文
中
Owner’s Manual
Bedienungsanleitung
Mode d’emploi
EN
DE
FR
ES
IT
語
Manual de instrucciones
Manuale di istruzioni
Руководство пользователя
日本
取扱説明書
RU
ZH
JA
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC INFORMATION (U.S.A.)
all installations. If this product is found to be the source of
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements. Modifi-
cations not expressly approved by Yamaha may void your
authority, granted by the FCC, to use the product.
interference, which can be determined by turning the unit
“OFF” and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to co-axial type cable.
2. IMPORTANT: When connecting this product to accessories
and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could
void your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15 for
Class “B” digital devices. Compliance with these require-
ments provides a reasonable level of assurance that your
use of this product in a residential environment will not result
in harmful interference with other electronic devices. This
equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the opera-
tion of other electronic devices. Compliance with FCC regu-
lations does not guarantee that interference will not occur in
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to distrib-
ute this type of product. If you can not locate the appropriate
retailer, please contact Yamaha Corporation of America,
Electronic Service Division, 6600 Orangethorpe Ave, Buena
Park, CA90620
The above statements apply ONLY to those products distrib-
uted by Yamaha Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
(class B)
IMPORTANT NOTICE FOR THE UNITED KINGDOM
COMPLIANCE INFORMATION STATEMENT
Connecting the Plug and Cord
(DECLARATION OF CONFORMITY PROCEDURE)
WARNING: THIS APPARATUS MUST BE EARTHED IMPOR-
TANT. The wires in this mains lead are coloured in accor-
dance with the following code:
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park,
Calif. 90620
Telephone : 714-522-9011
Type of Equipment : I/O Expander
Model Name : EXi8/EXo8
GREEN-AND-YELLOW
BLUE
BROWN
:
:
:
EARTH
NEUTRAL
LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including
interference that may cause undesired operation.
The wire which is coloured GREEN-and-YELLOW must be
connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol
or colored GREEN or
See user manual instructions if interference to radio reception
is suspected.
GREEN-and-YELLOW.
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured BLACK.
* This applies only to products distributed by
(FCC DoC)
The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
YAMAHA CORPORATION OF AMERICA.
(3 wires)
이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서
사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습
니다.
(class b korea)
EXi8/EXo8 Owner’s Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from
electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited
to, the following:
Power supply/Power cord
Water warning
• Do not place the power cord near heat sources such as heaters or radiators,
and do not excessively bend or otherwise damage the cord, place heavy
objects on it, or place it in a position where anyone could walk on, trip over,
or roll anything over it.
• Do not expose the device to rain, use it near water or in damp or wet
conditions, or place on it any containers (such as vases, bottles or glasses)
containing liquids which might spill into any openings. If any liquid such
as water seeps into the device, turn off the power immediately and unplug
the power cord from the AC outlet. Then have the device inspected by
qualified Yamaha service personnel.
• Only use the voltage specified as correct for the device. The required
voltage is printed on the name plate of the device.
• Never insert or remove an electric plug with wet hands.
• Use only the supplied power cord/plug.
If you intend to use the device in an area other than in the one you
purchased, the included power cord may not be compatible. Please check
with your Yamaha dealer.
Fire warning
• Do not put burning items, such as candles, on the unit. A burning item may
fall over and cause a fire.
• Check the electric plug periodically and remove any dirt or dust which may
have accumulated on it.
• Be sure to connect to an appropriate outlet with a protective grounding
connection. Improper grounding can result in electrical shock.
If you notice any abnormality
• When one of the following problems occurs, immediately turn off the power
switch and disconnect the electric plug from the outlet. Then have the
device inspected by Yamaha service personnel.
Do not open
• This device contains no user-serviceable parts. Do not open the device or
attempt to disassemble the internal parts or modify them in any way. If it
should appear to be malfunctioning, discontinue use immediately and have
it inspected by qualified Yamaha service personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the instrument.
- There is a sudden loss of sound during use of the device.
• If this device should be dropped or damaged, immediately turn off the
power switch, disconnect the electric plug from the outlet, and have the
device inspected by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or
damage to the device or other property. These precautions include, but are not limited to, the following:
Power supply/Power cord
• When removing the electric plug from the device or an outlet, always hold
the plug itself and not the cord. Pulling by the cord can damage it.
• Do not place the device in a location where it may come into contact with
corrosive gases or salt air. Doing so may result in malfunction.
• Keep device away from the reach of children.
• Before moving the device, remove all connected cables.
• Remove the electric plug from the outlet when the device is not to be used
for extended periods of time, or during electrical storms.
• When setting up the device, make sure that the AC outlet you are using is
easily accessible. If some trouble or malfunction occurs, immediately turn
off the power switch and disconnect the plug from the outlet. Even when the
power switch is turned off, electricity is still flowing to the product at the
minimum level. When you are not using the product for a long time, make
sure to unplug the power cord from the wall AC outlet.
Location
• Do not place the device in an unstable position where it might accidentally
fall over.
• Do not block the vents. This device has ventilation holes at the front and
sides to prevent the internal temperature from becoming too high. In
particular, do not place the device on its side or upside down. Inadequate
ventilation can result in overheating, possibly causing damage to the
device(s), or even fire.
• If the device is mounted in an EIA standard rack, carefully read the section
result in overheating, possibly causing damage to the device(s),
malfunction, or even fire.
PA_en_1 1/2
Download from Www.Somanuals.com. All Manuals Search And Download.
EXi8/EXo8 Owner’s Manual
4
Connections
Handling caution
• Before connecting the device to other devices, turn off the power for all
devices. Before turning the power on or off for all devices, set all volume
levels to minimum.
• Do not insert your fingers or hands in any gaps or openings on the device
(vents).
• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into
any gaps or openings on the device (vents). If this happens, turn off the
power immediately and unplug the power cord from the AC outlet. Then
have the device inspected by qualified Yamaha service personnel.
Maintenance
• Remove the power plug from the AC outlet when cleaning the device.
• Do not rest your weight on the device or place heavy objects on it, and
avoid use excessive force on the buttons, switches or connectors.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.
Always turn the power off when the device is not in use.
NOTICE
To avoid the possibility of malfunction/damage to the product, damage to data, or damage to other property, follow the notices
below.
Handling and Maintenance
• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the
device, TV, or radio may generate noise.
• Do not expose the device to excessive dust or vibration, or extreme cold or heat (such as in direct sunlight, near a heater, or in
a car during the day), in order to prevent the possibility of panel disfiguration, unstable operation, or damage to the internal
components.
• Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel.
• When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impreg-
nated wiping cloths.
• Condensation can occur in the device due to rapid, drastic changes in ambient temperature—when the device is moved from
one location to another, or air conditioning is turned on or off, for example. Using the device while condensation is present can
cause damage. If there is reason to believe that condensation might have occurred, leave the device for several hours without
turning on the power until the condensation has completely dried out.
• When turning on the AC power in your audio system, always turn on the power amplifier LAST, to avoid speaker damage.
When turning the power off, the power amplifier should be turned off FIRST for the same reason.
Information
About this manual
• The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those
on your device.
• The company names and product names in this manual are the trademarks or registered trademarks of their respective com-
panies.
European Models
Inrush Current based on EN 55103-1:2009
1A (on initial switch-on)
1A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4
PA_en_1 2/2
EXi8/EXo8 Owner’s Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Getting Started
Thank you for purchasing the Yamaha Input
Expander EXi8/Output Expander EXo8. This man-
ual will help you take full advantage of the superior
functionality offered by the EXi8/EXo8. After you
have read the manual, keep it in a safe place for ref-
erence when needed.
Features
Support for the newly-developed “YDIF” digital
audio transmission format
“YDIF” is a digital audio transmission format that uses an
Ethernet cable to send and receive up to 16 channels of audio
and word clock. Up to eight YDIF devices (maximum of seven
for the EXi8 and/or EXo8) can be connected to expand the
number of input/output channels available for one system.
Enormous installation flexibility with compact 1U
chassis
The EXi8 is an input expansion unit and the EXo8 is an output
expansion unit. The expansion unit can be installed to locations
where only either input or output is required.
Input (EXi8) / Output (EXo8)
Characteristics ........................................... 91
Parameter settings of EXi8/EXo8
To make the EXi8/EXo8 parameter settings, use the system’s
dedicated application software (MTX Editor: available for Win-
dows OS only). The dedicated application software makes it
easy to design a system and make (or adjust) its settings, result-
ing in the creation of an overall system design. The dedicated
application software and manuals can be downloaded from the
following web site.
NOTE
In order to view the downloaded manuals, Adobe Reader must
be installed in your computer. If you don’t have Adobe Reader,
please access the Adobe Corporation’s website at the following
URL, and download Adobe Reader (free of charge).
http://www.adobe.com/
Firmware Updates
To update the firmware of the unit, you must use the system’s
dedicated application software. For details on firmware updates,
refer to the following web site.
Included items (please check)
• EXi8/EXo8 Owner’s Manual (this document)
• Power cable
• Euroblock plugs (3-pin, with tab, 5.08mm pitch) (8)
• Cable ties (8)
EXi8/EXo8 Owner’s Manual
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Connectors
Front Panel
EXi8
q w
r
r
t
t
y u
i
i
EXo8
e
y u
q [INPUT PEAK] indicators 1–8 (EXi8)
u [YDIF] indicator
These indicators will light red when the input level of the
corresponding INPUT channel is -3 dBFS or higher.
This indicator will light green if the rear panel [YDIF IN]
OUT] connector of another device.
w [INPUT SIGNAL] indicators 1–8 (EXi8)
These indicators will light green when the input level of the
corresponding INPUT channel is -40 dBFS or higher.
When a problem or abnormality occurs in the unit, the indi-
cator that corresponds to the appropriate alert number will
flash in green together with the flashing front panel
[ALERT] indicator.
i
Power switch
This is the power switch. The power is on if the switch is in
position. The power is off if the switch is in the
position.
the
NOTE
• Do not cycle the power switch in rapid succession. Wait at
least 6 seconds before turning the power switch on after it
has been turned off. Failing to observe this precaution
may cause malfunctions.
e [OUTPUT SIGNAL] indicators 1–8 (EXo8)
These indicators will light green when the output level of the
corresponding OUTPUT channel is -40 dBFS or higher.
When a problem or abnormality occurs in the unit, the indi-
cator that corresponds to the appropriate alert number will
flash in green together with the flashing front panel
[ALERT] indicator.
• Even when the power switch is turned off, a small amount
of current is flowing through the unit. If you plan not to use
the unit for a long period of time, remove the power cable
from the AC outlet.
r [ALERT] indicator
When a problem or abnormality occurs in the unit, this indi-
cator will flash in red and at the same time the [INPUT SIG-
NAL] or [OUTPUT SIGNAL] indicator that corresponds to
the alert number will flash in green. For explanations of the
Alert number
Example: When a problem related to alert number “3” occurs
t [POWER] indicator
This indicator will light when this device is powered-on.
y [NETWORK] indicator
This indicator will light green if a link is established with an
external device via the rear panel NETWORK connector
(page 9). It will flash while data is being sent or received.
EXi8/EXo8 Owner’s Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Connectors
Rear Panel
i
q
w
e
r
t
y
u
* Illustration shows EXi8.
NOTE
r DIP switches
The EXi8/EXo8 has some connectors that are shaped identically
These switches enable you to specify the settings related to
the startup operation of the EXi8/EXo8.
but have a completely different function (e.g., NETWORK connec-
tor, [YDIF] connector). Make the appropriate connections as
instructed by the explanation for each connector. Otherwise, you
risk damaging your equipment.
NOTE
Set the DIP switches while the power to the unit is turned
OFF. Otherwise, the setting will not be effective.
q Ground screw
Refer to the following for details.
The supplied power cord has a three-prong plug that will
ground the device when plugged into an appropriately
grounded three-prong type AC mains outlet. In some cases,
you may be able to reduce hum or interference by also con-
necting this screw to ground.
Switch
Status
Represent a status with switch toggled up.
Represent a status with switch toggled
down.
w AC IN connector
Use the included power cord to supply power to this connec-
tor. First, connect the power cord to this device, and then
insert the power cord plug into the AC outlet.
Switches 1–2 (UNIT ID)
These switches specify the upper digit and the above-
mentioned [UNIT ID] rotary switch specifies the lower
digit, together allowing you to specify one of 63 different
UNIT ID numbers in a range from 01 to 3F.
e [UNIT ID] rotary switch
This switch specifies the ID by which EXi8/EXo8 units are
individually distinguished in the MTX system network. You
must specify the ID avoiding duplicates among the MTX
series, XMV series and the EXi8/EXo8 within the same net-
work.
DIP switches 1 and 2 described in r specify the upper digit,
and this rotary switch specifies the lower digit, together
allowing you to set the UNIT ID to one of 63 possibilities in
the range of 01 to 3F.
Switch position
Option
Functions
The [UNIT ID] rotary switch
will have a setting range of
01 through 0F.
UNIT ID is
“0x”
The [UNIT ID] rotary switch
will have a setting range of
10 through 1F.
UNIT ID is
“1x”
The [UNIT ID] rotary switch
will have a setting range of
20 through 2F.
UNIT ID is
“2x”
NOTE
The [UNIT ID] rotary switch
will have a setting range of
30 through 3F.
• Do not use a UNIT ID of “00” (DIP switches 1 and 2
upward and the rotary switch at 0).
UNIT ID is
“3x”
• You’ll need to restart the device after changing the setting
of the [UNIT ID] rotary switch.
NOTE
Do not use a UNIT ID of “00” (DIP switches 1 and 2
upward and the rotary switch at 0).
Switch 3
This switch is for future expansion. Set this to its upward
position.
Switches 4–5 (REMOTE)
Settings of these switches are not necessary. Set these to
their upward position.
Switch position
Option
Function
Enables remote control with
the supported devices.
NATIVE
EXi8/EXo8 Owner’s Manual
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Connectors
Switch 6 (IP SETTING)
u [INPUT] connectors (EXi8)
[OUTPUT] connectors (EXo8)
This switch specifies how the EXi8/EXo8’s IP address
will be specified.
These are balanced input/output connectors for analog audio
input and output. Connect line level devices or microphones
to the [INPUT] connectors, and line level devices to the
[OUTPUT] connectors. The [INPUT] connectors provide
head amps, and can also provide +48V phantom power. The
system’s dedicated application software is used to specify
the gain of the internal head amps and to turn the phantom
power on/off.
Switch position
Option
Functions
The IP address will be
specified according to the
UNIT ID, and will be
UNIT ID
192.168.0.(UNIT ID).
The IP address will be
determined by the settings
of the system’s application
software. (See the user’s
manual of the correspond-
ing application software.)
Use the included Euroblock plugs to make connections (see
PC
NOTE
Adjusting the internal head amp gain between +17 dB and
+18 dB will internally turn PAD on/off. Noise may occur if
there is an impedance difference between the Hot and Cold
of a device connected to the [INPUT] connectors while
phantom power is being used.
NOTE
Set this to the “UNIT ID” position the first time you con-
nect this device to a computer after purchase. After
specifying the IP address from the system’s dedicated
application software, change this switch to the “PC” posi-
tion.
i Cooling vent
The EXi8/EXo8 contains a cooling fan. The cooling air is
exhausted here, so please be careful not to block this vent.
Switches 7–8 (START UP MODE)
These specify whether the EXi8/EXo8 will be initialized
when it is powered-on.
Switch position
Option
Functions
This is the normal operating
mode. When you power-on
the EXi8/EXo8, it will start
up in the same state in
which it was when the
RESUME
Cooling vent
power was turned off.
Initializes the EXi8/EXo8,
INITIALIZE returning it to the factory-set
t NETWORK connector
This is an Ethernet connector that supports AutoMDI/MDI-
X. It enables communication via a network switch with an
MTX network or external controller. Use a CAT5e or better
Ethernet STP cable (shielded twisted pair cable).
y [YDIF] connectors
These connectors are used to make a ring connection with
the devices that comprise the system, allowing digital audio
signals to be transmitted and received. Use CAT5e or better
Ethernet STP cables (shielded twisted pair cables) that have
all eight pins connected in a straight connection. The maxi-
mum cable length between devices is 30 meters, and you can
connect up to total seven EXi8 and EXo8 devices. For
details, refer to the user’s manual of the corresponding appli-
cation software.
EXi8/EXo8 Owner’s Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
1. Loosen the terminal screws.
Precautions for rackmounting
This device is guaranteed to operate at an ambient temperature
of 0 to 40 °C. If this device is mounted in an EIA rack together
with other devices, heat from the various devices may cause the
temperature inside the rack to rise, rendering this device unable
to perform to its full potential. To ensure that heat does not
accumulate inside this device, please ensure that the following
conditions are met when rack-mounting it.
Loosen
Slotted screwdriver
Terminal screw
Euroblock plug
Tab
• If you plan to mount this device together with devices that
tend to generate heat, such as power amps, allow 1U or more
of vacant space between this device and other devices. (How-
ever, you do not need larger than 1U space with the MTX
series or XMV series.) Also attach ventilation panels in this
space or leave them open to ensure sufficient ventilation.
NOTE
• Leave the back of the rack open, and allow at least 10 cm of
space between the rack and the wall or ceiling to ensure suf-
ficient ventilation. If the back of the rack cannot be left open,
provide forced air cooling for the rack, for example by
installing a commercially available fan kit. If you install a
fan kit, leaving the back of the rack closed may provide more
effective cooling. For details, refer to the owner’s manual
provided with the rack or fan kit.
Use a slotted screwdriver with a blade width of 3 mm or
less.
3 mm or less
2. Insert cables.
+
–
G
Euroblock plug connection
Use the included Euroblock plugs when making connections to
the [INPUT]/[OUTPUT] connectors.
Cable preparation
3. Securely tighten the terminal screws.
Pull the cables (not too strongly) to confirm that they are
securely connected.
approx. 7 mm
4. Use the included cable ties to fasten the cable
to the tab.
approx. 20 mm
• Use stranded wire for Euroblock connections, and strip
the wire as shown in the illustration. With a Euroblock
connection, the stranded wire may be prone to break-
age because of metal fatigue due to the weight of the
cable or due to vibration. Cables connected to the
[INPUT]/[OUTPUT] connectors should be fastened to
the tab of the Euroblock plug (3-pin) using the included
cable ties (see illustration at right). When rack-mount-
ing the device, use a lacing bar when possible to bun-
dle and secure the cable.
NOTE
NOTE
Do not tin (plate with solder) the stranded wire.
Trim off the extra portion of the cable tie as necessary.
• If cables will be frequently connected and discon-
nected, as in the case of a portable system, we recom-
mend that you use ferrules with insulation sleeves. Use
a ferrule whose conductor portion has an external
diameter of 1.6 mm or less and a length of approxi-
mately 7 mm such as the AI 0,5 - 6 WH made by the
Phoenix Contact corporation.
approx. 7 mm
1.6 mm or less
EXi8/EXo8 Owner’s Manual
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
5. Plug the Euroblock plug into the [INPUT] con-
nector of the EXi8 or the [OUTPUT] connector
of the EXo8.
Initializing the EXi8/EXo8
Here’s how to initialize the EXi8/EXo8’s internal memory,
restoring it to the factory settings.
1. Power-off the EXi8/EXo8.
2. Set the rear panel DIP switches 7 and 8 to the
“INITIALIZE” position.
3. Power-on the EXi8/EXo8.
Initialization will start.
The status of execution is shown by the [ALERT], [NET-
WORK], and [YDIF] indicators on the front panel.
NOTE
• During initialization:
When connecting unbalanced cables to the [INPUT] con-
nector, use a jumper wire to connect the “-” and “G” of the
Euroblock.
The [NETWORK] indicator and the [YDIF] indicator
will flash rapidly.
+
–
G
• Initialization completed:
The [NETWORK] indicator and the [YDIF] indicator
will flash slowly.
• Initialization failed:
The [ALERT] indicator will flash.
CAUTION
Do not turn off the power to the EXi8/EXo8 during ini-
tialization. Otherwise, a malfunction may occur
NOTE
If initialization failed, contact Yamaha representatives /
authorized distributors to have the device inspected. A list of
Yamaha representatives / authorized distributors appears
near the end of this manual.
4. When initialization is completed, power-off the
EXi8/EXo8 once again.
5. Set the rear panel DIP switches 7 and 8 to the
“RESUME” position.
6. Power-on the EXi8/EXo8 again.
The EXi8/EXo8 will start up in its factory-set state.
EXi8/EXo8 Owner’s Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
An FAQ (frequently asked questions) list is at the Yamaha Pro Audio web site (http://www.yamahaproaudio.com/).
Symptom
Possible cause, and action
Connect the power cord properly.
The device does not turn on, or
the panel LEDs do not light up.
Make sure that the power switch is turned on.
If the power still does not turn on, contact your Yamaha dealer.
Is the NETWORK connector on the EXi8/EXo8 properly connected to your computer?
Cannot exchange data between
the EXi8/EXo8 and system’s dedi- Have you specified the correct UNIT ID using the [UNIT ID] rotary switch and DIP switches 1 and 2
cated application software.
on the rear panel? Could the UNIT ID be conflicting with another device?
(EXi8/EXo8 is not shown in the
dedicated application software)
Set the rear panel DIP switch 6 (IP SETTING) to “UNIT ID” so that the IP address will be automati-
cally assigned according to the UNIT ID.
Connect the cable properly.
No audio input is present.
([INPUT SIGNAL] indicator does
not light)
Make sure that a signal from an external device is being input.
Set the gain of the internal head amplifier or external head amplifier to an appropriate level.
Could the output level be lowered?
In the system’s dedicated application software, could the channel’s ON button be turned off?
Is the signal routing specified correctly?
No audio is output.
([OUTPUT SIGNAL] indicator
does not light)
Have settings such as patch, gain or level in the system’s dedicated application software been made
correctly?
Did you use an appropriate cable to make proper YDIF connections between the EXi8/EXo8 and
other devices in the system? Also, is the power to the YDIF-connected devices turned on?
[YDIF] indicator does not light
An error has occurred. The [INPUT SIGNAL] indicator or the [OUTPUT SIGNAL] indicator that cor-
The [ALERT] indicator is flashing responds to the alert number flashes; refer to the “Alert list” on page 13 to determine the problem
and take appropriate action.
EXi8/EXo8 Owner’s Manual
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Alert list
Flashing [SIGNAL]
indicator
(alert number)
Meaning
Response
Turn the power off, then turn on after waiting at least 6 seconds. If this
The device has not started up correctly. does not solve the problem, please initialize the memory. Should this
also fails, contact your Yamaha dealer.
1
The current preset saved in internal
memory has been lost.
Recall the preset. If this does not solve the problem, contact your
2
3
4
Yamaha dealer.
The word clock master has become
unlocked.
Make sure that the word clock signal is being input correctly.
There is a problem with the connection Make sure that YDIF cables are properly connected.
of the [YDIF IN] connector.
Use cables that meet the required specifications.
Duplicate IP addresses.
Change the IP addresses or UNIT ID so that there are no duplicates.
Please check rear panel DIP switch 6 (IP SETTING). If DIP switch 6 is
set to “PC,” use the system’s dedicated application software or the
DHCP server to specify the device IP address.
IP address was not set within 60 sec-
onds of startup.
5
6
Too many devices are connected to the
network.
Reduce the number of devices connected to the network.
The UNIT ID is set to “00.”
Set the UNIT ID to something other than “00.”
Devices with identical UNIT IDs were
found connected within the same net-
work.
Change the UNIT ID so that there are no duplicates.
EXi8/EXo8 Owner’s Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Specifications
Product specifications
Dimensions (W x H x D)
Weight
480(W) x 44(H) x 351(D)mm, 1U
4.3 kg
Japan: 100V 50/60Hz
Power supply voltage
US/Canada: 110V–240V 50/60Hz
Others: 100V–240V 50/60Hz
Power consumption
25 W max.
Heat dissipation (per hour)
Operating temperature range
Storage temperature range
NC value
21.5 kcal max.
0 °C–40 °C
-20 °C–60 °C
24 (1m from the front panel)
Maximum number of simulta-
neously usable devices
A total of seven EXi8 and EXo8 devices. (However in a system, a total of up to 20 devices, including
devices such as the MTX series and XMV series, can be used.)
Power cord length
Included items
2.5m
Power cord, Euroblock plugs (3-pin, tabbed) x 8, cable ties x 8, Owner’s manual
Electrical specifications
Sampling frequency
Signal delay
48kHz/44.1kHz
Less than 2.5ms
Frequency response
Total harmonic distortion
Dynamic range
20Hz to 20kHz, -1.5dB min, 0dB typ., +0.5dB max.
Less than 0.05% (+4dBu, Gain:-6dB); less than 0.1% (+4dBu, Gain:+66dB)
107dB (Gain:-6dB)
Equivalent input noise (EIN)
-126dBu (Gain: +66dB)
Crosstalk / Channel separation -100dB (@1kHz)
Maximum cable length
[YDIF] connector: 30 meters (Cable length between devices)
INPUT PEAK (EXi8): RED -3dBFS
Indicators
INPUT SIGNAL (EXi8): GREEN -40dBFS
OUTPUT SIGNAL (EXo8): GREEN -40dBFS
Phantom power (EXi8)
+48V (per channel; individually settable)
Connector specifications
Format
NETWORK connector: 100Base-TX
[YDIF] connector: CAT5e or better Ethernet STP cable (Straight connected. All 8 pins must be connected.)
NETWORK connector: CAT5e or better Ethernet STP cable
Cable specifications
EXi8/EXo8 Owner’s Manual
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Input (EXi8) / Output (EXo8) Characteristics
ANALOG INPUT CHARACTERISTICS (EXi8)
Input Level
Input
Terminals
Actual Load
Impedance
For Use With
Nominal
GAIN
Connector
Nominal
Max. before clip
-42dBu (6.16mV)
+30dBu (24.5V)
+66dB
-6dB
-62dBu (0.616mV)
+10dBu (2.45V)
50–600ΩMics
& 600Ω Lines
Euroblock (Balanced)
(5.08mm pitch)
INPUT 1–8
10kΩ
• In these specifications, 0dBu = 0.775 Vrms.
• All input AD converters are 24bit linear, 128times oversampling.
• +48V DC (phantom power) is supplied to INPUT Euroblock connectors via each individual software controlled switch.
ANALOG OUTPUT CHARACTERISTICS (EXo8)
Output Level
ActualSource For Use With
Output Terminals
Connector
Impedance
Nominal
Nominal
Max. before clip
Euroblock (Balanced)
(5.08mm pitch)
OUTPUT 1–8
75Ω
10kΩ Lines
+4dBu (1.23 V)
+24dBu (12.3V)
• In these specifications, 0dBu = 0.775 Vrms.
• All output DA converters are 24bit, 128times oversampling. (Fs=48kHz)
* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or
modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in
every locale, please check with your Yamaha dealer.
* Die technischen Daten und Beschreibungen in dieser Bedienungsanleitung dienen nur der Information. Yamaha Corp. behält sich das
Recht vor, Produkte oder deren technische Daten jederzeit ohne vorherige Ankündigung zu verändern oder zu modifizieren. Da die tech-
nischen Daten, das Gerät selbst oder Sonderzubehör nicht in jedem Land gleich sind, setzen Sie sich im Zweifel bitte mit Ihrem Yamaha-
Händler in Verbindung.
* Les caractéristiques techniques et les descriptions du mode d’emploi ne sont données que pour information. Yamaha Corp. se réserve le
droit de changer ou modifier les produits et leurs caractéristiques techniques à tout moment sans aucun avis. Du fait que les caractéristi-
ques techniques, les équipements et les options peuvent différer d’un pays à l’autre, adressez-vous au distributeur Yamaha le plus pro-
che.
* Las especificaciones y descripciones de este manual del propietario tienen sólo el propósito de servir como información. Yamaha Corp.
se reserva el derecho a efectuar cambios o modificaciones en los productos o especificaciones en cualquier momento sin previo aviso.
Puesto que las especificaciones, equipos u opciones pueden no ser las mismas en todos los mercados, solicite información a su distri-
buidor Yamaha.
* Le specifiche e le descrizioni presenti in questo manuale sono fornite a fini puramente informativi. Yamaha Corp. si riserva il diritto di
modificare prodotti o specifiche in qualsiasi momento senza preavviso. Dato che le specifiche, le apparecchiature o le opzioni possono
essere diverse da paese a paese, verificarle con il proprio rappresentante Yamaha.
* Технические характеристики и их описания в данном руководстве пользователя предназначены только для общего
сведения. Корпорация Yamaha сохраняет за собой право модифицировать свои изделия и менять их технические
характеристики без предварительного уведомления. Поскольку технические характеристики, оборудование и набор
возможностей могут зависеть от региона, обращайтесь за информацией к местному представителю корпорации Yamaha.
* 本使用说明书中的技术规格及介绍仅供参考。Yamaha公司保留随时更改或修订产品或技术规格的权利,若确有更改,恕不事先通知。技
术规格、设备或选购件在各个地区可能均会有所不同,因此如有问题,请和当地Yamaha经销商确认。
* 仕様および外観は、改良のため予告なく変更することがあります。
EXi8/EXo8 Owner’s Manual
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Information for Users on Collection and Disposal of Old Equipment
This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not
be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your
national legislation and the Directives 2002/96/EC.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human
health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or
the point of sale where you purchased the items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
[Information on Disposal in other Countries outside the European Union]
This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask
for the correct method of disposal.
(weee_eu_en_01)
Verbraucherinformation zur Sammlung und Entsorgung alter Elektrogeräte
Befindet sich dieses Symbol auf den Produkten, der Verpackung und/oder beiliegenden Unterlagen, so sollten benutzte elektrische
Geräte nicht mit dem normalen Haushaltsabfall entsorgt werden.
In Übereinstimmung mit Ihren nationalen Bestimmungen und den Richtlinien 2002/96/EC bringen Sie alte Geräte bitte zur fachgerechten
Entsorgung, Wiederaufbereitung und Wiederverwendung zu den entsprechenden Sammelstellen.
Durch die fachgerechte Entsorgung der Elektrogeräte helfen Sie, wertvolle Ressourcen zu schützen, und verhindern mögliche negative
Auswirkungen auf die menschliche Gesundheit und die Umwelt, die andernfalls durch unsachgerechte Müllentsorgung auftreten könnten.
Für weitere Informationen zum Sammeln und Wiederaufbereiten alter Elektrogeräte kontaktieren Sie bitte Ihre örtliche Stadt- oder
Gemeindeverwaltung, Ihren Abfallentsorgungsdienst oder die Verkaufsstelle der Artikel.
[Information für geschäftliche Anwender in der Europäischen Union]
Wenn Sie Elektrogeräte ausrangieren möchten, kontaktieren Sie bitte Ihren Händler oder Zulieferer für weitere Informationen.
[Entsorgungsinformation für Länder außerhalb der Europäischen Union]
Dieses Symbol gilt nur innerhalb der Europäischen Union. Wenn Sie solche Artikel ausrangieren möchten, kontaktieren Sie bitte Ihre ört-
lichen Behörden oder Ihren Händler und fragen Sie nach der sachgerechten Entsorgungsmethode.
(weee_eu_de_01)
Information concernant la Collecte et le Traitement des déchets d’équipements électriques et électroniques.
Le symbole sur les produits, l'emballage et/ou les documents joints signifie que les produits électriques ou électroniques usagés ne doi-
vent pas être mélangés avec les déchets domestiques habituels.
Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et électroniques, veuillez les
déposer aux points de collecte prévus à cet effet, conformément à la réglementation nationale et aux Directives 2002/96/EC.
En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous contribuerez à la sauvegarde de pré-
cieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui pourraient advenir lors d'un traitement inappro-
prié des déchets.
Pour plus d'informations à propos de la collecte et du recyclage des déchets d’équipements électriques et électroniques, veuillez contac-
ter votre municipalité, votre service de traitement des déchets ou le point de vente où vous avez acheté les produits.
[Pour les professionnels dans l'Union Européenne]
Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques veuillez contacter votre vendeur ou fournis-
seur pour plus d'informations.
[Information sur le traitement dans d'autres pays en dehors de l'Union Européenne]
Ce symbole est seulement valable dans l'Union Européenne. Si vous souhaitez vous débarrasser de déchets d’équipements électriques
et électroniques, veuillez contacter les autorités locales ou votre fournisseur et demander la méthode de traitement appropriée.
(weee_eu_fr_01)
Información para Usuarios sobre Recolección y Disposición de Equipamiento Viejo
Este símbolo en los productos, embalaje, y/o documentación que se acompañe significa que los productos electrónicos y eléctricos usa-
dos no deben ser mezclados con desechos hogareños corrientes.
Para el tratamiento, recuperación y reciclado apropiado de los productos viejos, por favor llévelos a puntos de recolección aplicables, de
acuerdo a su legislación nacional y las directivas 2002/96/EC.
Al disponer de estos productos correctamente, ayudará a ahorrar recursos valiosos y a prevenir cualquier potencial efecto negativo sobre
la salud humana y el medio ambiente, el cual podría surgir de un inapropiado manejo de los desechos.
Para mayor información sobre recolección y reciclado de productos viejos, por favor contacte a su municipio local, su servicio de gestión
de residuos o el punto de venta en el cual usted adquirió los artículos.
[Para usuarios de negocios en la Unión Europea]
Si usted desea deshacerse de equipamiento eléctrico y electrónico, por favor contacte a su vendedor o proveedor para mayor informa-
ción.
[Información sobre la Disposición en otros países fuera de la Unión Europea]
Este símbolo sólo es válido en la Unión Europea. Si desea deshacerse de estos artículos, por favor contacte a sus autoridades locales y
pregunte por el método correcto de disposición.
(weee_eu_es_01)
Informazioni per gli utenti sulla raccolta e lo smaltimento di vecchia attrezzatura
Questo simbolo sui prodotti, sull’imballaggio e/o sui documenti che li accompagnano significa che i prodotti elettrici ed elettronici non
dovrebbero essere mischiati con i rifiuti domestici generici.
Per il trattamento, recupero e riciclaggio appropriati di vecchi prodotti, li porti, prego, ai punti di raccolta appropriati, in accordo con la Sua
legislazione nazionale e le direttive 2002/96/CE.
Smaltendo correttamente questi prodotti, Lei aiuterà a salvare risorse preziose e a prevenire alcuni potenziali effetti negativi sulla salute
umana e l'ambiente, che altrimenti potrebbero sorgere dal trattamento improprio dei rifiuti.
Per ulteriori informazioni sulla raccolta e il riciclaggio di vecchi prodotti, prego contatti la Sua amministrazione comunale locale, il Suo ser-
vizio di smaltimento dei rifiuti o il punto vendita dove Lei ha acquistato gli articoli.
[Per utenti imprenditori dell'Unione europea]
Se Lei desidera disfarsi di attrezzatura elettrica ed elettronica, prego contatti il Suo rivenditore o fornitore per ulteriori informazioni.
[Informazioni sullo smaltimento negli altri Paesi al di fuori dell'Unione europea]
Questo simbolo è valid0 solamente nell'Unione Europea. Se Lei desidera disfarsi di questi articoli, prego contatti le Sue autorità locali o il
rivenditore e richieda la corretta modalità di smaltimento.
(weee_eu_it_01)
EXi8/EXo8 Owner’s Manual
93
Download from Www.Somanuals.com. All Manuals Search And Download.
EXi8/EXo8 Owner’s Manual
94
Download from Www.Somanuals.com. All Manuals Search And Download.
For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou
au distributeur le plus proche de vous figurant dans la liste suivante.
Para detalles sobre productos, contacte su tienda Yamaha más
cercana o el distribuidor autorizado que se lista debajo.
MALTA
Olimpus Music Ltd.
NORTH AMERICA
ASIA
CANADA
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
The Emporium, Level 3, St. Louis Street Msida
MSD06
Tel: 02133-2144
Yamaha Canada Music Ltd.
135 Milner Avenue, Toronto, Ontario,
M1S 3R1, Canada
NETHERLANDS/BELGIUM/
LUXEMBOURG
Yamaha Music Europe Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, Netherlands
Tel: 0347-358 040
Tel: 416-298-1311
Tel: 021-6247-2211
U.S.A.
INDIA
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, CA 90620,
U.S.A.
Yamaha Music India Pvt. Ltd.
Spazedge building, Ground Floor, Tower A, Sector
47, Gurgaon- Sohna Road, Gurgaon, Haryana, India
Tel: 0124-485-3300
FRANCE
Yamaha Music Europe
7 rue Ambroise Croizat, Zone d'activites Pariest,
77183 Croissy-Beaubourg, France
Tel: 01-64-61-4000
Tel: 714-522-9011
INDONESIA
CENTRAL & SOUTH AMERICA
MEXICO
Yamaha de México, S.A. de C.V.
Av. Insurgentes Sur 1647 Piso 9, Col. San José
Insurgentes, Delegación Benito Juárez, México,
D.F., C.P. 03900
PT. Yamaha Musik Indonesia (Distributor)
Yamaha Music Center Bldg. Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 021-520-2577
ITALY
Yamaha Music Europe GmbH, Branch Italy
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
KOREA
Yamaha Music Korea Ltd.
8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
Tel: 02-3467-3300
Tel: 55-5804-0600
SPAIN/PORTUGAL
Yamaha Music Europe GmbH Ibérica, Sucursal
en España
Ctra. de la Coruna km. 17,200, 28231
Las Rozas (Madrid), Spain
Tel: +34-91-639-88-88
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913 - 4º andar, Itaim Bibi,
CEP 04534-013 São Paulo, SP. BRAZIL
Tel: 011-3704-1377
MALAYSIA
Yamaha Music (Malaysia) Sdn., Bhd.
No.8, Jalan Perbandaran, Kelana Jaya, 47301
Petaling Jaya, Selangor, Malaysia
Tel: 03-78030900
ARGENTINA
Yamaha Music Latin America, S.A.,
Sucursal Argentina
Olga Cossettini 1553, Piso 4 Norte,
Madero Este-C1107CEK
Buenos Aires, Argentina
Tel: 011-4119-7000
GREECE
Philippos Nakas S.A. The Music House
147 Skiathou Street, 112-55 Athens, Greece
Tel: 01-228 2160
SINGAPORE
Yamaha Music (Asia) Private Limited
Block 202 Hougang Street 21, #02-00,
Singapore 530202, Singapore
Tel: 65-6747-4374
SWEDEN/FINLAND/ICELAND
Yamaha Music Europe GmbH Germany filial
Scandinavia
J. A. Wettergrensgata 1, Box 30053
S-400 43 Göteborg, Sweden
Tel: +46 31 89 34 00
TAIWAN
VENEZUELA
Yamaha Music Latin America, S.A.,
Sucursal Venezuela
C.C. Manzanares Plaza P4
Ofic. 0401- Manzanares-Baruta
Caracas Venezuela
Yamaha Music & Electronics Taiwan Co.,Ltd.
3F, No.6, Section 2 Nan-Jing East Road, Taipei,
Taiwan R.O.C.
DENMARK
Yamaha Music Europe GmbH, Tyskland – filial
Denmark
Generatorvej 6A, DK-2730 Herlev, Denmark
Tel: 44 92 49 00
Tel: 02-2511-8688
THAILAND
Tel: 58-212-943-1877
Siam Music Yamaha Co., Ltd.
3, 4, 15 and 16th floor, Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: 02-215-2622
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso No.7, Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, República de Panamá
Tel: +507-269-5311
NORWAY
Yamaha Music Europe GmbH Germany -
Norwegian Branch
Grini Næringspark 1, N-1361 Østerås, Norway
Tel: 67 16 78 00
VIETNAM
Yamaha Music Vietnam Company Limited
15th Floor, Nam A Bank Tower, 201-203 Cach
Mang Thang Tam St., Ward 4, Dist.3,
Ho Chi Minh City, Vietnam
RUSSIA
Yamaha Music (Russia) LLC.
Room 37, bld. 7, Kievskaya street, Moscow,
121059, Russia
Tel: +84-8-3818-1122
EUROPE
OTHER ASIAN COUNTRIES
Yamaha Corporation
Sales & Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
THE UNITED KINGDOM/IRELAND
Yamaha Music Europe GmbH (UK)
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, U.K.
Tel: 495 626 5005
OTHER EUROPEAN COUNTRIES
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
Tel: 01908-366700
Tel: +81-53-460-2312
GERMANY
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
AFRICA
Yamaha Music Gulf FZE
Office JAFZA 16-512, P.O.Box 17328,
Jebel Ali - Dubai, UAE
OCEANIA
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH
Branch Switzerland in Zürich
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 044-387-8080
Tel: +971-4-881-5868
Tel: 3-9693-5111
MIDDLE EAST
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation
Sales & Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
TURKEY
AUSTRIA/BULGARIA
Yamaha Music Europe GmbH
Merkezi Almanya Türkiye İstanbul Şubesi
Maslak Meydan Sokak No:5 Spring Giz Plaza
Bağımsız Böl. No:3, 34398 Şişli İstanbul
Tel: +90-212-999-8010
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
CZECH REPUBLIC/HUNGARY/
ROMANIA/SLOVAKIA/SLOVENIA
Yamaha Music Europe GmbH
Branch Austria (Central Eastern Europe Office)
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
Tel: +81-53-460-2312
CYPRUS
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
OTHER COUNTRIES
Yamaha Music Gulf FZE
Office JAFZA 16-512, P.O.Box 17328,
Jebel Ali - Dubai, U.A.E
POLAND/LITHUANIA/LATVIA/ESTONIA
Yamaha Music Europe GmbH
Branch Poland Office
ul. Wrotkowa 14 02-553 Warsaw, Poland
Tel: 022-500-2925
Tel: +971-4-881-5868
PA36
HEAD OFFICE Yamaha Corporation, Audio Products Sales and Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
EXi8/EXo8 Owner’s Manual
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Yamaha Pro Audio global web site
Yamaha Manual Library
C.S.G., PA Development Division
© 2013 Yamaha Corporation
310YJHD-B0
Printed in China
ZG06180
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Whirlpool Ventilation Hood RH2030XJB3 User Manual
Wolf Microwave Oven 30 E SERIES User Manual
Woodstock Dust Collector W1816 User Manual
Woodstock Planer W1694 User Manual
Worksaver Lawn Mower PLR 48, PLR 72, PLR 60, PBX 42 User Manual
Yamaha Musical Instrument CVP 20 User Manual
Zanussi Cooktop GC17 User Manual
Zanussi Dishwasher 531306 User Manual
Zanussi Washer ZWQ 7100 SO User Manual
Zenoah Brush Cutter BK2650DL Hb User Manual