ACER EMACHINES E510 User Manual

eMachines E510 Series

Service Guide

Service guide files and updates are available

on the ACER/CSD web; for more information,

please refer to http://csd.acer.com.tw

PRINTED IN TAIWAN

transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in

any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without

the prior written permission of Acer Incorporated.

Disclaimer

The information in this guide is subject to change without notice.

Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the

contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular

purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the

programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its

dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential

damages resulting from any defect in the software.

Acer is a registered trademark of Acer Corporation.

Intel is a registered trademark of Intel Corporation.

Pentium and Pentium II/III are trademarks of Intel Corporation.

Other brand and product names are trademarks and/or registered trademarks of their respective holders.

III

Conventions

The following conventions are used in this manual:

SCREEN MESSAGES

Denotes actual messages that appear

on screen.

NOTE

Gives bits and pieces of additional

information related to the current

topic.

WARNING

CAUTION

Alerts you to any damage that might

result from doing or not doing specific

actions.

Gives precautionary measures to

avoid possible hardware or software

problems.

IMPORTANT

Reminds you to do specific actions

relevant to the accomplishment of

procedures.

Preface

Before using this information and the product it supports, please read the following general information.

1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION

decided for Acer's "global" product offering. To better fit local market requirements and enhance product

competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.

add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered

in this generic service guide. In such cases, please contact your regional offices or the responsible

personnel/channel to provide you with further technical details.

2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information

available on your regional web or channel. If, for whatever reason, a part number change is made, it will

not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer

office may have a DIFFERENT part number code to those given in the FRU list of this printed Service

Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and

service of customer machines.

Chapter 1

System Specifications

Features

Below is a brief summary of the computer’s many feature:

Operating System

•

Genuine Windows® VistaTM Capable

Genuine Windows® VistaTM Home Basic / Home Premium / Ultimate / Business Edition

Genuine Windows® XP Home / Professional Edition (Service Pack 2)

Genuine Windows® XP Media Center / Tablet Edition

Genuine Windows® 2000 (Service Pack 4)

NOTE: Windows® VistaTM Capable PCs come with Windows® XP installed, and can be upgraded to

Windows® VistaTM. For more information on Windows® VistaTM and how to upgrade, go to:

Microsoft.com/windowsvista.

Platform

•

Intel® Celeron® (Santarosa) processor technology, featuring:

•

Intel® Celeron processor

Mobile Intel® GL960 Express Chipset

Intel® Wireless Atheros / Broadcom

System Memory

•

Dual-Channel DDR2 SDRAM support

Up to 1 GB of DDR2 553 MHz memory, upgradeable to 2 GB using two soDIMM modules*

•

Display and graphics

•

14.1" WXGA 1280 x 800

Mobile Intel® GL960 Express Chipset

•

Storage subsystem

•

2.5" hard disk drive

Optical drive options:

DVD-Super Multi double-layer drive

•

5-in-1 card reader

Audio

•

Built-in stereo speakers

S/PDIF (Sony/Philips Digital Interface) support for digital speakers

Chapter 1

•

Built-in microphone

Dimensions and Weight

•

366 (W) x 274 (D) x 33.6/42.6 (H) mm (14.4 x 10.78 x 1.32/1.67 inches)

2.8 kg (6.16 lbs.)

•

Communication

•

Acer Video Conference, featuring:

•

Integrated Acer Crystal Eye webcam

Acer Video Conference Manager software

Acer PureZone technology

Optional Acer Xpress VoIP phone

•

WLAN: Atheros / Broadcom

LAN: Gigabit Ethernet; Wake-on-LAN ready

Privacy control

•

BIOS user, supervisor, HDD passwords

Kensington lock slot

•

Power subsystem

•

ACPI 3.0

48.8 W 4400 mAh*

3-pin 65 W AC adapter*

Energy Star 4.0

Special keys and controls

•

88-/89-/93-key keyboard

Touch Pad pointing device

WLAN button/Switch

I/O interface

•

3 USB 2.0 ports

Headphone port

Microphone-in jack

Line-in

Ethernet port

DC-in jack for AC adapter

Kensington Lock (7.5mm diameter)

Environment

•

Temperature:

Chapter 1

•

Operating: 5 °C to 35 °C

Non-operating: -20 °C to 65 °C

•

Humidity (non-condensing):

•

Operating: 20% to 80%

Non-operating: 20% to 80%

Chapter 1

System Block Diagram

Chapter 1

Board Layout

Top View

2 3 4

1100

1155

1166

1122

1133 1144

JP1

LCD Connector

JP36

Mainboard to LED Board

Connector

JP3

JP34

JP4

Speaker (Left) Connector

Speaker (Right) Connector

Internal MIC Connector

South Bridge (ICH8M)

U12

JP9

PCI Express Card Socket

Power/Suspend LED

LED1

LED2

JP13

Battery Charge/Discharge LED

JP6

Internal Track-Pad Connector

Mainboard to Audio Board

Connector

JP5

JP2

Internal Keyboard Connector

JP11

JP12

Mainboard to USB Board

Connector

Mainboard to Button Board

Connector

Bluetooth Module Connector

Chapter 1

Bottom View

22 23 25

PJP1

PJP2

JP14

JP15

JP25

JP20

JP19

JP17

JP22

JP16

JP19

JP18

JP23

DC-in Power Jack

Battery Connector

CRT Connector

DVI-D Connector

ODD Connector

JP24

TV-out Connector

JP26

JP27

U23

IEEE1394 Connector

SATA HDD Connector

North Bridge (965PM/965GM)

U28

Mini Card (WLAN) Socket

Mini Card (TV-Tuner) Socket

MDC Connector

U29

Volume Control

JP28

JP29

JP31

JP32

U33

DDRII Memory Socket

Headphone/SPDIF Jack

Mic-in Jack

CPU Socket

Internal Fan Connector

VGA Board Connector

RJ45 (LAN) Connector

USB (Dual) Connectors

Audio Codec Controller

Line-in Jack

JP33

Chapter 1

Your Acer Notebook Tour

After knowing your computer features, let us show you around your new Aspire computer.

Front View

Icon

Item

Description

Built-in camera

0.3 megapixel web camera for video

communication.

Power button

Turns the computer on and off.

Easy-launch buttons

Buttons for launching frequently used

programs.

Wirelesscommunication Enables/disables the wireless function.

button/indicator

Indicates the status of wireless LAN

communication.

Bluetooth

Enables/disables the Bluetooth function.

communication button/

indicator

Indicates the status of Bluetooth

communication.

Chapter 1

Keyboard

Touchpad

For entering data into your computer.

Touch-sensitive pointing device which

functions like a computer mouse.

Click buttons (left,

center, and right)

The left and right buttons function like the

left and right mouse buttons.

Microphone

Internal microphone for sound recording.

Display screen

Also called Liquid-Crystal Display (LCD),

displays computer output.

Status indicators

Light-Emitting Diodes (LEDs) that light up

to show the status of the computer’s

functions and components.

Empowering button

Speaker

Launches the Empowering Technology

toolbar.

Left and right speakers deliver stereo audio

output.

Palmrest

Comfortable support area for your hands

when you use the computer.

Closed Front View

Icon

Item

Description

Power indicator

Indicates the computer’s power status.

Battery indicator

Indicates the computer’s battery status.

Line-in jack

Accepts audio line-in devices (e.g., audio

CD player, stereo walkman).

Microphone-in jack

Accepts input from external microphones.

Connects to audio line-out devices (e.g.,

Headphones/speaker/

line-out jack with S/PDIF speakers, headphones).

support

Infrared port

Interfaces with infrared devices (e.g.

infrared printer and IR-aware computer).

Chapter 1

Left View

Icon

Item

Description

Kensington lock slot

Connects to a Kensington-compatible

computer security lock.

External display (VGA)

port

Connects to a display device (e.g., external

monitor, LCD projector).

DVI-D port

Supports digital video connections.

DVI

Ethernet (RJ-45)

Connects to an Ethernet 10/100/1000-

based network (for selected models).

2 USB 2.0 port

Connect to USB 2.0 devices (e.g., USB

mouse, USB camera).

S-video/TV-out (NTSC/ Connects to a television or display device

PAL) port

with S-video input.

4-pin IEEE 1394 port

Connects to IEEE 1394 devices.

Volume control

Increases and decreases the volume.

5-in-1 card reader

Accepts Secure Digital (SD),

MultiMediaCard (MMC), Memory Stick

(MS), Memory Stick PRO (MS PRO), xD-

Picture Card (xD).

PCI Express Card slot

Accepts an Express Card/54 module.

Note: Express Cards are third generation

of PC cards, hot-swapable and maller than

previous PC Cards. Designed for both

desktop and mobile use, Express Cards

use either USB 2.0 or a single lane PCI

Express technology that provides 500

Mbytes/sec total throughput. Formerly

code named “NEWCARD,” Express Cards

are 5mm thick like Type II PC Cards, but do

not use the same 86x54mm footprint.

Express Cards come in 75x54mm and

75x34mm sizes. Express Card/54 slot

means this notebook accepts 75x54mm

Express Cards.

Chapter 1

Right View

Icon

Item

Description

2 USB 2.0 ports

Connect to USB 2.0 devices (e.g., USB

mouse, USB camera).

AV-in port

Accepts input signals from audio/video

(AV) devices.

Optical drive

Internal optical drive; accepts CDs or DVDs

(slot-load or tray-load depending on

model).

Optical disk access

indicator

Lights up when the optical drive is active.

Optical drive eject

button

Ejects the optical disk from the drive.

Emergency eject hole

Ejects the optical drive tray when the

computer is turned off.

Modem (RJ-11) port

Connects to a phone line.

RF-in port

Accepts input signals from analog/digital

TV-tuner devices (for selected models).

Rear view

Icon

Item

Description

DC-in jack

Connects to an AC adapter.

Ventilation slots

Enable the computer to stay cool, even

after prolonged use.

Chapter 1

Base view

Item

Battery bay

Description

Houses the computer’s battery pack.

Battery release latch

Battery lock

Releases the battery for removal.

Locks the battery in position.

Hard disk bay

Houses the computer’s hard disk (secured with screws)

Ventilation slots and

cooling fan

Enable the computer to stay cool, even after prolonged use.

Note: Do not cover or obstruct the opening of the fan.

Indicators

The computer has several easy-to-read status indicators.

The front panel indicators are visible even when the computer cover is closed up.

Chapter 1

Icon

Function

Power

Description

Lights up when the computer is on.

Battery

Lights up when the battery is being charged.

Wireless LAN

Bluetooth

Indicates the status of wireless LAN communication.

Indicates the status of Bluetooth communication.

HDD

Indicates when the hard disc or optical drive is active.

Lights when Num Lock is activated.

Num lock

Cap lock

Lights when Cap Lock is activated

NOTE: 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows

green when in AC mode.

Easy-Launch Buttons

To the top of the keyboard there are four easy-launch buttons: Web browser, mail, arcade buttons and an

Empowering Key “

Press “ “ to run the Acer Empowering Technology. The mail and Web browser buttons are pre-set to email

and Internet programs, but can be reset by users. To set the Web browser and mail buttons, run the Launch

Manager.

Chapter 1

Launch Button

Default application

Acer Empowering Technology (user-programmable)

Web browser

Internet browser (user-programmable)

Email application (user-programmable)

Windows Media Center

Mail

Arcade

Touchpad Basics

The following teaches you how to use the touchpad:

Move your finger across the touchpad (2) to move the cursor.

Press the left (1) and right (4) buttons located beneath the touchpad to perform selection and

execution functions. These two buttons are similar to the left and right buttons on a mouse.

Tapping on the touchpad is the same as clicking the left button.

The center (3) button to mimics your cursor pressing on the right scroll bar of Windows

applications.

Function

Left Button (1)

Right Button (4)

Main touchpad (2)

Center button (3)

Execute

Click twice quickly

Tap twice (at the

same speed as

double-clicking the

mouse button)

Select

Drag

Click once

Tap once

Click and hold, then

use finger on the

touchpad to drag

the cursor.

Tap twice (at the

same speed as

double-clicking a

mouse button); rest

your finger on the

touchpad on the

second tap and

drag the cursor.

Access context

Click once

Scroll

Click and hold to

move up/down/left/

right.

NOTE: When using the touchpad, keep it - and your fingers - dry and clean. The touchpad is sensitive to finger

movements; hence, the lighter the touch, the better the response. Tapping too hard will not increase the

touchpad’s responsiveness.

Chapter 1

Using the Keyboard

The keyboard has full-sized keys and an embedded keypad, separate cursor keys, one Windows key and

twelve function keys.

Lock Keys and embedded numeric keypad

The keyboard has three lock keys which you can toggle on and off.

Lock Key

Description

Caps Lock

When Caps Lock is on, all alphabetic characters typed

are in uppercase.

Num lock

When Num Lock is on, the embedded keypad is in

<Fn>+<F11> numeric mode. The keys function as a calculator

(complete with the arithmetic operators +, -, *, and /).

Use this mode when you need to do a lot of numeric

data entry. A better solution would be to connect an

external keypad.

Scroll lock

When Scroll Lock is on, the screen moves one line up

<Fn>+<F12> or down when you press the up or down arrow keys

respectively. Scroll Lock does not work with some

applications.

The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters

located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols

are not printed on the keys.

Desired Access

Num Lock On

Num Lock Off

Number keys on embedded Type numbers in a normal

keypad

manner.

Cursor-control keys on

embedded keypad

Hold <Shift> while using

cursor-control keys.

Hold <Fn> while using

cursor-control keys.

Main keyboard keys

Hold <Fn> while typing

letters on embedded

keypad.

Type the letters in a normal

manner.

Windows Keys

The keyboard has one key that performs Windows-specific functions.

Chapter 1

Key

Icon

Description

Windows key

Pressed alone, this key has the same effect as

clicking on the Windows Start button; it launches the

Start menu. It can also be used with other keys to

provide a variety of function:

+ <Tab> Activates next taskbar button.

+ <E> Opens the My Computer window

+ <F1> Opens Help and Support.

+ <F> Opens the Search: All Files dialog box.

+ <R> Opens the Run dialog box.

<M> Minimizes all windows.

<Shift>+

action.

+ <M> Undoes the minimize all windows

This key has the same effect as clicking the right

mouse button; it opens the application’s context

menu.

Application key

Hot Keys

The computer employs hotkeys or key combinations to access most of the computer’s controls like screen

brightness, volume output, and the BIOS utility.

To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.

Hot Key

Icon

Function

Hot key help

Description

Displays help on hot keys.

Acer eSettings

Launches the Acer eSettings in Acer eManager.

Acer ePower

Management

Launches the Acer ePower Management in Acer

Empowering Technology. See “Acer Empowering

Technology” on page 18.

Sleep

Puts the computer in Sleep mode.

Chapter 1

Hot Key

Icon

Function

Description

Display toggle

Switches display output between the display screen,

external monitor (if connected) and both.

Screen blank

Turns the display screen backlight off to save power.

Press any key to return.

Touchpad toggle

Speaker toggle

Brightness up

Brightness down

Turns the internal touchpad on and off.

Turns the speakers on and off.

Increases the screen brightness.

Decreases the screen brightness

Play/Pause

Stop

Plays or pauses the media.

Stops the media playing.

Returns to previous media file.

Jumps to next media file.

Special Key

You can locate the Euro symbol and US dollar sign at the upper-center and/or bottom-right of your keyboard.

To type:

The Euro symbol

1. Open a text editor or word processor.

2. Either directly press the < > symbol at the bottom-right of the keyboard, or hold <Alt Gr> and then

press the<5> symbol at the upper-center of the keyboard.

NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/

typography/faq/faq12.htm for more information.

Chapter 1

The US dollar sign

1. Open a text editor or word processor.

2. Either directly press the < > key at the bottom-right of the keyboard, or hold <Shift> and then press the

<4> key at the upper-center of the keyboard.

NOTE: This function varies by the operating system version.

Chapter 1

Hardware Specifications and Configurations

Processor

Item

Specification

Intel® Celeron (Santarosa) processor

Intel® GL960 Express chipset

Intel socket 1466pin FCBGA

0.944~1.3V

CPU type

Core logic

CPU package

CPU core voltage

CPU Fan True Value Table

Test Condition: 35W@Ambient 35 degree

CPU Temperature

Fan Speed

(rpm)

2600

SPL Spec

Core 0

Core 1

(dBA)

2900

3400

3600

100

3600

BIOS

Item

Specification

BIOS vendor

BIOS Version

BIOS ROM type

BIOS ROM size

BIOS package

Supported protocols

Insyde

Macronix_MX25L8005/ EON_EN25F80

1M bytes

SPI Flash part

ACPI 1.0b/2.0/3.0, PCI 2.2, System/HDD Password Security

Control, INT13h Extensions, PnP BIOS 1.0a, SMBIOS 2.4, Simple

Boot Flag 1.0, Boot Block, PCI Bus Power Management Interface

Specification, USB1.1/2.0, IEEE 1394 1.0, USB/1394 CD-ROM

Boot Up support, PC Card 95 (PCMCIA 3.0 Compliant Device),

IrDA 1.0, Intel AC97 CNR Specification, WfM 2.0, PXE (Preboot

Execution Environment), BIS 1.0 (Boot Integrity Service

Application Program Interface), PC99a and Mobile PC2001

Compliant, Intel Enhanced SpeedStep Technology

BIOS password control

Set by setup manual

Cache

Item

Specification

Built-in CPU

Cache controller

Cache size

2MB

1st level cache control

2st level cache control

Cache scheme control

System Memory

Item

Always enabled

Fixed in write-back

Specification

Memory controller

Built-in

Chapter 1

Item

Specification

0MB (no on-board memory)

Memory size

DIMM socket number

2 sockets

Supports memory size per socket

Supports maximum memory size

Supports DIMM type

2 GB

4G for 64bit OS (with two 2GB SODIMM)

DDR 2 Synchronous DRAM

667/800 MHz

Supports DIMM Speed

Supports DIMM voltage

1.8V and 0.9V

Supports DIMM package

Memory module combinations

200-pin soDIMM

You can install memory modules in any combinations as long as

they match the above specifications.

Memory Combinations

Slot 1

Slot 2

Total Memory

0MB

256MB

512MB

1024MB

2048MB

256MB

512MB

1024MB

2048MB

256MB

512MB

1024MB

2048MB

0MB

256MB

512MB

0MB

1024MB

2048MB

512MB

0MB

256MB

768MB

256MB

1280MB

2304MB

768MB

256MB

512MB

1024MB

1536MB

2560MB

1024MB

1280MB

1536MB

2048MB

3072MB

2048MB

2304MB

2560MB

3072MB

4096MB

512MB

1024MB

2048MB

256MB

512MB

1024MB

2048MB

0MB

256MB

512MB

1024MB

2048MB

NOTE: Above table lists some system memory configurations. You may combine DIMMs with various

capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be

reversed.

Chapter 1

LAN Interface

Item

Specification

Chipset

Atheros / Broadcom

Supports LAN protocol

Features

10/100/1000 Ethernet Giga LAN

PCI-E Giga LAN

Support Wake-On-Lan (AC mode S5)

No ASF 2.0/iAMT 4.0

Wireless Module 802.11b/g

Item

Specification

Chipset

Intel Shirley Peak and Echo Peak (for Centrino platform)

Atheros WLAN XB63 and Broadcom WLAN BCM4312 (for

Non-Centrino)

Data throughput

Protocol

11~54 Mbps, up to 270 Mbps for Draft-N

802.11b+g, Draft-N

Interface

PCI bus (mini PCI socket for wireless module)

Hard Disk Drive Interface

Item

Data heads

3 (for Hitachi and

Seagate) 4 (for

Toshiba)

4 (for Hitachi) 3

(for Seagate)

Drive Format

Disks

Spindle speed

(RPM)

5400 RPM

4200 RPM

Performance

Specifications

Buffer size

Interface

2048KB

8192KB

ATA/ATAPI-6;

ATA-6

ATA/ATAPI-6;

ATA-6

ATA/ATA-6; ATA-

Max. media

transfer rate

(disk-buffer,

Mbytes/s)

372

350

Data transfer rate

(host~buffer,

Mbytes/s)

100 MB/Sec.

Ultra DMA mode-

100 MB/Sec.

Ultra DMA mode-

100 MB/Sec.

Ultra DMA mode-

100 MB/Sec.

Ultra DMA mode-

DC Power

Requirements

Voltage tolerance

5V(DC) +/- 5%

Combo Drive Module

Item

Specification

Vendor & model name

HLDS COMBO 12.7mm Tray 24X GCC-T10N SONY COMBO 12.7mm

Tray 24X CRX880A LF PIONEER Super-Multi Drive 12.7mm Tray DVR-

K17RS PANASONIC Super-Multi Drive 12.7mm Tray DL 8X UJ-850

PHILIPS Super-Multi Drive 12.7mm Tray DL 8X DS-8A1P HLDS Super-

Multi Drive 12.7mm Tray LabelFlash 8X GSA-T20N SONY Super-Multi

Drive 12.7mm Tray DL 8X AD-7530A TOSHIBA HD-DVD Drive 12.7mm

Tray TS-L802A

Chapter 1

Item

Specification

With CD Diskette

Performance Specification

Transfer rate (KB/sec)

With DVD Diskette

Sustained: Max 3.6Mbytes/

sec

Sustained: Max 10.8Mbytes/sec

Buffer Memory

Interface

2MB

Enhanced IDE(ATAPI) compatible

Applicable disc format

Support disc formats 1. Reads data in each CD-ROM, CD-ROM XA, CD-

1, Video CD, CD-Extra and CD-Text 2. Reads data in Photo CD (single

and Multi-session) 3. Reads standard CD-DA 4. Reads and writes CD-R

discs 5. Reads and writes CD-RW discs 6. Reads and writes in each

DVD+R/RW (Ver. 1.1) 7. Reads data in each DVD-ROM and DVD-R (Ver.

2.0 for Authoring) 8. Reads and writes in each DVD-R (Ver. 2.0 for

general), DVD-RW and DVD+R/RW (Ver1.1)

Loading mechanism

Load: Manual

Release:

(a) Electrical Release (Release Button)

(b) Release by ATAPI command

Power Requirement

Input Voltage

5 V +/- 5 % (Operating)

Audio Interface

Item

Specification

Realtek ALC268

Audio Controller

Audio onboard or optional

Mono or Stereo

Built-in

Stereo

Resolution

18 bit stereo full duplex

HD audio Interface;

1Hz resolution VSR (Variable Sampling Rate)

Yes

Compatibility

Sampling rate

Internal microphone

Internal speaker / Quantity

Supports PnP DMA channel

Supports PnP IRQ

Yes/2(1.5W speakers)

DMA channel 0 DMA channel 1

IRQ10, IRQ11

USB Interface

Item

Specification

Chipset

ICH8M

USB Compliancy Level

OHCI

2.0

USB 1.1 and USB 2.0 Host controller

Number of USB port

Location

Two in stack one by single

Enable/Disable by BIOS Setup

Serial port function control

PCMCIA Port

Item

Specification

PCMCIA controller

TI PCI 7412

Chapter 1

Item

Specification

Supports card type

Number of slots

Access location

Type-II

One type-II

Left side

No ZV support

Yes

Supports ZV (Zoomed Video) port

Supports 32 bit CardBus

System Board Major Chips

Item

Controller

Core logic

Intel® 965PM/965GM+ICH8M

Broadcom 5787

LAN

USB 2.0

Built in ICH8M

Super I/O controller

Wireless LAN

NS 87383

Foxconn Atheros XB63 minicard b/g Fox BRM 4311

Minicard BG

PCMCIA

Audio

TI PCI 7412

Realtek ALC268

Keyboard

Item

Specification

Keyboard controller

Total number of keypads

Windows logo key

KBC1122

88-/89-key

Yes

Internal & external keyboard work

simultaneously

Plug USB keyboard to the USB port directly: Yes

Battery

Item

Specification

Vendor & model name

BATTERY PANASONIC LI-ION

6CELLS BATTERY SANYO LI-

ION 6CELLS BATTERY

SIMPLO LI-ION 6CELLS

BATTERY SONY LI-ION

6CELLS BATTERY

PANASONIC LI-ION 8CELLS

BATTERY SANYO LI-ION

8CELLS BATTERY SIMPLO LI-

ION 8CELLS BATTERY SONY

LI-ION 8CELLS

Battery Type

Li-ion

4400 mAh

Pack capacity

Number of battery cell

Package configuration

3 cells in series, 2 series in

parallel

Normal voltage

Charge voltage

11.1V (Panasonic 10.8V)

12.6V

Chapter 1

LCD 15.4”

Specificatio

Item

Vendor & model name

LPL

LP154WX4TL

B2 (G)

CMO

N154I2L05

GLARE

AUO

B154EW0

2 V7(G)

SAMSUNG

LTN154AT010

01(G)

Screen Diagonal (mm)

Active Area (mm)

Display resolution (pixels)

Pixel Pitch

15.4 inches

15.4

inches

15.4 inches

304.1x228.1

304.1x228

1440x900

WXGA+

1440x900

WXGA+

1440x900

WXGA+

1440x900

WXGA+

0.297x0.297

0.099x0.297

0.297x0.2

Pixel Arrangement

R.G.B. Vertical

Stripe

R.G.B.

Vertical

Stripe

R.G.B.

Vertical

Stripe

R.G.B.Vertical

Stripe

Display Mode

Normally

White

Normally

White

Normally

White

Normally

White

Typical White Luminance (cd/m2)

also called Brightness

300

Luminance Uniformity

Contrast Ratio

N/A

300

N/A

300

250

Response Time (Optical Rise Time/

Fall Time)msec

Nominal Input Voltage VDD

Typical Power Consumption (watt)

Weight

+3.3V Typ.

5.6/5.7

550

+3.3V

3.96

570

3.3V

N/A

600

3.3V

N/A

600

Physical Size(mm)

317.3x242.0x6

. 0

317.3x242.0

x5. 9

317.3x242

.0x6. 5

317.3x242.0x

6. 5

Electrical Interface

Support Color

1 channel

LVDS

1 channel

LVDS

1 channel

LVDS

1 channel

LVDS

262K colors

(RGB 6-bit

data driver)

262,144

Viewing Angle (degree) Horizontal:

Right/Left Vertical: Upper/Lower

40/40 10/30

45/45 15/35

40/40 20/

40/40 20/40

Temperature Range( C) Operating

Storage (shipping) °

0 to +50 -20 to

+60

0 to +50 -25

to +60

0 to +50 -

20 to +60

0 to +50 -20 to

+60

Chapter 1

LCD Inverter

Item

Specification

Darfon/V189-301GP

Vendor & model name

Brightness conditions

Input voltage (V)

N/A

9~21

Input current (mA)

2.56 (max)

780V (2000V for kick off)

6.5 (max)

Output voltage (V, rms)

Output current (mA, rms)

Output voltage frequency (k Hz)

65K Hz (max)

AC Adapter

Item

Input rating

Specification

100~240Vac/ 65Hz

1.75A

Maximum input AC current

Inrush current

220A@115VAC

220A@230VAC

Efficiency

82% min. @115VAC input full load

System Power Management

ACPI mode

Power Management

Mech. Off (G3)

All devices in the system are turned off completely.

Soft Off (G2/S5)

OS initiated shutdown. All devices in the system are turned

off completely.

Working (G0/S0)

Individual devices such as the CPU and hard disk may be

power managed in this state.

Suspend to RAM (S3)

CPU set power down

VGA Suspend

PCMCIA Suspend

Audio Power Down

Hard Disk Power Down

CD-ROM Power Down

Super I/O Low Power mode

Save to Disk (S4)

Also called Hibernation Mode. System saves all system

states and data onto the disc prior to power off the whole

system.

Chapter 1

System Power Management

ACPI mode

Power Management

Working (G0/S0)

Individual devices such as the CPU and hard disc may be power

managed in this state.

Suspend to RAM (S3)

CPU set power down

VGA Suspend

PCMCIA Suspend

Audio Power Down

Hard Disk Power Down

CD-ROM Power Down

Super I/O Low Power mode

Save to Disk (S4)

Also called Hibernation Mode. System saves all system states and

data onto the disc prior to power off the whole system.

Chapter 1

Chapter 2

System Utilities

BIOS Setup Utility

The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/

Output System).

Your computer is already properly configured and optimized, and you do not need to run this utility. However, if

you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4

Troubleshooting when problem arises.

To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is prompted

on the bottom of screen).

Press m to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change

boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.

Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without

entering BIOS SETUP Utility.

InsydeH2O Setup Utility

Main

Security

Advanced

Boot

Exit

Information

Intel (R) Core(TM)2 Duo CPU

2.00 GHz

T7300

CPU Type :

CPU Speed :

HDD Model Name :

HDD Serial Number :

ATAPI Model Name :

ATAPI Serial Number:

Hitachi HTS541616J9SA00

xxxxxxxxxxxxxxxxxxxxxx

TOSHIBA DVDW/HD TS-L802A

xxxxxxxxxxxxxxxxxxxxxx

System BIOS Version: V0.18.T04

ATI

VGA BIOS Version:

Serial Number:

Asset Tag Number:

Product Name:

Manufacturer Name:

UUID:

xxxxxxxxxxxxxxxxxxxxxx

Acer

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

F1 Help

Esc Exit

Select Item

F5/F6 Change Values

Enter Select Sub-Menu

F9 Setup Defaults

F10 Save and Exit

Select Menu

Chapter 2

Navigating the BIOS Utility

There are six menu options: Info., Main, System Devices, Security, Boot, and Exit.

Follow these instructions:

To choose a menu, use the cursor left/right keys (zx).

To choose a parameter, use the cursor up/down keys (wy).

To change the value of a parameter, press por q.

A plus sign (+) indicates the item has sub-items. Press e to expand this item.

Press ^ while you are in any of the menu options to go to the Exit menu.

In any menu, you can load default settings by pressing t. You can also press u to save any

changes made and exit the BIOS Setup Utility.

NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a

particular menu are shown on the bottom of the screen. Help for parameters are found in the Item

Specific Help part of the screen. Read this carefully when making changes to parameter values. Please

note that system information is subject to different models.

Chapter 2

Information

InsydeH2O Setup Utility

Security Advanced

Main

Boot

Exit

Information

Intel (R) Core(TM)2 Duo CPU

2.00 GHz

T7300

CPU Type :

CPU Speed :

HDD Model Name :

Hitachi HTS541616J9SA00

xxxxxxxxxxxxxxxxxxxxxx

TOSHIBA DVDW/HD TS-L802A

xxxxxxxxxxxxxxxxxxxxxx

HDD Serial Number :

ATAPI Model Name :

ATAPI Serial Number:

System BIOS Version: V0.18.T04

ATI

VGA BIOS Version:

Serial Number:

Asset Tag Number:

Product Name:

Manufacturer Name:

UUID:

xxxxxxxxxxxxxxxxxxxxxx

Acer

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

F1 Help

Esc Exit

Select Item

F5/F6 Change Values

Enter Select Sub-Menu

F9 Setup Defaults

F10 Save and Exit

Select Menu

NOTE: The system information is subject to different models.

Parameter

CPU Type / CPU Speed

HDD Model Name

Description

This field shows the CPU type and speed of the system.

This field shows the model name of HDD installed on primary IDE master.

This field displays the serial number of HDD installed on primary IDE master.

HDD Serial Number

ATAPI Model Name

This field shows the model name of devices installed on secondary IDE master. The hard

disk drive or optical drive model name is automatically detected by the system.

ATAPI Serial Number

This field displays the serial number of devices installed on secondary IDE master. The

hard disk drive or optical drive model name is automatically detected by the system.

System BIOS Version

VGA BIOS Version

Serial Number

Displays system BIOS version.

This field displays the VGA firmware version of the system.

This field displays the serial number of this unit.

This field displays the asset tag number of the system.

This field shows product name of the system.

This field displays the manufacturer of this system.

Asset Tag Number

Product Name

Manufacturer Name

UUID Number

This will be visible only when an internal LAN device is presenting.

UUID=32bytes

Chapter 2

Main

The Main screen displays a summary of your computer hardware information, and also includes basic setup

parameters. It allows the user to specify standard IBM PC AT system parameters.

InsydeH2O Setup Utility

Information

Main

Security

Advanced

Boot

Exit

Item Specific Help

System Time:

System Date :

[19:03:49]

[04/25/2007]

This is the help for the hour

field. Valid range is from 0

to 23.

Shows system base memory size

System Memory :

Total Memory :

Video Memory :

640 KB

INCREAE/REDUCE : F5/ F6.

1023 MB Shows extended memory size

[256MB]

Quiet Boot :

[Enabled]

[Disabled]

[Enabled]

[Disabled]

Network Boot :

F12 Boot Menu :

D2D Recovery :

Wake-up on LAN :

F1 Help

Exit

Select Item

Select Menu

F5/F6 Change Values

Enter Select

F9 Setup Defaults

Esc

Sub-Menu

F10 Save and Exit

NOTE: The screen above is for your reference only. Actual values may differ.

Chapter 2

The table below describes the parameters in this screen. Settings in boldface are the default and suggested

parameter settings.

Parameter

System Time

Description

Format/Option

Format: HH:MM:SS

Sets the system time. The hours are displayed

with 24-hour format.

(hour:minute:second) System Time

System Date

Sets the system date.

Format MM/DD/YYYY (month/day/

year) System Date

System Memory

Total Memory

This field reports the memory size of the system.

Memory size is fixed to 640MB

This field reports the total memory size in the

system.

Video Memory

Quiet Boot

Shows the Video memory size.

Determines if Customer Logo will be displayed or

not; shows Summary Screen is disabled or

enabled.

Option: Enabled or Disabled

Enabled: Customer Logo is displayed, and

Summary Screen is disabled.

Disabled: Customer Logo is not displayed, and

Summary Screen is enabled.

Network Boot

Enables, disables the system boot from LAN

(remote server).

Option: Enabled or Disabled

F12 Boot Menu

D2D Recovery

Enables, disables Boot Menu during POST.

Option: Disabled or Enabled

Enables, disables D2D Recovery function. The

function allows the user to create a hidden

partition on hard disc drive to store operation

system and restore the system to factory

defaults.

Option: Enabled or Disabled

Wake-up on LAN

Enables, disables remote wakeup (power on) via

LAN.

Option: Disabled or Enabled

NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is

because the user is not allowed to control the settings in these cases.

Chapter 2

Advanced

The Advanced screen displays advanced settings in BIOS.

InsydeH2O Setup Utility

Security Advanced Boot

Information

Main

Exit

Item Specific Help

Advanced CPU Control

Platform Power Management

IDE Configuration

These items control

various CPU parameters.

ACPI S1:

[Enabled]

ACPI S3:

[Enabled]

[Disabled]

Auto wake on S5

Crestline PM Support

POPUP Support

POPDOWN Support

DeepC4

[Enabled]

Hard C4E

F1 Help

Select Item

Select Menu

F5/F6 Change Values

Enter Select

F9 Setup Defaults

Exit

Esc

Sub-Menu

F10 Save and Exit

The table below describes the parameters in this screen. Settings in boldface are the default and suggested

parameter settings.

Parameter

Advanced CPU Control

Platform Power Management

IDE Configuration

ACPI S1

Description

Option

Sets the ACPI S1 sleep state.

Sets the ACPI S3 sleep state.

Enabled or Disabled

ACPI S3

Enabled or Disabled

Auto wake on S5

Enables the Auto wake on S5 by day of month

or fixed time of every day, or disables this

feature.

Disabled, By Every Day, or

By Day of Month

Crestline PM Support

Enables, disables Calistoga Enhanced Power

Management mode.

Enabled or Disabled

POPUP Support

POPDOWN Support

DeepC4

Enabled or Disabled

Hard C4E

Chapter 2

Security

The Security screen contains parameters that help safeguard and protect your computer from unauthorized

use.

InsydeH2O Setup Utility

Security Advanced

Information

Main

Boot

Exit

Item Specific Help

Supervisor Password Is

User Password Is

HDD Password

Clear

Install or Change the

password.

Set Supervisor Password

Set User Password

Set HDD Password

[Enter]

[Enabled]

Password on Boot :

F1 Help

Esc Exit

Select Item

Select Menu

F5/F6 Change Values

Enter Select Sub-Menu

F9 Setup Defaults

F10 Save and Exit

Chapter 2

The table below describes the parameters in this screen. Settings in boldface are the default and suggested

parameter settings.

Parameter

Supervisor Password is

User Password is

Description

Option

Clear or Set

Shows the setting of the Supervisor password

Shows the setting of the user password.

Shows the setting of the hard disk password.

Clear or Set

HDD Password

Clear or Set

Set Supervisor Password

Press Enter to set the supervisor password.

When set, this password protects the BIOS

Setup Utility from unauthorized access. The

user can not either enter the Setup menu nor

change the value of parameters.

Set User Password

Press Enter to set the user password. When

user password is set, this password protects

the BIOS Setup Utility from unauthorized

access. The user can enter Setup menu only

and does not have right to change the value of

parameters.

Set HDD Password

Password on Boot

Press Enter to set the hard disk password.

When set, this password protects the BIOS

Setup Utility from unauthorized access. The

user can not either enter the Setup menu nor

change the value of parameters.

Defines whether a password is required or not

while the events defined in this group

happened. The following sub-options are all

requires the Supervisor password for changes

and should be grayed out if the user password

was used to enter setup.

Disabled or Enabled

NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget

your password. If you forget your password, you may have to return your notebook computer to your

dealer to reset it.

Setting a Password

Follow these steps as you set the supervisor, user, or hard disk password:

1. Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The

Set Supervisor Password box appears:

2. Type a password in the “Enter New Password” field. The password length can not exceed 8 alphanumeric

characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New Password” field.

IMPORTANT: Be very careful when typing your password because the characters do not appear on the

screen.

3. Press e. After setting the password, the computer sets the Supervisor Password parameter to “Set”.

4. If desired, you can opt to enable the Password on boot parameter.

5. When you are done, press u to save the changes and exit the BIOS Setup Utility.

Chapter 2

Removing a Password

Follow these steps:

1. Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The

Set Supervisor Password box appears:

2. Type the current password in the Enter Current Password field and press e.

3. Press e twice without typing anything in the Enter New Password and Confirm New Password fields.

The computer then sets the Supervisor Password parameter to “Clear”.

4. When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.

Changing a Password

1. Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The

Set Supervisor Password box appears:

2. Type the current password in the Enter Current Password field and press e.

3. Type a password in the Enter New Password field. Retype the password in the Confirm New Password

field.

4. Press e. After setting the password, the computer sets the Supervisor Password parameter to “Set”.

5. If desired, you can enable the Password on boot parameter.

6. When you are done, press u to save the changes and exit the BIOS Setup Utility.

If the verification is OK, the screen will display as following.

The password setting is complete after the user presses u.

Chapter 2

If the current password entered does not match the actual current password, the screen will show you the

Setup Warning.

If the new password and confirm new password strings do not match, the screen will display the following

message.

Chapter 2

Boot

This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices

includes the diskette drive in module bay, the onboard hard disk drive, and the CD-ROM in module bay.

InsydeH2O Setup Utility

Information

Main

Security

Advanced

Boot

Exit

Item Specific Help

Boot Priority Order:

Use < > or < > to select a

device, then press <F5> to

move it up the list, or <F6>

to move it down the list.

Press <Esc> to escape the

menu.

1: IDE 0 : Hitachi HTS541616J9SA00

2: IDE 1 : TOSHIBA DVDW/HD TS-L802A

3: USB FDD :

4: Network Boot : MBA v9.4.5 Slot 0400

5: USB HDD :

6: USB KEY :

7: USB CDROM :

F1 Help

Exit

Select Item

F5/F6 Change Values

Enter Select

F9 Setup Defaults

Select Menu

Esc

Sub-Menu

F10 Save and Exit

Chapter 2

Exit

The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.

InsydeH2O Setup Utility

Security Advanced Boot

Information

Main

Exit

Item Specific Help

Exit Saving Changes

Exit Discarding Changes

Load Setup Defaults

Discard Changes

Exit System Setup and

save your changes to

CMOS.

Save Changes

F1 Help

Exit

Select Item

Select Menu

F5/F6 Change Values

Enter Select Sub-Menu

F9 Setup Defaults

F10 Save and Exit

Esc

The table below describes the parameters in this screen.

Parameter

Description

Exit Saving Changes

Exit Discarding Changes

Load Setup Defaults

Discard Changes

Exit System Setup and save your changes to CMOS.

Exit utility without saving setup data to CMOS.

Load default values for all SETUP item.

Load previous values from CMOS for all SETUP items.

Save Setup Data to CMOS.

Save Changes

Chapter 2

BIOS Flash Utility

The BIOS flash memory update is required for the following conditions:

New versions of system programs

New features or options

Restore a BIOS when it becomes corrupted.

Use the Phlash utility to update the system BIOS flash ROM.

NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery

Diskette before you use the Phlash utility.

NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.

NOTE: Please use the AC adapter power supply when you run the Phlash utility. If the battery pack does not

contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not

completely loaded.

Follow the steps below to run the Phlash.

1. Prepare a bootable diskette.

2. Copy the flash utilities to the bootable diskette.

3. Then boot the system from the bootable diskette. The flash utility has auto-execution function.

Chapter 2

Chapter 3

Machine Disassembly and Replacement

This chapter contains step-by-step procedures on how to disassemble the notebook computer for

maintenance and troubleshooting.

To disassemble the computer, you need the following tools:

Wrist grounding strap and conductive mat for preventing electrostatic discharge

Small Philips screw driver

Philips screwdriver

Plastic flat head screw driver

Tweezers

NOTE: The screws for the different components vary in size. During the disassembly process, group the

screws with the corresponding components to avoid mismatch when putting back the components.

When you remove the stripe cover, please be careful not to scrape the cover.

Chapter 3

General Information

Before You Begin

Before proceeding with the disassembly procedure, make sure that you do the following:

1. Turn off the power to the system and all peripherals.

2. Unplug the AC adapter and all power and signal cables from the system.

3. Remove the battery pack.

Chapter 3

Disassembly Procedure Flowchart

The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence

and instructs you on the components that need to be removed during servicing. For example, if you want to

remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in

that order.

Start

Battery Pack

D*5

F*1

F*2

Thermal

Door

Mimi Cover

HDD Door

B*1

D*1

F*1

H*4

System Fan

ODD Module

Memory

HDD Bracket

HDD

B*4

Thermal

Module

Middle Cover

F*2

CPU

Keyboard

C*2 LCD hinges to logic

D*2 LCD hinges to logic

C*2 on bottom side

LCD Module

C*8 upper case assembly to lower case assembly on bottom side

C*2 upper case assembly to lower case assembly on upper side

Lower Case

Assembly

Upper Case

Assembly

F*1

Modem

Board

F*2

Media Board

(for AS

F*1

Switch Board

(for AS

models)

Touchpad

Bracket

models)

F*1

Main Board

Touchpad

FFC

Touchpad

F*2

Lower Case

Speaker Set

Chapter 3

LCD Module

B*4

LCD Bezel

G*1 for 15"

G*2 for 15.4"

LCD Inverter

B*2

LCD

Assembly

LCD Panel

G*2 for 15.4"

Wireless

Antenna Set

F*8 (4 on left; 4 on right)

LCD Bracket

LCD Cable

Sets

LCD

Screw List

Item

Description

SCREW M2.5*3(NL)

Part Number

86.TAVV5.001

86.TAVV5.002

86.TAVV5.003

86.TAVV5.004

86.TAVV5.005

86.TAVV5.006

86.TAVV5.007

86.TAVV5.008

86.TAVV5.009

SCREW M2.5*6(NL)

SCREW M2.5*10(NL)

SCREW M2.5*15(NL)

SCREW M2*2.2

SCREW M2*3(NL)

SCREW M2*4

SCREW M3*4(NL)

SCREW D-SUB 4#X40* 1/5-NI (NL)

Chapter 3

Removing the Battery Pack

1. Unlock the battery lock (move the battery lock to the unlock position as shown).

2. Slide the battery release latch then remove the battery.

Chapter 3

Removing the HDD Module/Memory/Wireless LAN Card/Modem Card/

TV Tuner Card/System Fan/Thermal Modules/VGA Board/CPU/

Keyboard and the LCD Module

Removing the HDD Module

1. Remove the two screws fastening the HDD cover.

2. Detach the HDD cover from the main unit.

3. Pull the tab to remove the HDD module in the direction of the arrow.

Removing the Memory

1. Remove the four screws holding the thermal cover.

2. Detach the thermal cover from the main unit.

3. Pop out the memory from the DIMM socket then remove it (If the notebook has two memory, then repeat

this step).

Removing the Wireless LAN Card/Modem Card and TV Tuner Card

1. Disconnect the three antennae from the wireless LAN card.

2. Remove the two screws fastening the wireless LAN card.

3. Then take out the wireless LAN card from the main unit.

Chapter 3

4. Remove the screw fastening the modem card and detach the modem card from the main board.

5. Disconnect the RJ-11 cable and remove the modem card.

6. Disconnect the RF cable from the TV tuner card.

7. Remove the two screws fastening the TV tuner card.

8. Then take out the TV tuner card from the main unit.

NOTE: TV tuner card on selected models only.

Chapter 3

Removing the System Fan/Thermal Modules/VGA Board and CPU

1. Disconnect the fan cable from the main board.

2. Remove the three screws holding the system fan.

3. Remove the four spring screws holding the CPU thermal module.

4. Then detach the CPU thermal module as shown.

5. Remove the four spring screws holding the VGA thermal module.

6. Then detach the VGA thermal module as shown.

7. Remove the two screws fastening the VGA board then remove it.

8. Use a flat screwdriver to release the CPU lock (Turn counter clock-wire).

9. Remove the CPU from the CPU socket carefully.

NOTE: VGA thermal module and VGA board on selected models only.

Chapter 3

Removing the Keyboard and LCD Module

1. Turn the notebook over.

2. Remove the two screws securing the strip cover from the bottom of the notebook.

3. Detach the strip cover from the front side and remove it.

4. Gently pull up the keyboard to release it from the four snaps as shown.

5. Turn over the keyboard as the image shows. Then disconnect the keyboard cable from the main board.

6. Remove the keyboard from the main unit.

7. Disconnect the LCD cable and microphone cable from the main board.

8. Pull out the wireless LAN antennas free from the main unit as shown.

9. Remove the four screws securing the hinges.

Chapter 3

10. Detach the LCD module from the main unit.

Chapter 3

Disassembling the Main Unit

Separate the Main Unit Into the Upper and the Lower Case Assembly

1. Remove the screw fastening the ODD from the bottom of the notebook.

2. Push the ODD module outwards and gently pull it out as shown.

3. Press and release the PC dummy card from the PC slot as shown.

4. Then press the release the memory dummy card from the 5-in-1 card reader slot as shown.

5. Remove the ten screws fastening the upper case and the lower case assembly on the bottom.

6. Remove the eight screws fastening the upper case assembly and the lower case assembly on the front

side.

Chapter 3

7. Disconnect the touchpad FFC, left speaker cable, button board FFC, and LED board FFC from the main

board.

8. Carefully detach the upper case assembly from the lower case assembly.

Disassembling the Lower Case Assembly

1. Disconnect the USB cable from the main board.

2. Remove the screw fastening the USB board and take out the board and its cable from the lower case.

3. Then detach the USB cable from the USB board.

4. Disconnect the Bluetooth cable from the main board.

5. Take out the Bluetooth module and its cable from the lower case as shown.

6. Then detach the Bluetooth cable from the Bluetooth module.

7. Disconnect the right speaker cable from the main board.

8. Remove the two screws fastening the right speaker, then lift it out from the lower case.

Chapter 3

9. Pull the RF cable through the opening in the lower case as shown.

10. Remove the screw holding the RF board to the lower case.

11. Take out the RF board from the lower case, then detach the RF cable from the RF board as shown.

12. Remove the RJ-11 jack from the lower case.

NOTE: RF board on selected models only.

13. Remove the screw fastening the main board to the lower case.

14. Detach the main board from the lower case as shown.

15. Turn the main board over, then remove the DC-in connector from the board as shown.

Chapter 3

Disassembling the Upper Case Assembly

1. Turn the upper case over.

2. Remove the two screws fastening the button board.

3. Detach the button board with FFC from the upper case as shown.

4. Remove the two screws fastening the LED board.

5. Detach the LED board with FFC from the upper case as shown.

6. Remove the two screws fastening the left speaker.

7. Remove the left speaker from the upper case as shown.

Chapter 3

Disassembling the LCD Module

1. Remove the four screw rubbers as shown.

2. Then remove the four screws fastening the LCD bezel.

3. Detach the LCD bezel from the LCD module carefully.

4. Remove the four screws holding the LCD to the LCD panel.

5. Detach the CCD cable connector from the CCD board.

6. Take out the CCD module from the LCD panel.

7. Remove the screw fastening the CCD board to the CCD bracket.

8. Lift out the LCD from the LCD panel as shown.

9. Detach the two inverter cable connectors from the inverter board.

10. Remove the four screws fastening the left LCD bracket and detach it.

11. Remove the four screws fastening the right LCD bracket and detach it.

12. Disconnect the LCD cable from the rear side of the LCD.

Chapter 3

Disassembling the External Modules

Disassembling the HDD Module

1. Remove the four screws holding the HDD (hard disk drive) case; two on each side.

2. Carefully slide out the hard disk drive from the HDD case.

Disassembling the ODD Module

1. Remove the three screws holding the optical bracket.

2. Then remove the optical bracket from the optical disk drive.

Chapter 3

Chapter 4

Troubleshooting

Use the following procedure as a guide for computer problems.

NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or

modified options can give false errors and invalid system responses.

1. Obtain the failing symptoms in as much detail as possible.

2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating

the same operation.

3. Use the following table with the verified symptom to determine which page to go to.

Symptoms (Verified)

Go To

Power failure (The power indicator does not go

on or stay on).

“Power System Check” on page 73

POST does not complete. No beep or error

codes are indicated.

“Power-On Self-T e st (POST) Error Message” on

page 76

“Undetermined Problems” on page 88

POST detects an error and displayed messages “Error Message List” on page 77

on screen.

Other symptoms (i.e. LCD display problems or

others).

“Power-On Self-T e st (POST) Error Message” on

page 76

Symptoms cannot be re-created (intermittent

problems).

Use the customer-reported symptoms and go to

“Power-On Self-T e st (POST) Error Message” on

page 76

“Intermittent Problems” on page 87

“Undetermined Problems” on page 88

Chapter 4

System Check Procedures

External Diskette Drive Check

Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is

required.

NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause

damage to the drive or cause the drive to fail.

Do the following to select the test device:

1. Boot from the diagnostics diskette and start the diagnostics program.

2. See if FDD Test is passed as the program runs to FDD Test.

3. Follow the instructions in the message window.

If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.

If the error still remains:

1. Reconnect the external diskette drive/DVD-ROM module.

2. Replace the external diskette drive/CD-ROM module.

3. Replace the main board.

External CD-ROM Drive Check

Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does

not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.

Do the following to select the test device:

1. Boot from the diagnostics diskette and start the diagnostics program.

2. See if CD-ROM Test is passed when the program runs to CD-ROM Test.

3. Follow the instructions in the message window.

If an error occurs, reconnect the connector on the System board. If the error still remains:

1. Reconnect the external diskette drive/CD-ROM module.

2. Replace the external diskette drive/CD-ROM module.

3. Replace the main board.

Keyboard or Auxiliary Input Device Check

Remove the external keyboard if the internal keyboard is to be tested.

If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable

extending from the keyboard is correctly seated in the connector on the system board.

If the keyboard cable connection is correct, run the Keyboard Test.

If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a

non-defective FRU:

1. Reconnect the keyboard cables.

2. Replace the keyboard.

3. Replace the main board.

The following auxiliary input devices are supported by this computer:

Numeric keypad

External keyboard

Chapter 4

If any of these devices do not work, reconnect the cable connector and repeat the failing operation.

Memory check

Memory errors might stop system operations, show error messages on the screen, or hang the system.

1. Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board).

2. Go to the diagnostic memory in the test items.

3. Press F2 in the test items.

4. Follow the instructions in the message window.

NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.

Power System Check

To verify the symptom of the problem, power on the computer using each of the following power sources:

1. Remove the battery pack.

2. Connect the power adapter and check that power is supplied.

3. Disconnect the power adapter and install the charged battery pack; then check that power is supplied by

the battery pack.

If you suspect a power problem, see the appropriate power supply check in the following list:

“Check the Power Adapter” on page 74

“Check the Battery Pack” on page 75

Chapter 4

Check the Power Adapter

Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power

adapter cable. See the following figure:

Pin 1: +19 to +20.5V

Pin 2: 0V, Ground

1. If the voltage is not correct, replace the power adapter.

2. If the voltage is within the range, do the following:

Replace the System board.

If the problem is not corrected, see “Undetermined Problems” on page 88.

If the voltage is not correct, go to the next step.

NOTE: An audible noise from the power adapter does not always indicate a defect.

3. If the power-on indicator does not light up, check the power cord of the power adapter for correct

continuity and installation.

4. If the operational charge does not work, see “Check the Battery Pack” on page 75.

Chapter 4

Check the Battery Pack

To check the battery pack, do the following:

From Software:

1. Check out the Power Management in Control Panel

2. In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total

Battery Power Remaining are correct.

3. Repeat the steps 1 and 2, for both battery and adapter.

4. This helps you identify first the problem is on recharging or discharging.

From Hardware:

1. Power off the computer.

2. Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the

following figure

3. If the voltage is still less than 7.5 Vdc after recharging, replace the battery.

To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%

of the total power remaining when installed in the computer.

If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.

Re-install the battery pack.

If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light

up, replace the DC/DC charger board.

Touchpad Check

If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a

non-defective FRU:

1. Reconnect the touchpad cables.

2. Replace the touchpad.

3. Replace the system board.

After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement

can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware

problem. No service actions are necessary if the pointer movement stops in a short period of time.

Chapter 4

Power-On Self-Test (POST) Error Message

The POST error message index lists the error message and their possible causes. The most likely cause is

listed first.

NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU

replacement does not solve the problem, put the original part back in the computer. Do not replace a

non-defective FRU.

This index can also help you determine the next possible FRU to be replaced when servicing a computer.

If the symptom is not listed, see “Undetermined Problems” on page 88.

The following lists the error messages that the BIOS displays on the screen and the error symptoms classified

by function.

NOTE: Most of the error messages occur during POST. Some of them display information about a hardware

device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the

way it has been configured.

NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter

Setup and install Setup defaults or correct the error.

Chapter 4

Index of Error Messages

Error Code List

Error Codes

Error Messages

Equipment Configuration Error

006

Causes:

1. CPU BIOS Update Code Mismatch

2. IDE Primary Channel Master Drive Error

(THe causes will be shown before “Equipment Configuration

Error”)

010

070

071

072

110

Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh)

Real Time Clock Error

CMOS Battery Bad

CMOS Checksum Error

System disabled.

Incorrect password is specified.

Battery critical LOW

In this situation BIOS will issue 4 short beeps then shut down

system, no message will show.

Thermal critical High

In this situation BIOS will shut down system, not show message.

Error Message List

Error Messages

FRU/Action in Sequence

Failure Fixed Disk

Reconnect hard disk drive connector.

“Load Default Settings” in BIOS Setup Utility.

Hard disk drive

System board

Stuck Key

see “Keyboard or Auxiliary Input Device Check” on page 72.

Unlock external keyboard

Keyboard error

Keyboard Controller Failed

Keyboard locked - Unlock key switch

Monitor type does not match CMOS - Run Setup Run “Load Default Settings” in BIOS Setup Utility.

Shadow RAM Failed at offset: nnnn

System RAM Failed at offset: nnnn

Extended RAM Failed at offset: nnnn

BIOS ROM

System board

DIMM

System board

DIMM

System board

System battery is dead - Replace and run Setup Replace RTC battery and Run BIOS Setup Utility to reconfigure

system time, then reboot system.

System CMOS checksum bad - Default

configuration used

RTC battery

Run BIOS Setup Utility to reconfigure system time, then reboot

system.

System timer error

RTC battery

Run BIOS Setup Utility to reconfigure system time, then reboot

system.

System board

Chapter 4

Error Message List

Error Messages

Real time clock error

FRU/Action in Sequence

RTC battery

Run BIOS Setup Utility to reconfigure system time, then reboot

system.

System board

Previous boot incomplete - Default configuration Run “Load Default Settings” in BIOS Setup Utility.

used

RTC battery

System board

Memory size found by POST differed from

CMOS

Run “Load Default Settings” in BIOS Setup Utility.

DIMM

System board

Diskette drive A error

Check the drive is defined with the proper diskette type in BIOS

Setup Utility

See “External Diskette Drive Check” on page 72.

Incorrect Drive A type - run SETUP

Check the drive is defined with the proper diskette type in BIOS

Setup Utility

System cache error - Cache disabled

CPU ID:

System board

DMA Test Failed

DIMM

System board

Software NMI Failed

DIMM

System board

Fail-Safe Timer NMI Failed

Device Address Conflict

DIMM

System board

Run “Load Default Settings” in BIOS Setup Utility.

RTC battery

System board

Allocation Error for device

Failing Bits: nnnn

Run “Load Default Settings” in BIOS Setup Utility.

RTC battery

System board

DIMM

BIOS ROM

System board

Fixed Disk n

None

Invalid System Configuration Data

BIOS ROM

System board

I/O device IRQ conflict

Run “Load Default Settings” in BIOS Setup Utility.

RTC battery

System board

Operating system not found

Enter Setup and see if fixed disk and drive A: are properly identified.

Diskette drive

Hard disk drive

System board

Chapter 4

Error Message List

No beep Error Messages

FRU/Action in Sequence

No beep, power-on indicator turns off and LCD is Power source (battery pack and power adapter). See “Power

blank.

System Check” on page 73..

Ensure every connector is connected tightly and correctly.

Reconnect the DIMM.

LED board.

System board.

No beep, power-on indicator turns on and LCD is Power source (battery pack and power adapter). See “Power

blank.

System Check” on page 73..

Reconnect the LCD connector

Hard disk drive

LCD inverter ID

LCD cable

LCD Inverter

LCD

System board

No beep, power-on indicator turns on and LCD is Reconnect the LCD connectors.

blank. But you can see POST on an external

CRT.

LCD inverter ID

LCD cable

LCD inverter

LCD

System board

No beep, power-on indicator turns on and a

blinking cursor shown on LCD during POST.

Ensure every connector is connected tightly and correctly.

System board

No beep during POST but system runs correctly. Speaker

System board

Chapter 4

Phoenix BIOS Beep Codes

Code

Beeps

POST Routine Description

Verify Real Mode

02h

03h

04h

06h

08h

09h

0Ah

0Bh

0Ch

0Eh

0Fh

10h

11h

Disable Non-Maskable Interrupt (NMI)

Get CPU type

Initialize system hardware

Initialize chipset with initial POST values

Set IN POST flag

Initialize CPU registers

Enable CPU cache

Initialize caches to initial POST values

Initialize I/O component

Initialize the local bus IDE

Initialize Power Management

Load alternate registers with initial POST

values

12h

13h

14h

16h

17h

18h

1Ah

1Ch

20h

22h

24h

26h

28h

29h

2Ah

2Ch

2Eh

Restore CPU control word during warm boot

Initialize PCI Bus Mastering devices

Initialize keyboard controller

BIOS ROM checksum

1-2-2-3

Initialize cache before memory autosize

8254 timer initialization

8237 DMA controller initialization

Reset Programmable Interrupt Controller

Test DRAM refresh

1-3-1-1

1-3-1-3

Test 8742 Keyboard Controller

Set ES segment register to 4 GB

Enable A20 line

Autosize DRAM

Initialize POST Memory Manager

Clear 215 KB base RAM

1-3-4-1

1-3-4-3

RAM failure on address line xxxx

RAM failure on data bits xxxx of low byte of

memory bus

2Fh

30h

Enable cache before system BIOS shadow

1-4-1-1

RAM failure on data bits xxxx of high byte of

memory bus

32h

33h

36h

38h

3Ah

3Ch

3Dh

42h

45h

Test CPU bus-clock frequency

Initialize Phoenix Dispatch Manager

Warm start shut down

Shadow system BIOS ROM

Autosize cache

Advanced configuration of chipset registers

Load alternate registers with CMOS values

Initialize interrupt vectors

POST device initialization

Chapter 4

Code

Beeps

POST Routine Description

Check ROM copyright notice

46h

48h

49h

4Ah

4Bh

4Ch

4Eh

50h

51h

52h

54h

58h

59h

5Ah

5Bh

5Ch

60h

62h

64h

66h

67h

68h

69h

6Ah

6Bh

6Ch

6Eh

2-1-2-3

Check video configuration against CMOS

Initialize PCI bus and devices

Initialize all video adapters in system

QuietBoot start (optional)

Shadow video BIOS ROM

Display BIOS copyright notice

Display CPU type and speed

Initialize EISA board

Test keyboard

Set key click if enabled

2-2-3-1

Test for unexpected interrupts

Initialize POST display service

Display prompt “Press F2 to enter SETUP”

Disable CPU cache

Test RAM between 512 and 640 KB

Test extended memory

Test extended memory address lines

Jump to User Patch1

Configure advanced cache registers

Initialize Multi Processor APIC

Enable external and CPU caches

Setup System Management Mode (SMM) area

Display external L2 cache size

Load custom defaults (optional)

Display shadow-area message

Display possible high address for UMB

recovery

70h

72h

76h

7Ch

7Eh

80h

81h

82h

83h

84h

85h

86h

87h

Display error messages

Check for configuration errors

Check for keyboard errors

Set up hardware interrupt vectors

Initialize coprocessor if present

Disable onboard Super I/O ports and IRQs

Late POST device initialization

Detect and install external RS232 ports

Configure non-MCD IDE controllers

Detect and install external parallel ports

Initialize PC-compatible PnP ISA devices

Re-initialize onboard I/O ports

Configure Motherboard Configurable Devices

(optional)

88h

89h

8Ah

8Bh

Initialize BIOS Area

Enable Non-Maskable Interrupts (NMIs)

Initialize Extended BIOS Data Area

Test and initialize PS/2 mouse

Chapter 4

Code

Beeps

POST Routine Description

Initialize floppy controller

8Ch

8Fh

90h

91h

92h

93h

95h

96h

97h

98h

Determine number of ATA drives (optional)

Initialize hard-disk controllers

Initialize local-bus hard-disk controllers

Jump to UserPatch2

Build MPTABLE for multi-processor boards

Install CD ROM for boot

Clear huge ES segment register

Fixup Multi Processor table

1-2

Search for option ROMs. One long, two short

beeps on checksum failure.

99h

9Ah

9Ch

9Dh

9Eh

9Fh

A0h

A2h

A4h

A8h

AAh

ACh

AEh

B0h

B2h

B4h

B5h

B6h

B9h

BAh

BBh

BCh

BDh

BEh

BFh

C0h

C1h

C2h

C3h

C4h

C5h

C6h

C7h

C8h

C9h

Check for SMART drive (optional)

Shadow option ROMs

Set up Power Management

Initialize security engine (optional)

Enable hardware interrupts

Determine number of ATA and SCSI drives

Set time of day

Check key lock

Initialize Typematic rate

Erase F2 prompt

Scan for F2 key stroke

Enter SETUP

Clear Boot flag

Check for errors

POST done- prepare to boot operating system

One short beep before boot

Terminate QuietBoot (optional)

Check password (optional)

Prepare Boot

Initialize DMI parameters

Initialize PnP Option ROMs

Clear parity checkers

Display MultiBoot menu

Clear screen (optional)

Check virus and backup reminders

Try to boot with INT 19

Initialize POST Error Manager (PEM)

Initialize error logging

Initialize error display function

Initialize system error handler

PnPnd dual CMOS (optional)

Initialize notebook docking (optional)

Initialize notebook docking late

Force check (optional)

Extended checksum (optional)

Chapter 4

Code

Beeps

POST Routine Description

Unknown interrupt

D2h

E0h

E1h

E2h

E3h

E4h

E5h

E6h

E7h

E8h

E9h

EAh

EBh

ECh

EDh

EEh

EFh

F0h

F1h

F2h

F3h

F4h

F5h

F6h

F7h

Initialize the chipset

Initialize the bridge

Initialize the CPU

Initialize the system timer

Initialize system I/O

Check force recovery boot

Checksum BIOS ROM

Go to BIOS

Set Huge Segment

Initialize Multi Processor

Initialize OEM special code

Initialize PIC and DMA

Initialize Memory type

Initialize Memory size

Shadow Boot Block

System memory test

Initialize interrupt vectors

Initialize Run Time Clock

Initialize video

Initialize System Management Mode

Output one beep before boot

Boot to Mini DOS

Clear Huge Segment

Boot to Full DOS

Chapter 4

Index of Symptom-to-FRU Error Message

LCD-Related Symptoms

Symptom / Error

LCD backlight doesn't work

Action in Sequence

Enter BIOS Utility to execute “Load Setup Default Settings”, then

reboot system.

LCD is too dark

Reconnect the LCD connectors.

LCD brightness cannot be adjusted

LCD contrast cannot be adjusted

Keyboard (if contrast and brightness function key doesn't work).

LCD inverter ID

LCD cable

LCD inverter

LCD

System board

Unreadable LCD screen

Missing pels in characters

Abnormal screen

Reconnect the LCD connector

LCD inverter ID

LCD cable

Wrong color displayed

LCD inverter

LCD

System board

LCD has extra horizontal or vertical lines

displayed.

LCD inverter ID

LCD inverter

LCD cable

LCD

System board

Indicator-Related Symptoms

Symptom / Error

Action in Sequence

Indicator incorrectly remains off or on, but system Reconnect the inverter board

runs correctly

Inverter board

System board

Power-Related Symptoms

Symptom / Error

Action in Sequence

Power shuts down during operation

Power source (battery pack and power adapter). See “Power

System Check” on page 73.

Battery pack

Power adapter

Hard drive & battery connection board

System board

The system doesn’t power-on.

The system doesn’t power-off.

Power source (battery pack and power adapter). See “Power

System Check” on page 73.

Battery pack

Power adapter

Hard drive & battery connection board

System board

Power source (battery pack and power adapter). See “Power

System Check” on page 73.

Hold and press the power switch for more than 4 seconds.

System board

Chapter 4

Power-Related Symptoms

Symptom / Error

Action in Sequence

Battery can’t be charged

See “Check the Battery Pack” on page 75.

Battery pack

System board

PCMCIA-Related Symptoms

Symptom / Error

Action in Sequence

System cannot detect the PC Card (PCMCIA)

PCMCIA slot assembly

System board

PCMCIA slot pin is damaged.

PCMCIA slot assembly

Memory-Related Symptoms

Symptom / Error

Action in Sequence

Memory count (size) appears different from

actual size.

Enter BIOS Setup Utility to execute “Load Default Settings, then

reboot system.

DIMM

System board

Speaker-Related Symptoms

Symptom / Error

Action in Sequence

In Windows, multimedia programs, no sound

comes from the computer.

Audio driver

Speaker

System board

Internal speakers make noise or emit no sound. Speaker

System board

Power Management-Related Symptoms

Symptom / Error

Action in Sequence

See “Save to Disk (S4)” on page 45.

The system will not enter hibernation

Keyboard (if control is from the keyboard)

Hard disk drive

System board

The system doesn't enter hibernation mode and

four short beeps every minute.

Press Fn+oand see if the computer enters hibernation mode.

Touchpad

Keyboard

Hard disk connection board

Hard disk drive

System board

The system doesn’t enter standby mode after

closing the LCD

See “Save to Disk (S4)” on page 45.

LCD cover switch

System board

The system doesn't resume from hibernation

mode.

See “Save to Disk (S4)” on page 45.

Hard disk connection board

Hard disk drive

System board

The system doesn't resume from standby mode See “Save to Disk (S4)” on page 45.

after opening the LCD.

LCD cover switch

System board

Chapter 4

Power Management-Related Symptoms

Symptom / Error

Action in Sequence

Battery fuel gauge in Windows doesn’t go higher Remove battery pack and let it cool for 2 hours.

than 90%.

Refresh battery (continue use battery until power off, then charge

battery).

Battery pack

System board

System hangs intermittently.

Reconnect hard disk/CD-ROM drives.

Hard disk connection board

System board

Peripheral-Related Symptoms

Symptom / Error

Action in Sequence

System configuration does not match the

installed devices.

Enter BIOS Setup Utility to execute “Load Default Settings”, then

reboot system.

Reconnect hard disk/CD-ROM/diskette drives.

External display does not work correctly.

Press Fn+F5, LCD/CRT/Both display switching

System board

USB does not work correctly

Print problems.

System board

Ensure the “Parallel Port” in the “Onboard Devices Configuration” of

BIOS Setup Utility is set to Enabled.

Onboard Devices Configuration

Run printer self-test.

Printer driver

Printer cable

Printer

System Board

Serial or parallel port device problems.

Ensure the “Serial Port” in the Devices Configuration” of BIOS Setup

Utility is set to Enabled.

Device driver

Device cable

Device

System board

Keyboard/Touchpad-Related Symptoms

Symptom / Error

Action in Sequence

Keyboard (one or more keys) does not work.

Reconnect the keyboard cable.

Keyboard

System board

Touchpad does not work.

Reconnect touchpad cable.

Touchpad board

System board

Modem-Related Symptoms

Symptom / Error

Action in Sequence

Internal modem does not work correctly.

Modem phone port

modem combo board

System board

NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined

Problems” on page 88.

Chapter 4

Intermittent Problems

Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a

hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement

should be considered only when a recurring problem exists.

When analyzing an intermittent problem, do the following:

1. Run the advanced diagnostic test for the system board in loop mode at least 10 times.

2. If no error is detected, do not replace any FRU.

3. If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.

Chapter 4

Undetermined Problems

The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,

whether a short circuit is suspected, or whether the system is inoperative.

Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).

NOTE: Verify that all attached devices are supported by the computer.

NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power

System Check” on page 73.):

1. Power-off the computer.

2. Visually check them for damage. If any problems are found, replace the FRU.

3. Remove or disconnect all of the following devices:

Non-Acer devices

Printer, mouse, and other external devices

Battery pack

Hard disk drive

DIMM

CD-ROM/Diskette drive Module

PC Cards

4. Power-on the computer.

5. Determine if the problem has changed.

6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.

7. If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:

System board

LCD assembly

Chapter 4

Chapter 5

Jumper and Connector Locations

Top View

2 3 4

1100

1122

1155

1166

1133 1144

JP1

LCD Connector

JP36

Mainboard to LED Board

Connector

JP3

JP34

JP4

Speaker (Left) Connector

Speaker (Right) Connector

Internal MIC Connector

South Bridge (ICH8M)

U12

JP9

PCI Express Card Socket

Power/Suspend LED

LED1

LED2

JP13

Battery Charge/Discharge LED

JP6

Internal Track-Pad Connector

Mainboard to Audio Board

Connector

JP5

JP2

Internal Keyboard Connector

JP11

JP12

Mainboard to USB Board

Connector

Mainboard to Button Board

Connector

Bluetooth Module Connector

Chapter 5

Bottom View

22 23 25

PJP1

PJP2

JP14

JP15

JP25

JP20

JP19

JP17

JP22

JP16

JP19

JP18

JP23

DC-in Power Jack

Battery Connector

CRT Connector

DVI-D Connector

ODD Connector

JP24

TV-out Connector

JP26

JP27

U23

IEEE1394 Connector

SATA HDD Connector

North Bridge (965PM/965GM)

U28

Mini Card (WLAN) Socket

Mini Card (TV-Tuner) Socket

MDC Connector

U29

Volume Control

JP28

JP29

JP31

JP32

U33

DDRII Memory Socket

Headphone/SPDIF Jack

Mic-in Jack

CPU Socket

Internal Fan Connector

VGA Board Connector

RJ45 (LAN) Connector

USB (Dual) Connectors

Audio Codec Controller

Line-in Jack

JP33

Chapter 5

Chapter 6

FRU (Field Replaceable Unit) List

This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Aspire eME510. Refer to this

chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).

Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your

regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service

Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from

those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer

office to order FRU parts for repair and service of customer machines.

NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to

dispose it properly, or follow the rules set by your regional Acer office on how to return it.

Chapter 6

161

Aspire eME510 Exploded Diagram

Aspire eME510 FRU List

Category

Description

Part Number

Adapter

ADAPTER

Battery

ADAPTER 65W 3PIN DELTA SADP-65KB DBFF

ADAPTER 65W 3PIN DELTA SADP-65KB DFA

ADAPTER 65W 3PIN LITEON PA-1650-02 LR

ADAPTER 65W 3PIN LITEON PA-1650-02AC

ADAPTER 65W 3PIN HIPRO AC-OK065B13

AP.06501.009

AP.06501.013

AP.06503.012

AP.06503.016

AP.0650A.010

BATTERY

BATTERY LI-ION 6CELLS 4KMAH PANASONIC PA 3S2P 4.0AH 7

01K 0FA

BT.00605.015

BATTERY

BATTERY LI-ION 6CELLS 4KMAH SANYO SA 3S2P 4AH 7 01K 0FA

BT.00603.033

BT.00607.010

BATTERY LI-ION 6CELLS 4KMAH SIMPLO SP PA 3S2P 4.0AH 7

01K 0FA

BATTERY

Board

BATTERY LI-ION 6CELLS 4KMAH SONY SY 3S2P 4.0AH 7 01K 0FA

BATTERY LI-ION 6CELLS 4.4KMAH SANYO SA 3S2P

BATTERY LI-ION 6CELLS 4.4KMAH SONY SA 3S2P

BT.00604.018

BT.00603.042

BT.00604.025

BT.00605.021

BATTERY LI-ION 6CELLS 4.4KMAH PANASONIC SA 3S2P

BOARD

MODEM BOARD

FX.22500.022

BOARD

BLUETOOTH BOARD

54.AR102.001

MINI WLAN/B FOXCONN 802.11BG T77H030.00 (BRCM4312)

NI.23600.029

NI.23600.007

MINI WLAN/B FOXCONN 802.11 ATHEROS XB63 BG T60H976.00

FW:V06

BOARD

BUTTON BOARD W/O LED 15.4”

TBD

162

Chapter 6

Category

BOARD

Description

LED BOARD W/O BUTTON 15.4”

Part Number

TBD

BOARD

USB BOARD FOR TV

55.ALB02.003

BOARD

USB BOARD FOR W/O TV

RF BOARD FOR DTV

55.AHE02.004

55.AHE02.005

BOARD

VGA BOARD-M71M 128MB

VG.71M02.002

BOARD

VGA BOARD-M71M 256MB W/HDCP

USB BOARD W/O CIR 15.4

INVERTER BOARD 15.4

VG.71M02.001

55.ALB02.003

19.AHE02.001

Cable

CABLE

RJ11 CABLE 15.4

50.AHE02.001

CABLE

FFC CABLE - T/P TO MB

BLUE TOOTH CABLE 15.4”

27.TAVV5.008

50.AHE02.003

CABLE

USB CABLE 15.4”

RF CABLE 15.4

50.AHE02.004

50.AHE02.005

CABLE

7 PIN MINI-DIN S-VIDEO TO 4 CABLE

PAL TO NTSC CONNECTOR

50.ABD02.001

20.ABD02.001

CABLE

SMB JACK

DVB-T ANT

50.ABD02.002

50.ABD02.003

Chapter 6

163

Category

Description

Part Number

CABLE

DC-IN CABLE (65W) UMA

50.AHE02.009

CABLE

POWER CORD US 3 PIN

POWER CORD EU 3 PIN

POWER CORD AUS 3 PIN

POWER CORD UK 3 PIN

27.TAVV5.001

27.TAVV5.002

27.TAVV5.003

27.TAVV5.004

27.TAVV5.005

27.TAVV5.006

27.TAVV5.007

27.TAVV5.009

27.TAVV5.010

27.TAVV5.011

27.TAVV5.012

27.TAVV5.013

27.TAVV5.014

50.AHE02.002

50.AHE02.006

50.AHE02.007

50.AHE02.008

50.AH902.001

POWER CORD CHINA 3 PIN

POWER CORD SWISS 3 PIN

POWER CORD ITALIAN 3 PIN

POWER CORD JP 3 PIN

POWER CORD SOUTH AFRICA 3 PIN

POWER CORD KOERA 3 PIN

POWER CORD ISRAEL 3 PIN

POWER CORD INDIA 3 PIN

POWER CORD TWN 3 PIN

FFC CABLE - T/P TO MB

LCD WIRESET 15.4

ANTENNA R 15.4

ANTENNA L-15.4

LCD WIRESET 15.4 FOR W/O CCD FUNCTION

Assembly Parts

CASE/COVER/

MIDDLE COVER 15.4”

42.N0202.001

BRACKET ASSEMBLY

CASE/COVER/

UPPER CASE ASSY 15.4 W/TP TP BRACKET TP FFC - UMA

60.N0202.001

BRACKET ASSEMBLY

CASE/COVER/

BRACKET

LOWER CASE ASSY UMA W/O TV-15.4

60.N0202.002

ASSEMBL

164

Chapter 6

Category

Description

THERMAL DOOR 15.4” UMA

Part Number

CASE/COVER/

BRACKET

42.AHE02.002

ASSEMBL

CASE/COVER/

BRACKET ASSEMBLY

ODD BEZEL-COMBO

42.AHE02.006

42.AHE02.004

ODD BEZEL-SUPER MULTI

CASE/COVER/

BRACKET ASSEMBLY

ODD BRACKET 15.4"

HDD DOOR 15.4

33.AHE02.001

42.AHE02.007

CASE/COVER/

BRACKET ASSEMBLY

CASE/COVER/

HDD BRACKET 15.4

33.AHE02.002

BRACKET ASSEMBLY

CASE/COVER/

BRACKETASSEMBLY

LCD COVER ASSY 15.4 IN. LOGO W/MIC W/ANTENNA

LCD BEZEL ASSY 15.4 FOR CCD

60.N0202.003

60.N0202.004

33.AHE02.003

33.AHE02.004

60.N0202.003

60.N0302.001

33.AHE02.003

CASE/COVER/

BRACKETASSEMBLY

CASE/COVER/

BRACKET ASSEMBLY

LCD BRACKET SET R&L 15.4

CASE/COVER/

BRACKETASSEMBLY

CCD BRACKET-15.4

CASE/COVER/

BRACKETASSEMBLY

LCD COVER ASSY 15.4 IN. LOGO W/MIC W/ANTENNA

LCD BEZEL ASSY 15.4 FOR W/O CCD FUNCTION

LCD BRACKET SET R&L 15.4

CASE/COVER/

BRACKETASSEMBLY

CASE/COVER/

BRACKETASSEMBLY

CPU

CPU/PROCESSOR

INTEL CPU MEROM SINGLE CORE CM540 1.86G

LF80537NE0361M SLA2F A1 UFCPGA 478P

KC.N0001.540

KC.N0001.550

INTEL CPU MEROM SINGLE CORE CM550 2G IC

LF80537NE0411M SLA2E A1

Chapter 6

165

Category

Description

Part Number

CPU/PROCESSOR

INTEL CPU MEROM SINGLE CORE CM530SR 1.73G IC

LF80537NE0301M SLA2G A1

KC.NSR01.530

CPU/PROCESSOR

Combo Drive

INTEL CPU MEROM SINGLE CORE CM560 2.13G

LF80537NE0461M SLA2D A1

KC.N0001.560

KC.N0001.570

KC.14001.CMT

INTEL CPU MEROM SINGLE CORE CM570 2.26G

LF80537NE0511M SLA2C A1

INTEL CPU CELERON DUAL CORE CMT1400 1.73G

LF80537NE030512 SLAQL M0

COMBO DRIVE

DVD RW DRIVE

DVD/CDRW 24X COMBO MODULE

6M.AHE02.001

KO.0240D.005

KO.0240E.005

KO.02401.005

DVD/CDRW COMBP DRIVE HLDS GCC-T10N VISTA 0FA

DVD/CDRW COMBP DRIVE SONY CRX880A VISTA 0FA

DVD/CDRW COMBP DRIVE TSST TS-L462D AC02 0FA

DVD RW DRIVE

Hard Disk

DVD SUPER MULTI MODULE TRAY IN

6M.AHE02.002

KU.00805.038

KU.00805.043

KU.00807.055

KU.00807.058

KU.00809.010

KU.0080D.027

TBD

DVD SUPER MULTI DRIVE PIONEER DVR-K17RS 0FA

DVD SUPER MULTI DRIVE PIONEER DVR-KD08RS 0FA

DVD SUPER MULTI DRIVE PANASONIC UJ-850UAA1-A VISTA

DVD SUPER MULTI DRIVE PANASONIC UJ-870BAA-A 0FA

DVD SUPER MULTI DRIVE PHILIPS DS-8A1P 0FA

DVD SUPER MULTI DRIVE HLDS GSA-T20N 0FA

DVD SUPER MULTI DRIVE HLDS GSA-T40N 0FA

DVD SUPER MULTI DRIVE SONY AD-7530A 0FA

DVD SUPER MULTI DRIVE SONY AD-7560A 0FA

DVD SUPER MULTI DRIVE SONY AD-7530B 0FA

KU.0080E.002

KU.0080E.005

KU.0080E.008

HDD/HARD DISK

DRIVE

HDD SATA 80G 5400RPM HGST HTS541680J9SA00 SURUGA-B LF

F/W: C70P

KH.08007.021

KH.08007.025

KH.08001.030

KH.08004.010

KH.08004.011

HDD/HARD DISK

DRIVE

HDD SATA 80G 5400RPM HGST HTS542580K9SA00 0FA

HDD/HARD DISK

DRIVE

HDD SATA 80G 5400RPM SEAGATE ST980811AS SATA 8MB LF

3.ALD

HDD/HARD DISK

DRIVE

HDD SATA 80G 5400RPM TOSHIBA MK8037GSX Gemini BS SATA

LF F/W:DL250J

HDD/HARD DISK

DRIVE

HDD SATA 80G 5400RPM TOSHIBA MK8046GSX 0FA

166

Chapter 6

Category

Description

Part Number

HDD/HARD DISK

DRIVE

HDD SATA 80G 5400RPM WD WD800BEVS-22RST0 ML80 SATA LF

F/W:04.01G04

KH.08008.033

HDD/HARD DISK

DRIVE

HDD SATA 120G 5400RPM HGST HTS541612J9SA00 SURUGA-B LF

F/W: C70P

KH.12007.010

HDD/HARD DISK

DRIVE

HDD SATA 120G 5400RPM HGST HTS542512K9SA00 0FA

KH.12007.014

KH.12001.031

KH.12001.032

KH.12004.006

HDD/HARD DISK

DRIVE

HDD SATA 120G 5400RPM SEAGATE ST9120822AS SATA 8MB LF

3.ALD

HDD/HARD DISK

DRIVE

HDD SATA 120G 5400RPM SEAGATE ST9120817AS 0FA

HDD/HARD DISK

DRIVE

HDD SATA 120G 5400RPM TOSHIBA MK1237GSX Gemini BS

SATA LF

F/W:DL150J

HDD/HARD DISK

DRIVE

HDD SATA 120G 5400RPM TOSHIBA MK1246GSX 0FA

KH.12004.007

KH.12008.018

HDD/HARD DISK

DRIVE

HDD SATA 120G 5400RPM WD WD1200BEVS-22RST0 ML80 SATA

F/W:04.01G04

HDD/HARD DISK

DRIVE

HDD SATA 120G 5400RPM WD WD1200BEVS-22UST0 0FA

KH.12008.019

KH.16007.011

HDD/HARD DISK

DRIVE

HDD SATA 160G 5400RPM HGST HTS541616J9SA00 SURUGA-B LF

F/W: C70P

HDD/HARD DISK

DRIVE

HDD SATA 160G 5400RPM HGST HTS542516K9SA00 0FA

KH.16007.016

KH.16001.026

KH.16001.029

KH.16004.001

HDD/HARD DISK

DRIVE

HDD SATA 160G 5400RPM SEAGATE ST9160821AS SATA 8MB LF

3.ALD

HDD/HARD DISK

DRIVE

HDD SATA 160G 5400RPM SEAGATE ST9160827AS 0FA

HDD/HARD DISK

DRIVE

HDD SATA 160G 5400RPM TOSHIBA MK1637GSX Gemini BS

SATA LF

F/W: DL050J

HDD/HARD DISK

DRIVE

HDD SATA 160G 5400RPM TOSHIBA MK1646GSX 0FA

KH.16004.002

KH.16008.019

HDD/HARD DISK

DRIVE

HDD SATA 160G 5400RPM WD WD1600BEVS-22RST0 ML80 SATA

F/W:04.01G04

HDD/HARD DISK

DRIVE

HDD SATA 160G 5400RPM WD WD1600BEVT-22ZCT0 0FA

KH.16008.022

KH.25008.018

HDD/HARD DISK

DRIVE

HDD SATA 250G 5400RPM WD WD2500BEVS-22UST0;

FW: 01.01A01; HW: T0

HDD/HARD DISK

DRIVE

HDD SATA 250G 5400RPM HGST HDD 250G .37"H

HTS542525K9SA00 0FA

KH.25007.011

KH.25004.001

KH.25001.011

KH.32008.013

KH.20004.001

HDD/HARD DISK

DRIVE

HDD SATA 250G 5400RPM TOSHIBA MK2546GSX 0FA

HDD SATA 250G 5400RPM SEAGATE ST9250827AS 0FA

HDD SATA 320G 5400RPM WD WD3200BEVT-22ZCT0 0FA

HDD SATA 200G 4200RPM TOSHIBA MK2035GSS

HDD/HARD DISK

DRIVE

HDD/HARD DISK

DRIVE

HDD/HARD DISK

DRIVE

Chapter 6

167

Category

Keyboard

Description

Part Number

KEYBOARD

LCD Panel

KEYBOARD INTE(UI) BLACK AS

KB.INT00.442

KB.INT00.474

KB.INT00.473

KB.INT00.472

KB.INT00.471

KB.INT00.470

KB.INT00.469

KB.INT00.468

KB.INT00.467

KB.INT00.465

KB.INT00.464

KB.INT00.463

KB.INT00.462

KB.INT00.459

KB.INT00.457

KB.INT00.455

KB.INT00.453

KB.INT00.452

KB.INT00.451

KB.INT00.449

KB.INT00.448

KB.INT00.447

KB.INT00.446

KB.INT00.445

KB.INT00.444

KB.INT00.443

KB.INT00.458

TBD

KEYBOARD ARE BLACK AS

KEYBOARD BE BLACK AS

KEYBOARD BZ BLACK AS

KEYBOARD CF BLACK AS

KEYBOARD CH BLACK AS

KEYBOARD CZ BLACK AS

KEYBOARD DM BLACK AS

KEYBOARD NL BLACK AS

KEYBOARD FR BLACK AS

KEYBOARD GR BLACK AS

KEYBOARD GK BLACK AS

KEYBOARD HG BLACK AS

KEYBOARD IT BLACK AS

KEYBOARD KO BLACK AS

KEYBOARD NW BLACK AS

KEYBOARD PO BLACK AS

KEYBOARD RU BLACK AS

KEYBOARD SA/CR BLACK AS

KEYBOARD SP BLACK AS

KEYBOARD SD/FN BLACK AS

KEYBOARD SW BLACK AS

KEYBOARD TI BLACK AS

KEYBOARD TR BLACK AS

KEYBOARD UK BLACK AS

KEYBOARD HB BLACK AS

KEYBOARD JP BLACK AS

KEYBOARD ND BLACK AS

KEYBOARD AR/FR BLACK AS

KEYBOARD CB BLACK AS

KB.INT00.475

KB.INT00.477

LCD

ASSY LCD MODULE 15.4 IN. WXGA GLARE W/ANTENNA CCD

6M.AHE02.003

168

Chapter 6

Category

Description

Part Number

LK.15408.025

LK.15408.029

LK.1540D.017

LK.15405.021

LK.15405.023

LK.15405.025

LK.15405.028

LK.15405.029

LK.15406.021

LK.15406.024

50.AHE02.006

LCD

LCD 15.4 WXGAG LPL LP154WX4-TLB2 (G) 8ms 220nits Nanking

LCD 15.4 WXGAG LPL LP154WX4-TLB4 0FA

LCD 15.4 WXGAG CMO N154I2-L05 Glare :220nits, 8ms 0.6mm/Asahi

LCD 15.4 WXGAG AUO B154EW02 V7(G) 8ms 220nits HW0A

LCD 15.4 WXGAG AUO B154EW02 V7-HW1A 154 WX G 0FA

LCD 15.4 WXGAG AUO B154EW08 V1

LCD 15.4 WXGAG AUO B154EW02 V7 2A 0FA

LCD 15.4 WXGAG AUO B154EW08 V1 3A 0FA

LCD 15.4 WXGAG SAMSUNG LTN154AT01-001(G) 220nits 8ms

LCD 15.4 WXGAG SAMSUNG LTN154AT01-A01 15.4" WX G 0FA

LCD WIRESET 15.4

LCD

ASSY LCD MODULE 15.4 IN. WXGA GLARE W/ANTENNA

6M.AJS02.001

60.AHE02.008

LCD

LCD BEZEL ASSY 15.4 FOR CCD

LCD

LCD BRACKET SET R&L 15.4

CCD MODULE 0.3M

33.AHE02.003

57.AHE02.001

LCD

CCD BRACKET-15.4

33.AHE02.004

47.AHE02.001

TBD

CCD MYLAR-15.4

ASSY LCD MODULE 15.4 IN. WXGA GLARE W/ANTENNA

LCD 15.4 WXGAG LPL LP154WX4-TLB2 (G) 8ms 220nits Nanking

LK.15408.025

LK.1540D.017

LCD 15.4 WXGAG CMO N154I2-L05

Glare: 220nits, 8ms 0.6mm/Asahi

LCD

LCD 15.4 WXGAG AUO B154EW02

V7(G) 8ms 220nits HW0A

LK.15405.021

LCD

LCD 15.4 WXGAG AUO B154EW02 V7-HW1A 154 WX G 0FA

LCD 15.4 WXGAG AUO B154EW08 V1

LCD 15.4 WXGAG SAMSUNG

LK.15405.023

LK.15405.025

LTN154AT01-001(G) 220nits 8ms

LK.15406.021

19.AHE02.001

50.AHE02.006

60.AHE02.007

60.AH902.003

INVERTER BOARD 15.4

LCD WIRESET 15.4

LCD COVER ASSY 15.4 IN. LOGO W/MIC W/ANTENNA

LCD BEZEL ASSY 15.4 FOR W/O CCD FUNCTION

Chapter 6

169

Category

Mainboard

Description

Part Number

MAINBOARD

MAINBOARD 65W GL960 UMA W/O CPU & MEMORY

TBD

MB.AHH02.001

MAINBOARB PM965 DISCRETE W/CARD READER_EXPRESS

CARD W/O CPU MEMORY

Memory

MEMORY

Fan

MEMORY 512MB DDRII 667 NANYA NT512T64UH8B0FN-3C

MEMORY 512MB DDRII 667 SAMSUNG M470T6554EZ3-CE6

MEMORY 512MB DDRII 667 SAMSUNG M470T6464QZ3-CE6

MEMORY 512MB DDRII 667 HYNIX HYMP164S64CP6-Y5

MEMORY 1GB DDRII 667 NANYA NT1GT64U8HB0BN-3C

MEMORY 1GB DDRII 667 SAMSUNG M470T2953EZ3-CE6

MEMORY 1GB DDRII 667 SAMSUNG M470T2864DZ3-CE6

MEMORY 1GB DDRII 667 HYNIX HYMP512S64CP8-Y5

MEMORY 1GB DDRII 667 A-D ELOPE1A0834Z

KN.51203.032

KN.5120B.023

KN.5120B.026

KN.5120G.024

KN.1GB03.014

KN.1GB0B.011

KN.1GB0B.014

KN.1GB0G.006

TBD

MEMORY 1GB DDRII 667 QIMODA HYS64T128021EDL-3S-B2

MEMORY 2GB DDRII 667 HYNIX

KN.1GB02.036

KN.2GB0G.004

KN.2GB04.001

KN.2GB0B.003

MEMORY 2GB DDRII 667 MICRON

MEMORY 2GB DDRII 667 SAMSUNG M470T5663QZ3-CE6

FAN

23.AHE02.001

60.AHE02.009

Heatsink

HEATSINK

CPU THERMAL MODULE

HEATSINK

VGA THERMAL (M71M)-DIS

60.AHE02.010

23.AHE02.002

Speaker

SPEAKER

SPEAKER R 15.4

170

Chapter 6

Category

SPEAKER

Description

Part Number

SPEAKER L 15.4

MIC SET 15.4

23.AHE02.003

SPEAKER

23.AHE02.004

Accessory

ACCESSORY

Miscellaneous

MISCELLANEOUS

Screw

REMOTE CONTROLLER EU

REMOTE CONTROLLER TS

REMOTE CONTROLLER SC

REMOTE CONTROLLER EN

LZ.20400.004

LZ.20400.005

LZ.20400.006

LZ.20400.007

CCD MYLAR-15.4

47.AHE02.001

47.AHE02.002

47.AHE02.003

47.AHE02.004

47.AHE02.002

47.AHE02.003

47.AHE02.004

47.AHE02.005

47.AHE02.006

47.AHE02.007

47.AHE02.008

TBD

LCD SCREW PAD 15.4

LCD SIDE RUBBER 15.4

LCD FRONT RUBBER 15.4

LCD SCREW PAD 15.4

LCD SIDE RUBBER 15.4

LCD FRONT RUBBER 15.4

THERMAL DOOR FRONT RUBBER 15.4

THERMAL DOOR RUBBER 15.4

LOWER CASE RUBBER 15.4

THERMAL PAD

NAMEPALTE e-ME510

SCREW

86.AHE02.001

86.AHE02.002

86.AHE02.003

86.AHE02.004

86.AHE02.005

86.AHE02.006

86.AHE02.007

86.AHE02.008

86.AHE02.009

86.AHE02.010

86.AHE02.011

86.AHJ02.006

SCREW,M2.5*3 (Ni-NL)

SCREW,M2.5*6 (NL)

SCREW

SCREW,M2.5*12 (NL)

SCREW

SCREW,M2*2.2

SCREW

SCREW,M2*3 (NL)

SCREW

SCREW,M2*5 (Ni-NL)

SCREW

SCREW,M 2.5D 3.2L K 6D NI +

SCREW,M M 2.0D 3L K 5D NI +

SCREW,F 4# 5L K 4.5D ZK NL + CR3+

SCREW, M2.5X4 (NL)

SCREW

SCREW,M3*3 (NI)

SCREW

CPU THERMAL SCREW ASSY

Chapter 6

171

102

Chapter 6

Vtech Telephone Ls6325 User Manual
Tripp Lite Bp48v18 User Manual
Toshiba Carrier Rav Sp240at2 Ul User Manual
Samsung Digital Laser Mfp Scx 4216f User Manual
Ricoh Lf 125 H915 User Manual
Murphy Lube Level Maintainer Lm2000 User Manual
MAKITA XMT03 User Manual
Lexmark X 954de User Manual
FUJITSU POINT 510 User Manual
ACER ASPIRE 4720Z User Manual