DISHWASHER
DA 6142
DA 6142 S
Instruction Book
152969 91/0
UK
Download from Www.Somanuals.com. All Manuals Search And Download.
In daily use
G Check if it’s necessary to refill with special salt or rinse aid
G Load cutlery and dishes into the dishwasher.
G Fill with dishwasher detergent .
Loading cutlery and dishes
Sponges, household cloths and any object that can
absorb water may not be washed in the dishwasher.
G Select a wash programme suitable for the cutlery and
G Before loading the dishes, you should:
- Remove large left-overs.
dishes.
G Start the wash programme.
- Soften remnants of burnt food in pans
G When loading the dishes and cutlery, please note:
- Dishes and cutlery must not impede the rotation of the
spray arms .
- Load hollow items such as cups, glasses, pans, etc. with
the opening downwards so that water cannot collect in the
container or a deep base.
- Dishes and items of cutlery must not lie inside one
another, or cover each other.
- To avoid damage to glasses, they must not touch.
- Lay small objects in the cutlery basket.
G Plastic items and pans with teflon have a tendancy to
retain water drops; these items will not dry as well as
porcelain and steel items.
For washing in the dishwasher the following cutlery/dishes
are not suitable:
are of limited suitability:
- Cutlery with wooden, horn, china or
mother-of-pearl handles
- Only wash stoneware in the dishwasher if it is specifically
marked as being dishwasher-safe by the manufacturer.
- Plastic items that are not heat resistant
- Glazed patterns may fade if machine washed frequently
- Older cutlery with glued parts that is not
temperature resistant
- Silver and aluminium parts have a tendency to discolour
during washing. Left-overs, e.g. egg white, egg yolk and
mustard often cause discolouring and staining on silver.
Therefore always clean left-overs from silver immediately, if
it is not to be washed straight after use.
- Bonded cutlery items or dishes
- Pewter or copper items
- Lead crystal glass
- Some types of glass can become dull after a large number
of washes
- Steel items subject to rusting
- Wooden platters
- Items made from synthetic fibres
Open the door and slide out the baskets to load the dishes.
The cutlery basket
Long bladed knives stored in an upright position are a
potential hazard.
Long and/or sharp items of cutlery such as carving knives
must be positioned horizontally in the upper basket.
Take care when loading or unloading sharp items such as
knives.
The lower basket
The lower basket is designed to take saucepans, lids, plates,
salad bowls, cutlery etc.
Serving dishes and large lids should be arranged around the
edge of the basket, ensuring that the sprays arm can turn
freely.
Cutlery should be placed in the removable cutlery basket with
the handles facing downwards. If the handles protrude from
the bottom of the basket, obstructing the lower spray arm, load
the cutlery with the handles facing upwards.
Mix spoons with other cutlery to prevent them from sticking
together.
For best results we
recommend you to use the
cutlery grids provided (if the
size and dimensions of the
cutlery allow it).
UI21
UI48
UI63
3
Download from Www.Somanuals.com. All Manuals Search And Download.
The cutlery basket is in two
parts which can be
Before closing the door, ensure that the spray arms can
rotate freely.
separated to give greater
loading flexibility. To separate
the two parts, slide them
horizontally in opposite
directions and pull them
apart.
Adjusting the height of the upper basket
If washing very large plates you can load them in the lower
basket after moving the upper basket to the higher position.
To reassemble, reverse the
procedure.
Maximum height of the dishes in
upper basket
lower basket
UI62
With upper basket raised
With upper basket lowered
20 cm
24 cm
31 cm
27 cm
The upper basket
The upper basket is designed for plates (dessert plates,
saucers, dinner plates of up to 24 cm in diameter), salad
bowls, cups and glasses.
To move to the higher position proceed as
follows:
Arrange items on and
underneath the cup racks so
that water can reach all
surfaces.
1. Move the front runner stops (A) of the upper basket
outwards and slide the basket out.
2. Refit the basket in the higher position and replace the stops
Glasses with long stems can
be placed upside down in the
cup rack.
Light items (plastic bowls
etc.) must be loaded in the
(A) in their original position.
When the basket is in the
higher position you will not
be able to use the cup
rack(s).
US64
upper basket and arranged
so they do not move.
In case that plates are loaded in the upper
basket:
load them starting from the
rear positions of the
basket; tilting them slightly
forwards and avoiding the
front positions near the
door.
RC01
After loading your machine always close the door, as an
open door can be a hazard.
US71
Hints for test centres
Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme (see "Washing
programmes" chart).
Test in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and
rinse aid respectively and using the test programme (see "Washing programmes" chart).
Load:
12 standard place settings
Rinse aid setting
Rinse aid dispenser (type A):
Rinse aid dispenser (type B):
position 4 (Type III)
position 5 (Type III)
Detergent dosage :
5 g + 25 g (Type B)
Arrangement upper basket
Arrangement lower basket
4
Arrangement cutlery basket
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing programmes
Programme
Degree of soil
and
Starting position
of the programme
selector dial
Cycle
description
(3) Consumption values
Programme
Energy
Water
duration
consumption consumption
type of load
(in minutes)
(in kWh)
(in litres)
Cold prewash
Heavy soil.
Crockery, cutlery,
pots and pans
Main wash up to 65°C
1 cold rinse
1 hot rinse
(1) Intensive
110 - 120
1,15 - 1,24
16 - 18
A
65°c
Drying
Main wash up to 65°C
1 cold rinse
1 hot rinse
Normal soil.
Crockery and cutlery
B
C
Normal 65°c
95 - 105
30 - 40
1,15 - 1,24
1,05 - 1,15
13 - 15
11 - 13
Drying
Main wash up to 65°C
1 hot rinse
Fresh soil.
Crockery and cutlery
(2) Quick 65°c
Any.
1 cold rinse (to avoid
food scraps from
sticking together).
Partial load (to be
completed later in
the day).
12
0,1
10
Rinse and Hold
D
(1) Testing programme for EN 50242 (see "Hints for Test Centres").
(2) Ideal for washing crockery and cutlery of breakfast and dinner (fresh soil).
Characterised by a duration of about 30 minutes and a washing temperature of 60°C.
The time value is approximate and depends on the pressure and the temperature of the water and also by the variations
of the power supply.
This is the perfect daily programme, made to meet the needs of a family of 4 persons who only wish to load breakfast
and dinner crockery and cutlery.
(3) The consumption values are intended as a guide and depends on the pressure and the temperature of the water and also by
the variations of the power supply.
Starting a washing programme
G Press the On/Off push button (in this case the On/Off
indicator light turns off). Press the On/Off push button
again; the programme will start from the point in which it
1. Check that the baskets have been
loaded correctly and that the spray
was interrupted.
arms can rotate freely
6. End of the washing programme
2. Turn on the water tap
The dishwasher will automatically stop.
Switch off the dishwasher by pressing the On/Off push
button, the On/Off indicator light turns off.
Open the door and wait a few minutes before removing the
dishes; in this way they will be cooler and the drying will be
improved.
Water may appear on the sides and the door of the
dishwasher as the stainless steel will eventually become
cooler than the dishes.
3. Close the dishwasher door
4. Setting and starting the programme
Turn the programme selector dial clockwise until the letter
of the programme you wish to select corresponds with the
programme marker on the control panel (see "Washing
programmes" chart).
Press the On/Off push button; the On/Off indicator light will
illuminate and the programme will start automatically.
Unloading the dishwasher
Hot dishes are sensitive to knocks. The dishes should
therefore be allowed to cool down before removing from
the appliance.
Empty the lower basket first and then the upper one; this
will avoid water dripping from the upper basket onto the
dishes in the lower one.
5. To interrupt a washing programme in
progress
Interrupt a washing programme in progress ONLY if it’s
absolutely necessary
Attention! Hot steam may escape when the door is
opened. Open the door carefully.
G Open the dishwasher door; the programme will stop.
Close the door; the programme will start from the point in
which it was interrupted.
When the washing programme has finished, it is
recommended that the dishwasher is unplugged and the
water tap turned off.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Service and Spare Parts
In the event of your appliance requiring service, or if you wish
to purchase spare parts please contact your local Service
Force Centre by telephoning:
Please note that a valid purchase receipt or guarantee
documentation is required for in-guarantee service calls.
08705 929929
Customer Care
Department
For general enquiries concerning your Zanussi Electrolux
appliance or for further information on Zanussi Electrolux
products please contact our Customer Care Department by
letter or telephone at the address below or visit our website at
Your telephone call will be automatically routed to the Service
Force Centre covering your post code area.
For the address of your local Service Force Centre and further
information about Service Force, please visit the website at
Before calling out an engineer, please ensure you read the
details under the heading "What to do, when...".
When you contact the Service Force Centre you will need to
give the following details:
Customer Care Department
Zanussi Electrolux
55-77 High Street
Slough
Berkshire
SL1 1DZ
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found on the
Tel: 08705 727727 ( )
*
rating plate)
5. The purchase date
calls to this number may be recorded for training purposes
*
Guarantee Conditions
Standard Guarantee Conditions
European Guarantee
We, Zanussi Electrolux, undertake that if within 12 months of
the date of purchase this ZANUSSI ELECTROLUX appliance
or any part thereof is proved to be defective by reason only of
faulty workmanship or materials, we will, at our option repair or
replace the same FREE OF CHARGE for labour, materials or
carriage on condition that:
If you should move to another country within Europe then your
guarantee moves with you to your new home subject to the
following qualifications:
G The guarantee starts from the date you first purchased your
product.
G The guarantee is for the same period and to the same extent
for labour and parts as exists in the new country of use for
this brand or range of products.
G The appliance has been correctly installed and used only on
the electricity supply stated on the rating plate.
G The appliance has been used for normal domestic purposes
only, and in accordance with the manufacturer’s instructions.
G This guarantee relates to you and cannot be transferred to
another user.
G The appliance has not been serviced, maintained repaired,
taken apart or tampered with by any person not authorised
by us.
G Your new home is within the European Community (EC) or
European Free Trade Area.
G The product is installed and used in accordance with our
instructions and is only used domestically, i.e. a normal
household.
G All service work under this guarantee must be undertaken by
a Service Force Centre.
G Any appliance or defective part replaced shall become the
Company’s property.
G The product is installed taking into account regulations in
your new country.
G This guarantee is in addition to your statutory and other legal
rights.
Before you move please contact your nearest Customer Care
centre, listed below, to give them details of your new home.
They will then ensure that the local Service Organisation is
aware of your move and able to look after you and your
appliance.
Home visits are made between 8.30am and 5.30pm Monday
to Friday. Visits may be available outside these hours in which
case a premium will be charged.
Exclusions
This guarantee does not cover:
France
Senlis
+33 (0) 344 62 29 29
+49 (0) 800 234 7378
+39 (0) 434 39 4700
+46 (0) 8 672 53 90
+44 (0)1753 219897
+353 (0) 14090753
Germany Nurnberg
G Damage or calls resulting from transportation, improper use
or neglect, the replacement of any light bulbs or removable
parts of glass or plastic.
Italy
Pordenone
Stockholm
Slough
Sweden
UK
G Costs incurred for calls to put right an appliance which is
improperly installed or calls to appliances outside the United
Kingdom.
Ireland
Dublin
G Appliances found to be in use within a commercial
environment, plus those which are subject to rental
agreements.
G Products of Zanussi Electrolux manufacture which are not
marketed by Zanussi Electrolux.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Fitting under a counter
(kitchen worktop or sink)
By removing the machine’s worktop, you can install it under a
close fitting sink unit or a pre-existing top, providing the
dimensions of the recess correspond to those shown in the
picture.
600
IN05
Proceed as follows:
Remove the machine’s worktop by unscrewing the two rear
retaining screws, pull from the front and slide out the rear
slots, lifting the worktop.
Insert the machine after adjusting height and levelling with the
adjustable feet. When inserting the machine, ensure that the
water inlet and drain hoses are not kinked or squashed.
If the dishwasher is later used as a free-standing appliance,
the original worktop must be re-mounted.
The plinth on free-standing appliances is not adjustable.
Levelling
Good levelling is essential for correct closure and sealing of
the door.
When the appliance is correctly levelled, the door will not catch
on either side of the cabinet.
If the door does not close correctly, loosen or tighten the
adjustable feet until the machine is perfectly level.
Technical specifications
Dimensions
Width
60 cm
85 cm
82 cm
Height with worktop
Height without worktop
Max depth
63.5 cm
118.5 cm
Max depth with open door
Electrical connection:
Voltage
Information on the electrical connection is given on the rating plate on the
inner edge of the dishwasher’s door.
Overall power
Fuse
Water supply pressure
Minimum
Maximum
50 kPa (0.5 bar)
800 kPa (8 bar)
Water supply connection
Capacity
cold water
12 place settings
This appliance complies with the following E.E.C. Directives:
- 73/23 or 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 or 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
From the Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen,
cleaning and outdoor use. More than 55 million Electrolux Group products (such as
refrigerators, cookers, vacuum cleaners, chain saws and lawn mowers) are sold each year
to a value of approx. 14 billion USD in more than 150 countries around the world.
©
Subject to change without notice
Electrolux plc 2003
0 04/03
Download from Www.Somanuals.com. All Manuals Search And Download.
Instruction book - Part 1
Dishwasher
Before use
Maintenance
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Safety instructions
2
3
3
What to do, when...
Service and spare parts
8
9
Disposal
Installation instructions
Water supply connections
Water outlet hose connection
Electrical connection
10
10
10
11
Economical and ecological dishwashing
Prior to using for the first time
The water softener
Setting the water softener
Filling with salt
Rinse aid
Use of detergent
3
3
3
3
4
6
Maintenance and cleaning
Cleaning the filters
Prolonged periods of non-operation
Frost precautions
7
7
7
7
7
Moving the machine
Safety instructions
It is most important that this instruction book should be
retained with the appliance for future reference. Should
Your dishwasher in day-to-day use
G Items that are contaminated by petrol, paint, steel or iron
debris, corrosive, acidic or alkaline chemicals must not be
washed in this dishwasher.
the appliance be sold or transferred to another owner, or
should you move house and leave the appliance, always
ensure that the book is left with the appliance in order that
the new owner can get to know the functioning of the
appliance and the relevant safety information.
G Under no circumstances should you open the door whilst
the appliance is in operation, especially during the washing
phase, hot water may escape. However, if the door is
opened, a safety device ensures that the machine stops.
This information has been provided in the interest of your
safety. You MUST read it carefully before installing or
using the appliance.
G Only use products (detergent, salt and rinse aid) specifically
designed for use in dishwashers.
G Long bladed knives stored in an upright position are a
Installation
G Check your dishwasher for any transport damage. Never
connect a damaged machine. If your dishwasher is
damaged, you should contact your supplier.
potential hazard.
G Long and/or sharp items of cutlery such as carving knives
must be positioned horizontally in the upper basket.
G When finishing loading or unloading close the door, as an
G For safety reasons it is dangerous to alter the specifications
open door can be a hazard.
or attempt to modify this product in any way.
G Do not sit or stand on the open door.
G Any electrical and plumbing work required to install this
appliance should be carried out by a qualified and
competent person.
G Isolate the appliance from the power supply and turn off the
water supply after use.
G The appliance should not be connected to the electrical
G This product should be serviced by an authorised service
supply by means of an extension cable.
engineer, and only genuine spare parts should be used.
G Care must be taken to ensure that the appliance does not
G Under no circumstances should you attempt to repair the
machine yourself. Repairs carried out by inexperienced
persons may cause injury or serious malfunctioning.
Contact your local consumer services department. Always
insist on genuine spare parts.
stand on the electrical supply cable.
G The sides of the dishwasher must never be drilled to
prevent damage to hydraulic components.
Child safety
G This appliance is designed to be operated by adults.
G Children should not be allowed to tamper with the controls
or play with the product.
G Packaging parts may be dangerous for children, who could
even be suffocated! You should therefore keep all
packaging well away from children.
G The water in your dishwasher is not for drinking. Detergent
residues may still be present in your machine. Keep
children well away from your dishwasher when the door is
open.
G Keep all detergents in a safe place out of children's reach.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
For the disposing of the appliance please take it to a recycling
centre or to your dealer who will, for a small contribution to the
costs, dispose it for you.
Disposal
Dispose of the dishwasher packaging material correctly.
All packaging materials can be recycled.
Plastic parts are marked with standard international
abbreviations:
>PE<
>PS<
for polyethylene, e.g. sheet wrapping material.
for polystyrene, e.g. padding material (always CFC-
free).
Economical and
ecological dishwashing
>POM< for polyoxymethylene, e.g. plastic clips.
Cardboard packaging is manufactured from recycled paper
and should be deposited in the waste paper collection for
recycling.
G Ensure that the water softener is correctly adjusted.
G Do not pre-wash under running water.
G Select the wash programme to suit the nature and degree of
As and when you cease to use your dishwasher and withdraw
it from service, your should render it unserviceable before
having it disposed of.
the soiling on the dishes.
G Do not use more detergent, special salt and rinse aid than is
recommended in these operating instructions and by the
manufacturer of the respective product.
Warning! Children at play could lock themselves in your
dishwasher or otherwise endanger their lives. Therefore cut off
the power supply cable and make the door closing device
unusable to prevent children from being trapped inside.
Prior to using for the first time
Before using your dishwasher for the first time:
Only for dishwasher models with salt refilling
indicator light:
1. Ensure that the electrical and water connections comply
If the water softener has been adjusted on level 1 and no salt
is being used, the salt refilling indicator light on the control
panel, will always remain illuminated when the machine is
switched on.
with the installation instructions
2. Remove all packaging from inside the appliance
3. Set the water softener
4. Pour 1 litre of water inside the salt container and then fill
with salt
Setting the water softener
5. Fill the rinse aid dispenser
1. Open the dishwasher door.
6. Run a "Rinse and Hold" programme (not all models of
dishwashers are foreseen with this programme)
2. Remove the lower basket from the dishwasher.
3. Turn the water hardness switch until the required level (see
table) corresponds with the marker .
The water softener
4. Replace the lower basket.
The dishwasher is equipped with a water softener designed to
remove minerals and salts from the water supply, which would
have a detrimental or adverse effect on the operation of the
appliance.
The higher the content of these salts, the harder your water is.
Water hardness is measured in equivalent scales, German
degrees, French degrees and PPM (parts per Million).
The softener should be adjusted according to the hardness of
the water in your area. Your local Water Authority can advise
you on the hardness of the water in your area.
AA08
The dishwasher is factory set at position 2.
Water hardness
Water
hardness
setting
Use of
salt
Filling with salt
°TH
°dH
PPM
french degrees
71 - 90
51 - 70
31 - 50
8 - 30
german degrees
parts per million
Special salt can be added in one of two ways:
yes
yes
yes
yes
no
41 - 50
30 - 40
19 - 29
4 - 18
< 4
level 5
level 4
level 3
level 2
level 1
701 - 900
501 - 700
301 - 500
80 - 300
< 80
G
If you are using dishwasher detergent that already contains
salt, the detergent including the salt is placed in the
detergent compartment.
- In this case the water softener must be set to level 1 to
ensure that the special salt is taken from the detergent
container only.
< 8
G
If you are using dishwasher detergent and salt separately,
the special salt is to be put into the salt container.
- In this case the water softener must be set to between
level 1 and 5 (depending on the water hardness in your
area) to ensure that the special salt is taken from the salt
container only.
If your water is below level 1 it is already soft and therefore
there is no need to use salt. In this case adjust the water
softener on level 1 without using salt.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Only use salt specifically designed for use in
dishwashers.
All other types of salt not specifically designed for use in
a dishwasher, especially table salt, will damage the water
softener.
Only fill with salt just before starting one of the washing
programmes (except the Rinse and Hold programme).
This will prevent any grains of salt or salty water, which
may have been spilt, remaining on the bottom of the
machine for any period of time, which may cause
corrosion.
Rinse aid
Rinse aid is automatically added during the last rinse, ensuring
thorough rinsing, and spot and streak free drying. The
dispenser, which is positioned inside the door, holds about
110 ml of rinse aid, which is sufficient for 16 - 40 dishwashing
programmes, depending upon the dosage setting.
Rinse aid can be added in one of two ways:
G
If you are using dishwasher detergent that already contains
rinse aid, the detergent including the rinse aid is placed in
the detergent compartment.
To fill:
- In this case the rinse aid compartment must be empty.
If in the rinse aid dispenser there is still rinse aid you
must wait until it has finished before using detergent that
contains rinse aid.
1. Open the door, remove the lower basket and unscrew the
cap of the salt container by turning it anticlockwise.
2. Pour 1 litre of water inside the container (this is necessary
only before filling with salt for the first time).
G
If you are using dishwasher detergent and rinse aid
separately, the rinse aid is to be put into the rinse aid
dispenser.
3. Using the funnel provided,
pour in the salt until the
container is full.
SALE
- In this case the rinse aid dosage must be set in position
from 1 to 6 (see "Adjusting the dose").
T
ZOUT
SAL
SALZ
SEL
4. Replace the cap making
sure that there is no trace
of salt on the screw
Filling with rinse aid
thread or on the gasket.
(Rinse aid dispenser type A)
5. Screw on the cap tightly
turning it clockwise until it
stops with a click.
1. Open the container by pressing the release button (A).
SR14
2. Fill with rinse aid exactly up to the level indicator marked
"max".
The salt container will require topping up periodically.
According to the model of dishwasher, you are reminded
of this by:
A) The salt cap has a refill indicator window in the centre.
A green float is clearly visible when there is salt inside the
container and almost disappears when the salt has finished
reminding you to add salt.
BR07
BR14
Ensure that the lid is closed after every refill.
Adjusting the dose
According to the finish and drying results obtained, adjust the
dose of rinse aid by means of the 6 position selector (position
1 minimum dosage, position 6 maximum dosage).
SR22
Increase the dose if there are drops of water or lime spots on
the dishes after washing.
B) A salt indicator light on the control panel will come on
when the salt has finished.
The dose is factory set in position 4.
The salt indicator light on the control panel can remain
illuminated for 2-6 hours after the salt has been replenished,
assuming the dishwasher remains switched on. If you are
using salts that take longer to dissolve then this can take
longer. The function of the machine is not affected.
Reduce it if there are sticky whitish streaks on the dishes.
Do not worry if water over flows from the unit when filling with
salt, this is quite normal.
BR09
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Filling with rinse aid
Top up with rinse aid when:
1. The indicator (B) becomes clear,
(Rinse aid dispenser type B)
1. Open the container by turning the lid (A) anticlockwise.
2. Fill with rinse aid exactly up to the level indicator marked
"max".
BR03
BR11
2. Only for dishwasher models with rinse aid indicator
light:
BR01
BR13
When the rinse aid indicator light on the control panel
illuminates (when the machine is switched on).
Ensure the lid is closed after every refill.
Clean up any rinse aid spilt during filling with an absorbent
cloth to avoid excess foaming during the next wash.
Adjusting the dose
According to the finish and drying results obtained, adjust the
dose of rinse aid by means of the 6 position selector (C)
(position 1 minimum dosage, position 6 maximum dosage).
Only use branded rinse aid for dishwashers. Never fill the rinse
aid dispenser with any other substances (e.g. dishwasher
cleaning agent, liquid detergent). This would damage the
appliance.
Increase the dose if there are drops of water or lime spots on
the dishes after washing.
The dose is factory set in position 5.
Reduce it if there are sticky
whitish streaks on the
dishes.
BR02
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Use of detergent
Detergent tablets
Only use detergents specifically designed for use in
dishwashers.
Detergent tablets of different brands dissolve at different
speeds. For this reason some detergent tablets cannot
develop their full cleaning power during short programmes.
Therefore please use normal programmes with prewash when
using detergent tablets.
Using no more then the correct amount of detergent
contributes to reducing pollution.
Prior to the start of a wash programme (not for the "Rinse and
Hold" programme). The detergent is released during the
washing phase.
Do not place the tablets in the tub or in the cutlery basket
as this will result in poorer wash results. The tablets
should be placed in the detergent dispenser.
Please observe the manufacturer’s dosing and storage
recommendations as stated on the detergent packaging.
Concentrated detergent
Based on their chemical composition, dishwasher detergents
can be split into two basic types:
Fill with detergent
(Detergent dispenser type A)
- conventional, alkaline detergents with caustic components.
- low alkaline concentrated detergents with natural enzymes.
1. If the lid is closed: press release button (1).
The lid springs open.
The use of 50°C washing programmes in conjunction with
concentrated detergents reduces pollution and is good for your
dishes; these wash programmes are specially matched to the
dirt-dissolving properties of the enzymes in the concentrated
detergent. For this reason 50°C wash programmes in which
concentrated detergents are used can achieve the same
results that can otherwise only be achieved using 65°C
programmes.
2. Fill the detergent dispenser (2) with detergent.
The marking indicates the dosing levels:
20 = approximately 20 ml of detergent
30 = approximately 30 ml of detergent
3. All programmes with prewash need an additional detergent
dose (5/10 g) that must be placed in the prewash detergent
chamber (3). This detergent will take effect during the
prewash phase.
Use of "3 in 1" combi detergent tablets
General advice
These products are tablets with combined detergent/rinse-aid
and salt functions.
1. Before using these products you should first check that the
water hardness in your supply is compatible with the use of
these products as per the detergent manufacturers (on the
product packaging).
DE19
DE22
2. These products should be strictly used according to the
4. Close the lid and press until it locks in place.
detergent manufacturers instructions.
3. If you encounter problems when using 3 in 1 products for
the first time then please contact the detergent
manufacturers care line (the telephone number is given on
the product packaging).
Fill with detergent
(Detergent dispenser type B)
Special advice
1. Open the dispenser by pulling the catch (D).
When using combination products, the rinse-aid and salt
indicators are no longer useful (please note that only some
dishwashers have these options).
The lid springs open.
2. Fill the detergent dispenser with detergent.
The marking indicates the dosing levels:
For more information please refer to the instruction manual.
Min = approximately 15 g of detergent
Max = approximately 30 g of detergent
If you decide to turn back to the use of the standard detergent
system we advise that you:
3. Close the lid and press until it locks in place.
G Refill both the salt container and rinse aid dispenser.
G Switch the water hardness setting to the highest possible
position and run a normal washing programme without a
load.
G Readjust the water hardness setting again according to the
hardness of the water in your area.
DE02
DE17
4. All programmes with prewash need an additional detergent
dose (5/10 g) that must be placed over the lid of the
dispenser. This detergent will take effect during the prewash
phase.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and cleaning
Clean the external surfaces of the machine and control panel
with a damp soft cloth. If necessary use only neutral
detergents. Never use abrasive products, scouring pads or
solvent (acetone, trichloroethylene etc....).
8. Place the coarse/fine filter in the microfilter and press
together.
9. Put the filter combination in place and lock by turning the
handle clockwise to the stop. During this process ensure
that the flat filter does not protrude above the base of the
washing compartment.
Ensure that the seals around the door, the detergent and rinse
aid dispensers are cleaned regularly with a damp cloth.
We recommend every 3 months to run a 65°C wash
programme without dishes using detergent.
Under no circumstances may the dishwasher be used
without filters.
Incorrect repositioning and fitting of the filters will
produce poor washing results.
Cleaning the filters
The filters in the base of the washing compartment are to a
large extent self-cleaning. Nevertheless the filters should be
checked and cleaned from time to time. Dirty filters will
degrade the washing result.
To ensure a correct
working of the dishwasher,
NEVER try to remove the
upper spray arm.
1. Open the door, remove the lower basket.
If residues of soil have
clogged the holes in the
upper spray arm, remove
them with a toothpick.
MA33
2. The dishwasher filter system comprises a coarse/fine filter
(A/B), a microfilter (C) and a flat filter (D).
Some dishwasher models filter system comprises only a
coarse filter (A), a microfilter (C) and a flat filter (D).
Unlock the filter system using the handle on the microfilter,
and remove.
Prolonged periods of non-operation
If you are not using the machine for any period of time you are
advised to:
1. Unplug the appliance and then turn off the water.
2. Fill the rinse aid dispenser.
3. Leave the door ajar to prevent the formation of any
unpleasant smells.
4. Leave the inside of the machine clean.
MA35
MA32
1
4
3. Turn the handle about / a turn anticlockwise and remove.
Frost precautions
Avoid placing the machine in a location where the temperature
is below 0°C. If this is unavoidable, empty the machine, close
the appliance door, disconnect the water inlet pipe and empty
it.
Moving the machine
MA36
If you have to move the machine (moving house etc....):
1. Unplug it.
2. Turn the water tap off.
4. Take hold of the coarse/fine filter (A/B) by the handle with
the hole and remove from the microfilter (C).
3. Remove the water inlet and discharge hoses.
4. Pull the machine out together with the hoses.
Avoid over tilting the machine during transportation.
5. Clean all filters thoroughly under running water.
6. Remove the flat filter (D) from the base of the washing
compartment and clean both faces thoroughly.
MA31
7. Put the flat filter back in the base of the washing
compartment.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
What to do, when...
Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the instructions
given here, without calling out an engineer.
...there are problems when operating the dishwasher
The dishwasher will not start or stops during operation. All push buttons are inoperative except for the On/Off push button. Press the
On/Off push button to switch the dishwasher off and carry out the following suggested corrective actions.
Malfunction
Possible cause
Solutions
The water tap is blocked or furred with
limescale.
Clean the water tap.
The machine does not fill with
water.
The water tap is turned off.
Turn the water tap on.
The filter (where present) in the threaded hose
fitting at the water inlet valve is blocked.
Clean the filter in the threaded hose
fitting.
The water inlet hose has not been correctly laid
or it is bent or squashed.
Check the water inlet hose connection.
The dishwasher will not drain.
The siphon is blocked.
Clean out the siphon.
The water drain hose has not been correctly laid Check the water drain hose connection.
or it is bent or squashed.
The dishwasher door has not been properly
closed.
Close the door.
The programme does not start
The main plug is not plugged in.
Insert the mains plug.
Replace the fuse.
The fuse has blown in the household fuse box.
If dishes are to be washed immediately,
cancel the delay start.
For dishwasher models with delay start
option:
Delay start has been selected.
There is a whistling noise during
washing
The whistling is not a cause for concern.
Use a different brand of detergent.
Once the checks have been carried out, press the On/Off push button, the programme will continue from the point in which it was
interrupted. If the malfunction reappears contact your local Service Force Centre.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
...the wash results are not satisfactory
The dishes are not clean
G The wrong washing programme has been selected.
G The dishes were arranged in such a way as to stop water reaching all parts of the surface. The baskets must not be overloaded.
G The spray arms do not rotate freely due to wrong arrangement of the load.
G The filters in the base of the washing compartment are dirty or incorrectly positioned.
G Too little or no detergent has been used.
G Where there are limescales deposits on the dishes; the salt container is empty or the wrong level of the water softener has been
selected.
G The drain hose connection is not correct.
G The salt container cap is not properly closed.
The dishes are wet and dull
G Rinse aid was not used.
G The rinse aid dispenser is empty.
There are streaks, milky spots or a bluish coating on glasses and dishes
G Decrease rinse aid dosing.
Water drops have dried onto glasses and dishes
G Increase rinse aid dosing.
G The detergent may be the cause. Contact the detergent manufacturer’s consumer care line.
If after all these checks, the problem persists, contact your
local Service Force Centre, quoting the model (Mod.), product
number (PNC) and serial number (S.N.).
This information can be found on the rating plate located on
the right hand side of the dishwasher door (see picture).
So that you always have these numbers at hand, we
recommend you to make a note of them here:
Mod. : . . . . . . . . . . . . . . . . . .
PNC : . . . . . . . . . . . . . . . . . .
S.N. :. . . . . . . . . . . . . . . . . . .
RA08
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation instructions
Any electrical and/or plumbing work required to install
this appliance should be carried out by a qualified
electrician and/or plumber or competent person.
Water outlet hose connection
The end of the drain hose can be connected in the following
ways:
Remove all packaging before positioning the machine.
1. To the sink outlet spigot, securing it to the underside of the
work surface. This will prevent waste water from the sink
running into the machine.
If possible, position the machine next to a water tap and a
drain.
2. Hooked over the edge of the sink using the special curved
plastic guide provided (if provided with the machine).
Water supply connections
This dishwasher may be fed with either hot (max. 60°) or cold
water (See "Technical specifications" - Instruction book part 2).
Nevertheless we advise you a cold water supply.
A hot water supply is not always efficient with very soiled
crockery as it shortens the washing programmes a lot.
3. To a stand pipe provided with vent-hole, minimum internal
diameter 4 cm.
The waste connection must be at a height of between 30 cm
(minimum) and 100 cm (maximum) from the bottom of the
dishwasher.
The drain hose can face either to the right or left of the
dishwasher
The dishwasher must not be connected to open hot water
appliances or instantaneous water heaters.
Ensure the hose is not bent or squashed as this could prevent
or slow down the discharge of water.
The water pressure must be within the limits given in the
technical specifications. Your local Water Authority will advise
you on the average mains pressure in your area.
The sink plug must not be in place when the machine is
draining as this could cause the water to siphon back into the
machine.
The water inlet hose must not be kinked, crushed, or entangled
when it is being connected up.
If you use a drain hose extension it must be no longer than 2
metres and its internal diameter must be no smaller than the
diameter of the hose provided.
The dishwasher features fill and drain hoses which can be
turned either to the left or the right to suit the installation.
Likewise the internal diameter of the couplings used for
connections to the waste outlet must be no smaller than the
diameter of the hose provided.
The dishwasher is fitted with safety devices that prevent the
wash water returning into the drinking water system and
comply with the applicable plumbing regulations.
Do not use, for connection, old hoses which have been
used in another appliance.
If the machine is connected to new pipes or pipes which have
not been used for a long time, you should run the water for a
few minutes before connecting the inlet hose.
CS18
Attention!
Our appliances are supplied with a security device to protect
against the return of dirty water back into the machine.
If the spigot of your sink has a "no return valve" incorporated
this can prevent the correct draining of your dishwasher.
We advise you therefore to remove it.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
This appliance must be earthed.
The manufacturer declines any responsibility should this
safety measure not be observed.
The appliance should not be connected to the electrical
supply by means of an extension cable.
If the plug that is fitted to your appliance is not suitable for the
socket, it must be cut off and the appropriate plug fitted.
Important
The wires on the mains lead are coloured in accordance with
the following code:
Green and Yellow - Earth
Blue
- Neutral
- Live
Brown
If you fit your own plug, the colours of the wires in the mains
lead of your appliance may not correspond with the markings
identifying the terminals in your plug.
Proceed as follows:
1. Connect the Green and Yellow (earth) wire to the terminal
in the plug which is marked with the letter "E" or the earth
symbol
or coloured green and yellow.
2. Connect the Blue (neutral) wire to the terminal in the plug
which is marked with the letter "N" or coloured black.
3. Connect the Brown (live) wire to the terminal in the plug
which is marked with the letter "L" or coloured red.
E
L
N
CE04
The plug moulded onto the lead incorporates a 13amp BSI362
fuse. Only ASTA or BSI fuses should be used.
The plug must not be used if the fuse cover/carrier is lost. The
cover/carrier is indicated by the coloured insert at the base of
the plug.
A replacement cover/carrier must be obtained from your local
Service Force Centre.
To isolate the dishwasher from mains, remove the mains plug.
Important!
The plug must still be accessible after the appliance
has been installed.
In case that the electrical cable has to be replaced,
please contact your local Service Force Centre.
This appliance complies with the following E.E.C. Directives:
- 73/23 or 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 or 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
152971 08/0
Subject to change without notice
0 01/03
Download from Www.Somanuals.com. All Manuals Search And Download.
|