Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Page
4
Contents
Installing the oven
General information
The cooling fan for the controls
Ignition
5
5
6
Oven lights
6
Lighting the oven and grill
The grill
7
9
The grill pan and handle
The oven
12
14
16
17
18
21
24
27
28
32
34
35
37
Baking trays and dishes
Blank page
Oven cooking charts
Slow cooking
The electronic timer
Hints and tips for automatic cooking
Care and cleaning
What is wrong and why?
Replacing an oven light bulb
Service and spare parts
Guarantee
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Installing the oven
For your safety
This oven must be installed and serviced by a competent person
as stated in the Gas Safety (Installation & Use) (Amendment)
regulations current edition.
It is important that the oven is suitable for your gas supply.
Your installer should check the data badge.
Cabinet Dimensions
This oven must be fitted into a cabinet with a suitable sized aperture.
Minimum aperture height
Minimum aperture width
Minimum aperture depth
874mm
560mm
560mm
For more details on suitable cabinet sizes refer to the Installation and
Servicing Instructions supplied with your oven.
Location
For your safety
All gas ovens require adequate ventilation. The room the oven is
fitted in must have a good air supply that meets the standard BS
5440 Part 2 (current edition). Your installer will tell you if you are
not sure.
The oven may be placed in a kitchen, kitchen/diner or bedsit
but not in a bathroom or shower room. It should not be installed
in a bedsit smaller than 20m3. (Ask your installer).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
General information
To get the best results from your new oven please read these
instructions carefully.
You should pay particular attention to cooking times and gas mark
settings as these may differ from your previous oven. You may find it
necessary to adjust these until you are more familiar with the oven.
For your safety
Do not block any of the oven vents.
Never line any part of the oven with aluminium foil.
Do not let items which can catch fire or electric mains leads such
as kettle flexes trail over any part of the oven.
Oven housing units vary widely in construction and finish. To avoid
possible damage to the housing unit, you must not leave cabinet doors
or flaps above the oven open or partially open when you use the grill or
oven. If you have a storage area above your oven it will become warm
when you use the oven. Do not store perishable foods in the storage
area above the oven.
The cooling fan for the controls
Your oven has a cooling fan. The cooling fan will start to work as soon
as you light the grill or oven. You will be able to hear the fan when it is
working.
The cooling fan may continue to work after you have turned off the
oven or grill. It will switch itself on and off until the oven has cooled
down.
If you want to turn off the electrical supply to the oven, you should
not do so until the cooling fan has stopped working.
For your safety
When you are using the grill or oven warm air will exhaust from
the grill cavity and the vents below the control panel.
Take care not to stand too close to the oven or grill while in use.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Ignition
The grill and oven burners light automatically when you turn on the
control. If, for any reason either of the burners go out, the spark ignition
will automatically relight it.
Please note:
You can only use the grill with the door fully or partially open. You
cannot use the grill when the door is closed.
You cannot use the oven or grill in the event of a power failure.
Oven lights
Your oven is fitted with two oven lights.
The oven lights will come on when you use the oven.
Oven light bulbs will usually last for many months. If one or both lights
do not work, you probably need to replace a bulb. See page 34 for
details on how to change an oven light bulb.
Connecting to the electricity supply
For your safety
This cooker must be earthed and protected by a 3 amp fuse.
The plug supplied with the oven can be fitted directly to a suitable three
pin earthed socket.
If you have to change the fuse replace it with a 3 amp fuse which
has been ASTA approved to BS 1362.
Do not use the plug until you have put the fuse cover back on. If the
fuse cover is lost you can get a replacement from an electrical retailer.
The correct replacement can be identified by marking or colour coding.
If you cut the plug off dispose of it safely as it will be a shock hazard
if it is inserted into a 13 amp socket elsewhere in the house.
If the ignition system doesn't work there may be a fault with the
electrical supply. First, check the socket by trying out another piece of
electrical equipment in it, if that works correctly renew the fuse in the
plug.
If the fuse keeps failing there is a fault in the oven which must be put
right. Do not use a fuse with a rating higher than 3 amps. Do not carry
out other electrical work. Unplug the oven and tell your installer.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Lighting the oven and grill
Grill
To light:
1 Open the grill door. Push in the control knob and turn it to the
highest setting. This is shown by a large flame symbol.
Oven
To light:
1 Open the oven door.
2 Push in the control knob and turn it to gas mark 9. When the burner
has lit there will only be small flames at first.
3 Now turn the control knob to the gas
mark you want.
4 Wait until the burner is showing large
flames.
5 Close the oven door.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
To turn off any burner
1 Push in the control knob and turn it to the off position.
This is shown by a large dot.
For your safety
When you are lighting any burner check that it has lit before
you leave the oven.
When you are turning off a burner do not leave the oven until
the flame has gone out.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
The grill
When you first turn the grill on you will be able to smell residues from
the grill surface being burnt off. It may be necessary to open a window
for ventilation.
The smell will disappear after using the grill a few times.
Heat control
The grill gives variable heat settings.
The control knob turns to the left from
'OFF' to 'HIGH' and then to 'LOW'. The high
setting should be used for fast cooking such
as toast. Use a lower setting to cook thicker
foods such as chicken after it has been
browned on the high setting.
You should remember to turn the food
regularly.
You should not use the grill to keep food warm as it will continue to
cook the food.
The grill pan should be used on the shelf without the metal plate
underneath it. The shelf can be positioned in any of the runner
positions. You can reverse the grill pan grid to suit different types of
food.
If you close the door whilst the grill burner is lit, it will go out and you
will hear a continuous 'sparking'. The burner will automatically re-light
when you open the door.
For your safety
You must keep the grill door fully or partially open when the grill
burner is lit.
Accessible parts may be hot when the grill is used.
Young children should be kept away.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Cooking positions
Most food should be cooked on the grid in
the grill pan. You can turn the grid over to
suit different thicknesses of food.
You can place some dishes straight on
the grill shelf. This is useful when you are
browning the top of food such as cauliflower
cheese.
Preheating
You don't usually need to preheat the grill. You may wish to preheat it
for a couple of minutes when you are cooking steak or browning food.
Putting food on the grid
Place food such as toast, tea-cakes and
muffins towards the centre of the grid. If you
put food outside this area it may require
rotating during cooking.
Place food which needs a more gentle
heat, such as tomatoes or mushrooms
towards the edge of the grid.
Arrange meat, meat products and fish to
suit their thickness and how you like them
cooked.
To prevent excess fat splashing when you use the grill place the trivet in
the grill pan below the grill grid.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Grill shelf
The grill shelf can be slotted into place in any of two positions. For
safety the shelf will only pull out so far. If you want to remove the shelf
completely pull it forward as far as it will go, raise the front edge and lift
it out. To put the shelf into a different position, keep the front edge
raised, slot the shelf onto the runner, lower the front edge and slide the
shelf in.
You should use the shelf without the
metal plate when grilling.
Use shelf position one when toasting and
adjust the height of the grid to suit.
Shelf positions are counted from the top
downwards.
For your safety
Always remove the grill pan before attempting to adjust the shelf
position. Oven gloves should be used when removing the grill
pan or pulling the shelf in and out.
Always remove the grill pan handle during grilling.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
The grill pan and handle
The grill pan has a removable handle. This should be removed during
grilling.
To attach the handle, press the button on the handle with your thumb.
Lift the handle upwards slightly and put it into the widest part of the grill
pan bracket. Move the handle to the left and lower into position. You
can now release the button. Make sure the handle is firmly located.
When you remove the handle, press the button on the handle with your
thumb and lift the handle upwards slightly and towards the right to
remove it from the grill pan bracket.
For your safety
Make sure your hand is protected when removing the grill pan
handle as the grill can become very hot.
Always make sure you remove the grill pan handle when grilling.
If left in position it will get hot.
To sit the grill pan on the shelf correctly, make sure that the cut out on
the underside of the handle bracket sits over the front bar of the shelf.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
To check the progress of the food when using the grill you should
withdraw the grill pan on the shelf to attend to food. After removing the
grill pan you can rest it on a heat resistant work surface if you need to.
Plate warming
You can use the grill compartment to warm plates while the oven is on.
Do not place plates to warm under the grill when it is on as this may
damage the plates.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
The oven
Before you use the oven you should wipe it
out with a damp cloth to remove any dust.
When you first turn the oven on you will be
able to smell residues from the oven
surfaces being burnt off. It may be necessary
to open a window for ventilation.
The smell will disappear after using the oven a few times.
Heat zones
There are zones of heat within the oven. The temperature in the middle
is the gas mark you have chosen.
The top of the oven is slightly hotter and the lower shelf slightly
cooler. The base of the oven is quite a lot cooler. You can make use of
these heat zones when you are cooking foods requiring different
temperatures all at the same time. You can use the base of the oven to
warm plates.
If you are cooking more than one tray of similar items, for example
cakes or biscuits, swap the trays around during cooking. Or you could
remove the top tray when the food is cooked and move the lower tray to
the higher shelf to finish cooking.
Preheating
You do not need to preheat the oven for casseroling and so on.
Preheat the oven for baking or when you are cooking sensitive food
such as Yorkshire puddings, soufflés and yeast mixtures.
When you are cooking or reheating frozen or chilled food read the
instructions on the packaging.
When you need to preheat the oven, we recommend you do so for
20 minutes.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Oven shelves
The two oven shelves can be slotted into place in any of 5 positions. For
safety the shelves will only pull out so far. If you want to remove a shelf
completely, pull it forward as far as it will go, raise the front edge and lift
it out.
To put the shelf into a different position, keep the front edge raised,
slot the shelf onto the runner, lower the front edge and slide the shelf in.
The shelf positions are counted from the
top downwards and recommended shelf
positions are given in the cooking charts on
pages 18, 19 and 20. When cooking always
try to leave at least one runner position
between shelves to allow the heat to
circulate properly.
The recommended shelf positions given in the oven cooking charts give
the best results.
When you only need to use one shelf you can store the other shelf
above or below the one you are using where there is more space.
Use the shelf with the metal plate in a higher runner position when
cooking on two levels.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Baking trays and dishes
For your safety
Never place cooking dishes, trays
and so on over the oven burner.
This will damage the oven as well
as the ovenware and possibly the
cabinet underneath the oven.
Leave a gap of 13mm (½") between all
dishes and the sides of the oven so the
heat can circulate properly.
Do not push dishes too far back as food
will burn if it overhangs the burner flames.
The baking tray we have supplied with your oven has been designed
and tested to give the best results from your oven. If you use a tray or
tin which is larger than this, you may need to turn it around during
cooking.
Place single dishes on the centre of the shelf. You may need to turn
large items around during cooking.
Condensation
Condensation may form on the oven. This is quite normal and nothing
to worry about. The condensation forms when heat and moisture are
present, for example during cooking. Whenever possible try to make
sure that food which contains a lot of moisture for example casseroles
are covered. If you do notice any condensation, wipe it up straight away.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
This page has been intentionally left blank.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Oven cooking chart
These instructions are for cooking in the oven after it has been pre-heated for 20 minutes.
When you are using both shelves, use the shelf with the metal plate in the higher position.
If you are cooking more than one tray of similar items, for example cakes or biscuits, swap the trays around during cooking or you
can take the top tray out of the oven when the food is cooked and move the lower tray to the higher shelf to finish cooking.
Always leave at least one shelf position between shelves to allow heat to circulate.
The recommended shelf positions give the best results.
Put the dishes in the centre of the shelf.
You can change the gas marks and cooking times to suit your own tastes.
It is important to check that food is piping hot before serving.
Gas
mark
5
Shelf
Approximate
Food
Roasting meat:
position cooking time
4*
Beef
Rare:
20 mins. per ½kg (1 lb) and 30 mins.
25 mins. per ½kg (1 lb) and 25 mins.
30 mins. per ½kg (1 lb) and 30 mins.
25 mins. per ½kg (1 lb) and 25 mins.
30 mins. per ½kg (1 lb) and 30 mins.
30 mins. per ½kg (1 lb) and 30 mins.
35 mins. per ½kg (1 lb) and 35 mins.
Medium:
Well Done:
Medium:
Well Done:
Medium:
Well Done:
Lamb
5
5
4*
4*
Pork and Veal
Thoroughly thaw frozen joints before cooking them.
* Recommended position for shelf with metal plate.
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas
mark
5
Shelf
Approximate
Food
Poultry:
position cooking time
4*
5
5
4*
Chicken
20 mins. per ½ kg (1 lb) and 20 mins.
Turkey below 4.5kg (10lbs) 4
over 4.5kg (10 lbs) 4
25 mins. per ½ kg (1 lb) and 25 mins.
15 mins. per ½ kg (1 lb) and 15 mins.
25 mins. per ½ kg (1 lb)
Duck and duckling
5
Stuffed poultry
Cook as above but calculate weight including stuffing
Thoroughly thaw frozen joints before cooking them.
The times given above are for when you are open roasting. If you cover the food with foil or a lid you should allow an extra 5
minutes cooking time for each ½ kg (1 lb).
Yorkshire pudding - large
- individual
7
7
2*
2*
25-30 mins.
15-25 mins.
Cakes:
Very rich fruit cake
Rich fruit cake 180mm (7")
205mm (8")
According to recipe
2
2
4
5
7
5*
5*
5*
1* & 4
1* & 4
2¼ hours.
2½-2¾ hours.
60 mins.
15-25 mins.
10-20 mins.
Madeira,
Small cakes
Scones
180mm (7")
Victoria sandwich
180mm (7")
4
4
2* & 4
2* & 4
20-30 mins.
20-35 mins.
205mm (8")
* Recommended position for shelf with metal plate.
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas
Shelf
Approximate
Food
Mark
Position cooking time
Pastries:
Plate tart (shortcrust)
Fruit pie (shortcrust)
Mince pies (flan pastry)
Profiteroles (choux pastry)
6
6
5
4
2*
2*
1* & 4
2
25-35 mins.
25-35 mins.
20-25 mins.
25-30 mins.
To help pastry brown on the underside cook on a metal plate, or if plates are flat and have no rim underneath, place on baking
tray to cook.
Puddings:
Milk puddings
Baked sponge pudding
Baked custard
2
4
3
3
4*
2
1½-2 hrs.
45-60 mins.
50-60 mins.
Yeast mixtures:
Bread 0.45kg (1 lb loaves)
0.90kg (2 lb loaves)
Rolls and buns
8
8
8
3*
3*
2*
30-40 mins.
30-40 mins.
15-20 mins.
Note: You must soak dried beans then boil them in an open pan for 15 minutes before you add them to any dish.
*Recommended position for shelf with metal plate.
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Slow cooking
The slow cook setting gives a very low heat in the oven. It is particularly
useful when you are cooking soups, stews and casseroles because the
long slow cooking will make cheaper, tougher cuts of meat more tender.
Some foods such as pastry and biscuits are not suitable for slow
cooking because the temperature is too low.
Cover all food during cooking to prevent it from drying out. You can
uncover food for the last half hour if it is normally served golden brown.
Food preparation-slow cooking
Joints of meat and poultry
l Do not cook meat joints over 2.7kg (6lb).
l Do not cook poultry over 2kg (4lb 8oz).
l Cook on the middle shelf of the oven or above.
l Cook stuffing separately.
l Cook for at least 6 hours.
l Only cook joints of pork if you can make sure, by using a meat
thermometer, that the temperature inside the joint is at least 88oC.
l For good air circulation always stand joints on a rack in the roasting
tin or casserole
l Thaw all frozen meat and poultry before you cook it.
l Prime cuts of meat do not benefit from slow cooking.
l Cut off unwanted fat and skin unless it is browned first.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Soups, casseroles and stews
l Do not cook casseroles over 3kg (6lb).
l Do not cook two (1.8kg) (2lb) casseroles on slow cook setting at the
same time.
l Cook in the middle of the oven or above.
l Cover food with a tight fitting lid or tin foil.
l Cook for up to 9 hours.
Vegetables
l Cut into small pieces.
l Dried beans must be pre-soaked then boiled in an open pan for 15
minutes before adding to any dish.
l To prevent vegetables from discolouring, add lemon juice.
l Place vegetables under meat in casseroles.
l Cover food with a tight fitting lid or tin foil.
l Cook for up to 6 hours.
Milk puddings
l Make the pudding in the usual way.
l For delicate puddings such as egg custard, place the dish in a bain
marie and cover the dish with tin foil.
l Cook for 2 - 4 hours.
General points for slow cooking
Frozen foods
Thaw thoroughly before cooking.
Thickening
Toss meat in flour for casseroles. Alternatively blend cornflour with
water and add it at the end of cooking.
Flavouring
Flavours are held in the food because there is little evaporation. Adjust
flavouring at the end of the cooking time.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Liquid
Use slightly less liquid as there is little evaporation during cooking.
Milk and milk products, for example cream
Add these towards the end of cooking to prevent them from curdling.
Reheating
Cool left over food quickly and then put it in the fridge.
Do not reheat food using the slow cook setting. Reheat food in the usual
way or in a microwave.
Only reheat food once.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
The electronic timer
Please note that this is a 24 hour clock, for example 2pm is shown as
1400.
Cookpot symbol
In the following pages we explain how to
set the controls. Read through them until
you're familiar with the procedure. We have
supplied a plastic card as a quick reference
when setting the timer.
Selector
Setting knob
If the oven is switched off on the wall, or there is a loss of power, the
clock will stop and you will not be able to use the oven. When you first
switch the electricity supply on, the timer display will flash.
During the hours of 10p.m. (22.00hrs) and 6a.m. the display will glow
dim. If a function is selected the display will glow brighter until the
function is complete. It will then revert back to the dim mode.
To set the time of day
Turn and hold the selector knob to clock.
The cookpot symbol (
) is showing.
Set the correct time by turning the setting
knob clockwise. Adjust the time by turning
the setting knob in either direction. The
selector knob will return to 'manual' when
you let go of it.
To use the minute minder
Turn the selector knob to 'timer'
Turn the setting knob clockwise until the
display shows the time you want. Our
diagram shows the timer set to 5 minutes.
When you are using the minute minder you can make the clock show
the time of day by turning the selector knob to 'manual'.
At the end of the timed period an alarm will sound. Switch off the alarm
by turning the selector knob to 'manual'.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Automatic control
When you use the automatic controls for the first time it's probably best
to choose a time when you are at home. That way you can check to
make sure you've set everything correctly and you'll feel much more
confident when you are away from home in the future.
Setting the controls for automatic use
This is very easy. All you have to do is work through the steps below.
The clock will work out the rest for itself.
1 Is the electricity supply on?
2
Is the clock
showing the
correct time?
To adjust turn and hold
the selector knob to
'clock' and turn the
setting knob in either
direction.
3
How long will
the food take
to cook?
Turn the selector knob to
'cook'. Then turn the
setting knob until the
length of time you want
the food to cook shows
in the display. The
maximum cooking time
is 23 hours and 59
minutes. 'Auto' will show
in the display.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
4 What time do Turn the selector knob to
you want the 'Stop'. Turn the setting knob
food to be
cooked by?
until the time the oven is to
switch off shows in the
display. The cookpot (
will go out.
)
The 'Stop' time must not be
more than 23 hours 59
minutes from the time of
day. For example if the time
of day is 9.00 am the latest
'Stop' time will be 8.59 am
the next day.
5 Set to
Turn the selector knob to
'automatic'. The time of day
will show in the display.
automatic.
6 Turn on the
oven control.
Turn the oven control to
mark 9 then to the gas mark
you want.
The time shown on the chart gives an example of setting the automatic
controls when the time is 9.00 am, the food is to be cooked for 2½
hours and the food is needed at 6.00 pm (1800 hours).
The clock will work out what time the oven will switch itself on and it will
turn the oven off at the end. Once the automatic sequence is finished
there will be an alarm and the 'Auto' symbol flashes to remind you that
you need to set the oven for manual operation. To do this turn the
selector knob to 'manual'.
Turn off the oven control.
To cancel an automatic programme
If you change your mind and want to cancel a programme that you have
set turn the selector knob to 'Cook' and turn the setting knob until 0.00
shows in the display.
Turn the selector knob to 'manual'.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Hints and tips for automatic cooking
1 Check the instructions for setting the automatic controls until you are
familiar with the timer operation.
2 If the oven has been used, allow it to cool completely before using
for automatic cooking.
3 You should leave food in the oven for as short a time as possible
before automatic cooking starts.
4 Do not leave food to stand in the oven when it has finished cooking.
You should remove it and if it is not going to be eaten at once, cool it
quickly.
5 If you cannot remove food from the oven as soon as it is cooked
make sure that the food is covered.
6 Choose perishable foods carefully, especially during warm weather.
7 Food should be fresh and preferably straight from the refrigerator.
8 Joints of meat and poultry must be completely thawed.
9 Dishes containing left over cooked meat or poultry should not be
cooked automatically if there is a delay period.
10 Choose dishes which require approximately the same cooking time.
Slight variations may be allowed by:-
i) placing foods in larger or smaller containers
ii) using more or less liquid
iii) cutting fruit or vegetables into larger or smaller pieces.
These will give longer or shorter cooking times respectively. Further
temperature adjustments can be made by placing the foods higher
or lower in the oven as the top of the oven is hotter than the bottom.
11 Arrange shelf positions to suit dishes and choose dishes which will
fit into the oven together.
12 As food may be standing for some time in the oven, cover dishes
with foil or a lid where possible, and in the case of roast potatoes
and joints of meat, brush with a little fat or oil. Lemon juice may be
added to fruit and vegetables to prevent browning.
13 Cream should be added just before serving.
14 If alcohol is used fermentation can occur.
15 Green leaf vegetables which take only a short time to cook, should
not be placed into the oven with the automatic meal. It is far better to
cook them in a pan on the hotplate whilst dishing up the rest of the
meal.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Care and cleaning
For your safety
For hygiene and safety reasons you must keep this gas oven
clean. A build up of fat or other foodstuff could cause a fire.
Try to mop up spills and splashes as soon as they happen.
But be careful as parts of the appliance will be hot.
Do not use any polishes, caustic cleaners, abrasives, washing soda or
soap powder except those recommended in this booklet.
Please note: If we recommend you
use hot soapy water we mean hot
water with washing up liquid in it and
not any other cleaning product.
If you own a dishwasher please
read the operating instructions for the
machine before you wash any part of
your cooker.
Clean your oven regularly using a cloth that has been wrung out in
hot soapy water. Rinse and polish it dry using a soft cloth.
When you remove parts of your oven for cleaning do not plunge
them into water whilst they are very hot as this may damage the finish of
the parts.
You must not remove the control knobs when cleaning the control
panel.
The grill
Clean the grill compartment, the shelf, grill pan and handle, grid and
trivet, and the inner grill door while they are still slightly warm. This way
you can easily remove any splashes and spills. Clean them with a cloth
that has been wrung out in soapy water. You may use mild abrasives
such as 'Jif'. For more stubborn marks you may occasionally need to
use a soap filled pad such as 'Brillo'.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
The oven
Clean the base of the oven, the oven shelves, the meat tin, cake tray,
and the oven door while they are still slightly warm. This way you can
easily remove any splashes and spills. You may use mild abrasives.
The heat in the oven will change the colour of the metal plate on the
shelf. You must not remove the solid plate from the shelf. You can soak
the shelf for a few minutes in hot soapy water to make cleaning easier.
If you use any oven cleaners on the oven base they must have the
Vitreous Enamel Development Council (VEDC) seal of approval. Follow
the instructions on the cleaning agent and protect the oven burner with
aluminium foil to prevent it from becoming blocked. Do not use any
cleaning products on the top, sides and back of your oven.
The top, sides and back of your oven are coated in a special material
which helps to keep itself clean.
Follow these simple rules to maintain the appearance of the special
finish.
Do not overfill dishes or they will boil over.
Do not use dishes too high in the oven. If
you do they may stick to the oven roof.
Cover your roasting tins with foil. This will
prevent fat splashing.
Use a roasting tin which is just large
enough for the meat and potatoes. This will
help to reduce fat splashing.
Dry any vegetables that you are going to
roast. If they are wet there will be more fat
splashing.
Follow the oven cleaning cycle regularly.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Oven cleaning cycle
You need to follow the cycle to keep the inside of the oven in good
condition. The type of cooking you do will affect how often you need to
follow the cycle.
If you do a lot of roasting and very little baking you should follow the
cleaning cycle once a week. If you do very little roasting you will only
need to follow the cleaning cycle every 2-3 weeks.
To carry out a cleaning cycle:
1 Remove the oven shelves.
2 Set the oven to mark 5 for
at least 30 minutes.
3 Turn the temperature up to
mark 7 for 2 hours or until
the oven is presentably
clean. Some staining will
remain.
Do not use any cleaning agents
or scrapers on the inside of the
oven. Do not wash the special
finish.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Cleaning between the outer and inner
door glass
You can remove the glass from the oven and grill doors if you need to.
The grill door is fitted with a trim. You must note the correct position of
the trim when you remove the grill door glass.
To remove the outer glass
1 Open the door so you can get at the two cross head screws on the
top of the door.
2 Loosen these two screws using a pozidrive screwdriver.
3 You should hold the door glass securely in place with one hand,
whilst removing the screws completely, with the other hand. If you
do not do this, the door glass could fall forward. Still holding the door
glass, remove the trim from the top of the grill door.
Note the correct position of the grill door trim. The oven door does
not have a trim.
4 Using both hands, gently tilt the top of the door glass towards you.
Lift it slightly to disengage the locators at the bottom of the door.
5 Clean the outer and inner glass using hot soapy water and mild
abrasives such as 'Jif'.
6 Replace the glass by holding it in both hands and gently placing the
locators into the holes of the brackets at the bottom of the door.
Push the top of the glass towards the door, and make sure the
screw location holes line up. Replace the trim on top of the grill door
making sure that it is correctly positioned. You can check this by
looking through the air gap on the top of the door and checking that
the screw location holes line up.
7 Hold the glass in place with one hand and replace the cross head
screws into the location holes, with the other hand.
8 Tighten the screws using a pozidrive screwdriver. Close the door.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
What is wrong and why?
We strongly recommend that you carry out the following checks on your
oven before calling a Service Engineer. It may be that the problem is a
simple one which you can solve yourself, without the expense of a
service call.
If the Service Engineer finds that the problem is listed below, you will be
charged for the call whether or not the cooker is under guarantee.
Problem
The oven or grill will not light.
Check
l Check that the oven is switched on at the wall.
l Check that the timer is set to 'manual' (See page 26).
l Check that there has not been a power failure. If the electricity
supply has been interrupted or you have switched the oven off at the
wall the grill may have cut out before the cooling fan has cooled the
oven down. Switch the oven on at the wall until the cooling fan has
cooled it down.
l Check that there is not a problem with your gas supply. You can do
this by making sure that other gas appliances such as your central
heating or gas fire are working.
Problem
Food is cooking too quickly or too slowly.
Check
l Check that you are using the recommended gas marks and shelf
positions. See pages 18, 19 and 20. Be prepared to adjust the gas
mark up or down to achieve the results you want.
Problem
The oven is not cooking evenly.
Check
l Check that the oven is installed properly and is level.
l Check you are using the recommended temperatures and shelf
positions.
l If you are using a tin or tray which is larger than the one we
supplied, be prepared to turn it round during cooking
l If you are cooking a large item be prepared to turn it round during
cooking.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Problem
Having difficulty cleaning any part of the oven.
Check
l Check that you are following the instructions for care and cleaning
(See page 28).
Problem
The oven lights do not work.
Check
l Check that the oven is not set for automatic cooking. The lights will
illuminate when cooking begins.
l If you have had your oven for some time you may need to replace
an oven light bulb. (See page 34).
Problem
The timer does not work.
Check
l Check that the timer instructions are being closely followed.
(See page 24).
Problem
The oven or grill burner flame is unstable/noisy.
Check
l Check that the burner flames stabilise after a few minutes. It may be
that the appliance needs to adjust to room temperature.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Replacing an oven light bulb
You need a 25 Watt small Edison screw with a temperature rating of
T300.
l Make sure the oven is cool before you replace a bulb.
l Unplug the oven.
l Open the oven door and remove the oven shelves.
l Pull the glass bulb cover towards you and then pull it off.
l Unscrew the bulb by turning it to the left.
l Fit a new bulb and then replace the glass bulb cover.
l Replace the oven shelves.
l Plug the oven back into the electricity supply.
l Re-set the time of day.
The oven light bulbs are not covered by the manufacturers guarantee.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Service and spare parts
For your safety
Maintenance work must only be done by a competent person. Do
not try to repair the oven yourself. This could be dangerous. It is
dangerous to alter or modify the product in any way.
Help us to help you
Please determine your type of enquiry before writing or telephoning.
Service
It is a recommendation by the manufacturer that annual servicing of the
product is done by the manufacturers approved service organisation.
Before calling out an Engineer, please ensure that you have read the
details under the heading 'What is wrong and why?' and have the model
number and purchase date to hand. The telephone number for service
is:
08705 929929
PLEASE NOTE that all enquiries concerning service should be
addressed to your local Zanussi Customer Service Centre.
Some Regional Electricity Companies are responsible for the servicing
of cookers sold through their own retail outlets. For service contact your
local Electricity Showroom.
When you report a problem try to describe the nature of the fault.
Always give your ovens full name, model and serial numbers which you
can see when the oven door is opened.
Make a note of this information in this space:
Name:
Model Number:
Serial Number:
G.C. Number:
Please note that all enquiries concerning service should be addressed
to your local Customer service centre.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Customer care department
For general enquiries concerning your Zanussi cooker or further
information on Cooking, Cooling or Washing products, you are invited to
contact our Consumer Care Department by letter or telephone as
follows:
Customer Care Department
Zanussi Limited
Zanussi House
Hambridge Road
Newbury
Berkshire
RG14 5EP
Tel: (01635) 521313
The Gas Consumers' Council
The Gas Consumers' Council (GCC) is an independent organisation
which protects the interests of gas users. If you need advice, you will
find the telephone number in your local telephone directory under Gas.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Z D G 5 8
Peace of mind for twenty-four months
Zanussi standard guarantee conditions
This guarantee is in addition to your
Exclusions
statutory and other legal rights which will
not be excluded or in any way diminished
by the return of the guarantee card
This guarantee does not cover:
supplied with the cooker.
l Damage or calls resulting from
transportation, improper use or
neglect, the replacement of any light
bulbs or removable parts of glass or
plastic.
We, Zanussi Limited, undertake that if
within 24 months of the date of the
purchase this ZANUSSI appliance or any
part thereof is proved to be defective by
reason only of faulty workmanship or
materials, we will, at our option repair or
replace the same FREE OF ANY CHARGE
for labour, materials or carriage on
condition that:
l Cost incurred for calls to put right
machines improperly installed or
calls to machines outside the UK and
the Republic of Ireland.
l The appliance has been correctly
installed and used only on the
electricity supply stated on the rating
plate.
l Appliances found to be in use within
a commercial or similar environment,
plus those which are subject to rental
agreements.
l The appliance has been used for
normal domestic purposes only
and in accordance with the
l Products of Zanussi manufacture
which are NOT marketed by Zanussi
Limited.
manufacturers
operating
and
maintenance instructions.
l The appliance has not been
serviced, maintained, repaired,
taken apart or tampered with by any
person not authorised by us. Any
servicing or repairs carried out by
any unapproved third party will
invalidate the approvals status of
this product.
l For EEC Countries. The standard
guarantee is applicable but subject to
the owners responsibility and cost to
ensure the appliance meets the
standards set by the country to which
the product is taken. The Zanussi
company in the country concerned
will be pleased to advise further.
Sight of your purchase receipt will be
required by them.
All service work under this guarantee must
be undertaken by a Zanussi Service Force
Centre.
Home visits are made between 8.30am
and 5.30pm Monday to Friday. Visits may
be available outside these hours in which
case a premium will be charged.
Any appliance or defective part replaced
shall become our property.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
OVEN
Burner
Natural Gas
L.P.Gas
Sheet metal construction mounted transversely at rear of oven
Heat Input
Injector Marking
Flame Supervision
Device
Thermostat
Thermostat By-Pass Marking 74
2.4kW (8189 Btu/h)
108
2.4kW (172 g/h)
078
Diamond 'H' G.S.D. 100/28
Diamond 'H' 1100/110/B2
Diamond 'H' G.S.D.100/30
Diamond 'H' 1100/114/B2
79
IMPORTANT - SAFETY REQUIREMENTS
This appliance must be installed in accordance with the Gas Safety (Installation and Use) Regulations
Current Editions. Detailed recommendations are contained in the following British Standard Codes of Practice
- BS.6172, BS5440: Part 2 and BS.6891. All British Standards must be 'Current Editions'.
PROVISION FOR VENTILATION
The room containing the appliance should have an air supply in accordance with BS.5440: Part 2 Current
Edition. All rooms require an openable window or equivalent and some rooms will require a permanent vent
as well. For room volumes up to 5m3 an air vent of 100cm2 is required for room volumes between 5m3 and
10m3 an air vent of 50cm2 is required. If the room has a door that opens directly to the outside, no air vent is
required. For room volumes that exceed 11m³ no air vent is required. If there are other fuel burning
appliances in the same room, BS.5440: Part 2 Current Edition should be consulted to determine the requisite
vent requirements.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION OF APPLIANCE
The appliance may be located in a kitchen, a kitchen/diner or bedsitting room, but not located in a bathroom or
shower room.
It is essential that there is a minimum clearance of 3mm between the top surface of the appliance and
the inside top of the cabinet. The unit must be fitted into a cabinet conforming to Fig. 1. The following
internal dimensions are particularly important.
Height
Width
Depth
Depth
874..............Minimum
560..............Minimum
560..............Minimum
575..............Minimum
879.............. .Maximum
570............... Maximum
N/A................Maximum
N/A................Maximum
Solid Pipe
Flexible Pipe
NOTE: Where a cupboard door with a handle is situated above the appliance, we recommend a minimum
clearance gap of 5mm between fascia top trim and door.
Fig.1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Flexible Pipe Installation.
1. FITTING THE APPLIANCE AND CABINET
3
It is recommended that a /8, 1100mm long angled bayonet flexible hose (BFS) and a ½" straight socket
(BFS) be used for the installation. However any approved hose of the right length can be used.
IMPORTANT: Flexible tubing used must comply with B.S. 669 current editions L.P.G. flexible connections
must be of a type suitable for L.P.G. and capable of operation up to 50mbar and carry a red stripe, band or
lable.
NOTE:Only liquid sealants can be used in threaded gas connections. Do not use P.T.F.E. tape.
1
2
Make suitable arrangements for gas and electric supplies into the installation site. Preferably a junction
box or 3 pin earth socket should be situated at the back of the cabinet below the oven.
The electrical connection to the appliance is at the rear bottom right hand side, the junction box or socket
should be positioned accordingly.
3
4
Fit the cabinet as Fig.1, making sure that it is level.
When unpacking the appliance keep it on it's polystyrene base until it is put into the cabinet to avoid
damage.
5
Remove the oven and grill doors
i)
Open door fully.
ii)
iii)
Engage both hinge locking pins (See Fig. 2).
To remove the door, clear the hinges by raising the door slightly whilst pulling towards you.
Fig.2
HINGE
LOCKING PIN
6
Remove the fascia panel .
i)
Remove the gas control knobs, springs, bezels and
timer control knobs.
ii)
iii)
Remove the four screw (two each side) which are
visible on the underside of the fascia. Fig.3.
Tilt the bottom of the fascia panel out over. Withdraw
the fascia panel by moving it down over to disengage it
from the top fixing lugs. Take care not to lose the two
rubber grommets from the timer.
NOTE The thermostat and grill discs will remain attached to the
fascia panel. When refitting the control knobs and bezels, the
drive pins on the rear of the bezel must first be located in the disc
carrier. The knob and spring can now be fitted onto the control
spindle. To prevent the top fascia panel mounts becoming slack, it
may be necessary to adjust the top fixing lugs.
Fig.3
5
Download from Www.Somanuals.com. All Manuals Search And Download.
7
8
If the gas supply bayonet and wall fixing bracket are to be located behind the appliance. It must be
located in the shaded area as indicated in Fig.5.
Connect flexible hose to the gas inlet supply block see Fig.5 (The flexible supply pipe must be suitable
for use at 70°C above ambient). The hose should be long enough to allow the appliance to be withdrawn
from the cabinet.
9
Position the appliance in front of the cabinet and run the supply cable (See Section 2) through the
cabinet and connect to the junction box or socket. Ensure that the supply is isolated at this stage.
Connect flexible hose to the bayonet connector.
10 Lift the appliance into the cabinet making sure the hose and supply cable are not trapped. Push the
appliance as far back as it will go.
11 Centralise and fix the appliance using the six wood screws provided, in the position indicated in Fig.4.
12 Carry out a gas soundness check.
NOTE: Check the gas supply pressure before fitting the fascia. (See Section 3).
Fig.4
FIXING
POINTS
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Solid Pipe Installation
FITTING THE APPLIANCE AND CABINET.
1
Make suitable arrangements for gas and electrical supplies into the installation site. Preferably a junction
box or 3 pin earthed socket should be situated at the back of the cabinet below the oven.
The electrical connection to the appliance is at the rear bottom right hand side, the junction box or socket
should be positioned accordingly.
2
3
4
5
Fit cabinet as Fig. 1, making sure that it is level.
When unpacking the oven keep it on it's polystyrene base until it is put into the cabinet to avoid damage.
Remove the oven and grill doors
i)
Open door fully.
ii)
iii)
Engage both hinge locking pins (See Fig. 2).
To remove the door, clear the hinges by raising the door slightly whilst pulling towards you.
6
Remove the fascia panel .
i)
Remove the gas control knobs, springs, bezels and timer control knobs.
ii)
iii)
Remove the four screw (two each side) which are visible on the underside of the fascia. Fig. 3.
Tilt the bottom of the fascia panel out over. Withdraw the fascia panel by moving it down over to
disengage it from the top fixing lugs. Take care not to lose the 2 rubber grommets from the timer.
GAS INLET SUPPLY BLOCK
Fig.5
120
NOTE The thermostat and ghen refitting the control knobs
120
and bezels, the drive pins on the rear of the bezel must first be located in the disc carrier. The knob and
spring can now be fitted onto the control spindle. To prevent the top fascia panel mounts becoming slack, it
may be necessary to adjust the top fixing lugs.
7
Solid gas pipe installation:
i) Remove the inlet elbow securing bracket and screws. See Fig.9. Slacken and remove the union nut
on the gas supply elbow on the right hand side of the control panel.
ii) Remove the two screws on the gas inlet block Fig.5.
iii) Withdraw the gas inlet block and pipe assembly from the back of the appliance.
iv) Remove the union elbow from the inlet block and pipe assembly. The elbow will be required in the final
installation.
v) The union elbow should be connected to the gas supply pipe via a standard ¼" B.S.P. straight
connector.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Install the gas supply pipe on site complete with the union elbow (See Fig.6). Note the orientation of the
elbow.
8
9
Position the appliance in front of the cabinet and run the supply cable (See Section 2) through the
cabinet and connect to the junction box or socket. Ensure that the supply is isolated at this stage.
Lift the appliance into the cabinet making sure the gas supply pipe enters the duct in the rear of the
appliance and the cable is not trapped by the appliance. Push the appliance as far back as it will go.
Ensure the supply pipe comes through the control panel and pull through any slack cable.
10 Centralise and fix the appliance to the cabinet using six wood screws in the position indicated in Fig.4
11 Tighten the union nut into the supply elbow.
12 Replace the inlet elbow securing bracket.
13 Carry out a gas soundness check.
NOTE:Check supply pressure before fitting fascia (See Section 3).
225
mm
FRONT VIEW
SIDE VIEW
Fig.6
2. CONNECTION TO ELECTRICITY SUPPLY
WARNING:This appliance must be earthed, do not earth this appliance to the gas supply piping.
This appliance must be connected to a 220V-240V AC. 50Hz supply which incorporates a 3 ampere fuse. If
any other type of plug is used it should incorporate a 5 ampere fuse either in the plug or adapter or at the
distribution borad. The appliance is supplied with 2 meters (6.5 ft) of 5 ampere 3 core cable fittted with a
moulded plug. If this proves to be insufficient to allow the appliance to be plugged into the nearest supply
socket, the supply cable can be either:
i)
Replaced totally by a longer cable at least 0.75mm² nominal cross sectional area (24/0.2).
ii) Extended by using a B.E.A.B. approved 3-way
sealed flex connector with integral flex clamps.
DO NOT EXTEND THE CABLE USING PLASTIC
OR CERAMIC CONNECTION TERMINAL BLOCKS
AND/OR INSULATION TAPE.
If the supply cable is replaced it is recommended that
the ends of the new cable all be cut to the same
length 60mm, any excess wire being stored inside the
mains terminal see Fig.7.
Should the supplied cable be required to be threaded
through small apertures in the cabinets it can be
removed from the mains inlet terminal block see Fig.7.
If the supplied plug is cut off dispose of it safely as it
will be a shock hazard if inserted into a 13 amp socket
elsewhere in the house.
Fig.7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
To fit a 3 pin 13 amp plug to the end of the appliance cable (Fig.8).
Connect the wires as follows:
BROWN to the live terminal.
BLUE to the neutral terminal.
GREEN and YELLOW to the earth terminal.
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is GREEN and YELLOW must be connected to the terminal in the plug which is marked
with the letter 'E' or by the earth symbol or coloured GREEN or GREEN and YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter 'N' or
coloured black.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter 'L'
or coloured RED.
FIT A 3 AMP FUSE TO THE PLUG FUSE HOLDER
GREEN AND
YELLOW
3 AMP
BLUE
BROWN
Fig.8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3. PRESSURE TESTING
The pressure test point is located on the right hand side of the gas rail. Access to the test point is
through a cut out in the top right hand side of the control panel see Fig.9.
1
2
3
Remove the hex head plug from the test point.
Connect the pressure gauge to the test point.
Check the supply pressure by turning the oven thermostat to Mark 9 then turn on the gas and electricity
supplies. Allow the oven burner to light and gas flow open up to full rate.
The pressure should be
For Natural Gas
For L.P.Gas
20mbar
28mbar for Butane,37mbar for Propane
4
Turn off the gas and electricities supply and the thermostat disconnect the pressure gauge and replace
the test point plug. Turn on the gas supply and check for gas soundness.
NOTE . The electrical supply must be connected in order to test the pressure
PRESSURE TEST
POINT
Fig.9
INLET ELBOW
SECURING BRACKET
INLET ELBOW
4. RE-ASSEMBLE THE APPLIANCE
1
2
Refit the fascia panel.
Re-fit the oven and grill doors.
5. CHECKING THE GRILL
1
2
Place the grill pan containing the trivet under the grill burner.
With the grill door open, turn on the grill tap, check that there is a spark from it's ignition system. This
should continue until the burner is alight.
3
There is a safety switch which shuts off the gas supply to the grill burner when the door is closed. Check
that it is operational by slowly closing the grill door, the gas supply should be shut off to the burner before
the grill door is fully closed.
NOTE: The burner will continue to spark.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
PART NO: 311280704
Download from Www.Somanuals.com. All Manuals Search And Download.
|