TUF Gaming Monitor
VG259QM series
User Guide
Contents
Notices.......................................................................................................... iv
Safety.information........................................................................................ v
Care.&.Cleaning........................................................................................... vi
Takeback.Services..................................................................................... vii
iii
Notices
Federal.Communications.Commission.Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modifications
to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
Canadian.Department.of.Communications.Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
This Class B digital apparatus meets all requirements of the Canadian Interference
- Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement
sur le matériel brouiller du Canada.
iv
Safety information
•
Before setting up the monitor, carefully read all the documentation that came
with the package.
•
•
To prevent fire or shock hazard, never expose the monitor to rain or moisture.
Never try to open the monitor cabinet. The dangerous high voltages inside the
monitor may result in serious physical injury.
•
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified
service technician or your retailer.
Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
•
•
Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or over a
radiator or heat source unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
•
•
Use the appropriate power plug which complies with your local power standard.
Do not overload power strips and extention cords. Overloading can result in fire
or electric shock.
•
•
•
•
Avoid dust, humidity, and temperature extremes. Do not place the monitor in
any area where it may become wet. Place the monitor on a stable surface.
Unplug the unit during a lightning storm or if it will not be used for a long period
of time. This will protect the monitor from damage due to power surges.
Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked between
100-240V AC.
•
•
If you encounter technical problems with the monitor, contact a qualified
service technician or your retailer.
Adjustment of the volume control as well as the equalizer to other settings
than the center position may increase the ear-/headphones output voltage and
therefore the sound pressure level.
•
The adapter is only used for this monitor, do not use it for other purpose.
Your device uses one of the following power supplies:
- Manufacturer: Delta Electronics Inc., Model: ADP-40KD BB
This symbol of the crossed out wheeled bin indicates that the product (electrical,
electronic equipment, and mercury-containing button cell battery) should not
be placed in municipal waste. Please check local regulations for disposal of
electronic products.
v
AEEE.yönetmeliğine.uygundur
Care & Cleaning
•
Before you lift or reposition your monitor, it is better to disconnect the cables
and power cord. Follow the correct lifting techniques when positioning the
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.
Do not lift the display by the stand or the cord.
•
•
Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed
with a cloth dampened with mild cleaner.
Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended
for use with the monitor. Never spray cleaner directly on the screen, as it may
drip inside the monitor and cause an electric shock.
The.following.symptoms.are.normal.with.the.monitor:
•
The screen may flicker during the initial use due to the nature of the fluorescent
light. Turn off the Power Switch and turn it on again to make sure that the
flicker disappears.
•
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
When the same image is displayed for hours, an afterimage of the previous
screen may remain after switching the image. The screen will recover slowly or
you can turn off the Power Switch for hours.
•
When the screen becomes black or flashes, or cannot work anymore, contact
your dealer or service center to fix it. Do not repair the screen by yourself!
Conventions.used.in.this.guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying
to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
vi
Where.to.find.more.information
Refer to the following sources for additional information and for product and
software updates.
1.. ASUS.websites
The ASUS websites worldwide provide updated information on ASUS
2.. Optional.documentation
Your product package may include optional documentation that may have
been added by your dealer. These documents are not part of the standard
package.
Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions for
our customers to be able to responsibly recycle our products, batteries and other
components as well as the packaging materials.
information in different region.
vii
viii
1.1
Welcome!
Thank you for purchasing the ASUS® LCD monitor!
The latest widescreen LCD monitor from ASUS provides a broader, brighter and
crystal-clear display, plus a host of features that enhance your viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the monitor brings to you!
1.2
Package contents
Check your package for the following items:
LCD monitor
Monitor base
Quick start guide
Warranty card
Power adapter
Power cord
DisplayPort cable (optional)
HDMI cable (optional)
If any of the above items is damaged or missing, contact your retailer
immediately.
ASUS TUF Gaming Monitor VG259QM series
1-1
1.3 Monitor introduction
1.3.1.
Front.view
1
2
3
4
5
1.
2.
(
5-way) button:
• Turns on the OSD menu. Enacts the selected OSD menu item.
• Increases/Decreases values or moves your selection up/down/left/right.
• Displays the input selection bar when the monitor enters standby mode
or displays the “NO SIGNAL“ message.
button
• Exits the OSD menu item.
• Displays the input selection bar when the monitor enters standby mode
or displays the “NO SIGNAL“ message.
• Toggles the Key Lock function between on and off with a long press for 5
seconds.
3.
4.
Shortcut 1 button:
• Default: GamePlus.
• To change the shortcut function, go to the MyFavorite > Shortcut >
Shortcut 1 menu.
• Displays the input selection bar when the monitor enters standby mode
or displays the “NO SIGNAL“ message.
Shortcut 2 button:
• Default: GameVisual.
1-2
Chapter 1: Product introduction
• To change the shortcut function, go to the MyFavorite > Shortcut >
Shortcut 2 menu.
• Displays the input selection bar when the monitor enters standby mode
or displays the “NO SIGNAL“ message.
5.
Power button/power indicator
• Turns the monitor on/off.
• The color definition of the power indicator is as the below table.
Status
Description
White
Amber
OFF
ON
Standby mode/No signal
OFF
1.3.2.
Back.view
4
5
6
7
8
1.. DC-IN.port. This port connects the power cord.
2.. HDMI.port. This port is for connection with an HDMI compatible device.
3.. HDMI.port. This port is for connection with an HDMI compatible device.
4.. DisplayPort. This port is for connection for a DisplayPort compatible device.
5.. Earphone.jack. This port is only available when an HDMI/DisplayPort cable
is connected.
6.. This port is for service only. (USB Type-A)
7.. Kensington.lock.slot.
8.. Control.buttons.
ASUS TUF Gaming Monitor VG259QM series
1-3
1.3.3
GamePlus Function
The GamePlus function provides a toolkit and creates a better gaming environment
for users when playing different types of games. The crosshair overlay with 6
different crosshair options letting you choose the one that best suits the game
you're playing. There's also an onscreen timer you can position on the left of the
display so you can keep track of the elapsed gaming time; while the FPS (frames
per second) counter lets you know how smooth the game is running. Display
Alignment displays alignment lines on 4 sides of the screen, serving as an easy
and handy tool for you to line up multiple monitors perfectly. Sniper function (only
available when HDR is disabled on your device) is customized for first-person
shooters. You can select the magnification ratio and the type of alignment in
sequence.
To active GamePlus:
1.
Press the GamePlus hotkey.
2.
3.
Move the
Press the
(
) button up/down to select among different functions.
) button or move the ) button right to confirm the
) button up/down to navigate
) button left to go back, off, and exit.
) button to activate it.
(
(
function you choose, and move the
through the settings. Move the
(
(
4.
Highlight the desired setting and press the
Press the button to inactivate it.
(
GamePlus
Main Menu
GamePlus —
Crosshair
GamePlus —
Timer
GamePlus —
FPS counter
GamePlus —
Sniper
GamePlus
GamePlus
GamePlus
GamePlus
GamePlus
Crosshair
(Practice Mode)
FPS
Timer
FPS
FPS Counter
Display Alignment
Sniper
(Practice Mode)
1-4
Chapter 1: Product introduction
1.3.4.
GameVisual.Function
The GameVisual function helps you select among different picture modes in a
convenient way.
To active GameVisual:
Press the GameVisual hotkey repeatedly to select.
•. Scenery.Mode: This is the best choice for scenery photo displaying with
GameVisualTM Video intelligence Technology.
•. Racing.Mode: This is the best choice for racing game playing with
GameVisualTM Video intelligence Technology.
•. Cinema.Mode: This is the best choice for movie watching with
GameVisualTM Video intelligence Technology.
•. RTS/RPG.Mode: This is the best choice for Real-Time Strategy (RTS)/
Role-Playing Game (RPG) playing with GameVisualTM Video intelligence
Technology.
•. FPS.Mode: This is the best choice for First Person Shooter game playing
with GameVisualTM Video intelligence Technology.
•. sRGB.Mode: This is the best choice for viewing photos and graphics
from PCs.
•. MOBA.Mode: This is the best choice for multiplayer online battle arena
game playing with GameVisualTM Video intelligence Technology.
•
•
•
In the Racing mode, the following function(s) are not user-configurable:
Saturation, Skin Tone, ASCR.
In the sRGB mode, the following function(s) are not user-configurable:
Brightness, Contrast, Saturation, Color Temp., Skin Tone, ASCR.
In the MOBA mode, the following function(s) are not user-configurable:
Saturation, Skin Tone, ASCR.
ASUS TUF Gaming Monitor VG259QM series
1-5
1-6
Chapter 1: Product introduction
2.1
Assembling the monitor arm/base
To assemble the monitor base:
1.
2.
Have the front of the monitor face down on a table.
Attach the base into the arm, making sure the tab on the arm fits into the groove
on the base.
3.
Fix the base to the arm by fastening the bundled screw.
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
ASUS TUF Gaming Monitor VG259QM series
2-1
2.2
Adjusting the monitor
•
For optimal viewing, we recommend that you look at the full face of the
monitor, then adjust the monitor to the angle that is most comfortable for you.
•
•
Hold the stand to prevent the monitor from falling when you change its angle.
The recommended adjusting angle is +33˚ to -5˚ (for tilt)/+90˚ to -90˚ (for
swiveling/ +130 mm (for height adjustment)/90˚ (for portrait view).
-5°~+33°
130mm
90°
90°
0°
It is normal that the monitor slightly shakes while you adjust the viewing angle.
Pivoting.the.monitor
1.
2.
3.
Lift the monitor to the highest position.
Tilt the monitor to its maximum angle.
Pivot the monitor to the angle you need.
-5°~+33°
0°
0°
90°
90°
It is normal that the monitor slightly shakes while you adjust the viewing angle.
2-2
Chapter 2: Setup
2.3
Detaching the arm (for VESA wall
mount)
The detachable arm/base of this monitor is specially designed for VESA wall
mount.
To detach the arm/base:
1.
2.
3.
4.
Have the front of the monitor face down on a table.
Remove the rubbers in the four screw holes. (Figure 1)
Remove the base (Figure 2).
Use a screwdriver to remove the screw on the hinge (Figure 3), then remove
the hinge.
1
1
2
2
(Figure 1)
(Figure 2)
(Figure 3)
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
ASUS TUF Gaming Monitor VG259QM series
2-3
2.4
Connecting the cables
Connect the cables as the following instructions:
For service only
•. To.connect.the.power.cord:
a. Connect the power adapter securely to the monitor’s DC input.
b. Connect one end of the power cord to the power adapter and the other
end to a power outlet.
•. To.connect.the.DisplayPort/HDMI.cable:
a. Plug one end of the DisplayPort/HDMI cable to the monitor’s
DisplayPort/HDMI port.
b. Connect the other end of the DisplayPort/HDMI cable to your computer's
DisplayPort/HDMI port.
•. To.use.the.earphone: connect the end with plug type to the monitor’s
earphone jack when an HDMI or DisplayPort signal is fed.
2.5
Turning on the monitor
Press the power button
. See page 1-2 for the location of the power button. The
power indicator lights up in white to show that the monitor is ON.
2-4
Chapter 2: Setup
3.1
OSD (On-Screen Display) menu
3.1.1.
How.to.reconfigure
ASUS TUF Gaming VG259QM HDR Off
Gaming
Racing Mode DisplayPort 1920x1080@ 60Hz
Overclocking
OverDrive
Adaptive-Sync (DP)
ELMB SYNC
GamePlus
GameVisual
Shadow Boost
1.
2.
Press the
Move the
(
) button to activate the OSD menu.
(
) button up/down to navigate through the functions.
Highlight the desired function and press the
(
) button to activate it. If
) button up/down
the function selected has a sub-menu, move the
(
again to navigate through the sub-menu functions. Highlight the desired sub-
menu function and press the
right to activate it.
(
) button or move the
(
) button
3.
4.
Move the
function.
(
) button up/down to change the settings of the selected
To exit and save the OSD menu, press the
) left repeatedly until the OSD menu disappears. To adjust other
functions, repeat steps 1-3.
button or move the
(
3.1.2.
OSD.function.introduction
1..
Gaming
ASUS TUF Gaming VG259QM HDR Off
Racing Mode DisplayPort 1920x1080@ 60Hz
Gaming
Overclocking
OverDrive
Adaptive-Sync (DP)
ELMB SYNC
GamePlus
GameVisual
Shadow Boost
ASUS TUF Gaming Monitor VG259QM series
3-1
•.
Overclocking:
*.
*.
ON: This function allows you to adjust the refresh rate.
Max.Refresh.Rate: Allows you to select a maximum refresh rate
of 280Hz (Only for DisplayPort input). After selecting, press the
(
) button to activate the setting.
Overclocking may cause screen flickering. To reduce such effects, disconnect
the DisplayPort cable and use the monitor OSD menu to try again with a safer
Max. Refresh rate.
•.
•.
OverDrive: Improves the gray level response time of the LCD panel.
This function is not available when ELMB.SYNC is enabled.
Adaptive-Sync.(DP)/.Variable.Refresh.Rate:.Allows an Adaptive-Sync
supported* graphics source to dynamically adjust display refresh rate
based on typical content frame rates for power efficient, virtually stutter
free and low-latency display update.
•.
Adaptive-Sync.(DP)/.Variable.Refresh.Rate can only be activated within
48Hz~240Hz for HDMI and 48Hz~280Hz for DisplayPort.
•
For supported GPUs, minimum PC system and driver requirements,
please contact the GPU manufactures.
•.
ELMB.SYNC: Allows you to turn on the function when Adaptive-Sync.
(DP)/.Variable.Refresh.Rate is On. This function eliminates screen
tearing, reduces ghosting and motion blur when playing games.
When Adaptive-Sync.(DP)/.Variable.Refresh.Rate is Off, this function can
only be activated when the refresh rate is 120Hz, 144Hz, 240Hz, 270Hz or
280Hz.
•.
•.
•.
GamePlus: See 1.3.3.GamePlus.Function for details.
GameVisual: See 1.3.4.GameVisual.Function for details.
Shadow.Boost: Dark color enhancement adjusts monitor gamma curve
to enrich the dark tones in an image, making dark scenes and objects
much easier to be seen.
This function is only available in Racing mode, RTS/RPG mode, FPS mode, or
sRGB mode.
3-2
Chapter 3: General Instructions
2..
Image
ASUS TUF Gaming VG259QM HDR Off
Image
Racing Mode DisplayPort 1920x1080@ 60Hz
Brightness
Contrast
HDR
VividPixel
ASCR
Aspect Control
Blue Light Filter
•.
•.
•.
Brightness: The adjusting range is from 0 to 100.
Contrast: The adjusting range is from 0 to 100.
HDR: Contains two HDR modes.
*.
ASUS.Gaming.HDR: Is the HDR mode that ASUS has specially
adjusted for HDR performance.
*.
ASUS.Cinema.HDR: Complies with VESA Display HDR.
When detecting HDR content, an “HDR ON” message will pop up. When
displaying HDR content, the following function(s) are not available: ELMB Sync,
Sniper, GameVisual, Shadow Boost, Brightness, Contrast, ASCR, Aspect
Control, Blue Light Filter, Color Temp., Gamma, Saturation.
•.
VividPixel:.Enhances the outline of the displayed picture and generates
high-quality images on screen.
•.
•.
•.
ASCR: Turns on/off the ASCR (ASUS Smart Contrast Ratio) function.
Aspect.Control: Adjusts the aspect ratio to Full, or 4:3.
Blue.Light.Filter
*.
*.
Level.0:.No change.
Level.1~4: The higher the level, the less blue light is scattered.
When Blue Light Filter is activated,the default settings of Racing
Mode will be automatically imported. Between Level 1 to Level 3,
the Brightness function is user-configurable. Level 4 is optimized
setting. It is compliance with TUV Low Blue Light Certification.
The Brightness function is not user-configurable.
Please refer to the following to alleviate eye strains:
•
Users should take some time away from the display if working for long
hours. It is advised to take short breaks (at least 5 mins) after around 1
hour of continuous working at the computer. Taking short and frequent
breaks is more effective than a single longer break.
ASUS TUF Gaming Monitor VG259QM series
3-3
•
•
To minimize eye strain and dryness in your eyes, users should rest the
eye periodically by focusing on objects that are far away.
Eye exercises can help to reduces eye strain. Repeat these exercises
often. If eye strain continues please consult a physician. Eye exercises: (1)
Repeating look up and down (2) Slowly roll your eyes (3) Move your eyes
diagonal.
•
High energy blue light may lead to eye strain and AMD (Age-Related
Macular Degeneration). Blue light Filter to reduce 70% (max.) harmful
blue light to avoiding CVS (Computer Vision Syndrome).
3..
Color
Set a desired color setting from this menu.
ASUS TUF Gaming VG259QM HDR Off
Racing Mode DisplayPort 1920x1080@ 60Hz
Color
Color Temp.
Saturation
Skin Tone
•.
Color.Temp.: Contains 4 modes including Cool, Normal, Warm, and
User Mode.
•.
•.
Saturation: the adjusting range is from 0 to 100.
Skin.Tone: Contains three color modes including Reddish, Natural, and
Yellowish.
4.. Input.Select.
In this function, you can select your desired input source.
ASUS TUF Gaming VG259QM HDR Off
Racing Mode DisplayPort 1920x1080@ 60Hz
Input Select
HDMI-1
HDMI-2
DisplayPort
3-4
Chapter 3: General Instructions
5..
MyFavorite
ASUS TUF Gaming VG259QM HDR Off
Racing Mode DisplayPort 1920x1080@ 60Hz
MyFavorite
Shortcut
Customized Setting
•.
•.
Shortcut:
*.
Shortcut.1/Shortcut.2: Sets the shortcut functions for shortcut
buttons.
When a certain function is selected or activated, your shortcut button may not
support. Available function choices for shortcut: GamePlus (only for Shortcut.
1), GameVisual (only for Shortcut.2), Brightness, Contrast, HDR, Blue Light
Filter, Color Temp., Volume.
Customized.Setting: Loads/Saves all settings on the monitor.
6..
System.Setup.
ASUS TUF Gaming VG259QM HDR Off
System Setup
Racing Mode DisplayPort 1920x1080@ 60Hz
Language
Sound
ECO Mode
Power Indicator
Power Key Lock
Key Lock
OSD Setup
More
•.
•.
Language: There are 21 languages for your selection, including English,
French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech,
Croatian, Polish, Romanian, Hungarian, Turkish, Simplified Chinese,
Traditional Chinese, Japanese, Korean, Thai, Indonesian, Persian.
Sound: Sets the sound related settings from this menu.
*.
*.
Volume: The adjusting range is from 0 to 100.
Mute: Toggles the monitor sound between on and off.
•.
•.
ECO.Mode: reduces power consumption.
Power.Indicator: Turn the power LED indicator on/off.
ASUS TUF Gaming Monitor VG259QM series
3-5
•.
•.
Power.Key.Lock: Enables or disables the power key.
Key.Lock: To disable all function keys. Press
over 5 seconds to
cancel the key lock function.
•.
OSD.Setup:
*
*
*
Adjusts the OSD timeout from 10 to 120 seconds.
Enables or disables the DDC/CI function.
Adjusts the OSD background from opaque to transparent.
•.
DisplayPort.Ver.: Compatibility with graphic card. Select DisplayPort.1.1
or DisplayPort.1.2+HDR by graphic card DP version.
DisplayPort.1.1 is only available when OverClocking and Adaptive-Sync.
(DP)/.Variable.Refresh.Rate are off.
•.
•.
Information: Shows the monitor information.
All.Reset: “Yes” allows you to restore the default settings.
3-6
Chapter 3: General Instructions
3.2
Specifications summary
Panel.Type
Panel.size
Max..Resolution
Pixel.pitch
Brightness.(Typ.)
Contrast.Ratio.(Typ.)
Contrast.Ratio.(Max.)
Viewing.angle(H/V).CR>10
Display.colors
Response.time
Color.temperature.selection
Analog.input
TFT LCD
24.5”W (16:9, 62.2 cm) wide screen
1920 x 1080
0.2832 mm x 0.2802 mm
400 cd/m2
1000:1
100,000,000:1 (with ASCR on)
178˚/178˚
16.7 M
1 ms (Gray to gray)
4 color temperatures
No
Digital.input
HDMI v2.0 x 2, DisplayPort v1.2 x 1
Earphone.jack
Audio.input
Yes
No
Speaker.(Built-in)
USB.3.0.port
2 W x 2 Stereo, RMS
No
Colors
Black
Power.LED
Tilt
White (On)/Amber (Standby)
+33˚~ -5˚
Pivot
Swivel
Height.adjustment
VESA.wall.mount
Kensington.lock
Voltage.rating
+90˚~ -90˚
+90˚~ -90˚
130 mm
100 x 100 mm
Yes
AC: 100~240V
DC: 19V, 2.1A (AC adapter)
Power.consumption
Power On: < 20 W**, Standby: < 0.5 W,
Power Off: < 0.5 W
Temperature.(Operating)
0˚C~40˚C
Temperature.(Non-operating)
-20˚C~+60˚C
Dimensions. (W. x. H. x. D). without. 563 x 330 x 52 mm
stand
Dimensions.(W.x.H.x.D).with.stand 563 x 486 x 212 mm (highest)
563 x 356 x 212 mm (lowest)
664 x 415 x 221 mm (package)
Weight.(Esti.)
5.1 kg (Net); 2.8 kg (without stand); 7.5 kg
(Gross)
ASUS TUF Gaming Monitor VG259QM series
3-7
Multi-languages
21 languages (English, French, German,
Italian, Spanish, Dutch, Portuguese, Russian,
Czech, Croatian, Polish, Romanian, Hungarian,
Turkish, Simplified Chinese, Traditional Chinese,
Japanese, Korean, Thai, Indonesian, Persian)
Accessories.
Quick start guide, warranty card, power adapter,
power cord, DisplayPort cable (optional), HDMI
cable (optional)
Compliance.and.Standards
UL/cUL, CB, CE, ErP, FCC, CCC, CU, RCM,
BSMI, VCCI, RoHS, J-MOSS, WEEE, Windows
7 & 8.1 & 10 WHQL, CEL, MEPS, PSE,
UkrSEPRO, KCC, E-Standby, TUV-Flicker Free,
TUV-Low Blue Light, ICES-3, PC Recycle
*Specifications.are.subject.to.change.without.notice.
**Measuring.a.screen.brightness.of.200.nits.without.audio/.USB/.Card.reader.
connection.
3-8
Chapter 3: General Instructions
3.4
Troubleshooting (FAQ)
Problem
Possible.Solution
Power LED is not ON
•
•
Press the
is in the ON mode.
Check if the power cord is properly
connected to the monitor and the power
outlet.
button to check if the monitor
The power LED lights amber and there is
no screen image
•
•
•
•
Check if the monitor and the computer are
in the ON mode.
Make sure the signal cable is properly
connected the monitor and the computer.
Inspect the signal cable and make sure
none of the pins are bent.
Connect the computer with another
available monitor to check if the computer
is properly working.
Screen image is too light or dark
•
•
Adjust the Contrast and Brightness
settings via OSD.
Screen image bounces or a wave pattern is
present in the image
Make sure the signal cable is properly
connected to the monitor and the
computer.
•
Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does • Inspect the signal cable and make sure
not look white)
that none of the pins are bent.
Perform All Reset via OSD.
Adjust the R/G/B color settings or select
the Color Temperature via OSD.
•
•
3-10
Chapter 3: General Instructions
3.5
Supported operating mode
Resolution.Frequency
640x350
Refresh.Rate.
70Hz
85Hz
60Hz
67Hz
75Hz
85Hz
70Hz
85Hz
56Hz
60Hz
72Hz
75Hz
85Hz
75Hz
60Hz
60Hz
70Hz
75Hz
85Hz
75Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
75Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
75Hz
60Hz
60Hz
Horizontal.Frequency
31.469KHz
37.861KHz
31.469KHz
35KHz
640x350
640x480
640x480
640x480
37.5KHz
640x480
43.269KHz
31.469KHz
37.927KHz
35.156KHz
37.88KHz
48.077KHz
46.875KHz
53.674KHz
49.71KHz
31.02KHz
48.363KHz
56.476KHz
60.023KHz
68.677KHz
67.5KHz
720x400
720x400
800x600
800x600
800x600
800x600
800x600
832x624
848x480
1024x768
1024x768
1024x768
1024x768
1152x864
1280x720
1280x720
1280x720
1280x768
1280x800
1280x800
1280x800
1280x960
1280x1024
1280x1024
1366x768
1440x900
1440x900
1440x900
1680x1050
1680x1050
45KHz
44.772KHz
56.456KHz
47.396KHz
49.306KHz
49.702KHz
62.795KHz
60KHz
63.981KHz
79.976KHz
47.712KHz
55.469KHz
55.935KHz
70.635KHz
64.674KHz
65.29KHz
ASUS TUF Gaming Monitor VG259QM series
3-11
Resolution.Frequency
1920x1080
Refresh.Rate.
60Hz
Horizontal.Frequency
66.587KHz
1920x1080
60Hz
67.5KHz
1920x1080
85Hz
95.43KHz
1920x1080
100Hz
113.3KHz
1920x1080*
1920x1080*
1920x1080*
1920x1080 (DP)*
1920x1080 (DP)*
640x480P
120Hz
137.2KHz
144Hz
158.11KHz
240Hz
291.309KHz
308.33KHz
270Hz
280Hz
307.84KHz
59.94/60Hz
59.94/60Hz
50Hz
31.469KHz/31.5KHz
31.469KHz/31.5KHz
31.25KHz
720x480P
720x576P
1280x720P
1280x720P
1440x480P
1440x576P
1920x1080P
1920x1080P
50Hz
37.5KHz
59.94/60Hz
59.94/60Hz
50Hz
44.955KHz/45KHz
31.469KHz/31.5KHz
31.25KHz
50Hz
56.25KHz
59.94/60Hz
67.433KHz/67.5KHz
Note:.You.must.select.one.of.the.“*”.timings.for.enabling.ELMB.or.144Hz.feature.with.a.compatible.
GPU.graphic.card.
3-12
Chapter 3: General Instructions
|