Zanussi Washer IZ10 User Manual

WASHING MACHINE

PRALKA AUTOMATYCZNA

AUTOMATICKÁ PRAČKA

AUTOMATICKÁ PRÁČKA

AUTOMATA MOSÓGÉP

IZ 10 - IZ 12

COTTONS

SYNTHETICS

90°C

60°C

50°C

40°C

30°C

1200

900

700

500

PREWASH

WASH

RINSES

SPIN

DELICATES

WOOL

PREW

ASH

SUPER

RINSE

HAND

RINSE

HOLD

QUICK

DRAIN

WASH

/PA

INSTRUCTION BOOKLET

INSTRUKCJA OBSLUGI

NÁVOD K OBSLUZE

NÁVOD NA OBSLUHU

HASZNÁLATI ÚTMUTATÓ

132999531

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Warnings

Disposal

4-5

Maintenance

Door seal

Bodywork

Detergent dispenser drawer

Drain filter

Tips for environmental protection 5

Water inlet filter

Emergency emptying out

Frost precautions

Technical specifications

Installation

Unpacking

Something not working?

23-24

Positioning

Water inlet

Water drainage

Electrical connection

Your new washing machine

Description of the appliance

Door locked pilot light

Detergent dispenser drawer

Use

Control panel

10-13

Controls

Washing hints

Sorting the laundry

Temperatures

Before loading the laundry

Maximum loads

Laundry weights

Removing stains

Detergents and additives

International wash code symbols

Operating sequence

Washing programmes

17-19

Download from Www.Somanuals.com. All Manuals Search And Download.

Warnings

The following warnings are provided in the interests of overall safety. You must read them carefully before

installing or using the appliance.

• Use only the recommended quantities of fabric

softener. An excessive amount could damage the

Installation

• All internal packing must be removed before using

laundry.

the appliance. Serious damage may be caused to

• Leave the porthole door slightly ajar when the

the machine or adjacent furniture if the protective

appliance is not in use. This preserves the door

transit devices are not removed or are not

seal and prevents the formation of musty smells.

completely removed. Refer to the relevant

• Always check that water has emptied out before

opening the door. If not, drain the water following

the instructions in the instruction book.

paragraph in the instruction book.

• Any electrical work required to install this appliance

must be carried out by a qualified electrician.

• Always unplug the appliance and shut the water

tap after use.

• Any plumbing work required to install this

appliance must be carried out by a qualified

plumber.

• After having installed the machine, check that it is

not standing on its electrical supply cable.

General safety

• Repairs to the machine must be carried out only by

qualified personnel. Repairs carried out by

inexperienced persons could cause serious

danger. Contact your local Service Centre.

• If the appliance is placed on a carpeted floor,

ensure that air can circulate freely between the feet

and the floor.

• Never pull the power supply cable to remove the

plug from the socket; always take hold of the plug

itself.

Use

• This appliance is designed for domestic use. It

must not be used for purposes other than those for

which it was designed.

• During high temperature wash programmes the

door glass may get hot. Do not touch it!

• Only wash fabrics which are designed to be

machine washed. Follow the instructions on each

garment label.

• Do not overload the appliance. Follow the

instructions in the instruction book.

• Make sure that all pockets are empty. Objects such

as coins, safety pins, pins and screws can cause

extensive damage.

• Do not machine wash garments saturated with

petroleum, methylated spirits, trichlorethylene, etc.

If such fluids have been used to remove stains

prior to washing, wait until they have completely

evaporated from the fabric before placing garments

in the appliance.

• Place small items such as socks, belts, etc. in a

cloth bag or pillowcase to prevent them getting

trapped between the drum and the tub.

Download from Www.Somanuals.com. All Manuals Search And Download.

To disable this device and restore the possibility of

closing the door, rotate the button anti-clockwise until

the groove is vertical.

Child safety

• Children are often not aware of how dangerous

electrical appliances can be. When the machine is

working, children should be carefully supervised

and not be allowed to play with the appliance.

• The packaging components (e.g. plastic film,

polystyrene) can be dangerous to children - danger

of suffocation! Keep them out of children’s reach.

• Keep all detergents in a safe place out of children’s

reach.

P1076

• Make sure that children or pets do not climb into

the drum. To avoid this the machine incorporates a

special feature. To activate this device, rotate the

button (without pressing it) inside the door

clockwise until the groove is horizontal. If

necessary use a coin.

• When the appliance is to be scrapped, cut off the

electrical supply cable and destroy the plug with

the remaining cable. Disable the door catch in

order to prevent children from becoming trapped

inside while playing.

Disposal

Packaging materials

Machine

The materials marked with the symbol

recyclable.

are

Use authorised disposal sites for your old appliance.

Help to keep your country tidy!

>PE<=polyethylene

>PS<=polystyrene

>PP<=polypropylene

This means that they can be recycled by disposing of

them properly in appropriate collection containers.

Tips for environmental protection

To save water, energy and to help protect the

environment, we recommend that you follow these

tips:

• With adequate pre-treatment, stains and limited

soiling can be removed; the laundry can then be

washed at a lower temperature.

• Normally soiled laundry may be washed without

prewashing in order to save detergent, water and

time (the environment is protected too!).

• Measure out detergent according to the water

hardness, the degree of soiling and the quantity of

laundry being washed.

• The machine works more economically if it is fully

loaded.

Download from Www.Somanuals.com. All Manuals Search And Download.

Technical specifications

DIMENSIONS

Height

Width

Depth

85 cm

60 cm

MAXIMUM LOAD

Cotton

5.5 kg

2.5 kg

Synthetics

Delicates

Woollens

SPIN SPEED

1200 rpm max.

POWER SUPPLY VOLTAGE/FREQUENCY

TOTAL POWER ABSORBED

220-230 V/50 Hz

2200 W

MINIMUM FUSE PROTECTION

10 A

WATER PRESSURE

Minimum

Maximum

500 kPa

800 kPa

This appliance complies with the following EEC Directives:

73/23/EEC of 19/02/73 relating to low voltage

89/336/EEC of 03/05/89 relating to electromagnetic compatibility.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Unpacking

Positioning

Install the machine on a flat hard floor.

Make sure that air circulation around the machine is

not impeded by carpets, rugs etc. Check that the

machine does not touch the wall or other kitchen

units.

Carefully level by screwing the adjustable feet in or

out. Never place cardboard, wood or similar

materials under the machine to compensate for any

unevenness in the floor.

All transit bolts and packing must be removed

before using the appliance.

You are advised to keep all transit devices so that

they can be refitted if the machine ever has to be

transported again.

1. Using a spanner, unscrew and remove the rear

right-hand bolt and lay the machine on its back,

taking care not to squash the hoses. This can be

avoided by placing one of the corner packing

pieces between the machine and the floor.

P1051

Water inlet

P0255

Connect the water inlet hose to a tap with a 3/4"

thread.

2. Remove the polystyrene block from the underside

of the machine and release the two plastic bags.

The other end of the inlet hose which connects to the

machine can be turned in any direction. Simply

loosen the fitting, rotate the hose and retighten the

fitting, making sure there are no water leaks

3. Carefully remove the right-hand bag (1) then the

left-hand bag (2) by pulling them towards the

centre of the machine.

P1068

P1066

P1088

P0021

4. Set the machine upright and remove the two

remaining bolts from the back.

The inlet hose must not be lengthened. If it is too

short and you do not wish to move the tap, you will

have to purchase a new, longer hose specially

designed for this type of use.

5. Pull out the three plastic spacers from the holes

into which the bolts were fitted.

6. Plug the open holes with the plugs which you will

find in the envelope containing the instruction

booklet.

P0256

P0020

Download from Www.Somanuals.com. All Manuals Search And Download.

Water drainage

Electrical connection

The end of the drain hose can be positioned in three

ways:

This machine is designed to operate on a 220-230 V,

single-phase, 50 Hz supply.

Hooked over the edge of a sink using the plastic

hose guide supplied with the machine. In this

case, make sure the end cannot come unhooked

when the machine is emptying.

This could be done by tying it to the tap with a piece

of string or attaching it to the wall.

Check that your domestic electrical installation can

take the maximum load required (2.2 kW), also

taking into account any other appliances in use.

Connect the machine to an earthed socket.

The manufacturer declines any responsibility

for damage or injury through failure to comply

with the above safety precaution.

Should the appliance power supply cable

need to be replaced, this should be carried

out by our Service Centre.

The power supply cable must be easily

accessible after installing the machine.

P0022

In a sink drain pipe branch. This branch must be

above the trap so that the bend is at least 60 cm

above the ground.

Directly into a drain pipe at a height of not less

than 60 cm and not more than 90 cm.

The end of the drain hose must always be

ventilated, i.e. the inside diameter of the drain pipe

must be larger than the outside diameter of the drain

hose.

The drain hose must not be kinked. Run it along the

floor; only the part near the drainage point must be

raised.

P0023

Download from Www.Somanuals.com. All Manuals Search And Download.

Your new washing machine

This new washing machine, which is fitted with the Jet system, patented Zanussi, meets all modern needs for

effective treatment of laundry with low water, energy and detergent consumption.

Further savings are achieved by washing small loads of laundry, since water and electricity consumption is

proportional to the quantity and type of laundry being washed.

• The possibility of selecting the temperature, spin speed and all the options offered by this washing machine

gives you truly “customised” washing.

• The DELAY START option allows you to delay starting of the wash programme to any time of day, so

allowing you for instance to make use of overnight economy electricity tariffs.

• The programme progress display shows the programme steps selected and the programme phase which

is running.

• The special wool programme with its new delicate wash system treats your woollens with extreme care.

• The balance control device ensures the machine is stable during the spin.

Description of the appliance

1 Detergent dispenser drawer

2 Control panel

3 Door locked pilot light

4 Drain filter

IZ 12

DELAY

COTTONS

SYNTHETICS

90°C

60°C

50°C

40°C

30°C

1200

900

700

500

ASH

PREW

WASH

NSES

PREWASH

DELICATES

WOOL

OFF

SPIN

SUPER

RINSE

HAND

RINSE

HOLD

QUICK

DRA

WASH

RESE

PAU

5 Adjustable feet

Door locked pilot light

It stays on during the whole programme indicating

that the door is locked.

When the light goes out, the door can be opened

(see page 19).

Detergent dispenser drawer

Prewash

Main wash

Fabric softener, starch

C0063

Download from Www.Somanuals.com. All Manuals Search And Download.

Use

Control panel

4 TEMPERATURE button

1 ON/OFF button

Press this button repeatedly to increase or decrease

the temperature, if you want your laundry to be

washed at a temperature different from the one

proposed by the washing machine. The relevant light

will light up.

Press this button to switch the washing machine on.

Press the ON/OFF button again to switch the

machine off.

2 MAINS-ON light

This light is connected to the ON/OFF button. It

lights up when you press the button, and goes out

when you press it again.

Maximum temperatures are 95°C for cotton, 60°C for

synthetic fabrics, 40°C for delicate fabrics, wool and

fabrics to be hand-washed (HAND WASH

programme).

Important!

By depressing TEMPERATURE and SPIN SPEED

buttons simultaneously, the acoustic signal at the

end of the cycle is suppressed.

3 FABRIC button

Press this button repeatedly to select the

programme on the basis of the type of laundry to be

washed. The light relevant to the selected

programme will light up. The washing machine will

propose a temperature and automatically select the

maximum spin value provided for the programme

you have chosen. You can change these values by

operating buttons 4 and 5.

5 SPIN SPEED button

Press this button repeatedly to change the spin

speed, if you want your laundry to be spun at a

speed different from the one proposed by the

washing machine. The relevant light will light up.

Maximum speeds are:

Hand wash

• for cotton: 1,200 rpm (IZ 12), 1,000 rpm (IZ 10);

• for synthetic fabrics, wool, and fabrics to be hand-

washed: 900 rpm (IZ 12), 850 rpm (IZ 10);

• for delicate fabrics: 700 rpm (IZ 12), 650 rpm (IZ

10).

When you select this programme, you obtain a

particularly delicate washing, suitable for articles of

clothing whose label indicates that they must be

hand-washed

RINSE HOLD position : when you choose this

option, the machine will not drain the water of the

last rinse, so as not to wrinkle the laundry.

At the end of the cycle, the light of the

START/PAUSE button will flash, to indicate that the

water must be drained.

To complete the cycle, choose one of the following

options:

Download from Www.Somanuals.com. All Manuals Search And Download.

• Draining and spin:

8 Display

The following pieces of information are shown on the

display:

- Press the START/PAUSE button. The machine

will drain the water, then spin the laundry at the

maximum speed provided for the selected

programme.

• Three blinking dashes, when a programme is

cancelled by means of the SKIP/RESET button.

- Select spin speed by means of button 5, and

press the START/PAUSE button.

• Drain only

- Press the SKIP/RESET button once, so as to

cause the DRAIN light to light up, then press the

START/PAUSE button.

The three blinking dashes will also appear when you

press the ON/OFF button to switch the machine on,

if the previously selected cycle has been erased.

Important! If you accidentally press the

SKIP/RESET button more than once, the display

will show three blinking dashes. To drain the

water, select any washing programme by means

of the FABRIC button, then press SKIP/RESET

three times in order to select the DRAIN position

(only the DRAIN light will remain lit).

---

•

Duration of washing programme in hours

and minutes, after you have selected a

programme.

6 OPTIONS button

Press this button to select the following options:

• PREWASH: select this option if you wish your

laundry to be prewashed before the main wash

(not available for wool and hand-wash cycle).

The prewash ends with a short spin at 650 rpm in

programmes for cotton and synthetic fabrics,

whereas in the programme for delicate fabrics the

water is only drained.

2.05

• SUPER RINSE: this option can be selected with all

programmes except the wool programme and

hand wash. The machine performs 4 rinses

instead of 3. This option is recommended for

people who are allergic to detergents, and in areas

where the water is very soft.

While the programme is running (after you have

pressed the START/PAUSE button), the displayed

time value decreases by one unit every minute.

• The washing machine has stopped with water in

the tub, at the end of a programme with the

RINSE HOLD option: this is indicated by a static

zero.

7 TIME SAVE button

• The washing machine has completed the

programme: this is indicated by a blinking zero.

At the same time, the door locked light goes out.

The zero will reappear when you switch the

washing machine on, unless the previous

programme has been erased by means of the

SKIP/RESET button.

This button allows you to select the QUICK WASH

function, for laundry that is only slightly soiled (not

for wool and HAND WASH programme).

The washing time will be reduced according to the

type of fabric and the selected temperature.

Download from Www.Somanuals.com. All Manuals Search And Download.

E20

9 START/PAUSE button

This button has three functions:

Important!

The first time you use the washing machine,

when you switch it on, it may display a blinking zero and

give an audible warning signal. This is due to the fact

that the washing machine has performed a washing

cycle during the manufacturer’s inspection tests, and

this cycle has not been erased after its completion.

• Start: after you have selected the desired

programme and options, press this button to start

the washing machine. The light above the button

will stop flashing and remain lit.

If you have selected a delay time by means of

button 11, the countdown will begin and will be

shown on the display.

• Delay start, a time value indicated in hours and

selected by means of the relevant button.

• Pause: when you press this button again, the

programme in progress is interrupted. The light

above the button will start flashing. To restart the

programme, press the button again.

When you PAUSE the cycle, the DOOR LOCKED

light goes out, and it becomes possible to open the

door, provided

• the washing machine is not in the heating phase;

• the level of the water is not high;

• the drum is not turning.

The delay time is displayed for 5 seconds, then the

duration of the selected programme reappears.

After you have pressed the START/PAUSE button,

the countdown begins, and the delay time value

decreases by one unit every hour.

Important! You must set the washing machine to

PAUSE before you make any change in the

programme in progress.

• Draining of water and spinning after the

execution of programmes with the RINSE HOLD

option.

You can delay the start of the selected programme

by up to 24 hours in one hour intervals.

• An incorrect option selection has been made:

this is indicated by the message Err when a

function incompatible with the current programme

is selected.

10 SKIP/RESET button

At the end of a programme, you must press this

button once or repeatedly, in order to clear the

contents of the memory (the display will show three

blinking dashes); otherwise, the next time you switch

the washing machine on, the blinking zero will

reappear and the audible warning signals relevant to

the end of the previous cycle will be given.

You can also press the RESET button to exclude

one or several phases of the programme which is

running, as indicated below.

- set the washing machine to PAUSE by pressing the

START/PAUSE button (the relevant light will flash);

The incorrect selection is also indicated by an

audible warning signal.

- press the RESET button once or several times, until

the required phase(s) is(are) cancelled (the light next

to the name of the phase(s) will go out).

• An alarm code indicates a fault in the machine

operation (see the relevant chapter on page 23).

Download from Www.Somanuals.com. All Manuals Search And Download.

Example:

11 DELAY button

In this case, both the

drain and the spin (at

the speed provided for

the selected type of

fabric) will be

This button makes it possible to delay the starting of

the programme by up to 24 hours. The delay you

have selected is shown on the display for about 5

seconds; afterwards, the duration of the programme

reappears.

You must select this option after you have set the

programme and before you press the

START/PAUSE button.

performed.

The time value shown on the display will decrease

by one unit every hour.

This button allows you also to select special

You can change the delay time at any moment,

before you press the START/PAUSE button.

programmes, such as RINSES, SPIN and DRAIN.

• If the machine is already switched on because it

has just performed a washing programme, proceed

as follows:

If you have already pressed the START/PAUSE

button, and you wish to change or cancel the delay

time, proceed as follows:

- depress RESET once or repeatidly to cancel the

previously performed programme (three blinking

dashes will appear on the display);

• set the washing machine to PAUSE by pressing the

START/PAUSE button;

- select the type of fabric by means of the relevant

button;

• press the DELAY button until the display shows the

desired delay time or

- select the special programme:

• press the DELAY button once, to erase the delay

time. The display will indicate “0h”.

• RINSES

• press the START/PAUSE button again.

Depress RESET once, the pilot light WASH

goes out.

Important!

• SPIN

The door will be locked throughout the delay time

(DOOR LOCKED light lit).

Depress RESET twice, the pilot lights WASH

If you need to open the door, you must first set the

washing machine to PAUSE by pressing the

START/PAUSE button. After you have closed the

door, press the START/PAUSE button again.

and RINSES go out.

• DRAIN

Depress RESET three times, the pilot lights

WASH, RINSES and SPIN go out.

Example:

12 Programme phase indicator

lights

In this case the

machine will perform

the rinses and spin.

When you select a programme, the lights relevant to

the phases that form the programme light up.

• If the machine is switched off:

- depress ON/OFF button to switch it on;

- select the type of fabric by means of button

FABRIC:

- select the special programme as previously

described.

After you have started the programme, only the light

relevant to the phase that is currently being carried

out will remain lit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Laundry weights

The following weights are indicative:

Washing hints

bathrobe

1200 g

100 g

700 g

500 g

200 g

250 g

200 g

100 g

200 g

100 g

600 g

200 g

500 g

100 g

Sorting the laundry

Follow the wash code symbols on each garment

label and the manufacturer’s washing instructions.

Sort the laundry as follows:

napkin

quilt cover

sheet

whites, coloureds, synthetics, delicates, woollens.

pillow case

tablecloth

Temperatures

towelling towel

tea cloth

95°

for normally soiled white cottons and linen

(e.g. tea cloths, towels, tablecloths,

sheets...)

night dress

ladies’ briefs

man’s work shirt

man’s shirt

60°

for normally soiled, colour fast garments

(e.g. shirts, night dresses, pyjamas....) in

linen, cotton or synthetic fibres and for

lightly soiled white cotton (e.g. underwear).

man’s pyjamas

blouse

(cold)for delicate items (e.g. net curtains), mixed

30°-40° laundry including synthetic fibres and

men’s underpants

woollens.

Removing stains

Before loading the laundry

Stubborn stains may not be removed by just water

and detergent. It is therefore advisable to treat them

prior to washing.

Never wash whites and coloureds together. Whites

may lose their “whiteness” in the wash.

New coloured items may run in the first wash; they

should therefore be washed separately the first time.

Blood: treat fresh stains with cold water. For dried

stains, soak overnight in water with a special

detergent then rub in the soap and water.

Make sure that no metal objects are left in the

laundry (e.g. hair clips, safety pins, pins).

Oil based paint: moisten with benzine stain

remover, lay the garment on a soft cloth and dab the

stain; treat several times.

Button up pillowcases, close zip fasteners, hooks

and poppers. Tie any belts or long tapes.

Remove persistent stains before washing. Rub

particularly soiled areas with a special detergent or

detergent paste.

Dried grease stains: moisten with turpentine, lay

the garment on a soft surface and dab the stain with

the fingertips and a cotton cloth.

Treat curtains with special care. Remove hooks or tie

them up in a bag or net.

Rust: oxalic acid dissolved in hot water or a rust

removing product used cold. Be careful with rust

stains which are not recent since the cellulose

structure will already have been damaged and the

fabric tends to hole.

Maximum loads

Recommended loads are indicated in the

programme charts.

Mould stains: treat with bleach, rinse well (whites

and fast coloureds only).

General rules:

Grass: soap lightly and treat with bleach (whites and

fast coloureds only).

Cotton, linen: drum full but not too tightly packed;

Synthetics: drum no more than half full;

Ball point pen and glue: moisten with acetone (*),

lay the garment on a soft cloth and dab the stain.

Delicate fabrics and woollens: drum no more than

one third full.

Lipstick: moisten with acetone as above, then treat

stains with methylated spirits. Remove any residual

marks from white fabrics with bleach.

Washing a maximum load makes the most efficient

use of water and energy.

For heavily soiled laundry, reduce the load size.

Red wine: soak in water and detergent, rinse and

treat with acetic or citric acid, then rinse. Treat any

residual marks with bleach.

Download from Www.Somanuals.com. All Manuals Search And Download.

Ink: depending on the type of ink, moisten the fabric

first with acetone (*), then with acetic acid; treat any

residual marks on white fabrics with bleach and then

rinse thoroughly.

Quantity of detergent to be used

The type and quantity of detergent will depend on

the type of fabric, load size, degree of soiling and

hardness of the water used.

Tar stains: first treat with stain remover, methylated

spirits or benzine, then rub with detergent paste.

Water hardness is classified in so-called “degrees” of

hardness. Information on hardness of the water in

your area can be obtained from the relevant water

supply company, or from your local authority.

(*) do not use acetone on artificial silk.

Follow the product manufacturers’ instructions on

quantities to use.

Detergents and additives

Good washing results also depend on the choice of

detergent and use of the correct quantities to avoid

waste and protect the environment. Although

biodegradable, detergents contain substances

which, in large quantities, can upset the delicate

balance of nature.

Use less detergent if:

– you are washing a small load,

– the laundry is lightly soiled,

– large amounts of foam form during washing.

The choice of detergent will depend on the type of

fabric (delicates, woollens, cottons, etc.), the colour,

washing temperature and degree of soiling.

Degrees of water hardness

All commonly available washing machine detergents

may be used in this appliance:

Degrees

Level

Characteristic

– powder detergents for all types of fabric,

German

°dH

French

°T.H.

– powder detergents for delicate fabrics (60°C max)

and woollens,

0- 7

8-14

0-15

16-25

26-37

– liquid detergents, preferably for low temperature

wash programmes (60°C max) for all types of

fabric, or special for woollens only.

soft

medium

hard

15-21

The detergent and any additives must be placed in

the appropriate compartments of the dispenser

drawer before starting the wash programme.

more than more than

21 37

very hard

If using concentrated powder or liquid detergents, a

programme without prewash must be selected.

The washing machine incorporates a recirculation

system which allows an optimal use of the

concentrated detergent.

Pour liquid detergent into the dispenser drawer

compartment marked

programme.

just before starting the

Any fabric softener or starching additives must be

poured into the compartment marked

starting the wash programme.

before

Follow the product manufacturer’s recommendations

on quantities to use and do not exceed the «MAX»

mark in the detergent dispenser drawer.

Download from Www.Somanuals.com. All Manuals Search And Download.

International wash code symbols

These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.

Energetic wash

Max. wash

temperature

95°C

Max. wash

temperature

60°C

Max. wash

temperature

40°C

Max. wash

temperature

30°C

Hand wash

Do not

wash

at all

Delicate wash

Bleaching

Ironing

Bleach in cold water

Do not bleach

Hot iron

max 200°C

Warm iron

max 150°C

Lukewarm iron

max 110°C

Do not iron

Dry cleaning

in all solvents

Dry cleaning

Dry cleaning in

perchlorethylene,

petrol, pure alcohol,

R 111 & R 113

Dry cleaning

in petrol,

Do not

dry clean

pure alcohol

and R 113

high

temperature

low

temperature

Drying

Flat

On the line

On clothes

hanger

Tumble dry

Do not

tumb

le dr

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Switch the machine on

Press the ON/OFF button to switch the machine on.

The display will show three blinking dashes or a

blinking zero. The light above the button will light up.

Operating sequence

Before washing your first load of laundry, we

recommend that you run a cotton cycle at 60°C, with

the machine empty, in order to remove any

manufacturing residue from the drum and tub.

Pour half a measure of detergent into the main wash

compartment and start up the machine.

---

1. Place the laundry in the drum

Open the door.

Place the laundry in the drum, one item at a time,

shaking them out as much as possible.

Close the door.

5. Select the desired programme/

fabric

Press the FABRIC button repeatedly, in order to

select the desired programme/fabric. The relevant

light will light up.

The lights relevant to the phases that form the

programme will light up.

The display will show the duration of the selected

programme, calculated on the basis of the maximum

load for each type of fabric. The START/PAUSE

button light will start flashing.

P1084

2. Measure out the detergent

Pull out the dispenser drawer until it stops. Measure

out the amount of detergent recommended by the

manufacturer in a graduated cup and pour it into the

If the load of laundry to be washed is small, at the

beginning of the cycle the display will still indicate the

duration relevant to the maximum load. The duration

value will be gradually adjusted during the execution

of the cycle.

main wash compartment

If you wish to carry out the prewash, pour detergent

into the appropriate compartment marked

3. Measure out the additive

If required, pour fabric softener into the compartment

marked

, without exceeding the «MAX» mark.

C0064

C0065

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Select the temperature

9. Select the QUICK WASH option

Press the TEMPERATURE button if you wish to

select a temperature value different from the one

proposed by the washing machine.

Depress TIME SAVE button to select the QUICK

WASH option, if your laundry is only slightly soiled.

The relevant light illuminates.

The relevant light will light up.

10. Select the DELAY TIME

7. Select the spin speed or the

RINSE HOLD option

Press the SPIN SPEED button repeatedly, in order

to select the desired spin speed or the RINSE HOLD

option. The relevant light will light up.

If you select the RINSE HOLD option, the machine

will stop at the end of the programme with the water

still in the tub.

Before you start the programme, if you wish the

starting to be delayed, press the DELAY button

repeatedly, or keep it pressed, to select the desired

delay. The selected delay time value (up to 24 hours)

will appear on the display for 5 seconds, then the

duration of the programme will appear again.

DELAY

11. Start the programme

Press the START/PAUSE button. The relevant light

will stop flashing, the DOOR LOCKED light will light

up, and only the light relevant to the phase that is in

progress will remain lit.

If you have chosen a delayed start, the washing

machine will begin the countdown.

8. Select the desired options

If your laundry is very dirty, it may be advisable to

select the PREWASH option.

If you wish the laundry to undergo an extra rinse,

select the SUPER RINSE option.

Press the OPTIONS button so as to cause one or

both of the lights to light up.

The display will show the duration of the programme

or the selected delay.

Download from Www.Somanuals.com. All Manuals Search And Download.

Pay attention to the level and temperature of the

water in the washing machine!

12. How to change a programme

during its cycle

Before you make any change, you must pause the

washing machine by pressing the START/PAUSE

button.

When you close the door and press the ON/OFF

button again, the washing machine will resume the

programme from the point where it had been

interrupted.

It is possible to change any phase before the

programme carries it out.

Changing the type of fabric or temperature is

possible, obviously, only during the washing phase.

When you make a change in these two parameters,

the washing machine will resume the cycle from the

beginning.

15. End of programme

At the end of the programme, the washing machine

stops automatically, gives an audible signal, and

displays a blinking zero.

If you had selected the RINSE HOLD option, the

START/PAUSE button light flashes to indicate that

the water must be drained. The display shows a

steadily lit zero.

When the programme has been completed, a

blinking zero appears on the display and the audible

signal is given.

If it is necessary to drain the water in order to change

the programme in progress, proceed as follows:

• PAUSE the machine by pressing the

START/PAUSE button;

• press the SKIP/RESET button repeatedly, until

only the DRAIN light remains lit;

The DOOR LOCKED light goes out at once.

• press the START/PAUSE button again.

Press the SKIP/RESET button repeatedly to erase

the programme that has just been carried out. If

you omit to do this, the next time you switch the

washing machine on, the blinking zero will

appear on the display and you will hear the

audible signal.

When the water has been drained, the display shows

a blinking zero. You may now select a new

programme and press the START/PAUSE button to

start it.

13. How to cancel a programme

during its cycle

To cancel a programme that is being carried out, first

pause the washing machine by pressing the

START/PAUSE button, then press the SKIP/RESET

button repeatedly, until the display shows three

blinking dashes.

Note: when you switch the machine on, if you must

erase the previously performed programme, it is also

sufficient to press the FABRIC button and select a

new programme.

Press the ON/OFF button to switch the machine off.

The relevant light will go out.

Remove the laundry from the washing machine.

Check whether the drum is completely empty, by

rotating it with your hand. The purpose of this is to

prevent any items of laundry from remaining

accidentally in the drum, where they might get

damaged in a subsequent wash (e.g. by shrinking) or

bleed colour into another load of laundry.

14. How to open the door during

the cycle of a programme

You can open the door, after having set the washing

machine to PAUSE, provided the following

conditions exist:

We advise you to close the water supply tap and

disconnect the plug from the socket.

• the washing machine is not in the heating phase

beyond 40°C;

Leave the door ajar in order to air the washing

machine.

• the level of the water is not high;

• the drum is not turning.

If these requirements are met, when you pause the

washing machine, the DOOR LOCKED light goes

out and the door can be opened.

Should it not be possible to open the door, and

should it be absolutely necessary to do so, switch

the machine off by pressing the ON/OFF button.

After approximately 2 minutes, you can open the

door.

Download from Www.Somanuals.com. All Manuals Search And Download.

Washing programmes

Type of

Consumption*

laundry and

symbols on

labels

Max

load

Programme/ Description of

Available options

temperature

programme

Energy

kWh

Water

litres

Time

h/min.

5.5 kg

Cottons

60°-95°C

Main wash at

60°-95°C

3 rinses

SPIN SPEED

RINSE HOLD

PREWASH

SUPER RINSE

QUICK

1.8

2.29

White cotton:

e.g. sheets,

tablecloths,

household

linen

Long spin

5.5 kg

Cottons

60°-40°-30°C 60°-40°-30°C

3 rinses

Main wash at

SPIN SPEED

RINSE HOLD

PREWASH

SUPER RINSE

QUICK

0.95

2.10

Coloured

cotton: e.g.

shirts,

Long spin

blouses,

underwear,

towels, house-

hold linen

2.5 kg

Synthetics

60°-40°-30°C 60°-40°-30° or

Main wash at

SPIN SPEED

RINSE HOLD

PREWASH

SUPER RINSE

QUICK

0.9

0.7

1.27

1.04

Synthetic

fabrics and

blends: e.g.

shirts,

blouses,

underwear

cold wash

3 rinses

Short spin

2.5 kg

Delicates

40°-30°C

Main wash at

40°-30°C or

cold wash

3 rinses

SPIN SPEED

RINSE HOLD

PREWASH

SUPER RINSE

QUICK

Delicate fab-

rics: e.g.

acrylic fabrics,

viscose, poly-

ester,

Short spin

synthetic

blends

2 kg

Wool

40°-30°C

Main wash at

40°-30°C or

cold wash

3 rinses

SPIN SPEED

RINSE HOLD

0.3

Wool

Short spin

Hand wash Main wash at

40°-30°C

SPIN SPEED

RINSE HOLD

0.25

40°-30°C or

cold wash

3 rinses

Short spin

The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on

the quantity and type of laundry, on the inlet water temperature and on the ambient temperature. It refers to

the highest temperature for each wash programme. For cotton items it refers to a wash load of 5 kg.

** In compliance with EC directive 92/75 the consumption figures indicated on the Energy label refer to this

programme at 60°C with a load of 5 kg of cotton items.

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance

Detergent can also accumulate inside the drawer

recess: clean it with an old toothbrush. Refit the

drawer after cleaning.

1. Door seal

Check from time to time the door seal and eliminate

eventual possible objects that could be trapped in

the fold.

P0038

P1050

4. Drain filter

The drain filter collects threads and small objects

inadvertently left in the laundry. Check regularly that

the filter is clean.

2. Bodywork

Clean the outside of the machine with warm water

and a neutral, non-abrasive household detergent.

Rinse with clean water and dry with a soft cloth.

Open the filter door by pulling it towards the right.

Place a container under the filter to catch any

spillage.

Important: do not use methylated spirits, solvents or