848J9893A1 (708)
G
B
OWNER’S MANUAL
BRUSHCUTTERS
BC2310DL
Download from Www.Somanuals.com. All Manuals Search And Download.
BC2310DL
G
B
EC DECLARATION OF COMFORMITY
We,
ZENOAH CO., LTD.
1-9, Minamidai, Kawagoe, Saitama, Japan
declare in sole responsibility that the following products referred to in this
declaration conform with
DIRECTIVE 89/336/EEC, 98/37/EC, 2000/14/EC, 2002/88/EC, 2002/44/EC
EN ISO 11806 : 1997
The products referred to are:
DESIGNATION
MODELS
: BRUSHCUTTER
: BC2310DL
SERIAL NUMBERS
: 51100101 and up
The company named above will keep on file the following technical docu-
mentation for any inspection purpose.
• Operation instructions
• Plans and Drawings
• Description of measures designed to ensure conformity
• Other technical documentation
:Specification sheet
Inspection standard
Saitama, Japan
1st April 2007
Masahiko GOUDA
General Manager, Quality Assurance Department
SAFETY FIRST
Instructions contained in warnings within this manual marked
with a symbol concern critical points which must be taken
Contents
into consideration to prevent possible serious bodily injury, and
for this reason you are requested to read all such instructions
carefully and follow them without fail.
1. Parts location .................................................. 4
2. Specifications ................................................. 4
3. Warning labels on the machine ...................... 5
4. Symbols on the machine ................................ 5
5. For safe operation........................................... 6
6. Set up ............................................................. 9
7. Fuel ............................................................... 10
8. Operation ...................................................... 11
9. Maintenance ................................................. 13
10. Storage ......................................................... 15
11. Disposal ........................................................ 15
12. Troubleshooting guide .................................. 16
WARNINGS IN THE MANUAL
WARNING
This mark indicates instructions, which must be followed in or-
der to prevent accidents, which could lead to serious bodily in-
jury or death.
IMPORTANT
This mark indicates instructions, which must be followed, or it
leads to mechanical failure, breakdown, or damage.
NOTE
This mark indicates hints or directions useful in the use of the
product.
GB-3
Download from Www.Somanuals.com. All Manuals Search And Download.
BC2310DL
1. Parts location
5
(1) Primer pump
(2) Air cleaner cover
(3) Choke lever
3
14
2
1
13
(4) Fuel tank
4
(5) Starter knob
(6) Line head
11
12
(7) Gear case
9
(8) Cutting attachment guard
(9) Loop handle
(10) Shaft tube
(11) Suspention point
(12) Throttle trigger
(13) Stop switch
(14) Throttle cable
10
7
8
6
2. Specification
Overall size (L 3 W 3 H) ........................................................... 1765 x 330 x 310 mm
Dry weight .......................................................................................................... 5.4 kg
Engine
Type ............................................................................ Air-cooled 2-stroke gasoline
Model ............................................................................................. Zenoah G24LS
Displacement ........................................................................................... 22.5 cm3
Fuel............................................................................ Mixture (Gasoline 50 : Oil 1)
(when using ZENOAH genuine oil)
Carburetor .................................................................................... Diaphragm type
Ignition system ................................................................................................ C.D.I
Spark plug ........................................................................................ NGK BPMR7A
Fuel tank capacity................................................................................................. 0.6 L
Starter ...................................................................................................... Recoil starter
Clutch.................................................................................................. Centrifugal type
Reduction ratio .................................................................................................... 1.462
Cutting head rotating direction ............................. Counter-clockwise (Operator view)
Specifications are subject to change without notice.
GB-4
Download from Www.Somanuals.com. All Manuals Search And Download.
BC2310DL
3. Warning labels on the machine
15m (50ft)
G
B
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(1) Read owner’s manual before operating this machine.
(2) Wear head, eye and ear protection.
(3) Wear foot protection.
(4) Wear gloves.
(5) Beware of thrown objects.
(6) Warning / Attention
(7) Keep all children, bystanders and helpers 15 meters away from the machine.
If warning label peels off or becomes soiled and
impossible to read, you should contact the
dealer from which you purchased the product
to order new labels and affix them in the required
location(s).
Never modify your machine.
We won’t warrant the machine, if you use the
remodeled brushcutter or if you don’t observe
the proper usage written in the manual.
4. Symbols on the machine
For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications,
please be careful not to make a mistake.
The port to refuel the “MIX GASOLINE”
Position: FUEL TANK CAP
The direction to close the choke
Position: AIR CLEANER COVER
The direction to open the choke
Position: AIR CLEANER COVER
GB-5
Download from Www.Somanuals.com. All Manuals Search And Download.
BC2310DL
5. For safe operation
b. At night, at times of heavy fog,
or at any other times when
your field of vision might be
limited and it would be diffi-
cult to gain a clear view of the
working area.
1. Read this manual carefully until
you completely understand and
follow all safety and operating
instructions.
2. Keep this manual handy so that
you may refer to it later when-
ever any questions arise. Also
note, if you have any questions
which cannot be answered
herein, contact the dealer from
whom you purchased the prod-
uct.
c. During rain storms, during
lightning storms, at times of
strong or gale-force winds, or
at any other times when
weather conditions might
make it unsafe to use the
product.
3. Always be sure to include this
manual when selling, lending, or
otherwise transferring the own-
ership of this product.
4. Never allow children or anyone
unable to fully understand the
directions given in the manual
to use the machine.
WORKING PLAN
1. You should never use the prod-
uct when under the influence of
alcohol, when suffering from ex-
haustion or lack of sleep, when
suffering from drowsiness as a re-
sult of having taken cold medicine
or at any other time when a pos-
sibility exists that your judgment
might be impaired or that you
might not be able to operate the
product properly and in a safe
manner.
WORKING CONDITION
1. When using the product, you
should wear proper clothing and
protective equipment.
2. When planning your work sched-
ule, allow plenty of time to rest.
Limit the amount of time over
which the product is to be used
continuously to somewhere
around 30 ~ 40 minutes per ses-
sion, and take 10 ~ 20 minutes of
rest between work sessions. Also
try to keep the total amount of
work performed in a single day
under 2 hours or less.
(1) Helmet
(2) Ear protectors
(3) Protection goggles or face
protector
(4) Thick work gloves
(5) Non-slip-sole work boots
2. And you should carry with you.
(1) Attached tools
(2) Properly reserved fuel
(3) Spare blade
(4) Things to notify your working
area (rope, warning signs)
(5) Whistle (for collaboration or
emergency)
(6) Hatchet or saw (for removal of
obstacles)
WARNING
1. If you don’t observe the working
time, or working manner (See
“USING THE PRODUCT”), Re-
petitive Stress Injury (RSI) could
occur.
3. Do not wear loose clothing, jew-
elry, short trousers, sandals, or go
barefoot. Do not wear anything
which might be caught by a mov-
ing part of the unit. Secure hair
so it is above shoulder length.
If you feel discomfort, redness and
swelling of your fingers or any
other part of your body, see a doc-
tor before getting worse.
2. To avoid noise complaints, in gen-
eral, operate product between
8 a.m. and 5 p.m. on weekdays
and 9 a.m. to 5 p.m. on weekends.
WORKING CIRCUMSTANCE
1. Never start the engine inside a
closed room or building. Exhaust
gases contain dangerous carbon
monoxide.
2. Never use the product,
a. when the ground is slippery
or when you can’t maintain a
steady posture.
IMPORTANT
Check and follow the local regu-
lations as to sound level and
hours of operations for the prod-
uct.
GB-6
Download from Www.Somanuals.com. All Manuals Search And Download.
BC2310DL
5. For safe operation
and hold it firmly in place so as to
ensure that neither the cutting
part nor the throttle come into
contact with any obstacle when
the engine starts.
BEFORE STARTING
THE ENGINE
1. The area within a perimeter of
15 m of the person using the
product should be considered a
hazardous area into which no one
should enter. If necessary, yellow
warning rope, warning signs
should be placed around the pe-
rimeter of the area. When work is
to be performed simultaneously
by two or more persons, care
should also be taken to constantly
look around or otherwise check
for the presence and locations of
other people working so as to
maintain a distance between
each person sufficient to ensure
safety.
G
B
WARNING
Never place the throttle into the
high-speed position when starting
the engine.
3. After starting the engine, check
to make sure that the cutting at-
tachment stops rotating when the
throttle is moved fully back to its
original position. If it continues to
rotate even after the throttle has
been moved fully back, turn off
the engine and take the unit to
your authorized ZENOAH servic-
ing dealer for repair.
2. Check the condition of working
area to avoid any accident by hit-
ting hidden obstacles such as
stumps, stones, cans, or broken
glass.
USING THE PRODUCT
IMPORTANT
IMPORTANT
Cut only materials recommended by
the manufacturer. And use only for
tasks explained in the manual.
Remove any obstacle before begin-
ning work.
1. Grip the handles firmly with both
hands using your whole hand.
Place your feet slightly apart
(slightly further apart than the
width of your shoulders) so that
your weight is distributed evenly
across both legs, and always be
sure to maintain a steady, even
posture while working.
3. Inspect the entire unit for loose
fasteners and fuel leakage. Make
sure that the cutting attachment
is properly installed and securely
fastened.
4. Be sure to attach the cutting at-
tachment guard securely in
place, or you may get serious in-
jury.
5. Always use the shoulder strap.
Adjust the strap for comfort be-
fore starting the engine. The strap
should be adjusted so the left
hand can comfortably hold the
handlebar grip approximately
waist high.
2. Keep cutting attachment below
waist level.
3. Maintain the speed of the engine
at the level required to perform
cutting work, and never raise the
speed of the engine above the
level necessary.
4. If the unit starts to shake or vi-
brate, turn off the engine and
check the whole unit. Do not use
it until the trouble has been prop-
erly corrected.
5. Keep all parts of your body away
from rotating cutting attachment
and hot surfaces.
6. Never touch the muffler, spark
plug, or other metallic parts of the
engine while the engine is in op-
eration or immediately after shut-
ting down the engine. Doing so
STARTING THE ENGINE
1. Keep bystanders and animals at
least 15 m away from the operat-
ing point. If you are approached,
immediately stop the engine.
2. The product is equipped with a
centrifugal clutch mechanism, so
the cutting attachment begins to
rotate as soon as the engine is
started by putting the throttle into
the start position. When starting
the engine, place the product
onto the ground in a flat clear area
GB-7
Download from Www.Somanuals.com. All Manuals Search And Download.
BC2310DL
5. For safe operation
could result in serious burns or elec-
trical shock.
HANDLING FUEL
1. The engine of the ZENOAH prod-
uct is designed to run on a mixed
fuel, which contains highly flam-
mable gasoline. Never store cans
of fuel or refill the tank of the unit
in any place where there is a
boiler, stove, wood fire, electrical
sparks, welding sparks, or any
other source of heat or fire which
might ignite the fuel.
• IF SOMEONE COMES
1. Guard against hazardous situa-
tions at all times. Warn adults to
keep pets and children away from
the area. Be careful if you are ap-
proached. Injury may result from
flying debris.
2. If someone calls out or otherwise
interrupts you while working, al-
ways be sure to turn off the en-
gine before turning around.
2. Never smoke while operating the
unit or refilling its fuel tank.
3. When refilling the tank, always
turn off the engine and allow it to
cool down. Take a careful look
around to make sure that there are
no sparks or open flames any-
where nearby before refueling.
4. Wipe spilled fuel completely us-
ing a dry rag if any fuel spillage
occurs during refueling.
5. After refueling, screw the fuel cap
back tightly onto the fuel tank and
then carry the unit to a spot 3 m
or more away from where it was
refueled before turning on the en-
gine.
MAINTENANCE
1. In order to maintain your product
in proper working order, perform
the maintenance and checking
operations described in the
manual at regular intervals.
2. Always be sure to turn off the en-
gine and disconnect the spark
plug wire before performing any
maintenance or checking proce-
dures.
WARNING
The metallic parts reach high tem-
peratures immediately after stop-
ping the engine.
TRANSPORTATION
1. When hand-carrying the product,
cover over the cutting part if nec-
essary, lift up the product and
carry it paying attention to the
blade.
2. Never transport the product over
rough roads over long distances
by vehicle without removing all
fuel from the fuel tank. If doing so,
fuel might leak from the tank dur-
ing transport.
3. When replacing the cutting at-
tachment or any other part, or
when replacing the oil or any lu-
bricant, always be sure to use
only ZENOAH products or
products which have been cer-
tified by ZENOAH for use with
the ZENOAH product.
4. In the event that any part must be
replaced or any maintenance or
repair work not described in this
manual must be performed,
please contact a representative
from the store nearest ZENOAH
authorized servicing dealer for
assistance.
5. Do not use any accessory or at-
tachment other than those bear-
ing the ZENOAH mark and rec-
ommended for the unit.
6. Under no circumstances should
you ever take apart the product
or alter it in any way. Doing so
might result in the product be-
coming damaged during opera-
tion or the product becoming un-
able to operate properly.
GB-8
Download from Www.Somanuals.com. All Manuals Search And Download.
BC2310DL
6. Set up
INSTALLING HANDLE
• Mount the handle to the shaft tube and clamp it at a
location that is comfortable to you.
G
B
(1)
(1) About 28cm (11 inches)
INSTALLING CUTTING ATTACHMENT GUARD
• Attach the cutting attachiment guard with the bolts
provided while inserting the spacer between the guard
and the pipe.
• Attach the guard skirt on the guard.
INSTALLING CUTTING HEAD
1. Remove the plastic tube that is attached to the gear
shaft.
2. Firmly screw the line head assembly onto the gear
shaft by hand while locking the gear shaft by insert-
ing the tool into the upper holder on the gear box.
GB-9
Download from Www.Somanuals.com. All Manuals Search And Download.
BC2310DL
7. Fuel
■ FUEL
3. Pour in all of the oil and agitate well.
4. Pour in the rest of gasoline and agitate again for at
least one minute. As some oils may be difficult to agi-
tate depending on oil ingredients, sufficient agitation
is necessary for the engine to last long. Be careful
that, if the agitation is insufficient, there is an increased
danger of early piston seizing due to abnormally lean
mixture.
WARNING
• Gasoline is very flammable. Avoid smoking or
bringing any flame or sparks near fuel. Make sure
to stop the engine and allow it cool before refuel-
ing the unit. Select outdoor bare ground for fuel-
ing and move at least 3 m (10 ft) away from the
fueling point before starting the engine.
5. Put a clear indication on the outside of the container
to avoid mixing up with gasoline or other containers.
6. Indicate the contents on outside of container for easy
identification.
■ FUELING THE UNIT
1. Untwist and remove the fuel cap. Rest the cap on a
dustless place.
2. Put fuel into the fuel tank to 80% of the full capacity.
3. Fasten the fuel cap securely and wipe up any fuel
spillage around the unit.
• The Zenoah engines are lubricated by oil specially
formulated for air-cooled 2-cycle gasoline engine use.
If Zenoah oil is not available, use an anti-oxidant
added quality oil expressly labeled for air-cooled 2-
cycle engine use (JASO FC GRADE OIL or ISO EGC
GRADE).
WARNING
1. Select bare ground for fueling.
2. Move at least 10 feet (3 meters) away from the fu-
eling point before starting the engine.
3. Stop the engine before refueling the unit. At that
time, be sure to sufficiently agitate the mixed gaso-
line in the container.
• Do not use BIA or TCW (2-stroke water-cooling type)
mixed oil.
■ FOR YOUR ENGINE LIFE, AVOID:
1. FUEL WITH NO OIL (RAW GASOLINE) – It will cause
severe damage to the internal engine parts very
quickly.
2. GASOHOL – It can cause deterioration of rubber and/
or plastic parts and disruption of engine lubrication.
3. OIL FOR 4-CYCLE ENGINE USE – It can cause spark
plug fouling, exhaust port blocking, or piston ring stick-
ing.
■ RECOMMENDED MIXING RATIO
GASOLINE 50 : OIL 1
<when using ZENOAH genuine oil>
• Exhaust emission are controlled by the funda-
mental engine parameters and components (eq.,
carburation, ignition timing and port timing) with-
out addition of any major hardware or the intro-
duction of an inert material during combustion.
• These engines are certified to operate on unleaded
gasoline.
4. Mixed fuels which have been left unused for a pe-
riod of one month or more may clog the carburetor
and result in the engine failing to operate properly.
5. In the case of storing the product for a long period of
time, clean the fuel tank after rendering it empty. Next,
activate the engine and empty the carburetor of the
composite fuel.
• Make sure to use gasoline with a minimum octane
number of 89RON (USA/Canada: 87AL).
• If you use a gasoline of a lower octane value than
prescribed, there is a danger that the engine tem-
perature may rise and an engine problem such as
piston seizing may consequently occur.
6. In the case of scrapping the used mixed oil container,
scrap it only at an authorized repository site.
NOTE
• Unleaded gasoline is recommended to reduce the
contamination of the air for the sake of your health
and the environment.
As for details of quality assurance, read the description
in the section Limited Warranty carefully. Moreover, nor-
mal wear and change in product with no functional influ-
ence are not covered by the warranty. Also, be careful
that, if the usage in the instruction manual is not observed
as to the mixed gasoline, etc. described therein, it may
not be covered by the warranty.
• Poor quality gasolines or oils may damage sealing
rings, fuel lines or fuel tank of the engine.
■ HOW TO MIX FUEL
IMPORTANT
Pay attention to agitation.
1. Measure out the quantities of gasoline and oil to be
mixed.
2. Put some of the gasoline into a clean, approved fuel
container.
GB-10
Download from Www.Somanuals.com. All Manuals Search And Download.
BC2310DL
8. Operation
STARTING ENGINE
WARNING
WARNING
The product is equipped with a centrifugal clutch
mechanism, so the cutting attachment begins to ro-
tate as soon as the engine is started by putting the
throttle into the start position. When starting the en-
gine, place the product onto the ground in a flat clear
area and hold it firmly in place so as to ensure that
neither the cutting part nor the throttle come into con-
tact with any obstacle when the engine starts.
The cutting head will start rotating upon the engine
starts.
G
B
1. Feed fuel into the fuel tank and tighten the cap se-
curely.
2. Rest the unit on a flat, firm place. Keep the cutting
head off the ground and clear of surrounding objects,
as it will start rotating upon starting of the engine.
3. Push the primer pump several times until overflown
fuel flows out in the clear tube.
IMPORTANT
• Avoid pulling the rope to its end or returning it by re-
leasing the knob. Such actions can cause starter fail-
ures.
7. Move the choke lever downward to open the choke.
And restart engine.
8. Allow the engine to warm up for a several minutes
before starting operation.
(1) Choke lever (2) Close (3) Open
(4) Purimer pump
NOTE
4. Move the choke lever to the closed position.
5. Set the ignition switch to the “I” position. Set the throttle
lever to the start position (1 → 2 → 3).
1. When restarting the engine immediately after stop-
ping it, leave the choke open.
Place the unit on a flat, firm place.
Keep the cutting head clear of everything around it.
2. Overchoking can make the engine hard to start due
to excess fuel. When the engine failed to start after
several attempts, open the choke and repeat pulling
the rope, or remove the spark plug and dry it.
Stop
Start
1
3. Ignition switch
STOPPING ENGINE
T
R
A
ST
Stop
Start
Ignition switch
2
T
R
A
T
S
6. While holding the unit firmly, pull out the starter rope
quickly until engine fires.
1. Release the throttle lever and run the engine for half
a minute.
2. Shift the ignition switch to the STOP position.
IMPORTANT
• Except for an emergency, avoid stopping the engine
while pulling the throttle lever.
GB-11
Download from Www.Somanuals.com. All Manuals Search And Download.
BC2310DL
8. Operation
ADJUSTING THROTTLE CABLE
• The normal play is 1 or 2 mm when measured at the
carburetor side end. Readjust with the cable adjuster
as required.
TRIMMING GRASS AND WEEDS
• Always remember that the TIP of the line does cut-
ting. You will achieve better results by not crowding
the line into the cutting area. Allow the unit to trim at
its own pace.
1. Hold the unit so the head is off the ground and is tilted
about 20 degrees toward the sweep direction.
.04 in
(1 ~ 2 mm)
(1)
(1) Cable adjuster
ADJUSTING IDLING SPEED
2. You can avoid thrown debris by sweeping from your
left to the right.
3. Use a slow, deliberate action to cut heavy growth.
The rate of cutting motion will depend on the material
being cut. Heavy growth will require slower action than
will light growth.
(1) Idle adjusting screw
1. When the engine tends to stop frequently at idling
mode, turn the adjusting screw clockwise.
4. Never swing the unit so hard as you are in danger of
losing your balance or control of the unit.
2. When the cutting head keeps rotating after releasing
the trigger, turn the adjusting screw counter-clockwise.
5. Try to control the cutting motion with the hip rather
than placing the full workload on the arm and hands.
NOTE
6. Take precautions to avoid wire, grass and dead, dry,
long-stem weeds from wrapping around the head
shaft. Such materials can stall the head and cause
the clutch to slip, resulting in damage to the clutch
system if repeated frequently.
• Warm up the engine before adjusting the idling speed.
CUTTING WORK (LINE HEAD USAGE)
WARNING
ADJUSTING THE LINE LENGTH
• Your brush cutter is equipped with a semi- auto type
nylon line head that allows the operator to advance
the line without stopping the engine. When the line
becomes short, lightly tap the head on the ground
while running the engine at full throttle.
1. Always wear eye protection such as safety
goggles. Never lean over the rotating cutting head.
Rocks or other debris could be thrown into eyes
and face and cause serious personal injury.
• Each time the head is bumped, the line advances
about 25 mm. For better effect, tap the head on bear
ground or hard soil. Avoid bumping in thick, tall grass
as the engine may stall by overload.
2. Keep the cutting attachment guard in place at all
times when the unit is operated.
GB-12
Download from Www.Somanuals.com. All Manuals Search And Download.
BC2310DL
9. Maintenance
Every Every Every
25 50 100
hours hours hours
after after after
Before
use
System/components
Procedure
Note
fuel leaks, fuel spillage
fuel tank, air filter, fuel filter
wipe out
✔
✔
G
B
inspect/clean
see adjusting
idling speed
clean and readjust
plug gap
✔
replace, if necessary
replace carburetor
if necessary
GAP: .025 in (0.6 ~ 0.7 mm)
replace, if necessary
idle adjusting screw
spark plug
✔
✔
cylinder fins, intake air cooling vent clean
muffler, spark arrester, cylinder exhaust port clean
✔
✔
throttle lever, ignition switch
check operation
replace if
something’s wrong
grease
✔
✔
cutting parts
gear case
✔
screws/nuts/bolts
cutting attachment guard
tighten/replace
make sure to attach
✔
✔
✔
except adjusting screws
FUEL FILTER
• When the engine runs short of fuel supply, check the
fuel cap and the fuel filter for blockage.
WARNING
• Make sure that the engine has stopped and is cool
before performing any service to the machine.
Contact with moving cutting head or hot muffler
may result in a personal injury.
AIR FILTER
• The air filter, if clogged, will reduce the engine perfor-
mance. Check and clean the filter element in warm,
soapy water as required. Dry completely before in-
stalling. If the element is broken or shrunk, replace
with a new one.
(1) Fuel filter
(1) Air filter
GB-13
Download from Www.Somanuals.com. All Manuals Search And Download.
BC2310DL
9. Maintenance
SPARK PLUG
GEAR CASE
• Starting failure and misfiring are often caused by a
fouled spark plug. Clean the spark plug and check
that the plug gap is in the correct range. For a re-
placement plug, use the correct type specified by
ZENOAH.
• The reduction gears are lubricated by multipurpose,
lithium-based grease in the gear case. Supply new
grease every 25 hours of use or more often depend-
ing on the job condition.
• Remove the bolt opposit to the grease nipple before
installing new grease to arrange for old grease to exit.
0.6~0.7 mm
• REPLACEMENT PLUG IS A NGK BPMR7A.
INTAKE AIR COOLING VENT
WARNING
IMPORTANT
• Note that using any spark plug other than those des-
ignated may result in the engine failing to operate prop-
erly or in the engine becoming overheated and dam-
aged.
• To install the spark plug, first turn the plug until it is
finger tight, then tighten it a quarter turn more with a
socket wrench.
• Never touch the cylinder, muffler, or spark plugs
with your bare hands immediately after stopping
the engine. The engine can become very hot when
in operation, and doing so could result in severe
burns.
• When checking the machine to make sure that it
is okay before using it, check the area around the
muffler and remove any wood chips or leaves
which have attached themselves to the
brushcutter. Failing to do so could cause the muf-
fler to become overheated and that in turn could
cause the engine to catch on fire. Always make
sure that the muffler is clean and free of wood
chips, leaves, and other waste before use.
150 ~ 220 kgf-cm
TIGHTENING TORQUE:
(14.7 ~ 21.6 N.m.)
•
Check the intake air cooling vent and the area
around the cylinder cooling fins after every 25
hours of use for blockage, and remove any waste
which has attached itself to the brushcutter. Note
that it is necessary to remove the engine cover
shown in (MA5) in order to be able to view the up-
per part of the cylinder.
MUFFLER
WARNING
IMPORTANT
• Inspect periodically, the muffler for loose fasteners,
any damage or corrosion. If any sign of exhaust leak-
age is found, stop using the machine and have it re-
paired immediately.
• Note that failing to do so may result in the engine
catching on fire.
• If waste gets stuck and causes blockage around the
intake air cooling vent or between the cylinder fins, it
may cause the engine to overheat, and that in turn
may cause mechanical failure on the part of the
brushcutter.
(1) Intake air cooling vent
GB-14
Download from Www.Somanuals.com. All Manuals Search And Download.
BC2310DL
9. Maintenance
PROCEDURES TO BE PERFORMED AFTER
EVERY 100 HOURS OF USE
4. Wind up the line in the correct direction as indicated
on the spool.
G
B
1. Remove the muffler, insert a screwdriver into the vent,
and wipe away any carbon buildup. Wipe away any
carbon buildup on the muffler exhaust vent and cylin-
der exhaust port at the same time.
5. Hook each end of the line in the slot on the edge of
the spool, and then put the ends through the eyelets
on the housing. Make sure that the spring and the
washers are in place.
2. Tighten all screws, bolts, and fittings.
3. Check to see if any oil or grease has worked its way
in between the clutch lining and drum, and if it has,
wipe it away using oil-free, lead-free gasoline.
REFILLING TRIMMING LINE
1. For replacement line, use a diameter of
2.4 mm. The spool is capable for a line upto
6 m on the 4" head. Avoid using a larger line as it may
cut down the trimming performance.
6. While holding the spool against the housing, pull the
line ends to release them from the slot.
WARNING
For safety reasons, do not use metal reinforced line.
2. Pinch the slotted area on the both sides of the spool
housing to unhook the bottom cap.
7. Line up the slot on the bottom cap with the hook on
the housing, press the cap against the housing until it
clicks.
3. Take out the spool and pull off the old line. Put one
end of new line through the spool holes and pull it
until the length is equal between each part of the line.
10. Storage
Aged fuel is one of major causes of engine starting fail-
ure. Before storing the unit, empty the fuel tank and run
the engine until it uses all the fuel left in the fuel line and
the carburetor. Store the unit indoor taking necessary
measures for rust prevention.
11. Disposal
When disposing your machine, fuel or oil for the machine,
be sure to allow your local regulations.
GB-15
Download from Www.Somanuals.com. All Manuals Search And Download.
BC2310DL
12. Troubleshooting guide
Case 1. Starting failure
CHECK
fuel tank
fuel filter
PROBABLE CAUSES
→ incorrect fuel
→ fuel filter is clogged
ACTION
→ drain it and use correct fuel
→ clean
carburetor adjustment screw → out of normal range
→ adjust to normal range
→ clean/dry
→ correct (GAP: 0.6 ~ 0.7 mm)
→ retighten
sparking (no spark)
spark plug
→ spark plug is fouled/wet
→ plug gap is incorrect
→ disconnected
Case 2. Engine starts but does not keep running/hard re-starting
CHECK
PROBABLE CAUSES
ACTION
fuel tank
→ incorrect fuel or staled fuel → drain it and use correct fuel
carburetor adjustment screw → out of normal range
muffler, cylinder (exhaust port) → carbon is built-up
→ adjust to normal range
→ wipe away
→ wash
air cleaner
→ clogged with dust
→ clogged with dust
cylinder fin, fan cover
→ clean
When your unit seems to need further service, please consult with our ZENOAH service shop in your area.
Limited warranty
Should any failure occur on the product under normal oper-
ating conditions within the applicable warranty period, the
failed part will be replaced or repaired free of charge by a
ZENOAH authorized dealer.
WARRANTY MAINTENANCE OR REPAIRS, AND SHALL
NOT REDUCE THE WARRANTY OBLIGATION OF THE
COMPANY.
THE COMPANY IS LIABLE FOR DAMAGES TO OTHER
ENGINE COMPONENTS CAUSED BY THE FAIRURE OF A
WARRANTED PARTS STILL UNDER WARRANTY.
WARRANTY PERIOD: 1 year (6 months if used profession-
ally, and 30 days if used for rental purpose) from the date of
initial purchase.
THE WARRANTY DOES NOT APPLY TO THOSE UNITS
WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF IN-
STRUCTION LISTED IN THE OWNER/OPERATOR MANUAL
FOR PROPER USE AND MAINTENANCE OF THE UNITS
ACCIDENT MISHANDLING, ALTERATION, ABUSE, IM-
PROPER LUBRICATION, USE OF ANY PARTS OR ACCES-
SARIES OTHER THAN THOSE SPECIFIED BY THE COM-
PANY, OR OTHER CAUSES BEYOND THE COMPANY’S
CONTROL.
THE PURCHASER SHALL BEAR COSTS OF TRANS-
PORTING THE UNIT TO AND FROM THE ZENOAH DEALER.
THE PURCHASER SHALL NOT BE CHARGED FOR DIAG-
NOSTIC LABOR WHICH LEADS TO THE DETERMINATION
THAT A WARRANTED PART IS DEFECTIVE, IF THE DIAG-
NOSTIC WORK IS PERFORMED AT THE ZENOAH DEALER.
THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE
PERFORMANCE OF THE REQUIRED MAINTENANCE AS
DEFINED BY THE MANUFACTURER IN THE OWNER/OP-
ERATOR MANUAL.
THIS WARRANTY DOES NOT COVER THOSE PARTS RE-
PLACED BY NORMAL WEAR OR HARMLESS CHANGES
IN THEIR APPEARANCE.
ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR
REPLACEMENT AS REQUIRED MAINTENANCE, OR
WHICH IS SCHEDULED ONLY FOR REGULAR INSPECTION
TO THE EFFECT OF REPAIR OR “REPLACE AS NECES-
SARY” SHALL BE WARRANTED FOR THE WARRANTY PE-
RIOD. ANY WARRANTED PART WHICH IS SCHEDULED
FOR REPLACEMENT AS REQUIRED MAINTENANCE
SHALL BE WARRANTED FOR THE PERIOD OF TIME UP
TO THE FIRST SCHEDULED REPLACEMENT POINT FOR
THE PART.
THERE ARE NO OTHER EXPRESS WARRANTIES.
IMPLIED WARRANTIES INCLUDING THOSE OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PUR-
POSE ARE LIMITED TO TWO (2) YEARS OF HOME USE
[ONE (1) YEAR FOR ANY OTHER USE] FROM THE ORIGI-
NAL DELIVERY DATE.
LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGE UNDER ANY AND ALL WARRANTIES ARE
EXCLUDED.
ANY REPLACEMENT PART THAT IS EQUIVALENT IN PER-
FORMANCE AND DULABILITY MAY BE USED IN NON-
IF YOU NEED TO OBTAIN MORE INFORMATION, PLEASE
C A L L Y O U R N E A R E S T S E R V I C E C E N T E R ,
OR CHECK PLEASE ZENOAH WEB SITE
GB-16
Download from Www.Somanuals.com. All Manuals Search And Download.
|