INSTRUCTION BOOKLET
DISHWASHER
ZT 415
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNINGS
It is most important that this instruction book should be retained with the appliance for future reference.
Should the appliance be sold or transferred to another owner, or should you move house and leave the
appliance, always ensure that the book is left with the appliance in order that the new owner can get to
know the functioning of the appliance and the relevant warnings.
These warnings are provided in the interest of safety. You MUST read them carefully before installing or
using the appliance.
■ Do not put in your dishwasher; cutlery with wooden
Installation
or horn handles or glued parts, bronze cutlery,
■ This appliance is heavy. Care should be taken
saucepans with wooden handles, unless they are
sold as dishwasher proof, aluminium ware, crystal
ware, leaded glass, plastic articles unless sold as
dishwasher proof, antique china or fine decorated
china unless sold as dishwasher proof. Always
check with the manufacturer of the item if in any
doubt.
when moving it.
■ It is dangerous to alter the specifications or attempt
to modify this product in any way.
■ Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
■ Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
■ A chemical reaction can occur between silver
cutlery and stainless steel cutlery. As a precaution,
do not wash together.
■ Any plumbing work required to install this
appliances should be carried out by a qualified
plumber or competent person.
■ Care should be taken when cleaning the bottom
door seal and hinge area as any exposed metal
edges may cut if care is not taken.
■ Built-in dishwashers only: The appliance must be
secured to the underside of the worktop using the
brackets provided. Failure to do this could result
in an unstable appliance which may cause damage
or injury.
■ This product should be serviced by an authorised
Zanussi engineer, and only genuine Zanussi spare
parts should be used.
■ Under no circumstances should you attempt to
repair the machine yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Contact your local Zanussi Service
Centre. Always insist on genuine Zanussi Spare
Parts.
Child Safety
■ This appliance is designed to be operated by
adults. Children should not be allowed to tamper
with the controls or play with the product.
Conservation
In the interests of the Environment:
During Use
When disposing of your old appliance:
■ Zanussi dishwashers are designed to be used for
washing normal household utensils. Items that are
contaminated by petrol, paint, steel or iron debris,
corrosive, acidic or alkaline chemicals are not to be
washed in a dishwasher.
■ Help to keep your country tidy - use authorised
disposal sites for your old appliances.
■ The materials used on this appliance marked with
the symbol
are recyclable.
■ Under no circumstances should you open the door
whilst,the appliance is in operation. Always turn off
the appliance before opening the door.
■ Check with your local Council or Environmental
Health Office to see if there are facilities in your
area for re-cycling this appliance.
■ When finishing loading or unloading close the door,
■ If you are discarding an old appliance that has a
lock or catch on the door, you must ensure that it is
made unusable to prevent young children being
trapped inside.
as an open door can be a hazard.
■ Unplug the appliance and turn off the water after
use.
■ If your house is fitted with a water softening unit or if
you live in a soft water area, it is not necessary to
add salt to the water softening unit in the dishwasher.
PAV04GB
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Remove all packaging before positioning the
machine.
To make this easier, the
hose itself may be turned to
the left or the right. In either
case, be sure to incorporate
the strainer (A) supplied
with the machine into the
joint. See picture.
Positioning
If possible, position the machine next to a water tap
and a drain.
The dishwasher features fill and drain hoses which
can be turned either to the left or the right to suit the
installation .
CA06
Caution: the retaining ring must be correctly fitted to
avoid water leaks.
Levelling
Avoid bends or kinks in the hose which could prevent
or slow down the flow of water.
Good levelling is essential for correct closure and
sealing of the door.
If the machine is connected to new pipes or pipes
which have not been used for a long time, you are
advised to run the water for a few minutes before
connecting the inlet hose. This will prevent deposits of
sand or rust clogging the inlet hose filter.
When the appliance is correctly levelled, the door will
not catch on the spacers on either side of the cabinet.
Water Outlet Connection
The end of the drain hose can be connected as
follows:
to the sink outlet siphon, securing it if necessary with
a clip;
IN12
IN11
If the door does not close correctly, loosen or tighten
the adjustable support feet, until the machine is
perfectly level.
to a wall outlet provided with vent-hole, minimum
internal diameter 4 cm;
The waste connection must be at a height of between
30 cm (minimum) and 100 cm (maximum) from the
floor.
Water Supply Connections
This dishwasher must be permanently plumbed into a
cold water supply.
The water pressure must be within the limits given in
the technical specifications, as it will not function cor-
rectly if pressure is outside these specifications.
Your local Water Authority will advise you on the average
mains pressure in your area.
+ 2 m max
Where the water is supplied via a cold water storage
cistern, you can work out the pressure yourself by mea-
suring the vertical distance (or «head») between the
machine's inlet hose and the outlet from the cold water
storage cistern, allowing roughly 1 psi for every 2 feet.
CS05
It makes no difference which way the drain hose
faces, either to the right or left of the dishwasher.
Avoid bending or kinking the hose as this could
prevent or slow down the discharge of water.
For making the connection
itself, the coupling nut fitted
to the machine's supply
hose is designed to screw
onto either a 3/4 inch gas
thread spout, or to a pur-
If you use a drain hose extension it must be no longer
than 2 metres and its internal diameter must be no
smaller than the diameter of the hose provided.
Likewise the internal diameter of the couplings used
for connection to the waste outlet must be no smaller
than the diameter of the drain hose.
pose made quick-coupling
tap such as the Press
A
Block.
CA04
Note: The sink plug must not be in place when the
machine is draining as this could cause the water to
siphon back into the machine.
PIN07GB
4
Download from Www.Somanuals.com. All Manuals Search And Download.
A replacement cover/carrier must be obtained from
your local Zanussi Service Force Centre whose
address is listed in the Customer Care Booklet which
accompanies your instruction manual.
The electrical connections
WARNING: THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability should
this safety measure not be observed.
This appliance complies with the follow-
ing E.E.C. Directives:
- 73/23 of 19.2.73 (Low Voltage Directive) and sub-
sequent modifications;
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
- 89/336 of 3.5.89 (Electromagnetic Compatibility
Directive) and subsequent modifications.
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to prevent
the hazard of shocks in case it should be plugged into
a 13 amp socket in another part of your home.
Please ensure that when the appliance is installed
it is easily accessible for the engineer in the event
of a breakdown.
Important
The wires in the mains lead are coloured in accor-
dance with the following code:
Green and Yellow
Blue
- Earth
- Neutral
- Live
Brown
If you fit your own plug, the colours of the wires in the
mains lead of your appliance may not correspond with
the markings identifying the terminals in your plug,
proceed as follows:
GREEN & YELLOW
13 AMP FUSE
BROWN
BLUE
CORD CLAMP
CE01
Connect the Green and Yellow (earth) wire to the ter-
minal in the plug which is marked with the letter «E»
or the earth symbol
or coloured green and yellow.
Connect the Blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
Connect the Brown (live) wire to the terminal in the
plug which is marked with the letter «L» or coloured
red.
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BSI362 fuse.
Only ASTA or BSI approved fuses should be used.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured in-
sert at the base of the plug.
PIN08GB
5
Download from Www.Somanuals.com. All Manuals Search And Download.
USE
Control panel
THE CONTROLS
1. ON/OFF Pushbutton
In this fully integrated appliance the controls are located
on the top of the door. When selecting a programme,
the door needs to be partially opened.
Depress this pushbutton to switch the dishwasher on.
The ON/OFF indicator light (3) illuminates indicating
that the washing programme can be selected and
started. Depress again this button to switch the appli-
ance off.
Audible signals have been introduced to help indicate
which operations the dishwasher is performing.
2. Salt Refill Indicator Light "SALT"
Short «instruction accepted» signal
This light illuminates when the salt container needs
refilling. This light will remain on in a soft water area
where salt is not required.
When any of the buttons are pressed: a short audible
signal informs you that the machine has accepted the
instruction given.
Long «programme run» signal
3. ON/OFF Indicator Light
A continuous audible signal lasting about one second,
heard only when you close the dishwasher door,
informs you that the washing programme is starting.
This illuminates when the ON/OFF button (1 ) is
depressed, indicating that the machine is on.
Intermittent «end of programme» signal
4. Programme Selector Buttons
An intermittent audible signal, lasting in total five sec-
onds, informs you that the wash programme has end-
ed. If you wish to deactivate these audible signals,
press both the NORMAL 65°c and ECONOMY 55°c
programme buttons together for about 3 seconds,
until the intermittent audible signal can no longer be
heard.
Depress the button corresponding to the desired
washing programme (see washing programme chart).
5 End of Cycle Indicator Light
This light flashes when the programme has finished.
To switch it off depress the ON/OFF pushbutton (1).
SO82
To reactivate the audible signals, press both buttons
together again for about 3 seconds, until an intermit-
tent audible signal is heard.
PPC21GB
6
Download from Www.Somanuals.com. All Manuals Search And Download.
- Press the programme button corresponding to the
required level.
The Water Softener
Water contains varying amounts of lime and mineral
salts depending on the area in which you live: these
are deposited on the dishes leaving white marks.
- 5 seconds after having last pressed any of the
programme buttons, the dishwasher memorises the
level selected and returns to the programme setting
mode.
The higher the content of these salts, the harder your
water will be. The «hardness» level is measured on 2
equivalent scales: Clarke degrees or French degrees.
Contact your local Water Authority to find the exact
water hardness level for your area.
Important
Salt MUST be used regularly from level 2 upward.
If your water is «level 1» it is already soft and there-
fore there is no need to use salt.
The dishwasher is equipped with a softener which uses
special dishwasher salt to provide lime-free (softened)
water. The softener can treat water hardness up to 90
French degrees via 5 adjustment levels.
Filling with Salt
Find on the table below the level corresponding to the
hardness of your water and the required adjustments:
Only use salt designed specifically for use in dish-
washers. Other types of salt contain high percentages
of other substances which may reduce the efficiency
of the softener.
Water hardness
Use of
salt
Level
°TH
French
degrees
°dH
Clarke
degrees
Unscrew the cap of the salt container.
Fill the container with 1 litre of water (this operation is
necessary only the first time).
**NO
0-14
15-39
40-50
51-70
71-90
0-10
11-27
28-35
36-49
50-63
1
YES
2
*
YES
YES
YES
3
4
5
Place approximately 1kg of dishwasher salt inside
using the funnel provided (see figure).
Replace the cap making sure that there is no trace of
salt on the screw thread or on the gasket.
* The water softener is factory set at level 2 as this suits most users.
** If you use phosphate free detergents containing enzymes, use
salt starting from 6 Clarke degrees (7 French degrees).
Screw the cap
tightly.
You may also change the factory setting by means of
the wash programme selector buttons. Each button
corresponds to a different level:
T
SAL
Level 1 = RINSE AND HOLD Programme Button
Level 2 = INTENSIVE 70°c Programme Button
Level 3 = NORMAL 65°c Programme Button
Level 4 = ECONOMY 55°c Programme Button
Level 5 = QUICK 55°c Programme Button
SR03
To select a different level, proceed as follows:
- Press the NORMAL 65°c and QUICK 55°c
programme buttons simultaneously for about 5
seconds until the short «instruction accepted»
signal is heard. The pilot light corresponding to the
current level flashes very rapidly.
When this has been done, all that is required is to
periodically add salt to the container. You are reminded
of this by the Salt refill light «SALT» on the control panel
which will illuminate when the salt has finished.
The salt container always has some water inside
which will normally overflow when refilling with salt.
Caution
Only fill with salt just before starting one of the com-
plete washing programmes (not Rinse and Hold
programme). This will prevent any grains of salt or
salty water, which may have been spilled, remaining
on the bottom of the machine for any period of time.
This could cause corrosion.
SO83
PAA12GB
7
Download from Www.Somanuals.com. All Manuals Search And Download.
To open the dispenser lid, pull the catch (D). This will
open it.
Rinse Aid
The use of this liquid ensures thorough rinsing, spot
and streak free drying, making the water run quickly
off the dishes for sparkling results. It is automatically
added during the hot rinse. The dispenser, which is
positioned inside the door, holds about 110 ml of rinse
aid, which is sufficient for 16-40 dishwashing
programmes, depending upon the dosage setting.
To help you to correctly
D
dose the right amount of
detergent, inside the con-
tainer there are two refer-
ence marks:
M A X
M I N
- MIN = 15 ml
- MAX = 30 ml
Filling with Rinse Aid
DE07
Open the container by turning the lid (A) anticlockwise.
The amount of detergent to be used varies depending
on how soiled the dishes are and the type of dishes
being washed. We recommend the amounts shown in
the programme chart on the next pages.
Add rinse aid until the container is completely full
(approx. 110 ml). The indicator (B) will be completely
dark.
Top up with rinse aid when the indicator (B) becomes
clear.
After filling the dispenser with detergent, close
the lid.
Remember to CLOSE the lid after every refill.
Caution
The programme with pre-
wash requires a small extra
amount of detergent of ap-
proximately 5g = half dessert
spoon to be poured over the
lid of the dispenser, as shown
on the picture.
Clean up any rinse aid spilt during filling with an
absorbent cloth to avoid excess foaming during the
next wash.
Adjusting the Dose
According to the finish and drying results obtained,
adjust the dose of rinse aid by means of the 6 position
selector (C) (position 1 - minimum dose, position 6
maximum dose). (Start from position 3). Gradually
increase the dose if there are drops of water or lime
spots on the dishes after washing. Reduce it if there
are sticky whitish streaks on the dishes.
DE02
For the intensive programme (suitable for particularly dirty
pans and dishes) an extra 10g of detergent must be
poured over the dispenser’s lid.
At the end of any washing programme the lid is always
open, ready for the next wash.
5
3
21
6
Since not all detergents are the same, you should also
consult the instructions on the packet.
C
Remember that insufficient quantities of detergent will
produce poor washing results whereas an excessive
amount of detergent does not improve washing results
and is also wasteful.
4
5
6
21
B
BR04
A
Using no more than the correct amount of detergent
also contributes to reducing pollution.
Caution: Do not put liquid detergent into the rinse aid
compartment
Phosphate free detergents with enzymes
Use of Detergent
These new compact powders are generally phosphate-
free. As phosphates have water softening properties,
we suggest you add salt to the salt container even If the
hardness of your water is as low as 6 Clarke degrees.
This will avoid lime deposits on crockery and the inner
tub.
Before starting any of the dishwashing programmes,
except for the rinse and hold programme, load the
detergent in the dispenser.
Use only tablets, powder or liquid detergents specifically
designed for domestic dishwashers.
Unsuitable detergents (such as those for washing by
hand) do not contain the right ingredients for machine
washing and hamper correct functioning of the
machine.
Zanussi recommends the use of Finish dishwasher
detergent.
PBR13GB
8
Download from Www.Somanuals.com. All Manuals Search And Download.
The two rear rows of prongs on the lower basket can
be easily lowered to allow you to load pots, pans and
bowls.
Loading your Machine
Before placing dishes in the machine, remove any
scraps of food from the plates (small bones,
toothpicks, fish bones, scraps of meat and vegetables,
fruit skins etc.) to avoid clogging the filters and
consequently reducing performance.
To lower the prongs:
slightly pull them upward
and let them drop down
(see picture); to bring them
back to the standing posi-
tion, just pull them up
again.
Open the door and slide out the baskets to load the
dishes.
Use of the Lower Basket
UI18
The lower basket is designed to take saucepans, lids,
plates (up to 27 cm in diameter), salad bowls, cutlery etc.
Serving dishes and large lids should be arranged
around the edge of the basket, ensuring that the
upper spray arm can turn freely.
Use of the Upper Basket
The upper basket is designed for plates (dessert plates,
saucers, dinner plates up to 24 cm in diameter), salad
bowls, cups and glasses; these should be
arranged as shown in the pictures. Glasses with long
stems can be placed upside-down in the raised cup-
racks.
UI23
IEC 436 / DIN 44990
US08
IEC 436 / DIN 44990
UI24
Cutlery should be placed in the removable cutlery
basket with the handles facing downwards. If the
handles protrude from the bottom of the basket,
obstructing the lower spray arm, load the cutlery with
the handles facing upward.
US07
The cup-rack on the left folds upwards to increase
your loading flexibility.
Mix spoons with the other
cutlery to prevent them
sticking together.
Teaspoons may be loaded
into the special slots
provided in the cutlery
basket handle.
Before closing the door, ensure that the spray
arms can rotate freely.
UI10
PCE12GB
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Height of the Upper Basket
If washing very large plates (over 27 cm and up to 31
cm in diameter) you can load them in the lower basket
after moving the upper basket to the higher position
as follows:
Move the front runner stops
(A) of the upper basket out-
A
ward and slide the basket
out.
Refit the basket in the higher
position and replace the
stops (A) in their original
position.
RC01
When the top basket is in the higher position it will only
take plates up to 20 cm in diameter and you will not be
able to use the raised cup racks.
HELPFUL HINTS
For Best Washing Results:
Items not Suitable for Dishwashers
Before loading, remove all scraps of food and soak
very heavily soiled pots and pans.
Always arrange saucepans, cups and glasses etc.
upside-down.
Tilt items with convex or concave surfaces so that the
water drains off easily.
The following should not be washed in the
dishwasher:
Cutlery or dishes with wooden or horn handles or
glued parts.
Handmade items, wooden objects, antiques or hand-
painted china.
Certain types of decoration can discolour when
washed in a dishwasher.
Crystal-ware and plastic objects, if not guaranteed
dishwasher-proof, should be washed by hand. You
are advised to place them in the upper basket and to
select a delicate programme.
Long items of cutlery such as ladles, carving knives
etc. should be positioned horizontally in the upper
basket.
Avoid contact between the dishes as far as possible;
correct arrangement of the items will give better
washing results.
Light items (plastic bowls etc.) should be loaded in the
upper basket and arranged so that they do not move
during washing.
Certain types of glass can also become opaque after
being washed several times in a dishwasher.
Silver cutlery tends to go black if mixed with steel
cutlery. Place it in the cutlery basket separate from the
others.
Iron and cast iron objects can rust and stain other
items.
Aluminium tends to go black; copper, pewter and
brass tend to stain.
You will improve drying results by leaving the
dishwasher door ajar for at least 15-30 minutes as
soon as the programme finishes.
Care must be taken when opening the door, as
steam will escape.
To Save Energy
Caution: You are advised not to load very small
items which can fall through the baskets.
Do not prewash dishes under running water.
Note: When buying new dishes, ensure that they are
dishwasher-proof.
Place dishes in the machine immediately after every meal
and wait until the dishwasher is full before washing.
If necessary run the Rinse and Hold programme (see
Programme Chart on the following pages), so that any
food scraps do not become caked on the dishes while
you are waiting to run the complete wash programme.
Select an ECONOMIC programme when the baskets
are not very full and/or when the dishes are not very
soiled, following the instructions given in the
Programme Chart (ECONOMY programmes, QUICK
programme).
PCL12GB
10
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHING PROGRAMMES
Recommended quantity of detergent
on the
dispenser
dispenser
lid
in the
Type of load and
degree of soil
Required
pushbuttons
Cycle
description
Programme
Cold rinse to prevent
food scraps from
drying up and sticking
to the dishes
RINSE & HOLD
RINSE &
HOLD
ON
OFF
—
—
Prewash at 55°C
Main wash at 70°C
2 cold rinses
1 hot rinse at 65°C
Hot air drying
1 level
INTENSIVE
70°c
1 heaped
dessert
spoonful
(15 g)
INTENSIVE Heavily soiled crockery,
ON
OFF
dessert
spoonful
(10 g)
70°c
pots, pans and cutlery
Cold prewash
Main wash at 65°C
1 cold rinse
1 hot rinse at 65°C
Hot air drying
1 heaped
dessert
spoonful
(15 g)
Half
NORMAL
65°c
Normally soiled crockery,
pots, pans, and cutlery,
NORMAL
65°c
ON
OFF
*
dessert
spoonful
(5 g)
ECONOMY
55°c
1 heaped
dessert
spoonful
(15 g)
Lightly soiled crockery,
pots and cutlery
Half
ECONOMY
55°c
Cold prewash
Main wash at 55°C
1 cold rinse
1 hot rinse at 65°C
Hot air drying
ON
OFF
dessert
spoonful
(5 g)
QUICK
55°c
1 heaped
dessert
spoonful
(15 g)
Lightly soiled crockery
Main wash at 55°C
1 cold rinse
1 hot rinse at 55°C
ON
OFF
QUICK
**
WASH
55°c
—
This programme is equivalent to IEC436 standard.
*
This is a special programme to wash in a short time (approx. 40 minutes) a full load of lightly soiled dishes,
**
glasses and crockery (except pots) so that you may re-use them promptly. Due to the shortness of this programme,
no drying phase is provided.
PTP18GB
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
1 Check that the filters are clean
7 Start the programme
(see cleaning instructions)
Open the water supply.
Close the dishwasher door. An audible signal of about 1
second advises you that the programme has started.
The indicator light which corresponds to the programme
under way is now permanently on.
2 Switch on the appliance at the mains
supply.
Caution
3 Check that there is salt and rinse aid
In general it is not advisable to open the door while the
machine is working; if the door is opened however, a
safety device ensures that the machine stops.
4 Load the dishes
If you need to stop the dishwasher at any moment
during the wash programme, switch the appliance off at
the plug; open the door and press the ON/OFF button.
Remove any scraps of food.
Pull the lower basket out and arrange the saucepans,
plates and cutlery in it.
Care must be taken if opening the door, as steam will
escape.
Pull the upper basket out and arrange the plates,
saucers, glasses and cups etc. in it.
8 At the end of the washing programme
Slide the baskets back into the machine.
Ensure that the spray arms can rotate freely.
The dishwasher will automatically stop and an inter-
mittent audible signal of about 5 sec. informs you that
the programme has finished.
5 Measure out detergent
Wait until the end of the signal before opening the
door.
Pour the required amount of detergent into the
dispenser according to the indications in the Washing
Programmes chart and close the lid.
Open the door. The End of Cycle indicator light flashes.
Depress the ON/OFF button to switch the dishwasher
off.
You are advised to turn off the water tap and switch
off the appliance at the plug socket.
6 Set the programme
The selection of a programme occurs with the door
partially opened.
Wait a few minutes before removing the dishes; in this
way they will be cooler and the drying will be improved.
Depress ON/OFF button (1); the ON/OFF indicator
light (3) comes on.
Empty the lower basket first and then the upper one;
this will avoid water dripping from the upper basket
onto the dishes in the lower one.
Depress the programme button which corresponds to
the washing programme you wish to select; the corre-
sponding indicator light will flash.
8 Cancel the wash programme
To change a wash programme in progress depress
the button corresponding to the programme you wish
to cancel for about 1 sec., until the relevant control
light goes out. The dishwasher is now reset and you
can select a new programme.
PSO04GB
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND CLEANING
Check that the spray arm nozzles are not obstructed.
To remove the bottom spray arm, release it from its
securing catches and pull it out.
Cleaning the Central Filters
(After each wash)
Inspect the central filters (B) and (C) and remove any
scraps of food with a brush, under running water.
Clean the external surfaces of the machine and
control panel with a soft damp cloth. If necessary use
only neutral detergents. Never use abrasive products,
scouring pads or solvents (acetone, trichloroethylene
etc...).
Filters (B) and (C) are both removed by lifting up the
outer one (B) (pulling the central funnel upwards); the
smaller filter (C) can then be removed by pressing the
two tongues (D).
The upper spray arm
The upper spray arm should not be removed for gen-
eral cleaning, however if a blockage occurs it can be
removed for cleaning as follows:
C
D
Slide out the upper basket.
Push downwards on the
water feed pipe, simultane-
ously push the spray arm
upwards and turn it in a
clockwise direction.
B
MA02
MA08
Once cleaned, refit the filters by pressing them
down until they click into place.
Cleaning the Large Filter
MA09
To reassemble the upper spray arm push downwards
on the water feed pipe, simultaneously push the spray
arm upwards and turn it anticlockwise.
(Once a month)
Clean the large filter (A) on both sides under running
water, using a brush.
To take it out, remove the spray arm by pressing the
two tongues (E), turn the ring (F) anticlockwise
(towards the left) and then slide the whole part out.
Refit the filter following the above instructions in
reverse order.
Prolonged Periods of Non-Operation
If you are not using the machine for any period of time
you are advised to:
unplug the appliance and turn off the water;
fill the rinse aid dispenser;
E
leave the door ajar to prevent the formation of
unpleasant smells;
A
leave the inside of the machine clean.
Frost Precautions
F
Avoid placing the machine in a location where the
temperature is below 0°C.
MA03
Caution: the dishwasher must not be used
without filters.
If this is unavoidable, empty the machine, close the
water inlet tap, disconnect the water inlet pipe and
empty it.
Incorrect repositioning of the filters will produce
poor washing results.
Moving the Machine
Cleaning of the filters is vital to ensure correct
operation of the machine.
If you have to move the machine (you are moving
house etc...):
Internal and External Cleaning
unplug it;
turn off the water tap;
You must ensure that the seals around the door, the
detergent and rinse aid dispensers are cleaned
regu larly with a damp cloth.
remove the water inlet and discharge hoses;
pull the machine out together with the hoses.
We recommend you carryout a maintenance wash
every 3 months, by running a 65° C wash programme
without dishes using detergent.
Caution: avoid over tilting the machine during
transport.
PMA08GB
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING
Certain problems are often due to lack of simple
maintenance or oversights and can be solved easily
without having to call out an engineer.
If the indicator light of the QUICK
programme is flashing
The dishwasher does not empty out water
If the machine will not start
■ The discharge pipe is bent.
Eliminate the bend (see instructions for connection
to the drain).
Switch off the dishwasher; switch it back on and
start the wash programme. If the alarm reappears,
call the Service Centre.
■ The door has not been properly closed.
■ The plug is not properly inserted in the power socket.
■ There is no current at the socket. Check the fuse.
This dishwasher may display a fault code in the pilot
lights of the programmes which will assist you in
identifying the fault. If the ON/OFF indicator light is
illuminated and one of the programme's indicator
light is flashing please carry out the following
checks.
■ The sink drain is blocked
Unblock the sink drain pipe.
Switch off the dishwasher; switch it back on and
start the programme. If the alarm reappears, call the
Service Centre.
■ The discharge pipe extension is not correct.
Carefully follow the instructions for "Connection to
the drain”.
Switch off the dishwasher; switch it back on and
start the wash programme. If the alarm reappears,
call the Service Centre.
If the pilot light of the RINSE & HOLD
programme is flashing
The dishwasher will not fill with water
■ The water tap is closed.
Open the tap. Switch off the dishwasher; switch it
back on and start the wash programme. If the alarm
reappears, call the Service Centre.
■ The wall drain connection has no breather.
Consult a qualified engineer.
■ Mains water supply cut off
Wait for the supply to be restored.
If the pilot light of the NORMAL OR
ECONOMY programme is flashing
Switch off the dishwasher; switch it back on and
start the wash programme. If the alarm reappears,
call the Service Centre.
■ General
Switch off the dishwasher; switch it back on and
start the wash programme. If the alarm reappears,
call the Service Centre.
■ Water feed pipe bent or squashed
Reposition the pipe (see instructions for connection
to the water supply).
Switch off the dishwasher; switch it back on and
start the wash programme. If the alarm reappears,
call the Service Centre.
The dishes are not clean (poor wash)
■ Filter in the water feed pipe clogged
Close the water tap, unscrew the water feed pipe
and thoroughly clean the filter. Screw the pipe back
on and open the water tap.
■ The baskets are too full.
■ The dishes have not been arranged properly.
■ The spray arms do not rotate.
Switch off the dishwasher; switch it back on and
start the wash programme. If the alarm reappears,
call the Service Centre.
■ The spray arms holes are clogged.
■ The filters are clogged.
■ Not enough detergent has been used or it is
unsuitable.
■ The detergent is old or has gone hard.
■ The salt container cap is not properly closed.
■ The washing programme selected is too gentle.
If the indicator light of the INTENSIVE
programme is flashing
■ The filters are clogged
Clean the filters (see MAINTENANCE section).
Check outlet hose is not blocked.
Visible lime deposits or white film on the dishes
■ There is no salt or the softener has not been adjusted
to the hardness of the water.
Check dishes are correctly loaded.
Switch off the dishwasher; switch it back on and
start the wash programme. If the alarm reappears,
call the Service Centre.
■ The rinse aid has run out or too little is being used.
The machine is noisy
■ The dishes are rattling against each other.
PRA03GB
14
Download from Www.Somanuals.com. All Manuals Search And Download.
The dishes are not quite dry
■ The dishes have been left too long inside the
machine.
The door is difficult to close
■ The dishwasher is not level or is not properly built-in.
If, after the above checks, the fault persists, call your
local Zanussi Service Centre, whose address can be
found in the accompanying Customer Care Booklet, and
can also be found in your local telephone directory
under «Z».
Please make sure you give the model and serial
number of the appliance. This information can be
found on the rating plate located on the right-hand
side of the dishwasher door (see picture).
Prod.No. ........ Ser. No. .........
Mod. ........
RA01
Original spare parts can be purchased from Zanussi
Service Centres.
In guarantee customers should ensure that the
above checks have been made as the engineer
will make a charge if the fault is not a mechanical
or electrical breakdown.
Please note that proof of purchase is required for any
guarantee service calls.
Service detail - adhesive label
When you return your guarantee card to Zanussi Ltd.,
you will receive a «Appliance Guarantee And
Maintenance Record» together with an adhesive label
(containing the telephone number of your local
Zanussi Service Centre). The label can be adhered to
the machine or adjacent furniture.
PRA04GB
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BUILDING-IN
Mounting of decor panel onto the door
Building-in features
The height of the panel depends on the height of the
plinth of adjacent kitchen units (see kitchen plinth
adjustment).
This dishwasher is designed to be fitted under a kitchen
counter or sink.
In either case, it is essential that the recess dimensions
indicated in the picture are followed.
No further openings for venting of the dishwasher are
required, but only to let the water fill and drain hoses
and power supply cable pass through.
The panel must be fitted
446 max
with a handle, as the dish-
washer handle will be hid-
den by the panel.
Drill the panel with a Ø
2x12 bit according to the
dimensions indicated in the
figure.
360
*
*
II27
Fix the cross bar onto the panel using four 3.5x16
screws provided. Reduce the length of fixing screws
according to thickness of panel.
II24
II06
If for aesthetic matching the panel is provided with a
false drawer (fitted or carved on the panel itself), the
two brackets provided should also be used.
The recess height may be anywhere between 820
and 880 mm from the floor since the dishwasher
incorporates levelling feet adjustable over a wide
range (max 60 mm).
Fix the brackets according
446 max
=
=
391,5
to the measurements
shown in the figure, by us-
ing four 3.5 x 16 screws.
Adjust the height of the appliance by turning these
feet.
A distance of 2 mm should be allowed between the
top of the dishwasher and the counter top.
Fitting under a counter (kitchen worktop
or sink)
II26
It is absolutely essential that the dishwasher is
disconnected from the electricity supply before gaining
access to any internal component.
Reduce the length of fixing screws according to
thickness of panel.
Mount the decor panel by
inserting the two pivots of
the cross-bar into the
slotted holes of the door.
Lift the decor panel until
perfect alignment with the
facia panel is obtained: if
the two brackets have also
Fit the dishwasher into the appropriate housing space
and connect it. Make sure that the water fill and drain
hoses and the power supply cable are not bent or
kinked.
Fitting the panel onto the door
The door on this model is designed for the overlay of
a panel having the following dimensions:
II12
been used, they will auto-
matically enagage in the
special holes provided on
the dishwasher door.
Width:
446 mm
Height:
Thickness:
Weight:
Note:
644 to 714 mm max
20 mm max
1.5 to 6 kg max
Once the correct position
has been found, open the
door and fasten the decor
panel on the lower section
by means of the two long
4x40 screws provided,
using the holes through the
inner door (see fig.).
The panel height should not be more than what
indicated, otherwise complete opening of the door will
no longer be possible as the panel hits against the
dishwasher plinth.
II10
PII05GB
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Securing under a counter
Levelling
Secure the dishwasher to
Make sure that the dishwasher door closes properly,
without rubbing on sides. Otherwise level the machine
by slightly screwing or unscrewing the two front feet
until perfect closure of the door is reached.
the counter on the front
part by means of two
4,2x13 screws provided
(see fig. - point A).
A
Kitchen plinth adjustment
To allow correct opening of
the door it is sometimes
necessary to cut the
kitchen plinth. Refer to the
cutting table below.
II03
Important!
The dishwasher must be secured against tilting.
Therefore, make sure that the counter it is fitted
under, is suitably secured to a fixed structure
(adjacent kitchen cabinets, wall).
II13
According to dimensions of
(a) and (b) as shown on
the figure, you will find on
the following table the
depth (x) of the cut to be
made on the plinth.
Attention!
When the dishwasher is secured to the kitchen
cabinets, do not drill any holes into the sides of
the machine.
Adjusting the door balance
a
After fitting the door panel, the adjustment of the door
balance may be necessary.
b
II15
The door of the dishwasher is balanced when it is
open in any position.
The dimensions (a) and (b) of the table are those
more frequently used in the kitchen furnitures.
For this purpose use the
two front screws. Open the
door, remove the caps and
45°
screw or unscrew the
Height (a)*
screws.
In this way the tension of
the door balancing springs
is increased or decreased
respectively. Insert the
caps again.
170 160 150 140 130 120 110 100
40
50
136 131 125 118 110 100 93 85
135 131 125 118 110 102 92 85
137 132 125 118 110 102 94 85
138 134 128 120 110 104 95 85
II09
60
Attention!
70
X
The weight of the panel should be within the limits
given in the "dimensions of the panel", otherwise
balancing the door will not be possible.
80
/
/
/
139 130 124 115 105 98 88
90
/
/
138 129 120 110 100 90
100
/
135 125 115 105 95
*dimensions in mm
450 mm
(minimum)
X
Dimensions of the cut on the plinth
PII06GB
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PEACE OF MIND FOR TWENTY FOUR MONTHS
Zanussi guarantee conditions
Exclusions
This guarantee is in addition to your statutory and
other legal rights.
This guarantee does not cover:
■ Damage or calls resulting from transportation,
improper use or neglect, the replacement of any
light bulbs or removable parts of glass or plastic.
We, Zanussi Ltd., undertake that if, within twentyfour
months of the date of the purchase, this ZANUSSI
appliance or any part thereof is proved to be defective
by reason only of faulty workmanship or materials, we
will, at our option, repair or replace the same FREE
OF ANY CHARGE for labour, materials or carriage on
condition that:
■ Costs incurred for calls to put right machines
improperly installed or calls to machines outside the
UK and the Republic of Ireland.
■ Appliances found to be in use within a commercial
or similar environment, plus those which are the
subject to rental agreements.
■ The appliance has been correctly installed and used
only on the electricity supply stated on the rating
plate.
■ Products of Zanussi manufacture which are NOT
marketed by Zanussi Ltd.
■ The appliance has been used for normal domestic
purposes only, and in accordance with the manufac-
turer's operating and maintenance instructions.
■ EU Countries - The standard guarantee is applica-
ble but subject to the owner's responsibility and cost
to ensure the appliance meets the standards set by
the country to which the product is taken.The
Zanussi company in the country concerned will be
pleased to advise further. Sight of your purchase
receipt will be required by them.
■ The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any
person not authorised by us.
All service work under this guarantee must be under-
taken by a Zanussi Service Force Centre.
Home visits are made between 8.30 am and 5.30 pm
Monday to Friday. Visits may be available outside
these hours in which case a premium will be
charged.
Any appliance or defective part replaced shall
become our property.
PGA05GB
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
Printed in Italy
0/1096
152995 81/0
Download from Www.Somanuals.com. All Manuals Search And Download.
|