats.  
IMPORTANT! When two SIM cards are inserted, only  
one SIM card slot supports 4G/3G/2G service. The other  
SIM card slot only supports 2G/3G service.  
CAUTION!  
Do not use sharp tools or solvent on your device to  
avoid scratches on it.  
Use only a standard Nano SIM card on your ASUS  
Phone.  
Federal Communications  
Commission Statement  
This device complies with part 15 of the FCC Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference,  
and (2) this device must accept any interference  
received, including interference that may cause  
undesired operation.  
Changes or modifications not expressly approved by  
the party responsible for compliance could void the  
user‘s authority to operate the equipment.  
This equipment has been tested and found to  
comply with the limits for a Class B digital device,  
pursuant to part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection  
against harmful interference in a residential  
installation. This equipment generates, uses and can  
radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may  
cause harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference to radio  
or television reception, which can be determined  
by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one  
or more of the following measures:  
-
-
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment  
and receiver.  
-
Connect the equipment into an outlet on a  
circuit different from that to which the receiver  
is connected.  
-
Consult the dealer or an experienced radio/TV  
technician for help.  
The antenna(s) used for this transmitter must not be  
co-located or operated in conjunction with any other  
antenna or transmitter.  
The country code selection is for non-US models  
only and is not available to all US models. Per FCC  
regulation, all WiFi products that are marketed in US  
must be fixed to US-operated channels only.  
The responsible party within the USA per 47 CFR  
Part 2.1077(a)(3):  
ASUS COMPUTER INTERNATIONAL (America)  
Address: Corporate Way, Fremont, CA 94539, USA  
Telephone: +1-510-739-3777  
RF Exposure Information (SAR)  
This device has been tested and meets applicable  
limits for Radio Frequency (RF) exposure.  
Specific Absorption Rate (SAR) refers to the rate at  
which the body absorbs RF energy. SAR limits are  
1.6 Watts per kilogram (over a volume containing  
a mass of 1 gram of tissue) in countries that follow  
the United States FCC limit and 2.0 W/kg (averaged  
over 10 grams of tissue) in countries that follow the  
Council of the European Union limit. Tests for SAR  
are conducted using standard operating positions  
with the device transmitting at its highest certified  
power level in all tested frequency bands.  
To reduce exposure to RF energy, use a hands-free  
accessory or other similar option to keep this device  
away from your head and body. Carry this device  
at least 15 mm away from your body to ensure  
exposure levels remain at or below the as-tested  
levels. Choose the belt clips, holsters, or other  
similar body-worn accessories which do not contain  
metallic components to support operation in this  
manner. Cases with metal parts may change the RF  
performance of the device, including its compliance  
with RF exposure guidelines, in a manner that  
has not been tested or certified, and use such  
accessories should be avoided.  
The highest FCC SAR values for the device are as  
follows:  
0.72 W/Kg @1g(Head)  
1.19 W/Kg @1g(Body)  
The FCC has granted an Equipment Authorization  
for this device with all reported SAR levels evaluated  
as in compliance with the FCC RF exposure  
guidelines. SAR information on this device is on file  
with the FCC and can be found under the Display  
searching on FCC ID: MSQX00PD.  
Canada, Industry Canada (IC)  
Notices  
This device complies with Industry Canada’s  
licence-exempt RSS standard(s). Operation is  
subject to the following two conditions:  
(1) This device may not cause interference; and  
(2) This device must accept any interference,  
including interference that may cause  
undesired operation of the device.  
Le présent appareil est conforme aux normes CNR  
d’Industrie Canada applicables aux appareils radio  
exempts de licence. Son utilisation est sujette aux  
deux conditions suivantes :  
(1) Cet appareil ne doit pas créer d’interférences  
nuisibles, et  
(2) Cet appareil doit tolérer tout type  
d’interférences, y compris celles susceptibles  
de provoquer un fonctionnement non souhaité  
de l’appareil.  
Radio Frequency (RF) Exposure Information  
The radiated output power of the Wireless Device  
is below the Industry Canada (IC) radio frequency  
exposure limits. The Wireless Device should be  
used in such a manner such that the potential  
for human contact during normal operation is  
minimized. This device has been evaluated for and  
shown compliant with the IC Specific Absorption  
Rate (“SAR”) limits when installed in specific host  
products operated in portable exposure conditions.  
Canada’s REL (Radio Equipment List) can be found  
app/sitt/reltel/srch/nwRdSrch.do?lang=eng.  
Additional Canadian information on RF exposure  
also can be found at the following web address:  
html.  
This equipment should be installed and operated  
with minimum distance 15 mm between the radiator  
and your body.  
Informations concernant l’exposition aux  
fréquences radio (RF)  
La puissance de sortie émise par cet appareil  
sans fil est inférieure à la limite d’exposition aux  
fréquences radio d’Industrie Canada (IC). Utilisez  
l’appareil sans fil de façon à minimiser les contacts  
humains lors d’un fonctionnement normal.  
Cet appareil été évalué et démontré conforme  
aux limites de DAS (Débit d’absorption spécifique)  
d’IC lorsqu’il est installé dans des produits hôtes  
particuliers qui fonctionnent dans des conditions  
d’exposition à des appareils portables.  
Ce périphérique est homologué pour l’utilisation  
au Canada. Pour consulter l’entrée correspondant  
à l’appareil dans la liste d’équipement radio (REL  
- Radio Equipment List) d’Industrie Canada rendez-  
vous sur :  
do?lang=eng.  
Pour des informations supplémentaires concernant  
l’exposition aux ondes radio au Canada, rendez-  
vous sur :  
html.  
Cet appareil doit être installé et utilisé avec un  
minimum de 15 mm de distance entre la source de  
rayonnement et votre corps.  
CAN ICES-3(B)/NMB-3(B)  
This Class B digital apparatus complies with  
Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme  
à la norme NMB-003 du Canada.  
This device and its antenna(s) must not be co-  
located or operated in conjunction with any other  
antenna or transmitter, except tested built-in radios.  
The County Code Selection feature is disabled for  
products that are marketed in the US/ Canada.  
Cet appareil et son ou ses antenne(s) ne doivent  
pas être situés près de ou utilisés conjointement  
avec une autre antenne ou un autre émetteur,  
exception faite des radios intégrées qui ont été  
testées.  
La fonction de sélection de l’indicatif du pays est  
désactivée pour les produits commercialisés aux  
États-Unis et au Canada.  
The IC ID for this device is 3568A-X00PD.  
L’identifiant Industrie Canada de cet appareil est:  
3568A-X00PD.  
EU Radio Equipment Directive  
Compliance  
Simplified EU Declaration of Conformity  
Hereby, ASUSTek Computer Inc. declares that the  
radio equipment ASUS_X00PD is in compliance with  
Directive 2014/53/EU. Full text of EU declaration  
support/. (Search for ZB555KL)  
RF Output Table  
Items  
Maximum Radio-Frequency Output Power Table  
Bluetooth BR/EDR (2402~2480  
7.00(dBm)  
MHz)  
Bluetooth  
Bluetooth 4.0-LE (2402~2480 MHz) 2.00(dBm)  
2.4GHz 802.11b (2412~2472 MHz) 15.50(dBm)  
2.4GHz 802.11g (2412~2472 MHz) 14.00(dBm)  
2.4GHz 802.11n HT20  
(2412~2472MHz)  
12.50(dBm)  
12.50(dBm)  
33.50(dBm)  
30.00(dBm)  
23.50(dBm)  
23.50(dBm)  
23.50(dBm)  
23.50(dBm)  
22.50(dBm)  
WLAN  
2.4GHz 802.11n HT40  
(2422~2462MHz)  
GSM 900 Burst (880~915 ;  
925~960 MHz)  
GSM  
GSM 1800 Burst (1710~1785 ;  
1805~1880 MHz)  
WCDMA Band I (1920~1980 ;  
2110~2170 MHz)  
WCDMA  
WCDMA Band VIII (880~915 ;  
925~960 MHz)  
LTE Band I (1920~1980 ;  
2110~2170 MHz)  
LTE Band III (1710~1785 ;  
1805~1880 MHz)  
LTE Band VII (2500~2570 ;  
2620~2690 MHz)  
LTE  
LTE Band VIII (880~915 ; 925~960 23.00(dBm)  
MHz)  
LTE Band XX (832~862 ; 791~821  
MHz)  
23.50(dBm)  
23.00(dBm)  
LTE Band XL (2300~2400 MHz)  
NOTE: This RF output power table is for EU  
member states, the EEA States, the EFTA States  
and Turkey only. The frequency range and the  
RF output power may differ from other non-EU  
countries.  
RF Exposure Information  
This ASUS product has been tested and meets  
applicable European SAR limits. The SAR limit is  
2.0 W/kg in countries that set the limit averaged  
over 10 grams of tissue. The specific maximum SAR  
values for this device are as follows:  
ASUS_X00PD(ZB555KL)  
Head: 0.397 W/Kg  
Body: 1.130 W/Kg  
When carrying this device or using it while worn on  
the body, either use an approved accessory such  
as a holster or otherwise maintain a distance of 0.5  
cm from the body to ensure compliance with RF  
exposure requirements.  
This ASUS product has been tested and meets  
applicable European SAR limits. The SAR limit is  
2.0 W/kg in countries that set the limit averaged  
over 1 grams of tissue. The specific maximum SAR  
values for this device are as follows:  
ASUS_X00PD(ZB555KL) for IN  
Head: 0.821 W/Kg  
Body: 1.180 W/Kg  
When carrying this device or using it while worn on  
the body, either use an approved accessory such  
as a holster or otherwise maintain a distance of 1  
cm from the body to ensure compliance with RF  
exposure requirements.  
CE Marking  
Laser safety information  
CLASS 1 LASER PRODUCT  
Complies with 21 CFR 1040.10 and 1040.11 except  
for deviations pursuant to Laser Notice No. 50,  
dated June 24, 2007  
Using GPS (Global Positioning  
System) on your ASUS Phone  
To use the GPS positioning feature on your ASUS  
Phone:  
Ensure that your device is connected to the  
Internet before using Google Map or any  
GPS-enabled apps.  
For first-time use of a GPS-enabled app on  
your device, ensure that you are outdoors to  
get the best positioning data.  
When using a GPS-enabled app on  
your device inside a vehicle, the metallic  
component of the car window and other  
electronic devices might affect the GPS  
performance.  
Prevention of Hearing Loss  
To prevent possible hearing damage, do not listen at  
high volume levels for long periods.  
Safety information  
CAUTION! Use of controls or adjustments or  
performance of procedures other than those  
specified herein may result in hazardous radiation  
exposure.  
ASUS Phone care  
Use your ASUS Phone in an environment with  
ambient temperatures between 0 °C (32 °F)  
and 35 °C (95 °F).  
The battery  
WARNING: Disassembling the battery by yourself  
will void its warranty and may cause serious harm.  
Your ASUS Phone is equipped with a high  
performance non-detachable Li-polymer battery.  
Observe the maintenance guidelines for a longer  
battery life.  
Do not remove the non-detachable li-polymer  
battery as this will void the warranty.  
Avoid charging in extremely high or low  
temperature. The battery performs optimally in  
an ambient temperature of +5 °C to +35 °C.  
Do not remove and replace the battery with a  
non-approved battery.  
Use only ASUS battery. Using a different  
battery may cause physical harm/injury and  
may damage your device.  
Do not remove and soak the battery in water or  
any other liquid.  
Never try to open the battery as it contains  
substances that might be harmful if swallowed  
or allowed to come into contact with  
unprotected skin.  
Do not remove and short-circuit the battery, as  
it may overheat and cause a fire. Keep it away  
from jewelry or metal objects.  
Do not remove and dispose of the battery  
in fire. It could explode and release harmful  
substances into the environment.  
Do not remove and dispose of the battery with  
your regular household waste. Take it to a  
hazardous material collection point.  
Do not touch the battery terminals.  
To avoid fire or burns, do not disassemble,  
bend, crush, or puncture the battery.  
NOTES:  
Risk of explosion if battery is replaced by an  
incorrect type.  
Dispose of used battery according to the  
instructions.  
The charger  
Use only the charger supplied with your ASUS  
Phone.  
Never pull the charger cord to disconnect it  
from the power socket. Pull the charger itself.  
Caution  
Your ASUS Phone is a high quality piece of  
equipment. Before operating, read all instructions  
and cautionary markings on the (1) AC Adapter.  
Do not use the ASUS Phone in an extreme  
environment where high temperature or high  
humidity exists. The ASUS Phone performs  
optimally in an ambient temperature between 0  
°C (32°F) and 35 °C (95 °F).  
Do not disassemble the ASUS Phone or its  
accessories. If service or repair is required,  
return the unit to an authorized service center.  
If the unit is disassembled, a risk of electric  
shock or fire may result.  
Do not short-circuit the battery terminals with  
metal items.  
Operator access with a tool  
If a TOOL is necessary to gain access to an  
OPERATOR ACCESS AREA, either all other  
compartments within that area containing a hazard  
shall be inaccessible to the OPERATOR by the use  
of the same TOOL, or such compartments shall be  
marked to discourage OPERATOR access.  
General Usage (typical body-worn) (for  
Japan)  
This device (front & rear side) should be operated  
under a seperation distance of 15 mm from the  
human body.  
* The other four sides are not in close proximity to  
the human body at the general use as described  
above.  
India E-waste (Management and  
handling) Rules 2016  
This product complies with the “India E-Waste  
(Management) Rules, 2016” and prohibits  
use of lead, mercury, hexavalent chromium,  
polybrominated biphenyls (PBBs) and  
polybrominated diphenyl ethers (PBDEs) in  
concentrations exceeding 0.1% by weight in  
homogenous materials and 0.01 % by weight in  
homogenous materials for cadmium, except for the  
exemptions listed in Schedule II of the Rule.  
India BIS - IS 16333 Notice  
Language Input : Hindi, English, Tamil  
Readability: Assamese, Bangla, Bodo(Boro),  
Dogri, Gujarati, Hindi, Kannada, Kashmiri,  
Konkani, Maithili, Malayalam, Manipuri(Bangla),  
Manipuri(Meetei Mayek), Marathi, Nepali, Oriya,  
Panjabi, Santhali, Sanskrit, Sindhi (Devanagari)  
,Tamil, Telugu, Urdu and English  
Regional notice for Singapore  
This ASUS Phone  
complies with IMDA  
Standards.  
ASUS Recycling/Takeback  
Services  
ASUS recycling and takeback programs come  
from our commitment to the highest standards for  
protecting our environment. We believe in providing  
solutions for you to be able to responsibly recycle  
our products, batteries, other components as well  
as the packaging materials. Please go to http://  
csr.asus.com/english/Takeback.htm for detailed  
recycling information in different regions.  
Proper disposal  
Risk of explosion if battery is replaced  
by an incorrect type. Dispose of used  
batteries according to the instructions.  
DO NOT throw the battery in municipal  
waste. The symbol of the crossed out  
wheeled bin indicates that the battery  
should not be placed in municipal waste.  
DO NOT throw this product in municipal  
waste. This product has been designed  
to enable proper reuse of parts and  
recycling. The symbol of the crossed out  
wheeled bin indicates that the product  
(electrical, electronic equipment and  
mercury-containing button cell battery)  
should not be placed in municipal waste.  
Check local regulations for disposal of  
electronic products.  
DO NOT throw this product in fire. DO  
NOT short circuit the contacts. DO NOT  
disassemble this product.  
WARNING  
Cancer and Reproductive Harm-  
NOTE: For more legal and e-labelling information,  
check on your device from Settings > About >  
Legal information.  
FCC COMPLIANCE INFROMATION  
Per FCC Part 2 Section 2.1077  
Responsible Party: Asus Computer International  
Address:  
800 Corporate Way, Fremont, CA 94539.  
(510)739-3777/(510)608-4555  
Phone/Fax No:  
hereby declares that the product  
Product Name :  
Model Number :  
Zenfone Max M1  
ASUS_X00PD  
compliance statement:  
This device complies with part 15 of the FCC Rules. Operation is subject to the  
following two conditions: (1) This device may not cause harmful interference,  
and (2) this device must accept any interference received, including interference  
that may cause undesired operation.  
Ver. 180125  
ASUS  
Address: 4F, No.150 Li-Te Rd., Peitou, Taipei,  
Taiwan  
Tel: 886228943447  
Fax: 886228907698  
Declaration  
We declare that the IMEI codes for this product, ASUS  
Phone, are unique to each unit and only assigned to  
this model. The IMEI of each unit is factory set and  
cannot be altered by the user and that it complies  
with the relevant IMEI integrity related requirements  
expressed in the GSM standards.  
Should you have any questions or comments regarding  
this matter, please contact us.  
Sincerely yours,  
ASUSTeK COMPUTER INC.  
Tel: 886228943447  
Fax: 886228907698  
Copyright © 2018 ASUSTeK COMPUTER INC.  
All Rights Reserved.  
You acknowledge that all rights of this Manual remain with ASUS.  
Any and all rights, including without limitation, in the Manual or  
website, and shall remain the exclusive property of ASUS and/or its  
licensors. Nothing in this Manual intends to transfer any such rights,  
or to vest any such rights to you.  
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY  
OF ANY KIND. SPECIFICATIONS AND INFORMATION  
CONTAINED IN THIS MANUAL ARE FURNISHED FOR  
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE  
AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE  
CONSTRUED AS A COMMITMENT BY ASUS.  
ZenTalk Fans Forum  
(http://www.asus.com/zentalk/global_forward.php)  

Snapper 31f700 User Manual
Sharp Cv P10lc User Manual
Samsung Aw12p2 User Manual
Omega Speaker Systems Drx St User Manual
Lanier 5455 User Manual
Hampton Bay Diy 300ps User Manual
GE AHH10 User Manual
DELVCAM DELV 12GSDI 15 User Manual
CRICKET MOTOROLA MOTO E5 SUPRA XT1924 6 User Manual
BLACK DECKER MZ2300P User Manual