ACER D1P1903 User Manual

Acer Projector  
PL1620n/PL1520i/PL1325W/PL1320W/PL1220/  
SL1520i/SL1320Wn/SL1220n/  
FL162/FL152/FL221A/FL122/FL112/FL152S/  
FL122S/FL112S/  
LU-P200U/LU-P200F/LU-P500WA/LU-P200W/  
LU-P200X/LU-S200F/LU-S200W/LU-S200X/  
PF-L200U/PF-L200F/PF-L500WA/PF-L200W/  
PF-L200X/PS-L200F/PS-L200W/PS-L200X/  
LR630/LR530/LR335/LR330/LR230/LR530S/  
LR330S/LR230S/  
ML-530/ML-430/ML-235/ML-230/ML-130/  
ML-430S/ML-230S/ML-130S/VL6530i  
DWU1902/D1P1903/DWX1904/DNX1905/  
D1P1906/DWX1907/DNX1908  
User’s Guide  
Copyright © 2019. Acer Incorporated.  
All Rights Reserved.  
Acer Projector User’s Guide  
Original Issue: 08/2019  
Information for your safety and comfort  
Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions  
marked on the product.  
Turning the product off before cleaning  
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a  
damp cloth for cleaning.  
Caution for plug as disconnecting device  
Observe the following guidelines when connecting and disconnecting power to the external power supply unit:  
y Install the power supply unit before connecting the power cord to the AC power outlet.  
y Unplug the power cord before removing the power supply unit from the projector.  
y If the system has multiple sources of power, disconnect power from the system by unplugging all power cords  
from the power supplies.  
Caution for Accessibility  
Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the  
equipment operator as possible. When you need to disconnect power to the equipment, be sure to unplug the  
power cord from the electrical outlet.  
Warning!  
y Do not use this product near water.  
y Do not place this product on an unstable cart, stand or table. If the product falls, it could be seriously damaged.  
y Slots and openings are provided for ventilation to ensure reliable operation of the product and to protect it from  
overheating. These openings must not be blocked or covered. The openings should never be blocked by placing  
the product on a bed, sofa, rug or other similar surface.  
y This product should never be placed near or over a radiator or heat register, or in a built-in installation unless  
proper ventilation is provided.  
y Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points  
or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind onto or into the product.  
y To avoid damage of internal components and to prevent battery leakage, do not place the product on a vibrating  
surface.  
y Never use it under sporting, exercising, or any vibrating environment which will probably cause unexpected  
short current or damage rotor devices.  
Using electrical power  
y This product should be operated from the type of power indicated on the marking label. If you are not sure of the  
type of power available, consult your dealer or local power company.  
y Do not allow anything to rest on the power cord. Do not locate this product where people will walk on the cord.  
y If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged  
into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating  
of all products plugged into the wall outlet does not exceed the fuse rating.  
y Do not overload a power outlet, strip or receptacle by plugging in too many devices. The overall system load  
must not exceed 80% of the branch circuit rating. If power strips are used, the load should not exceed 80% of  
the power strip’s input rating.  
y This product’s AC adapter is equipped with a three-wire grounded plug. The plug only fits in a grounded power  
outlet. Make sure the power outlet is properly grounded before inserting the AC adapter plug. Do not insert the  
plug into a non-grounded power outlet. Contact your electrician for details.  
Warning! The grounding pin is a safety feature. Using a power outlet that is not properly grounded may  
result in electric shock and/or injury.  
 otee The grounding pin also provides good protection from unexpected noise produced by other nearby electrical devices  
that may interfere with the performance of this product.  
y Use the product only with the supplied power supply cord set. If you need to replace the power cord set, make  
sure that the new power cord meets the following requirements: detachable type, UL listed/CSA certified, VDE  
approved or its equivalent, 4.5 meters (15 feet) maximum length.  
3
English  
Product servicing  
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous  
voltage points or other risks. Refer all servicing to qualified service personnel.  
Unplug this product from the wall outlet and refer servicing to qualified service personnel when:  
y the power cord or plug is damaged, cut or frayed  
y liquid was spilled into the product  
y the product was exposed to rain or water  
y the product has been dropped or the case has been damaged  
y the product exhibits a distinct change in performance, indicating a need for service  
y the product does not operate normally after following the operating instructions  
 otee Adjust only those controls that are covered by the operating instructions, since improper adjustment of  
other controls may result in damage and will often require extensive work by a qualified technician to  
restore the product to normal condition.  
Warning! For safety reasons, do not use non-compliant parts when adding or changing components.  
Consult your reseller for purchase options.  
Your device and its enhancements may contain small parts. Keep them out of the reach of small children.  
Additional safety information  
y Do not look into the projector’s lens when the light is on. The bright may hurt your eyes.  
y Turn on the projector first and then signal sources  
y Do not place the product in following environments:  
y Space that is poorly ventilated or confined. At least 50cm clearance from walls and free flow of air around the  
projector is necessary.  
y Locations where temperatures may become excessively high, such as inside of a car with all windows rolled up.  
y Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components,  
shortening the life span and darkening the image.  
y Locations near fire alarms.  
y Locations with an ambient temperature above 40ºC / 104ºF.  
y Locations where the altitudes are higher than 10000 feet.  
y Unplug immediately if there is something wrong with your projector. Do not operate if smoke, strange noise  
or odor comes out of your projector. It might cause fire or electric shock. In this case, unplug immediately and  
contact your dealer.  
y Do not keep using this product to break or drop it. In this case contact your dealer for inspection.  
y Do not face the projector lens to the sun. It can lead to fire.  
y When switching the projector off, suggest to ensure the projector completes its cooling cycle before  
disconnecting power.  
y Do not frequently turn off the main power abruptly or unplug the projector during operation. The best way is to  
wait for the fan to turn off before turning main power off.  
y Do not touch air outlet grille and bottom plate which becomes hot.  
y Do not look into the air outlet grille when projector is operating. It may hurt your eyes.  
y Always open the lens shutter or remove the lens cap when the projector is on.  
y Do not block the projector lens with any object when the projector is under operation as this could cause the  
object to become heated and deformed or even cause a fire.  
y Do not attempt to disassemble this projector. There are dangerous high voltages inside which may hurt you.  
Refer servicing only to suitable qualified professional service personnel.  
y Do not stand the projector on end vertically. It may cause the projector to fall over, causing injury or damage.  
y 360° projection capability  
Images can be projected over a full 360° range along the vertical axis, including reproduction on a ceiling or floor.  
360º  
360º  
 otee The brightness will be reduced 80% when the projection direction is downward.  
English  
4
Portrait projection  
Do not use the projector with it leaning to the left and right. This may result in a malfunction, however, portrait  
installation is possible.  
 otee  
Please do not install the projector in a vertical orientation on the top of the floor or table on its own.  
The intake vent may be obstructed, resulting in the projector getting warm and the possibility of fire  
and malfunction occurring.  
When operating the projector in an enclosed space, allow at least 30 cm clearance around the intake  
and exhaust vents.  
Caution for Listening  
To protect your hearing, follow these instructions.  
y Increase the volume gradually until you can hear clearly and comfortably.  
y Do not increase the volume level after your ears have adjusted.  
y Do not listen to music at high volumes for extended periods.  
y Do not increase the volume to block out noisy surroundings.  
y Decrease the volume if you can’t hear people speaking near you.  
Disposal instructions  
Do not throw this electronic device into the trash when discarding. To minimize pollution and  
ensure utmost protection of the global environment, please recycle. For more information on  
the Waste from Electrical and Electronics Equipment (WEEE) regulations, visit http://www.  
acer-group.com/public/Sustainability/sustainability01.htm  
Do not stare into the beam  
Do not stare into beam, RG2  
As with any bright source, do not stare into the direct beam, RG2 IEC 62471-5:2015.  
RG 2  
Notice is given to supervise children and to never allow them  
to stare into the projector beam at any distance from the  
projector.  
Notice is given to use caution when using the remote control  
for starting the projector while in front of the projection lens  
Notice is given to the user to avoid the use of optical aids such  
as binoculars or telescopes inside the beam.  
5
English  
First things first  
Usage  otes  
Doe  
y Turn off the product before cleaning.  
y Use a soft cloth moistened with mild detergent to clean the displayhousing.  
y Disconnect the power plug from AC outlet if the product is not being used for a long period of time.  
Don’te  
y Block the slots and openings on the unit provided for ventilation.  
y Use abrasive cleaners, waxes or solvents to clean the unit.  
y Use under the following conditions:  
y In extremely hot, cold or humid environments.  
y In areas susceptible to excessive dust and dirt.  
y Near any appliance that generates a strong magnetic field.  
y Place In direct sunlight.  
Precautions  
Follow all warnings, precautions and maintenance as recommended in this user’s guide to maximize the life of your  
unit.  
Warning!  
y Do not look into the projector’s lens when the light is on. The bright may hurt your eyes.  
y To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.  
y Please do not open or disassemble the product as this may cause electric shock.  
y When switching the projector off, please ensure the projector completes its cooling cycle before disconnecting  
power.  
y Turn on the projector first and then the signal sources.  
y Do not use lens cap when projector is in operation.  
Cleaning the lens  
y Before cleaning the lens, be sure to turn off the projector and unplug the power cord to allow it to completely  
cool down.  
y Use a compressed air tank to remove the dust.  
y Use a special cloth for cleaning lens and gently wipe the lens. Do not touch the lens with your fingers.  
y Do not use alkaline/acid detergents or volatile solvents such as alcohol for cleaning lens. If the lens is damaged  
due to the cleaning process, it is not covered by the warranty.  
Warning! Do not use a spray containing flammable gases to remove dust or dirt from the lens. This may  
cause a fire due to excessive heat inside the projector.  
Warning! Do not clean the lens if the projector is warming up as this may cause the lens’ surface film to  
peel off.  
Warning! Do not wipe or tap the lens with a hard object.  
English  
6
TABLE OF CO TE TS  
7
English  
INTRODUCTION  
Package Overview  
Carefully unpack and verify that you have the items listed below under standard accessories. Some of the items  
under optional accessories may not be available depending on the model, specification and your region of  
purchase. Please check with your place of purchase. Some accessories may vary from region to region.  
The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.  
Standard accessories  
Warranty Card  
Basic User Manual  
Projector  
Remote control  
Documentation  
CD user manual  
Lens cap  
Optional accessories  
Power lead  
WirelessProjection-Kit  
HDMI cable  
 otee  
Optional accessories vary depending on model, specification and region.  
9
English  
 
INTRODUCTION  
Product Overview  
1
6 5 3  
1 2  
4
11  
7
8
6
12  
8
8
8
5
6
10  
9
 otee  
Do not block projector intake and exhaust vents.  
When operating the projector in an enclosed space, allow at least 30 cm clearance around the intake  
and exhaust vents.  
Functions vary depending on model definition.  
 o.  
Item  
 o.  
7. Ventilation (outlet)  
Tilt-Adjustment Feet  
Item  
1. IR Receivers  
Keypad  
2.  
8.  
3. Lens Shift Dial  
9. Kensington™ Lock Port  
10. Input / Output  
11. Power Socket  
12. Lens  
4. Ventilation (inlet)  
5. Zoom Lever  
6. Focus Ring  
10 English  
 
INTRODUCTION  
Connections  
1 2  
3 4 5 6 7 8  
9 10 11 12  
13  
 o.  
1. HDMI 2 (v1.4) Connector  
Service connector (for firmware upgrade)  
Item  
2.  
3. HDMI 1 (v2.0) / MHL Connector  
4. USB Power Out (5V 1.5A) Connector  
5. Composite Connector  
6. VGA In Connector  
7. Audio In Connector  
8. Audio Out Connector  
9. Power Socket  
10. USB connector (for wifi dongle)  
11. RJ-45 Connector  
12. RS232 Connector  
13. KensingtonTM Lock Port  
 otee Functions vary depending on model definition.  
11  
English  
 
INTRODUCTION  
Keypad  
1
2
3
8
9
4
5
10  
6
7
11  
8
 o.  
1.  
Item  
 o.  
7.  
Item  
Power LED  
Lamp LED  
Menu  
Keystone Correction  
2.  
8.  
3. Temp LED  
9. Information  
4. Power  
10. Enter  
5. Source  
11. Re-Sync  
6. Four directional select keys  
12 English  
 
INTRODUCTION  
Remote control  
26  
1
7
8
2
3
4
9
5
10  
6
11  
19  
20  
21  
12  
13  
14  
15  
16  
17  
18  
22  
23  
24  
25  
Model No:J-25050  
MC.JMV11.009  
 o.  
1. Infrared transmitter  
POWER  
Item  
 o.  
14. PgUp (not supported)  
COMPONENT (not supported)  
Item  
2.  
15.  
3. Laser button  
4. RATIO  
16. PgDn (not supported)  
17. MEDIA (not supported)  
Select/Enter  
5.  
18. KeyPad 0~9  
Play/Pause  
6. Four directional select keys  
7. 3D  
19. MENU  
20. HDMI™/MHL  
21. HIDE  
8. SOURCE  
9. MODE  
22. ZOOM IN  
23. VIDEO  
10. KEYSTONE  
BACK  
11.  
24. ZOOM OUT  
STOP  
12. VGA  
25. LAN/WiFi  
13. FREEZE  
26. Laser pointer  
 otee Some keys may have no function for models that do not support these features.  
13  
English  
 
INTRODUCTION  
MHL (Mobile High-Definition Link) Control  
1
2
3
4
5
 o.  
Item  
Description  
MODE  
Press “MODE” button for one second to activate the MHL  
Control Mode.  
1.  
To exit, press the “MODE” button again.  
Select/Enter  
Press to select/enter the file.  
2.  
3.  
Four directional Use up, down, left, right buttons to select items or make  
select keys  
adjustments to your selection.  
Back/Exit  
Press “BACK” to go back one menu step.  
To exit the file.  
4.  
5. MENU  
Press to launch the root memu.  
 otee Some keys may have no function for models that do not support these features.  
14 English  
 
SETUP A D I STALLATIO  
Installing the projector  
Your projector is designed to be installed in one of four possible positions.  
Your room layout or personal preference will dictate which installation location you select. Take into consideration  
the size and position of your screen, the location of a suitable power outlet, as well as the location and distance  
between the projector and the rest of your equipment.  
Table mount front  
Ceiling mount front  
Table mount rear  
Ceiling mount rear  
Projector should be placed flat on a surface and 90 degrees / perpendicular to the screen.  
How to determine projector location for a given screen size, please refer to distance table on pages  
57-57.  
How to determine screen size for a given distance, please refer to distance table on pages 57-57.  
 otee The further away the projector is placed from the screen the projected image size increases and vertical  
offset also increases proportionally.  
IMPORTANTꢀ  
Do not operate the projector in any orientation other that table top or ceiling mount. The projector should  
be horizontal and not tilted either forwards/backwards or left/right. Any other orientation will invalidate the  
warranty and may shorten the lifetime of the projector light source or the projector itself. For none standard  
installation advise please contact Acer.  
15  
English  
 
SETUP A D I STALLATIO  
Projector installation notice  
 otee The brightness will be reduced 80% when the projection direction is downward.  
225°~315° ±5°  
Portrait mode  
Air outlet side  
10°  
10°  
10° 10°  
10°  
10°  
Allow at least 30 cm clearance around the exhaust vent.  
Minimum 100mm  
(3.94 inches)  
Minimum 300mm  
(11.81 inches)  
Minimum 300mm  
(11.81 inches)  
Minimum 100mm  
(3.94 inches)  
16 English  
SETUP A D I STALLATIO  
Minimum 100mm  
Minimum 100mm  
(3.94 inches)  
(3.94 inches)  
Ensure that the intake vents do not recycle hot air from the exhaust vent.  
When operating the projector in an enclosed space, ensure that the surrounding air temperature within  
the enclosure does not exceed operation temperature while the projector is running, and the air intake  
and exhaust vents are unobstructed.  
All enclosures should pass a certified thermal evaluation to ensure that the projector does not recycle  
exhaust air, as this may cause the device to shutdown even if the enclosure temperature is with the  
acceptable operation temperature range.  
17  
English  
SETUP A D I STALLATIO  
Connecting sources to the projector  
2
2
3
3
10  
10  
USB flash  
drive  
16  
9
10  
Smart devices  
3
5
RCA  
6
4
5
Display  
7
Video Output  
8
2
Speakers  
11  
Screen  
12  
12  
13  
14  
15  
3D IR Emitter  
Audio Output  
1
18 English  
 
SETUP A D I STALLATIO  
#
1
2
3
4
5
6
7
8
9
Description  
Power cord  
Audio cable  
HDMI (MHL) cable  
VGA to component/HDTV adapter  
VGA cable  
3 RCA component cable  
Composite video cable  
RS232 cable  
WirelessHD dongle  
10 Wireless dongle  
11 Wireless remote control  
12 LAN cable  
13 12V DC cable  
14 3D SYNC cable  
15 SPDIF cable  
16 USB flash drive  
 otee  
To ensure the projector works well with your computer, please make sure the timing of the display  
mode is compatible with the projector.  
Functions vary depending on model definition.  
USB cable needs powered extender if the length is over 5 m.  
USB DC 5V out connector support 5V power output for HDMI dongle charging.  
DC 12V out connector support 12V/100mA power for screen control only.  
19  
English  
SETUP A D I STALLATIO  
Adjusting the projector image  
Image height  
The projector is equipped with elevator feet for adjusting the image height.  
1.  
2.  
Locate the adjustable foot you wish to adjust on the underside of the projector.  
Rotate the adjustable foot clockwise or counterclockwise to raise or lower the projector.  
Tilt-Adjustment Feet  
Tilt-Adjustment Ring  
Zoom, lens shift, and focus  
To adjust the image size, turn the zoom lever clockwise or counterclockwise to increase or decrease  
the projected image size.  
To adjust the image position, turn the lens shift dial clockwise or counterclockwise to adjust the  
position of the projected image vertically.  
To adjust the focus, turn the focus ring clockwise or counterclockwise until the image is sharp and  
legible.  
Lens Shift Dial  
Zoom Lever  
Focus Ring  
 otee Ensure that the projection screen is within the required distance from the projector. Please refer  
to “Image size and projection distance” for more information.  
20 English  
   
SETUP A D I STALLATIO  
Remote setup  
Installing / replacing the batteries  
Two AAA size batteries are supplied for the remote control.  
1.  
2.  
3.  
Remove the battery cover on the back of the remote control.  
Insert AAA batteries in the battery compartment as illustrated.  
Replace back cover on remote control.  
 otee Replace only with the same or equivalent type batteries.  
CAUTION  
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.  
Do not mix batteries of different types. Different types of batteries have different characteristics.  
Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or  
cause chemical leakage in old batteries.  
Remove batteries as soon as the are depleted. Chemicals that leak from batteries that come in contact  
with skin can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth.  
The batteries supplied with this product may have a shorter life expectancy due to storage conditions.  
If you will not be using the remote control for an extended period of time, remove the batteries.  
When you dispose of the batteries, you must obey the law in the relative area or country.  
21  
English  
 
SETUP A D I STALLATIO  
Effective range  
Infra-Red (IR) remote control sensor is located on the top and front sides of the projector. Ensure to hold the  
remote control at an angle within 40 degrees perpendicular to the projector’s IR remote control sensor to function  
correctly. The distance between the remote control and the sensor should not be longer than 5 meters (16.4 feet).  
Make sure that there are no obstacles between the remote control and the IR sensor on the projector  
that might obstruct the infra-red beam.  
Make sure the IR transmitter of the remote control is not being shined by sunlight or fluorescent lamps  
directly.  
Please keep the remote controller away from fluorescent lamps for over 2 m or the remote controller  
might become malfunction.  
If the remote control is close to Inverter-Type fluorescent lamps, it might become ineffective from time  
to time.  
If the remote control and the projector are within a very short distance, the remote control might  
become ineffective.  
When you aim at the screen, the effective distance is less than 5 m from the remote control to the  
screen and reflecting the IR beams back to the projector. However, the effective range might change  
according to screens.  
Approx. ±20°  
Approx. ±20°  
22 English  
USING THE PROJECTOR  
Powering on / off the projector  
or  
Lens cap  
Powering on  
1.  
2.  
Remove the lens cap.  
Securely connect the power lead and signal/source cable. When connected, the Power LED will turn  
red.  
3.  
4.  
Turn on the projector by pressing the button on the projector keypad or remote control.  
A start up screen will display in approximately 10 seconds and the Power LED will turn blue.  
 otee The first time the projector is turned on, you will be prompted to select the preferred language, projection  
orientation, and other settings.  
Powering off  
1.  
2.  
Turn off the projector by pressing the button on the projector keypad or remote control.  
The following message will be displayed:  
Power Off  
Power Off?  
Press power key again.  
3.  
4.  
Press the button again to confirm, otherwise the message will disappear after 10 seconds. When  
you press the button for the second time, the projector will shut down.  
When the Power turns solid red, this indicates the projector has entered standby mode. If you wish  
to turn the projector back on, you must wait until the cooling cycle has finished and the projector has  
entered standby mode. When the projector is in standby mode, simply press the button again to  
turn on the projector.  
5.  
Disconnect the power lead from the electrical outlet and the projector.  
 otee It is not recommended that the projector is turned on immediately, right after a power off procedure.  
23  
English  
 
USING THE PROJECTOR  
Selecting an input source  
Turn on the connected source that you want to display on the screen, such as computer, notebook, video player,  
etc. The projector will automatically detect the source. If multiple sources are connected, press the  
button on the  
projector keypad or the Source button on the remote control to select the desired input.  
or  
Lens cap  
24 English  
 
USING THE PROJECTOR  
Menu navigation and features  
The projector has multilingual on-screen display menus that allow you to make image adjustments and change a  
variety of settings. The projector will automatically detect the source.  
1.  
2.  
To open the OSD menu, press the button on the projector keypad or the Menu button on the remote  
control.  
When OSD is displayed, use pq keys to select any item in the main menu. While making a selection  
on a particular page, press the  
control to enter sub menu.  
button on the projector keypad or the Enter button on the remote  
3.  
Use tu keys to select the desired item in the sub menu and then press the  
or Enter button to  
view further settings. Adjust the settings by using tu keys.  
4.  
5.  
6.  
Select the next item to be adjusted in the sub menu and adjust as described above.  
Press press the or Enter button to confirm, and the screen will return to the main menu.  
To exit, press the or Menu button again. The OSD menu will close and the projector will  
automatically save the new settings.  
Settings  
Sub Menu  
Display  
Image Settings  
3D  
Aspect Ratio  
Edge Mask  
Zoom  
Main Menu  
Image Shift  
Keystone  
Select  
Exit  
Enter  
Navigation guide  
25  
English  
 
USING THE PROJECTOR  
OSD Menu tree  
Main  
Menu  
Sub Menu  
Sub Menu 2  
Sub Menu 3  
Sub Menu 4  
Values  
Presentation  
Bright  
HDR SIM.  
HLG SIM.  
Cinema  
Game  
Display Mode  
sRGB  
DICOM SIM.  
User  
3D  
Off [Default]  
Blackboard  
Light Yellow  
Light Green  
Light Blue  
Pink  
Wall Color  
Gray  
Display  
Image Settings Brightness  
-50 ~ 50  
-50 ~ 50  
1 ~ 15  
Contrast  
Sharpness  
Color  
-50 ~ 50  
-50 ~ 50  
Tint  
Film  
Video  
Graphics  
Standard(2.2)  
Gamma  
1.8  
2.0  
2.4  
2.6  
BrilliantColorTM  
1 ~ 10  
Warm  
Standard  
Cool  
Color Settings  
Color  
Temperature  
Cold  
26 English  
 
USING THE PROJECTOR  
Main  
Menu  
Sub Menu  
Sub Menu 2  
Sub Menu 3  
Sub Menu 4  
Values  
Red [Default]  
Green  
Blue  
Color  
Cyan  
Yellow  
Magenta  
White(*)  
Color Matching  
Hue / R(*)  
-50 ~ 50 [Default: 0]  
-50 ~ 50 [Default: 0]  
-50 ~ 50 [Default: 0]  
Cancel [Default]  
Yes  
Saturation / G(*)  
Gain / B(*)  
Reset  
Exit  
Red Gain  
Green Gain  
Blue Gain  
Red Bias  
Green Bias  
Blue Bias  
-50 ~ 50  
-50 ~ 50  
-50 ~ 50  
-50 ~ 50  
-50 ~ 50  
-50 ~ 50  
Cancel [Default]  
Yes  
Color Settings  
RGB Gain/Bias  
Reset  
Exit  
Display  
Image Settings  
Auto [Default]  
RGB  
Color Space [Not  
HDMI Input]  
YUV  
Auto [Default]  
RGB(0~255)  
RGB(16~235)  
YUV  
Color Space  
[HDMI Input]  
Off  
Automatic  
On [Default]  
-10 ~ 10 (depends on signal)  
[Default: 0]  
Frequency  
Phase  
0~31 (depends on signal)  
[Default: 0]  
Signal  
-5 ~ 5 (depends on signal)  
[Default: 0]  
H. Position  
V. Position  
-5 ~ 5 (depends on signal)  
[Default: 0]  
DynamicBlack  
Eco.  
Power  
Brightness Mode  
Reset  
(Power = 100%/ 95%/ 90%/ 85%/  
80%/ 75%/ 70%/ 65%/ 60%/ 55%/  
50%)  
27  
English  
USING THE PROJECTOR  
Main  
Menu  
Sub Menu  
Sub Menu 2  
Sub Menu 3  
Sub Menu 4  
Values  
Off [Default]  
3D Mode  
On  
3D [Default]  
L
3D 2D  
R
3D  
Auto [Default]  
SBS  
3D Format  
Top and Bottom  
Frame Sequential  
On  
3D Sync Invert  
Off [Default]  
4:3  
16:9  
Display  
16:10  
Aspect Ratio  
LBX  
Native  
Auto [Default]  
0 ~ 10 [Default: 0]  
-5 ~ 25  
Edge Mask  
Zoom  
-100 ~ 100 [Default: 0]  
-100 ~ 100 [Default: 0]  
H
Image Shift  
V
Four Corners  
H Keystone  
V Keystone  
-30 ~30 / -15 ~ 15 [Default: 0]  
-30 ~30 / -15 ~ 15 [Default: 0]  
Off  
Geometric  
Correction  
Auto Keystone  
Reset  
On [Default]  
Off [Default]  
On  
Mute  
Audio  
Volume  
0 ~ 10 [Default: 5]  
28 English  
USING THE PROJECTOR  
Main  
Menu  
Sub Menu  
Sub Menu 2  
Sub Menu 3  
Sub Menu 4  
Values  
Front  
Rear  
[Default]  
Projection  
Ceiling-top  
Rear-top  
16:9  
Screen Type  
16:10 [Default]  
Off [Default]  
On  
Direct Power On  
Signal Power On  
Off [Default]  
On  
Auto Power Off  
(min.)  
0 ~ 180 (5 min increments)  
[Default: 20]  
Power Settings  
Active  
Power Mode  
(Standby)  
Eco [Default]  
Off [Default]  
On  
Setup  
USB Power  
(Standby)  
Off [Default]  
On  
Security  
Month  
Security  
Security Timer  
Day  
Hour  
Change  
Password  
[Default: 1234]  
Off [Default]  
On  
HDMI CEC  
Green Grid  
Magenta Grid  
White Grid  
White  
Test Pattern  
Off [Default]  
29  
English  
USING THE PROJECTOR  
Main  
Menu  
Sub Menu  
Sub Menu 2  
Sub Menu 3  
Sub Menu 4  
Values  
English [Default]  
Deutsch  
Français  
Italiano  
Español  
Português  
Polski  
Nederlands  
Svenska  
Norsk  
Suomi  
ελληνικά  
繁體中文  
简体中文  
日本語  
Language  
한국어  
Русский  
Magyar  
Čeština  
Setup  
Options  
ไทย  
Türkçe  
Tiếng Việt  
Bahasa Indonesia  
Română  
Slovenčina  
CC1  
Closed  
Captioning  
CC2  
Off [Default]  
Top left  
Top right  
Menu Location  
Menu Timer  
Center  
[Default]  
Bottom left  
Menu Settings  
Bottom right  
Off  
5sec  
10sec [Default]  
Off [Default]  
On  
Auto Source  
30 English  
USING THE PROJECTOR  
Main  
Menu  
Sub Menu  
Sub Menu 2  
Sub Menu 3  
Sub Menu 4  
Values  
HDMI 1/MHL [Default]  
HDMI 2  
Input Source  
VGA IN  
Video  
Wireless Mirroring  
Off [Default]  
On  
High Altitude  
Logo  
Default [Default]  
Neutral  
Options  
Setup  
User  
Black [Default]  
Blue  
Red  
Background  
Color  
Green  
Gray  
Logo  
Cancel [Default]  
Yes  
Reset  
Reset to Default  
Network Status  
MAC Address  
(read only)  
(read only)  
Off  
DHCP  
On [Default]  
LAN  
IP Address  
Subnet Mask  
Gateway  
DNS  
Reset  
Off  
Crestron  
Extron  
On [Default]  
 otee Port 41794  
Off  
Network  
On [Default]  
 otee Port 2023  
Off  
PJ Link  
On [Default]  
 otee Port 4352  
Control  
Off  
AMX Device  
Discovery  
On [Default]  
 otee Port 9131  
Off  
Telnet  
HTTP  
On [Default]  
 otee Port 23  
Off  
On [Default]  
 otee Port 80  
31  
English  
USING THE PROJECTOR  
Main  
Menu  
Sub Menu  
Sub Menu 2  
Sub Menu 3  
Sub Menu 4  
Values  
Serial Number  
Source  
Resolution  
00x00  
Refresh Rate  
Display Mode  
0.00Hz  
Power Mode  
(Standby)  
Light Source  
Hours  
Info  
0 hr  
Network Status  
IP Address  
Brightness  
Mode  
System  
LAN  
FW Version  
MCU  
 otee Functions vary depending on model definition.  
32 English  
USING THE PROJECTOR  
Display menu  
Display image settings menu  
 otee Functions vary depending on model definition.  
Display Mode  
There are many factory presets optimized for various types of images.  
Presentation: This mode is suitable for showing in front of public in connection to the PC.  
Bright: Maximum brightness from PC input.  
HDR SIM.: Decodes and displays High Dynamic Range (HDR) content for the deepest blacks,  
brightest whites, and vivid cinematic color using REC.2020 color gamut. This mode can be selected to  
enhances non-HDR content with simulated High Dynamic Range (HDR).  
HLG SIM.: Decodes and displays Hybrid Log Gamma(HLG) content for the deepest blacks, brightest  
whites, and vivid cinematic color using REC.2100 color gamut. This mode can be selected to  
enhances non-HLG content with simulated Hybrid Log Gamma(HLG).  
Cinema: Provides the best colors for watching movies.  
Game: Select this mode to increase the brightness and response time level for enjoying video games.  
sRGB: Standardized accurate color.  
DICOM SIM.: This mode can project a monochrome medical image such as an X ray radiography,  
MRI, etc.  
User: Memorize user’s settings.  
3D: To experience the 3D effect, you need to have 3D glasses, make sure your PC/portable device  
has a 120 Hz signal output quad buffered graphics card and have a 3D Player installed.  
Wall Color  
Use this function to obtain an optimized screen image according to the wall color. Select between off, blackboard,  
light yellow, light green, light blue, pink, and gray.  
Brightness  
Adjust the brightness of the image.  
Contrast  
The contrast controls the degree of difference between the lightest and darkest parts of the picture.  
Sharpness  
Adjust the sharpness of the image.  
Color  
Adjust a video image from black and white to fully saturated color.  
Tint  
Adjust the color balance of red and green.  
Gamma  
Set up gamma curve type. After the initial setup and fine tuning is completed, utilize the Gamma Adjustment steps  
to optimize your image output.  
Film: For home theater.  
Video: For video or TV source.  
Graphics: For PC / Photo source.  
Standard(2.2): For standardized setting.  
33  
English  
 
USING THE PROJECTOR  
1.8 / 2.0 / 2.4 / 2.6: For specific PC / Photo source.  
 otee  
These options are only available if the 3D mode function is disabled, the Wall Color setting is not set  
to Blackboard, and the Display Mode setting is not set to DICOM SIM., HDR SIM. or HLG SIM.  
In 3D mode, user can only select 3D for Gamma setting.  
If the Wall Color setting is set to Blackboard, user can only select Blackboard for Gamma setting.  
If the Display Mode setting is set to DICOM SIM., user can only select DICOM SIM. for Gamma  
setting.  
If the Display Mode setting is set to HDR SIM. or HLG SIM., user can only select HDR SIM. or HLG  
SIM. for Gamma setting.  
Color Settings  
Configure the color settings.  
BrilliantColorTM: This adjustable item utilizes a new color-processing algorithm and enhancements to  
enable higher brightness while providing true, more vibrant colors in picture.  
Color Temperature: Select a color temperature from Warm, Standard, Cool, or Cold.  
Color Matching: Select the following options:  
±
±
Color: Adjust the red, green, black, cyan, yellow, magenta, and white level of the image.  
Hue / R(red)*: Adjust the color balance of red and green.  
 otee *If the Color setting is set to White, you can adjust the red color setting.  
±
±
Saturation / G(green)*: Adjust a video image from black and white to fully saturated color.  
 otee *If the Color setting is set to White, you can adjust the green color setting.  
Gain / B(blue)*: Adjust the image brightness.  
 otee *If the Color setting is set to White, you can adjust the blue color setting.  
±
±
Reset: Return the factory default settings for color matching.  
Exit: Exit the “Color Matching” menu.  
RGB Gain/Bias: This settings allows to configure the brightness (gain) and contrast (bias) of an  
image.  
±
±
Reset: Return the factory default settings for RGB gain/bias.  
Exit: Exit the “RGB Gain/Bias” menu.  
Color Space (non-HDMI input only): Select an appropriate color matrix type from the following:  
AUTO, RGB, or YUV.  
Color Space (HDMI input only): select an appropriate color matrix type from the following: Auto,  
RGB(0-255), RGB(16-235), and YUV.  
Signal  
Adjust the signal options.  
Automatic: Configure automatically the signal (the frequency and phase items are grayed out). If  
automatic is disabled, the frequency and phase items will appear for tuning and saving the settings.  
Frequency: Change the display data frequency to match the frequency of your computer’s graphic  
card. Use this function only if the image appears to flicker vertically.  
Phase: Synchronize the signal timing of the display with the graphic card. If the image appears to be  
unstable or flickers, use this function to correct it.  
H. Position: Adjust the horizontal positioning of the image.  
V. Position: Adjust the vertical positioning of the image.  
 otee This menu is only available if the input source is RGB/Component.  
34 English  
USING THE PROJECTOR  
Brightness Mode  
Adjust the brightness mode settings.  
DynamicBlack: Use to automatically adjust the picture brightness in order to give optimum contrast  
performance.  
Eco.: Choose “Eco.” to dim the projector lamp which will lower power consumption and extend the  
lamp life.  
Power: Choose the power percentage for brightness mode.  
Reset  
Return the factory default settings for color settings.  
Display 3D menu  
 otee  
This projector is a 3D ready projector with DLP-Link 3D solution.  
Please make sure your 3D glasses are use for DLP-Link 3D before enjoy your video.  
This projector supports frame sequential (page-flip) 3D via HDMI/VGA ports.  
To enable 3D mode, the input frame rate should be set to 60Hz only, lower or higher frame rate is not  
supported.  
To reach the best performance, resolution 1920x1080 is recommended, please be noted that 4K  
(3840x2160) resolution is not supported in 3D mode.  
3D Mode  
Use this option to disable the 3D function or select the appropriate the 3D function.  
Off: Select “Off” to turn off 3D mode.  
One Select “On” to turn on 3D mode.  
 otee If the 2D and 3D sources enter projector at the same time, if the ghosting image appears in the 2D source,  
make sure to manually turn off the 3D function.  
3D → 2D  
Use this option to specify how the 3D content should appear on the screen.  
3De Display 3D signal.  
L (Left): Display the left frame of 3D content.  
R (Right): Display the right frame of 3D content.  
3D Format  
Use this option to select the appropriate 3D format content.  
Auto: When a 3D identification signal is detected, the 3D format is selected automatically.  
SBS: Display 3D signal in “Side-by-Side” format.  
Top and Bottom: Display 3D signal in “Top and Bottom” format.  
Frame Sequential: Display 3D signal in “Frame Sequential” format.  
3D Sync Invert  
Use this option to enable/disable the 3D sync invert function.  
35  
English  
 
USING THE PROJECTOR  
Display aspect ratio menu  
Aspect Ratio  
Select the aspect ratio of the displayed image between the following options:  
4e3: This format is for 4:3 input sources.  
16e9: This format is for 16:9 input sources, like HDTV and DVD enhanced for Wide screen TV.  
16e10 (for WXGA/WUXGA model only): This format is for 16:10 input sources, like widescreen laptops.  
LBX: This format is for non-16x9, letterbox source and if you use external 16x9 lens to display 2.35:1  
aspect ratio in full resolution.  
Native: This format displays the original image without any scaling.  
Auto: Automatically selects the appropriate display format.  
 otee  
Detailed informations about LBX mode:  
±
±
Some Letter-Box Format DVDs are not enhanced for 16x9 TVs. In this situation, the image  
will not look right when displaying image in 16:9 mode. In this situation, please try to use the  
4:3 mode to view the DVD. If the content is not 4:3, there will be black bars around the image  
in 16:9 display. For this type of content, you can use LBX mode to fill the image on the 16:9  
display.  
If you use an external anamorphic lens, this LBX mode also allows you to watch a 2.35:1  
content (include Anamorphic DVD and HDTV film source) that supports anamorphic wide is  
enhanced for 16x9 Display in a wide 2.35:1 image. In this case, there are no black bars. Light  
source power and vertical resolution are fully utilized.  
To use the superwide format, do the following:  
a)  
b)  
c)  
Set the screen aspect ratio to 2.0:1.  
Select “Superwide” format.  
Align the projector image correctly on the screen.  
XGA scaling table:  
16e9 screen  
4x3  
480i/p  
576i/p  
1080i/p  
720p  
PC  
Scale to 1024x768.  
Scale to 1024x576.  
16x9  
Native  
Auto  
No scaling will be made; the image is displayed with the resolution based on input source.  
- If source is 4:3, the screen type will be scaled to 1024 x 768.  
- If source is 16:9, the screen type will be scaled to 1024 x 576.  
- If source is 15:9, the screen type will be scaled to 1024 x 614.  
- If source is 16:10, the screen type will be scaled to 1024 x 640.  
XGA auto mapping rule:  
Input resolution  
Auto/Scale  
Auto  
H-resolution  
V-resolution  
480  
1024  
1024  
1024  
1024  
1024  
768  
768  
768  
768  
768  
640  
800  
600  
4:3  
1024  
1600  
768  
1200  
36 English  
 
USING THE PROJECTOR  
1280  
1280  
1280  
720  
720  
1024  
1024  
1024  
1024  
1024  
1024  
1024  
576  
614  
640  
576  
576  
576  
576  
Wide Laptop  
768  
800  
576  
480  
720  
1080  
SDTV  
HDTV  
720  
1280  
1920  
WXGA scaling table (screen type 16x10):  
 otee  
Supported screen type 16:9 (1280x720), 16:10 (1280x800).  
When screen type is 16:9, the 16x10 format becomes unavailable.  
When screen type is 16:10, the 16x9 format becomes unavailable.  
If you select auto option then the display mode will be also automatically changed.  
16 e 10 screen  
4x3  
480i/p  
576i/p  
1080i/p  
720p  
PC  
Scale to 1066x800.  
Scale to 1280x800.  
16x10  
LBX  
Scale to 1280x960, then get the central 1280x800 image to display.  
Native mode  
1:1 mapping centered.  
1:1 mapping  
display  
1280x720  
centered.  
1:1 mapping  
centered.  
1280x800.  
Auto  
-Input source will be fit into 1280x800 display area and be kept its original aspect ratio.  
-If source is 4:3, the screen type will be scaled to 1066x800.  
-If source is 16:9, the screen type will be scaled to 1280x720.  
-If source is 15:9, the screen type will be scaled to 1280x768.  
-If source is 16:10, the screen type will be scaled to 1280x800.  
WXGA auto mapping rule (screen type 16x10):  
Input resolution  
Auto/Scale  
Auto  
H-resolution  
640  
V-resolution  
1280  
1066  
1066  
1066  
1066  
1066  
1066  
1280  
1280  
1280  
1280  
1280  
1280  
1280  
800  
800  
800  
800  
800  
800  
800  
720  
768  
800  
720  
720  
720  
720  
480  
600  
800  
1024  
1280  
1400  
1600  
1280  
1280  
1280  
720  
768  
4:3  
1024  
1050  
1200  
720  
Wide Laptop  
768  
800  
576  
SDTV  
HDTV  
720  
480  
1280  
1920  
720  
1080  
37  
English  
USING THE PROJECTOR  
WXGA scaling table (screen type 16x9):  
16 e 9 screen  
4x3  
480i/p  
576i/p  
1080i/p  
720p  
PC  
Scale to 960x720.  
Scale to 1280x720.  
16x9  
LBX  
Scale to 1280x960, then get the central 1280x720 image to display.  
Native mode  
1:1 mapping centered.  
1:1 mapping  
display  
1280x720  
centered.  
1:1 mapping  
centred.  
1280x720.  
Auto  
-If this format is select, screen type will automatically become 16:9 (1280x720).  
-If source is 4:3, the screen type will be scaled to 960x720.  
-If source is 16:9, the screen type will be scaled to 1280x720.  
-If source is 15:9, the screen type will be scaled to 1200x720.  
-If source is 16:10, the screen type will be scaled to 1152x720.  
WXGA auto mapping rule (screen type 16x9):  
Input resolution  
Auto/Scale  
Auto  
H-resolution  
640  
V-resolution  
1280  
960  
720  
720  
720  
720  
720  
720  
720  
720  
720  
720  
720  
720  
720  
720  
480  
600  
800  
960  
1024  
1280  
1400  
1600  
1280  
1280  
1280  
720  
768  
960  
4:3  
1024  
1050  
1200  
720  
960  
960  
960  
1280  
1200  
1152  
1280  
1280  
1280  
1280  
Wide Laptop  
768  
800  
576  
SDTV  
HDTV  
720  
480  
1280  
1920  
720  
1080  
1080p scaling table:  
16e9 screen  
480i/p  
576i/p  
1080i/p  
720p  
PC  
4x3  
16x9  
Scale to 1440x1080.  
Scale to 1920x1080.  
LBX  
Scale to 1920x1440, then get the central 1920x1080 image to display.  
- 1:1 mapping centered.  
Native mode  
- No scaling will be made; the image is displayed with the resolution based on input source.  
- If auto format is selected, the screen type will automatically become16:9 (1920x1080).  
- If source is 4:3, the screen type will be scaled to 1440 x1080.  
Auto  
- If source is 16:9, the screen type will be scaled to 1920x1080.  
- If source is 16:10, the screen type will be scaled to 1920x1200 and cut 1920x1080 area to  
display.  
38 English  
USING THE PROJECTOR  
1080p auto mapping rule:  
Input resolution  
Auto/Scale  
Auto  
H-resolution  
640  
V-resolution  
1920  
1440  
1440  
1440  
1440  
1440  
1440  
1920  
1800  
1728  
1350  
1620  
1920  
1920  
1080  
1080  
1080  
1080  
1080  
1080  
1080  
1080  
1080  
1080  
1080  
1080  
1080  
1080  
480  
600  
800  
1024  
1280  
1400  
1600  
1280  
1280  
1280  
720  
768  
4:3  
1024  
1050  
1200  
720  
Wide Laptop  
768  
800  
576  
SDTV  
HDTV  
720  
480  
1280  
1920  
720  
1080  
Display edge mask menu  
Edge Mask  
Use this function to remove the video encoding noise on the edge of video source.  
Display zoom menu  
Zoom  
Use to reduce or magnify an image on the projection screen.  
Display image shift menu  
Image Shift  
Adjust the projected image position horizontally (H) or vertically (V).  
Display geometric correction menu  
Four Corners  
Allow the image to be squeezed to fit an area defined by moving each of the four corners’ x and y position.  
H Keystone  
Adjust image distortion horizontally and make a squarer image. Horizontal keystone is used to correct a keystoned  
image shape in which the left and right borders of the image are unequal in length. This is intended for use with  
horizontally on-axis applications.  
V Keystone  
Adjust image distortion vertically and make a squarer image. Vertical keystone is used to correct a keystoned  
image shape in which the top and bottom are slanted to one of the sides. This is intended when for use with  
vertically on-axis applications.  
Auto Keystone  
Correct keystone digitally to fit the projected image on the area on which you are projecting.  
39  
English  
 
USING THE PROJECTOR  
 otee  
The image size will reduce slightly when adjusting the horizontal and vertical keystone.  
When the Auto Keystone is used, the Four Corner Adjustment function will be disabled.  
Reset  
Return the factory default settings for keystone settings.  
Audio menu  
 otee Functions vary depending on model definition.  
Audio mute menu  
Mute  
Use this option to temporarily turn off the sound.  
One Choose “On” to turn mute on.  
Off: Choose “Off” to turn mute off.  
 otee “Mute” function affects both internal and external speaker volume.  
Audio volume menu  
Volume  
Adjust the volume level.  
40 English  
 
USING THE PROJECTOR  
Setup menu  
 otee Functions vary depending on model definition.  
Setup projection menu  
Projection  
Select the preferred projection between front, rear, ceiling-top, and rear-top.  
Setup screen type menu  
Screen Type (for WXGA/WUXGA model only)  
Choose the screen type from 16:9 and 16:10.  
Setup power settings menu  
Direct Power On  
Choose “On” to activate Direct Power mode. The projector will automatically power on when AC power is supplied,  
without pressing the “Power” key on the projector keypad or on the remote control.  
Signal Power On  
Choose “On” to activate Signal Power mode. The projector will automatically power on when a signal is detected,  
without pressing the “Power” key on the projector Keypad or on the remote control.  
 otee Only supported on HDMI 1, HDMI 2 and VGA In Connector.  
Auto Power Off (min.)  
Sets the countdown timer interval. The countdown timer will start, when there is no signal being sent to the  
projector. The projector will automatically power off when the countdown has finished (in minutes).  
Power Mode (Standby)  
Set the power mode setting.  
Active: Choose “Active” to return to normal standby.  
Ecoe Choose “Eco.” to save power dissipation further < 0.5W.  
USB Power (Standby)  
Enable or disable the USB power function when the projector is in standby mode.  
Setup security menu  
Security  
Enable this function to prompt for a password before using the projector.  
One Choose “On” to use security verification when the turning on the projector.  
Off: Choose “Off” to be able to switch on the projector without password verification.  
Security Timer  
Can be select the time (Month/Day/Hour) function to set the number of hours the projector can be used. Once this  
time has elapsed you will be requested to enter your password again.  
Change Password  
Use to set or modify the password that is prompted when turning the projector on.  
 otee Password default value is “1234” (first time).  
41  
English  
 
USING THE PROJECTOR  
Setup HDMI Link settings menu  
 otee  
When you connect HDMI CEC-compatible devices to the projector with HDMI cables, you can control  
them on the same power on or power off status using the HDMI Link control feature in the projector’s  
OSD. This lets one device or multiple devices in a group power on or power off via HDMI Link Feature  
in a typical configuration, your DVD player may be connected to the projector through an amplifier or  
home theater system.  
HDMI  
HDMI  
Amplifier  
DVD Player  
HDMI CEC  
Default is Off. Select “On” to enable HDMI CEC function.  
Setup test pattern menu  
Test Pattern  
Select the test pattern from green grid, magenta grid, white grid, white or disable this function (off).  
42 English  
 
USING THE PROJECTOR  
Setup options menu  
Language  
Select the multilingual OSD menu.  
Closed Captioning  
Closed Captioning is a text version of the program sound or other information displayed on the screen. If the input  
signal contains closed captions, you can turn on the feature and watch the channels. The available options include  
“Off”, “CC1”, and “CC2”.  
Menu Settings  
Set the menu location on the screen and configure menu timer settings.  
Menu Location: Select the menu location on the display screen.  
Menu Timer: Set the duration where the OSD menu stays visible on the screen.  
Auto Source  
Choose this option to let the projector automatically find an available input source.  
Input Source  
Select the input source between HDMI1, HDMI2, VGA IN, VIDEO and Wireless Mirroring.  
High Altitude  
When “On” is selected, the fans will spin faster. This feature is useful in high altitude areas where the air is thin.  
Logo  
Use this function to set the desired startup screen. If changes are made, they will take effect the next time the  
projector is powered on.  
Default: The default startup screen.  
Neutral: Logo is not displayed on startup screen.  
Usere Use the stored picture as the startup screen.  
Screen capture by PC tool  
1.  
Set “Logo” to “User”  
Set the “Logo” to “User” in Setup options menu.  
2.  
Enter download mode  
Hold both “Power” and “Menu” buttons and then plug in power cord. Release the buttons until Power/  
Lamp/Temp LED indicators are lighting red.  
3.  
Connect USB cable between PC and projector  
Please find the “SERVICE” USB port and plug-in USB cable.  
USB  
4.  
Copy and Click Splash Downloader  
Copy the Acer_Splash_Downloader folder from the CD (User’s Guide) to your computer, click the  
43  
English  
 
USING THE PROJECTOR  
Acer_Splash_Downloader.exe program, and follow the on-screen instructions. If the message says  
“Projector found”, the projector has been connected successfully.  
 otee If “Error: No Projector found.”, the projector is not connected. Please retry step 2 and step 3.  
5.  
6.  
Select logo file  
Click the “Browse” button and select logo file. The recommended resolution of logo should not exceed  
the default logo resolution (For example, logo resolution is 1920x1200). The purpose is that keeping  
the quality of the image. If not, the logo may be blurred.  
 otee Support “PNG” & “BMP” file format.  
Download logo to projector  
Click the “Flash Image” button. If the file was written to projector successfully, the message “Download  
Complete” will be displayed on the screen.  
7.  
8.  
Reboot projector  
Plug-out the power cord of projector and plug-in it. Please ensure that the logo has been upgraded  
correctly.  
Operating system compatibility  
Operating system platform  
Windows XP  
compatible  
Not support  
Support  
Windows 7 (64 bit)  
Windows 10 (64 bit)  
Mac OS  
Support  
Not support  
Background Color  
Use this function to display a blue, red, green, gray color, black, or logo screen when no signal is available.  
Setup reset OSD menu  
Reset to Default  
Return the factory default settings for all settings except network setting.  
44 English  
 
USING THE PROJECTOR  
Network menu  
 otee Functions vary depending on model definition.  
Network LAN menu  
Network Status  
Display the network connection status (read-only).  
MAC Address  
Display the MAC address (read-only).  
DHCP  
Use this option to enable or disable the DHCP function.  
Off: To assign IP, subnet mask, gateway, and DNS configuration manually.  
On: Projector will obtain an IP address automatically from your network.  
 otee Exiting OSD will automatically apply the entered values.  
IP Address  
Display the IP address.  
Subnet Mask  
Display subnet mask number.  
Gateway  
Display the default gateway of the network connected to the projector.  
D S  
Display the DNS number.  
How to use web browser to control your projector  
1.  
2.  
Turn “On” the DHCP option on projector to allow a DHCP server to automatically assign an IP address.  
Open the web browser in your PC and type in the projector’s IP address (“Network > LAN > IP  
Address”).  
3.  
Enter the user name and password, and click “Login”.  
The projector’s configuration web interface opens.  
 otee  
The default user name and password is “admin”.  
The steps in this section is based on Windows 7 operating system.  
45  
English  
 
USING THE PROJECTOR  
Making a direct connection from your computer to the projector*  
1.  
2.  
3.  
Turn “Off” the DHCP option on the projector.  
Configure the IP address, Subnet Mask, Gateway, and DNS on projector (“Network > LAN”).  
Open Network and Sharing Center page on your PC, and assign the identical network parameters to  
your PC as set on projector. Click “OK” to save the parameters.  
4.  
Open the web browser on your PC and type in to the URL field the IP address, assigned in step 3.  
Then press “Enter” key.  
Reset  
Reset all values for LAN parameters.  
Network control menu  
Crestron  
Use this function to select the network function (port: 41794).  
Extron  
Use this function to select the network function (port: 2023).  
PJ Link  
Use this function to select the network function (port: 4352).  
AMX Device Discovery  
Use this function to select the network function (port: 9131).  
Telnet  
Use this function to select the network function (port: 23).  
HTTP  
Use this function to select the network function (port: 80).  
46 English  
 
USING THE PROJECTOR  
Setup network control settings menu  
LAN_RJ45 function  
For simplicity and ease of operation, the projector provides diverse networking and remote management features.  
The LAN / RJ45 function of the projector through a network, such as remotely manage: Power On / Off, brightness,  
and contrast settings. Also, you can view the projector status information, such as: Video- Source, Sound-Mute, etc.  
Projector  
(Ethernet)  
Wired LAN terminal functionalities  
This projector can be controlled by using a PC (laptop) or other external device via LAN / RJ45 port and compatible  
with Crestron / Extron / AMX (Device -Discovery) / PJLink.  
Crestron is a registered trademark of Crestron Electronics, Inc. of the United States.  
Extron is a registered trademark of Extron Electronics, Inc. of the United States.  
AMX is a registered trademark of AMX LLC of the United States.  
PJLink applied for trademark and logo registration in Japan, the United States of America, and other  
countries by JBMIA.  
The projector is supported by the specified commands of the Crestron Electronics controller and related software,  
for example RoomView®.  
This projector is compliant to support Extron device(s) for reference.  
This projector is supported by AMX ( Device Discovery ).  
This projector supports most commands of PJLink Class1/2 (Version 1.00/2.00)  
For more detailed information about the various types of external devices which can be connected to the LAN /  
RJ45 port and remote control the projector, as well as the supported commands for these external devices, please  
contact the Support-Service directly.  
47  
English  
 
USING THE PROJECTOR  
HOW TO CREAT YOUR NETWORK ACCOUNT FOR WEB CONTROL  
LAN RJ45  
1.  
Connect an RJ45 cable to RJ45 ports on the projector and the PC (laptop).  
2.  
On the PC (Laptop), select Start > Control Panel > Network Connections.  
3.  
Right-click on the Local Area Connection, and select Property.  
4.  
In the Properties window, select the General tab, and select Internet Protocol (TCP / IP).  
48 English  
 
USING THE PROJECTOR  
5.  
Click “Properties”.  
6.  
Type in the IP address and Subnet mask, then press “OK”.  
7.  
8.  
9.  
Press the “Menu” button on the projector.  
Open on projector Network > LA .  
Enter the following connection parameters:  
±
±
±
±
±
DHCP: Off  
IP Address: 192.168.0.100  
Subnet Mask: 255.255.255.0  
Gateway: 192.168.0.254  
DNS: 192.168.0.51  
10. Press “Enter” to confirm settings.  
11.  
Open a web browser, for example Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher  
installed.  
12. In the Address bar, input the projector’s IP address: 192.168.0.100.  
13. Press “Enter”. (The default user name and password is “admin”.)  
49  
English  
USING THE PROJECTOR  
The projector is setup for remote management. The LAN / RJ45 function displays as follows:  
Information page  
Main page  
Tool page  
Contact IT helpdesk  
50 English  
USING THE PROJECTOR  
RS232 by Telnet Function  
There is alternative RS232 command control way, in projector so called “RS232 by TELNET” for LAN / RJ45  
interface.  
Quick Start-Guide for “RS232 by Telnet”  
Check and get the IP address on OSD of the projector.  
Make sure that the PC / laptop can access the web-page of the projector.  
Make sure that “Windows Firewall” setting is set disabled in case of “TELNET” function filtering out by  
PC / laptop.  
Windows 7  
Windows 10  
1.  
Select Start > All Programs.> Accessories > Command Prompt.  
Windows 7  
Windows 10  
2.  
3.  
Input the command format as follows:  
±
±
telnet ttt.xxx.yyy.zzz 23 (“Enter” key pressed)  
(ttt.xxx.yyy.zzz: IP-Address of the projector)  
If Telnet-Connection ready, and user can have RS232 command input, then “Enter” key pressed, the  
RS232 command will be workable.  
How to have TELNET enabled in Windows 7 / 8 /10  
By default installation for Windows 7 / 8 / 10, “TELNET” function is not included. But end-user can have it by  
way of “Turn Windows features On or Off” to be enabled.  
51  
English  
USING THE PROJECTOR  
Open “Control Panel” in Windows 7 / 8 / 10.  
Windows 7  
Windows 10  
Open “Programs”  
Windows 7  
Windows 10  
Select “Turn Windows features on or off” to open.  
Windows 7  
Windows 10  
Have “Telnet Client” option checked, then press “OK” button.  
52 English  
USING THE PROJECTOR  
Specification for “RS232 by TELNET”:  
1.  
2.  
3.  
4.  
5.  
Telnet: TCP.  
Telnet port: 23 (for more detail, kindly please get contact with the service agent or team).  
Telnet utility: Windows “TELNET.exe” (console mode).  
Disconnection for RS232-by-Telnet control normally: Close  
Windows Telnet utility directly after TELNET connection ready.  
±
±
±
Limitation 1 for Telnet-Control: there is less than 50 bytes for successive network payload for  
Telnet-Control application.  
Limitation 2 for Telnet-Control: there is less than 26 bytes for one complete RS232 command for  
Telnet-Control.  
Limitation 3 for Telnet-Control: Minimum delay for next RS232 command must be more than 200 (ms).  
Info menu  
 otee Functions vary depending on model definition.  
Info menu  
View the projector information as listed below:  
Serial Number  
Source  
Resolution  
Refresh Rate  
Display Mode  
Power Mode (Standby)  
Light Source Hours  
Network Status  
IP Address  
Brightness Mode  
FW Version  
53  
English  
 
ADDITIONAL INFORMATION  
Compatible resolutions  
Digital compatibility  
Digital (HDMI 1.4)  
B0 / Detail Timing  
WXGA:  
B0 / Established  
B0 / Standard Timing  
B1 / Video Mode  
B1 / Detail Timing  
Timing  
720 x 400 @ 70Hz  
640 x 480 @ 60Hz  
640 x 480 @ 67Hz  
640 x 480 @ 72Hz  
640 x 480 @ 75Hz  
800 x 600 @ 56Hz  
800 x 600 @ 60Hz  
800 x 600 @ 72Hz  
800 x 600 @ 75Hz  
832 x 624 @ 75Hz  
1024 x 768 @ 60Hz  
1024 x 768 @ 70Hz  
1024 x 768 @ 75Hz  
1280 x 1024 @ 75Hz  
1152 x 870 @ 75Hz  
1280 x 720 @ 60Hz  
1280 x 800 @ 60Hz  
1280 x 1024 @ 60Hz  
1600x1200@60Hz  
640 x 480P @ 60Hz 4:3  
720 x 480i @ 60Hz 16:9  
720 x 480p @ 60Hz 4:3  
720 x 480p @ 60Hz 16:9  
720 x 576i @ 50Hz 16:9  
720 x 576p @ 50Hz 4:3  
720 x 576p @ 50Hz 16:9  
1280 x 720p @ 60Hz 16:9  
1280 x 720p @ 50Hz 16:9  
1920 x 1080i @ 60Hz 16:9  
1920 x 1080i @ 50Hz 16:9  
1920 x 1080p @ 60Hz 16:9  
1920 x 1080p @ 50Hz 16:9  
1920 x 1080p @ 24Hz 16:9  
3840 x 2160 @ 24Hz  
1920 x 1080p @ 60Hz  
1366x768@60Hz  
1280 x 800@60Hz  
1080p:  
1920 x 1080p @120Hz  
1920 x 1200@60Hz- RB  
1920 x 1080@60Hz  
XGA:  
640 x 480@120Hz  
800 x 600@120Hz  
1024 x 768@120Hz  
1280 x 800@120Hz  
1024 x 768@60Hz  
3840 x 2160 @ 25Hz  
3840 x 2160 @ 30Hz  
4096 x 2160 @ 24Hz  
Digital (HDMI 2.0)  
B0 / Detail Timing  
B0 / Established  
B0 / Standard Timing  
B1 / Video Mode  
B1 / Detail Timing  
Timing  
720 x 400 @ 70Hz  
640 x 480 @ 60Hz  
640 x 480 @ 67Hz  
640 x 480 @ 72Hz  
640 x 480 @ 75Hz  
800 x 600 @ 56Hz  
800 x 600 @ 60Hz  
800 x 600 @ 72Hz  
800 x 600 @ 75Hz  
832 x 624 @ 75Hz  
1024 x 768 @ 60Hz  
1024 x 768 @ 70Hz  
1024 x 768 @ 75Hz  
1280 x 1024 @ 75Hz  
1152 x 870@ 75Hz  
1280 x 720 @ 60Hz  
1280 x 800 @ 60Hz  
1280x1024 @ 60Hz  
1600x1200@60Hz  
WXGA:  
640 x 480P @ 60Hz 4:3  
720 x 480p @ 60Hz 16:9  
720 x 576p @ 50Hz 4:3  
720 x 576p @ 50Hz 16:9  
1280 x 720p @ 60Hz 16:9  
1280 x 720p @ 50Hz 16:9  
1920 x 1080i @ 60Hz 16:9  
1920 x 1080i @ 50Hz 16:9  
1920 x 1080p @ 60Hz 16:9  
1920 x 1080p @ 50Hz 16:9  
1920 x 1080p @ 24Hz 16:9  
3840 x 2160 @ 24Hz 16:9  
3840 x 2160 @ 25Hz 16:9  
3840 x 2160 @ 30Hz 16:9  
4096 x 2160 @ 24Hz  
1920 x 1200@60Hz- RB  
1366x768@60Hz  
1280x800@60Hz  
1080p:  
1920x1080@120Hz  
1920x1080@60Hz  
XGA:  
640x480@120Hz  
800x600@120Hz  
1024x768@120Hz  
1280x800@120Hz  
1024 x 768@60Hz  
3840 x 2160 @ 50Hz  
3840 x 2160 @ 60Hz  
4096 x 2160 @ 50Hz  
4096 x 2160 @ 60Hz  
4096 x 2160 @ 25Hz  
4096 x 2160 @ 30Hz  
English  
54  
 
ADDITIONAL INFORMATION  
 otee Functions vary depending on model definition.  
Analog compatibility  
B0 / Established  
B0 / Standard Timing  
B0 / Detail Timing  
WXGA:  
B1 / Video Mode  
B1 / Detail Timing  
Timing  
720 x 400 @ 70Hz  
640 x 480 @ 60Hz  
1280 x 720 @ 60Hz  
1280 x 800 @ 60Hz  
1280x800@120Hz(RB)  
1280x800@60Hz  
1900x1200 @  
60Hz(RB)  
640 x 480 @ 67Hz  
640 x 480 @ 72Hz  
640 x 480 @ 75Hz  
800 x 600 @ 56Hz  
800 x 600 @ 60Hz  
800 x 600 @ 72Hz  
800 x 600 @ 75Hz  
832 x 624 @ 75Hz  
1024 x 768 @ 60Hz  
1024 x 768 @ 70Hz  
1024 x 768 @ 75Hz  
1280 x 1024 @ 75Hz  
1152 x 870 @ 75Hz  
1280 x 1024 @ 60Hz  
1600 x 1200 @ 60Hz  
1280 x 960 @ 60Hz  
640 x 480 @ 120Hz  
800 x 600 @ 120Hz  
1024 x 768 @ 120Hz  
1080p:  
1366x768@60Hz  
1920x1080@60Hz  
XGA:  
1024 x 768@60Hz  
 otee Functions vary depending on model definition.  
MHL compatibility  
Modes  
MHL Digital  
Resolution  
V. Frequency [Hz]  
H. Frequency [Hz]  
VGA  
480i  
640x480  
1440x480  
1440x576  
720x480  
720x576  
1280x720  
59.94/60  
59.94/60  
50.0  
31.5  
15.7  
15.7  
15.6  
15.6  
31.5  
31.5  
31.3  
31.3  
45.0  
37.5  
33.8  
28.1  
27.0  
576i  
480p  
576p  
720p  
720p  
1080i  
1080i  
1080p  
1080p  
1080p  
1080p  
1080p  
59.94/60  
50.0  
59.94/60  
50.0  
1280x720  
1920x1080  
1920x1080  
60.0  
50.0  
1920x1080  
23.97/24  
25.0  
1920x1080  
1920x1080  
29.97/30  
50.0  
1920x1080  
1920x1080  
60.0  
Horizontal scan rate:  
15k-68kHz  
Graphic source  
monitor range limits  
Vertical scan rate:  
Max. pixel rate:  
24-60Hz  
Digital: 148.5MHz  
55  
English  
ADDITIONAL INFORMATION  
True 3D video compatibility  
Input timing  
1280 x 720P @ 50Hz  
1280 x 720P @ 60Hz  
Top-and-Bottom  
Top-and-Bottom  
Frame packing  
Frame packing  
Side-by-Side(Half)  
Side-by-Side(Half)  
Top-and-Bottom  
Frame packing  
HDMI 3D Input  
(with 3D  
InfoFrame  
information)  
1280 x 720P @ 50Hz  
1280 x 720P @ 60Hz  
1920 x 1080i @ 50Hz  
1920 x 1080i @ 60Hz  
1920 x 1080P @ 24Hz  
1920 x 1080P @ 24Hz  
1920 x 1080i @ 50Hz  
1920 x 1080i @ 60Hz  
1280 x 720P @ 50Hz  
1280 x 720P @60Hz  
1920 x 1080i @ 50Hz  
1920 x 1080i @ 60Hz  
1280 x 720P @ 50Hz  
1280 x 720P @60Hz  
480i  
Input  
resolutions  
Side-by-Side(Half)  
SBS mode is on  
HDMI 3D Input  
(without 3D  
InfoFrame  
information)  
Top-and-Bottom  
HQFS  
TAB mode is on  
3D format is Frame sequential  
 otee  
If 3D input is 1080p@24Hz, the DMD should replay with integral multiple with 3D mode.  
1080i@25Hz and 720p@50Hz will run in 100Hz; 1080p@24Hz will run in 144Hz except WUXGA  
model is 96Hz; other 3D timing will run in 120Hz.  
Functions vary depending on model definition.  
56 English  
ADDITIONAL INFORMATION  
Image size and projection distance  
WXGA Series for 1.3x zoom  
To obtain an image size of 60” set the projector at a distance 1.5 m and 2.0 m from the screen.  
A
60”  
Desired image  
size  
D
Height: 91 cm  
from base to top of  
image  
1.5 m  
B
2.0 m  
C
Desired Distance  
Desired image size  
Distance (m)  
Top (cm)  
Diagonal (inch)  
W (cm) x H (cm)  
Max zoom  
Min zoom  
From base to top of image  
<A>  
30.07  
40  
<B>  
<C>  
<D>  
65 x 40  
86 x 54  
1.0  
1.3  
1.7  
2.0  
2.3  
2.7  
3.0  
3.3  
5.0  
6.0  
6.7  
45  
61  
1.0  
1.3  
1.5  
1.8  
2.0  
2.3  
2.6  
3.8  
4.6  
5.1  
6.4  
7.7  
50  
108 x 67  
129 x 81  
151 x 94  
172 x 108  
194 x 121  
215 x 135  
323 x 202  
388 x 242  
431 x 269  
538 x 337  
649 x 405  
76  
60  
91  
70  
106  
121  
136  
151  
227  
272  
303  
378  
456  
80  
90  
100  
150  
180  
200  
250  
301.2  
Zoom Ratio: 1.3x  
57  
English  
   
ADDITIONAL INFORMATION  
XGA Series for 1.3x zoom  
To obtain an image size of 60” set the projector at a distance 1.8 m and 2.4 m from the screen.  
A
60”  
Desired image  
size  
D
Height: 105 cm  
from base to top of  
image  
1.8 m  
B
2.4 m  
C
Desired Distance  
Desired image size  
Distance (m)  
Top (cm)  
Diagonal (inch)  
W (cm) x H (cm)  
Max zoom  
Min zoom  
From base to top of image  
<A>  
25.5  
30  
<B>  
<C>  
<D>  
52 x 39  
61 x 46  
1.0  
1.2  
1.6  
2.0  
2.4  
2.7  
3.1  
3.5  
3.9  
5.9  
7.1  
7.8  
45  
53  
40  
81 x 61  
1.2  
1.5  
1.8  
2.1  
2.4  
2.7  
3.0  
4.5  
5.4  
6.0  
7.6  
9.1  
70  
50  
102 x 76  
122 x 91  
142 x 107  
163 x 122  
183 x 137  
203 x 152  
305 x 229  
366 x 274  
406 x 305  
508 x 381  
612 x 459  
88  
60  
105  
123  
140  
158  
175  
263  
315  
351  
438  
528  
70  
80  
90  
100  
150  
180  
200  
250  
301.2  
Zoom Ratio: 1.3x  
58 English  
ADDITIONAL INFORMATION  
WXGA Series for fixed zoom  
To obtain an image size of 60” set the projector at a distance 0.67 m from the screen.  
A
60”  
Desired image  
size  
C
Height: 91 cm  
from base to top of  
image  
0.67 m  
B
Desired Distance  
Desired image size  
Distance (m)  
Top (cm)  
Diagonal (inch)  
W (cm) x H (cm)  
Max zoom  
From base to top of image  
<A>  
35.64  
40  
<B>  
<C>  
77 x 48  
86 x 54  
0.40  
0.45  
0.56  
0.67  
0.79  
0.90  
0.979  
1.01  
1.12  
1.35  
1.68  
2.02  
2.81  
3.37  
54  
61  
50  
108 x 67  
129 x 81  
151 x 94  
172 x 108  
188 x 117  
194 x 121  
215 x 135  
258 x 162  
323 x 202  
388 x 242  
538 x 337  
646 x 404  
76  
60  
91  
70  
106  
121  
132  
136  
151  
182  
227  
272  
378  
454  
80  
87.2  
90  
100  
120  
150  
180  
250  
300  
Zoom Ratio: 1.0x  
59  
English  
ADDITIONAL INFORMATION  
XGA Series for fixed zoom  
To obtain an image size of 60” set the projector at a distance 0.75 m from the screen.  
A
60”  
Desired image  
size  
C
Height: 105 cm  
from base to top of  
image  
0.75 m  
B
Desired Distance  
Desired image size  
Distance (m)  
Top (cm)  
Diagonal (inch)  
W (cm) x H (cm)  
Max zoom  
From base to top of image  
<A>  
31.9  
40  
<B>  
<C>  
65 x 49  
81 x 61  
0.40  
0.50  
0.63  
0.75  
0.88  
1.00  
1.13  
1.25  
1.50  
1.88  
2.26  
3.13  
3.76  
56  
70  
50  
102 x 76  
122 x 91  
142 x 107  
163 x 122  
183 x 137  
203 x 152  
244 x 183  
305 x 229  
366 x 274  
508 x 381  
610 x 457  
88  
60  
105  
123  
140  
158  
175  
210  
263  
315  
438  
526  
70  
80  
90  
100  
120  
150  
180  
250  
300  
Zoom Ratio: 1.0x  
60 English  
ADDITIONAL INFORMATION  
1080p series  
To obtain an image size of 60” set the projector at a distance 1.6 m and 2.1 m from the screen.  
A
60”  
Desired image  
size  
D
Height: 86 cm  
from base to top of  
image  
1.6 m  
B
2.1 m  
C
Desired Distance  
Desired image size  
Distance (m)  
Top (cm)  
Diagonal (inch)  
W (cm) x H (cm)  
Max zoom  
Min zoom  
From base to top of image  
<A>  
<B>  
<C>  
<D>  
28  
62 x 35  
84 x 47  
1.0  
1.3  
1.4  
1.8  
2.1  
2.5  
2.8  
3.2  
3.5  
4.2  
5.3  
6.3  
7.0  
40  
54  
38  
1.0  
1.1  
1.3  
1.6  
1.9  
2.1  
2.4  
2.7  
3.2  
4.0  
4.8  
5.4  
6.7  
8.0  
40  
89 x 50  
57  
50  
111 x 62  
72  
60  
133 x 75  
155 x 87  
177 x 100  
199 x 112  
221 x 125  
266 x 149  
332 x 187  
398 x 224  
443 x 249  
553 x 311  
665 x 374  
86  
70  
100  
115  
129  
143  
172  
215  
258  
286  
358  
430  
80  
90  
100  
120  
150  
180  
200  
250  
300.3  
Zoom Ratio: 1.31x  
61  
English  
ADDITIONAL INFORMATION  
The projector is equipped with lens shift for adjusting the position of projected image up and down without requiring  
you to physically move the projector.  
 otee The figures shown in this section are for reference only not approximate value. The figures between units  
can be different due to assembly tolerance.  
The vertical height can be adjusted between 5% and 15% of the image height. (The typical vertical image offset is  
fixed at 15% of the image height above the center of the projector lens.)  
H
Offset max=V x [A]  
Offset min=V x [B]  
max [A]  
min [B]  
Offset  
15%  
5%  
V
62 English  
ADDITIONAL INFORMATION  
Projector dimensions and ceiling mount installation  
1.  
2.  
To prevent damage to your projector, please use the Acer ceiling mount.  
If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to  
the projector meet the following specifications:  
Screw type: M4*9  
Minimum screw length: 9mm  
Lens  
Unit: mm  
 otee Please note that damage resulting from incorrect installation will void the warranty.  
Warning:  
If you buy a ceiling mount from another company, please be sure to use the correct screw size.  
Screw size will vary depending on the thickness of the mounting plate.  
Be sure to keep at least 10 cm gap between the ceiling and the bottom of the projector.  
Avoid installing the projector near a heat source.  
63  
English  
 
ADDITIONAL INFORMATION  
Troubleshooting  
If you experience a problem with your projector, please refer to the following information. If a problem persists,  
please contact your local reseller or service center.  
Image problems  
No image appears on-screen  
Ensure all the cables and power connections are correctly and securely connected as described in the  
"Installation" section.  
Ensure the pins of connectors are not crooked or broken.  
Ensure that the "Mute" feature is not turned on.  
Image is out of focus  
Turn the focus ring clockwise or counterclockwise until the image is sharp and legible. (Please see  
page 20).  
Make sure the projection screen is between the required distance from the projector. (Please refer to  
pages 57-57).  
The image is stretched when displaying 16:9 DVD title  
When you play anamorphic DVD or 16:9 DVD, the projector will show the best image in 16: 9 format  
on projector side.  
If you play the LBX format DVD title, please change the format as LBX in projector OSD.  
If you play 4:3 format DVD title, please change the format as 4:3 in projector OSD.  
Please setup the display format as 16:9 (wide) aspect ratio type on your DVD player.  
Image is too small or too large  
Turn the zoom lever clockwise or counterclockwise to increase or decrease the projected image size.  
(Please see page 20).  
Move the projector closer to or further from the screen.  
Press "Menu" on the projector panel, go to "Display → Aspect Ratio". Try the different settings.  
Image has slanted sides:  
If possible, reposition the projector so that it is centered on the screen and below the bottom of the  
screen.  
Image is reversed  
Select "Setup → Projection" from the OSD and adjust the projection direction.  
64 English  
 
ADDITIONAL INFORMATION  
Other problems  
The projector stops responding to all controls  
If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before  
reconnecting power.  
Remote control problems  
If the remote control does not work  
Check the operating angle of the remote control is pointed within ±20° to the IR receiver on the  
projector.  
Make sure there are not any obstructions between the remote control and the projector. Move to within  
5 m (16.4 ft) of the projector.  
Make sure batteries are inserted correctly.  
Replace batteries if they are exhausted.  
Warning indicators  
When the warning indicators (see below) light up or flash, the projector will automatically shutdown:  
“Lamp” LED indicator is lit red and if “Power” indicator flashes red.  
Temp” LED indicator is lit red and if “Power” indicator flashes red. This indicates the projector has  
overheated. Under normal conditions, the project can be switched back on.  
Temp” LED indicator flashes red and if “Power” indicator flashes red.  
Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up or  
flash, please contact your nearest service center for assistance.  
65  
English  
 
ADDITIONAL INFORMATION  
LED lightning messages  
Power LED  
Temp LED  
Lamp LED  
Message  
(Red)  
(Blue)  
(Red)  
(Red)  
Standby state  
(Input power cord)  
Steady light  
Flashing  
(0.5 sec off / 0.5 sec  
on)  
Power on (Warming)  
Power on and Lamp lighting  
Steady light  
Flashing  
(0.5 sec off / 0.5  
sec on). Back to red  
steady light when  
cooling fan turns off.  
Power off (Cooling)  
Error (Lamp failure)  
Error (Fan failure)  
Error (Over temp.)  
Flashing  
Flashing  
Flashing  
Steady light  
Flashing  
Steady light  
Power off:  
Power Off  
Power Off?  
Press power key again.  
Temperature warning:  
Warning  
TEMPERATURE TOO HIGH  
Please:  
1. Make sure air in and outlets are not blocked.  
2. Make sure the environment temperature is under 45 degree C.  
If the problem persists in spite of the above.  
Please contact a service center for repair.  
66 English  
ADDITIONAL INFORMATION  
Specifications  
Optical  
Description  
Maximum resolution  
Native resolution  
Lens  
1920x1200@60Hz(RB)  
XGA 1024(H) x 768(V)  
WXGA 1280(H) x 800(V)  
1080p 1920(H) x 1080(V)  
Manual zoom and manual focus  
XGA: 25.5” ~ 301.2” (65cm ~ 765cm)  
WXGA: 30” ~ 300” (76cm ~ 762cm)  
1080p: 28” ~ 300” (72cm ~ 762cm)  
Image size (diagonal)  
XGA (Fixed zoom): 32” ~ 300” (81cm ~ 762cm)  
WXGA (Fixed zoom): 36” ~ 300” (91cm ~ 762cm)  
XGA: 1m ~ 9.1m (3.3”~29.7”)  
WXGA: 1m ~ 7.7m (3.3”~25.2”)  
Projection distance  
1080p: 1m ~ 8m (3.3”~26.4”)  
XGA (Fixed zoom): 0.4m ~ 3.8m (1.3”~12.3”)  
WXGA (Fixed zoom): 0.4m ~ 3.4m (1.3”~11”)  
Electrical  
Description  
HDMI 1.4a  
HDMI 2.0b / MHL 2.2  
VGA in  
Inputs  
Composite (RCA connector (Y))  
Audio In 3.5mm  
Micro-USB for FW update  
USB Type A for WiFi (For 1080p only)  
Audio Out 3.5mm  
Outputs  
USB Type-A for DC 5V Out  
RS232  
Control  
RJ-45 (support web control)(For Fixed zoom only)  
Color reproduction  
Scan rate  
1073.4 Million color  
Horizontal scan rate: 15.374~91.146 KHz  
Vertical scan rate: 50~ 85 Hz (120Hz for 3D feature projector)  
Built-in speaker  
Power requirement  
Input current  
10W  
100 - 240V ±10%, AC 50/60Hz  
3.0A  
Mechanical  
Installation orientation  
Dimensions  
Description  
Front, Rear, Ceiling-top, Rear-top  
337mm x 265mm x 119.3mm (with feet) (13.3” x 10.4” x 4.7”)  
1080p: 4.6kg (10.1 lbs)  
Weight  
XGA/WXGA: 4.2kg (9.3 lbs)  
Environmental conditions  
Operating in 5 ~ 40°C , 10% to 85% humidity (non-condensing)  
 otee All specifications are subject to change without notice.  
67  
English  
 
ADDITIONAL INFORMATION  
Regulations and safety notices  
FCC notice  
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15  
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a  
residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause  
harmful interference to radio or television reception, which can be determined by turning the device off and on, the  
user is encouraged to try to correct the interference by one or more of the following measures:  
y Reorient or relocate the receiving antenna.  
y Increase the separation between the device and receiver.  
y Connect the device into an outlet on a circuit different from that to which the receiver is connected.  
y Consult the dealer or an experienced radio/television technician for help.  
Notice: Shielded cables  
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC  
regulations.  
Notice: Peripheral devices  
Only peripherals (input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be  
attached to this equipment. Operation with non-certified peripherals is likely to result in interference to radio and TV  
reception.  
Caution  
Changes or modifications not expressly approved by the manufacturer could void the user’s authority, which is  
granted by the Federal Communications Commission, to operate this device.  
Operation conditions  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this  
device may not cause harmful interference, and (2) this device must accept any interference received, including  
interference that may cause undesired operation.  
 oticee Canadian users  
This Class B digital apparatus complies with Canadian ICES-003.  
Remarque à l’intention des utilisateurs canadiens  
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du Canada.  
Compliant with Russian/ Ukraine regulatory certification  
Radio device regulatory notice  
 otee The regulatory information below is for models with wireless LAN and/or Bluetooth only.  
68 English  
ADDITIONAL INFORMATION  
General  
This product complies with the radio frequency and safety standards of any country or region in which it has  
been approved for wireless use. Depending on configurations, this product may or may not contain wireless radio  
devices (such as wireless LAN and/or Bluetooth modules).  
Canada — Low-power license-exempt radio communication devices (RSS-  
247)  
a Common information  
Operation is subject to the following two conditions:  
1. This device may not cause interference, and  
2. This device must accept any interference, including interference that may cause undesired operation of the  
device.  
b Operation in 2.4 GHz band  
To prevent radio interference to the licensed service, this device is intended to be operated indoors and  
installation outdoors is subject to licensing.  
List of applicable countries  
This device must be used in strict accordance with the regulations and constraints in the country of use. For further  
information, please contact the local office in the country of use.  
Please see http://ec.europa.eu/enterprise/rtte/implem.htm for the latest country list.  
69  
English  
Acer Incorporated  
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi  
New Taipei City 221, Taiwan  
EU Declaraon of Conformity  
We,  
Acer Incorporated  
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan  
And,  
Acer Italy s.r.l.  
Viale delle Industrie 1/A, 20020 Arese (MI), Italy  
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913  
Product:  
Acer Wireless Projection Kit  
Acer  
Trade Name:  
Marketing name: UWA5  
We, Acer Incorporated, hereby declare under our sole responsibility that the product described above  
is in conformity with the relevant Union harmonizaꢀon legislaꢀons: Direcꢀve 2014/53/EU on Radio  
Equipment, RoHS Direcꢀve 2011/65/EU. The following harmonized standards and/or other relevant  
standards have been applied:  
Electromagneꢀc compaꢀbility  
EN 55032:2015+AC:2016, Class B  
EN 61000-3-2:2014 Class D  
EN 61000-3-3:2013  
EN 55035:2017  
EN301 489-1 V2.1.1  
EN301 489-3 V1.6.1  
EN 301 489-17 V3.1.1  
Radio frequency spectrum usage  
EN 300 328 V2.1.1  
EN 300 440 v2.2.1  
EN 301 893 V2.1.1  
Healthy and Safety  
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/A2:2013  
EN 62209-2:2010 EN 62479:2010  
RoHS  
EN 62321:2009  
EN 50566:2017  
Operaꢀon frequency and radio-frequency power are listed as below:  
Bluetooth: 2402-2480MHz < 10 dBm  
WLAN 2.4GHz: 2412MHz-2462MHz < 20dBm  
WLAN 5GHz: 5180-5320MHz < 23dBm  
WLAN 5GHz: 5500-5700MHz < 23dBm  
Year to begin affixing CE marking 2019.  
_______________________________  
RU Jan / Sr. Manager  
Acer Incorporated (Taipei, Taiwan)  
Aug. 28, 2019  
Date  
Acer Incorporated  
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi  
New Taipei City 221, Taiwan  
Declaraon of Conformity  
We,  
Acer Incorporated  
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan  
And,  
Acer Italy s.r.l.  
Viale delle Industrie 1/A, 20020 Arese (MI), Italy  
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913  
Product:  
Trade Name:  
Model Number:  
DLP Projector  
Acer  
DWU1902/DWX1904/DNX1905/D1P1906/DWX1907/DNX1908  
Marketing name: PL1620n/PL1325W/PL1320W/PL1220/SL1520i/SL1320Wn/SL1220n/  
FL162/FL221A/FL122/FL112/FL152S/FL122S/FL112S/  
LU-P200U/LU-P500WA/LU-P200W/LU-P200X/LU-S200F/LU-S200W/LU-S200X/  
PF-L200U/PF-L500WA/PF-L200W/PF-L200X/PS-L200F/PS-L200W/PS-L200X/  
LR630/LR335/LR330/LR230/LR530S/LR330S/LR230S/  
ML-530/ML-235/ML-230/ML-130/ML-430S/ML-230S/ML-130S  
We, Acer Incorporated, hereby declare under our sole responsibility that the product described above  
is in conformity with the relevant Union harmonizaꢀon legislaꢀons: Direcꢀve 2014/53/EU on Radio  
Equipment, RoHS Direcꢀve 2011/65/EU and ErP Direcꢀve 2009/125/EC. The following harmonized  
standards and/or other relevant standards have been applied:  
Electromagneꢀc compaꢀbility  
EN 55032:2015+AC:2016, Class B  
EN 61000-3-2:2014 Class D  
EN 61000-3-3:2013  
EN 55024: 2010+A1:2015  
EN 301 489-1 V2.1.1  
EN 301 489-3 V2.1.1  
EN 301 489-7 V1.3.1  
EN 301 489-17 V3.1.1  
EN 301 489-24 V1.5.1  
Radio frequency spectrum usage  
EN 300 328 V2.1.1  
EN 300 440-1 V1.6.1  
EN 300 440 V2.1.1  
EN 302 291-1 V1.1.1  
EN 302 291-2 V1.1.1  
EN 301 511 V9.0.2  
EN 301 893 V2.1.1  
EN 301 908-1 V7.1.1  
EN 301 908-2 V6.2.1  
EN 301 908-13 V6.2.1  
Healthy and Safety  
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/A2:2013  
EN 62209-1:2006  
EN 62209-2:2010  
EN 50360: 2001/A1: 2012  
EN 50566:2013  
EN 62311:2008  
EN 62479:2010  
RoHS  
EN 50581:2012  
ErP  
Regulaꢀon (EU) No. 617/ 2013  
Regulaꢀon (EC) No. 278/2009; EN 50563:2011  
Regulaꢀon (EC) No. 1275/ 2008; EN 50564:2011  
Year to begin affixing CE marking 2019.  
_______________________________  
RU Jan / Sr. Manager  
Acer Incorporated (Taipei, Taiwan)  
Aug. 28, 2019  
Date  
71  
English  
Acer Incorporated  
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi  
New Taipei City 221, Taiwan  
Declaraon of Conformity  
We,  
Acer Incorporated  
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan  
And,  
Acer Italy s.r.l.  
Viale delle Industrie 1/A, 20020 Arese (MI), Italy  
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913  
Product:  
LED Projector  
Acer  
Trade Name:  
Model Number: D1P1903  
Marketing name: PL1520i/FL152/LU-P200F/PF-L200F/LR530/ML-430/VL6530i  
We, Acer Incorporated, hereby declare under our sole responsibility that the product described above  
is in conformity with the relevant Union harmonizaꢀon legislaꢀons: Direcꢀve 2014/53/EU on Radio  
Equipment, RoHS Direcꢀve 2011/65/EU and ErP Direcꢀve 2009/125/EC. The following harmonized  
standards and/or other relevant standards have been applied:  
Electromagneꢀc compaꢀbility  
EN 55032:2015+AC:2016, Class B  
EN 61000-3-2:2014 Class D  
EN 61000-3-3:2013  
EN 55024: 2010+A1:2015  
EN 301 489-1 V2.1.1  
EN 301 489-3 V2.1.1  
EN 301 489-7 V1.3.1  
EN 301 489-17 V3.1.1  
EN 301 489-24 V1.5.1  
Radio frequency spectrum usage  
EN 300 328 V2.1.1  
EN 300 440-1 V1.6.1  
EN 300 440 V2.1.1  
EN 302 291-1 V1.1.1  
EN 302 291-2 V1.1.1  
EN 301 511 V9.0.2  
EN 301 893 V2.1.1  
EN 301 908-1 V7.1.1  
EN 301 908-2 V6.2.1  
EN 301 908-13 V6.2.1  
Healthy and Safety  
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/A2:2013  
EN 62209-1:2006  
EN 62209-2:2010  
EN 50360: 2001/A1: 2012  
EN 50566:2013  
EN 62311:2008  
EN 62479:2010  
RoHS  
EN 50581:2012  
ErP  
Regulaꢀon (EU) No. 617/ 2013  
Regulaꢀon (EC) No. 1275/ 2008; EN 50564:2011  
This radio equipment operates with the following frequency bands and maximum radio-frequency power:  
Regulaꢀon (EC) No. 278/2009; EN 50563:2011  
GSM  
WLAN  
5GHz 2.4GHz  
<23dBm <20dBm  
Frequency bands  
UMTS  
N/A  
LTE  
Bluetooth  
<20dBm  
850/900 1800/1900  
Maximum radio-  
frequency power  
N/A  
N/A  
N/A  
Year to begin affixing CE marking 2019.  
_______________________________  
RU Jan / Sr. Manager  
Acer Incorporated (Taipei, Taiwan)  
Aug. 28, 2019  
Date  
English  
72  
Acer America Corporation  
333 West San Carlos St.,  
Suite 1500  
San Jose, CA 95110  
U. S. A.  
Tel: 254-298-4000  
Fax: 254-298-4147  
Federal Communications Commission  
Declaration of Conformity  
This device complies with Part 15 of the FCC Rules. Operation is subject to the  
following two conditions: (1) this device may not cause harmful interference,  
and (2) this device must accept any interference received, including interference  
that may cause undesired operation.  
The following local Manufacturer / Importer is responsible for this declaration:  
Product:  
DLP Projector  
Model Number:  
DWU1902/D1P1903/DWX1904/DNX1905/  
D1P1906/DWX1907/DNX1908  
Machine Type:  
PL1620n/PL1520i/PL1325W/PL1320W/PL1220/  
SL1520i/SL1320Wn/SL1220n/FL162/FL152/FL221A/  
FL122/FL112/FL152S/FL122S/FL112S/LU-P200U/  
LU-P200F/LU-P500WA/LU-P200W/LU-P200X/  
LU-S200F/LU-S200W/LU-S200X/PF-L200U/  
PF-L200F/PF-L500WA/PF-L200W/PF-L200X/  
PS-L200F/PS-L200W/PS-L200X/LR630/LR530/  
LR335/LR330/LR230/LR530S/LR330S/LR230S/  
ML-530/ML-430/ML-235/ML-230/ML-130/  
ML-430S/ML-230S/ML-130S/VL6530i  
Name of Responsible Party:  
Acer America Corporation  
Address of Responsible Party: 333 West San Carlos St.  
Suite 1500  
San Jose, CA 95110  
U. S. A.  
Contact Person:  
Phone No.:  
Fax No.:  
Acer Representative  
254-298-4000  
254-298-4147  
73  
English  

Tripp Lite Aps Powerverter User Manual
Sterling Sterlcool Cfp05 30w User Manual
Samsung Uq07sbge User Manual
Samsung Avmch052ea User Manual
Samsung Am20b1 B2 E06 User Manual
Malibu Lighting User Manual
KENWOOD PG 20 User Manual
GE AHH08 User Manual
BLACK DECKER KA2000 User Manual
ACER EXTENSA 4610 User Manual