Sharp Ar F152 User Manual

MODEL  
AR-F152  
DIGITAL LASER COPIER/FACSIMILE  
OPERATION MANUAL  
Page  
GETTING STARTED  
MAKING COPIES  
3
12  
20  
SPECIAL FUNCTIONS  
SUPPLIES AND  
USER MAINTENANCE  
23  
27  
36  
COPIER TROUBLE?  
APPENDIX  
CONTENTS  
1 GETTING STARTED  
INTRODUCTION  
CAUTIONS  
MAIN FEATURES  
PART NAMES  
OPERATION PANEL  
COPIER INSTALLATION  
3
4
5
6
7
8
CAUTIONS ON HANDLING  
9
LOADING COPY PAPER 10  
2 MAKING COPIES  
NORMAL COPYING 12  
Stream feeding mode 15  
EXPOSURE ADJUSTMENT/PHOTO COPYING 15  
REDUCTION/ENLARGEMENT/ZOOM 16  
BYPASS FEED (including special paper) 17  
TWO-SIDED COPYING 18  
SPECIAL FUNCTIONS  
3
DESCRIPTION OF SPECIAL FUNCTIONS 20  
TONER SAVE MODE 20  
USER PROGRAMS (power save modes, auto clear time,  
stream feeding mode) 21  
Setting the power save modes, auto clear time, and  
stream feeding mode 21  
DISPLAYING TOTAL NUMBER OF COPIES  
22  
1
CONTENTS  
SUPPLIES AND USER MAINTENANCE  
4
TONER CARTRIDGE REPLACEMENT 23  
Toner cartridge life 25  
USER MAINTENANCE 25  
Cabinet 25  
Original table and original cover 25  
Transfer charger 26  
When copier is not in use 26  
COPIER TROUBLE?  
5
MISFEED REMOVAL 27  
A Misfeed in the paper feed area 28  
B Misfeed in the fusing area 28  
C Misfeed in the transport area  
29  
D Misfeed in the lower paper feed area  
30  
E Misfeed in the SPF  
DEVELOPER REQUIRED  
MAINTENANCE REQUIRED  
31  
32  
32  
TROUBLESHOOTING  
33  
STATUS INDICATORS 34  
AUTOMATIC EXPOSURE ADJUSTMENT 35  
APPENDIX  
6
SPECIFICATIONS  
SUPPLIES 38  
36  
Types and sizes of copy paper  
38  
INDEX  
2
GETTING STARTED  
This chapter provides basic information for using the copier.  
1
INTRODUCTION  
This copier has been designed to provide intuitive operating ease while requiring a minimum  
amount of space. To get full use of all copier features, be sure to familiarize yourself with this  
manual and the copier.  
For quick reference during copier use, keep this manual in a handy location.  
This copier can be used as a facsimile machine.This copier can also be used  
as a laser printer if an optional printer expansion kit is installed. This manual  
describes only the copier features. For description of the facsimile and printer  
features, see their separate manual.  
Conventions used in this manual  
In this manual, the following icons are used to provide the user with information pertinent to the  
use of the copier.  
Warns the user that injury to the user or damage to the copier may result if the  
contents of the warning are not properly followed.  
Cautions the user that damage to the copier or one of its components may  
result if the contents of the caution are not properly followed.  
Notes provide information relevant to the copier regarding specifications,  
functions, performance, operation and such, that may be useful to the user.  
Indicates a letter displayed in the display.  
3
CAUTIONS  
Follow the cautions below when using this copier.  
G
The fusing area is hot.Exercise care in this area when removing misfed paper.  
G
G
Do not look directly at the light source. Doing so may damage your eyes.  
Do not switch the copier rapidly on and off.After turning the copier off, wait 10  
to 15 seconds before turning it back on.  
1
G
Copier power must be turned off before installing any supplies.  
G
G
G
Place the copier on a firm, level surface.  
Do not install the copier in a humid or dusty location.  
When the copier is not used for a long time, for example, for consecutive  
holidays, turn the power switch off and remove the power cord from the outlet.  
G
G
G
When moving the copier, be sure to turn the power switch off and remove the  
power cord from the outlet.  
Do not cover the copier with a dust cover, cloth or plastic film while the power  
is on. Doing so may prevent heat radiation, damaging the copier.  
Use of controls or adjustments or performance of procedures other than those  
specified herein may result in hazardous radiation exposure.  
SAFETY PRECAUTIONS  
This Digital Copier is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the  
CDRH standards.This means that the copier does not produce hazardous laser radiation.  
For your safety, observe the precautions below.  
G
Do not remove the cabinet, operation panel or any other covers.  
The copiers exterior covers contain several safety interlock switches. Do not bypass  
G
any safety interlock by inserting wedges or other items into switch slots.  
4
MAIN FEATURES  
High-speed laser copying  
G
Since warm-up time is zero, copying can be started immediately after the power switch is  
turned on.  
G
First-copy time is only 9.6 seconds (normal mode).  
1
G
Copying speed is 15 copies/min., which adapts to business use, allowing improvement  
of working efficiency.  
High-quality digital image  
G
High-quality image copying at 600 dpi can be performed.  
G
In addition to the automatic exposure mode, the manual exposure can be adjusted in five  
steps.  
G
The photo mode copying function allows clear copying of delicate halftone original images  
such as monochrome photos and color photos.  
Substantial copying functions  
G
Zoom copying from 50% to 200% in 1% increments can be performed.  
G
Continuous copying of maximum 99 sheets can also be performed.  
G
Automatic document feeding through the single pass feeder (SPF) can be performed.  
G
Toner save mode reduces toner consumption by approximately 10%.  
G
User programs allow setting/modification of functions for customers needs.  
Scan once/ Print many  
G
This copier is equipped with a 1-page memory buffer. This Memory allows the  
copier to scan an original once only and make up to 99 copies. This feature allows for  
improved workflow, reduced operating noise from the copier and reduced wear and tear  
on the scanning mechanism.This feature provides for a higher reliability.  
Printer feature  
G
This copier can be used as a laser printer by installing an optional printer expansion kit.  
Environmentally friendly design  
G
Paper output tray is housed in the copier for space saving.  
G
Preheat and auto power shut-off modes are provided to reduce power consumption in  
standby mode.  
5
PART NAMES  
Original guides  
SPF exit area  
Document  
feeder tray  
Original table  
1
Feeding roller cover  
Original cover  
Operation  
panel  
Side cover  
Bypass tray  
Bypass tray guides  
Paper tray  
Handle  
Cover for optional printer interface  
* A GDI expansion kit is optional.  
Side cover  
open button  
Front cover  
Paper output  
tray  
Toner cartridge lock release  
lever  
Paper output tray  
extension  
Power cord socket  
Handle  
Power switch  
Toner cartridge  
Transfer charger  
Fusing unit  
release lever  
Charger cleaner  
Photoconductive drum  
6
OPERATION PANEL  
1
ON LINE indicator  
Exposure mode selector key and  
indicators  
Use to sequentially select the exposure  
modes: AUTO, MANUAL or PHOTO.  
Selected mode is shown by a lit indicator.  
(p. 15)  
Lights up when the machine is used as a  
printer. To use as a printer, an optional  
printer expansion kit is needed.  
Power save indicator  
Lights up when the copier is in a power save  
mode. (p. 20, 21)  
Light and dark keys and exposure  
indicators  
Use to adjust the MANUAL or PHOTO  
exposure level. Selected exposure level is  
shown by a lit indicator. (p. 15)  
Tray select key  
Use to select a paper feed station (paper  
tray or bypass tray). (p. 18)  
Paper feed location indicators  
Light up to show the selected paper feed  
station.  
Use to start and terminate user program  
setting. (p. 21)  
Alarm indicators  
Zoom keys  
: Developer replacement required  
Use to select any reduction or enlargement  
copy ratio from 50% to 200% in 1%  
increments. (p. 16)  
indicator (p. 32)  
: Misfeed indicator (p. 27)  
: Toner cartridge replacement  
required indicator (p. 23)  
Copy quantity keys  
G
Use to select the desired copy quantity  
: Maintenance indicator (p. 32)  
(1 to 99). (p. 14)  
Use to make user program entries.  
SPF indicator (p. 13)  
G
SPF misfeed indicator (p. 27)  
Copy ratio selector key and copy ratio  
indicators  
Use to sequentially select preset reduction/  
enlargement copy ratios.  
(p. 21)  
Clear key  
Press to clear the display, or press during  
a copy run to terminate copying. (p. 14)  
Press and hold down during standby to  
display the total number of copies made  
to date. (p. 22)  
G
G
Selected copy ratio is shown by a lit indica-  
tor. (p. 16)  
Zoom indicator (p. 16)  
Print key and ready indicator  
Copying is possible when the indicator is  
G
Copy ratio display (%) key (p. 16)  
on.  
Display  
G
Use to set a user program.  
Displays the specified copy quantity, zoom  
copy ratio, user program code, and error  
code.  
7
COPIER INSTALLATION  
Improper installation may damage the copier.Please note the following during initial installation  
and whenever the copier is moved.  
If the copier is moved from a cool place to a warm place, condensation may  
form inside the copier. Operation in this condition will cause poor copy quality  
and malfunctions. Leave the copier at room temperature for at least 2 hours  
before use.  
1
Do not install your copier in areas that are:  
G
damp, humid, or very dusty  
G
exposed to direct sunlight  
G
poorly ventilated  
G
subject to extreme temperature or humidity  
changes, e.g., near an air conditioner or  
heater.  
The copier should be installed near an accessible power outlet  
for easy connection.  
Be sure to connect the power cord only to a power outlet that  
meets the specified voltage and current requirements.  
Also make certain the outlet is properly grounded.  
Connect the copier to a power outlet which is not used  
for other electric appliances. If a lighting fixture is  
connected to the same outlet, the light may flicker.  
8
COPIER INSTALLATION  
8"(20 cm)  
Be sure to allow the required space around  
the machine for servicing and proper  
ventilation.  
8"(20 cm)  
4"  
(10 cm)  
4"  
(10 cm)  
1
A small amount of ozone is produced within the copier during operation. The emission  
level is insufficient to cause any health hazard.  
NOTE:  
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3)  
calculated as an 8 hr. time-weighted average concentration.  
However, since the small amount that is emitted may have an objectionable odor, it is  
advisable to place the copier in a ventilated area.  
CAUTIONS ON HANDLING  
Be careful in handling the copier as follows to maintain the performance of this copier.  
Do not drop the copier, subject it to shock  
or strike it against any object.  
Store spare toner cartridges in a cool dry place without removing from the  
package before use.  
If they are exposed to direct sunlight or excessive heat, poor print quality may result.  
Do not touch the photoconductive drum (green portion).  
Scratches or smudges on the drum will cause dirty copies.  
9
LOADING COPY PAPER  
This copier is equipped with two paper trays. Load copy paper into the two  
paper trays.  
Raise the handle of the paper tray and pull the paper tray out until it stops.  
1
Adjust the paper guides on the paper tray to the copy paper width and length.  
Squeeze the lever of paper guide  
paper.  
and slide the guide to match with the width of the  
Move paper guide  
to the appropriate slot as marked on the tray.  
Paper guide B  
Paper guide A  
Fan the copy paper and insert it into the tray.Make sure the edges go under the corner  
hooks.  
Do not load paper above the maximum height line (  
will cause a paper misfeed.  
). Exceeding the line  
10  
LOADING COPY PAPER  
Gently push the paper tray back into the copier.  
After loading copy paper, to cancel the blinking Pwithout restarting copying,  
press the clear ( ) key. The Pin the display will go out and the ready (  
)
indicator will light up.  
1
11  
MAKING COPIES  
This chapter describes basic copying functions and some other copying functions using the  
bypass tray.  
NORMAL COPYING  
This copier has two document input stations - a single pass feeder (SPF) for automatic document  
feeding and an original table for manual handling of documents.The SPF is designed to hold up  
to 30 originals measuring from 5-1/2" x 8-1/2" to 10" x 14" and weighing from 14 to 23 lbs.  
2
Ensure that paper of the desired size is set in the paper tray. See page 10, LOADING  
COPY PAPER. When copying onto paper larger than 8-1/2" x 11" size, pull out the  
paper output tray extension. Use the tray select (  
) key to select the desired paper  
tray.  
Turn the power switch on.  
The ready (  
) indicator will light up.  
G
The copier will enter a power save mode once the set time has elapsed without  
any copier operation after the last copy of a run is made or power is turned  
on.  
The settings of the power save modes can be modified. See page 21, USER  
PROGRAMS.  
The copier will return to the initial settings a preset amount of time after the  
last copy is made.The preset amount of time (auto clear time) can be changed.  
See page 21, USER PROGRAMS.  
G
12  
NORMAL COPYING  
Place the original(s) face up in the document feeder tray or face down on the original  
table.  
A. When using the SPF:  
(1) Make sure that no original is left on the original table.  
(2) Adjust the original guides to the size of originals.  
(3) Set the originals face up in the document feeder tray.  
G
Before feeding originals in the document feeder tray, be sure to remove any  
staples or paper clips from them.  
Before placing curled or wavy originals into the document feeding tray, be  
G
sure to flatten them. If not, original misfeeds may result.  
The SPF ( ) indicator on the operation panel will light up. If this indicator  
does not light up, the originals are not properly set or the SPF is not properly  
closed.  
Badly damaged originals may misfeed in the SPF. It is recommended that  
2
G
G
such originals be copied from the original table.  
Special originals such as transparency film should not be fed through the  
G
SPF, but should be placed directly on the original table.  
Original face up  
B. When using the original table:  
(1) Open the original cover.  
(2) Place an original face down on the original table.Align it with the original scale  
and the centering ( ) mark. Close the original cover.  
Original scale  
mark  
13  
NORMAL COPYING  
When copying a book or an original which has been folded or a crumpled original,  
press down the original cover lightly. If the original cover is not securely closed,  
the copies may be striped or blurred.  
A book, an original which has been  
folded, or a crumpled original  
2
Press the tray select ( ) key to select the desired tray.  
Set the number of copies using the two copy quantity (  
,
) keys.  
G
Press the clear ( ) key to clear an entry if a mistake is made.  
G
A single copy can be made with the initial setting, i.e., when 0is displayed.  
G
Press the right copy quantity key to set the units  
digit from 0 to 9.This key will not change the tens  
digit.  
G
Press the left copy quantity key to set the tens  
digit from 1 to 9.  
Tens digit  
Units digit  
) key.  
Press the print (  
G
To display the number of copies made in a continuous run, press the left copy  
quantity key.  
G
To stop copying in the middle of a run, press the clear ( ) key. Copying will  
stop and the number in the display will be reset to 0.  
14  
NORMAL COPYING  
Stream feeding mode  
The stream feeding mode allows easy operation of continuous copying from the SPF.  
If the stream feeding mode has been enabled using user program No.4, the SPF ( ) indicator  
will blink for approximately 5 seconds after the last original has been fed by the SPF. While this  
indicator is blinking, any new originals placed in the document feeder tray will be fed and copied  
automatically.If the stream feeding mode has been disabled, the print (  
) key must be pressed  
each time the originals are set even immediately after completion of a copy run from the SPF.  
The default setting of the stream feeding mode is OFF. See page 21, USER PROGRAMS.  
While the copier is in the streaming feeding mode for copying, do not set any  
originals for facsimile transmission.  
2
EXPOSURE ADJUSTMENT/PHOTO COPYING  
Copy density adjustment is not required for most originals in the automatic exposure mode.To  
adjust the copy density manually or to copy photographs, the exposure level can be adjusted in  
five steps manually.  
Set the original and check the copy paper size.  
Press the exposure mode selector key to select the manual (  
mode.  
) mode or photo (  
)
Use the light ( ) and dark ( ) keys to adjust the exposure level.  
If exposure level 2 is selected, the two left-handmost indicators for that level will light  
up simultaneously.Also, if level 4 is selected, the two right-handmost indicators for that  
level will light up simultaneously.  
Set the number of copies using the copy quantity (  
) key.  
,
) keys and press the print  
(
15  
REDUCTION/ENLARGEMENT/ZOOM  
Three preset reduction ratios and two enlargement ratios can be selected.The zoom function  
enables copy ratio selection from 50% to 200% in 1% increments.  
Set the original and check the copy paper size.  
Use the copy ratio selector key and/or zoom (  
ratio.  
,
) keys to select the desired copy  
G
To verify a zoom setting without changing the zoom ratio, press and hold  
down the copy ratio display (%) key.When the key is released, the display will  
return to the copy quantity display.  
To reset the ratio to 100%, press the copy ratio selector key repeatedly until  
the 100% indicator lights up.  
2
G
To select a preset copy ratio:  
To select a zoom ratio:  
When a zoom ( or  
the ZOOM indicator will light up and the  
zoom ratio will be displayed in the display.  
) key is pressed,  
Preset reduction and enlargement ratios  
are: 50%, 64%, 78%, 129%, and 200%  
To decrease or increase the zoom ratio rapidly, press and hold down the  
or  
key. However, the value will stop at the preset reduction or enlargement  
ratios.To move beyond these ratios, release the key and then press and hold it  
down again.  
Set the number of copies using the copy quantity (  
) key.  
,
) keys and press the print  
(
16  
BYPASS FEED (including special paper)  
The bypass tray automatically feeds up to 50 sheets of standard copy paper and also feeds  
special papers such as transparency film and labels one sheet at a time.Copy paper measuring  
from 3-1/2" x 5-1/2" to 8-1/2" x 14" and in the weight range of 14 to 34.5 lbs. can be used in this  
tray. (For paper weighing from 28 to 34.5 lbs., 8-1/2" x 11" is the maximum size.)  
Place the original(s) face up in the document feeder tray or face down on the original  
table.  
2
The original image must be smaller than the paper or media for copying.  
If the original image is bigger than the paper or media, this may cause smudges  
on the edges of the copies.  
Open the bypass tray and extend the tray.  
To close the bypass tray, perform  
step1 and then step 2 in the  
illustration and push the round  
projections at the right of the tray  
until the tray clicks into place.  
Set the paper guides to the copy paper width. Insert the copy paper (print face down)  
all the way into the bypass tray.  
G
Paper must be fed narrow side into the feed slot.  
Transparency film, labels, and other special purpose papers must be fed  
G
individually.  
G
When copying onto transparency film, remove each copy promptly. Do not let  
copies stack up.  
When loading an envelope, make sure that it is straight and flat.  
G
17  
BYPASS FEED  
Print face  
Press the tray select (  
using standard copy paper. Press the print (  
) key to select the bypass tray. Set the number of copies if  
2
) key.  
TWO-SIDED COPYING  
Two-sided copying can be made on this copier using the bypass tray.  
Example: The following two originals will be copied onto two sides of copy paper.  
Face up or face down  
Face down  
Face up  
First original  
Second original  
Place the first original on the original table and make a copy.  
The first copy can be made using either the paper tray or the bypass tray.  
Replace the first original with the second original on the original table and close the  
original cover. Make sure that the first and second originals are oriented in the same  
way on the original table.  
Both the first and second originals can be set in the SPF but they must be set  
separately. If the stream feeding mode for the SPF has been enabled, set the  
second original after the SPF ( ) indicator goes out. See page 15.  
18  
TWO-SIDED COPYING  
For tablet binding, turn the first copy over left to right as shown below. For booklet  
binding, turn the first copy over top to bottom (not shown). Feed the first copy into the  
bypass tray.  
Press the tray select (  
) key to select the bypass tray and press the print (  
) key.  
Be sure to feed the copy paper one sheet at a time.  
2
19  
SPECIAL FUNCTIONS  
This chapter describes the special functions of this copier. Use these functions as needed.  
DESCRIPTION OF SPECIAL FUNCTIONS  
Toner save mode (page 20)  
Reduces toner consumption by approximately 10%.  
Power save modes (page 21)  
The copier has two power save modes of operation: preheat mode and auto power shut-off  
mode.  
3
G
Preheat mode  
When the copier enters the preheat mode, the power save ( ) indicator will light up and  
other indicators will remain on or off as before. In this condition, the fuser in the copier is  
maintained at a lower heat level, thereby saving power.To exit from the preheat mode, press  
any key including keys on the operation panel for facsimile or place originals in the SPF.  
G
Auto power shut-off mode  
When the copier enters the auto power shut-off mode, the power save ( ) indicator will light  
up and other indicators will go out.The auto power shut-off mode saves more power than the  
preheat mode but requires a longer time before starting copying.To exit from the auto power  
shut-off mode, press the print (  
) key or any key on the operation panel for facsimile or  
place originals in the SPF. (When the print (  
shut-off mode, copying will not start.)  
) key is pressed once to exit the auto power  
Auto clear (page 21)  
The copier returns to the initial settings a preset amount of time after the last copy is made.This  
preset amount of time (auto clear time) can be changed.  
Stream feeding mode (page 21)  
For description of the stream feeding mode, see page 15.  
TONER SAVE MODE  
Press the exposure mode selector key to select the manual (  
) mode.  
20  
TONER SAVE MODE  
Press and hold down the exposure mode selector key for approximately 5 seconds.  
The manual (  
) indicator will go out and the photo ( ) indicator will begin to blink.  
The exposure indicator marked 5will light up, indicating the standard toner mode is  
active.  
To enter the toner save mode, press the light ( ) key.  
The exposure indicator marked 1will light up, indicating the toner save mode is  
selected.  
3
Press the exposure mode selector key twice.The photo ( ) indicator will stop blinking  
and the AUTO indicator will light up steadily.The toner save mode is now active.  
To return to the standard mode, repeat the procedure but use the dark ( ) key  
to select exposure level 5in step 3.  
USER PROGRAMS (power save modes, auto clear  
time, stream feeding mode)  
The user programs allow the parameters of certain functions to be set, changed, or canceled  
as desired.  
Setting the power save modes, auto clear time, and stream feeding mode  
Press and hold down the light ( ) and dark ( ) keys simultaneously for more than  
5 seconds until all the alarm indicators (  
the display.  
,
,
and ) blink and “– –” appears in  
Use the left copy quantity ( ) key to select a user program number (1: auto clear  
time, 2: preheat mode, 3: auto power shut-off timer, 4: stream feeding mode, 5: auto  
power shut-off mode).The selected number will blink in the left side of the display.  
21  
USER PROGRAMS  
Press the print (  
) key. The entered program number will be steadily lit and the  
currently selected parameter number for the program will blink on the right side of the  
display.  
Select the desired parameter using the right copy quantity ( ) key. The entered  
parameter number will blink on the right of the display.  
Program  
No.  
Mode  
Parameters  
1
Auto clear time  
0
3
OFF  
90 sec.  
1
4
30 sec. * 2  
120 sec.  
60 sec.  
10 sec.  
5
2
3
Preheat mode  
0
30 sec.  
1
60 sec. * 2 90 sec.  
Auto power shut-  
off timer  
0
3
2 min. * 1  
30 min.  
5 min.  
2
5
15 min.  
4
60 min.  
120 min.  
3
4
5
Stream feeding  
mode  
* 0  
OFF  
1
ON  
Auto power shut-  
off mode  
0
OFF  
* 1  
ON  
Factory default settings are indicated with an asterisk (*).  
Press the print ( ) key.The right-hand number in the display will be steadily lit and  
the entered value will be stored.  
To change the setting or to set another mode, press the clear ( ) key. The  
copier will return to step 2.  
Press the light ( ) or dark ( ) key to return to the normal copy mode.  
DISPLAYING TOTAL NUMBER OF COPIES  
Use the following procedure to display the total number of copies.  
Press the clear ( ) key to reset the display to zero.  
Press and hold down the clear ( ) key for approximately 5 seconds.The total number  
of copies will appear in two steps, each with three digits.  
Example:Total number of copies is 1,234.  
22  
SUPPLIES AND USER MAINTENANCE  
This chapter describes how to replace the toner cartridge.  
Be sure to use only genuine SHARP parts and supplies.  
TONER CARTRIDGE REPLACEMENT  
When the toner cartridge replacement required ( ) indicator lights up, replacement of the  
toner cartridge will be needed soon.Obtain a new cartridge.When the toner cartridge replacement  
required ( ) indicator blinks, the toner cartridge must be replaced before copying can be  
resumed. Replace the toner cartridge by following the procedure below.  
During long copy run of a dark original, the ready (  
) indicator may blink,  
4
the  
indicator light up, and the copier stop, even though toner is left. The  
copier will feed toner up to 2 minutes and then the ready (  
) indicator will  
light up. Press the print (  
) key to restart copying.  
Ensure that the bypass tray is open and then open the side cover while pressing the  
side cover open button.  
Then, push gently on both sides of the front cover to open the cover.  
Push the toner cartridge lock release lever and pull the toner cartridge out.Dispose of  
the old toner cartridge in accordance with local regulations.  
Toner cartridge lock release  
lever  
After removing the toner cartridge, do not shake it or tap on it. Doing so may  
cause a spill of toner.  
23  
11chap-4.p65  
23  
18/10/00, 19:41  
TONER CARTRIDGE REPLACEMENT  
Remove the toner cartridge from the bag. Hold the cartridge on both sides and shake  
it horizontally four or five times.  
4 or 5 times  
Gently insert the toner cartridge along the guides until it locks in place while pushing  
the lock release lever. Pull out the shutter and remove it from the toner cartridge as  
shown in the illustration  
4
Close the front cover and then the side cover by pressing the round projections near  
the side cover open button.The  
will light up.  
indicator will go out and the ready (  
) indicator  
When closing the covers, be sure to close the front cover securely and then  
close the side cover.If the covers are closed in the wrong order, the covers may  
be damaged.  
24  
TONER CARTRIDGE REPLACEMENT  
Toner cartridge life  
To find out the approximate quantity of toner remaining, follow the procedure below.  
Press and hold down the light ( ) and dark ( ) keys simultaneously for more than  
5 seconds until all the alarm indicators (  
the display.  
,
,
and ) blink and “– –” appears in  
Press and hold down the copy ratio display ( ) key for more than 5 seconds.  
G
The approximate quantity of toner remaining will be indicated in the display as a  
percentage . ( “100”, “75”, “50”, “25”, or “10” is displayed.) When the percentage is  
less than 10%,  
will be displayed.  
Press the light ( ) or dark ( ) key.  
G
All the alarm indicators will go out.  
4
USER MAINTENANCE  
Proper care is essential in order to get clean, sharp copies. Be sure to take a few minutes to  
regularly clean the copier.  
Before cleaning, be sure to turn the power switch off and remove the power  
cord from the outlet.  
Do not use thinner, benzene or other volatile cleaning agents. Doing so may  
cause deformation, discoloration, deterioration or malfunction.  
Cabinet  
Wipe the cabinet with a soft, clean cloth.  
Original table and original cover  
Stains on the glass, cover or SPF roller will also be copied.Wipe the glass, cover and SPF roller  
with a soft, clean cloth. If necessary, dampen the cloth with a glass cleaner.  
Original table  
Original cover  
SPF roller  
25  
11chap-4.p65  
25  
19/10/00, 11:56  
USER MAINTENANCE  
Transfer charger  
If copies start becoming streaky or blotchy, the transfer charger may be dirty.Clean the charger  
using the following procedure.  
Turn the power switch off.  
Ensure that the bypass tray is open and then open the side cover while pressing the  
side cover open button.  
Take the charger cleaner out by holding the tab.  
Set the charger cleaner onto the right end of the transfer charger, gently slide the  
cleaner to the left end, and then remove it. Repeat this operation two or three times.  
Slide the charger cleaner from the right end to the left end along the groove of  
the transfer charger. If the cleaner is stopped on the way, smudges on copies  
may occur.  
4
Return the charger cleaner to its original position.Close the side cover by pressing the  
round projections near the side cover open button.  
Turn the power switch on.  
When copier is not in use  
To prevent entry of dust and foreign matter, store the copier as follows.  
Remove the power cord and secure the copier using tape (four locations).  
26  
COPIER TROUBLE?  
This chapter describes misfeed removal and troubleshooting.  
MISFEED REMOVAL  
When the misfeed ( ) indicator blinks or  
blinks in the display, the copier will stop because  
of a misfeed.  
If a misfeed occurs when using the SPF, a number may appear in the display after a minus sign.  
This indicates the number of the originals that must be returned to the document feeder tray  
after a misfeed.Return the required number of originals.Then this number will disappear when  
copying is resumed or the clear ( ) key is pressed.  
When the SPF misfeeds an original sheet, the copier will stop and the SPF misfeed ( ) indicator  
will blink, while the misfeed ( ) indicator will remain off. For a misfeed of originals in the SPF,  
see E Misfeed in the SPFon page 31.  
This copier is turned on with the lower side cover open, the misfeed ( ) indicator  
will blink.In this case, close the lower side cover.The misfeed ( ) indicator will  
go out.  
5
Ensure that the bypass tray is open and then open the side cover while pressing the  
side cover open button.  
Check the misfeed location. Remove the misfed paper following the instructions for  
each location in the illustration below.  
If  
blinks in the display, proceed to A Misfeed in the paper feed area. (p. 28)  
If paper is misfed here, proceed to “B  
Misfeed in the fusing area”. (p. 28)  
If the misfed paper is seen from  
this side, proceed to “C Misfeed  
in the transport area”. (p. 29)  
If paper is misfed here, proceed to “A  
Misfeed in the paper feed area”. (p. 28)  
If paper is misfed here, proceed to “D Misfeed in the  
lower paper feed area”. (p. 30)  
27  
MISFEED REMOVAL  
A Misfeed in the paper feed area  
Gently remove the misfed paper from the paper feed area as shown in the illustration.  
When  
blinks in the display and the misfed paper is not seen from the paper feed  
area, pull out the paper tray and remove the misfed paper. If the paper cannot be  
removed, proceed to “B Misfeed in the fusing area”.  
The fusing unit is hot.Do not touch the fusing unit when removing misfed paper.  
Doing so may cause a burn or other injury.  
G
Do not touch the photoconductive drum (green portion) when removing the  
misfed paper.Doing so may damage the drum and cause smudges on copies.  
If the paper has been fed through the bypass tray, do not remove the misfed  
G
paper through the bypass tray.Toner on the paper may stain the paper transport  
area, resulting in smudges on copies.  
5
Close the side cover by pressing the round projections near the side cover open button.  
The misfeed ( ) indicator will go out and the ready (  
) indicator will light up.  
B Misfeed in the fusing area  
Lower the fusing unit release lever by rotating it all the way as shown in the illustration.  
While you are lowering the fusing unit release lever, it will not move smoothly at  
a location on the way. However, be sure to lower the lever by rotating it all the  
way to the location where it will not rotate as shown in the right illustration.  
Fusing unit release lever  
Gently remove the misfed paper from under the fusing unit as shown in the illustration.  
If the paper cannot be removed, proceed to C Misfeed in the transport area.  
The fusing unit is hot.Do not touch the fusing unit when removing misfed paper.  
Doing so may cause a burn or other injury.  
28  
MISFEED REMOVAL  
G
G
Do not touch the photoconductive drum (green portion) when removing the  
misfed paper.Doing so may damage the drum and cause smudges on copies.  
Do not remove the misfed paper from above the fusing unit. Unfixed toner on  
the paper may stain the paper transport area, resulting in smudges on copies.  
Raise the fusing unit release lever and then close the side cover by pressing the round  
projections near the side cover open button.The misfeed ( ) indicator will go out and  
the ready (  
) indicator will light up.  
C Misfeed in the transport area  
Lower the fusing unit release lever by rotating it all the way as shown in the illustration.  
5
While you are lowering the fusing unit release lever, it will not move smoothly at  
a location on the way. However, be sure to lower the lever by rotating it all the  
way to the location where it will not rotate as shown in the right illustration.  
Fusing unit release lever  
Push gently on both sides of the front cover to open the cover.  
29  
MISFEED REMOVAL  
Rotate the feeding roller in the direction of the arrow and gently remove the misfed  
paper from the exit area.  
Feeding roller  
Raise the fusing unit release lever, close the front cover and then close the side cover  
by pressing the round projections near the side cover open button.The misfeed (  
indicator will go out and the ready ( ) indicator will light up.  
)
When closing the covers, be sure to close the front cover securely and then  
close the side cover.If the covers are closed in the wrong order, the covers may  
be damaged.  
5
D Misfeed in the lower paper feed area  
Open the lower side cover (under the bypass tray) and remove the misfed paper.  
If  
blinks and the misfed paper is not seen from the area of the lower side cover,  
pull out the lower paper tray and remove the misfed paper.Then close the lower paper  
tray.  
Close the lower side cover.  
Close the side cover by pressing the round projections near the side cover open button.  
The misfeed ( ) indicator will go out and the ready (  
) indicator will light up.  
30  
MISFEED REMOVAL  
E Misfeed in the SPF  
An original misfeed may occur at one of three locations: if the misfed original is seen from the  
document feeder tray, (A) in the document feeder tray;if the misfed original is not seen from the  
document feeder tray, (B) in the exit area or (C) under the feeding roller. Remove the misfed  
original following the instructions for each location.  
(A) Open the feeding roller cover and pull the original gently to the left and out from the  
document feeder tray. Close the feeding roller cover. Open and close the original cover to  
clear the SPF misfeed ( ) indicator.  
If the misfed original cannot be easily removed, proceed to (C) without pulling the original  
forcibly from the document feeder tray.  
Feeding roller cover  
(B) Open the original cover and rotate the roller rotating knob to remove the misfed original  
from the exit area.  
If the misfed original cannot be easily removed, proceed to (C) without pulling the original  
forcibly.  
5
Roller rotating knob  
(C) If the original does not move easily into the exit area, remove it in the direction of the arrow  
while rotating the knob.  
A number may appear in the display after a minus sign, indicating the number of  
the originals that must be returned to the document feeder tray.  
Clear the misfeed and return the required number of originals.Then press the  
print (  
) key to resume copying.  
31  
DEVELOPER REQUIRED  
When the  
indicator lights up, the developer should be replaced.DEVELOPER  
REPLACEMENT SHOULD ONLY BE DONE BY AN AUTHORIZED SHARP SERVICE  
TECHNICIAN. Contact your service center as soon as possible.  
MAINTENANCE REQUIRED  
When  
indicator lights up, service by an authorized SHARP service technician is required.  
Contact your service center as soon as possible.  
5
32  
TROUBLESHOOTING  
If any problem occurs, check the list below before contacting your SHARP service center.  
See  
page:  
Problem  
Possible cause  
Solution  
_
Copier plugged in?  
Plug the copier into a grounded  
outlet.  
Power switch on?  
Side cover closed  
securely?  
Turn the power switch on.  
Gently close the side cover.  
12  
_
Copier does not  
operate.  
Front cover closed?  
Gently close the front cover and  
then close the side cover.  
_
Is the original placed face  
down on the original table  
or face up in the SPF?  
Place the original face down on  
the original table or face up in  
the SPF.  
13  
Blank copies  
Press any key to cancel the  
preheat mode.  
Is the copier in the  
preheat mode?  
20  
20  
Power save (  
indicator on.  
)
Is the copier in the auto  
power shut-off mode?  
Press the print (  
) key to  
cancel the auto power shut-off  
mode.  
5
Adjust the exposure manually.  
Is original image too dark  
or too light?  
Is the copier in the  
automatic exposure  
mode?  
15  
35  
Copies are too  
dark or too light.  
Adjust the automatic exposure  
level.  
Cancel the photo exposure  
mode.  
Is the copier in the photo  
exposure mode?  
15  
Original table or original  
cover dirty?  
Original smudged or  
blotchy?  
Clean regularly.  
25  
_
Dust, dirt,  
smudges appear  
on copies.  
Use a clean original.  
Is transfer charger clean?  
Non-standard paper used?  
Clean the transfer charger.  
Striped copies  
26  
38  
Use standard paper. If using  
special papers, feed the paper  
through the bypass tray.  
Paper curled or damp?  
Store copy paper flat in the  
wrapper in a dry location.  
Remove all pieces of misfed  
paper.  
Set the guides properly  
depending on the paper size.  
Remove excessive paper from  
the tray.  
Use copy paper within the  
specified range.  
Replace with dry copy paper. If  
the copier is not used for a long  
time, remove the paper from the  
paper tray and store it in its  
wrapper in a dry location.  
_
Paper misfeeds  
frequently.  
Pieces of paper inside  
copier?  
Paper guides in the paper  
tray not set properly?  
Too much paper in the  
paper tray or bypass tray?  
Is the copy paper too  
heavy?  
27  
10  
10  
38  
Images rub off  
the copy easily.  
Paper damp?  
39  
33  
STATUS INDICATORS  
When the following indicators light up or blink on the operation panel or the following alphanumeric  
codes appear in the display, solve the problem immediately referring to both the table below and  
the relevant page.  
Be sure to use only genuine SHARP parts and supplies.  
See  
Indication  
Developer  
replacement  
required indicator  
Cause and remedy  
page:  
32  
Developer is required. Contact your SHARP  
service center as soon as possible.  
Steadily  
lit  
_
Replacement of toner cartridge will be needed  
soon. Obtain a new cartridge.  
Steadily  
lit  
Toner cartridge  
replacement  
Toner cartridge must be replaced. Replace it with  
a new one.  
required indicator  
23  
27  
Blinking  
A misfeed has occurred. Remove the misfed  
paper referring to the description of “Misfeed  
removal.”  
Misfeed indicator Blinking  
5
_
The lower side cover may be open. If so, close it.  
Maintenance  
indicator  
Steadily Service by an authorized SHARP service  
32  
lit  
technician is required.  
An original misfeed has occurred in the SPF.  
Remove the misfed originals referring to the  
description of “Misfeed in the SPF”.  
31  
SPF misfeed  
indicator  
Blinking  
_
The paper tray is not installed properly.  
Push the tray into the copier securely.  
The paper tray indicator  
is blinking.  
23  
“CH” is blinking in the  
display.  
The toner cartridge is not installed. Install the toner  
cartridge. If “CH” is blinking even if the cartridge is  
installed properly, contact your SHARP service  
center immediately.  
_
Side cover is open. Close the side cover securely  
by pressing the round projections near the side  
cover open button.  
“CH” is steadily lit in the  
display.  
Paper tray or bypass tray is empty. Load copy  
paper.  
10  
“P” is blinking in the display.  
A misfeed has occurred in the paper tray or  
bypass tray. Remove the misfed paper.  
27  
_
The copier will not function. Turn the power  
switch off, remove the power cord from the  
outlet, and contact your SHARP service center.  
A letter and a number  
appear alternately.  
The memory backup function for facsimile maintains data only for approximately  
one hour. When any facsimile data is kept in memory, do not keep the copier  
power turned off (by unplugging the power cord) for a long time even if the  
copier stops due to trouble.  
34  
AUTOMATIC EXPOSURE ADJUSTMENT  
The automatic exposure level can be adjusted to suit your copying needs. This level is set for  
copying from the original table and copying from the SPF respectively.  
When adjusting the automatic exposure level for copying from the SPF, place an original  
in the document feeder tray and make sure that the SPF ( ) indicator lights up.  
When adjusting the level for copying from the original table, make sure that no original  
is left in the document feeder tray.  
Press the exposure mode selector key to select the photo ( ) mode.  
Press and hold down the exposure mode selector key for approximately 5 seconds.  
The photo ( ) indicator will go out and the AUTO indicator will begin to blink. One or  
two exposure indicators corresponding to the automatic exposure level which has  
been selected will light up.  
5
Press the light ( ) or dark ( ) key to lighten or darken the automatic exposure level  
as desired.  
If exposure level 2 is selected, the two left-handmost indicators for that level will light  
up simultaneously.Also, if level 4 is selected, the two right-handmost indicators for that  
level will light up simultaneously.  
Press the exposure selector key. The AUTO indicator will stop blinking and light up  
steadily.  
This automatic exposure level will remain in effect until you change it again by  
this procedure.  
35  
APPENDIX  
SPECIFICATIONS  
Type  
Digital laser copier/facsimile, desk-top type  
Dry, electrostatic transfer  
Copy system  
Originals  
Sheets, bound documents  
Original size  
Copy sizes  
Max. 10" x 14" (5-1/2" x 8-1/2" to 10" x 14" for SPF)  
3-1/2" x 5-1/2" to 8-1/2" x 14"  
(Feed copy paper lengthwise only.)  
Image loss: Max. 5/32" (4 mm) (leading and trailing edges)  
Max. 11/64" (4.5 mm) (along the other edges in  
totals)  
Copy speed  
15 copies/min.  
Continuous copying  
Max. 99 copies; subtractive counter  
9.6 s (normal copying mode)  
First-copy time  
(Approximately)  
6
Copy ratio  
Variable: 50% to 200% in 1% increments (total 151 steps)  
Fixed: 50%, 64%, 78%, 100%, 129%, 200%  
Exposure system  
Original table: Moving optical source, slit exposure (stationary  
platen) with automatic exposure  
SPF: Moving original  
Copy paper feed  
Two paper trays with automatic feed (250 sheets); one bypass  
tray with 50-sheet automatic feed capability  
Fusing system  
Development system  
Light source  
Heat rollers  
Magnetic brush development  
Xenon lamp  
Resolution  
Scan: 400 dpi  
Output: 600 dpi  
Memory  
6 MB  
36  
SPECIFICATIONS  
Power supply  
AC 120V ( 10%), 60 Hz ( 2%)  
1,000 W  
Power consumption  
Overall dimensions  
31.9" (W) x 19" (D) (809 mm (W) x 483 mm (D))  
Weight  
57.3 lbs. (26 kg)  
(Approximately)  
Toner cartridge included  
Copier dimensions  
Operating conditions  
Noise level  
20.4" (W) x 19" (D) x 18.3" (H)  
(518 mm (W) x 483mm (D) x 465 mm (H))  
Temperature: 50°F to 86°F (10°C to 30°C)  
Humidity: 20% to 85%  
Sound Power Level LWA  
Copying: 71 [dB (A)], Standby: Background noise level  
Sound Pressure Level LPA (bystander positions)  
Copying: 40 [dB (A)], Standby: Background noise level  
Noise emission measurement in accordance with ISO 7779.  
6
Optional equipment  
GDI expansion kit (AR-PG1)  
First-copy time may differ depending on operating conditions, such as power-supply voltage  
and room temperature.  
As a part of our policy of continuous improvement, SHARP reserves the right to  
make design and specification changes for product improvement without prior  
notice. The performance specification figures indicated are nominal values of  
production units.There may be some deviations from these values in individual  
units.  
37  
SUPPLIES  
Types and sizes of copy paper  
For best results, use only paper recommended by SHARP.  
Type of paper  
feeding  
Type of media  
Size  
Weight  
Paper tray  
Standard paper  
Letter (8-1/2" x 11")  
15 lbs. to 21 lbs.  
Legal (8-1/2" x 14")  
Invoice (5-1/2" x 8-1/2")  
A4 (210 mm x 297 mm)  
B5 (182 mm x 257 mm)  
A5 (148.5 mm x 210 mm)  
Bypass tray  
Standard paper and  
thick paper  
Letter (8-1/2" x 11")  
Legal (8-1/2" x 14")  
14 lbs. to 34.5  
lbs.**  
Invoice (5-1/2" x 8-1/2")  
A4 (210 mm x 297 mm)  
B5 (182 mm x 257 mm)  
A5 (148.5 mm x 210 mm)  
A6 (105 mm x 148.5 mm)  
Special Transparency Letter (8-1/2" x 11")  
media  
film  
A4 (210 mm x 297 mm)  
Envelope*  
Commercial 10  
(4-1/8" x 9-1/2")  
Monarch  
6
(3-7/8" x 7-1/2")  
International DL  
(110 mm x 220 mm)  
International C5  
(162 mm x 229 mm)  
* Do not use envelopes that have metal clasps, plastic snappers, string closures, windows,  
linings, self-adhesive, patches or synthetic materials. These will cause physical damage to  
the copier.  
** For paper weighing from 28 to 34.5 lbs., 8-1/2" x 11" is the maximum size that can be fed  
through the bypass tray.  
G
Special papers such as transparency film and labels must be fed one sheet at a time through  
the bypass tray.  
Be sure to use only genuine SHARP parts and supplies.  
For best copying results, be sure to use only SHARP Genuine Supplies which  
are designed, engineered, and tested to maximize the life and performance of  
SHARP copiers. Look for the Genuine Supplies label on the toner package.  
38  
SUPPLIES  
Proper storage  
1. Store the supplies in a location that is:  
G
clean and dry,  
G
at a stable temperature,  
G
not exposed to direct sunlight.  
2. Store copy paper in the wrapper and lying flat.  
G
Paper stored out of the wrapper or in packages standing on end may curl or get damp,  
resulting in paper misfeeds.  
6
39  
INDEX  
A
L
Auto clear . . . . . . . . . . . . . . . . . . . . 20, 21  
Automatic exposure adjustment . . . . . . . 35  
Auto power shut-off mode . . . . . . . . 20, 21  
Light key . . . . . . . . . . . . . . . . . . . . . . . . 15  
Loading copy paper . . . . . . . . . . . . . . . . 10  
M
B
Maintenance  
Bypass tray . . . . . . . . . . . . . . . . . . . . . . 17  
user maintenance . . . . . . . . . . . . . . . 25  
maintenance required indicator . . . . . 32  
Manual exposure . . . . . . . . . . . . . . . . . . 15  
Manual feeding . . . . . . . . . . . . . . . . . . . 17  
Misfeed removal  
fusing area. . . . . . . . . . . . . . . . . . . . . 28  
lower paper feed area . . . . . . . . . . . . 30  
paper feed area . . . . . . . . . . . . . . . . . 28  
SPF . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
transport area . . . . . . . . . . . . . . . . . . 29  
C
Cautions . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Cautions on handling . . . . . . . . . . . . . . . . 9  
Charger cleaner . . . . . . . . . . . . . . . . . . . 26  
Copier trouble? . . . . . . . . . . . . . . . . . . . 27  
Copying  
normal . . . . . . . . . . . . . . . . . . . . . . . . 12  
reduction/enlargement. . . . . . . . . . . . 16  
through bypass tray. . . . . . . . . . . . . . 17  
two-sided . . . . . . . . . . . . . . . . . . . . . . 18  
Copy paper . . . . . . . . . . . . . . . . . . . . . . 38  
Copy quantity. . . . . . . . . . . . . . . . . . . . . 14  
Copy ratio . . . . . . . . . . . . . . . . . . . . . . . 16  
N
Names  
operation panel. . . . . . . . . . . . . . . . . . . 7  
part . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
D
O
Dark key . . . . . . . . . . . . . . . . . . . . . . . . 15  
Developer replacement required  
indicator . . . . . . . . . . . . . . . . . . . . . . . . . 32  
Document feeder tray . . . . . . . . . . . . . . 13  
ON LINE indicator . . . . . . . . . . . . . . . . . . 7  
Operation panel  
part names . . . . . . . . . . . . . . . . . . . . . 7  
Options . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Original cover . . . . . . . . . . . . . . . . . . . . . 6  
Original guides . . . . . . . . . . . . . . . . . 6, 13  
Original table . . . . . . . . . . . . . . . . . . . 6, 13  
E
Enlargement . . . . . . . . . . . . . . . . . . . . . 16  
Exposure adjustment. . . . . . . . . . . . . . . 15  
P
F
Paper  
Features . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Fixed copy ratio . . . . . . . . . . . . . . . . . . . 16  
Fusing unit release lever . . . . . . . . . . 6, 28  
loading. . . . . . . . . . . . . . . . . . . . . . . . 10  
special . . . . . . . . . . . . . . . . . . . . . . . . 38  
specifications . . . . . . . . . . . . . . . . . . . 38  
Paper feed area . . . . . . . . . . . . . . . . . . . 28  
Paper output tray . . . . . . . . . . . . . . . . . . . 6  
Paper output tray extension . . . . . . . . 6, 12  
Paper size . . . . . . . . . . . . . . . . . . . . . . . 38  
Paper transport area . . . . . . . . . . . . . . . 29  
Paper tray . . . . . . . . . . . . . . . . . . . . . . . . 6  
Part names . . . . . . . . . . . . . . . . . . . . . . . 6  
Photo mode . . . . . . . . . . . . . . . . . . . . 7, 15  
G
GDI expansion kit (AR-PG1) . . . . . . . . . 37  
I
Installation  
location . . . . . . . . . . . . . . . . . . . . . . . . . 8  
INDEX  
Power on . . . . . . . . . . . . . . . . . . . . . . . . 12  
Power save modes . . . . . . . . . . . . . 20, 21  
Power switch . . . . . . . . . . . . . . . . . . . 6, 12  
Preheat mode . . . . . . . . . . . . . . . . . 20, 21  
Print key . . . . . . . . . . . . . . . . . . . . . . . . 14  
T
Toner cartridge  
– indicator. . . . . . . . . . . . . . . . . . . . . 7, 34  
– life . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
– replacement. . . . . . . . . . . . . . . . . . . . 23  
Toner save mode . . . . . . . . . . . . . . . . . . 20  
Total number of copies. . . . . . . . . . . . . . 22  
Transfer charger. . . . . . . . . . . . . . . . . 6, 26  
Troubleshooting . . . . . . . . . . . . . . . . . . . 33  
Two-sided copying . . . . . . . . . . . . . . . . . 18  
R
Ready indicator . . . . . . . . . . . . . . . . . . . . 7  
Reduction . . . . . . . . . . . . . . . . . . . . . . . 16  
Replacement  
– toner cartridge . . . . . . . . . . . . . . . . . . 23  
U
S
User maintenance  
Single pass feeder (SPF) . . . . . . . . . . . 13  
Special paper. . . . . . . . . . . . . . . . . . . . . 38  
Specifications  
– copier . . . . . . . . . . . . . . . . . . . . . . . . 36  
– paper . . . . . . . . . . . . . . . . . . . . . . . . . 38  
SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Status indicators . . . . . . . . . . . . . . . . . . 34  
Storage of supply. . . . . . . . . . . . . . . . . . 39  
Stream feeding mode . . . . . . . . . . . 15, 21  
– cabinet. . . . . . . . . . . . . . . . . . . . . . . . 25  
– original cover . . . . . . . . . . . . . . . . . . . 25  
– original table . . . . . . . . . . . . . . . . . . . 25  
– transfer charger . . . . . . . . . . . . . . . . . 26  
Z
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Date Issued:Nov. 1, 2000  
MSDS No. F-01001  
MATERIAL SAFETY DATA SHEET  
Section 1.  
Product Identification  
Product:  
AR-152NT/T/FT/ST (Black Toner)  
Section 2.  
Suppliers Name and Address  
Sharp Corporation  
22-22 Nagaike-cho, Abeno-ku, Osaka, Japan  
Local suppliers are listed below. Please contact the nearest supplier for additional information.  
(Country)  
U.S.A.  
(Name and Telephone Number)  
Sharp Electronics Corporation  
Telephone number for information: 1-800-237-4277  
Emergency telephone number:  
1-800-255-3924  
Canada  
Sharp Electronics of Canada Ltd.  
Telephone number for information: 905-890-2100  
Emergency telephone number:  
1-800-255-3924  
United Kingdom  
Sharp Electronics (U.K.) Ltd.  
Telephone number for information: 01923-474013  
Section 3.  
Ingredients  
Ingredients  
CAS No.  
Proportion OSHA PEL ACGIHTLV Other Limits  
Styrene-Acrylate copolymer  
Carbon black  
29497-14-1  
1333-86-4  
> 88 %  
< 6.0%  
< 4.5%  
< 1.5%  
Not listed  
3.5mg/m3  
Not listed  
0.5mg/m3  
Not listed  
3.5mg/m3  
Not listed  
0.5mg/m3  
None  
None  
None  
None  
Iron oxide  
1309-38-2  
Metal Complex dye  
109125-51-1  
109125-50-0  
84179-66-8  
{
Section 4.  
Hazardous Identification (Emergency Overview)  
Toner is a fine, black powder possessing no immediate hazard. There are no anticipated carcinogenic  
effects from exposure based on animal tests performed using toner.When used as intended according  
to instructions, studies do not indicate any symptoms of fibrosis will occur.  
Section 5.  
Health Hazard Data  
Route(s) of Entry:  
Inhalation?  
Skin?  
No  
Ingestion?  
Possible but very unusual.  
Yes  
Health Hazards: Acute oral toxicity ------------- LDLo of this toner is over 2,000mg/kg.  
Mutagenicity -------------------- The result of Ames test is negative.  
Carcinogenicity: In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible  
human carcinogen). This classification is given to chemicals for which there is  
inadequate human evidence, but sufficient animal evidence on which to base an  
opinion of carcinogenicity.The classification is based upon the development of lung  
tumors in rats receiving chronic inhalation exposures to free carbon black at levels  
that induce particle overload of the lung. Studies performed in animal models other  
than rats did not show any association between carbon black and lung tumors.  
Moreover, a two-year cancer bioassay using a typical toner preparation containing  
carbon black demonstrated no association between toner exposure and tumor  
development in rats.  
Chronic Effect: In a study in rats of chronic inhalation exposure to a typical toner, a mild to moderate  
degree of lung fibrosis was observed in 92% of the rats in the high concentration  
(16mg/m3) exposure group, and a minimal to mild degree of fibrosis was noted in  
22% of the animals in the middle (4mg/m3) exposure group, but no pulmonary change  
was reported in the lowest (1mg/m3) exposure group, the most relevant level to  
potential human exposures.  
Signs and Symptoms of Exposure: Minimal irritation to respiratory tract may occur as with exposure  
to any non-toxic dust.  
Medical Conditions Generally Aggravated by Exposure: None  
Emergency and First Aid Procedures:  
Inhalation; Remove to fresh air. If effects occur, consult medical personnel.  
Eye;  
In case of contact, immediately flush eyes with water for 15 minutes.  
Section 6.  
Physical Chemical Characteristics  
Boiling / Melting Point: Not applicable  
Specific Gravity:  
1.1  
Vapor Pressure:  
Vapor Density:  
Evaporation Rate:  
Appearance:  
Odor:  
Not applicable  
Not applicable  
Not applicable  
Fine powder  
Odorless  
Solubility in Water: Negligible  
PH:  
Not applicable  
Viscosity:  
Color:  
Not applicable  
Black  
Section 7.  
Fire and Explosion Data  
Flash Point (Method Used):  
Ignition Temperature:  
Not applicable  
>350°C  
Flammable Limits:  
(LEL); Not applicable  
(UEL); Not applicable  
Extinguishing Media:  
Special Fire Fighting Procedure:  
CO2, dry chemical, foam or water  
None  
Unusual Fire and Explosion Hazard: This material has no unusual fire or explosion hazards.  
Sensitivity to Mechanical Impact:  
Sensitivity to Static Charge:  
None  
None  
Section 8.  
Reactivity Data  
Stability:  
Stable  
Incompatibility (Material to Avoid): None  
Hazardous Decomposition:  
Hazardous Polymerization:  
CO and NOx  
Will not occur.  
Section 9.  
Precautions for Safe Handling and Use  
Personal Protection Information (Respiratory, Eye Protection and Protective Glove):  
Use of a dust mask is recommended when handling a large quantity of toner or  
during long term exposure, as with any non-toxic dust.  
Engineering Control / Ventilation:  
Work / Hygienic Practice:  
Not required.  
Inhalation should be minimized as with any non-toxic  
dust.  
Steps to be taken in case of Spill or Leak: Sweep up or clean up with vacuum cleaner.  
Waste Disposal Method:  
Waste material may be dumped or incinerated under  
conditions which meet all federal, state and local  
environmental regulations.  
Section 10. Regulatory Information  
NFPA Rating (U.S.A.):  
WHMIS Legislation (Canada):  
Transport Information:  
UN No.:  
Health = 1  
Flammability = 1  
This product is not a controlled product.  
This product is not a hazardous material.  
None allocated.  
Reactivity = 0  
Section 11. Other Information  
References: IARC (1996) IARC Monographs on the Evaluation of the Carcinogenic Risk of Chemicals  
to Humans, Vol. 65, Printing Process and Printing inks, Carbon Black and Some Nitro  
Compounds, Lyon, pp-149-261  
H. Muhle, B. Bellmann, O. Creutzenberg, C. Dasenbrock, H. Ernst, R. Kilpper, J. C.  
MacKenzie, P. Morrow, U. Mohr, S. Takenaka, and R. Mermelstein (1991) Pulmonary  
Response toToner upon Chronic Inhalation Exposure in Rats. Fundamental and Applied  
Toxicology 17, pp. 280-299  
Date Issued :Nov. 1, 2000  
MSDS No. F-31001  
MATERIAL SAFETY DATA SHEET  
Section 1.  
Product Identification  
Product  
AR-152ND/DV/SD (Black Developer)  
Section 2.  
Suppliers Name and Address  
Sharp Corporation  
22-22 Nagaike-cho, Abeno-ku, Osaka, Japan  
Local suppliers are listed below. Please contact the nearest supplier for additional information.  
(Country)  
U.S.A.  
(Name and Telephone Number)  
Sharp Electronics Corporation  
Telephone number for information: 1-800-237-4277  
Emergency telephone number:  
1-800-255-3924  
Canada  
Sharp Electronics of Canada Ltd.  
Telephone number for information: 905-890-2100  
Emergency telephone number:  
1-800-255-3924  
United Kingdom  
Sharp Electronics (U.K.) Ltd.  
Telephone number for information: 01923-474013  
Section 3.  
Ingredients  
Ingredients  
CAS No.  
Proportion OSHA PEL ACGIHTLV Other Limits  
Iron powder  
Styrene-Acrylate copolymer  
Carbon black  
7439-89-6  
29497-14-1  
1333-86-4  
> 92.5%  
< 7.0%  
< 0.5%  
Not listed  
Not listed  
3.5mg/m3  
Not listed  
Not listed  
3.5mg/m3  
None  
None  
None  
Section 4.  
Hazardous Identification (Emergency Overview)  
Developer is a black powder containing small amounts of toner, and possessing no immediate hazard.  
There are no anticipated carcinogenic effects from exposure based on animal tests performed using  
toner.  
Section 5.  
Health Hazard Data  
Route(s) of Entry:  
Inhalation?  
Skin?  
Ingestion?  
No  
No  
Possible but very unusual.  
Health Hazards: Acute oral toxicity ------------- LDLo of this toner which is included in this developer  
is over 2,000mg/kg.  
Mutagenicity -------------------- The toner, which is included in this developer, has been  
tested on Ames test. The result is negative.  
Carcinogenicity: In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible  
human carcinogen). This classification is given to chemicals for which there is  
inadequate human evidence, but sufficient animal evidence on which to base an  
opinion of carcinogenicity.The classification is based upon the development of lung  
tumors in rats receiving chronic inhalation exposures to free carbon black at levels  
that induce particle overload of the lung. Studies performed in animal models other  
than rats did not show any association between carbon black and lung tumors.  
While there have been no studies to date using developer, a two-year cancer  
bioassay using a typical toner preparation containing carbon black (a small amount  
of toner is included in the developer mixture) demonstrated no association between  
toner exposure and tumor development in rats.  
Signs and Symptoms of Exposure: Minimal irritation to respiratory tract may occur as with exposure  
to any non-toxic dust.  
Medical Conditions Generally Aggravated by Exposure: None  
Emergency and First Aid Procedures:  
Inhalation; Remove to fresh air. If effects occur, consult medical personnel.  
Eye;  
In case of contact, immediately flush eyes with water for 15 minutes.  
Section 6.  
Physical Chemical Characteristics  
Boiling / Melting Point: Not applicable  
Specific Gravity:  
about 7.3  
Vapor Pressure:  
Vapor Density:  
Evaporation Rate:  
Appearance:  
Odor:  
Not applicable  
Not applicable  
Not applicable  
Fine powder  
Odorless  
Solubility in Water: Negligible  
PH:  
Not applicable  
Viscosity:  
Color:  
Not applicable  
Black  
Section 7.  
Fire and Explosion Data  
Flash Point (Method Used):  
Ignition Temperature:  
Not applicable  
>350°C  
Flammable Limits:  
(LEL); Not applicable  
(UEL); Not applicable  
Extinguishing Media:  
Special Fire Fighting Procedure:  
CO2, dry chemical, foam or water  
None  
Unusual Fire and Explosion Hazard: This material has no unusual fire or explosion hazards.  
Sensitivity to Mechanical Impact:  
Sensitivity to Static Charge:  
None  
None  
Section 8.  
Reactivity Data  
Stability:  
Stable  
Incompatibility (Material to Avoid): None  
Hazardous Decomposition:  
Hazardous Polymerization:  
CO and NOx  
Will not occur.  
Section 9.  
Precautions for Safe Handling and Use  
Personal Protection Information (Respiratory, Eye Protection and Protective Glove):  
None required under normal use.  
Engineering Control / Ventilation:  
Work / Hygienic Practice:  
Not required.  
Not required.  
Steps to be taken in case of Spill or Leak: Sweep up or clean up with vacuum cleaner.  
Waste Disposal Method:  
Waste material may be dumped or incinerated under  
conditions which meet all federal, state and local  
environmental regulations.  
Section 10. Regulatory Information  
NFPA Rating (U.S.A.):  
WHMIS Legislation (Canada):  
Transport Information:  
UN No.:  
Health = 1  
Flammability = 1  
This product is not a controlled product.  
This product is not a hazardous material.  
None allocated.  
Reactivity = 0  
Section 11. Other Information  
References: IARC (1996) IARC Monographs on the Evaluation of the Carcinogenic Risk of Chemicals  
to Humans, Vol. 65, Printing Process and Printing inks, Carbon Black and Some Nitro  
Compounds, Lyon, pp-149-261  
H. Muhle, B. Bellmann, O. Creutzenberg, C. Dasenbrock, H. Ernst, R. Kilpper, J. C.  
MacKenzie, P. Morrow, U. Mohr, S. Takenaka, and R. Mermelstein (1991) Pulmonary  
Response toToner upon Chronic Inhalation Exposure in Rats.Fundamental and Applied  
Toxicology 17, pp. 280-299  
MEMO  
MEMO  
MEMO  
This device complies with Part 15 of the FCC rules. Operation is subject to the  
following two conditions: (1) This device may not cause harmful interference, and (2)  
this device must accept any interference received, including interference that may  
cause undesired operation.  
WARNING:  
FCC Regulations state that any unauthorized changes or modifications to this  
equipment not expressly approved by the manufacturer could void the user’s authority  
to operate this equipment.  
Note:  
This equipment has been tested and found to comply with the limits for a Class B  
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference in a residential installation.  
This equipment generates, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful  
interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television  
reception, which can be determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the following  
measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
NOTICE  
BE SURETO ASKYOUR AUTHORIZED SHARP DEALER ABOUTTHEWARRANTYTHAT  
YOUR SELLING DEALER EXTENDS TO YOU. In order to assure you, the end-user, of  
warranty protection, Sharp extends a limited warranty to each of its authorized dealers  
and, in turn, requires each of its authorized dealers to extend its own warranty to you on  
terms that are no less favorable than those given to the dealer by Sharp. You should be  
aware, however, that Sharp does not itself extend any warranties, either express or implied,  
directly to you, the end-user, and no one is authorized to make any representations or  
warranties on behalf of Sharp. Specifically, SHARP DOES NOT EXTEND TO YOU, THE  
END-USER, ANY EXPRESS WARRANTY OR ANY IMPLIED WARRANTY OF  
MERCHANTABILITY, FITNESS FOR USE OR FITNESS FOR ANY PARTICULAR  
PURPOSE IN CONNECTION WITH THE HARDWARE, SOFTWARE OR FIRMWARE  
EMBODIED IN, OR USED IN CONJUNCTION WITH THIS PRODUCT. Sharp is not  
responsible for any damages or loss, either direct, incidental or consequential, which you,  
the end-user, may experience as a result of your purchase or use of the hardware, software  
or firmware embodied in or used in conjunction with this Product.Your sole remedy, in the  
event that you encounter any difficulties with this Product, is against the authorized dealer  
from which you purchased the Product.  
AR-F152 Digital Laser Copier/Facsimile  
In the event that this authorized dealer does not honor its warranty commitments, please  
contact the General Manager, Business Products Group, Sharp Electronics Corporation, Sharp  
Plaza, Mahwah, NJ 07430-2135, so that Sharp can try to help assure complete satisfaction  
of all the warranty rights to which you are entitled from the authorized dealer.  
AR-F152  
SHARP ELECTRONICS CORPORATION  
Sharp Plaza, Mahwah, New Jersey 07430-2135.  
SHARP CORPORATION  
PRINTED IN CHINA  
2000M  
KS  
TINSE0465QSZZ  

Lanier 5813 User Manual
Milwaukee Tools Battery Charger 48 59 0231 User Manual
Ricoh Aficio Is 2416l User Manual
Samsung Am27a1c13 User Manual
Sanyo 24ks62r User Manual
Sanyo Twicell Hr 4u User Manual
Universal Electronics 3 Stage Switch Mode Fan Cooled Charger 24bc5000tfg 1 User Manual
Whirlpool Acm122 User Manual
Xerox Dcc250 User Manual
Xerox Faxcentre 2218 User Manual