Electronic Air Cleaner
Model Number
SST
S
R
GE
D
O
E-R
IT
H
W
SST1000
SST1400
SST1600
SST2000
G
ATIN
ER
OP
HT
LIG
ON
F
OF
OWNER’S MANUAL
• Installation
• Operation
• Basic SST Service Guide
• Technical Repair Guide
• Repair Parts
Please read and familiarize yourself with the contents of this manual before
installing, operating or performing maintenance on the unit.
White-Rodgers is a division
of Emerson Electric Co.
PART NO. 37-6373C
Replaces 37-6373B
0238
Printed in U.S.A.
A
B
C
HOW THE AIR CLEANER WORKS
Dirt particles flowing through the ducts (Figure 1) first enters
the pre-filters (A) where large particles (hair, lint, etc.) are
trapped. Smaller particles (smoke, dust, pollen, etc.) pass
through these pre-filters and enter the ionizing section (B).
Here each tiny particle receives a positive electrical charge.
These charged particles then enter the collecting section
(C). This section consists of a series of aluminum plates
which are alternately charged negative and positive.
Dirty Air In
Clean Air Out
The positive charge of the particles cause them to be
repelled by the positive plates and attracted to the negative
plates where they are collected . . . just as a magnet
attracts iron filings.
Figure 1
Clean-filtered air re-enters the supply duct system.
Carbon (Charcoal) Filters
White Dust (Lint)
Odors are gas molecules, not particles. They cannot be
removed by an Electronic Air Cleaner or by any other
filtration media designed to remove airborne particles.
However, some gases can be absorbed by an activated
carbon filter or diluted with fresh outdoor air. When odors
are present, the addition of charcoal filters will neutralize
odors, such as cooking odors, pet odors, cigar and ciga-
rette odors, ozone, etc. Optional charcoal filters are
available for your Air Cleaner. Refer to the parts list for the
charcoal filter part number for your Air Cleaner. Charcoal
filters require replacement. They cannot be washed. While
there is no rule of thumb for how often they should be
changed, you can use your best judgement based on the
odors you perceive in your environment.
An Electronic Air Cleaner is designed to collect two major
types of contaminants: LLIrritants (Pollens, Spores, Molds,
Bacteria, etc.) and L Black Soiling Contaminants (Dirt and
Smoke particles).
The residue on the collecting plates of an electronic air
cleaner is black, indicating it is removing dirt from the air
stream. After installing an air cleaner you may notice white
dust (typically, long linty particles or fibers – from carpets,
cotton materials or drapery fabrics). This material is not
collected by the air cleaner because it does not contain the
irritants or soiling contaminants listed above or settles out of
the air before reaching the air cleaner. The presence of
white dust does not indicate an air cleaner requires service.
CONSTRUCTION OF THE AIR CLEANER
Not only is your air cleaner easy to install, it is also easy to
operate and maintain. Its basic components, and their
functions, are as follows: (See Figure 2)
Pre-Filters
Cabinet
Handle
Cabinet - mounts to existing duct work and houses the
collecting cells and pre-filters.
Collecting Cells - are made in two sections and perform
the actual collecting of dust, dirt, and other impuri-
ties from the air. They contain the ionizing and
collection sections described above.
Each cell must be installed with the ionizing wires
on the air entering side. Each cell must be oriented
with the handles and contact button (Figure 2)
toward the operator.
Contact
Button
Pre-filters - are in two sections which are interchangeable.
They serve as a pre-filter to trap large particles
such as hair and lint before they can enter the cell
sections.
Collecting Cells
Contact
Button
Power Pack
Figure 2
Power Pack- contains operating and power on lights as well
as the solid state components that convert the 120
volt power supply to the high-voltage, direct current
required for the collecting cell.
3
PREINSTALLATION
Not to Exceed 20
(Interchangeable)
Collecting Cell
(Interchangeable)
Collecting Cell
Air Flow
Outlet Box
Cabinet
Power Pack
Handle
Air Flow
Furnace
Opening
Electronic
Air Cleaner
Opening
Contact
Button
Contact
Button
Furnace
Electronic
Air Cleaner
Pre-Filters
(Interchangeable)
Transition Section
(if Needed)
See text for Cell
Removal Clearance
Figure 4
Figure 3
LOCATING THE AIR FILTER
Knockouts for
3/4" Conduit
(three sides)
Your air filter must be mounted in the return air duct of a
central forced-air system, on the air entering side of your
furnace. (See Figure 3 for example.)
6 7/8"
Select a location that meets the following:
1. The face of the cell will be at a right angle to the air
stream.
2. Allow the following clearances to permit removal of
cells and pre-filters: (See Figures 4 and 5)
C
F
E
Model SST1000 - 14 inches
Model SST1400 - 15 inches
Model SST1600 - 14 inches
Model SST2000 - 15 inches
D
For complete dimension data refer to Figure 5.
3. The air filter is not to be placed in the discharge of
either the heating or cooling unit.
B
4. IMPORTANT: If atomizing spray type humidifier is
used, it must be installed downstream from the air
filter.
A
If your furnace duct system has a pre-installed boot,
discard front cover of boot and slide the air cleaner
component inside the boot. For installation of Air Cleaner
Retrofit (ACR) kits, see page 13.
MODEL NO.
A
B
C
D
E
F
SST1000
SST1400
SST1600
SST2000
24 3/4 21 5/16 18 5/8 13 9/16 16 7/16 19 1/16
29 11/16 26 1/4 23 5/8 13 9/16 16 7/16 19 1/16
25 1/2 21 5/16 18 5/8 17 3/4 20 5/8 23 3/8
29 11/16 26 1/4 23 5/8 17 3/4 20 5/8 23 3/8
If furnace opening cannot be enlarged to required size, a
transition sheet metal section must be used. Transition
must be planned for each job. Reduction should not be
more than 4 inches per linear foot, approximately 20
angular degrees (Figure 3).
Figure 5
tions. Turn cells upside down (with the same end facing
the cabinet opening). This will locate the ionizing wires at
the right, and both contact buttons and cell handles will be
facing the power door. Air flow direction must agree with
arrow embossed on end of collecting cells.
DIRECTION OF AIR FLOW THROUGH THE
AIR CLEANER
After installing the cell sections, install pre-filters in cabi-
net tracks on the right. This will again place the pre-filters
on the air entering side (on the same side as ionizing
wires).
Your air cleaner is shipped from the factory with air flow
from left-to-right. If this air flow is suitable for the installa-
tion, no further changes need to be made (Figure 4). For
right-to-left air flow, remove both pre-filter and cell sec-
4
TYPICALMOUNTINGPOSITIONS
Air Flow
Air Flow
Air Flow
Rear View
Rear View
Figure 6
BASEMENT FURNACE
Figure 8
Figure 7
HIGHBOY FURNACE
(Figure 8)
(LOWBOY) (Figure 6)
COUNTERFLOW
FURNACE (Figure 7)
Cleaner is mounted hori-
zontally in return plenum,
just above furnace.
Side installation. Cleaner
is mounted vertically,
where return air enters
side inlet of furnace.
Cleaner is mounted horizon-
tally in return duct or plenum,
just above furnace.
HIGHBOY FURNACE
(Figure 9)
Installation beneath furnace.
Cleaner mounts horizontally,
where return air enters from
below. Raise furnace and in-
stall beneath base.
Less than
7 Inches
Offset
At Least
9 Inches
Air Flow
Figure 10
OFFSET INSTALLATION
(Figure 10)
Figure 9
Typical use of duct offset to match air filter opening.
If duct connection to furnace allows less than nine
inches for mounting the air cleaner, shorten the
lateral trunk, or attach an offset fitting to the elbow.
Air Flow
HORIZONTAL FURNACE
(Figure 11)
Cleaner is mounted vertically
in the return duct near furnace.
Figure 11
5
INSTALLATION
REMOVE OLD FILTER AND DISCARD
(Figure 12)
NOTE:Thisfiltermaybemountedinthefurnacecompart-
ment.
CLEAN BLOWER COMPARTMENT
It is suggested that the furnace blower compartment,
blower and blower housing be cleaned to ensure clean air
circulation.
Figure 12
Power
Supply
Box
INSTALLATION
Frame
The following is a typical installation of the air cleaner on
a “Highboy” furnace (Figure 8).
Duct
1. Place the air filter cleaner on the floor. Stand it upright
with the power door facing you (Figure 4). If a
horizontalinstallationisbeingplanned,laythecleaner
on its side, this will help you to visualize the relative
location of all parts.
Allow ample space for wiring and servicing the power
supply box (Figure 13).
Mounting
Holes
2. Release the latch, remove the power pack (by grasp-
inghandleandpullingpowerpackawayfromcabinet)
and set it aside. Remove the collecting cells and pre-
filters. Set pre-filters and cells aside in a safe location
until the cabinet is installed.
Figure 13
3. Set the cabinet next to the furnace. If necessary,
enlarge the opening in the furnace (if possible) to
match the opening in the cabinet.
Turning
Vanes
Air Flow
If the furnace opening cannot be enlarged, a transi-
tion fitting should be used. (Figure 3).
The cabinet can be attached directly (Figure 13), or
a starting collar can first be fitted to the furnace inlet.
A butt or slip joint can be used.
Securely attach the cabinet to furnace inlet, using at
least two of the mounting holes on each side of the
cabinet.
Figure 14
4. Using butt joint, attach duct work (normally an elbow)
to the upstream side of air cleaner cabinet. (Note the
use of the sheet metal turning vanes inside the elbow
to improve air distribution over the face of the cells.)
(Figure 14)
NOTE: An optional method of attaching duct work to the
cabinetistomodifythecabinet(Figure15)bybendingthe
tabs outward at a 90° angle and attaching duct work to
tabs.
Optional method
(Bend tabs outward at 90˚ angle)
Figure 15
5. Connecttheverticalductsectiontotheelbow.Wedge
a wood block between floor and elbow for support
(Figure 16).
Transition Fittings
If the air duct does not fit the cabinet opening, a transition
fitting should be used. Gradual transitions are preferred
for greatest efficiency. Not more than four inches per
linear foot (approximately 20° angle) should be allowed
(Figure 3).
6. Seal all joints in the return air system downstream
from the air cleaner with duct tape to prevent dust
from entering the air stream. Tape is usually applied
ontheoutsideofducts,butmayalsobeappliedonthe
inside, or both.
6
WIRINGINSTRUCTIONS
10. With the cabinet Installed, reinstall pre-filter(s) and
7. With the cabinet installed, the air cleaner can now be
wired to electrical input source.
collecting cell(s) (Figure 19).
NOTE: The contact button and handles on the cell
must be facing you and ionizing wires must be on the
air intake side.
!
WARNING
Installation of this unit must comply with local
electric codes or other applicable codes.
11. Install the power pack as follows:
Engage the lip on lower inside edge of power pack in
the flange on cabinet and carefully close the power
pack,makingsurethattheelectricalconnectorprongs
on the power pack enter the slots in the socket on
cabinet. When the power pack is fully in place, en-
gage the latch and snap it closed.
Review and understand local codes prior to in-
stallation.
Failure to do so could result in serious personal
injury or death.
8. This air cleaner unit has no air flow monitor installed,
it does require electrical wiring through the furnace
controls. Connect wiring to the furnace control termi-
nals. (EAC-H) for power, (EAC-N) for neutral, and
connect metal frame of EAC to ground. If air flow
monitorisrequiredforoperation,orderF859-0381Air
Flow kit. Install kit and connect a 120 VAC 60 Hz input
circuit. A 20 amp circuit is more than adequate.
Floor
9. Remove junction box cover and install the required
bushing into the 3/4 in. Knock out. With the supply
voltage turned off, route three (3) wires into junction
box for connections. (See Fig. 17.)
Conduit
Insure all wires are clamped, wire connectors prop-
erly installed and grommets used to prevent wire
abrasion.
Vertical
Section
Duct
Tape All
Joints
Electronic
Air Cleaner
Figure 18
Pre-Filters
Wood Block
Cabinet
Handle
Figure 16
Hot
Neutral
Grounding
Conductor
Contact
Button
Collecting Cells
Contact
Button
Front View
Figure 17
Power Pack
Figure 19
7
OPERATION
1. With the 120 VAC power turned on at the circuit
breaker for the furnace, push the air cleaner ON-OFF
switch to the “ON” position (Figure 20).
2. With the furnace blower running, the air cleaner will
be operating. An arcing or “snapping” sound may be
heard. This will occur occasionally, however the unit
is operating properly.
3. With the furnace blower running, the Operating Light
should be ON. If the Operating Light is not ON this
signifies that the cells need washing, or that trouble
exists in the unit.
Operating
Light
If, after washing the cells, the Operating Light stays off,
the cell could be wet, improperly placed in the cabinet or
may need servicing.
On-Off
Switch
NOTE: An occasional flicker of the light accompanied by
harmless sparking or snapping noise may occur. This is
caused by trapping large particles of dirt. If arcing is
continuous, the cells should be washed or checked for
service problems see Basic SST Service Guide.
Figure 20
4. Remove the cell(s) and pre-filter(s) from cabinet.
Using a solution of warm water and low sudsing
detergent, soak cell(s) and pre-filter(s) for 20 to 30
minutes.
MAINTENANCE AND WASHING
!
CAUTION
NOTE: Ionizing wires may become coated causing
loss of cleaning ability by the collecting cell. Using a
damp cloth, wipe each ionizing wire, exercising care
not to damage them.
CABINET AND CELLS MAY CON-
TAIN SHARP EDGES.
Use care when servicing unit or
handling cells.
5. Remove the cell(s) and pre-filter(s) from solution and
rinse thoroughly with clean water.
Failure to do so could result in
minor personal injury.
6
Allow cell(s) and pre-filter(s) to drip dry for a mini-
mum of 2 hours. Cell(s) and pre-filter(s) may be
tipped at a slight angle to expedite the drip-dry
process.
For maximum efficiency your air cleaner cell(s) and pre-
filter(s) should be inspected once a month and cleaned
when necessary. Cleaning will usually be required every
one to three months, depending upon the particular
household circumstances. When cleaning is required the
following procedure should be used:
7. Reinstall the cell(s) and pre-filter(s) in the cabinet.
8. Replace the power pack. Turn furnace fan on. After
30 minutes push ON-OFF switch on the power pack
to the “ON” position.
A moderate amount of arcing or “snapping” may
occur at this time, which will indicate that the cell(s)
are still damp. If the noise is objectionable, push the
ON-OFF switch to the “OFF” position and allow
additional time for cell(s) and pre-filter(s) to dry. In
some cases the Operating Light will remain OFF
during this initial activation of the air cleaner, and this
would indicate that the cell(s) are not completely dry.
The Operating Light should remain ON while the
furnace fan is running once the drying is complete.
CLEANING THE CELLS
1. Turn the air moving system “OFF.”
2. Push the ON-OFF switch on the power pack to the
“OFF” position (Figure 20). Wait 15 seconds and both
the power pack and the collecting cell(s) will be
automatically discharged.
3. Release the latch on top of power pack and pull the
power pack straight away from cabinet at the top.
Then lift pack out of ledge at bottom edge of cabinet.
Set power pack aside.
8
REPLACING AN IONIZING WIRE
If an ionizing wire should break, it can be replaced as
follows:
1. Remove all pieces of broken wire. Make sure sup-
ports at each end are in good condition and not bent
out of shape.
2. Hook the new wire onto the support at one end.
3. Hold your finger against the support at the other end
(Figure 21) and hold the ionizing wire between thumb
and forefinger as shown or use needle nose pliers.
Press inward on spring support. Hook end of wire
over small tab at end of support and release. Make
sure wire is securely anchored at each end.
Support
Ionizing
Wire
Figure 21
SPECIFICATIONS
SPECIFICATIONS
SST1000
SST1400
SST1600
SST2000
Rated Capacity
Max. Pressure Drop
Cell Weight
600 - 1200 cfm
.08 in. W.G.
(2) 7 lbs. each
9 lbs.
1000 - 1600 cfm
.08 in. W.G.
(2) 9 lbs. each
9 lbs.
1000 - 2000 cfm
.12 in. W.G.
(2) 9 lbs. each
10 lbs.
1600 - 2200 cfm
.09 in. W.G.
(2) 9 lbs. each
10 lbs.
Power Pack Weight
Unit Weight
35 lbs.
42 lbs.
38 lbs.
45 lbs.
Power Consumption
Electrical Input
40 Watts (Max)
120 VAC 60 hz.
1.0 Ma
40 Watts (Max)
120 VAC 60 hz.
1.2 Ma
40 Watts (Max)
120 VAC 60 hz.
1.5 Ma
40 Watts (Max)
120 VAC 60 hz.
1.7 Ma
Electrical Output
@ 6450 VDC (nom)
Max. Ozone Output
Temperature Rating
.05 ppm
.05 ppm
.05 ppm
.05 ppm
40 F to 125 F
40 F to 125 F
40 F to 125 F
40 F to 125 F
9
BASIC SST SERVICE GUIDE
This guide will cover most homeowner complaints. If, after checking the items listed, the unit still fails to operate
properly, contact the nearest Authorized Service Center.
SERVICE INDICATION
SERVICE CHECKS
ON/OFF switch “ON”
Blower ON
Unit functioning Normally
Operating Light ON
ON/OFF switch “ON”
Blower ON
1. Power is not being supplied to air cleaner.
A. Check fuse or circuit breaker.
Operating Light OFF
B. Ensure power pack is properly installed and latched.
2. Collecting cell shorted - Turn power Off - Remove power pack - Remove
collecting cells - Replace power pack - Restore power (ensure blower is
operating).
A. If Operating Light comes ON check cells for bent plates, loose ionizing
wire(s) or cracked insulator(s).
B. If Operating Light remains OFF, malfunction is in the power pack. (See
power supply Checkout Procedure).
ON/OFF Switch “ON”
Blower OFF
Operating Light ON
1. Air flow sensor contaminated/misaligned
A. Remove power pack and clear contamination inside black bushing around
the small sensor element.
B. Ensure small sensor element is centered in bushing.
2. Air sensor left in bypassed condition after servicing.**
3. Faulty air flow sensor panel.
Excessive arcing during
normal operation -
Operating Light may blink
1. Wet collecting cell.
A. Allow cell(s) to dry after cleaning before applying power.
2. Damaged collecting cell(s).
A. Remove cell(s) and inspect for bent plates, loose ionizing wire(s), cracked
insulator(s), etc.
3. Collecting cells dirty.
A. Clean cells as instructed in this manual.
4. Faulty power supply (see power supply checkout procedure)
**NOTE: Your air cleaner is equipped with an air flow sensor (switch) which turns the unit ON and OFF in
response to the system blower. It may have been “wired out” during a service check and inadvertently left in this
condition
10
TECHNICAL REPAIR GUIDE
All voltage measurements indicated can be made with a
high voltage D.C. probe and a general purpose volt ohm
meter. For example: Simpson 260 or equivalent.
!
WARNING
Do not attempt repair of this unit unless you are
familiar with the necessary tools, equipment,
utility connections and potential hazards.
For test purposes, the air flow switch may be “wired out”
of the system. This will eliminate the need for air flow
across the sensing thermistor to energize the power
supply (see Fig 23).
Repair should be performed only by a qualified
service provider.
NOTE: All tests to be performed with the Ozone Reduc-
tion Jumper intact.
Failure to do so could result in reduced perfor-
mance of the unit, serious personal injury or
death.
NOTE: When servicing the power pack components, all
wiring must be routed to factory specifications.
This guide contains service checks to assist service
personnel in locating and correcting any malfunction that
might occur to render the air cleaner ineffective or inop-
erative. The air cleaner has been designed with replace-
able components, such as the high-voltage power supply
and air flow switch. This allows the serviceman to replace
a faulty component rather than attempt repairs of such
components in the field.
120 VAC
Connector
Power Pack
Assembly
L2
L1
Cover Assembly
Power Supply
Specifications
The solid-state power supply is not
designed for individual component part
replacement and must be replaced as
a complete "snap-in" unit.
Operating
Light
(If Required)
Airflow Switch
ON/OFF
Switch
Blk
Input voltage: 120 VAC 60 Hz.
Output to light: 1.5 to 2.5 VDC
H.V. Output: 6450 VDC (nom)
Wht/Brn
Wht
Blk
Red
Gnd
Collecting Cell
Specifications
Cell Contact
& Insulator
1000 cfm - 1.0 Ma @ 6450VDC
1400 cfm - 1.2 Ma @ 6450 VDC
1600 cfm - 1.5 Ma @ 6450 VDC
2000 cfm - 1.7 Ma @ 6450 VDC
Wht
Blu
Power
Supply
Wht/Brn/Air Flow
Blk
Figure 22
11
4. Using a standard extension cord, apply 120 VAC to
power pack. Turn power switch to “ON” position.
POWERSUPPLY
CHECKOUTPROCEDURE
5. Connect meter negative (-) lead to metal frame of
collecting cell. Use high voltage probe to measure
voltage at collecting cell ionizer or cell plates. Voltage
should be 6100 to 6800 VDC.
1. Turn power switch to the “OFF” position and remove
the power pack from cabinet.
2. If air flow switch is installed, locate air flow switch and
remove power pack cover. If air flow switch is not
installed, go to step 4.
NOTE:Anew“out-of-box”cellmaycausethevoltage
to be lower than normal for a short period of time. To
obtain a more accurate measurement, “age” the cell
by applying high voltage to the cell for 15 to 30
minutes.
3. Disconnectthethree-pinplasticconnectorandjumper
the two female pins (white wire to white-brown wire)
as shown in Fig. 23.
6
If voltage is below 6100 VDC, check cell for foreign
objects, bowed/bent/loose plates, broken ionizing
wires or cracked insulators. Wash cells if required. If
Operating Light remains OFF, replace collecting cell.
Plastic Connector
Male Pin
AIR FLOW MONITOR TEST
Jumper Lead
Female Pins
1. Connect a multimeter set to read 120 VAC to power
supply terminals marked “LINE.”
Method of jumping lead wires of
connector plug from air flow switch.
2. Connect 120 VAC to power pack plug, turn power
switch “ON.”
Figure 23
3. Blow on thermistor at air flow monitor. 120 VAC
should appear at multimeter. Stop blowing and volt-
age should disappear in 10 - 15 seconds.
4. Place power pack on a well insulated workbench.
Connect meter negative (-) lead to the sheet metal
chassis and the high voltage probe to high voltage
contact on back cover of power pack. Connect AC
powertopowerpackusinganextensioncordandturn
power switch to the “ON” position. Keep hands and
tools away from high voltage contact.
4. If voltage did not appear (Step 3), disconnect power
to power pack. Locate air flow switch and remove
power pack cover. Disconnect the three-pin plastic
connector. Jumper the two female pins (white wire to
white-brown wire) as shown in Fig. 23. Reconnect
power to power pack. Turn power switch “ON.”
5. If Operating Light comes ON and output voltage is
between 6100 and 6800 VDC, power supply is good.
A. If 120 VAC appears at multimeter, replace air
flow monitor.
6. If voltage is good but Operating Light does not come
on, replace Operating Light.
B. If 120 VAC does not appear on multimeter,
problem is other than air flow monitor. Recheck
all primary wiring.
CELL TEST
NOTE: The air flow monitor is designed to operate in the
temperature range of 65° to 120° F. Operation outside
this range is not recommended.
1. Place collecting cell on a well insulated workbench
with the cell contact button pointing upward.
2. Select a power pack (with air flow switch bypassed
and ozone reduction jumper intact) that reads be-
tween 6100 and 6800 VDC at the cell contact with no
cell attached.
3. Place power pack on top of collecting cell ensuring
that there is proper contact between the cell contact
on the power pack contact.
12
OZONEREDUCTION
All electronic air cleaners typically produce a small
amount of ozone that is within established limits.
Some customers may notice an odor especially at
high altitudes or low air flow rates.
W1
This power supply has a “hairpin” shaped jumper
wire labeled W1 (see Fig 24) that can be cut and
separated in case of such complaints. This will
cause the power supply to limit the maximum
operating power to a lower level.
Cut and separate
Ozone Reduction
Jumper
WHT/BRN
E3
BLK
E2
LINE
Ozone Reduction Jumper
Figure 24
ELECTRONIC AIR CLEANER RETROFIT (ACR) KITS
INSTALLATION
Pre-Filters
Cabinet
Handle
1. Removethetwopre-filtersfromthepackageandinsert
intocabinettracksoppositethefurnace. Thesewillbe
used to catch the larger particles that are in the air
stream before entering the collecting cell.
2. Insert the two collecting cells into the cabinet behind
the pre-filters. Be sure ionizing wires are directly
behind the pre-filters so the particles can be charged
as soon as the air leaves the pre-filters.
3. Removecoverplateonthepowersupplyjunctionbox
and remove the knockout needed to bring the wire to
Contact
Button
the female receptacle.
4. Positionreceptaclewithgroundinthedownpositionas
Collecting Cells
Contact
Button
shown in Fig 17 (page 7) and pull wires through the
receptacle locator on the junction box. Snap the
receptacle into the hole until secure.
5. Connectgroundwirefromreceptacleandgroundwire
in kit to cabinet with rivet and washer as follows:
a) Place washer on rivet
b) Place terminal from ground wire on rivet
c) Place terminal from receptacle ground wire on
rivet
d) Insert rivet in hole in junction box and secure.
WIRING
5. Forwiringinstallation(seepage7)andfollowallwiring
instructions 7, 8 and 9.
6. Install the power pack (see page 7) instruction 11.
7. For operation (see page 8 – Operation).
13
REPAIR PARTS
5
4
6
1
5
2
3
7
2
3
9
8
13
10
18
11
12
5
14
14
REPAIR PARTS
PARTS LIST FOR ELECTRONIC AIR CLEANERS
When ordering repair parts, always give the following information as
shown in this list.
1. The PART NUMBER
2. The PART DESCRIPTION
3. The MODEL NUMBER
4. The NAME OF ITEM - Electronic Air Cleaner.
Always order by “PART NUMBER” . . . Not by “ITEM NUMBER”
PART NUMBER
ITEM
NO.
DESCRIPTION
SST1000
SST1400
SST1600
SST2000
1
Cabinet
N/A
N/A
N/A
N/A
2
Pre-Filter
• F825-0431
• F811-0398
F838-0072
------
• F825-0432
• F811-0397
F838-0072
------
• F825-0337
• F811-0321
F838-0072
------
• F825-0338
• F811-0319
F838-0072
------
3
Collecting Cell
4
Junction Box Cover
* Screw #6 x 3/8
Connector, Female
Power Pack Assembly
Cell Handle
5
6
F818-0053
F858-1021
F832-0039
F843-0484
F844-0130
F876-0202
N/A
F818-0053
F858-1022
F832-0039
F843-0484
F844-0130
F876-0202
N/A
F818-0053
F858-1023
F832-0039
F843-0500
F844-0130
F876-0202
N/A
F818-0053
F858-1024
F832-0039
F843-0500
F844-0130
F876-0202
N/A
7
8
9
Ionizing Wire
10
11
12
13
14
15
16
17
18
Light
Switch
Power Pack, Cabinet Only
Connector, Male
Power Supply
F827-0026
F858-1002
F820-0098
37-6373
F827-0026
F858-1002
F820-0098
37-6373
F827-0026
F858-1002
F820-0220
37-6373
F827-0026
F858-1002
F820-0220
37-6373
Cover, Power Pack
† Manual
† Charcoal Filter (with mounting clips)
Air Flow Switch (monitor kit)
F825-0466
F859-0381
• F825-0467
F859-0381
• F825-0468
F859-0381
• F825-0469
F859-0381
* Standard Hardware Item
• Two (2) Required
† Not Shown
15
WASH REMINDER SCHEDULE
frequent washing may be necessary on some installa-
A regular washing schedule is necessary to ensure tions where there is new carpeting, plaster dust or exces-
proper efficiency. A thorough washing once every month sive cigarette smoke, etc. (See page 8 for maintenance
will be adequate for most installations. More or Less
and instructions on how to clean a cell.)
Year
JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC
20___
20___
20___
20___
20___
20___
20___
20___
20___
20___
20___
20___
NOTICE TO CONSUMERS
White-Rodgers
Electronic Air Cleaner
Dear Consumer;
White-Rodgers would like to thank you for purchasing a White-Rodgers Electronic Air
Cleaner or product containing a White-Rodgers Electronic Air Cleaner. Although White-
Rodgers does not extend a warranty directly to consumers, White-Rodgers does extend a
warranty to Wholesalers and Original Equipment Manufacturers who use White-Rodgers
Products. To obtain more information about how your Wholesaler or Original Equipment
Manufacturer’s warranty may benefit you, please contact your Wholesaler or Original
Equipment Manufacturer.
Sincerely,
White-Rodgers
TheEmersonlogois
trademarkandaservicemark
ofEmersonElectricCo.
|