Samsung Mh035fpea User Manual

USER’S MANUAL

MH020FPEA

MH023FPEA

MH026FPEA

MH035FPEA

MH052FPEA1

Free Joint Multi Air Conditioner

(Cooling and Heating)

E S F I P D G R DB98-20234A(8)

Safety Precautions

The following safety precautions must be taken when using your air conditioner.

Risk of electric shock. • Can cause injury or death. • Disconnect all

WARNING

remote electric power supplies before servicing, installing or cleaning.

• This must be done by the manufacturer or its service agent or a similar

qualified person in order to avoid a hazard.

◆ Users of this product are cautioned not to attempt repair of this product

DURING OPERATION

at their own discretion. Instead, they are requested to directly contact a

designated service center or the outlet at which the product was

purchased.

◆ Never spill any kind of liquid into the unit. Should this happen, unplug

or main switch off the unit and contact an authorized service center.

◆ Do not insert anything between the air outlet blades because the inner

fan may be damaged and could cause injury. Keep children away from

the unit.

◆ Do not place any obstacles in front of the unit.

◆ Do not spray liquid of any kind into the indoor unit. Should this happen,

switch off the breaker used for your air conditioner and contact your

installation specialist.

◆ Make sure that the unit is correctly ventilated at all times:

Do not place clothing or other materials over it.

◆ If the wireless remote control will not be used for a long time, remove

the batteries. (If applicable)

◆ When using a wireless remote control, the distance should not be more

than 7 meters from the air conditioner. (If applicable)

◆ Before throwing out the device, it is necessary to pull back the battery

DISPOSING OF THE UNIT

cells and get rid of them safely for recycling reasons.

◆ When you need to dispose of the unit, consult your dealer. If pipes are

removed incorrectly, refrigerant may blow out and come into contact

with your skin, causing injury. Releasing refrigerant into the atmosphere

also damages the environments.

◆ Please recycle or dispose of the packaging material for this product in

an environmentally responsible manner.

◆ Never store or ship the air conditioner upside down or sideways to

O^THERS

avoid damage to the compressor.

◆ The appliance is not intended for use by young children or infirm

persons without supervision: Young children should be supervised to

ensure that they do not play with the appliance.

◆ Max current is measured according to IEC standard for safety and

current is measured according to ISO standard for energy efficiency.

E-2

Contents

◆

PREPARING YOUR AIR CONDITIONER

◆◆◆Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

◆◆◆View of the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

◆◆◆Remote Control-Buttons and Display . . . . . . . . . . . . . . . . . . . . . .

◆◆◆Wired Remote Controller-Buttons and Display . . . . . . . . . . . . . . .

◆◆◆Centralized Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

◆◆◆Function Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

◆◆◆Getting Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

◆◆◆Inserting the Remote Control Batteries . . . . . . . . . . . . . . . . . . . . . 12

◆

OPERATING YOUR AIR CONDITIONER

◆◆◆Selecting the Automatic Operating Mode . . . . . . . . . . . . . . . . . . . 13

◆◆◆Cooling Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

◆◆◆Heating Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

◆◆◆Changing the Room Temperature Quickly . . . . . . . . . . . . . . . . . . 16

◆◆◆Removing Excess Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

◆◆◆Airing Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

◆◆◆Adjusting the Air Flow Direction Vertically . . . . . . . . . . . . . . . . . . . 19

◆◆◆Adjusting the Air Flow Direction Horizontally . . . . . . . . . . . . . . . . 19

◆

PROGRAMMING YOUR AIR CONDITIONER

◆◆◆Setting the On Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

◆◆◆Setting the Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

◆◆◆Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

RECOMMENDATIONS FOR USE

◆◆◆Operating Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

◆◆◆Temperature and Humidity Ranges . . . . . . . . . . . . . . . . . . . . . . . . 24

◆◆◆Operating Your Air Conditioner Without the Remote Control . . . . . 24

◆◆◆Solving Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

◆◆◆Cleaning Your Air Conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

◆◆◆Cleaning Deodorizing and Bio Filters (Option) . . . . . . . . . . . . . . . 27

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed with other household

wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled

waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable

reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government

office, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract.

This product should not be mixed with other commercial wastes for disposal.

E-3

View of the Unit

The design and shape are subject to change according to the model.

Indoor Unit

Room temperature sensor

Air Inlet

Auto grille

On/Off switch

Air filter

(under the grille)

Remote Control Sensor

Air flow blades

(outlet)

Operation indicator

Set temperature &

room temperature

Timer indicator

Sleep Timer indicator

Fan speed setting

Note

◆ If you want to turn On/Off the Display during operation,

press the button on the remote control.

◆ The room temperature sensor senses air temperature around

the sensor, and shows the temperature on the display.

E-4

Remote Control - Buttons and Display

Operating mode

Remote control

transmission indicator

(

AUTO,

COOL,

DRY,

FAN,

HEAT)

Battery discharge indicator

Fan speed

Turbo mode

Temperature setting

Air flow direction

Sleep mode

Off Timer setting

On Timer setting

On/Off button

Temperature adjustment

buttons

Mode selection button

(AUTO, COOL, DRY, FAN, HEAT)

Digital On/Off button

Swing button

Fan speed adjustment

button

Turbo button

Timer Set/Cancel button

Sleep button

On Timer button

Off Timer button

E-6

Wired Remote Controller-Buttons and Display

The wired remote controller is an optional accessory and it is installed on the wall.

To use the wired remote controller, refer to an appropriate manual.

Operating mode

Centralized controller indicator

(In case of installing the Centralized controller)

Removing frost indicator

Communication

error indicator

Temperature setting

On Timer setting

Off Timer setting

Fan speed

Air flow direction

Filter Sign indicator

Test indicator

On/Off button

Temperature adjustment

buttons

On/Off indicator

Fan speed

adjustment button

On Timer button

Swing button

Timer Set/Cancel button

Test button

Filter Reset button

Mode selection button

Note

◆ The

button is for your installation specialist. You must NOT press it.

button. Then the wired remote

◆ After cleaning the air filter, press the

controller will display the FILTER SIGN indicator when the time to clean the air filter;

refer to page 26 or 27.

E-7

Centralized Controller

The centralized controller is an optional accessory and it is installed on the wall.

To use the centralized controller, refer to an appropriate manual.

Front View

Operating lamp

All On button

All Off button

On/Off indicators

On/Off buttons

Index

Note

◆ The operating lamp comes on even when only one air conditioner

connected to the centralized controller is operating.

E-8

Side View

Operating Mode Switch

COOL

AUTO

HEAT

Note

◆ Choose the appropriate operating mode with the Operating Mode Switch

that enables the user to choose between the Cool/Auto/Heat mode.

E-9

Function Controller

The function controller is an optional accessory and it is installed on the wall.

The function controller is an additional controller which is used with the centralized controller.

To use the function controller, refer to an appropriate manual.

Operating mode

Removing frost indicator

Centralized controller indicator

Communication

error indicator

Temperature setting

Fan speed

Room number display

Air flow direction

Test indicator

Filter Sign indicator

On/Off & Timer

Set/Cancel button

Temperature adjustment

buttons

On/Off indicator

Fan speed adjustment

button

Indoor unit

selection button

Swing button

Test button

Filter Reset button

Mode selection button

Note

◆ The

◆ After cleaning the air filter, press the

will display the FILTER SIGN indicator when the time to clean the air filter.

button is for your installation specialist. You must NOT press it.

button. Then the wired remote controller

E-10

Getting Start

You have just purchased a Free Joint Multi air conditioner and it has

been installed by your installation specialist.

Your Owner’s Instructions contains valuable information on using your

air conditioner. Please take the time to read it as it will help you take full

advantage of the unit’s features.

The booklet is organized as follows.

◆ The following figures are shown on pages from 4 to 6 :

Indoor unit

Remote control(buttons and display)

They will help you find the buttons and understand the symbols displayed.

◆ In the manual, you will find a series of step-by-step procedures for each

function available.

The illustrations in the step-by-step procedures use three different symbols:

PRESS

PUSH

HOLD DOWN

E-11

Inserting the Remote Control Batteries

You must insert or replace the remote control batteries when:

◆ You purchase the air conditioner

◆ The remote control does not work correctly

Note

◆ Use two AAA, LR03 1.5V batteries.

◆ Do not use old batteries or different kinds of batteries together.

◆ Batteries may be completely discharged after 12 months, even

◆ if they have not actually been used.

Push the battery cover on the rear of the remote control with your thumb

in the direction of the arrow and remove it.

Insert the two batteries, taking care to respect the polarities:

◆ + on the battery with + on the remote control.

◆ - on the battery with - on the remote control.

Close the cover by sliding it back until it clicks into place.

E-12

Selecting the Automatic Operating Mode

You can start the air conditioner in Automatic mode from your remote

control. In the Automatic mode, the optimum temperature and the fan

speed is selected automatically.

If necessary, press the

(On/Off) button.

Result:

◆ The operation indicator on the indoor unit lights up.

◆ The air conditioner starts up in the mode selected

when the unit was last used.

◆ The indoor unit beeps.

IMPORTANT

The air conditioner is fitted with a protection mechanism

to prevent the unit from being damaged when it is started

immediately after being:

◆ Plugged in

◆ Stopped

lt will start up normally after three minutes.

If the

is not displayed at the top of the remote control,

press the

appears.

button on the remote control one or more times until it

Result:

◆ The indoor unit beeps each time you press the

button.

◆ The air conditioner runs in AUTO mode.

Note

You can change modes at any time.

E-13

Cooling Your Room

You must select the Cool mode if you wish to adjust the:

◆ Cooling temperature

◆ Fan speed when cooling

If necessary, press the

(On/Off) button.

Result: The operation indicator on the indoor unit lights up.

◆

◆ The air conditioner starts up in the mode selected

when the unit was last used.

◆ The indoor unit beeps.

IMPORTANT

The air conditioner is fitted with a protection mechanism

to prevent the unit from being damaged when it is started

immediately after being:

◆ Plugged in

◆ Stopped

lt will start up normally after three minutes.

If the

is not displayed at the top of the remote control,

press the

appears.

button on the remote control one or more times until it

Result:

◆

The indoor unit beeps each time you press the

The air conditioner runs in COOL mode.

button.

Note

You can change modes at any time.

To adjust the temperature, press the

the required temperature is displayed.

button one or more times until

Possible temperatures are between 18°C and 30°C inclusive.

Result: Each time you press the button:

◆

- The temperature is adjusted by 1°C

- The indoor unit beeps

◆ The air conditioner starts cooling, provided that the room

temperature is higher than the selected temperature.

◆ If the room temperature reaches the set temperature, the air

conditioner stops cooling, but the fan is still operating.

Select the fan speed by pressing the

until the required setting is displayed:

button one or more times

)

Automatic (rotated :

Low

Medium

High

Result:

Each time you press the

beeps.

button, the indoor unit

To control the direction of the air flow, refer to page 19.

E-14

Heating Your Room

You must select the Heat mode if you wish to adjust the:

◆ Heating temperature

◆ Fan speed when heating

If necessary, press the

(On/Off) button.

Result: The operation indicator on the indoor unit lights up.

◆

◆ The air conditioner starts up in the mode selected

when the unit was last used.

◆ The indoor unit beeps.

The air conditioner is fitted with a protection mechanism

to prevent the unit from being damaged when it is started

immediately after being:

IMPORTANT

◆ Plugged in

◆ Stopped

It will start up normally after three minutes.

If the

is not displayed at the top of the remote control, press the

button on the remote control one or more times until it appears.

Result:

◆

The indoor unit beeps each time you press the

The air conditioner runs in HEAT mode.

button.

Note

You can change modes at any time.

To adjust the temperature, press the

button one or more times

until the required temperature is displayed.

Possible temperatures are between 16°C and 30°C inclusive.

Result: ◆ Each time you press the button:

- The temperature is adjusted by 1°C

- The indoor unit beeps

◆ The air conditioner starts heating, provided that the room

temperature is lower than the desired temperature

(selected temperature+3°C).

◆ If the room temperature reaches the set temperature, the air

conditioner stops heating, but the fan is still operating.

Select the fan speed by pressing the

until the required setting is displayed:

button one or more times

)

Automatic (rotated :

Low

Medium

High

Result:

◆

Each time you press the

button, the indoor unit beeps.

For the first 3 to 5 minutes, the fan operates very

slowly until the air has been sufficiently warmed. Once the

correct temperature has been reached, the fan is automatically

set to the required speed.

To control the direction of the air flow, refer to page 19.

E-15

Changing the Room Temperature Quickly

The Turbo cooling/heating function is used to cool or heat your room as

quickly as possible.

For example : You have just come home and find that the room is very

hot. You wish to cool it down as quickly as possible.

The Turbo function operates for 30 minutes with the maximum settings before

returning automatically to the mode and temperature previously selected.

If necessary, press the

(On/Off) button.

Result:

◆ The operation indicator on the indoor unit lights up.

◆ The air conditioner starts up in the mode selected

when the unit was last used.

◆ The indoor unit beeps.

Press the

Result:

button.

◆ The temperature and fan settings are adjusted automatically.

◆ The air conditioner cools or heats the room as quickly as possible.

◆ After 30 minutes, the air conditioner is reset automatically to the

previous mode, temperature and fan settings.

But, if you press the

button in DRY or FAN mode,

it will change to AUTO mode automatically.

If you wish to stop the Turbo function before the end of the 30-minute period,

press the

button again.

Result:

The air conditioner is reset automatically to the previous mode,

temperature and fan settings.

To control the direction of the air flow, refer to page 19.

E-16

Removing Excess Humidity

If the atmosphere in your room is very humid or damp, you can

remove excess humidity without lowering the room temperature too

much.

If necessary, press the

(On/Off) button.

Result: The operation indicator on the indoor unit lights up.

◆

◆ The air conditioner starts up in the mode selected

when the unit was last used.

◆ The indoor unit beeps.

IMPORTANT

The air conditioner is fitted with a protection mechanism

to prevent the unit from being damaged when it is started

immediately after being:

◆ Plugged in

◆ Stopped

It will start up normally after three minutes.

If the

is not displayed at the top of the remote control, press the

button on the remote control one or more times until it appears.

Result:

◆

The indoor unit beeps each time you press the

The air conditioner runs in DRY mode.

button.

Note

You can change modes at any time.

To adjust the temperature, press the

button one or more times

until the required temperature is displayed.

Possible temperatures are between 18°C and 30°C inclusive.

Result: ◆ Each time you press the button:

- The temperature is adjusted by 1°C

- The indoor unit beeps

◆ The air conditioner starts removing the excess humidity;

the quantity of air is adjusted automatically.

To control the direction of the air flow, refer to page 19.

E-17

Airing Your Room

If the atmosphere in your room is stale, you can air the room using

the Fan feature.

If necessary, press the

(On/Off) button.

Result:

◆

The operation indicator on the indoor unit lights up.

◆ The air conditioner starts up in the mode selected

when the unit was last used.

◆ The indoor unit beeps.

If the

is not displayed at the top of the remote control,

press the

appears.

button on the remote control one or more times until it

Result:

◆

The indoor unit beeps each time you press the

The air conditioner runs in FAN mode.

The temperature is set automatically.

button.

Note

You can change modes at any time.

Select the fan speed by pressing the

until the required setting is displayed:

button one or more times

Low

Medium

High

Result: Each time you press the

button, the indoor unit beeps.

To control the direction of the air flow, refer to page 19.

E-18

Adjusting the Air Flow Direction Vertically

Depending on the position of the indoor unit on the wall of your room,

you can adjust the position of the outer air flow blade on the bottom

of the unit, thus increasing the efficiency of the air conditioner.

Press the

button one or more times as required.

Result: The outer blade is adjusted vertically.

RECOMMENDATION

When...

Adjust the blade to face...

Cooling

Heating

Upwards.

Downwards.

If you want the blade to move up and down automatically when the air

conditioner is operating, press the

button.

Result: The blade moves up and down, around the base position set.

To stop the blade moving up and down, press the

button again.

Note

If you switch the air conditioner... Then the blade is...

Off

Closed completely.

Set to the initial position powered.

On again

Adjusting the Air Flow Direction Horizontally

There are two sets of inner air flow blades. Just as the outer air flow

blade can be adjusted vertically, the inner blades can be adjusted

horizontally.

Adjust each set of inner blades to the required position, by pushing or

pulling them sideways.

E-19

Setting the On Timer

The On Timer enables you to switch on the air conditioner automatically

after a given period of time. You can set the period of time from

30 minutes to 24 hours.

To set the operating time, press the

button one or more times until

the required time is displayed. Possible time is between 0.5 hour and 24

hours inclusive.

Press the

(Set/Cancel) button to complete the setting.

Result: ◆ The remaining time is displayed.

◆ Blinking of the timer indicator stops.

◆ The selected mode and the temperature on the display

disappear after 10 seconds.

◆ The air conditioner will switch on automatically when the

counter displayed on the remote control reaches the set time

and disappears the On timer setting.

To select an operating mode in advance, press the

button until the

desired mode is displayed at the top of the remote control.

Result: ◆ The air conditioner will run in the selected mode when it is

turned on.

To Cancel the On Timer

Press the

(Set/Cancel) button.

Note

◆ If you press the

button when the Off Timer is set,

the Off Timer is also cancelled.

E-20

Setting the Off Timer

The Off Timer enables you to switch off the air conditioner automatically

after a given period of time. You can set the period of time from

30 minutes to 24 hours.

To set the operating time, press the

button one or more times until

the required time is displayed. Possible time is between 0.5 hour and 24

hours inclusive.

Press the

(Set/Cancel) button to complete the setting.

Result: ◆ The remaining time is displayed.

◆ Blinking of the timer indicator stops.

◆ The air conditioner will switch off automatically when the

counter displayed on the remote control reaches the set time

and disappears the Off timer setting.

Example If you would like to turn the air conditioner on after 2 hours

and to operate it for 2 hours:

1. Press the

2. Press the

3. Press the

4. Press the

button until ‘2.0 Hr’ is displayed.

(Set/Cancel) button.

button until ‘4.0 Hr’ is displayed.

(Set/Cancel) button.

Note

You can see or change the setting mode and/or the temperature

by pressing the

Off timer.

button or the

button after setting the

To Cancel the Off Timer

Press the

(Set/Cancel) button.

Note

◆ If you press the

button when the On Timer is set,

the On Timer is also cancelled.

E-21

Setting the Sleep Timer

The Sleep Timer can be used when you are cooling or heating your

room to switch the air conditioner off automatically after a period of

6 hours.

Note

If you wish to switch the unit off at a specific time, refer to

page 21.

Make sure that you have selected either COOL or HEAT mode.

Press the button.

Result: ◆ The indoor unit beeps.

◆ The air conditioner will be controlled as indicated in the

illustrations below.

Cooling The desired temperature is

increased by 1°C every hour.

When it has been increased

by 2°C (after 2 hours), the

temperature is maintained for

4 hours.

Heating The desired temperature is

decreased by 1°C every hour.

When it has been decreased

by 2°C (after 2 hours), the

temperature is maintained for

4 hours.

To Cancel the Sleep Timer

If you no longer wish to use the Sleep Timer that you have set, you

can cancel it at any time.

Press the

Result:

button.

◆

The indoor unit beeps.

The

is no longer displayed.

The air conditioner operates normally.

E-22

Operating Recommendations

Here are a few recommendations that you should follow when using

your air conditioner.

Topic

Recommendation

Heating performances

The heat pump inside the air conditioner

absorbs heat from outside air and brings it

indoors. If the temperature of the outside air

drops, the air conditioner will heat less. If you

find that the room is not warm enough, use an

additional heating appliance.

Warm air circulation

The air conditioner circulates warm air to heat

your room; as a result, some time will be

required after starting the air conditioner to

warm the entire room. If necessary, set the

air conditioner on before you wish to use

the room.

Frost

When outside temperatures are low and

humidity is high, frost may form in the outdoor

unit when heating is selected.

If this happens:

◆ The heating operation is stopped.

◆ The Defrost mode is triggered automatically

for about 10 minutes.

No intervention is required from you; after

about 10 minutes, the air conditioner starts

operating again normally.

High indoor and outdoor If both the indoor and outdoor temperatures

temperatures

are high and you select the Heat mode, the

outdoor unit’s fan and compressor may stop

at times. This is normal; simply wait until the

air conditioner switches on again.

Power failure

If a power failure occurs when the air conditioner

is operating, the unit is switched off.

When the power returns, the air conditioner starts

up again automatically.

E-23

Temperature and Humidity Ranges

The following table indicates the temperature and humidity ranges within which the air conditioner can be used.

If the air conditioner is used at...

Then...

High temperatures

The automatic protection feature may be triggered and the air conditioner stopped.

Low temperatures

A water leak or some other malfunction may occur if the heat exchanger freezes.

Water may condense on and drip from the surface of the indoor unit if it is used for long periods.

High humidity levels

Mode

Outdoor Temperature

Indoor Temperature

Indoor Humidity

Heating

Cooling

Drying

-15°C to 24°C approx.

-5°C to 43°C approx.

5°C to 43°C approx.

27°C or less

21°C to 32°C approx.

18°C to 32°C approx.

80% or less

❇

The standardized temperature for heating is 7°C. If the outdoor temperature drops to 0°C or below,

the heating capacity can be reduced depending on the temperature condition.

If the cooling operation is used at over 32°C(indoor temperature) then, it does not cool at its full capacity.

Operating Your Air Conditioner Without the Remote Control

Your air conditioner can be operated directly from the indoor unit if

the remote control is lost or broken.

Slide the lower front grille down.

To switch the air conditioner on, press the On/Off switch on the right

side of the indoor unit.

Result: N The Operation indicator on the indoor unit comes on.

N The indoor unit beeps.

N The air conditioner starts up in the most suitable mode for

the room temperature:

Room Temperature

Less than 21°C

21°C or above

Operating Mode

Heat

Cool

To switch the air conditioner off, press the On/Off switch again.

Note

Even if the air conditioner has been switched on via the

On/Off switch, operations can still be controlled using the

remote control as usual.

E-24

Solving Common Problems

Before contacting the after-sales service, perform the following simple checks.

They may save you the time and expense of an unnecessary call.

Problem

Explanation/Solution

The air conditioner does not

operate at all

◆ Check that the breaker used for the air conditioner is switched on.

◆ Check that the operation indicator on the indoor unit is on;

if necessary press the

(On/Off) button on the remote control.

◆ Check whether the TIMER indicator on the indoor unit is switched on.

If so:

- Wait until the switch-on time is reached and the air conditioner starts

up automatically

- Cancel the timer (see pages 20 and 21 for further details)

The air conditioner does not

operate with the remote control

◆ Check that there are no obstacles between you and the indoor unit.

◆ Check the remote control batteries.

◆ Check that you are close enough to the indoor unit

(7 meters/yards or less).

No beep is heard when you press

◆ Check that you are pointing the remote control at the remote control

sensor in the right of the indoor unit.

the

(On/Off) on the remote

control

◆ Replace the remote control batteries if necessary.

The air conditioner does not cool

or heat

◆ Check that the correct operating mode has been selected (AUTO,

COOL, HEAT).

◆ The room temperature may be too low or too high.

◆ Dust may be blocking the air filter guard; refer to page 26 for cleaning

instructions.

◆ Check that there is no obstacle in front of the outdoor unit.

When heating, the required room

temperature is never reached and

the air conditioner frequently stops

◆ Check that the required temperature has been set correctly.

◆ Increase the fan speed.

◆ If the air flow is directed upwards, use the remote control to direct it

downwards.

The fan speed does not change

◆ Check that the operating mode is set to COOL, HEAT or FAN;

in the AUTO mode, the fan speed changes automatically and in

the DRY mode, it is set to AUTO.

when you press the

button

The air flow direction does not

change when you press the

button

◆ Check that the air conditioner has been switched on; if necessary,

press the

(On/Off) button on the remote control.

The timer is not correctly triggered

◆ Check that the timer has been programmed correctly;

see pages 20 and 21.

Odour is permeated in the room

during air conditioning

◆ Air the room.

E-25

Cleaning Your Air Conditioner

For the best use of your air conditioner, you must clean it every

2 weeks regularly to remove the dust that accumulates on the air filter.

Before cleaning your air conditioner, ensure that you

have switched off the breaker used for the unit.

IMPORTANT

Slide the lower front grille down.

Slide the upper front grille up slightly, then open the grille by pulling right

and left sides of the grille.

Disassemble the upper front grille by opening the grille completely.

Lift out the bottom edge of the air filters and pull down to release them.

Grille support

Remove all dust on the air filters with a vacuum cleaner or brush.

When you have finished, insert the top part of the filters into their slot

and push down on the bottom edge until they click into place.

Clean the front grille with a damp cloth and mild detergent (do NOT use

benzene, solvents or other chemicals).

Body groove

Lower

front

grille

Fix the left side of grille support, then insert the right side of grille support.

Hook

Note ◆◆ If you have not used the air conditioner for a long period of time,

set the fan going for 3 to 4 hours to dry the inside of the air conditioner

thoroughly.

◆◆To close the upper front grille completely after cleaning filters, turn on

and turn off the air conditioner.

E-26

Cleaning Deodorizing and Bio Filters (Option)

To remove minute dust particles and odors, deodorizing and Bio filters

are installed in the air conditioner.

You should clean the filters every 3 months.

MH020FPEA/MH023FPEA/MH026FPEA/

MH035FPEA

Open the upper front grille by pulling right and left sides of the grille.

Pull out the deodorizing and Bio filters.

Deodorizing Filter

Bio Filter

Wash the filters with clean water, then dry them in the shade.

Insert the filters into the original position.

MH052FPEA1

Note

You can change the position of filters with each other.

Bio Filter

Close the front grille.

Deodorizing Filter

E-27

Contact SAMSUNG WORLD WIDE

If you have any comments or questions regarding a Samsung product, contact the SAMSUNG customer care center.

Country

Customer Care Center

Web Site

BELGIUM

02 201 2418

www.samsung.com/be

844 000 844

Distributor pro Českou republiku:

Samsung Zrt., česka organizační složka

Vyskočilova 4, 14000 Praha 4

CZECH REPUBLIC

www.samsung.com/cz

DENMARK

FINLAND

70 70 19 70

030-6227 515

www.samsung.com/dk

www.samsung.com/fi

3260 SAMSUNG

08 25 08 65 65 ( 0,15/min)

FRANCE

www.samsung.com/fr

GERMANY

HUNGARY

ITALIA

LUXEMBURG

NETHERLANDS

NORWAY

01805 - 121213 ( 0,14/min)

06-80-SAMSUNG (7267864)

800-SAMSUNG (7267864)

0032 (0)2 201 24 18

0900 20 200 88 ( 0,10/min)

815-56 480

0 801 801 881

80 8 200 128

0800-SAMSUNG (7267864)

902 10 11 30

0771-400 200

POLAND

PORTUGAL

SLOVAKIA

SPAIN

SWEDEN

U.K

REPUBLIC OF IRELAND

SWITZERLAND

RUSSIA

0870 SAMSUNG (7267864)

0818 717 100

0800-SAMSUNG (7267864)

8-800-200-0400

KAZAHSTAN

UZBEKISTAN

UKRAINE

LITHUANIA

LATVIA

8-800-080-1188

8-800-120-0400

8-800-502-0000

8-800-77777

800-7267

ESTONIA

Lexmark X 952dte User Manual
Mitsubishi Electronics Lossnay Lgh 15rx4 E User Manual
Murphy Exhaust Pyrometers 10705146 User Manual
Panasonic Kx Fc175al User Manual
Samsung Clx 6250fx User Manual
Schumacher Mc 1 User Manual
Shinco Air Conditioner Kfr 25gwz Bm User Manual
Soleus Air Air Conditioner Gm Ttw 14hc User Manual
Sony Era 301p4 User Manual
Xerox Document Centre 425 User Manual