Operating Manual
USER'S INSTRUCTIONS
Model No.: RETRT2812-1
(DC 12V
/AC 24V ~ 60HZ, 12W / NTSC)
REVO AMERICA
700 FREEPORT PARKWAY SUITE 100 COPPELL,
TX 75019 U.S.A. TEL.: 1-866-625-REVO(7386)
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
Contents
•
•
•
•
•
General Features
4
5
6
7
Installing & Adjusting
Dimension & Specification
OSD Control Button
Camera Menu Set Up
1
.
.
.
.
.
.
.
.
.
.
Menu Set Up
8
2
Lens Setting
8
3
Exposure Setting
White Balance Setting
SSDR Setting
9
4
10
11
12
13
14
15
19
20
5
6
Backlight Setting
DNR3 Setting
7
8
Day/Night Setting
Special Setting
Exit Setting
9
10
•
Trouble Shooting
3
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
General Features
•
Ultra High Sensitivity
- The built-in high sensitivity COLOR CCD produces a clear image even in 0Lux(B/W, IR-LED ON)
or lower illumination.
•
600TV Lines
- By adopting a diagonal 2.8mm(1/3") 410,000 (NTSC) pixel, 470,000(PAL) pixel SONY CCD,
the camera produces clear picture quality with a horizontal resolution of 600 TV lines for
color and a horizontal resolution of 700TV lines for BW mode.
•
DNR3
-
The high-performance W-V DSP chip effectively removes low-light gain noise and
ghosting to
provide clear images even in dark environments.
•
Day & Night
- This camera has a function that automatically selects the mode that is appropriate for
daytime or night-time conditions. The COLOR mode operates in daytime conditions to
provide optimum colors, and BW mode operates in night-time conditions to enhance the
definition of the image.
•
SSDR
- For images with high contrast between bright and dark Areas from difficult lighting conditions
such as backlighting, this camera selectively illuminates darker Areas while retaining the same
light level for brighter Areas to even out the overall brightness.
•
Miscellaneous Functions
- HLC(High Light Compensation), SENS-UP, FLIP(H/V-REV), D-ZOOM, SHARPNESS, MOTION
DETECTION and PRIVACY functions are provided.
•
Disk Saving Effects
- Up-most and advanced DNR technology camera picture quality has a disk saving effects due
to
Image sizes are smaller than standard CCTV camera image.
•
Controlled by OSD Menu
- The camera can be controlled by selecting the menu text displayed on the monitor screen.
•
IP66 Approved / Vandal Proof / RoHS Compliance
- To prevent from external strong impact
.
It has a high strength and durable exterior material of die
cast aluminum body It also has designed to prevent from shock, dust and rain resistant. The
.
turret camera has designed to install anywhere even at exterior places.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
INSTALLING & ADJUSTING
1.
Installation
- Place the mounting plate on a flat installation surface
and mount with the provided screws.
- Feed the cable through the center of the mounting plate.
- Place the camera body in the mounting plate socket
and hold.
- Then place the outer plate over the camera body &
mounting plate and tighten side screws to lock the
camera into place.
- Loosen side screws to adjust camera angle as needed,
then tighten the side screws to lock into place.
2.
Focus/Zoom Screw
- To widen the viewing angle turn the Zoom screw
to "W"(Wide) to obtain a closer view turn it to
"T"(Tele)
- Turn the Focus screw to "N"(Near) or "
(Far) until the sharpest Focus is made.
"
∞
5
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
DIMENSION & SPECIFICATION
1. Dimension & Connection
Dimension
Connection
140mm
2.
Specification
Image Pick-Up Device
TV System
1/3” Sony Super HAD CCD
NTSC
Total Pixels
811(H) * 508(V)
768(H) * 494(V)
Scanning Frequency
Scanning System
Synchronization
Resolution
15.734KHz(H) & 59.94Hz(V)
2:1 Interlace
Internal / Line Lock
600TV Lines
Minimum Illumination
S/N Ratio
IR LED OFF: 0.15 Lux, IR LED ON: 0.00002 Lux
More than 52dB
VideoOutput
Electronic Shutter Speed
OSD
CVBS: 1.0Vp-p / 75Ω
NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec)
Available
SSDR
On / O Level adjustable)
BLC / HLC / OFF
BLC
Day & Night
Color / BW / AUTO
Gain Control
Low / High /
White Balance
SENS-UP
ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K)
Auto / O Selectable x2 ~ x512)
Motion Detection
Privacy Masking
DNR3(DigitalNoiseReduction)
Digital Zoom
DIS (Digital ImageStabilization)
Sharpness
On / O
On / O
Programmable Zones)
Programmable Zones)
On / O Level adjustable)
On / O x1 ~ x16)
On /
On / O Level adjustable)
Flip / Mirror
On /
Power Supply
Power Consumption
Lens
DC 12V / AC 24V Dual Voltage
IR LED OFF 200mA(DC), IR LED OFF 70mA(AC) / IR LED ON 670mA(DC), IR LED ON 240mA(AC)
DC Auto Iris Varifocal Lens(2.8mm-12mm)
Operational Temp
.
-10 ~ +50 Deg C
-20 ~ +60 Deg C
.
.
RH95% MAX.
RH95% MAX.
Storage Temp
.
Dimension
Weight
140mm(W) * 111mm(H) * 180mm(D)
1800g
6
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
OSD Control Button
1.
OSD button could be used when it needs to OSD control.
▲
▼
•
Up button: Moves the cursor upwards
or adjust the parameters.
.
Use this button to select an item
Down button: Moves the cursor downwards
item or adjust the parameters.
.
Use this button to select an
Left button: Moves the cursor to the left
.
Use this button to select or
adjust the parameters of the selected item
.
The parameter changes
each time this button is pressed.
•
•
Right button: Moves the cursor to the right
.
Use this button to select or
The parameter changes each
adjust the parameters of the selected item
.
time this button is pressed.
Set button: Executes selections and displays a submenu for an item with
the mark.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
●
Menu Setup
1
.
Press the Function Setup switch.
- Main setup menu is displayed on the monitor screen.
MA N SETUP
1 LENS
DC
2 EXPOSURE
3 WH TE BAL
ATW
OFF
OFF
ON
4 SSDR
5 BACKL GHT
6 DNR3
7 DAY/N GHT
8 SPEC AL
9 EX T
AUTO
SAVE
2
.
Select a desired function using the Function Setup switch.
- Place the cursor over a desired item.
3
4
.
Set up a selected item by using the Function Setup switch.
. To finish the setting, select 'EXIT' and press the Function Setup switch.
NOTE
☞
■
An item with the◄ icon also has sub menus. To select a sub menu, select an item
with the icon and press the Function Setup switch.
An item with the - - - icon is unavailable due to function settings.
■
●
Lens Setting
Using this function, you can control the screen brightness.
1
2
.
When the SETUP menu screen is displayed, select 'LENS' by using
the Function Setup switch so that the arrow indicates 'LENS'.
DC: You can adjust the minimum shutter and maximum value of ESC
shutter mode.
.
MA N SETUP
1 LENS
DC
2 EXPOSURE
3 WH TE BAL
ATW
3
.
THE Lens mode has sub menu items as listed below.
- BRIGHTNESS: Adjusts the video brightness.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
- FOCUS ADJ: To adjust the DC lens focus correctly, you must activate the Focus Settings
mode under each lens menu Activate the Focus Settings mode, adjust the lens focus, and
.
then deactivate the settings mode.
NOTE
☞
■
If color rolling occurs when using a DC lens, set Shutter to Fixed (---).
●
Exposure Setting
MA N SETUP
1 LENS
DC
2 EXPOSURE
3 WH TE BAL
ATW
1
.
When the SETUP menu screen is displayed, select 'EXPOSURE' by using the
Function Setup Switch.
2
.
Select a desired mode using the Function Setup switch.
EXPOSURE SETUP
1 BR GHTNESS
2 SHUTTER
3 AGC
25
H GH
OFF
4 SENS UP
5 RETURN
SHUTTER: You can select either auto or manual shutter.
◆
* --- : Shutter speed is fixed at 1/60sec(1/50sec)
* ESC: Select this to control the shutter speed automatically
.
If ESC is selected, the shutter
speed is automatically controlled depending on the ambient illumination of the subject.
* MANUAL: You can control shutter speed manually.
(NTSC MODEL:1/60~1/120,000, PAL MODEL:1/50~1/120,000)
* A.FLK : Select this when you see picture flicker, this can happen when the frequency of the
local lighting clashes with the camera.
NOTE
☞
■
When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
◆
AGC (AUTO GAIN CONTROL): The higher the gain level, the brighter the screen
but the higher the noise.
* OFF: Deactivates the AGC function.
* LOW:Allows automatic gain control from 5.3dB to 32dB.
* HIGH:Allows automatic gain control from 5.3dB to 37dB.
◆
SENS-UP: When it is night or dark, the camera automatically detects the light
level and maintains a clear picture if this mode is activated.
* OFF: Deactivates the SENS-UP function.
* AUTO:Activates the SENS-UP function.
◆
RETURN: Select this to save the changes in the EXPOSURE menu and
return to the SETUP menu.
NOTE
☞
■
If you press the Function Setup switch to ‘AUTO’ mode, you can adjust
brightness by
increasing or decreasing the shutter speed (x2 ~ x512)
.
■ Note that the higher the zoom level, the brighter the screen, but the more likely
there will be a ghosting effect.
■ It is normal for Noise, Spots and Whitish symptoms to appear in SENS-UP mode
when the D-ZOOM level is increased.
●
White Balance (White Bal) Setting
Use the White Balance function to adjust the screen color.
1.
When the SETUP menu screen is displayed, select 'White Bal' by using the Function
Setup switch so that the arrow indicates 'White Bal'.
2.
Select a desired mode using the Function Setup switch.
MA N SETUP
1 LENS
DC
2 EXPOSURE
3 WH TE BAL
ATW
10
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
•
•
Select one of the following 5 modes, as appropriate for your
purpose.
ATW: Select this when the color temperature is between 1,700˚K
and 11,000˚K.
OUTDOOR:Select this when the color temperature is between 1,700˚K and 11,000˚K.
(sodium light inclusion)
•
•
INDOOR:Select this when the color temperature is between 4,500˚K and 8,500˚K.
MANUAL: Select this to fine-tune White Balance manually
.
Set White Balance first by using the
ATW or AWC mode After that switch to MANUAL mode, fine-tune the White Balance and then
.
press the Function Setup switch.
•
AWC→SET:To find the optimal luminance level for the current environment, point the
camera towards a sheet of white paper and press the Function Setup switch
changes, readjust it.
.
If the environment
NOTE
☞
■
White Balance may not work properly under the following conditions
select the AWC mode.
when the color temperature of the environment surrounding the subject is out of the
.
In this case
■
control range (e.g clear sky or sunset).
.
when the ambient illumination of the subject is dim.
If the camera is directed towards a fluorescent light or is installed in a place where
■
■
illumination changes dramatically, the White Balance operation may become unstable.
●
SSDR Setting
SSDR illuminates darker spots of an image while retaining the same light level for brighter
spots to even out the overall brightness of images with high contrast between bright and
dark spots.
MA N SETUP
1 LENS
DC
2 EXPOSURE
3 WH TE BAL
ATW
OFF
4 SSDR
1
.
When the SETUP menu screen is displayed, select 'SSDR' by using the switch so
that the arrow indicates 'SSDR'.
Use the switch to change the SSDR level according to the contrast between bright
and dark areas.
2
.
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
●
Backlight Setting
Unlike conventional cameras, W-V chip camera is designed to deliver a distinctive subject
and background at the same time, even when the subject is backlight, by using the features
of the proprietary W-V DSP chip.
1.
When the SETUP menu screen is displayed, select 'BACKLIGHT' by using the Function
Setup switch so that the arrow indicates 'BACKLIGHT'.
MA N SETUP
1 LENS
DC
2 EXPOSURE
3 WH TE BAL
ATW
OFF
OFF
ON
4 SSDR
5 BACKL GHT
6 DNR3
7 DAY/N GHT
8 SPEC AL
9 EX T
AUTO
SAVE
2
.
Select a desired mode using the Function Setup switch.
•
BLC : Enables a user to directly select a desired area from a picture, and to view
the area more clearly.
•
HLC (High Light Compensation) : If the scene contains extremely bright light areas
such as; from car headlights, the light can mask out much of the on-screen detail
- LEVEL :Adjust level of the HLC function.
- LIMIT:Enable to change the operating condition.
- MASK COLOR/TONE: Change the color / transparency of the masking area.
(Black, Red, Blue, Cyan, Magenta)
- TOP/BOTTOM/LEFT/RIGHT: Adjust the area to be enhanced
•
OFF: Not being used
3.
Select a desired mode using the Function Setup switch and press the Function Setup switch.
•
Select 'BLC' to adjust the area to be
enhanced then adjust the level
Select 'HLC' to adjust the area to be
enhanced then adjust the level.
■
.
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
USER’S MANUAL
HLC SETUP
BLC SETUP
LEVEL
T
LOW
38
M DDLE
N GHT ONLY
LEVEL
L M TS
BOTTOM
LEFT
R GHT
109
54
121
MASK COLOR
MASK TONE
TOP
BLACK
1
5
BOTTOM
LEFT
120
5
Press Set to Return
R GHT
172
Press Set to Return
NOTE
☞
■
Because there can be a difference in the effectiveness of HLC according to the amount
of light area in the screen, optimize the installation angle for the best HLC performance.
When dark, the HLC is only activated when a bright light exceeding a specific size in
NIGHT ONLY mode.
The HLC is not activated in day light or when bright light is not present at night in NIGHT
ONLY mode.
■
■
■
BLC Function doesn't work in the B/W mode of the DAY/NIGHT menu.
●
DNR3 Setting
This function reduces the background noise in a low luminance environment.
1.
When the SETUP menu screen is displayed, select 'DNR3' by using the Function
Setup switch so that the arrow indicates 'DNR3'.
MA N SETUP
1 LENS
DC
2 EXPOSURE
3 WH TE BAL
4.SSDR
5 BACKL GHT
6 DNR3
ATW
OFF
OFF
ON
AUTO
7 DAY/N GHT
8 SPEC AL
9 EX T
SAVE
2
•
•
.
Select a desired mode using the Function Setup switch.
OFF: Deactivates DNR3 Noise is not reduced.
ON: Activates DNR3 so that noise is reduced.
.
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
3
.
Set the DNR3 mode to 'ON' and press the Function Setup switch
.
Then you
can adjust the noise reduction level.
NOTE
☞
■
■
You cannot set the DNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is ‘OFF’.
When adjusting the noise reduction level in the DNR3 mode, remember that the higher the
level set, the more the noise level will be reduced, as will the brightness of the image.
●
Day/Night Setting
You can display pictures in color or black and white.
1
.
When the SETUP menu screen is displayed, select 'DAY/NIGHT 'by using the
Function Setup switch so that the arrow indicates 'DAY/NIGHT'.
MA N SETUP
1 LENS
DC
2 EXPOSURE
3 WH TE BAL
4.SSDR
5 BACKL GHT
6 DNR3
ATW
OFF
OFF
ON
AUTO
7 DAY/N GHT
8 SPEC AL
9 EX T
SAVE
2
.
Select a desired mode using the Function Setup Switch according to the picture
display you want.
•
•
COLOR: The picture is always displayed in color.
B/W: The picture is always displayed in black and white.
- BURST MODE: You can turn on or off the burst signal on B/W mode.
B/W MODE SETUP
1 BURST MODE
RETURN
ON
2
14
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
•
AUTO:The mode is switched to 'Color' in a normal environment, but switches to 'B/W' mode
when ambient illumination is low
.
To set up the switching time for AUTO mode, press the
Function Setup switch You can turn on or off the burst signal on B/W mode.
.
- BURST MODE:You can turn on or off the burst signal
on B/W mode.
AUTO SETUP
ON
1 BURST MODE
-DURATION:You can select brightness of illumination
about changing the day/night mode.
2 COLOR→B/W
DURAT ON
DWELL T ME
3 B/W→COLOR
DURAT ON
FAST
3SEC
- DWELLTIME:You can select the duration time about
changing the day/night mode.
FAST
10SEC
DWELL T ME
4 RETURN
→3s, 5s, 7s, 10s, 15s, 20s, 30s, 40, 60s
COLOR→B/W
2.5 lux
B/W→COLOR
5 lux
FAST
SLOW
* The day/night switching point of the
camera can be adjusted.
10 lux
1 lux
NOTE
☞
■
When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as like selecting 'COLOR'
mode and 'AUTO' mode cannot be selected.
●
Special Setting
1
.
When the SETUP menu screen is displayed, select 'SPECIAL' by using the Function Setup
switch so that the arrow indicates 'SPECIAL'.
MA N SETUP
1 LENS
DC
2 EXPOSURE
3 WH TE BAL
4.SSDR
5 BACKL GHT
6 DNR3
ATW
OFF
OFF
ON
AUTO
7 DAY/N GHT
8 SPEC AL
9 EX T
SAVE
15
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
2
.
Select a desired mode using the Function Setup switch.
SPEC AL
1 MAGE ADJ
2 MON TOR
LCD
OFF
3
CAM T TLE
NT
4 SYNC
OFF
5 MOT ON DET
OFF
6 PR VACY
ENGL SH
7 LANGUAGE
9 RETRUN
•
IMAGEADJ.:
1) When the SETUP menu screen is displayed, select 'IMAGE ADJ' by using the
Function Setup switch so that the arrow indicates 'IMAGE ADJ'.
2) Select a desired mode using the Function Setup switch.
MAGE SETUP
1 V REV
2 H
3 D
REV
ZOOM
OFF
OFF
4 D S
OFF
5 FONT COLOR
WH TE
ON
6 SHARPNESS
7 RETURN
* V-REV:You can flip the picture vertically on the screen.
* H-REV:You can flip the picture horizontally on the screen. *
* D-ZOOM: You can use a digital zoom of x1 ~ x16.
* FONT COLOR:You can change the OSD font color (White, Yellow, Green, Red, Blue)
.
* SHARPNESS:As you increase this value, the picture outline becomes stronger and clearer.
Adjust this value appropriately depending on the sharpness of the picture.
* DIS (Digital Image Stabilizer):
This function mitigates any picture movement due to external factors such as wind.
NOTE
☞
■
■
■
As the DIS function uses the digital zoom the camera's resolution will decrease.
DIS doesn’t operate when background illumination is too low.
DIS doesn’t operate when object pattern is monotonic as like sky or white wall.
* RETURN: Select this to save the settings for the IMAGE ADJ menu and to return to the SETUP
menu.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
NOTE
☞
■
■
When the V-REV or H-REV mode is enabled, the text on the screen does not flip.
If you increase the SHARPNESS level too high, the picture may become distorted or noise
may appear.
•
CAM TITLE: If you enter a title, the title will appear on the monitor.
1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the
arrow indicates 'CAM TITLE'.
CAMERA T TLE SETUP
2) Set it to 'ON' by using the Function Setup switch.
A B C D E F G H J K L M
3) Press the Function Setup switch.
N O P Q R S T U V W X Y Z
4) Use the Function Setup switch to move to a
desired letter and select the letter by pressing
a b c d e f g h i j k
m
n o p q r s t u v w x y z
0 1 2 3 4 5 6 7 8 9
the Function Setup switch
.
Repeat this to enter
←→CLR
POS
END
multiple letters You can enter up to 15 letters.
.
5) Enter a title, move the cursor to 'POS' and
press the Function Setup switch The entered
title appears on the screen Select the position
SHOP
.
.
to display the title on the screen by using the
Function Setup switch and press the Function
Setup switch When the position is determined,
.
select 'END' and press the Function Setup switch
to return to the SPECIAL menu.
NOTE
☞
■
When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if
you enter one.
■
■
Only English is available in this mode.
If you move the cursor to CLR and press the Function Setup switch, all the letters are
deleted
Setup switch
.
To edit a letter, change the cursor to the bottom left arrow and press the Function
Move the cursor over the letter to be edited, move the cursor to the letter to be
.
inserted and then press the Function Setup switch.
•
SYNC : In areas where the supply is at 60Hz(NTSC), 50Hz(PAL), you can synchronize the
output phase of multiple cameras using the power synchronization function (Line-Lock)
without using a synchronization signal generator.
- INT: Internal Synchronization Type
-L/L: Power Synchronization Type, Line-lock(AC24V Power)
* Press the Function Setup switch.
* You can select a desired phase from 0 to 359 when select 'phase'.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
NOTE
☞
■ When using AC power at 60Hz(NTSC), 50Hz(PAL), frequency, you can use the L/L type
synchronization.
■ When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode.
•
MOTION DET :This product has a feature that
MOT ON DET
allows you to observe movement of objects in
1 SENS T V TY
AREA1
ON
8
different areas on the screen, and the
2 AREA MODE
words
'MOTION DETECTED' appear on the
screen when
3 SEL POS
L TOP
4 XPOS
3
5
movement is detected.
5 YPOS
Activity can be monitor more efficiently.
6 F LL → SET
7 RETRUN
1) When the SPECIAL menu screen is displayed,
press the Function Setup switch so that the arrow
indicates 'MOTION DET’.
2) Set up the mode using the Function Setup switch.
- SENSITIVITY:You can select up to 8 MD areas When SENSITIVITY number is high, motion
.
detection sensitivity is increased to recognize even small movement.
- AREA MODE: Determines whether to use the MD area selected in SENSITIVITY.
- SEL POS: Determines which of the 4 vertices of each MD area is to be used.
- XPOS: Determines the coordinate of the horizontal axis for SEL POS.
- YPOS:Determines the coordinate of the vertical axis for SEL POS.
-
FILL→SET: Fills in a selected MD area
blue, cyan, green, yellow, magenta and red.
- RETURN:Select this to save the MOTION DET menu settings and return to the SPECIAL menu.
.
The color of the area can be selected from brown, orange,
•
PRIVACY: Mask an area you want to hide on the screen.
PR VACY AREA SETUP
1 AREA
2 MODE
3 MASK COLOR
4 MASK TONE
5 TOP
AREA1
OFF
GREEN
1
39
6 BOTTOM
7 LEFT
79
13
8 R GHT
52
9 RETURN
18
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
1) When the SPECIAL menu screen is displayed, press the Function Setup switch so
that the arrow indicates 'PRIVACY'.
2) Set up the mode using the Function Setup switch.
-AREA:You can select up to 12 PRIVACY areas.
- MODE:Determines whether to use the area selected in theAREA.
- MASK COLOR:Determine area color You can select Green, Red, Blue, Black, White, Gray.
.
- MASK TONE:Adjust the brightness of MASK COLOR.
- TOP/BOTTOM/LEFT/RIGHT:Adjustthe size and position of the selected area.
- RETURN:Select this to save the PRIVACYmenu settings andreturn to theSPECIALmenu.
•
MONITOR :
Please change the settings value of video appropriate to your monitor.
- LCD: Please select this menu item when using a LCD monitor.
- CRT:Please select this menu item when using a CRT monitor.
- USER:Please use this menu item when using a monitor other than standard ones
Change the gamma, PED level, and color gain in the sub menus.
.
You can
•
•
LANGUAGE: You can select the menu language according to your requirements.
RETURN:Select this to save the SPECIAL menu settings and return to the MAIN SETUP menu.
●
Exit Setting
Select a desired EXIT mode using the Function Setup Switch.
- SAVE: Save the current settings and exit the MAIN SETUP menu.
- NOT SAVE: Do not save the current settings and exit the MAIN SETUP menu.
- RESET: Resets the camera settings to the factory defaults
Monitor Settings are not initialized.
.
Language, Communication and
19
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
●
Trouble Shooting
PROBLEM
POSSIBLE CAUSE
☞
☞
Check the power cable, power supply output and video
connection between the camera and monitor.
Northing appears on
the screen.
Are the camera lens or the lens glass dirty?
Clean the lens / glass with a soft clean cloth.
Adjust the monitor controls, as required.
If the camera is facing a very strong light, change
the camera position.
The image on the
screen is dim.
☞
☞
☞
☞
Adjust the lens focus
Adjust the contrast control of the monitor.
The image on the
screen is dark.
☞
☞
If there is an intermediate device, correctly set the 75Ω/Hi-z.
Check the camera is correctly connected to an appropriate
regulated power source.
The camera is not
working properly
and the surface of
the camera is hot.
☞
☞
Has MOTION DET been set to ON in the menu?
Has MD AREA been properly defined?
Motion Detection
is not activated.
The color of the
☞
☞
Check the settings in WHITE BALANCE menu.
picture is not correct.
Make sure that the camera isn’t facing direct sunlight or
The image on the
screen flickers.
Fluorescent lighting If necessary, change the camera position.
.
☞
☞
Check that theAGC setting in the EXPOSURE menu isn't set to OFF.
Check the EXPOSURE menu and make sure SHUTTER is set to------.
The SENS-UP does
not work.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
USER’S MANUAL
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|