DA402
Stripe® Series Direct Thermal Printer
User's
Guide
Rev. 2
Customer order # 52005L
Manufacturer part # 52005LB
Download from Www.Somanuals.com. All Manuals Search And Download.
I have determined that the Zebra printers identified as the
Stripe® Series
DA402 and T402
manufactured by:
Zebra Technologies Corporation
333 Corporate Woods Parkway
Vernon Hills, Illinois 60061-3109 U.S.A.
have been shown to comply with the applicable technical standards of the FCC
for Home, Office, Commercial, and Industrial use
if no unauthorized change is made in the equipment,
and if the equipment is properly maintained and operated.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Introduction
Hello! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Unpacking and Inspection . . . . . . . . . . . . . . . . . . . . . . . . 2
Reporting Damage . . . . . . . . . . . . . . . . . . . . . . . . . . 2
DC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Printer Overview (illustration) . . . . . . . . . . . . . . . . . . . . . 4
Getting Ready to Print
Loading the Media. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Tear-Off Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Peel-Off Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Cutter Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Fanfold Media . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Auto Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Operator Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Feed Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Printing a Test Label . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Hooking Up the Printer and Computer. . . . . . . . . . . . . . . . . 20
Serial (RS-232) Interface Requirements . . . . . . . . . . . . . . 20
Parallel Interface Requirements . . . . . . . . . . . . . . . . . . 21
Serial and Parallel Cabling Requirements . . . . . . . . . . . . . 21
Communicating with the Printer . . . . . . . . . . . . . . . . . . . . 22
Via the Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . 22
Via the Parallel Port. . . . . . . . . . . . . . . . . . . . . . . . . 22
Using ZPL II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Adjusting the Print Width . . . . . . . . . . . . . . . . . . . . . . . 23
Adjusting the Print Darkness. . . . . . . . . . . . . . . . . . . . . . 23
Adjusting the Print Speed . . . . . . . . . . . . . . . . . . . . . . . 23
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
What the Status LED is Telling You. . . . . . . . . . . . . . . . . . 25
Print Quality Problems . . . . . . . . . . . . . . . . . . . . . . . . . 26
Manual Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Troubleshooting Tests . . . . . . . . . . . . . . . . . . . . . . . . . 29
Printing a Configuration Label . . . . . . . . . . . . . . . . . . . 29
Recalibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Resetting the Factory Default Values. . . . . . . . . . . . . . . . 30
Communications Diagnostics. . . . . . . . . . . . . . . . . . . . 30
Feed Button Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Maintenance
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Replacing the Printhead . . . . . . . . . . . . . . . . . . . . . . . . 36
Removing the Printhead . . . . . . . . . . . . . . . . . . . . . . 36
Installing the Printhead . . . . . . . . . . . . . . . . . . . . . . . 38
Specifications
Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Label/Tag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Font/Bar Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Physical/Environmental/Electrical . . . . . . . . . . . . . . . . . . . 43
Agency Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Serial (RS-232) Connector Technical Information . . . . . . . . . . 45
Interconnecting to DTE Devices . . . . . . . . . . . . . . . . . . 45
Interconnecting to DCE Devices . . . . . . . . . . . . . . . . . . 45
Parallel Interface Technical Information. . . . . . . . . . . . . . . . 48
Index
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Hello!
Thank you for choosing the Zebra DA402 Printer. This rugged little
printer is certain to become a productive and efficient addition to your
workplace!
n
This user’s guide provides the information you will need to operate and
maintain the printer.
n
To create and print label formats, take a look at the ZPL II Programming
Guide. If one was not ordered with your printer, simply call your
NOTE: Many printer settings may also be controlled by your
printer’s driver or label preparation software. Refer to the driver
or software documentation for more information.
What’s in the Box
Printer
Power
Supply
Quick
Reference
Guide
Product
Support Services
Brochure
User’s
Guide
Sample
Roll of Media
Test
Label
CD-Rom
Registration
Card
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking and Inspection
Inspect the printer for possible shipping damage:
n
Check all exterior surfaces for damage.
n
Raise the top cover (refer to “Loading the Media” on page 5) and inspect
the media compartment for damage.
In case shipping is required, save the carton and all packing material.
Reporting Damage
If you discover shipping damage:
n
Immediately notify and file a damage report with the shipping company.
Zebra Technologies Corporation is not responsible for any damage
incurred during shipment of the printer and will not cover the repair of
this damage under its warranty policy.
n
Keep the carton and all packing material for inspection.
n
Notify your authorized reseller.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: NEVER OPERATE THE PRINTER AND POWER
SUPPLY IN AN AREA WHERE THEY CAN GET WET.
SERIOUS PERSONAL INJURY COULD RESULT!
DC Power Supply
Refer to Figure 1.
1. The DC power supply has a barrel connector on one end that must be
inserted into the power supply receptacle on the back of the printer.
2. Insert the separate AC power cord into the power supply.
3. Plug the other end of the cord into an appropriate AC electrical outlet.
Plug
Varies by
Country
AC
Power
Cord
Barrel
Connector
Power
Switch
Power
Supply
Power
Supply
Receptacle
Figure 1
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Overview
Feed
Button
Status
LED
Tear Bar
Printhead
Release
Lever
Release
Lever
Lock-down Screw
Media Guide Adjuster
Media
Hangers
Platen Roller
Media Guides
Peel-Off Option
Cutter Option
Peel
Bar
Peel Roller
Cutter Unit
Figure 2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready to Print
Loading the Media
You can operate this printer in three different modes: tear-off, peel-off, or
with a cutter.
n
Tear-off mode allows you to tear off each label (or a strip of labels) after
it is printed.
n
In peel-off mode, the backing material is peeled away from the label as it
is printed. After this label is removed, the next one is printed.
n
In cutter mode, the printer automatically cuts the label after it is printed.
Tear-Off Mode
1. Unlatch the top cover by pulling the two green release levers toward
you (refer to Figure 3). Then, lift the top cover to expose the media
compartment.
Release
Lever
Release
Lever
Figure 3
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Separate and hold open the media hangers (refer to Figure 4).
3. Place the media roll onto the media hangers, ensuring that it is tightly
wound (refer to Figure 5).
NOTE: Refer to Figure 6. If you are using labels, make sure the
media unwinds from the top of the roll. Tags unwind from the
bottom of the roll.
Media
Hanger
Media
Hanger
Figure 4
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 5
Tags
Labels
Figure 6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Refer to Figure 7. Thread the media through the media guides.
NOTE: If the media guides must be changed to accommodate the
width of the media, turn the green media guide adjuster (refer to
Figure 7). The media guides should just touch, but not restrict, the
edges of the media.
5. Close the top cover and turn on the printer or press the feed button if
the printer is already on (see “Auto Calibration” on page 18 for more
information).
Wide Media
Media
Narrow Media
Guides
Media Guide Adjuster
Figure 7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Peel-Off Mode (optional)
1. Unlatch the top cover by pulling the two green release levers toward
you (refer to Figure 8). Then, lift the top cover to expose the media
compartment.
Release
Lever
Release
Lever
Figure 8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Separate and hold open the media hangers (refer to Figure 9).
3. Place the media roll onto the media hangers, making sure it is tightly
wound (refer to Figure 10).
4. Open the peel-off unit by pulling down on its textured top surface (refer
to Figure 11).
5. Activate the peel-off unit by moving the peel-off switch to the left
(refer to Figure 11 inset).
NOTE: When not operating the printer in peel-off mode, always
deactivate the peel-off unit by moving the peel-off switch to the
right.
6. Remove approximately 6” (152 mm) of labels from the label backing.
Media
Hanger
Media
Hanger
Figure 9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 10
Peel-off Switch
ON OFF
Figure 11
11
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Refer to Figure 12. Thread the label backing through the media guides
and over the peel bar.
NOTE: If the media guides must be changed to accommodate the
width of the media, turn the green media guide adjuster (refer to
Figure 12). The media guides should just touch, but not restrict,
the edges of the media.
Wide Media
Media
Narrow Media
Guides
Peel Bar
Media Guide Adjuster
Figure 12
12
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Thread the label backing between the black platen roller and white peel
roller until it comes out of the slot beneath the peel-off unit (refer to
Figure 13).
9. Close the peel-off unit by pushing in on its smooth side surface.
10. To remove any slack, rewind media onto the roll.
11. Close the top cover and turn on the printer or press the feed button if
the printer is already on (see “Auto Calibration” on page 18 for more
information).
Platen
Roller
Peel Bar
Peel
Roller
Slot
Figure 13
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Cutter Mode (optional)
NOTE: The cutter is designed to cut through paper labels or the
backing between labels, not the adhesive backing of the label.
Adhesive build-up on the cutter blade may cause the cutter to jam.
1. Unlatch the top cover by pulling the two green release levers toward
you (refer to Figure 14). Then, lift the top cover to expose the media
compartment.
2. Separate and hold open the media hangers (refer to Figure 15).
3. Place the media roll onto the media hangers, ensuring that it is tightly
wound (refer to Figure 16).
Release
Lever
Release
Lever
Figure 14
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Media
Hanger
Media
Hanger
Figure 15
Figure 16
15
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Refer to Figure 17. Thread the media through the media guides.
NOTE: If the media guides must be changed to accommodate the
width of the media, turn the green media guide adjuster (refer to
Figure 17). The media guides should just touch, but not restrict,
the edges of the media.
5. Refer to Figure 17. Thread the media through the cutter unit.
6. Close the top cover and turn on the printer or press the feed button if
the printer is already on (see “Auto Calibration” on page 18 for more
information).
Wide Media
Media
Narrow Media
Guides
Media Guide Adjuster
Figure 17
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Fanfold Media
Fanfold media loads from the outside of the printer. Refer to Figure 18.
1. Thread the media through the access slot in the back of the printer.
2. Separate and hold open the media hangers.
3. Lock the media hangers in position by tightening the screw located on
the right media hanger.
CAUTION: Do not overtighten the screw! Overtightening
could pierce the case and damage the printer’s electronics!
4. Thread the media through the media guides.
NOTE: If the media guides must be changed to accommodate the
width of the media, turn the green media guide adjuster. Media
guides should just touch, but not restrict, the edges of the media.
5. Close the top cover and turn on the printer or press the feed button if
the printer is already on (see “Auto Calibration” on page 18 for more
information).
Media
Hangers
Lock-down
Screw
Media
Guide
Adjuster
Access
Slot
Media
Guides
Figure 18
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Calibration
NOTE: If you are using pre-printed labels, pre-printed label
backing, or continuous media, see “Manual Calibration” on
page 28.
An auto calibration is performed when the printer is turned on (if media is
loaded) or after a media error is cleared. When it is auto calibrating, the
printer sets the sensor levels for, and determines the length of, the label you
are using.
If the status LED flashes red, refer to “Manual Calibration” on page 28.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operator Controls
Refer to Figure 19.
Power Switch
n
Press to turn on and turn off the printer.
CAUTION: The power should be turned off before connecting
or disconnecting the communications and power cables.
Feed Button
n
Forces the printer to feed one blank label.
n
Takes the printer out of a “pause” condition. (The printer is put into
“pause” by either a ZPL II command or an error condition.) See “What
the Status LED is Telling You” on page 25.
n
Used for printer setup and status (see “Feed Button Modes” on page 31).
Status LED
n
Functions as a printer operational indicator (see “What the Status LED is
Telling You” on page 25).
Feed
Button
Status
LED
Power
Switch
Figure 19
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing a Test Label
Before you connect the printer to your computer, make sure that the printer
is in proper working order. You can do this by printing a configuration
label:
1. Make sure the media is properly loaded and the top cover of the printer
is closed. Then, turn the printer power on if you have not already done
so.
2. When the status LED is solid green, press and hold the feed button until
the status LED flashes once.
3. Release the feed button. A configuration label will print.
If you cannot get this label to print, refer to Troubleshooting.
Hooking Up the Printer and Computer
CAUTION: The power supply barrel connector must be
inserted into the power supply receptacle on the back of the
printer before connecting or disconnecting the
communications cables. (If necessary, refer to Figure 1.)
This printer comes with both a nine-pin Electronics Industries Association
(EIA) RS-232 serial data interface and an IEEE 1284-compliant
bidirectional parallel data interface. In either case, you must supply the
required interface cable for your application.
CAUTION: This printer complies with FCC “Rules and
Regulations,” Part 15, for Class B Equipment, using fully
shielded six-foot data cables. Use of longer cables or
unshielded cables may increase radiated emissions above the
Class B limits.
Serial (RS-232) Interface Requirements
The required cable must have a nine-pin “D” type (DB-9P) male connector
on one end, which is plugged into the mating (DB-9S) serial port located on
the back of the printer (refer to Figure 20). The other end of this signal
interface cable connects to a serial port at the host computer. Depending on
the specific interface requirements, this will most likely be a null modem
cable.
For technical and pinout information, refer to page 45.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Parallel Interface Requirements
The required cable (IEEE 1284-compliant is recommended) must have a
standard 36-pin parallel connector on one end, which is plugged into the
parallel port located on the back of the printer (refer to Figure 20). The
other end of the parallel interface cable connects to the printer connector at
the host computer.
For pinout information, refer to page 48.
Serial and Parallel Cabling Requirements
Data cables must be of fully shielded construction and fitted with metal or
metalized connector shells. Shielded cables and connectors are required to
prevent radiation and reception of electrical noise.
To minimize electrical noise pickup in the cable:
n
Keep data cables as short as possible (6’ [1.83 m] recommended).
n
Do not tightly bundle the data cables with power cords.
n
Do not tie the data cables to power wire conduits.
Connects to
Serial Port on
Host Computer
Serial
Port
Parallel
Port
Connects to
Parallel Port on
Host Computer
Figure 20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Communicating with the Printer
Via the Serial Port
Serial communications between the printer and the host computer can be set
by either autobaud synchronization or the ^SC command.
Autobaud
Autobaud synchronization allows the printer to automatically match the
communication parameters of the host computer. To autobaud:
1. Press and hold the feed button until the green status LED flashes once,
twice, and then three times.
2. While the status LED flashes, send a ZPL II format to the printer.
3. When the printer and host are synchronized, the LED changes to solid
green. (No labels will print during autobaud synchronization.)
^SC Command
Use the Set Communications (^SC) command to change the
communications settings on the printer.
1. With the host computer set at the same communications settings as the
printer, send the ^SC command to change the printer to the desired
settings.
2. Change the host computer settings to match the new printer settings.
Refer to the ZPL II Programming Guide for more information about this
command.
Setting the Communications Parameters
To reset the communications parameters on the printer to the factory
defaults (9600 baud, 8 bit word length, no parity, 1 stop bit, and
XON/XOFF), do the following:
1. Press and hold the feed button until the green status LED flashes once,
twice, and then three times.
2. While the status LED rapidly flashes yellow and green, press the feed
button.
Via the Parallel Port
Typically, no setup is required once the cable is plugged in. If you should
encounter any problems, consult the user’s guide that came with your
computer.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using ZPL II
For detailed information about creating labels using ZPL II, refer to the
Adjusting the Print Width
Print width must be calibrated when:
n
You are using the printer for the first time.
n
There is a change in the width of the media.
Print width may be set by way of the five-flash sequence in “Feed Button
Modes” (see page 31) or refer to the Print Width (^PW) command (consult
your ZPL II Programming Guide).
Adjusting the Print Darkness
The relative darkness setting is controlled by either the six-flash sequence in
“Feed Button Modes” (see page 31) or the Set Darkness (~SD) ZPL II
command (follow the instructions in the ZPL II Programming Guide).
Adjusting the Print Speed
Print quality is affected by print speed and the media you are using. Only
by experimenting will you find the optimal mix for your application.
If you find that the print speed needs to be adjusted, refer to the Print Rate
(^PR) command in the ZPL II Programming Guide.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
What the Status LED is Telling You
Status LED
Condition and Color
Printer
Status
For a Resolution,
Refer to:
Off
Solid Green
Off
On
1
2
3
4
5
6
7
8
Flashing Yellow
Stopped
Flashing Green
Normal Operation
Stopped
Flashing Red
Double Flashing Green
Solid Yellow
Paused
Various
Alternately Flashing Green and Red
Needs Service
RESOLUTIONS:
1. The printer is not receiving power.
n
Have you turned on the printer power?
n
Check power connections from the wall outlet to the power supply,
and from the power supply to the printer.
2. The printer is on and in an idle state.
3. The printer has failed its power on self test (POST).
n
If this error occurs right after you turn on the printer, contact an
authorized reseller for assistance.
There is a shortage of memory.
n
If this error occurs after you have been printing, turn the printer
power off and on. Then, resume printing.
4. The printer is receiving data.
n
As soon as all of the data has been received, the status LED will
turn green; then, the printer will automatically resume operation.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
5. The media is out.
n
Load a roll of media, following the instructions in “Loading the
Media” on page 5. Then, press the feed button to resume printing.
The printhead is open.
n
Close the top cover. Then, press the feed button to resume printing.
The cutter is jammed.
n
Turn off the printer and remove any jammed labels from the cutter
unit. Then, turn on the printer to resume printing.
6. The printer is paused.
n
Press the feed button to resume printing.
7. The printhead is under temperature.
n
Continue printing while the printhead reaches the correct operating
temperature.
The printhead is over temperature.
n
Printing will stop until the printhead cools to an acceptable printing
temperature. When it does, the printer will automatically resume
operation.
8. FLASH memory is not programmed.
n
Return the printer to an authorized reseller.
Print Quality Problems
No print on the label.
n
Make sure the correct media (direct thermal) is loaded. Try this:
Quickly rub your nail or a blunt object over the label surface. If it does
not produce dark marks, the wrong media (thermal transfer) is loaded.
n
Is the media loaded correctly? Follow the instructions in “Loading the
Media” on page 5.
The printed image does not look right.
n
The printhead is dirty. Clean the printhead according to the instructions
on page 33.
n
The printhead is under temperature.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
n
Adjust the print darkness and/or print speed. Refer to the six-flash
sequence in “Feed Button Modes” on page 31, or the ^PR and ~SD
commands in the ZPL II Programming Guide.
n
The media being used is incompatible with the printer. Be sure to use
the recommended media for your application, and always use
Zebra-approved labels and tags.
There are long tracks of missing print (blank vertical
lines) on several labels.
n
The printhead is dirty. Clean the printhead according to the instructions
on page 33.
n
The printhead elements are damaged. Replace the printhead (see
“Replacing the Printhead” on page 36).
The printing does not start at the top of the label, or
misprinting of one to three labels.
n
The media may not be threaded under the media guides. Refer to
“Loading the Media” on page 5.
n
The printer needs to be calibrated. Refer to “Auto Calibration” on
page 18.
n
The correct media sensor may not be activated. Manual calibration
selects the media sensing method for the labels being used (refer to the
^MN command in the ZPL II Programming Guide).
n
Verify that the Label Top (^LT) command is correctly set for your
application (consult the ZPL II Programming Guide).
A label format was sent to, but not recognized by, the
printer.
n
Is the printer in pause mode? If so, press the feed button.
n
If the status LED is on or flashing, refer to “What the Status LED is
Telling You” on page 25.
n
Make sure the data cable is correctly installed.
n
A communications problem has occurred. First, make sure that the
correct communications port on the computer is selected. Next, verify
that the same handshaking is in use by both the printer and the computer.
Then, ensure that the baud rates of the printer and the computer match.
Refer to “Communicating with the Printer” on page 22.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Calibration
Manual calibration is recommended whenever you are using pre-printed
labels (or label backing) or if the printer will not correctly auto calibrate.
1. Turn on the printer power.
2. Remove approximately 4” (102 mm) of labels from a section of
backing material. Load the media so that only the backing material is
threaded through the printer and under the printhead.
3. Press and hold the feed button until the green status LED flashes once,
then twice. Release the feed button.
4. The printer will set the media sensor for the label backing being used.
After it is done making this adjustment, the roll will automatically feed
until a label is positioned at the printhead.
5. A profile of the media sensor settings (similar to the example in
Figure 21) will print. Upon completion, the printer will save the new
settings in memory and the printer is ready for normal operation.
6. Press the feed button. One entire blank label will feed. If this does not
happen, try defaulting (refer to the four-flash sequence in “Feed Button
Modes” on page 31) and recalibrating the printer.
NOTE: Performing a manual calibration disables the auto
calibration function. To return to auto calibration, default the
printer (see the four-flash sequence in “Feed Button Modes” on
page 31).
Figure 21
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Tests
Printing a Configuration Label
To print out a listing of the printer’s current configuration (an example is
shown in Figure 22), refer to the one-flash sequence in “Feed Button
Modes” on page 31.
Recalibration
Recalibrate the printer if it starts to display unusual symptoms, such as
skipping labels. See “Auto Calibration” on page 18.
Figure 22
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Resetting the Factory Default Values
Sometimes, resetting the printer to the factory defaults solves some of the
problems. Follow the four-flash sequence instructions in “Feed Button
Modes” on page 31.
Communications Diagnostics
If there is a problem transferring data between the computer and printer, try
putting the printer in the communications diagnostics mode. The printer
will print the ASCII characters and their respective hexadecimal values (a
sample is shown in Figure 23) for any data received from the host
computer. To find out how, refer to the power off mode procedure in “Feed
Button Modes” on page 31.
Figure 23
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Feed Button Modes
Power Off Mode (Communications Diagnostics Mode)
With the printer power off, press and hold the feed button while you turn on the
power. The printer prints out a listing of its current configuration (see Figure 22).
After printing the label, the printer will automatically enter a diagnostic mode in
which the printer prints out a literal representation (see Figure 23) of all data
subsequently received. To exit the diagnostic mode and resume printing, turn off
and then turn on the printer.
Power On Modes
With the printer power on and top cover closed, press and hold the feed button for
several seconds. The green status LED will flash a number of times in sequence.
The explanation at the right (Action) shows what happens when you release the key
after the specific number of flashes.
Flash
Sequence
Action
*
A configuration label prints.
*
**
The media sensor calibrates and a media sensor profile prints (see
“Manual Calibration” on page 28).
To reset the communication parameters: Press and release the feed
button while the LED rapidly flashes yellow and green. The serial
communication parameters reset to 9600 baud, 8 bits per character,
no parity, 1 stop bit, and XON/XOFF.
*
**
***
For autobaud synchronization: Send a ZPL II format to the printer
while the LED rapidly flashes yellow and green. When the printer and
host are synchronized, the LED changes to solid green. NOTE: No
labels will print during autobaud synchronization.
*
**
***
****
Resets the factory defaults, auto calibrates, and saves settings into
memory.
*
**
***
****
*****
The print width calibrates. While the status LED alternately flashes
green and yellow, a series of stacking rectangles print on the label.
When the rectangle prints to the outer edges of the label, press and
release the feed button. The label width and current communication
parameters will be saved into memory.
*
**
***
****
*****
******
The print darkness calibrates. A series of nine samples print, starting
with the lightest and ending with the darkest image. When the desired
print darkness is achieved, press and release the feed button. The
print darkness will be saved into memory.
If the feed button remains pressed after a 7-flash sequence, the printer will ignore
the button when it is released.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning
CAUTION: Use only the cleaning agents indicated. Zebra
Technologies Corporation will not be responsible for damage
caused by any other cleaning materials used on this printer.
If necessary, refer to Figure 2 for part locations.
Area
Method
Interval
After allowing the printhead to cool for approximately one
minute, use 70% isopropyl alcohol on a cotton swab to
clean the print elements from end to end (the print
elements are located in the thin gray line on the printhead).
NOTE: You do not have to turn off the printer to do this.
After
Printhead
If print quality has not improved after performing this
procedure, try cleaning the printhead with
Save-a-Printhead cleaning film. This specially coated
material removes contamination buildup without
damaging the printhead. Call your authorized reseller for
more information.
every five
rolls of
media
Manually rotate the platen roller. Clean it thoroughly with
70% isopropyl alcohol and a cotton swab or lint-free cloth.
Platen roller
Peel bar
Tear bar
Cutter
Clean it thoroughly with 70% isopropyl alcohol and a
cotton swab.
As
needed
Clean it thoroughly with 70% isopropyl alcohol and a
cotton swab.
As
needed
Turn off the printer power. Use tweezers to remove the
media.
As
needed
As
needed
Exterior
Interior
Water-dampened cloth
Brush/air blow
As
needed
Lubrication
CAUTION! No lubricating agents of any kind should be used
on this printer! Some commercially available lubricants, if
used, will damage the finish and the mechanical parts inside
the printer.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
9
7
8
Figure 24
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Refer to Figure 24.
Item
Number
Part
Number
Description
Feed Switch Assembly (set of 3)
Printhead and Latch Assembly
Printhead Assembly
1
2
3
4
105910-004
105910-003
105910-010
105910-011
105910-001
105910-002
105910-005
105910-012
105910-013
105910-006
105910-007
52050M
Media Sensor PCB Assembly (set of 3)
Platen Roller Kit, Standard (set of 3)
Platen Roller Kit, Linerless
5
6
Front Bezel, Standard (set of 10)
Front Bezel, Peel-Off (set of 5)
Peel-Off Sensor PCB Assembly (set of 3)
Base Housing (set of 3)
7
8
9
Rubber Foot Kit (set of 24)
Main Logic Board Kit, Maintenance
Stepper Motor, (set of two)
105910-009
105903-040
105950-014
105950-015
105950-030
105950-029
105910-028
52051
Power Supply Assembly (90-264 VAC, 47-63 Hz)
Power Cord, 110V (set of 5)
Power Cord, 230V European (set of 5)
Power Cord, 230V UK (set of 5)
Power Cord, 230V Australian (set of 5)
Cutter
Not
shown:
4M FLASH Memory Option Assembly
8M FLASH Memory Option Assembly
4M FLASH Memory w/Real Time Clock Option Assembly
8M FLASH Memory w/Real Time Clock Option Assembly
User’s Guide
52052
52053
52054
52005L
Quick Reference Guide
52006L
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Printhead
Removing the Printhead
1. Turn printer power off and unplug the printer.
2. Refer to Figure 25. Remove the four screws that secure the printhead
and latch assembly to the top cover.
3. Refer to Figure 26. Slide the tension bar all the way to the right in its
mounting bracket (1). Then, while gently pressing on the opposite
mounting bracket (2), lift and remove the tension bar (3).
4. Refer to Figure 27. Remove both printhead wire harness connectors
from their receptacles.
5. Refer to Figure 27. Remove the two screws and washers that secure
the printhead to the printhead bracket. Then, lift the lip on the front of
the printhead bracket to remove the printhead.
Printhead and Latch Assembly
Top Cover
Screws (4)
Figure 25
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Tension Bar
Tension Bar
Mounting
Bracket
3
Tension Bar
Mounting
Bracket
1
2
Figure 26
Screw
and
Washer
Screw
and
Washer
Connector
Connector
Receptacle
(shown hidden)
Receptacle
(shown hidden)
Printhead
Bracket Lip
Printhead
Figure 27
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Printhead
1. Ensure that the printer is turned off and unplugged.
2. Refer to Figure 28. Route the two printhead wire harness connectors as
shown. Then, insert the connectors into their receptacles.
3. Insert the printhead into the printhead bracket.
4. Refer to Figure 29. Reinstall the two screws and washers that secure
the printhead to the printhead bracket.
NOTE: The green grounding cable, which attaches to the feed
switch assembly PC board, must also be secured by one of the
screws.
5. Refer to Figure 30. Insert one end of the tension bar into its mounting
bracket (1). Then, gently push down on the opposite end of the tension
bar until it locks into place (2).
NOTE: Make sure the “V” of the tension bar fits into the notch in
the printhead bracket.
6. Insure that all cables are properly dressed between the printhead and
latch assembly and the top cover.
7. Reinstall the four screws that secure the printhead and latch assembly
to the top cover. Then, plug in the printer and turn on the power.
Connector
Connector
Receptacle
(shown hidden)
Receptacle
(shown hidden)
Printhead
Figure 28
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Green
Grounding
Cable
Screw
and
Washer
Screw
and
Washer
Printhead
Printhead
Bracket
Figure 29
Tension Bar
2
1
“V” of Tension Bar
Printhead
Bracket
Notch
Figure 30
39
Download from Www.Somanuals.com. All Manuals Search And Download.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
NOTE: Printer specifications are subject to change without
notice.
Printing Specifications
Print Density
Print Speed
203 dots/inch (8 dots/mm)
1.5” (38 mm), 2” (51 mm), and 2.5” (64 mm) per second
1” to 4.09” (25.4 mm to 104 mm)
Print Width
Print Length
1” to 2.25” (25.4 mm to 57 mm) for tag stock
.005” to 22” (.125 mm to 559 mm) with standard memory
Registration
Tolerance
Horizontal: +/- 0.0591” (1.5 mm)
Vertical: +/- 0.0393” (1 mm)
FLASH Memory
(User Available)
1 MB
1 MB
DRAM Memory
(User Available)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Label/Tag Specifications
1” to 4.25” (25.4 mm to 108 mm)
Label/Tag Width
Label/Tag Length
Interlabel Gap
1” to 2.25” (25.4 mm to 57 mm) for tag stock
0.5” to 22” (13 mm to 559 mm) with standard memory
0.08” to 0.16” (2 mm to 4 mm)
0.118” (3 mm) recommended
.003” to .007” (.08 mm to .18 mm)
Label/Tag Thickness
.003” to .0053” (.08 mm to .135 mm) for cutter option
Max. Outer
Label
5” (127 mm)
Diameter
Roll
Size
Inner Core
1” (25.4 mm) or 1.5” (38 mm)
ü Use Zebra-brand direct thermal media that is outside
wound. Media may be reflective (black mark) sensing
or transmissive sensing, die-cut, notched, or
continuous.
ü For die-cut labels, use only full auto dies.
ü Notched media must have a 0.5” (13 mm) wide x
0.094” (2.4 mm) long cutout located in the center of the
roll. The reflective media black marks must be located
in the center of the roll.
Media
Requirements
Minimum Black Mark Dimensions:
ü Mark width: 0.5” (13 mm) centered and perpendicular
to the edge of the media.
ü Mark length: 0.094” (2.4 mm) parallel to the bottom
edge of the media.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Font/Bar Code Specifications
ü CG Triumvirate Bold Condensed scalable smooth (0)
ü Zebra fonts A-H, GS, P-V
Fonts Available
ü IBM Code Page 850 International Symbols
ü Codabar (supports ratios
of 2:1 to 3:1)
ü Industrial 2 of 5
ü Standard 2 of 5
ü Code 11
ü Interleaved 2 of 5
(supports ratios of 2:1 to
3:1, Modulus 10 Check
Digit)
ü Code 128/USD 8 (supports
serialization in all subsets
and UCC Case Codes)
Bar Codes
Available (1D)
ü Code 39 (supports ratios
of 2:1 to 3:1)
ü LOGMARS
ü MSI
ü Code 93
ü Plessey
ü EAN 8/JAN 8
ü EAN 13/JAN 13
ü EAN 14/UPC-A
ü POSTNET
ü UPC-E
ü UPC/EAN Extensions
ü Codablock
ü Code 49
ü MicroPDF417
ü PDF 417
Bar Codes
Available (2D)
ü Data Matrix
ü MaxiCode
ü QRcode
Rotation Angles
0°, 90°, 180°, and 270°
Physical/Environmental/Electrical
Specifications
Physical Size (L x W x H)
8.5” x 7.6” x 6.6”
3 lbs.
216 mm x 193 mm x 167 mm
1.4 kg.
Printer
Weight
Shipping
9 lbs.
4.1 kg.
Operating
40° to 105° F
-40° to 140° F
5° to 41° C
Temperature
Range
Storage
-40° to 60° C
Operating
Relative
10% to 90% (non-condensing)
Humidity
Storage
5% to 95% (non-condensing)
External 90-264 VAC, 47-63 Hz universal power
supply. Regional line cords are available.
Electrical
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Agency Approvals
n
UL 544 Medical Equipment Standard Part 42.5
n
CSA 22.2 No. 950-95 Canadian Safety Standard
n
IEC 950/EN 60950 International Safety Standard
n
FCC Class B
n
UL 1950 Domestic Safety Standard, 3rd Ed.
n
Canadian DOC Class A
n
EN50082-1:1997 International Immunity Standard
n
EN55022 Class B European Electromagnetic Radiation Standard
n
EN61000-3-2, 3 Powerline Disturbance
n
AS/NZS 3548 Australia EMC
n
CE Compliant
n
EMC Taiwan
n
CB Scheme Documents
Options
n
Peel-off
n
Cutter
n
Linerless
n
4 MB FLASH memory
n
8 MB FLASH memory
n
Real time clock with 4 MB FLASH
n
Real time clock with 8 MB FLASH
n
Power rewinder, 110 VAC
n
Power rewinder, 230 VAC
For details, call your authorized reseller.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial (RS-232) Connector Technical
Information
Pin No.
Description
Not used
1
RXD (receive data) input to the printer
2
3
TXD (transmit data) output from the printer
DTR (data terminal ready) output from the printer -- controls when
the host may send data
4
Chassis ground
5
6
DSR (data set ready) input to the printer
RTS (request to send) output from the printer -- always in the
ACTIVE condition when the printer is turned on
7
Not used
8
9
+5 V @ 0.75 A fused
NOTES: The maximum current available through the serial
and/or parallel port is not to exceed a total of 0.75 Amps.
When XON/XOFF handshaking is selected, data flow is controlled
by the ASCII control codes DC1 (XON) and DC3 (XOFF). The
DTR control lead will have no effect.
Interconnecting to DTE Devices
The printer is configured as data terminal equipment (DTE). To connect the
printer to other DTE devices (such as the serial port of a personal
computer), use an RS-232 null modem (crossover) cable.
Figure 31 shows the required cable connections.
Interconnecting to DCE Devices
When the printer is connected via its RS-232 interface to data
communication equipment (DCE) such as a modem, a STANDARD
RS-232 (straight-through) interface cable must be used. Figure 32 shows
the connections required for this cable.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Printer to a DTE Device
DB-25S
Connector
to DTE Device (PC)
DB-9P
Connector
to Printer
TXD
2
DCD
1
2
3
4
5
6
7
8
9
RXD
3
RXD
TXD
DTR
GND
DSR
RTS
CTS
RTS
4
CTS
5
DSR
6
GND
7
DCD
8
DTR
20
22
DB-9S
Connector
to DTE Device (PC)
DB-9P
Connector
to Printer
DCD
DCD
1
1
2
3
4
5
6
7
8
9
RXD
2
RXD
TXD
DTR
GND
DSR
RTS
CTS
TXD
3
DTR
4
GND
5
DSR
6
RTS
7
CTS
8
9
Figure 31
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Printer to a DCE Device
DB-25S
Connector
to DCE Device
DB-9P
Connector
to Printer
RXD
DCD
2
1
2
3
4
5
6
7
8
9
RXD
TXD
DTR
GND
DSR
RTS
CTS
TXD
3
CTS
4
RTS
5
DTR
6
GND
7
DCD
8
DSR
20
22
DB-9S
Connector
to DCE Device
DB-9P
Connector
to Printer
DCD
DCD
1
1
2
3
4
5
6
7
8
9
TXD
2
RXD
TXD
DTR
GND
DSR
RXD
3
DSR
4
GND
5
DTR
6
CTS
7
RTS
CTS
RTS
8
9
Figure 32
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Parallel Interface Technical Information
Pin No.
Description
nStrobe/Host Clk
1
Data Bits 1-8
2-9
10
nACK/PtrClk
Busy/Per Busy
PError/ACK Data Req.
Select/Xflag
11
12
13
nAuto Fd/Host Busy
Not Used
14
15
Ground
16 & 17
18
+5 V @ 0.75 A Fused
Ground
19-30
31
nInit
nFault/nData Avail.
Not Used
32
33 & 34
35
+5V through 1.8 KΩ Resistor
nSelectin/1284 active
36
NOTE: The maximum current available through the serial and/or
parallel port is not to exceed a total of 0.75 Amps.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
D
Adjustments
Damage, shipping . . . . . . . . 2
Darkness, adjusting . . . . . . . 23
Print darkness . . . . . . . . 23
Print speed . . . . . . . . . 23
Print width . . . . . . . . . 23
Agency approvals . . . . . . . . 44
Auto calibration. . . . . . . . . 18
Autobaud . . . . . . . . . . . . 22
DCE devices,
interconnecting . . . . . . . . 45
Defaulting the printer . . . . . . 30
DTE devices,
interconnecting . . . . . . . . 45
F
C
Factory defaults,
resetting . . . . . . . . . . 30, 31
Calibration
Auto . . . . . . . . . . . . . 18
Manual . . . . . . . . . . . 28
Cleaning
Fanfold media. . . . . . . . . . 17
Feed button . . . . . . . . . . . 19
Feed button modes . . . . . . . 31
Cutter . . . . . . . . . . . . 33
Exterior . . . . . . . . . . . 33
Interior . . . . . . . . . . . 33
Peel bar . . . . . . . . . . . 33
Platen roller . . . . . . . . . 33
Printhead . . . . . . . . . . 33
Tear bar . . . . . . . . . . . 33
I
Inspection . . . . . . . . . . . . 2
L
Loading the media
Communications parameters,
setting . . . . . . . . . . . . 22
Cutter mode . . . . . . . . . 14
Fanfold . . . . . . . . . . . 17
Peel-off mode. . . . . . . . . 9
Tear-off mode . . . . . . . . 5
Lubrication . . . . . . . . . . . 33
Communications diagnostics . . 30
Configuration label . . . . . . . 29
Cutter mode . . . . . . . . . . . 14
49
Download from Www.Somanuals.com. All Manuals Search And Download.
M
S
Maintenance parts. . . . . . . . 35
Manual calibration . . . . . . . 28
Media loading
Serial connector pinouts . . . . 45
Set communications (^SC) . . . 22
Specifications
Cutter mode . . . . . . . . . 14
Fanfold . . . . . . . . . . . 17
Peel-off mode. . . . . . . . . 9
Tear-off mode . . . . . . . . 5
Font/bar code . . . . . . . . 43
Label/tag . . . . . . . . . . 42
Physical/environmental/
electrical. . . . . . . . . . 43
Printing . . . . . . . . . . . 41
Status LED . . . . . . . . . 19, 25
O
Operator controls . . . . . . . . 19
Options . . . . . . . . . . . . . 44
T
Tear-off mode . . . . . . . . . . 5
Troubleshooting. . . . . . . . . 25
Troubleshooting tests . . . . . . 29
P
Parallel connector pinouts . . . 48
Parts list . . . . . . . . . . . . . 35
Peel-off mode . . . . . . . . . . 9
Pinouts
U
Unpacking . . . . . . . . . . . . 2
Parallel . . . . . . . . . . . 48
Serial . . . . . . . . . . . . 45
Power switch . . . . . . . . . . 19
Print darkness, adjusting . . 23, 31
Print speed, adjusting . . . . . . 23
Print width, adjusting . . . . 23, 31
Printhead, replacing. . . . . . . 36
Z
ZPL II . . . . . . . . . . . . . . 23
ZPL II Programming
Guide . . . . . . . . . . . . 1, 23
R
Recalibrating the printer . . . . 29
Repair parts . . . . . . . . . . . 35
Replacing the printhead. . . . . 36
Reporting damage, shipping . . . 2
Resetting the factory
defaults . . . . . . . . . . 30, 31
50
Download from Www.Somanuals.com. All Manuals Search And Download.
|