Miroil 690hd User Manual

Use Instructions  
back to miroil.com  
for Models - 690HD  
- 690HS  
Table of Contents  
Please choose:  
Page  
1. Title page  
2
3
4
5
6
7
8
2. Dear Customer  
3. Packaging information  
4. Assembly Instructions  
5. Filtering Procedure - HD Series  
6. Filtering Procedure - HS Series  
7. Warranty Registration  
 
Model 690HD  
(Shown below)  
Model 690HS  
(Shown below)  
Includes Basin Filter Model 905  
Includes Pump Out Filter  
Model 690HD / Model 690HS  
Do Not Exceed Rated oil Capacity of 45 lbs (6.5 gallons)  
Division of Oil Process Systems Inc.  
602-20 North Tacoma Street Allentown, Pennsylvania 18103  
PHONE: 610 437-4618 FAX: 610 437-3377 E-mail: [email protected] Web: www.miroil.com  
 
Dear Customer:  
Congratulations on your selection of our Hand Operated Filter Machine which continues over 25 years  
ofleadershipinoilmanagement.  
Your Filter Machine is an important tool for fryer oil management. It is designed to achieve maximum  
performancefor removaloffinecrumbandfoodmaterialsatthelowestcost.  
Another important part of oil management is Frypowder ® oil stabilizer & filter aid. Frypowder ® Oil  
Stabilizer & Filter Aid used with your filter machine will enhance your experience of performance. This  
combination delivers benefits not available from other filter machines.  
Provides consistent and enhanced food quality  
Oil savings from 25% to 40%  
Fryers stay free of carbon and gum deposits  
The MirOil filter doe s not leach harmful chemicals like paper filters  
Faster set-up and clean-up will save on labor  
MirOil filter has a 6 months filter life pro rated guarantee.  
Throw-away paper filters, D. E. powder or expensive cartridges are not needed.  
MirOil "Rinse & Reuse" filter bags clean up in seconds under hot water spray.  
Why Frypowder Oil Stabilizer and Filter Aid and your filter machine deliver these benefits.  
All oil breakdown substances are liquid. They pass through filters and filter aids and remain in the oil. As  
they accumulate, they undermine the nutritional profile and the cooking performance of the oil.  
Frypowderoil stabilizercaptures these breakdown liquid substances as they form.  
This is why Frypowder oil stabilizer is able to provide total control of food quality and oil performance.  
Frypowderoil stabilizerhas no chemistry with the oil or with the food.  
When the oil is filtered, the Frypowder oil stabilizer mineral leave the fryer with the crumb and  
performs as a filter aid for improved filtering.  
To receive the full benefit from your MirOil Filter Machine, just follow these simple rules.  
1. Set up a regular schedule to filter once a day.  
2. AddFrypowderto your oil before each meal session.  
3. Follow the filtering and freshening procedures outlined in this manual.  
For questions aboutFrypowderoil stabilizeror yourPower FilterMachine. . . .  
Frying Hot Line 1.800.523.9844  
Additional Tips  
Order a spare filter bag so you are prepared if it may be required in the future.  
If the oil for discard is held overnight in the kitchen for security reasons or if you need a measure for the  
freshening oil. . . . Order a Model 30LG utility pail - for measuring and / or storing up to 5 gallons of oil.  
Division of Oil Process Systems Inc.  
602-20 North Tacoma Street Allentown, Pennsylvania 18103  
PHONE: 610 437-4618 FAX: 610 437-3377 E-mail: [email protected] Web: www.miroil.com  
 
The following parts are included for assembly  
Carton #1 for Model 690HD & Model 690HS  
Assembly of Hot Oil Pump  
Mounted on Handle  
Wheel Assembly  
Discharge Hose  
Assembly  
Carton #2 for Model 690HD & Model 690HS  
Lid and Screws  
7.5 gallon Oil Drain Basin  
Carton #2 for Model 690HD  
also includes Model D905A Filter Assembly  
Carton #2 for Model 690HS  
also includes Pump Out Filter Assembly  
for drain operation  
compatible with the lift out fry pan  
Model WE28A  
Or Model PUM11A Holder  
Model WDY8A  
Frame & Filter Bag for  
larger lift out fry pans  
in larger fryers  
Holder Frame & Filter Bag  
for smaller fryers  
A Model 900 Filter Bag is to be snapped  
onto the Model 905C Filter Frame.  
Division of Oil Process Systems Inc.  
602-20 North Tacoma Street Allentown, Pennsylvania 18103  
PHONE: 610 437-4618 FAX: 610 437-3377 E-mail: [email protected] Web: www.miroil.com  
 
Assembly of models 690HD / HS  
Step 1  
Step 2.  
Attach the Wheel  
Assembly to the  
Handle and Hot Oil  
Pump Assembly.  
Use the Allen wrench  
and Allen screws in  
the nutserts in the  
handle.  
Insert tube at end of hose (from hot oil  
pump suction) into the socket on the side of  
the Filter Basin until the tube is fully seated.  
Step 3.  
Step 4.  
Remove pin, turn &  
remount crank  
handle from  
Carefully attach the  
quick coupling on the  
end of the Discharge  
Hose to the mating  
fitting on the  
shipping position to  
the correct position  
for pumping.  
pump/handle  
Reinstall pin.  
assembly  
The Filter Machine is ready for use.  
Be sure to read the instructions  
before placing machine into service.  
Assembled  
Model 690HD  
Assembled  
Model 690HS  
Division of Oil Process Systems Inc.  
602-20 North Tacoma Street Allentown, Pennsylvania 18103  
PHONE: 610 437-4618 FAX: 610 437-3377 E-mail: [email protected] Web: www.miroil.com  
 
Filter Procedure for Model 690HD for use with fryers with drain valves.  
CAUTION: Couplethehose. Pullhard on thehoseto makesurethelever armsarelocked.  
Makesurehosenozzleisin thenozzleholder tubeon thepump.  
Filter oilat temperaturesfrom300°F to 350°F  
Step 1- Swing wheelstabilizersinto placeasshown in diagrambelow(figure1).  
Step 2- PlaceEZ FlowModel905Filter in theBasin (seediagramFigure1).  
Carefullyopen thefryer valveto drain oilinto thefilter basin through thefilter bag.  
Step 3- Use a small amount of Frypowder on a damp cloth to clean "ring around the fryer" and any slight  
residueof previouscarbon formation on heating surfaces.  
Aimhosenozzlecarefullyasyou pump oilto flush crumb and powder residuefromfryer.  
Step 4- Closethedrain valveturn pump to return theoilbackto thefryer  
Step 5 - Discard heavy crumb load before filtering the next fryer. Use a bus tray or carton to allow the crumb  
to cool because hot crumb will melt plastic garbage can liners.  
Clean your filter under hot water spray. Store the filter in the filter basin to avoid accidental damage.  
Do not wash the filter in a dishwasher or use soap. The least residue of soap is harmful to the oil.  
If solid oil or shortening is used, before storing the filter machine, turn the pump handle  
clockwiseto emptytheoilfromthepump cavity.  
Uncouple the hose and store it in a hanging position to prevent a fat plug from forming when it  
collectsand solidifiesat aloop or bend of thehose.  
Morenotesfor great fried food:  
1. Add Frypowder oil stabilizer to your oil after filtering and/or before each meal session. This will capture  
oilbreakdown substancesastheyformin theoiland prevent oilbreakdown reactions.  
2. Filter onceadaywhenFrypowderoilstabilizer isused unlesscrumb load isextremelyheavy.  
3. Follow the filtering and freshening procedures described in your brochure for Frypowder oil stabilizer  
and theNewFrying Technologyto choosean oilmanagement programfor your frystation.  
For assistancecall.... 1.800.523.9844  
Figure 1  
Fryer  
Wheel stabilizer in pumping position  
Division of Oil Process Systems Inc.  
602-20 North Tacoma Street Allentown, Pennsylvania 18103  
PHONE: 610 437-4618 FAX: 610 437-3377 E-mail: [email protected] Web: www.miroil.com  
 
Filter Procedure for 690HS Series For countertop fryers with lift out fry pans (No drain valves)  
If you also have fryers with drain valves, buy a D Series Drain Filter for this filter machine  
Use the Filter Procedure for "D" Series for fryers with drain valves  
Refer to diagram on bottom of this page:  
CAUTION: Couple the hose. Pull hard on the hose to make sure the lever arms are locked. Make sure hose  
nozzleisin thenozzleholder on thepump. Lift heatersout of theoiland securethemin this  
Filter oilat temperaturesfrom300°F to 350°F.  
po si ti on .  
Step 1 - Swing wheel stabilizers into place as shown in diagram below  
Step 2 - Carefully immerse the Pump-Out Filter Bag mounted on its holder frame into the oil.  
Install the hose nozzle into the nozzle holder tube of the Pump Out Filter.  
Step 3 - Do not tilt the fryer pan to pump the residue of oil.  
Adjust the height of the bottom of the nozzle to leave the proper amount of oil in the fry pan for  
freshening. Discard thisleft over oilwith thecrumb.  
Thiscontrolled discard willtaketheplaceof thePartialDiscard Procedureof theFrying Program.  
Step 4 - Rinse the fry pan only with hot water - no soap. To clean "ring around the fry pan" and any carbon  
formation on the heating surfaces use someFrypowder on a damp cloth.  
Step 5 - Turn pump handle counterclockwise to pump the oil back to the the fry pan.  
Do not wash the filter in a dishwasher or use soap. The least residue of soap is harmful to the oil.  
If solid shortening is used, uncouple the hose and store it in a hanging position to prevent a fat plug  
fromforming when it collectsand solidifiesat aloop or bend of thehose.  
Morenotesfor great fried food:  
1. Add Frypowder oil stabilizer to your oil after filtering and/or before each meal session. This will capture  
oilbreakdown substancesastheyformin theoiland prevent oilbreakdown reactions.  
2. Filter onceadaywhenFrypowderoilstabilizer isused unlesscrumb load isextremelyheavy.  
3. Follow the filtering and freshening procedures described in your brochure for Frypowder oil stabilizer  
and theNewFrying Technologyto choosean oilmanagement programfor your frystation.  
For assistancecall.... 1.800.523.9844  
Pump out filter  
with nozzle  
support tube  
Counter Top Fryer  
with lift out FryPan  
Division of Oil Process Systems Inc.  
602-20 North Tacoma Street Allentown, Pennsylvania 18103  
PHONE: 610 437-4618 FAX: 610 437-3377 E-mail: [email protected] Web: www.miroil.com  
 
Loss or Damage During Shipment  
Inspect all cartons for damage before unpacking. Your MirOil pump was thoroughly inspected before  
leaving our factory. The carrier is responsible for safe delivery. All claims for any loss or damage in transit  
must be made to the carrier. MirOil will assist with claimsIFdamage has been promptly reported to the carrier.  
1 Year Limited Warranty on your Filter Machine  
This product is warranted only against defects in workmanship or materials for 1 year from date of the  
filter machine is placed in service or not longer than 15 months from date of purchase. Liability under  
the basic 1 year limited warranty is limited to replacing or repairing parts FOB Allentown PA. Parts  
must be returned to our factory with shipping costs prepaid. The 1 year warranty does not cover the  
costsofservicelabororshipping to replaceparts.  
The use of the filter pump for pumping any liquid other than fryer oil will contaminate the pump and  
piping. Thiswill contaminatetheoil and mayvoid thiswarranty  
6 month Limited Warranty on your Filter Bag  
The filter bag has a pro rata warranty for 6 months. This is similar to a warranty for a battery or tire. The  
filter bag must be returned to MirOil for repair, FOB Allentown, PA 18103. If the filter bag is not able to  
be repaired, It will be replaced with a new filter bag at the prevailing cost. Credit toward the purchase of  
the new filter bag will be provided for the unused service life of the old filter bag. This warranty does not  
coverthecostsshippingto replaceparts.  
Important Limits for Coverage Under All Warranties  
No warranty described above covers the replacement of parts that become inoperative because of  
wear (except filter bags) or abuse or for parts subjected to abuse/misuse, negligence, accident or if the  
product has been improperly repaired or altered by user or a 3rd party. No other warranty, expressed or  
implied, is authorized to be made by any parties on behalf of MirOil.  
The manufacturer and the manufacturer's sales agents and/or agencies accept no liability for the use  
or misuse of this machine. Expressly excluded from warranty are implied warranties of  
merchantability and fitness for purpose. Manufacturer, agents and sales agencies disclaim all liability  
foraccidentsresulting fromuseorthemisuseofthisequipment.  
Toll Free Call for warranty information 1.800.523.9844  
Cut and fax / send lower portion  
Cut and fax / send lower portion  
Cut and fax / send lower portion  
Avoid losing protection under the Warranty  
FAX this Warranty Registration promptly to (610) 437 3377  
or . . . add postage and mail to:  
602-20 N. TacomaSt., Allentown, PA18103  
Filter Machine Model No. __________________________  
Oil Pump Model No. ______________________________  
Filter Bag Model No.______________________________  
Owner ___________________________________________  
Contact Person ___________________________________  
Purchased From __________________________________  
Serial No. ____________________  
Serial No. ____________________  
Serial No. ____________________  
Date purchased ___________________________________ Date placed in service ___________  
Division of Oil Process Systems Inc.  
602-20 North Tacoma Street Allentown, Pennsylvania 18103  
PHONE: 610 437-4618 FAX: 610 437-3377 E-mail: [email protected] Web: www.miroil.com  

Mitsubishi Electronics Muz Fd12na U1 User Manual
Murphy Bc1524 User Manual
Panasonic 58 Ghz Expandable Digital Cordless Answering System Kx Tg6073 User Manual
Panasonic Kx Mb2060 User Manual
Panasonic Kx Tcd515e User Manual
Panasonic Telephone Answering Maching Kx F115 User Manual
Samsung Ast18b1 User Manual
Troy Bilt Automobile Parts 78 User Manual
Vtech Ls6426 4 User Manual
York 13 Series User Manual