Intelligent
Battery Manager
SI263 Instructions
Read and save these instructions.
SI263 IM 0205v1.indd
1
3/2/05 4:41:02 PM
Table of Contents
Important Safety Precautions .....................................................5
Warnings ...................................................................................6
Personal Safety Precautions........................................................9
Charging Preparation ...............................................................10
Features...................................................................................11
Extension Cord Use .................................................................12
Battery Preparation..................................................................13
Operation................................................................................14
Charging Battery in the Vehicle ............................................14
Negative-Grounded System (Standard).................................16
Positive-Grounded System ...................................................17
Charging a Removed Battery................................................18
Operating Features ..................................................................20
Charge Rate.........................................................................20
Battery Type Button..............................................................21
General Notes......................................................................22
Charging Tips.......................................................................23
SI263 IM 0205v1.indd
3
3/2/05 4:41:06 PM
Table of Contents
Maintenance and Care ............................................................24
Troubleshooting .......................................................................25
Statement of FCC Compliance.................................................30
FCC Label Compliance Statement............................................31
SI263 IM 0205v1.indd
4
3/2/05 4:41:06 PM
Important Safety Precautions
WARNING - RISK OF EXPLOSIVE GASES
WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS
DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES
DURING NORMAL OPERATION. FOR THIS REASON, IT IS
IMPORTANT TO ALWAYS READ THIS MANUAL BEFORE USING
THE INTELLIGENT BATTERY MANAGER AND FOLLOW THE
INSTRUCTIONS EXACTLY.
To reduce risk of battery explosion, follow these instructions and
those published by battery manufacturer and the manufacturer
of any equipment you intend to use in the vicinity of the bat-
tery. Review cautionary markings on these products and on the
engine.
SAVE THESE INSTRUCTIONS — This manual contains important
safety and operating instructions.
5
SI263 IM 0205v1.indd
5
3/2/05 4:41:06 PM
Warnings
•Read all instructions and cautions printed on the Battery
Manager, battery and vehicle, or equipment using a battery.
•Use the Battery Manager only on lead-acid type rechargeable
batteries, such as those typically used in cars, trucks, tractors,
airplanes, vans, RV’s, trolling motors, etc. The Battery Manager
is not intended to supply power to a low-voltage electrical
system other than in an automotive application.
•Never use the Battery Manager for charging dry cell batteries
that are commonly used in home appliances such as radios,
stereos, remote controls, etc. These batteries may explode
and cause personal injury.
•Do not disassemble the Battery Manager. If service or repair is
required, take the Battery Manager to a qualified service profes-
sional. Incorrect assembly may result in fire or electrical shock.
•To reduce risk of electrical shock, unplug the Battery Manager
from the outlet before attempting any maintenance or cleaning.
•Always charge batteries in a well-ventilated area. The Battery
Manager produces heat during operation and requires proper
ventilation. Air-flow is required around the entire unit.
6
SI263 IM 0205v1.indd
6
3/2/05 4:41:07 PM
Warnings
•Do not set the Battery Manager on flammable materials such
as carpeting, upholstery, paper, cardboard, etc. It may damage
leather, plastic and rubber.
•Place the Battery Manager as far away from the battery being
charged as cables permit.
•Do not expose the Battery Manager to rain or snow.
•Never charge a frozen battery. If battery fluid (electrolyte)
becomes frozen, bring the battery into a warm area and allow
it to thaw before charging begins.
•Never allow battery acid to drip on the Battery Manager when
checking the battery.
•Never set a battery on top of the Battery Manager.
•Never place the Battery Manager directly above the battery
being charged. The gases from the battery will corrode and
damage the Battery Manager.
•Never touch the battery clamps together when the Battery Man-
ager is on. This could cause a spark.
7
SI263 IM 0205v1.indd
7
3/2/05 4:41:07 PM
Warnings
•Never operate the Battery Manager if it has received a hard
blow, been dropped or otherwise damaged. Take it to a quali-
fied service professional for inspection and repair.
•Be sure to position the Battery Manager power cord to prevent
it from being stepped on, tripped over or damaged.
•When unplugging the Battery Manager, never pull out the plug
by the cord. Pulling on the cord may cause damage to the cord
or the plug.
•Do not operate the Battery Manager if it has a damaged power
cord or plug. Replace the cord.
8
SI263 IM 0205v1.indd
8
3/2/05 4:41:07 PM
Personal Safety Precautions
•Wear complete eye and clothing protection when working
with lead-acid batteries.
•Ensure someone is within range of your voice in case aid is
needed while working with or near a lead-acid battery.
•Always have plenty of fresh water and soap nearby in case
battery acid gets in your eyes, or on your skin or clothing. If
this occurs, wash with soap and water immediately and get
medical attention.
•When working with a battery, avoid touching your eyes. Acid
particles (corrosion) may get into your eyes. If this occurs, flush
eyes immediately with running cold water for at least 10 min-
utes and get medical attention.
•Remove all personal metal items from your body, such as rings,
bracelets, necklaces and watches, while working with a lead-
acid battery. A battery can produce a short-circuit current high
enough to weld a ring (or similar object) to metal, causing a
severe burn.
9
SI263 IM 0205v1.indd
9
3/2/05 4:41:07 PM
Personal Safety Precautions
•Do not drop any metal tool or metal object onto the battery.
This may result in a spark or short circuit across the battery or
another electrical device that may cause an explosion.
•Always operate the Battery Manager in an open, well-ventilated
area.
•Never smoke or allow a spark or flame in the vicinity of the
battery or engine. Batteries generate explosive gases.
•Before attempting to clean up a battery, neutralize any acid
spills thoroughly with baking soda.
Charging Preparation
Power
The Battery Manager requires a three-prong grounded 120V AC
outlet that meets all local codes and ordinances.
Grounding Pin
Grounding Outlet
10
SI263 IM 0205v1.indd 10
3/2/05 4:41:07 PM
Features
•Charges 6- and 12-volt lead-acid and AGM batteries of all sizes.
•Automatically adjusts charging rate to match battery requirements.
•“Intelligent” microprocessor-controlled circuitry monitors and
self-adjusts to protect batteries from any damage.
•Safely maintains batteries in motorcycles, snowmobiles and
lawn tractors while in long-term storage or between uses.
•Easy-to-read LED indicators display battery charge status.
•Automatic overload and short-circuit protection.
•Electronic push-button controls for selecting charge rate and
battery type.
•Wall-mountable, high-impact, corrosion-resistant molded case.
•2 amp Maintenance Charge.
•4 amp Slow Charge.
•6 amp Rapid Charge.
11
SI263 IM 0205v1.indd 11
3/2/05 4:41:07 PM
Extension Cord Use
The use of an extension cord is not recommended. If you must
use an extension cord, please follow these guidelines:
•Ensure the pins on the extension cord plug match the Battery
Manager’s plug exactly (e.g. same number, size, shape, etc.).
•Ensure the extension cord is properly wired and is in good
electrical condition.
•Ensure the wire length and gauge correspond to the AC
ampere rating, as specified in the chart below:
Extension Cord (Minimum Recommended)
Length of Cord (Feet)
AWG* Size of Cord
25
18
50
16
100 150
12 10
*AWG=American Wire Gauge
12
SI263 IM 0205v1.indd 12
3/2/05 4:41:07 PM
Battery Preparation
While preparing to charge a battery, read and follow these
guidelines:
1. Ensure you’re working with a 12- or 6-volt lead-acid battery.
To determine the voltage of the battery, refer to the vehicle
owner’s manual or the battery markings. Set the Battery
Manager to the 6V or 12V mode accordingly.
2. Clean the battery terminals. Be careful to keep corrosion from
getting in or around your eyes.
3. Wear safety glasses. (See “Personal Safety Precautions” section
this manual.)
4. Read all of the battery manufacturer’s specific precautions, for
example, removing or not removing vent caps while charging
and recommended rates of charge.
5. To add water to batteries with removable vent caps, carefully
pour distilled water into each cell until battery acid reaches
the level recommended by the manufacturer. This helps purge
excessive gases from the cells. Do not overfill. If the battery is
sealed, with non-removable vent caps, no action is necessary.
13
SI263 IM 0205v1.indd 13
3/2/05 4:41:07 PM
Battery Preparation
6. Ensure the area around the battery is well ventilated. Gas can
be blown away using a piece of cardboard, or other nonme-
tallic material, as a fan.
7. If it is necessary to remove the battery from the vehicle before
charging, always remove the grounded terminal from the
battery first. Switch off all vehicle accessories to avoid sparks
from occurring.
Note: A marine battery installed in a boat must be removed and
charged on shore.
Operation
Charging Battery in the Vehicle
1. To avoid personal injury, stand clear of all fan blades, belts,
pulleys and other engine parts.
2. To avoid damaging the Battery Manager, keep the power
cord and output cords away from the hood, door and moving
engine parts.
14
SI263 IM 0205v1.indd 14
3/2/05 4:41:07 PM
Charging Battery in the Vehicle
3. To determine the polarity of the battery posts, check the iden-
tification marks on the battery: POSITIVE (POS, P or +) and
NEGATIVE (NEG, N or -). The positive post is usually marked
red and is larger than the negative post.
4. Identify which battery post is grounded or connected to the
chassis. THIS IS NORMALLY THE NEGATIVE POST.
15
SI263 IM 0205v1.indd 15
3/2/05 4:41:08 PM
Negative-Grounded System (Standard)
1. To connect to a negative-grounded system, attach the red
POSITIVE output clamp to the POSITIVE post of the battery.
Twist the clamp back and forth to ensure a solid electrical
connection is made.
2. Connect the black NEGATIVE output clamp to a heavy, un-
painted metal part of the chassis or engine block, away from
the battery. (See illustration.) DO NOT connect the clamp to
the negative battery post, carburetor, fuel line or sheet metal
part.
3. Plug the power cord into an AC outlet.
4. To select the desired charge rate and battery voltage, press
the appropriate CONTROL BUTTONS: The CHARGING
(yellow) LED illuminates when the charging process begins.
If the CHECK (red) LED illuminates, ensure correct cable
connections.
5. To disconnect the Battery Manager, unplug its power cord
before disconnecting the output clamps. While standing away
from the battery, remove the output clamp from the chassis
or engine block. Finally, remove the output clamp from the
battery post.
16
SI263 IM 0205v1.indd 16
3/2/05 4:41:08 PM
Negative-Grounded System (Standard)
6. Clean and store the Battery Manager in a dry location.
Positive-Grounded System
1. To connect to a positive-grounded system, attach the black
NEGATIVE output clamp to the NEGATIVE post of the
battery. Twist the clamp back and forth to ensure a solid
electrical connection is made.
2. Connect the red POSITIVE output clamp to a heavy, unpaint-
ed metal part of the chassis or engine block, away from the
battery. DO NOT connect to the positive battery post, carbu-
retor, and fuel line or sheet metal part.
POSITIVE
NEGATIVE
HARGER
BAT
POWER
CORD
TO
GROUNDED
POWER
OUTLET
17
SI263 IM 0205v1.indd 17
3/2/05 4:41:08 PM
Charging a Removed Battery
1. To charge a battery that has been removed from the vehicle,
check the polarity identification marks on the battery post:
POSITIVE (POS, P or +) and NEGATIVE (NEG, N or -). The
positive post is usually marked red and is larger than the
negative post.
2. Attach a 24-inch-long (at least), 6-gauge (AWG), insulated
battery cable to the NEGATIVE (NEG, N or -) battery post.
Twist the clamp back and forth to ensure a solid electrical
connection is made.
3. Connect the POSITIVE (red) output clamp to the POSITIVE
battery post. Twist the clamp back and forth to be sure a
solid electrical connection is made.
4. Position yourself as far away from the battery as possible and
connect the NEGATIVE (black) output clamp to the free end
of the cable.
5. Plug the power cord into an AC outlet.
18
SI263 IM 0205v1.indd 18
3/2/05 4:41:08 PM
Charging a Removed Battery
6. To select the desired charge rate and battery voltage, press
the appropriate CONTROL BUTTONS. The CHARGING
(yellow) LED illuminates when the charging process begins.
If the CHECK (red) LED illuminates, check for correct cable
connections.
7. To disconnect the Battery Manager, unplug its power cord
before attempting to disconnect the Battery Manager clamps.
While standing away from the battery, remove the output
clamp from the NEGATIVE battery post. Finally, remove the
output clamp from the POSITIVE battery post.
8. Clean and store the Battery Manager in a dry location.
19
SI263 IM 0205v1.indd 19
3/2/05 4:41:08 PM
Operating Features
Charge Rate
Control Panel
To set the charge rate to one of the following three selections,
press the CHARGE RATE button.
•2A or 4A CHARGE RATE: Intended for charging small batteries
such as those commonly used in garden tractors, snowmobiles
and motorcycles.
Note: The 2A rate is not intended for use as a trickle charge for
larger batteries.
•6A CHARGE RATE: For charging automotive and marine batter-
ies. Not intended for industrial applications.
20
SI263 IM 0205v1.indd 20
3/2/05 4:41:08 PM
Battery Type Button
To set battery type to one of the following two selections, press
the BATTERY TYPE button.
•12 Volt: Battery typically used in cars, trucks and motorcycles.
These batteries usually have vent caps and are often marked
“low maintenance” or “maintenance-free.”
•6 Volt: Battery typically used in antique and some specialized
vehicles.
Automatic Shut Off: When the 2A, 4A or 6A charge rate is
selected, the Battery Manager is set to perform an automatic
charge. The charging process stops automatically after the battery
is charged.
Aborted Charge: If the charging process cannot be completed
normally, charging is aborted. The Battery Manager’s output is
shut off and the CHECK (red) LED blinks. In this state, the Bat-
tery Manager’s buttons are inoperative. To reset after an aborted
charge, unplug the Battery Manager and plug it in again.
Charging Complete: The CHARGED (green) LED illuminates
when charging is complete. The Battery Manager stops charging
and switches automatically to Maintain Mode.
21
SI263 IM 0205v1.indd 21
3/2/05 4:41:08 PM
Battery Type Button
Maintain Mode: When the CHARGED (green) LED is illumi-
nated, the Battery Manager switches automatically to Maintain
Mode. The Battery Manager monitors battery voltage. When the
voltage drops to a predetermined level, the Battery Manager will
re-initiate a charge cycle at the 2A rate.
General Notes
•If the Battery Manager does not detect a proper connection
to the battery, the CHECK (red) LED illuminates continuously
until the battery is detected. Charging will not begin while the
CHECK LED is on. When charging begins, the CHARGING
(yellow) LED illuminates.
•If the charge mode is changed after charging has started (by
pressing the CHARGE RATE or BATTERY TYPE button), the
charging process restarts at that point.
•The Battery Manager is equipped with a relay. This device
switches on and off the charge current to the battery. It is
normal to hear an occasional clicking sound when the relay
switches on or off.
22
SI263 IM 0205v1.indd 22
3/2/05 4:41:08 PM
Charging Tips
Read the entire manual before using the Battery Manager. The
tips below serve only as a guide for specific situations.
Reviving a Battery: To charge your battery enough to start your
vehicle, it is not necessary to wait for the entire charging process to
be completed. When the battery status displays 3 yellow LEDs, the
battery is usually charged enough for the vehicle to start normally.
Completing an Interrupted Charge: If the charging process has
been interrupted and restarted after the Battery Manager displays
a battery status of 4 yellow LEDs, the Battery Manager may enter
Maintain Mode. However, if the original charge was started using
the 6A rate, the charge can often be completed using the 2A rate.
23
SI263 IM 0205v1.indd 23
3/2/05 4:41:08 PM
Maintenence and Care
•To keep the Battery Manager working properly, clean the
clamps each time you are finished charging. Wipe off any
battery fluid that may have come in contact with the clamps
to prevent corrosion.
•When storing the Battery Manager, coil the input and output
cords neatly. This helps prevent accidental damage to the cords
and the Battery Manager.
•Clean the case of the Battery Manager with a soft cloth to main-
tain its shiny finish and help prevent corrosion.
•Store the Battery Manager in a clean, dry location.
24
SI263 IM 0205v1.indd 24
3/2/05 4:41:08 PM
Troubleshooting
Performance problems can often be corrected by the user. Please
review the following chart completely for possible solutions to
common problems:
PROBLEM
POSSIBLE CAUSE
SOLUTION
The CHECK
(red) LED is
illuminated.
The battery is
not connected
correctly.
Connect or adjust
clips. Check for
correct polarity.
The CHARGE RATE Press the button to
and CHARGE TYPE select the correct
buttons are not
selected.
rate and type.
The battery voltage Replace the
is less than one volt. battery or try using
a manual charger
to bring above 1V.
25
SI263 IM 0205v1.indd 25
3/2/05 4:41:09 PM
Troubleshooting
PROBLEM
POSSIBLE CAUSE
SOLUTION
LED indicators
illuminate in an
A button may have Make sure noth-
been pressed while ing is touching the
erratic manner not the Battery Manager control panel, then
explained in the
“Operating Fea-
tures” section.
was plugged in.
unplug the unit
and plug it in again.
The Battery
Manager may be
defective.
Return to place
of purchase for
replacement.
The CHECK (red)
LED is flashing.
Battery Manager
is in abort mode.
Battery may be
defective.
See “Operating
Features.”
Battery type may
Unplug the Battery
have been set for 6 Manager and select
volts on a 12-volt
battery.
the correct battery
voltage.
26
SI263 IM 0205v1.indd 26
3/2/05 4:41:09 PM
Troubleshooting
PROBLEM
POSSIBLE CAUSE
SOLUTION
The CHECK
This happens if the
battery does not
reach full charge
within 24 hours.
May be due to a
very large battery
or a bank of batter-
ies requiring more
power than the
Battery Manager
can deliver in 24
hours. The battery
may also be
Reset the Battery
Manager by unplug-
ging it. Select the
desired charge rate
and battery type
(red) LED always
flashes before the
battery is com-
pletely charged.
again, if necessary.
defective.
27
SI263 IM 0205v1.indd 27
3/2/05 4:41:09 PM
Troubleshooting
PROBLEM
POSSIBLE CAUSE
SOLUTION
The green
The battery may
be fully charged or
recently charged,
leaving the battery
If the battery is in
a vehicle, turn the
headlights on for
a few minutes to
CHARGED LED
switches on a
few minutes after
connecting to the
battery.
voltage high enough reduce the bat-
to appear to be fully tery voltage and try
charged.
charging again. Also
try a lower CHARGE
RATE selection.
The Battery Man-
ager is making an
audible clicking
sound.
The Battery Man-
No problem. This is
ager has a relay that a normal condition.
switches the current
to the battery on
and off.
28
SI263 IM 0205v1.indd 28
3/2/05 4:41:09 PM
Troubleshooting
PROBLEM
POSSIBLE CAUSE
SOLUTION
The measured
current is much
lower than was
selected.
The Battery Man-
ager reached the
maximum voltage
and is reducing the
current.
No problem. This is
a normal condition.
29
SI263 IM 0205v1.indd 29
3/2/05 4:41:09 PM
Statement of FCC Compliance
WARNING: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protec-
tion against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency en-
ergy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
30
SI263 IM 0205v1.indd 30
3/2/05 4:41:09 PM
Statement of FCC Compliance
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for
assistance.
FCC Label Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
31
SI263 IM 0205v1.indd 31
3/2/05 4:41:09 PM
WARRANTY
What Is Covered
This warranty covers any defects in materials or workmanship, with the exceptions stated below.
How Long Coverage Lasts
This warranty runs for 90 days from the date of original purchase.
What Is Not Covered
This warranty does not cover damage caused by misuse or use other than as intended and described
in the product instruction manual, or loss or damage to batteries or removable parts.
What The Sharper Image Will Do
The Sharper Image will repair any defects in materials or workmanship. In the event repair is not
possible, The Sharper Image will either replace this product with one of similar features and price,
or refund the full purchase price of the product, whichever you prefer.
How to Obtain Service
Return the product and receipt, along with a brief explanation of the problem, to:
T.S.I. - Returns Department
2901-A West 60th Street
Little Rock, AR 72209
If you have questions please feel free to contact our customer service representatives at 1-800-344-5555
or by email at [email protected].
This warranty gives you specific legal rights, and you may have other legal rights that vary from state to state.
© 2005 Sharper Image Corporation
Sharper Image Corporation
650 Davis St., San Francisco, CA 94111
(415) 445-6000
Shop online:
Due to continuing improvements, actual product may differ slightly from the product described herein.
V1 02/05
SI263 IM 0205v1.indd 32
3/2/05 4:41:09 PM
|