White Rodgers Sst2000 User Manual

Electronic Air Cleaner  
Model Number  
SST  
S
R
GE  
D
O
E-R  
IT  
H
W
SST1000  
SST1400  
SST1600  
SST2000  
G
ATIN  
ER  
OP  
HT  
LIG  
ON  
F
OF  
OWNER’S MANUAL  
• Installation  
• Operation  
• Basic SST Service Guide  
• Technical Repair Guide  
• Repair Parts  
Please read and familiarize yourself with the contents of this manual before  
installing, operating or performing maintenance on the unit.  
White-Rodgers is a division  
of Emerson Electric Co.  
PART NO. 37-6373C  
Replaces 37-6373B  
0238  
Printed in U.S.A.  
A
B
C
HOW THE AIR CLEANER WORKS  
Dirt particles flowing through the ducts (Figure 1) first enters  
the pre-filters (A) where large particles (hair, lint, etc.) are  
trapped. Smaller particles (smoke, dust, pollen, etc.) pass  
through these pre-filters and enter the ionizing section (B).  
Here each tiny particle receives a positive electrical charge.  
These charged particles then enter the collecting section  
(C). This section consists of a series of aluminum plates  
which are alternately charged negative and positive.  
Dirty Air In  
Clean Air Out  
The positive charge of the particles cause them to be  
repelled by the positive plates and attracted to the negative  
plates where they are collected . . . just as a magnet  
attracts iron filings.  
Figure 1  
Clean-filtered air re-enters the supply duct system.  
Carbon (Charcoal) Filters  
White Dust (Lint)  
Odors are gas molecules, not particles. They cannot be  
removed by an Electronic Air Cleaner or by any other  
filtration media designed to remove airborne particles.  
However, some gases can be absorbed by an activated  
carbon filter or diluted with fresh outdoor air. When odors  
are present, the addition of charcoal filters will neutralize  
odors, such as cooking odors, pet odors, cigar and ciga-  
rette odors, ozone, etc. Optional charcoal filters are  
available for your Air Cleaner. Refer to the parts list for the  
charcoal filter part number for your Air Cleaner. Charcoal  
filters require replacement. They cannot be washed. While  
there is no rule of thumb for how often they should be  
changed, you can use your best judgement based on the  
odors you perceive in your environment.  
An Electronic Air Cleaner is designed to collect two major  
types of contaminants: LLIrritants (Pollens, Spores, Molds,  
Bacteria, etc.) and L Black Soiling Contaminants (Dirt and  
Smoke particles).  
The residue on the collecting plates of an electronic air  
cleaner is black, indicating it is removing dirt from the air  
stream. After installing an air cleaner you may notice white  
dust (typically, long linty particles or fibers – from carpets,  
cotton materials or drapery fabrics). This material is not  
collected by the air cleaner because it does not contain the  
irritants or soiling contaminants listed above or settles out of  
the air before reaching the air cleaner. The presence of  
white dust does not indicate an air cleaner requires service.  
CONSTRUCTION OF THE AIR CLEANER  
Not only is your air cleaner easy to install, it is also easy to  
operate and maintain. Its basic components, and their  
functions, are as follows: (See Figure 2)  
Pre-Filters  
Cabinet  
Handle  
Cabinet - mounts to existing duct work and houses the  
collecting cells and pre-filters.  
Collecting Cells - are made in two sections and perform  
the actual collecting of dust, dirt, and other impuri-  
ties from the air. They contain the ionizing and  
collection sections described above.  
Each cell must be installed with the ionizing wires  
on the air entering side. Each cell must be oriented  
with the handles and contact button (Figure 2)  
toward the operator.  
Contact  
Button  
Pre-filters - are in two sections which are interchangeable.  
They serve as a pre-filter to trap large particles  
such as hair and lint before they can enter the cell  
sections.  
Collecting Cells  
Contact  
Button  
Power Pack  
Figure 2  
Power Pack- contains operating and power on lights as well  
as the solid state components that convert the 120  
volt power supply to the high-voltage, direct current  
required for the collecting cell.  
3
PREINSTALLATION  
Not to Exceed 20  
(Interchangeable)  
Collecting Cell  
(Interchangeable)  
Collecting Cell  
Air Flow  
Outlet Box  
Cabinet  
Power Pack  
Handle  
Air Flow  
Furnace  
Opening  
Electronic  
Air Cleaner  
Opening  
Contact  
Button  
Contact  
Button  
Furnace  
Electronic  
Air Cleaner  
Pre-Filters  
(Interchangeable)  
Transition Section  
(if Needed)  
See text for Cell  
Removal Clearance  
Figure 4  
Figure 3  
LOCATING THE AIR FILTER  
Knockouts for  
3/4" Conduit  
(three sides)  
Your air filter must be mounted in the return air duct of a  
central forced-air system, on the air entering side of your  
furnace. (See Figure 3 for example.)  
6 7/8"  
Select a location that meets the following:  
1. The face of the cell will be at a right angle to the air  
stream.  
2. Allow the following clearances to permit removal of  
cells and pre-filters: (See Figures 4 and 5)  
C
F
E
Model SST1000 - 14 inches  
Model SST1400 - 15 inches  
Model SST1600 - 14 inches  
Model SST2000 - 15 inches  
D
For complete dimension data refer to Figure 5.  
3. The air filter is not to be placed in the discharge of  
either the heating or cooling unit.  
B
4. IMPORTANT: If atomizing spray type humidifier is  
used, it must be installed downstream from the air  
filter.  
A
If your furnace duct system has a pre-installed boot,  
discard front cover of boot and slide the air cleaner  
component inside the boot. For installation of Air Cleaner  
Retrofit (ACR) kits, see page 13.  
MODEL NO.  
A
B
C
D
E
F
SST1000  
SST1400  
SST1600  
SST2000  
24 3/4 21 5/16 18 5/8 13 9/16 16 7/16 19 1/16  
29 11/16 26 1/4 23 5/8 13 9/16 16 7/16 19 1/16  
25 1/2 21 5/16 18 5/8 17 3/4 20 5/8 23 3/8  
29 11/16 26 1/4 23 5/8 17 3/4 20 5/8 23 3/8  
If furnace opening cannot be enlarged to required size, a  
transition sheet metal section must be used. Transition  
must be planned for each job. Reduction should not be  
more than 4 inches per linear foot, approximately 20  
angular degrees (Figure 3).  
Figure 5  
tions. Turn cells upside down (with the same end facing  
the cabinet opening). This will locate the ionizing wires at  
the right, and both contact buttons and cell handles will be  
facing the power door. Air flow direction must agree with  
arrow embossed on end of collecting cells.  
DIRECTION OF AIR FLOW THROUGH THE  
AIR CLEANER  
After installing the cell sections, install pre-filters in cabi-  
net tracks on the right. This will again place the pre-filters  
on the air entering side (on the same side as ionizing  
wires).  
Your air cleaner is shipped from the factory with air flow  
from left-to-right. If this air flow is suitable for the installa-  
tion, no further changes need to be made (Figure 4). For  
right-to-left air flow, remove both pre-filter and cell sec-  
4
TYPICALMOUNTINGPOSITIONS  
Air Flow  
Air Flow  
Air Flow  
Rear View  
Rear View  
Figure 6  
BASEMENT FURNACE  
Figure 8  
Figure 7  
HIGHBOY FURNACE  
(Figure 8)  
(LOWBOY) (Figure 6)  
COUNTERFLOW  
FURNACE (Figure 7)  
Cleaner is mounted hori-  
zontally in return plenum,  
just above furnace.  
Side installation. Cleaner  
is mounted vertically,  
where return air enters  
side inlet of furnace.  
Cleaner is mounted horizon-  
tally in return duct or plenum,  
just above furnace.  
HIGHBOY FURNACE  
(Figure 9)  
Installation beneath furnace.  
Cleaner mounts horizontally,  
where return air enters from  
below. Raise furnace and in-  
stall beneath base.  
Less than  
7 Inches  
Offset  
At Least  
9 Inches  
Air Flow  
Figure 10  
OFFSET INSTALLATION  
(Figure 10)  
Figure 9  
Typical use of duct offset to match air filter opening.  
If duct connection to furnace allows less than nine  
inches for mounting the air cleaner, shorten the  
lateral trunk, or attach an offset fitting to the elbow.  
Air Flow  
HORIZONTAL FURNACE  
(Figure 11)  
Cleaner is mounted vertically  
in the return duct near furnace.  
Figure 11  
5
INSTALLATION  
REMOVE OLD FILTER AND DISCARD  
(Figure 12)  
NOTE:Thisfiltermaybemountedinthefurnacecompart-  
ment.  
CLEAN BLOWER COMPARTMENT  
It is suggested that the furnace blower compartment,  
blower and blower housing be cleaned to ensure clean air  
circulation.  
Figure 12  
Power  
Supply  
Box  
INSTALLATION  
Frame  
The following is a typical installation of the air cleaner on  
a “Highboy” furnace (Figure 8).  
Duct  
1. Place the air filter cleaner on the floor. Stand it upright  
with the power door facing you (Figure 4). If a  
horizontalinstallationisbeingplanned,laythecleaner  
on its side, this will help you to visualize the relative  
location of all parts.  
Allow ample space for wiring and servicing the power  
supply box (Figure 13).  
Mounting  
Holes  
2. Release the latch, remove the power pack (by grasp-  
inghandleandpullingpowerpackawayfromcabinet)  
and set it aside. Remove the collecting cells and pre-  
filters. Set pre-filters and cells aside in a safe location  
until the cabinet is installed.  
Figure 13  
3. Set the cabinet next to the furnace. If necessary,  
enlarge the opening in the furnace (if possible) to  
match the opening in the cabinet.  
Turning  
Vanes  
Air Flow  
If the furnace opening cannot be enlarged, a transi-  
tion fitting should be used. (Figure 3).  
The cabinet can be attached directly (Figure 13), or  
a starting collar can first be fitted to the furnace inlet.  
A butt or slip joint can be used.  
Securely attach the cabinet to furnace inlet, using at  
least two of the mounting holes on each side of the  
cabinet.  
Figure 14  
4. Using butt joint, attach duct work (normally an elbow)  
to the upstream side of air cleaner cabinet. (Note the  
use of the sheet metal turning vanes inside the elbow  
to improve air distribution over the face of the cells.)  
(Figure 14)  
NOTE: An optional method of attaching duct work to the  
cabinetistomodifythecabinet(Figure15)bybendingthe  
tabs outward at a 90° angle and attaching duct work to  
tabs.  
Optional method  
(Bend tabs outward at 90˚ angle)  
Figure 15  
5. Connecttheverticalductsectiontotheelbow.Wedge  
a wood block between floor and elbow for support  
(Figure 16).  
Transition Fittings  
If the air duct does not fit the cabinet opening, a transition  
fitting should be used. Gradual transitions are preferred  
for greatest efficiency. Not more than four inches per  
linear foot (approximately 20° angle) should be allowed  
(Figure 3).  
6. Seal all joints in the return air system downstream  
from the air cleaner with duct tape to prevent dust  
from entering the air stream. Tape is usually applied  
ontheoutsideofducts,butmayalsobeappliedonthe  
inside, or both.  
6
WIRINGINSTRUCTIONS  
10. With the cabinet Installed, reinstall pre-filter(s) and  
7. With the cabinet installed, the air cleaner can now be  
wired to electrical input source.  
collecting cell(s) (Figure 19).  
NOTE: The contact button and handles on the cell  
must be facing you and ionizing wires must be on the  
air intake side.  
!
WARNING  
Installation of this unit must comply with local  
electric codes or other applicable codes.  
11. Install the power pack as follows:  
Engage the lip on lower inside edge of power pack in  
the flange on cabinet and carefully close the power  
pack,makingsurethattheelectricalconnectorprongs  
on the power pack enter the slots in the socket on  
cabinet. When the power pack is fully in place, en-  
gage the latch and snap it closed.  
Review and understand local codes prior to in-  
stallation.  
Failure to do so could result in serious personal  
injury or death.  
8. This air cleaner unit has no air flow monitor installed,  
it does require electrical wiring through the furnace  
controls. Connect wiring to the furnace control termi-  
nals. (EAC-H) for power, (EAC-N) for neutral, and  
connect metal frame of EAC to ground. If air flow  
monitorisrequiredforoperation,orderF859-0381Air  
Flow kit. Install kit and connect a 120 VAC 60 Hz input  
circuit. A 20 amp circuit is more than adequate.  
Floor  
9. Remove junction box cover and install the required  
bushing into the 3/4 in. Knock out. With the supply  
voltage turned off, route three (3) wires into junction  
box for connections. (See Fig. 17.)  
Conduit  
Insure all wires are clamped, wire connectors prop-  
erly installed and grommets used to prevent wire  
abrasion.  
Vertical  
Section  
Duct  
Tape All  
Joints  
Electronic  
Air Cleaner  
Figure 18  
Pre-Filters  
Wood Block  
Cabinet  
Handle  
Figure 16  
Hot  
Neutral  
Grounding  
Conductor  
Contact  
Button  
Collecting Cells  
Contact  
Button  
Front View  
Figure 17  
Power Pack  
Figure 19  
7
OPERATION  
1. With the 120 VAC power turned on at the circuit  
breaker for the furnace, push the air cleaner ON-OFF  
switch to the “ON” position (Figure 20).  
2. With the furnace blower running, the air cleaner will  
be operating. An arcing or “snapping” sound may be  
heard. This will occur occasionally, however the unit  
is operating properly.  
3. With the furnace blower running, the Operating Light  
should be ON. If the Operating Light is not ON this  
signifies that the cells need washing, or that trouble  
exists in the unit.  
Operating  
Light  
If, after washing the cells, the Operating Light stays off,  
the cell could be wet, improperly placed in the cabinet or  
may need servicing.  
On-Off  
Switch  
NOTE: An occasional flicker of the light accompanied by  
harmless sparking or snapping noise may occur. This is  
caused by trapping large particles of dirt. If arcing is  
continuous, the cells should be washed or checked for  
service problems see Basic SST Service Guide.  
Figure 20  
4. Remove the cell(s) and pre-filter(s) from cabinet.  
Using a solution of warm water and low sudsing  
detergent, soak cell(s) and pre-filter(s) for 20 to 30  
minutes.  
MAINTENANCE AND WASHING  
!
CAUTION  
NOTE: Ionizing wires may become coated causing  
loss of cleaning ability by the collecting cell. Using a  
damp cloth, wipe each ionizing wire, exercising care  
not to damage them.  
CABINET AND CELLS MAY CON-  
TAIN SHARP EDGES.  
Use care when servicing unit or  
handling cells.  
5. Remove the cell(s) and pre-filter(s) from solution and  
rinse thoroughly with clean water.  
Failure to do so could result in  
minor personal injury.  
6
Allow cell(s) and pre-filter(s) to drip dry for a mini-  
mum of 2 hours. Cell(s) and pre-filter(s) may be  
tipped at a slight angle to expedite the drip-dry  
process.  
For maximum efficiency your air cleaner cell(s) and pre-  
filter(s) should be inspected once a month and cleaned  
when necessary. Cleaning will usually be required every  
one to three months, depending upon the particular  
household circumstances. When cleaning is required the  
following procedure should be used:  
7. Reinstall the cell(s) and pre-filter(s) in the cabinet.  
8. Replace the power pack. Turn furnace fan on. After  
30 minutes push ON-OFF switch on the power pack  
to the “ON” position.  
A moderate amount of arcing or “snapping” may  
occur at this time, which will indicate that the cell(s)  
are still damp. If the noise is objectionable, push the  
ON-OFF switch to the “OFF” position and allow  
additional time for cell(s) and pre-filter(s) to dry. In  
some cases the Operating Light will remain OFF  
during this initial activation of the air cleaner, and this  
would indicate that the cell(s) are not completely dry.  
The Operating Light should remain ON while the  
furnace fan is running once the drying is complete.  
CLEANING THE CELLS  
1. Turn the air moving system “OFF.”  
2. Push the ON-OFF switch on the power pack to the  
“OFF” position (Figure 20). Wait 15 seconds and both  
the power pack and the collecting cell(s) will be  
automatically discharged.  
3. Release the latch on top of power pack and pull the  
power pack straight away from cabinet at the top.  
Then lift pack out of ledge at bottom edge of cabinet.  
Set power pack aside.  
8
REPLACING AN IONIZING WIRE  
If an ionizing wire should break, it can be replaced as  
follows:  
1. Remove all pieces of broken wire. Make sure sup-  
ports at each end are in good condition and not bent  
out of shape.  
2. Hook the new wire onto the support at one end.  
3. Hold your finger against the support at the other end  
(Figure 21) and hold the ionizing wire between thumb  
and forefinger as shown or use needle nose pliers.  
Press inward on spring support. Hook end of wire  
over small tab at end of support and release. Make  
sure wire is securely anchored at each end.  
Support  
Ionizing  
Wire  
Figure 21  
SPECIFICATIONS  
SPECIFICATIONS  
SST1000  
SST1400  
SST1600  
SST2000  
Rated Capacity  
Max. Pressure Drop  
Cell Weight  
600 - 1200 cfm  
.08 in. W.G.  
(2) 7 lbs. each  
9 lbs.  
1000 - 1600 cfm  
.08 in. W.G.  
(2) 9 lbs. each  
9 lbs.  
1000 - 2000 cfm  
.12 in. W.G.  
(2) 9 lbs. each  
10 lbs.  
1600 - 2200 cfm  
.09 in. W.G.  
(2) 9 lbs. each  
10 lbs.  
Power Pack Weight  
Unit Weight  
35 lbs.  
42 lbs.  
38 lbs.  
45 lbs.  
Power Consumption  
Electrical Input  
40 Watts (Max)  
120 VAC 60 hz.  
1.0 Ma  
40 Watts (Max)  
120 VAC 60 hz.  
1.2 Ma  
40 Watts (Max)  
120 VAC 60 hz.  
1.5 Ma  
40 Watts (Max)  
120 VAC 60 hz.  
1.7 Ma  
Electrical Output  
@ 6450 VDC (nom)  
Max. Ozone Output  
Temperature Rating  
.05 ppm  
.05 ppm  
.05 ppm  
.05 ppm  
40 F to 125 F  
40 F to 125 F  
40 F to 125 F  
40 F to 125 F  
9
BASIC SST SERVICE GUIDE  
This guide will cover most homeowner complaints. If, after checking the items listed, the unit still fails to operate  
properly, contact the nearest Authorized Service Center.  
SERVICE INDICATION  
SERVICE CHECKS  
ON/OFF switch “ON”  
Blower ON  
Unit functioning Normally  
Operating Light ON  
ON/OFF switch “ON”  
Blower ON  
1. Power is not being supplied to air cleaner.  
A. Check fuse or circuit breaker.  
Operating Light OFF  
B. Ensure power pack is properly installed and latched.  
2. Collecting cell shorted - Turn power Off - Remove power pack - Remove  
collecting cells - Replace power pack - Restore power (ensure blower is  
operating).  
A. If Operating Light comes ON check cells for bent plates, loose ionizing  
wire(s) or cracked insulator(s).  
B. If Operating Light remains OFF, malfunction is in the power pack. (See  
power supply Checkout Procedure).  
ON/OFF Switch “ON”  
Blower OFF  
Operating Light ON  
1. Air flow sensor contaminated/misaligned  
A. Remove power pack and clear contamination inside black bushing around  
the small sensor element.  
B. Ensure small sensor element is centered in bushing.  
2. Air sensor left in bypassed condition after servicing.**  
3. Faulty air flow sensor panel.  
Excessive arcing during  
normal operation -  
Operating Light may blink  
1. Wet collecting cell.  
A. Allow cell(s) to dry after cleaning before applying power.  
2. Damaged collecting cell(s).  
A. Remove cell(s) and inspect for bent plates, loose ionizing wire(s), cracked  
insulator(s), etc.  
3. Collecting cells dirty.  
A. Clean cells as instructed in this manual.  
4. Faulty power supply (see power supply checkout procedure)  
**NOTE: Your air cleaner is equipped with an air flow sensor (switch) which turns the unit ON and OFF in  
response to the system blower. It may have been “wired out” during a service check and inadvertently left in this  
condition  
10  
TECHNICAL REPAIR GUIDE  
All voltage measurements indicated can be made with a  
high voltage D.C. probe and a general purpose volt ohm  
meter. For example: Simpson 260 or equivalent.  
!
WARNING  
Do not attempt repair of this unit unless you are  
familiar with the necessary tools, equipment,  
utility connections and potential hazards.  
For test purposes, the air flow switch may be “wired out”  
of the system. This will eliminate the need for air flow  
across the sensing thermistor to energize the power  
supply (see Fig 23).  
Repair should be performed only by a qualified  
service provider.  
NOTE: All tests to be performed with the Ozone Reduc-  
tion Jumper intact.  
Failure to do so could result in reduced perfor-  
mance of the unit, serious personal injury or  
death.  
NOTE: When servicing the power pack components, all  
wiring must be routed to factory specifications.  
This guide contains service checks to assist service  
personnel in locating and correcting any malfunction that  
might occur to render the air cleaner ineffective or inop-  
erative. The air cleaner has been designed with replace-  
able components, such as the high-voltage power supply  
and air flow switch. This allows the serviceman to replace  
a faulty component rather than attempt repairs of such  
components in the field.  
120 VAC  
Connector  
Power Pack  
Assembly  
L2  
L1  
Cover Assembly  
Power Supply  
Specifications  
The solid-state power supply is not  
designed for individual component part  
replacement and must be replaced as  
a complete "snap-in" unit.  
Operating  
Light  
(If Required)  
Airflow Switch  
ON/OFF  
Switch  
Blk  
Input voltage: 120 VAC 60 Hz.  
Output to light: 1.5 to 2.5 VDC  
H.V. Output: 6450 VDC (nom)  
Wht/Brn  
Wht  
Blk  
Red  
Gnd  
Collecting Cell  
Specifications  
Cell Contact  
& Insulator  
1000 cfm - 1.0 Ma @ 6450VDC  
1400 cfm - 1.2 Ma @ 6450 VDC  
1600 cfm - 1.5 Ma @ 6450 VDC  
2000 cfm - 1.7 Ma @ 6450 VDC  
Wht  
Blu  
Power  
Supply  
Wht/Brn/Air Flow  
Blk  
Figure 22  
11  
4. Using a standard extension cord, apply 120 VAC to  
power pack. Turn power switch to “ON” position.  
POWERSUPPLY  
CHECKOUTPROCEDURE  
5. Connect meter negative (-) lead to metal frame of  
collecting cell. Use high voltage probe to measure  
voltage at collecting cell ionizer or cell plates. Voltage  
should be 6100 to 6800 VDC.  
1. Turn power switch to the “OFF” position and remove  
the power pack from cabinet.  
2. If air flow switch is installed, locate air flow switch and  
remove power pack cover. If air flow switch is not  
installed, go to step 4.  
NOTE:Anewout-of-boxcellmaycausethevoltage  
to be lower than normal for a short period of time. To  
obtain a more accurate measurement, “age” the cell  
by applying high voltage to the cell for 15 to 30  
minutes.  
3. Disconnectthethree-pinplasticconnectorandjumper  
the two female pins (white wire to white-brown wire)  
as shown in Fig. 23.  
6
If voltage is below 6100 VDC, check cell for foreign  
objects, bowed/bent/loose plates, broken ionizing  
wires or cracked insulators. Wash cells if required. If  
Operating Light remains OFF, replace collecting cell.  
Plastic Connector  
Male Pin  
AIR FLOW MONITOR TEST  
Jumper Lead  
Female Pins  
1. Connect a multimeter set to read 120 VAC to power  
supply terminals marked “LINE.”  
Method of jumping lead wires of  
connector plug from air flow switch.  
2. Connect 120 VAC to power pack plug, turn power  
switch “ON.”  
Figure 23  
3. Blow on thermistor at air flow monitor. 120 VAC  
should appear at multimeter. Stop blowing and volt-  
age should disappear in 10 - 15 seconds.  
4. Place power pack on a well insulated workbench.  
Connect meter negative (-) lead to the sheet metal  
chassis and the high voltage probe to high voltage  
contact on back cover of power pack. Connect AC  
powertopowerpackusinganextensioncordandturn  
power switch to the “ON” position. Keep hands and  
tools away from high voltage contact.  
4. If voltage did not appear (Step 3), disconnect power  
to power pack. Locate air flow switch and remove  
power pack cover. Disconnect the three-pin plastic  
connector. Jumper the two female pins (white wire to  
white-brown wire) as shown in Fig. 23. Reconnect  
power to power pack. Turn power switch “ON.”  
5. If Operating Light comes ON and output voltage is  
between 6100 and 6800 VDC, power supply is good.  
A. If 120 VAC appears at multimeter, replace air  
flow monitor.  
6. If voltage is good but Operating Light does not come  
on, replace Operating Light.  
B. If 120 VAC does not appear on multimeter,  
problem is other than air flow monitor. Recheck  
all primary wiring.  
CELL TEST  
NOTE: The air flow monitor is designed to operate in the  
temperature range of 65° to 120° F. Operation outside  
this range is not recommended.  
1. Place collecting cell on a well insulated workbench  
with the cell contact button pointing upward.  
2. Select a power pack (with air flow switch bypassed  
and ozone reduction jumper intact) that reads be-  
tween 6100 and 6800 VDC at the cell contact with no  
cell attached.  
3. Place power pack on top of collecting cell ensuring  
that there is proper contact between the cell contact  
on the power pack contact.  
12  
OZONEREDUCTION  
All electronic air cleaners typically produce a small  
amount of ozone that is within established limits.  
Some customers may notice an odor especially at  
high altitudes or low air flow rates.  
W1  
This power supply has a “hairpin” shaped jumper  
wire labeled W1 (see Fig 24) that can be cut and  
separated in case of such complaints. This will  
cause the power supply to limit the maximum  
operating power to a lower level.  
Cut and separate  
Ozone Reduction  
Jumper  
WHT/BRN  
E3  
BLK  
E2  
LINE  
Ozone Reduction Jumper  
Figure 24  
ELECTRONIC AIR CLEANER RETROFIT (ACR) KITS  
INSTALLATION  
Pre-Filters  
Cabinet  
Handle  
1. Removethetwopre-filtersfromthepackageandinsert  
intocabinettracksoppositethefurnace. Thesewillbe  
used to catch the larger particles that are in the air  
stream before entering the collecting cell.  
2. Insert the two collecting cells into the cabinet behind  
the pre-filters. Be sure ionizing wires are directly  
behind the pre-filters so the particles can be charged  
as soon as the air leaves the pre-filters.  
3. Removecoverplateonthepowersupplyjunctionbox  
and remove the knockout needed to bring the wire to  
Contact  
Button  
the female receptacle.  
4. Positionreceptaclewithgroundinthedownpositionas  
Collecting Cells  
Contact  
Button  
shown in Fig 17 (page 7) and pull wires through the  
receptacle locator on the junction box. Snap the  
receptacle into the hole until secure.  
5. Connectgroundwirefromreceptacleandgroundwire  
in kit to cabinet with rivet and washer as follows:  
a) Place washer on rivet  
b) Place terminal from ground wire on rivet  
c) Place terminal from receptacle ground wire on  
rivet  
d) Insert rivet in hole in junction box and secure.  
WIRING  
5. Forwiringinstallation(seepage7)andfollowallwiring  
instructions 7, 8 and 9.  
6. Install the power pack (see page 7) instruction 11.  
7. For operation (see page 8 – Operation).  
13  
REPAIR PARTS  
5
4
6
1
5
2
3
7
2
3
9
8
13  
10  
18  
11  
12  
5
14  
14  
REPAIR PARTS  
PARTS LIST FOR ELECTRONIC AIR CLEANERS  
When ordering repair parts, always give the following information as  
shown in this list.  
1. The PART NUMBER  
2. The PART DESCRIPTION  
3. The MODEL NUMBER  
4. The NAME OF ITEM - Electronic Air Cleaner.  
Always order by “PART NUMBER” . . . Not by “ITEM NUMBER”  
PART NUMBER  
ITEM  
NO.  
DESCRIPTION  
SST1000  
SST1400  
SST1600  
SST2000  
1
Cabinet  
N/A  
N/A  
N/A  
N/A  
2
Pre-Filter  
F825-0431  
F811-0398  
F838-0072  
------  
F825-0432  
F811-0397  
F838-0072  
------  
F825-0337  
F811-0321  
F838-0072  
------  
F825-0338  
F811-0319  
F838-0072  
------  
3
Collecting Cell  
4
Junction Box Cover  
* Screw #6 x 3/8  
Connector, Female  
Power Pack Assembly  
Cell Handle  
5
6
F818-0053  
F858-1021  
F832-0039  
F843-0484  
F844-0130  
F876-0202  
N/A  
F818-0053  
F858-1022  
F832-0039  
F843-0484  
F844-0130  
F876-0202  
N/A  
F818-0053  
F858-1023  
F832-0039  
F843-0500  
F844-0130  
F876-0202  
N/A  
F818-0053  
F858-1024  
F832-0039  
F843-0500  
F844-0130  
F876-0202  
N/A  
7
8
9
Ionizing Wire  
10  
11  
12  
13  
14  
15  
16  
17  
18  
Light  
Switch  
Power Pack, Cabinet Only  
Connector, Male  
Power Supply  
F827-0026  
F858-1002  
F820-0098  
37-6373  
F827-0026  
F858-1002  
F820-0098  
37-6373  
F827-0026  
F858-1002  
F820-0220  
37-6373  
F827-0026  
F858-1002  
F820-0220  
37-6373  
Cover, Power Pack  
Manual  
Charcoal Filter (with mounting clips)  
Air Flow Switch (monitor kit)  
F825-0466  
F859-0381  
F825-0467  
F859-0381  
F825-0468  
F859-0381  
F825-0469  
F859-0381  
* Standard Hardware Item  
Two (2) Required  
Not Shown  
15  
WASH REMINDER SCHEDULE  
frequent washing may be necessary on some installa-  
A regular washing schedule is necessary to ensure tions where there is new carpeting, plaster dust or exces-  
proper efficiency. A thorough washing once every month sive cigarette smoke, etc. (See page 8 for maintenance  
will be adequate for most installations. More or Less  
and instructions on how to clean a cell.)  
Year  
JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC  
20___  
20___  
20___  
20___  
20___  
20___  
20___  
20___  
20___  
20___  
20___  
20___  
NOTICE TO CONSUMERS  
White-Rodgers  
Electronic Air Cleaner  
Dear Consumer;  
White-Rodgers would like to thank you for purchasing a White-Rodgers Electronic Air  
Cleaner or product containing a White-Rodgers Electronic Air Cleaner. Although White-  
Rodgers does not extend a warranty directly to consumers, White-Rodgers does extend a  
warranty to Wholesalers and Original Equipment Manufacturers who use White-Rodgers  
Products. To obtain more information about how your Wholesaler or Original Equipment  
Manufacturer’s warranty may benefit you, please contact your Wholesaler or Original  
Equipment Manufacturer.  
Sincerely,  
White-Rodgers  
TheEmersonlogois  
trademarkandaservicemark  
ofEmersonElectricCo.  

Mikasa Automobile Parts Mt 74f User Manual
Samsung Scx 5315f User Manual
Samsung Us18s0gb User Manual
Sanyo Rs1211 User Manual
Sanyo Thw4272r User Manual
Sanyo Twicell User Manual
Smc Networks Robo Cylinder Rcs2 User Manual
Soleus Air Kfmhp 18 Od User Manual
Stoptech Automobile Parts 98 180 1470 User Manual
Xerox Pe120i User Manual