TELECOM
XEROX
Phaser 3100MFP/X
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Contents
Note to users in the United
CE Marking Traceability Information
Margin Shift with the Automatic
Activating / Deactivating the answering
Printing fax messages stored in the
- I -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Performing immediate transmission from
Consulting or modifying the waiting
Printing a document in waiting or in
Saving/Restoring the directory (Smart
Referring to or changing your network
An example of how an AD-HOC
Installing the drivers using the Xerox
Uninstall the drivers using the Xerox
Checking the connection between the
Download from Www.Somanuals.c-omII. -All Manuals Search And Download.
Phaser 3100MFP/X
Add a contact to the machine’s address
Add a group to the machine’s address
Delete a contact or a group from the
Send a fax from the hard disk or the
- III -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Security
Safety introduction
Notices and safety
Please read the following instructions carefully before operating the machine and refer to them as needed to
ensure the continued safe operation of your machine.
Your Xerox product and supplies have been designed and tested to meet strict safety requirements. These include
safety agency evaluation and certification, and compliance with electromagnetic regulations and established
environmental standards.
The safety and environment testing and performance of this product have been verified using Xerox materials only.
WARNING: Unauthorized alterations, which may include the addition of new functions or connection of external
devices, may impact the product certification. Please contact your Xerox representative for more information.
Marks, Labels
Symbols
All warnings and instructions marked on or supplied with the product should be followed.
WARNING: This symbol alerts users to areas of the equipment where there is the possibility of
personal injury.
WARNING: This symbol alerts users to areas of the equipment where there are heated or hot
surfaces, which should not be touched.
CAUTION: This symbol alerts users to areas of the equipment which require special attention to avoid
the possibility of personal injury or damage to the equipment.
WARNING: This symbol indicates a Laser is being used in the equipment and alerts the user to refer
to the appropriate safety information.
TIP: This symbol identifies information that is being emphasized and is important for you to remember.
EMC
Note to users in the United States of America
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
Download from Www.Somanuals.c-om1. -All Manuals Search And Download.
Phaser 3100MFP/X
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the
following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio / TV technician for help.
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
EME Compliance for Canada
This Class "B" digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe "B" est conforme à la norme NMB-003 du Canada.
Laser Safety Information
CAUTION: Use of controls, adjustments, or performance of procedures other than those specified in this guide
may result in hazardous light exposure.
This equipment complies with international safety standards and is classified as a Class 1 Laser Product.
With specific reference to lasers, the equipment complies with laser product performance standards set by
governmental, national, and international agencies as a Class 1 Laser Product. It does not emit hazardous light,
as the beam is totally enclosed during all phases of customer operation and maintenance.
For Europe/Asia
This machine complies with IEC 60825-1:1993+A1:1997+A2:2001 standard, is classified as laser class 1 product
and is safe for office/EDP use. It contains one class 3B laser diode, 10.72 mW max, 770-795 nm and other class
1 LEDs (280 µW at 639 nm).
Direct (or indirect reflected ) eye contact with the laser beam might cause serious eye damage. Safety precautions
and interlock mechanisms have been designed to prevent any possible laser beam exposure to the operator.
For North America
CDRH Regulations.
This equipment complies with the FDA performance standards for laser products except for deviations pursuant
to Laser Notice No.50, dated 24 June 2007 and contains 1 class 3B laser diode, 10.72 milliwatt, 770-795
nanometer wavelength and other class 1 LEDs (280 µW at 639 nm).
This equipment does not emit hazardous light, since the beam is totally enclosed during all customer modes of
operation and maintenance.
Operational Safety Information
Your Xerox equipment and supplies have been designed and tested to meet strict safety requirements. These
include safety agency examination, approval, and compliance with established environmental standards.
To ensure the continued safe operation of your Xerox equipment, follow these safety guidelines at all times:
Do These
• Always follow all warnings and instructions that are marked on or supplied with the equipment.
• Before cleaning this product, unplug the product from the electrical outlet. Always use materials specifically
designated for this product, the use of other materials may result in poor performance and create a hazardous
situation.
•
WARNING: Do not use aerosol cleaners. Aerosol cleaners can be explosive or flammable when
Download from Www.Somanuals.c-om2. -All Manuals Search And Download.
Phaser 3100MFP/X
used on electromechanical equipment.
• Always exercise care when moving or relocating equipment. Please contact your local Xerox Service Center to
arrange relocation of the copier to a location outside of your building.
• Always locate the machine on a solid support surface (not on plush carpet) that has adequate strength to support
the weight of the machine.
• Always locate the machine in an area that has adequate ventilation and room for servicing.
• Always unplug this equipment from the electrical outlet before cleaning.
• NOTE: Your Xerox machine is equipped with an energy saving device to conserve power when the machine is
not in use. The machine may be left on continuously.
•
WARNING: The metallic surfaces in the fuser area are hot. Please use caution when clearing paper
jams from this area and avoid touching any metallic surfaces.
Do Not Do These
• Never use a ground adapter plug to connect the equipment to a power outlet that lacks a ground connection
terminal.
• Never attempt any maintenance function that is not specifically described in this documentation.
• Never obstruct ventilation openings. They are provided to prevent overheating.
• Never remove covers or guards that are fastened with screws. There are no operator serviceable areas within
these covers.
• Never locate the machine near a radiator or any other heat source.
• Never push objects of any kind into the ventilation openings.
• Never override or "cheat" any of the electrical or mechanical interlock devices.
• Never place this equipment where people might step on or trip on the power cord.
• This equipment should not be placed in a room unless proper ventilation is provided. Please contact your local
Authorized dealer for further information.
Electrical Safety Information
1. The power receptacle for the machine must meet the requirements stated on the data plate on the rear of the
machine. If you are not sure that your electrical supply meets the requirements, please consult your local
power company or an electrician for advice.
2. The socket outlet shall be installed near the equipment and shall be easily accessible.
3. Use the power cable that is supplied with your machine. Do not use an extension cord or remove or modify the
power cord plug.
4. Plug the power cable directly into a correctly grounded electrical outlet. If you are not sure whether or not an
outlet is correctly grounded, consult an electrician.
5. Do not use an adapter to connect any Xerox equipment to an electrical outlet that lacks a ground connection
terminal.
6. Do not place this equipment where people might step or trip on the power cable.
7. Do not place objects on the power cable.
8. Do not override or disable electrical or mechanical interlock devices.
9. Do not push objects into slots or openings on the machine. Electrical shock or fire may result.
10. Do not obstruct ventilation openings. These openings are used to provide proper cooling to the Xerox machine.
Electrical Supply
1. This product shall be operated from the type of electrical supply indicted on the product's data plate label. If
you are not sure that your electrical supply meets the requirements, please consult a licensed electrician for
advice.
WARNING: This equipment must be connected to a protective earth circuit.
Download from Www.Somanuals.c-om3. -All Manuals Search And Download.
Phaser 3100MFP/X
This equipment is supplied with a plug that has a protective earth pin.
This plug will only fit into an earthed electrical outlet.
This is a safety feature. If you are unable to insert the plug into the outlet, contact a licensed electrician to
replace the outlet.
3. Always connect equipment to a correctly grounded power outlet. If in doubt, have the outlet checked by a
qualified electrician.
Disconnect device
The power cable is the disconnect device for this equipment. It is attached to the back of the machine as a plug-
in device. To remove all electrical power from the equipment, disconnect the power cable from the electrical outlet.
Emergency Power Off
If any of the following conditions occur, turn off the machine immediately and disconnect the power cable(s)
from the electrical outlet(s). Contact an authorized Xerox Service Representative to correct the problem:
• The equipment emits unusual odors or makes unusual noises.
• The power cable is damaged or frayed.
• A wall panel circuit breaker, fuse, or other safety device has been tripped.
• Liquid is spilled into the machine.
• The machine is exposed to water.
• Any part of the machine is damaged.
Ozone Information
This product produces ozone during normal operation. The ozone produced is heavier than air and is dependent
on copy volume. Install the system in a well-ventilated room.
If you need additional information about ozone, please request the Xerox publication Facts About Ozone (part
number 610P64653) by calling 1-800-828-6571 in the United States and Canada. In other markets, please contact
your local Xerox representative.
Maintenance Information
1. Any operator product maintenance procedures will be described in the user documentation supplied with the
product.
2. Do not carry out any maintenance on this product which is not described in the customer documentation.
3.
WARNING: Do not use aerosol cleaners. Aerosol cleaners can be explosive or flammable when
used on electromechanical equipment.
4. Use supplies and cleaning materials only as directed in the Operator section of this manual.
5. Do not remove covers or guards that are fastened with screws. There are no parts behind these covers that
you can maintain or service.
Consumables Information
1. Store all consumables in accordance with the instructions given on the package or container.
2. Keep all consumables away from the reach of children.
3. Never throw print cartridges into an open flame.
4. Print Cartridges: When handing print cartridges, fusers, etc, avoid skin or eye contact. Eye contact can cause
irritation and inflammation. Do not attempt to disassemble the cartridge. This can increase the risk of skin or
eye contact.
Download from Www.Somanuals.c-om4. -All Manuals Search And Download.
Phaser 3100MFP/X
Product Safety Certification
EUROPE: This XEROX product is certified by the following Agency using the Safety Standards listed.
Agency: TUV Rheinland
Standard: IEC 60950-1
USA/CANADA: This XEROX product is certified by the following Agency using the Safety Standards listed.
Agency: UNDERWRITERS LABORATORIES INC.
Standard: UL 60950-1. Certification is based on reciprocity agreements, which include requirements for
Canada.
Regulatory Information
Certifications in Europe
The CE mark applied to this product, symbolizes XEROX's declaration of
conformity with the following applicable European Union Directives, as of
the dates indicated:
CE
December 12,2006: Council Directive 2006/95/EC as amended. Approximation of the laws of the
member states related to low voltage equipment.
December 15, 2004: Council Directive 2004/108/EC as amended. Approximation of the laws of
the member states related to electromagnetic compatibility.
March 9, 1999: Council Directive 99/5/EC, on radio equipment and telecommunications
terminal equipment and the mutual recognition of the conformity.
A full declaration of conformity, defining the relevant directives and
referenced standards, can be obtained from your XEROX Limited
representative.
CE Marking Traceability Information (For EU Countries Only)
Manufacturer:
Xerox Ltd.
Bessemer Rd
Welwyn Gdn City
Herts AL7 1BU - ENGLAND
Regulatory information for the Fax function
USA
FAX Send Header Requirements:
The telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other
electronic device, including a Fax machine, to send any message unless such message clearly contains in a
margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it
is sent and an identification of the business or other entity, or other individual sending the message and the
telephone number of the sending machine or such business, other entity or individual. (The telephone number
provided may not be a 900 number or any other number for which charges exceed local or long distance
transmission charges.)
In order to program this information into your FAX machine refer to Installation and follow the steps provided.
Data Coupler Information:
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative
Council for Terminal Attachments (ACTA). On the rear of this equipment is a label that contains, among other
information, a product identifier in the format US:AAAEQ##TXXXX. If requested , this number must be provided
to the Telephone Company.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with
the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular
Download from Www.Somanuals.c-om5. -All Manuals Search And Download.
Phaser 3100MFP/X
plug is provided with this product. It is designed to be connected to a compatible modular jack that is also
compliant. See installation instructions for details.
You may safely connect the machine to the following standard modular jack: USOC RJ-11C using the compliant
telephone line cord (with modular plugs) provided with the installation kit. See installation instructions for details.
The Ringer Equivalence Number (or REN) is used to determine the number of devices that may be connected to
a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an
incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number
of devices that may be connected to a line, as determined by the total RENs, contact the local Telephone
Company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that
has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03
is a REN of 0.3). For earlier products, the REN is separately shown on the label.
If this Xerox equipment causes harm to the telephone network, the Telephone Company will notify you in advance
that temporary discontinuance of service may be required. If advance notice isn't practical, the Telephone
Company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint
with the FCC if you believe it is necessary.
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect
the operation of the equipment. If this happens the Telephone Company will provide advance notice in order for
you to make necessary modifications to maintain uninterrupted service.
If trouble is experienced with this Xerox equipment, for repair or warranty information, please contact the
appropriate service center; details of which are displayed either on the machine or contained within the user guide.
If the equipment is causing harm to the telephone network, the Telephone Company may request that you
disconnect the equipment until the problem is resolved.
Repairs to the machine should be made only by a Xerox representative or an authorized Xerox service agency.
This applies at any time during or after the service warranty period. If unauthorized repair is performed, the
remainder of the warranty period is null and void. This equipment must not be used on party lines. Connection to
party line service is subject to state tariffs. Contact the state public utility commission, public service commission
or corporation commission for information.
If your office has specially wired alarm equipment connected to the telephone line, ensure the installation of this
Xerox equipment does not disable your alarm equipment. If you have questions about what will disable alarm
equipment, consult your Telephone Company or a qualified installer.
Canada
This product meets the applicable Industry Canada technical specifications.
NOTE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the
maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface
may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence
Numbers of all of the devices does not exceed 5.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs
or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone
lines and internal metallic water pipe systems, if present, are connected together. This precaution may be
particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate.
Download from Www.Somanuals.c-om6. -All Manuals Search And Download.
Phaser 3100MFP/X
Europe
Radio Equipment & Telecommunications Terminal Equipment Directive
This Xerox product has been self-certified by Xerox for pan-European single terminal connection to the analogue
public switched telephone network (PSTN) in accordance with Directive 1999/5/EC.
The product has been designed to work with the national PSTNs of the following countries:
Austria
Finland
France
Italy
Norway
Poland
Sweden
Belgium
Latvia
Switzerland
United
Kingdom
Bulgaria
Cyprus
Germany
Greece
Liechtenstein
Lithuania
Portugal
Romania
Slovakia
Czech
Republic
Hungary
Luxembourg
Denmark
Estonia
Iceland
Ireland
Malta
Slovenia
Spain
Netherlands
In the event of problems, you should contact your local Xerox representative in the first instance.
This product has been tested to and is compliant with TBR21 or ES 103 021-1/2/3 or ES 203 021-1/2/3, technical
specifications for terminal equipment for use on analogue-switched telephone networks in the European Economic
Area.
The product may be configured to be compatible with other country networks. Please contact your Xerox
representative if it needs to be reconnected to another country's network.
NOTE: Although this product can use either loop disconnect (pulse) or DTMF (tone) signaling it is recommended
that it is set to use DTMF signaling. DTMF signaling provides reliable and faster call setup.
Modification, connection to external control software or to external control apparatus not authorized by Xerox, will
invalidate its certification.
Product Recycling and Disposal
USA and Canada
Xerox operates a worldwide equipment take back and reuse/recycle program. Contact your Xerox sales
If your product is not part of the Xerox program and you are managing its disposal, please note that the product
may contain lead and other materials whose disposal may be regulated due to environmental considerations. For
European Union
WEEE Directive 2002/96/EC
Some equipment may be used in both a domestic/household and a professional/business application.
Professional/Business Environment
Application of this symbol on your equipment is confirmation that you must dispose of this equipment in compliance
with agreed national procedures. In accordance with European legislation, end of life electrical and electronic
equipment subject to disposal must be managed within agreed procedures.
Download from Www.Somanuals.c-om7. -All Manuals Search And Download.
Phaser 3100MFP/X
Domestic/Household Environment
Application of this symbol on your equipment is confirmation that you should not dispose of the equipment in the
normal household waste stream. In accordance with European legislation, end of life electrical and electronic
equipment subject to disposal must be segregated from household waste.
Private households within EU member states may return used electrical and electronic equipment to designated
collection facilities free of charge. Please contact your local disposal authority for information.
In some member states, when you purchase new equipment, your local retailer may be required to take back your
old equipment free of charge. Please ask you retailer for information. Prior to disposal, please contact your local
dealer or Xerox representative for end of life takeback information.
North America (USA, Canada)
PRODUCT ENVIRONMENT REQUIREMENTS
Xerox operates a worldwide equipment take back and reuse/recycle program. Contact your Xerox sales
representative (1-800-ASK-XEROX) to determine whether this Xerox product is part of the program. For more
If you are managing the disposal of your Xerox product, please note that the product may contain lead, mercury,
Perchlorate, and other materials whose disposal may be regulated due to environmental considerations. The
placed on the market. For recycling and disposal information, contact your local authorities. In the United States,
Perchlorate Material - This product may contain one or more Perchlorate-containing devices, such as batteries.
Energy Program Compliance
Energy star
As an ENERGY STAR® partner, Xerox Corporation has determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
The ENERGY STAR and ENERGY STAR MARK are registered United States trademarks. The
ENERGY STAR Imaging Equipment Program is a team effort between U.S., European Union and
Japanese governments and the office equipment industry to promote energy-efficient copiers,
printers, fax, multifunction machine, personal computers, and monitors. Reducing product energy
consumption helps combat smog, acid rain and long-term changes to the climate by decreasing the
emissions that result from generating electricity.
Xerox ENERGY STAR equipment is preset at the factory. Your machine will be delivered with the timer
for switching to Power Save Mode from the last copy/print out, set at 5 or 15 minutes, depending on
the model. A more detailed description of this feature can be found in the Machine Setup Section of
this guide.
Section 16 EH&S Contact Information
Contact Information
For more information on Environment, Health, and Safety in relation to this Xerox product and supplies, please
contact the following customer help lines:
USA:
1-800 828-6571
1-800 828-6571
+44 1707 353 434
Canada:
Europe:
Download from Www.Somanuals.c-om8. -All Manuals Search And Download.
Phaser 3100MFP/X
Security directives
Before turning on your device, check that the outlet that you are going to plug it into conforms to the indications shown
on the information plate (voltage, current, power network frequency) located on your device. This device shall be
connected to a single phase power network. The device shall not be installed on bare ground.
Batteries and rechargeable batteries, packaging and electric and electronic equipment (EEE), shall be thrown away,
as specified by the Instructions of the ENVIRONMENT chapter of this manual.
Because of the device model, the power connector is the only way to disconnecting the device from the power network,
that is why it is imperative to apply the following safety measures: your device shall be connected to a power outlet
located nearby. The outlet shall be easily accessible.
Your device is delivered with a grounded power cord. It is imperative to connect a grounded connector to a grounded
outlet connected to the building earthing.
Repairs-maintenance: Repairs and maintenance should only be carried out by a
qualified technician. There are no serviceable parts inside the machine. To reduce
the risk of electrical shock, you shall not proceed with these operations yourself,
because by opening or removing the covers, you could expose yourself to two
hazards:
- The laser beam can cause irreversible eye damage.
- Avoid contact with powered parts because it can lead to electrical shock with
unfortunate consequences.
Download from Www.Somanuals.c-om9. -All Manuals Search And Download.
Phaser 3100MFP/X
Positions of Safety labels on the machine
The device has warning labels at the positions shown below. For your safety, you must never touch these surfaces
when you remove a paper jam or when you replace the Toner cartridge.
Symbols for the main power switch
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
-
-
means POWER ON.
means POWER OFF.
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Software use license
CAREFULLY READ ALL THE TERMS AND CONDITIONS OF THE PRESENT LICENSE BEFORE OPENING THE
SEALED ENVELOPE CONTAINING THE SOFTWARE. OPENING THIS ENVELOPE INDICATES THAT YOU
ACCEPT THESE TERMS AND CONDITIONS.
In case you should not accept the terms of this license, the CD-ROM packaging should be returned to the retailer
unopened, along with the other components of the product. The purchase price of this product will be refunded. No
refunds will be made for products if the CD-ROM packaging have been opened, if components are missing or if the
reimbursement request is made after ten (10) days from the purchase date, your receipt is the proof of purchase.
Definition
The Software designates programs and associated documentation.
License
- This license allows you to use this Software on personal computers on a local network. You only have permission to
use this Software to print on one multifunction machine; you can not lend the Software or authorize anyone to use it.
- You are allowed to make a back up copy.
- This license is non-exclusive and non-transferable.
Property
The manufacturer or its providers hold the Software property right. You only become the owner of the CD-ROM. You
shall not modify, adapt, decompile, translate, create any derived piece, rent or sell the Software or the documentation.
Any rights not explicitly approved are reserved by the manufacturer or its providers.
Duration
This license remains valid until cancelled. You can cancel it by destroying the program and the documentation as well
as any other copies of them. This license will automatically be canceled in case you do not respect the terms of this
license. If the license is rendered invalid, you agree to destroy all copies of the program and the associate
documentation.
Warranty
The Software is provided "as is" with no warranties what so ever, whether expressed or implied, including without
limitation, any warranties of merchantability or fitness for a particular purpose; all the risks concerning the results and
performance of this Software are assumed by the buyer. In case the program should appear defective, all the repair
and service expenses will be covered by the buyer.
Nevertheless, the license holder benefits from the following warranty: we guarantee that the CD-ROM on which the
Software is recorded is free from hardware or manufacturing faults if used in normal conditions, the guarantee is valid
for ninety (90) days from the delivery date, the copy of the receipt being the proof of purchase. In case of a CD-ROM
fault that due to accident or misuse, the CD-ROM will not be replaced as per the warranty.
Responsibility
If the CD-ROM is not working properly, send it to the retailer together with a copy of the receipt. It is the retailer's sole
responsibility to replace the CD-ROM. Nobody, not even the manufacturer who is involved in the creation, realization,
merchantability and delivery of this program would be responsible for direct, indirect or immaterial damages, such as,
but not limited to, loss of information, loss of time, execution loss, loss of revenue, loss of customers, due to the use or
inability to use the program.
Development
With a constant concern for improvement, the manufacturer reserves the right to modify the Software specifications
without any notice. In case of modification, your user right does not give you access to free updates.
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Applicable law
This license is under the French law. Any dispute following the interpretation or execution of this license will be
submitted to the Paris Court.
Given the continuous technology development, the manufacturer reserves the right to modify the technical
specifications indicated for this product, at any time, without prior notice, and/or to stop manufacturing of the product.
All the names of the products and brands that could be trademarks registered by their respective owners are
recognized in the present document.
Registered trademarks
Given the technical evolution, Sagem Communications reserves the right to modify the technical specifications of this
product and/or to stop its manufacturing at any time and without notice. Xerox Companion Suite is a registered
trademark of Sagem Communications.
Adobe® and the Adobe® products referred to here are registered trademarks of Adobe Systems Incorporated.
PaperPort11SE is a registered trademark of ScanSoft.
Microsoft® Windows 2000®, Microsoft® Windows Server 2003®, Microsoft® Windows XP®, Microsoft® Windows
Vista® and any other Microsoft® product referred to here are registered trademarks of Microsoft Corporation registered
and/or used in the United States and/or in other countries.
All the other brands or products referred to as examples or in order to give additional information are registered
trademarks of their respective owners.
The informations contents of this user manual are subject to change without notice.
Prohibited reproductions
Do not copy or print any item for which reproduction is prohibited by law.
Copying or printing the following items is generally prohibited by local law:
- bank notes;
- checks;
- bonds;
- stock certificates;
- bank drafts;
- passports;
- driver's licenses.
The preceding list is meant as a guide only and is not inclusive. If you have any questions concerning the legality of
copying or printing certain items, consult with your legal advisor.
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Installation
Location conditions
By choosing an appropriate location, you preserve the longevity of the machine. Check that the selected location has
the following characteristics:
- Choose a well ventilated location.
- Make sure not to obstruct the ventilation grids located on the left and right sides of the device. During the
installation, make sure to place the machine thirty centimeters away from the surrounding objects so all the covers
can be easily opened.
- Make sure that this location does not present any ammonia nor any other organic gasses emission hazard.
- The ground outlet (refer to the security notices presented in the Security chapter) to which you plan to connect
the machine must be located close to this one and have an easy access.
- Make sure that the machine is not directly exposed to sun light.
- Make sure not to place the machine in an area exposed to an air flow generated by an air conditioning, heating or
ventilation system, nor in an area subject to large temperature or humidity variations.
- Choose a solid and horizontal surface on which the machine will not be exposed to intense vibrations.
- Keep the machine away from any object that could obstruct its ventilation ports.
- Do not place the machine close to hangings or any other flammable objects.
- Choose a location where exposure to water and other liquids will not occur.
- Make sure that this location is dry, clean and dust free.
Cautions of use
Take into account the important precautions below when using the machine.
Running environment:
- Temperature: 10 °C to 27 °C [50 °F to 80.6 °F] with an ambient humidity included between 15 to 80% (up to 32°C
[89.6 °F] with an ambient humidity included between 15 to 54%).
Machine:
The section below describes the precautions to be taken when using the machine:
- Never turn the machine off and never open the covers while printing.
- Never use gas or flammable liquids, or objects generating magnetic field close to the machine.
- When you unplug the power cord, always grasp the connector and not the cord. A damaged cord presents a
potential fire hazard or an electric shock hazard.
- Never touch the power cord with wet hands. You risk getting an electric shock.
- Always unplug the power cord before moving the machine. Otherwise, you could risk having the cord damaged
and create a fire hazard or an electric shock hazard.
- Always unplug the power cord when you plan not to use the machine for a long period of time.
- Never put objects on the power cord, never pull it and never fold it. This could cause a fire hazard or an electric
shock hazard.
- Always make sure that the machine is not sitting on the power cord or any other electric device communication
cables. Make sure no cables or cords get trapped inside the machine. This would expose you to a machine
malfunction risk or to a fire hazard.
- Make sure that the printer is unplugged from the power outlet before connecting or disconnecting an interface
cable to the printer (use a shielded interface cable).
- Never try to remove any fixed panel or cover. The machine contains high voltage circuits. Any contact with these
circuits can cause an electric shock risk.
- Never try to modify the machine. This could cause a fire hazard or an electric shock hazard.
- Always make sure that paper clips, staples or other small metallic items do not get inside the machine via the
ventilation ports or other ports. Such items create fire hazards or electric shock hazards.
- Prevent water and any other liquid from spilling on the machine or near to it. Any contact of the machine with water
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
or liquid can cause a fire hazard or an electric shock hazard.
- If liquid or metallic item gets accidentally inside the machine, turn it off immediately, unplug the power cord and
contact your retailer. Otherwise, you will face a fire hazard or an electric shock hazard.
- In case of heat, smoke, unusual smell or abnormal noise emissions, turn the machine off, unplug the power cord
immediately and contact your retailer. Otherwise, you will face a fire hazard or an electric shock hazard.
- Avoid using the machine during an "electric storm", this can cause an electric shock hazard due to lightning.
- Never move the machine during printing.
- Always lift the machine when you wish to move it.
Make sure to place the machine in well ventilated premises. When in operation, the printer generates
a small amount of ozone. An unpleasant smell can come from the printer if it is used intensively in
poorly ventilated premises. For safety purposes, make sure you place the machine in a well ventilated
area.
Safety information
When using your product, the following safety precautions should always be followed.
Safety During Operation
In this section, the following symbols are used:
Indicates a potentially hazardous situation which, if instructions are not followed, could
WARNING:
CAUTION:
result in death or serious injury.
Indicates a potentially hazardous situation which, if instructions are not followed, may result in
minor or moderate injury or damage to property.
WARNING
- Connect the power cord directly into a wall outlet and never use an extension cord.
- Disconnect the power plug (by pulling the plug, not the cable) if the power cable or plug becomes frayed or
otherwise damaged.
- To avoid hazardous electric shock or laser radiation exposure, do not remove any covers or screws other than
those specified in the Operating instructions.
- Turn off the power and disconnect the power plug (by pulling the plug, not the cable) if any of the following
conditions exists:
•
•
•
You spill something into the product.
You suspect that your product needs service or repair.
Your product’s cover has been damaged.
- Do not incinerate spilled toner or used toner. Toner dust might ignite when exposed to an open flame.
- Disposal can take place at our authorised dealer or at appropriate collection sites.
- Dispose of the used print cartridge in accordance with local regulations.
CAUTION
- Protect the product from dampness or wet weather, such as rain, snow, and so on.
- Unplug the power cord from the wall outlet before you move the product. While moving the product, you should
take care that the power cord will not be damaged under the product.
- When you disconnect the power plug from the wall outlet, always pull the plug (not the cable).
- Do not allow paper clips, staples, or other small metallic objects to fall inside the product.
- Keep print cartridges out of the reach of children.
- Be careful not to cut yourself on any sharp edges when you reach inside the machine to remove misfed sheets of
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
paper or originals.
- For environmental reasons, do not dispose of the product or expended supply wastes at household waste
collection point. Disposal can take place at our authorised dealer or at appropriate collection sites.
- Our products are engineered to meet the high standards of quality and functionality, and we recommend that you
only use the expendable supplies available at an authorised dealer.
Power Supply
The power outlet should be close to the machine and should be easily accessible.
For Fax or Telephone
- Do not use this product near water, for example near bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.
- Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of an
electric shock from lightning.
- Do not use a telephone in the vicinity of a gas leak to report the leak.
Paper recommendations
Loading paper in the main paper tray
•
Insert the paper face down and adjust the paper guides to the paper size to avoid feed failure, skewing and paper
jams.
•
Amount of loaded paper must not exceed the loading mark. If the loading mark is exceeded, this may cause feed
failure, skewing, and paper jams.
•
•
•
Adding paper during printing must be avoided because it may cause multi-feeds.
When removing the paper tray from the machine, always support it with both hands to avoid dropping it.
If you use paper already printed by your machine or another printer, the printing quality may not be optimal.
Handling of paper
•
•
•
Curling must be corrected before printing.
Curls must not exceed 10 mm.
Care must be taken with storage to prevent feed faults and image defects due to leaving the paper in conditions of
high humidity.
Humidity control
•
•
•
Paper which has become damp, or paper which has been left unused for a very long time, must not be used.
After opening the paper, it must be kept in a plastic bag.
Paper with waved ends, paper which is creased, paper with crumples, and any other non-normal paper must not
be used.
Handling the machine
Operator shocks
During printing, avoid shocks due to static electricity applied to the paper tray, covers and other parts of the machine.
Moving the machine
When moving the machine on a desk, it must be lifted and not dragged.
Handling the print cartridge
•
•
Must not be stood on the side, or held upside down.
Must not be shaken strongly.
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Rules for use symbols
WARNING
Indicates important safety notes.
Ignoring these notes could result in serious injury or death. Be sure to read these notes. They can be found in the Safety
information section of this manual.
CAUTION
Indicates important safety notes.
Ignoring these notes could result in moderate or minor injury, or damage to the machine or to property. Be sure to read
Important
Indicates points to pay attention to when using the machine, and explanations of likely causes of paper misfeeds,
damage to originals, or loss of data. Be sure to read these explanations.
Note
Indicates supplementary explanations of the machine’s functions, and instructions on resolving user errors.
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Machine Overview
Front and Back sides
1. Control panel
10. Master USB interface connector (USB key)
2. Document feeder
11. Manual paper feed setup guides
12. Manual input tray
3. Paper jam cover
4. Power supply cord connection
5. On/Off switch
13. Paper tray
14. Print cartridge access cover
15. Output support
6. LINE port - telephone cable connection
7. EXT. port - connection for external telephone devices
8. Slave USB interface connector (for PC)
9. Master USB interface connector (USB key)
16. Paper output
17. Smart card insertion slot
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Control panel
1. Screen.
16. Key
: start.
2. Digital keypad.
3. Alphabetical keypad.
17. Key OK: confirms the displayed selection.
18. Key
19. Key
20. Key
ꢀ
: menu access and navigation down the menus.
4. Key
5. Key
Í
: deletes the character to the left of the cursor.
: input or line feed.
C
: back to the previous menu and input correction.
ꢁ
: navigation up the menus.
: stops the current operation.
6. Key
7. Key
8. Key
: access to special characters.
21. Key
22. Key
23. Key
:
Shift.
: sets up the activation delay.
: document scan to the PC or an external
: access to print menu (print functions list,
storage device (USB key).
machine settings, etc.).
9. Key
: copy.
24. Key : scan resolution setup.
10. Key
11. Key
12. Key
13. Key
14. Key
: stops the current PC print job.
: sending of an SMS (Short Message Service).
: fax.
25. Key
: contrast setup.
26. Icon
27. Icon
28. Icon
29. Icon
: resolution "Copy: Quality Text / Fax: SFine".
: resolution "Photo".
: resolution "Copy: Text / Fax: Fine".
: colour mode.
: address book.
:
manual telephone line connection, listen for
30. Icon
31. Icon
32. Icon
: activity on the telephone line.
: Fax mode.
tone during fax transmission.
15. Key : broadcast transmission (fax, email or SMS).
: external answering machine mode.
Accessing menus
All functions and settings are available via the menu and are associated with a specific menu command.
For example, the menu command 51 launches the printing of the functions list (the functions list stores the list of all
menus, sub-menus and their identification number).
Two methods are available to access menu items: the step by step method or the shortcut method.
To print the functions list with the Step by step method:
1 Press ꢀ.
2 Use the ꢀor ꢁbutton to browse the menu and select 5 - PRINT. Confirm with OK.
3 Use the ꢀor ꢁbutton to browse the menu PRINT and select 51-FUNCTIONS LIST. Confirm with OK.
To print the functions list with the shortcut method:
1 Press ꢀ.
2 Enter 51 from the numerical keypad to directly print the functions list.
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Packaging contents
Device installation
The packaging contains the items listed below:
1 Unpack the device.
2 Install the device adhering to the security notices
Multifunction device
stated at the beginning of this booklet.
3 Remove all tape from the machine.
4 Remove the plastic protection film from the screen.
Installing the document feeder
1 Secure the document feeder by fitting the two clips
(B) in the notches (A) provided for this purpose.
1 print cartridge
Paper tray installation
Before loading paper, refer to the
1 Safety guide and 1 Installation guide
Important
Your machine supports a number of sizes and types of
1 PC installation CD ROM and 1 OCR PC software CD
ROM (depending on model)
You can use paper weighing
Important
between 60 and 105 g/m2.
1 Remove the paper tray completely.
1 power cord
1 telephone cord (only North America)
1 USB cord
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Print cartridge installation
2 Push the lower panel down until it clicks.
1 Stand in front of the machine.
2 Grasp the left and right sides of the cover and pull
it towards you at the same time.
3 Setup the back side tray stop by pushing the
"PUSH" level (A).
Then adjust the side paper guides to the paper size
by pushing lever (B) located on the left side guide.
Adjust the length paper guide to the paper size by
pushing lever (C).
3 Unpack the new print cartridge. Gently roll the
cartridge 5 or 6 times to distribute the toner evenly
inside the cartridge. Thoroughly rolling the
cartridge will assure the maximum copies per
cartridge.
Hold it by its handle.
4 Insert the cartridge in its slot by pushing it until it
clicks, then gently push the handle down (as shown
below).
4 Take a paper stack, pull the paper off and align it
on a flat surface.
5 Put the paper stack in the tray (200 sheets of 80 g/
m² paper for instance).
6 Slide the tray back in its location.
5 Close the cover.
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Output Support Tab
Adjust the paper output support tab depending on the size
of the document to be printed. Do not forget to raise the
flap to prevent output sheets from falling out of the
machine.
The power cord is used as a power
unit cut off. As a precaution, the
outlet shall be located close to the
device and be of easy access in
case of danger.
WARNING
4 Press the On/Off button to turn on the device
(I position).
Starting your device
Device initial setup
After a few seconds, when the machine has warmed up,
the Easy Install function is launched and the LCD screen
displays the following message:
Device connection
Before plugging the power cord, it
is imperative to refer to the
SET LANGUAGE
YES=OK - NO=C
WARNING
1 Plug the end of the telephone line into the machine
socket and the other end into the wall telephone
socket.
The Easy Install function will help you configure your
machine by guiding you through the basic settings.
If you wish to modify the setting displayed, press the OK
button. If you do not want to modify the displayed setting,
press the C button: the Easy Install function then
displays the next basic setting.
If you do not want to carry out the
initial setup, press the
button. A
confirmation message appears. Press
Note
the button again to confirm.
To manually modify and customise the
machine settings, refer to
1 To modify the display language, press the OK
button.
2 Make sure that the On/Off switch is on Off
2 Select the desired language using the ꢁor ꢀ
buttons and confirm with OK.
(O position).
3 Connect the power cord to the device.
3 To set the country, press the OK button.
Plug the power cord into the wall outlet.
SET COUNTRY
YES=OK - NO=C
- 21 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
4 Select your country in the list displayed using the ꢁ
or ꢀbuttons and confirm with OK.
length for France).
Use C to correct an entry.
Press the OK button to confirm.
If none of the options in the list is
Note
13 Enter the local prefix number (10 characters max.)
using the numerical keypad.
suitable, select the "OTHER" option.
This prefix will automatically be added when an
external number is dialled.
To insert a pause for dial tone ("/" sign), press
simultaneously the CTRL and M keys, or long press
the 0 (zero) key on the numerical keypad until the
"/" sign is displayed.
5 If you have set the country to "Other", you may
need to set the public telephone NETWORK to use.
Press the OK button to specify it.
SET NETWORK
YES=OK - NO=C
Use the C button to correct an entry.
Press the OK button to confirm.
Select the telephone network to use in the list
displayed using the ꢁor ꢀbuttons and confirm
with OK.
The setup is now complete and the functions list is
automatically printed out.
If none of the options in the list is
Note
suitable, select the "OTHER" option.
The LCD screen displays the message PAPER EMPTY if no
paper has been loaded in the paper tray (see Loading
been loaded, printing will resume.
6 To set the date and time, press the OK button.
DATE/TIME
YES=OK - NO=C
Loading paper in the manual feed tray
7 Enter the numbers of the required date and time
one after another using the numerical keypad.
The date format depends on the country you have
selected: for instance, DDMMYY for France,
MMDDYY for the USA.
Before loading paper, refer to the
Important
Use the C button to correct an entry.
Press OK to confirm.
The manual feed tray allows you to use a greater variety
of weights and sizes than those used in the main paper
8 To specify the fax number and machine name,
press the OK button.
This information will appear on your transmitted
documents when the "Sending Header" function is
activated.
Only one sheet or envelope can be fed at a time.
You can use paper weighing
Important
between 52 and 160 g/m².
NUMBER/NAME
YES=OK - NO=C
1 Spread the manual feed guides to the maximum.
9 Enter your fax number (20 digits max.) using the
numerical keypad.
To type the "+" sign, press simultaneously the CTRL
and Q keys.
Use the C button to correct an entry.
Press the OK button to confirm.
10 Enter your machine name (20 characters max.)
using the alphanumerical keypad.
Press the OK button to confirm.
11 If you are connecting your machine to a private
network, behind a company’s PABX, you may need
to specify a local prefix. This prefix will be then
used to exit the company’s telephone network.
To set up this function, press the OK button.
2 Insert a sheet or an envelope in the manual feed
tray.
3 Adjust the paper guides against the right and left
edges of the sheet or the envelope.
PREFIX
4 Print making sure that the chosen paper size
corresponds to the selected format on the printer
YES=OK - NO=C
12 Enter the minimal size of the company’s outside
numbers (1 to 30) using the numerical keypad.
This setting is used to differentiate internal
telephone numbers from external telephone
numbers.
For example, if you are installing the machine in
France, behind your company’s PABX, enter 10
(10 digits being the standard telephone number
- 22 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Use of envelopes
•
•
Feeding can be done only through the manual feed.
Recommended area should be the area which
excludes 15 mm from the leading edge, 10 mm from
both the left and right edges, and the rear edge.
•
•
A few lines may be given in solid print at the part of
being overlapped.
Envelopes which are not recommended may lead to
improper printing (refer to the paragraph
•
•
Curled envelope after printing should be fixed
manually.
Small wrinkles on the edge of the wide side of
envelopes, smearing, or less clear printing may
appear on the reverse side.
•
•
•
Gently press the envelope to release any air before
loading it into the manual feed tray.
Load envelope in a proper position after aligning in
case it is bent or warped.
Paper conditioning is not allowed. And it should be
used under normal office environment.
- 23 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
2 Press the
button.
Copy
3 Enter the number of copies that you want and
confirm with the OK button.
Your machine has the ability to make one or more copies.
4 Choose the paper tray AUTOMATIC or MANUAL
with the buttons ꢁor ꢀ, then confirm with the OK
button.
You can also set up several parameters in order to make
copies at your will.
5 Choose with the buttons ꢁor ꢀthe printing option
(see examples below) depending on the copy
mode that you want:
Simple copy
-
n-Up (document feeder): 1 Page onto 1,
In this case, the default parameters are applied.
2 Pages onto 1, or 4 Pages onto 1.
1 Place the document to be copied face up in the
automatic document feeder.
or
Place the document face down on the document
glass, aligned with the registration arrows near the
top left of the document glass.
2 Press the
button twice. The copy is made
using the default parameters.
ECO mode copy
The ECO mode enables you to reduce the amount of
toner consumed on the page so as to save your printing
costs.
When the ECO mode is used, the toner consumption is
reduced and the print density becomes lighter.
1 Place the document to be copied face up in the
automatic document feeder.
or
Place the document face down on the document
glass, aligned with the registration arrows near the
top left of the document glass.
2 Press the
3 Press the
button.
button.
- Poster mode (document glass): 1 Page to 1,
1 Page to 4 or 1 page to 9.
Advanced copying
Advanced copy allows the user to do custom setups for
the current copy job.
You can start copy by pressing the
Note
button at any time in below
steps.
1 Place the document to be copied face up in the
automatic document feeder.
or
Place the document face down on the document
glass, aligned with the registration arrows near the
top left of the document glass.
After step 1, you can directly enter the
number of copies with the numerical
keypad and press the OK button to
Note
confirm. Then refer to step 4.
Confirm with the OK button.
- 24 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
6 Adjust the desired zoom level, from 25% TO 400%
with the buttons ꢁ or ꢀ, confirm with the OK
button (only available in 1 Page to 1 copy mode).
7 Adjust the contrast level with the buttons ꢁ or ꢀ,
then confirm with the OK button.
8 Adjust the desired brightness level with the buttons
ꢁor ꢀ, then confirm with the OK button.
7 Adjust the desired origin values with the digital
keyboard buttons ꢁor ꢀthen confirm with the OK
button.
9 Choose the paper type NORMAL, THICK with the
buttons ꢁor ꢀ, then confirm with the OK button.
The LCD screen displays the following message:
8 Choose the resolution depending on the printing
quality that you want AUTO, TEXT, PHOTO or
QUALITY TEXT with the buttons ꢁ or ꢀ, then
confirm with the OK button.
PUT ID CARD
THEN OK
9 Adjust the contrast level with the buttons ꢁ or ꢀ,
then confirm with the OK button.
10 Place your identity card or any other official
document against the document glass, as shown
below:
10 Adjust the desired brightness level with the buttons
ꢁor ꢀ, then confirm with the OK button.
11 Choose the paper type NORMAL, THICK with the
buttons ꢁor ꢀ, then confirm with the OK button.
ID Card Copy mode
The ID CARD copy function is used for copying both sides
of an identity card or driver’s license type document on an
A4 format sheet (original document size < A5) or on a
Letter format sheet (original document size < Statement).
The LCD screen displays useful operating instructions
(when the original document should be placed, when the
document should be turned over, etc.) and asks for your
confirmation to proceed with the operation.
11 Press the OK button.
The document is scanned then the LCD screen
displays the following message:
TURN UP DOC
THEN OK
This function is available only if the
document to be copied is placed on
the document glass, and if no paper
is detected in the automatic
document feeder.
12 Turn your document over then confirm with the
OK button.
Important
The machine prints out a copy of your document.
Zoom and Origin adjustments are
not available in this copy mode.
Special setups for copying
1 Make sure that there is no document in the
automatic document feeder.
Setups done through this menu become the device
default setups after you confirm.
2 Press the
button.
3 Enter the desired number of copies and confirm
with the OK button.
When the quality of the printing is
not satisfying, you can perform a
calibration (see Calibrate your
Important
4 Choose the paper tray AUTOMATIC or MANUAL
with the buttons ꢁor ꢀ, then confirm with the OK
button.
Resolution setup
Copying in ID Card mode is only
possible on A4 (original document
size < A5) or Letter (original
The RESOLUTION parameter allows you to setup the
photocopy resolution.
document size < Statement) paper
size. Make sure that the selected
paper tray uses the correct paper
size.
Important
ꢀ841 - ADVANCED FCT/COPY/RESOLUTION
1 Press ꢀ, enter 841 using the keypad.
2 Choose the resolution with the buttons ꢁ or ꢀ
5 Choose the copying option ID CARD with the
buttons ꢁor ꢀand confirm with the OK button.
6 Choose the resolution depending on the desired
printing quality AUTO, TEXT, PHOTO or QUALITY
TEXT with the buttons ꢁ or ꢀ, then confirm with
the OK button. For optimal results with ID
documents, select the PHOTO resolution.
- 25 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
according to the following table:
3 Confirm your choice by pressing the OK button.
4 Exit this menu by pressing the
button.
Parameter
Description
Low resolution.
Icon
AUTO
none
Scanned original setup
Standard resolution for
documents containing text and
graphics.
If you want, you can change the origin of the scanner.
TEXT
By entering new values for X and Y in mm (X < 209 and
Y < 280), you move the scanned area as shown on the
diagram below.
Optimal resolution for
documents containing
photographies.
PHOTO
QUALITY Optimal resolution for
TEXT documents containing text.
3 Confirm your choice by pressing the OK button.
4 Exit this menu by pressing the button.
ꢀ844 - ADVANCED FCT/COPY/ORIGIN
1 Press ꢀ, enter 844 using the keypad.
You can also change the resolution by
pressing the button.
Note
2 Select the X and Y coordinates with the buttons ꢁ
or ꢀ.
Zoom setup
3 Setup the desired coordinates with the numerical
keypad or the buttons ꢁand ꢀ.
The ZOOM parameter allows you to reduce or enlarge an
area of a document by choosing the origin and the zoom
level to apply to the document, from 25 to 400 %.
4 Confirm your choice by pressing the OK button.
5 Exit this menu by pressing the
button.
ꢀ842 - ADVANCED FCT/COPY/ZOOMING
Contrast setup
1 Press ꢀ, enter 842 using the keypad.
2 Enter the desired zoom level with the
alphanumerical keypad or choose among
predefined values with the buttons ꢁand ꢀ.
The CONTRAST parameter allows you to choose your
output’s contrast.
ꢀ845 - ADVANCED FCT/COPY/CONTRAST
3 Confirm your choice by pressing the OK button.
4 Exit this menu by pressing the
button.
1 Press ꢀ, enter 845 using the keypad.
2 Setup the desired level of contrast with the buttons
ꢁand ꢀ.
Collated copy setup
3 Confirm your choice by pressing the OK button.
The COLLATED parameter gives you the option of
4 Exit this menu by pressing the
button.
having your output collated or uncollated.
ꢀ843 - ADVANCED FCT/COPY/COLLATED
Brightness setup
1 Press ꢀ, enter 843 using the keypad.
The BRIGHTNESS parameter allows you to lighten or
darken your output.
2 Select the desired option with the buttons ꢁand ꢀ
according to the following table:
ꢀ846 - ADVANCED FCT/COPY/BRIGHTNESS
1 Press ꢀ, enter 846 using the keypad.
Parameter
Description
The printer assembles the copies of
the original document.
2 Setup the desired brightness with the buttons ꢁ
and ꢀ.
E.g.: Select collated for output
stacked in sets to match the
sequence of the originals, i.e. (1,2,3/
1,2,3).
COLLATED
3 Confirm your choice by pressing the OK button.
4 Exit this menu by pressing the
button.
The printer does not assemble the
copies of the original document.
UNCOLLATED
E.g.: Select uncollated for output
sorted into stacks of individual
pages, i.e. (1,1,1/2,2,2/3,3,3).
- 26 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
ꢀ854 - ADVANCED FCT/SCAN. & PRINT/
Paper type setup
FLATBED MARG
ꢀ851 - ADVANCED FCT/SCAN. & PRINT/PAPER
1 Press ꢀ, enter 854 using the keypad.
TYPE
2 Setup the left / right margins offsets (by 0.5 mm
steps) with the buttons ꢁand ꢀ.
1 Press ꢀ, enter 851 using the keypad.
3 Confirm by pressing the OK button.
2 Select NORMAL or THICK with the buttons ꢁ
and ꢀ.
4 Exit this menu by pressing the
button.
3 Confirm your choice by pressing the OK button.
4 Exit this menu by pressing the
button.
Left and right printing margin shift
If you want to, you can offset the lateral margins of the
document to the left or right during printing.
Paper tray selection
The Automatic selection can have two meanings
depending on the paper size defined for the paper trays.
The following table describes the different cases.
ꢀ855 - ADVANCED FCT/SCAN. & PRINT/
PRINTER MARG
1 Press ꢀ, enter 855 using the keypad.
2 Setup the left / right margins offsets (by 0.5 mm
steps) with the buttons ꢁand ꢀ.
Default tray
Tray used for copy
Selection between the
AUTOMATIC main tray and the
3 Confirm by pressing the OK button.
Same paper
size in the
trays
4 Exit this menu by pressing the
button.
manual tray.
The manual tray is
used.
Manual
Top and bottom printing margin shift
If you want to, you can offset the lateral margins of the
document towards the top or the bottom during printing.
AUTOMATIC The main tray is used.
Different
paper size in
the trays
The manual tray is
Manual
ꢀ856 - ADVANCED FCT/SCAN. & PRINT/TOP
used.
PRINT.
1 Press ꢀ, enter 856 using the keypad.
ꢀ852 - ADVANCED FCT/SCAN. & PRINT/TRAY
PAPER
2 Setup the top / bottom margins offsets (by 0.5 mm
steps) with the buttons ꢁand ꢀ.
1 Press ꢀ, enter 852 using the keypad.
3 Confirm by pressing the OK button.
2 Select the default paper tray to use, AUTOMATIC
or MANUAL, with the buttons ꢁand ꢀ.
4 Exit this menu by pressing the
button.
3 Confirm by pressing the OK button.
4 Exit this menu by pressing the
button.
Paper size setup
This menu allows you to define the default paper size of
the manual tray and the main tray. You can also setup the
default scanning width.
Margin Shift with the Automatic Document
Feeder
If you want to, you can offset the lateral margins of the
document to the left or right during the scanning from the
automatic document feeder.
ꢀ857 - ADVANCED FCT/SCAN. & PRINT/
PAPER FORMAT
1 Press ꢀ, enter 857 using the keypad.
2 Select the paper tray for which you want to define
a default paper size with the buttons ꢁand ꢀ.
ꢀ853 - ADVANCED FCT/SCAN. & PRINT/ S.F.
MARGINS
3 Confirm by pressing the OK button.
1 Press ꢀ, enter 853 using the keypad.
4 Choose the paper size with the buttons ꢁ or ꢀ
2 Setup the left / right margins offsets (by 0.5 mm
steps) with the buttons ꢁand ꢀ.
according to the following table:
Paper tray
Available paper size
3 Confirm by pressing the OK button.
4 Exit this menu by pressing the
button.
MAN. TRAY A5, Statement, A4, Legal and Letter
AUTO. TRAY A5, Statement, A4, Legal and Letter
Margin Shift using the Document Glass
SCANNER
LTR/LGL and A4
If you want to, you can offset the lateral margins of the
document to the left or right during the scanning from the
document glass.
5 Confirm by pressing the OK button.
6 Exit this menu by pressing the
button.
- 27 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Immediate transmission
Fax
1 Place the document to be copied face up in the
automatic document feeder.
This chapter describes all the fax processing and
configuration functions.
or
Place the document face down on the document
glass, aligned with the registration arrows near the
top left of the document glass.
You will also find a section describing fax mailboxes.
Fax transmission
2 Enter the fax number then press
or
.
3 If you are using the document glass, you can scan
more than one page. Place the next page on the
document glass, select NEXT and confirm with OK.
Select DONE when all pages have been scanned.
Print a cover sheet
A header page is stored in your machine. To send your
fax using this header page, you can print it at any time and
fill in your details.
The
icon flashes during the call phase, it stays lit
1 Select ꢀ30 - FAX /HEADER PAGE.
when both faxes are in communication.
2 Select:
At the end of transmission the initial screen is displayed.
301 - LOCAL, to print a header page according to
the language configured on the machine,
302 - INTERNAT, to print a bilingual header page,
the language of the country configured on the
machine and English. The separator between the
two languages is "/".
You can modify transmission options
when sending a fax. To do so, press
Note
OK after entering the fax number.
Delayed transmission
If English is the language configured
on the machine, the header page will
only be printed in English.
Note
This function allows you to transmit a document at a later
time.
To program a delayed transmission you need to identify
the subscriber number, transmission time, feeder type
and number of pages.
Example of the international header page:
To delay the transmission time of your document :
1 Place the document to be copied face up in the
automatic document feeder.
or
Place the document face down on the document
glass, aligned with the registration arrows near the
top left of the document glass.
Make sure that the document in the
ADF or on the document glass is
properly located in order to avoid
Important
sending blank or incorrect pages.
2 Select ꢀ31 - FAX / TRANSMISSION.
3 Enter the subscriber number or choose your
dialling mode and confirm with OK.
4 Next to the current time, enter the new time and
confirm with OK.
5 Adjust the contrast and confirm with OK.
6 Select the feed type, FEEDER or MEMORY and
confirm with OK.
7 You may enter the number of pages before
transmission and confirm with OK.
8 Confirm delayed transmission by pressing
.
9 If you are using the document glass, you can scan
more than one page. Place the next page on the
document glass, select NEXT and confirm with OK.
Select DONE when all pages have been scanned.
Your document is stored and will be sent at the new time.
- 28 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Default tray set to Manual:
Transmission with auto redial
This function allows you to monitor the dialling operation
during a fax transmission. In this case, the maximum
transmission rate will be 14400 bps.
Manual tray
paper size
Main tray
paper size
Action
A4,Letter and A4,Letter
Legal and Legal
The fax is printed from
the manual tray.
This function allows for example:
•
to hear if the subscriber’s fax is engaged and if so,
choose the moment when the line is clear to start the
document transmission.
A4,Letter and A5,
The fax is printed from
the manual tray.
Legal
Statement
The paper in the manual
tray is incompatible.
•
to control the communication progress in case of
uncertain numbers, etc.
A5,
Statement
A4,Letter
and Legal
The fax is printed from
the main tray.
To take the line manually:
1 Place the document in the automatic document
An error message is
displayed on the screen.
feeder.
A5,
Statement
A5,
Statement
2 Press
.
The paper in the manual
tray is incompatible.
3 If necessary, set the sound level using the ꢀor ꢁ
keys.
4 Enter the subscriber number.
Default tray set to Automatic:
As soon as you hear the remote fax tone, the line is
clear and you can start the transmission.
Manual tray
paper size
Main tray
paper size
Action
5 Press
to start the document transmission.
The fax is printed from
an automatic tray
selection.
A4,Letter and A4,Letter
Legal and Legal
If your machine is programmed to print a transmission
report, the reduced copy of the document first page will
not be printed and it notifies you that the communication
An error message is
displayed on the screen.
A4,Letter and A5,
Fax reception
The paper in the
automatic tray is
incompatible.
Legal
Statement
Fax reception depends on the parameter settings of your
machine.
A5,
Statement
A4,Letter
and Legal
The fax is printed from
the main tray.
The following parameters let you customize the printing of
received faxes:
An error message is
displayed on the screen.
A5,
Statement
A5,
Statement
The paper in the
automatic tray is
incompatible.
Relay broadcast
Your fax machine (initiator) can relay a document, in other
words, transmit a document to your subscribers via a
remote fax and with a precise relay list.
The printing of a fax is not
possible on A5 (or Statement)
paper size.
Important
To do this the initiator fax and the remote fax must both
have the relay function.
The following tables give which tray is used to print
received fax depending on the default tray and the paper
size in both trays.
To relay you need to supply the remote fax with the
document and the relay list number. The remote fax will
then transmit this document to all subscribers on the list.
Once the relay is activated by your fax and as soon as the
document is received by the remote fax, the document is
printed before relaying to all subscribers on the list.
- 29 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
To activate relay from your fax machine:
Activating / Deactivating the answering
machine
1 Load the document to be faxed.
ꢀ382 - FAX / FAX ANSW. / ACTIVATION
Make sure that the document in the
ADF or on the document glass is
properly loaded in order to avoid
sending blank or incorrect pages.
1 Press ꢀ, enter 382 using the keypad.
Important
2 If you saved an access code for your fax answering
machine, enter it and confirm with OK.
2 Select ꢀ37 - FAX / BROADCAST.
3 Select the required answering machine option, ON
or OFF, and confirm you choice with OK.
3 Enter the remote fax number where you will relay to
or choose your dialling mode and press OK.
4 Exit this menu by pressing the
button.
4 Enter the relay list number used by the remote fax
and press OK.
Printing fax messages stored in the memory
5 You may enter the time you wish to transmit the
document next to the current time and press OK.
Printing is not possible on A5 (or
Important
6 If you wish to modify the document feed type,
select one of the options FEEDER or MEMORY,
then press OK.
Statement) paper size.
ꢀ381 - FAX / FAX ANSW. / PRINT
7 If you wish, you may enter the number of pages of
your documents before transmitting.
1 Press ꢀ, enter 381 using the keypad.
2 If you saved an access code for your fax answering
machine, enter it and confirm with OK.
8 Activate relay by pressing
.
9 If you are using the document glass, you can scan
more than one page. Place the next page on the
document glass, select NEXT and confirm with OK.
Select DONE when all pages have been scanned.
Documents received and stored in the memory are
printed.
Fax rerouting
The document in the feeder will be relayed either
immediately or at a later time (according to your choice)
to the remote fax which will relay the document.
This function is used to reroute incoming faxes to a
directory contact. To use this function, you have to
perform two operations:
Fax answering machine
1 Activate rerouting.
The Fax answering machine allows you to keep
confidential documents in storage and to avoid printing
them as you receive them.
2 Set the rerouting address of the fax.
Activating rerouting
The
indicator light lets you know the state of your
Make sure that the subscriber exists
Fax answering machine:
Important
page 44).
•
•
Light on: the answering machine is on.
Blinking: your fax has documents in storage or is in the
process of receiving faxes.
ꢀ391 - FAX / REROUTING / ACTIVATION
•
Light off: memory full, the machine cannot receive any
more documents.
1 Press ꢀ, enter 391 using the keypad.
2 Using the keys ꢀand ꢁwithin the navigator,
select option ON.
You can assure document confidentiality by using the 4
digit access code. Once saved, you will require this
access code for:
3 Using the keys ꢀand ꢁwithin the navigator,
select the subscriber from the directory.
4 Confirm with OK.
•
•
printing fax messages in memory,
5 Exit this menu by pressing the
button.
activating or deactivating the fax answering machine.
If the option OFF is selected, the menus 392 and 393 will
not be included in the functions overview, when it is
printed out.
Saving an access code
ꢀ383 - FAX / FAX ANSW. / ANSWER CODE
1 Press ꢀ, enter 383 using the keypad.
2 Enter the code (4 digits) and confirm with OK.
3 Exit this menu by pressing the
button.
- 30 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Setting the re-direction contact
Printing rerouted documents
ꢀ392 - FAX / REROUTING / CALL NUMBER
Printing is not possible on A5 (or
Statement) paper format.
Important
Important
1 Press ꢀ, enter 392 using the keypad.
2 Using the keys ꢀand ꢁwithin the navigator,
This menu is only accessible when
the function FAX ARCHIVING is
activated.
select the subscriber from the directory.
3 Confirm with OK.
4 Exit this menu by pressing the
button.
ꢀ052 - MEDIA / FAX ARCHIVING / PRINT
Printing rerouted documents
1 Press ꢀ, enter 052 using the keypad.
ꢀ393 - FAX / REROUTING / COPY
2 Using the keys ꢀand ꢁ, select the option ON to
print all rerouted documents automatically.
1 Press ꢀ, enter 393 using the keypad.
3 Confirm your choice with OK.
2 Using the keys ꢀand ꢁwithin the navigator,
select the COPY option (local printout of the
information relayed to your device) either ON
or OFF.
4 Exit this menu by pressing the
button.
Transmission waiting queue
3 Confirm with OK.
This function lets you obtain a recap of all documents
queuing, for transmission, including those in deposit or in
delayed transmission, etc.
4 Exit this menu by pressing the
button.
Rerouting fax messages to a USB
memory key
It allows you to:
•
Consult or modify the waiting queue. In this waiting
queue the documents are coded the following way:
Order number in the queue / document status /
subscriber’s telephone number.
Documents may have the following status:
- TX: transmission
This function allows you to reroute received fax messages
directly in the folder Phaser3100MFP_X\FAX on a USB
memory key connected to your machine. The folder
Phaser3100MFP_X\FAX is created by the application.
The USB memory key then becomes the machine
reception memory.
- REL: relay
- DOC: in deposit
- POL: polling
- MBX: send to mailbox
- PMB: mailbox polling
- TR: ongoing commands
Fax messages that are rerouted are therefore saved on
the USB memory key with format Tiff and are named as
follows:
"FAXYYMMDDHHMMSS"
where
YYMMDDHHMMSS corresponds to the fax reception
date and time.
- SMS: SMS transmission
•
•
•
Immediately perform a transmission from the waiting
queue,
You can also print fax messages rerouted to your USB
memory key automatically by activating menu 052
PRINT.
Print a document in storage, waiting to be transmitted
or in deposit,
Print the waiting queue, in order to get the status of
each document in the queue, by either:
- queue order number,
Activating rerouting
- document name or number,
Before activating this function,
- scheduled transmission time (fax),
- operation type regarding the document: transmission
from memory, delayed transmission, deposit,
- number of pages of the document,
- document size (percentage of space stored in
memory)
connect the USB memory key to the
machine.
Important
ꢀ051 - MEDIA / FAX ARCHIVING / ACTIVATION
1 Press ꢀ, enter 051 using the keypad.
•
Cancel a transmission request in the waiting queue.
2 Using the keys ꢀand ꢁwithin the navigator,
select option ON and confirm your choice with OK.
Performing immediate transmission from
the waiting queue
3 Exit this menu by pressing the
button.
ꢀ61 - COMMANDS / PERFORM
1 Press ꢀ, enter 61 using the keypad.
2 Select the document in the waiting queue.
3 Confirm your choice with OK or
to
immediately perform the selected transmission.
- 31 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
MailBoxes (MBX Fax)
Consulting or modifying the waiting queue
ꢀ62 - COMMANDS / MODIFY
There are 32 mailboxes (MBX), enabling you to transmit
documents in complete confidence using an access code
(named MBX code), to all subscribers equipped with a fax
compatible to yours.
1 Press ꢀ, enter 62 using the keypad.
2 In the waiting queue select the required document
and confirm your choice with OK.
MBX 00 is public. It is handled directly by the machine to
record the messages of the fax TAD as soon as this is put
into service.
3 You may now modify the parameters of the given
document then confirm your modifications by
pressing
.
MBX’s 01 to 31 are private. Each is password-protected.
They can be used to receive documents confidentially.
Deleting a transmission on hold
The use and access to MBX 01-31 is dependent upon an
initialization, defined by an MBX code (if needed) and a
mnemonic (its S.I.D.).
ꢀ63 - COMMANDS / CANCEL
1 Press ꢀ, enter 63 using the keypad.
2 In the waiting queue select the desired document
and confirm your choice with OK.
Later you may:
•
•
modify the features of an MBX,
print the contents of an MBX, only possible if the MBX
contains one or more documents (with a star next to
the MBX). When the contents of an MBX have been
printed it becomes empty,
Printing a document in waiting or in deposit
ꢀ64 - COMMANDS / PRINT
1 Press ꢀ, enter 64 using the keypad.
•
•
delete an MBX, only if the MBX is initialised and
empty,
2 In the waiting queue select the desired document
and confirm your choice with OK.
print the list of your fax machine’s MBX’s.
You may receive and send through an MBX in complete
confidentiality.
Printing the waiting queue
ꢀ65 - COMMANDS / PRINT LIST
When depositing a document into your MBX, the access
code is not needed. All documents deposited in a MBX
are added to the ones already present.
Press ꢀ, enter 65 using the keypad.
You can also print the waiting queue with
Note
In polling, the MBX’s are only accessible with an MBX
code.
menu ꢀ57 - PRINT / COMMANDS.
A document called ** COMMAND LIST ** is printed.
You may perform MBX deposits or polls by:
•
•
depositing a document in a fax MBX,
Cancelling a transmission in
progress
transmitting to deposit a document in a remote fax
MBX,
•
performing document poll from a remote fax.
Cancelling a transmission in progress is possible no
matter what the type of transmission but varies depending
on whether the transmission is a single call number or a
multi-call number.
Creating an MBX
ꢀ71 - MAILBOXES / CREATE MBX
•
•
For a single call number from the memory, the
document is erased from the memory.
1 Press ꢀ, enter 71 using the keypad.
2 Select a free MBX out of the 31 MBX or directly
enter the number of a free MBX and confirm
with OK.
For a multi-call number, only the call number in
progress at the time of the cancellation is erased from
the transmission queue.
3 Select option MAILBOX CODE and press OK.
Value 0000 is always displayed.
To cancel transmission in progress:
4 Enter the code of your choice, if needed, and
press OK.
1 Press
.
5 Select option MAILBOX NAME and press OK.
A message will ask you to confirm cancellation.
6 Enter this MBX’s S.I.D. (20 characters max.) and
press OK.
2 Press
to confirm cancellation in progress.
The MBX is initialised. If you wish to initialise
another, press C and repeat the same procedure.
If your machine is set to print a transmission report, it will
print that the communication was cancelled by the user.
7 To exit the MBX, press
.
- 32 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Modifying the features of a MBX
MBX deposit in your fax
ꢀ71 - MAILBOXES / CREATE MBX
1 Insert the document in the automatic document
feeder.
1 Press ꢀ, enter 71 using the keypad.
2 Select ꢀ72 - MAILBOXES / DEPOSIT MBX.
2 Select the desired MBX out of the 31 MBX’s, or
enter the number of the MBX directly and
press OK.
3 Select the desired MBX out of the 31 MBX’s, or
enter the number of the MBX directly and
press OK.
3 Enter the code of this MBX, if there is one, and
confirm with OK.
The document is placed in the feeder and saved in the
selected MBX.
4 Select the menu MAILBOX CODE or MAILBOX
NAME, then confirm your choice with OK.
MBX deposit in a remote fax
5 Perform data modification of the menu and confirm
with OK.
1 Insert the document in the automatic document
feeder.
If needed, repeat the last two steps for the other menu.
2 Select ꢀ35 - FAX / MBX SENDING.
3 Enter your subscriber’s number for MBX deposit or
choose your dialling mode and validate with OK.
Printing the contents of a MBX
ꢀ73 - MAILBOXES / PRINT MBX
4 Enter the subscriber’s MBX number and confirm
with OK.
1 Press ꢀ, enter 73 using the keypad.
5 If you wish to delay transmission, enter the new
transmission time next to the current time and
press OK.
2 Select the desired MBX out of the 31 MBX’s, or
enter the number of the MBX directly and
press OK.
6 If you wish to modify the document feed type,
select one of the options FEEDER or MEMORY,
and press OK.
3 Enter the code of this MBX, if there is one, and
confirm with OK.
7 If you wish, you may enter the number of pages of
your document before transmitting and confirm
with OK.
All documents found in the MBX are printed and the MBX
is emptied.
8 Confirm the transmission request to a remote MBX
Deleting a MBX
fax by pressing
.
Before deleting an MBX, you need to make sure it is
empty, by printing its content.
In the case of an immediate transmission, the document
is sent immediately.
ꢀ74 - MAILBOXES / DELETE MBX
If the document is set for a delayed transmission, the
document will be stored in the memory and sent at the
requested time.
1 Press ꢀ, enter 74 using the keypad.
2 Select the desired MBX out of the 31 MBX’s, or
enter the number of the MBX directly and
press OK.
MBX polling from a remote fax
3 Enter the code of this MBX, if there is one, and
confirm with OK.
ꢀ36 - FAX / MBX POLLING
4 Press OK to confirm the MBX deletion.
Please check for remote fax
compatibility.
Note
The MBX is deleted and will appear as a free MBX in the
list.
1 Press ꢀ, enter 36 using the keypad.
Printing the MBX list
2 Enter your subscriber’s number for MBX polling or
choose your dialling mode and confirm with OK.
ꢀ75 - MAILBOXES / PRT MBX LIST
3 Enter the subscriber MBX number and press OK.
4 Enter this MBX access code and press OK.
Press ꢀ, enter 75 using the keypad.
5 If you wish to delay the poll time, enter the
departure time next to the current time and
press OK.
You can also print the MBX list with menu
ꢀ58 - PRINT / MBX LIST.
Note
6 Confirm the MBX poll request by pressing
.
The list gives the status of each MBX.
As soon as the remote fax is subscribed, either
immediately or later, the document(s) in the remote fax
MBX are received in your fax.
- 33 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Deposit and Polling
You may deposit a document in your fax and keep it
available to one or more subscribers who can obtain a fax
of this document by calling your fax with the POLL
function.
Setting the machine for document deposits, you must
define the type:
•
•
SIMPLE- it may be polled only once from the memory
or feeder,
MULTIPLE- it may be polled as many times as
necessary from the memory.
Setting the machine for polled documents, you must
define the poll number, then depending on the type of poll
you may:
•
•
•
launch an immediate poll,
program a delayed poll with a chosen time,
launch a multi-poll, either immediately or later.
Placing a document in deposit
1 Insert the document to deposit in the automatic
document feeder.
2 Select ꢀ34 - FAX / POLLING TX.
3 Choose the deposit type, according to the table
below:
Menu
Procedure
1 Select FEEDER or MEMORY.
2 If necessary, adjust the contrast
and confirm with OK.
Simple
3 Enter the number of pages that you
wish to deposit.
1 If necessary, adjust the contrast
and confirm with OK.
Multiple
2 Enter the number of pages that you
wish to deposit.
4 Confirm deposit by pressing OK.
Polling a deposited document
ꢀ33 - FAX / POLLING RX
1 Select ꢀ33 - FAX / POLLING RX.
2 Enter the number of the party whose document you
want to poll or choose your dialling mode.
You can poll several documents using the
key
.
3 Depending on the type of poll, you should:
Menu
Procedure
Immediate
poll
1 Press
.
1 Press OK.
2 Next to the current time, enter
Delayed poll
the time you wish to poll the
document and press
.
- 34 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Sending an SMS
SMS
1 Press the
key.
2 Write your SMS using the alphabetical keypad.
The SMS function is not available on
the US model.
To do so, an editor is at your disposal:
Important
•
•
for upper case letters, use the Ï key,
to move inside the data entry field, use ꢀ
and ꢁ,
Thanks to the SMS button, you can send an SMS to
subscribers all over the world. An SMS (Short Message
Service) is a service which permits short written
messages to be sent to mobile phones or other SMS-
compatible devices.
The number of characters you can send per message is
dependent upon the service provider and the country you
are sending your SMS from (e.g. France 160 characters,
Italy 640 characters).
•
to move in the text from one word to another,
press CTRL and one of the navigator keys (ꢀ
or ꢁ).
•
•
to go to the next line, use
,
to delete a character (by moving the cursor to
the left), use Í or C.
3 Confirm with OK.
4 Dial the number of the recipient (mobile phone or
any other SMS-compatible device) in one of the
following ways:
The SMS service is dependent upon the country and the
service provider.
•
•
dial the number using the numerical keypad,
enter the first letters of the recipient name,
There is a special scale of charges for
the SMS service.
Note
•
press the
key until the required name
appears (names are classified in alphabetical
order).
SMS Parameters
Your SMS may be sent to only one person or to
several people. To send an SMS:
Presentation of the sender
This setting allows you to show the name or the number
of the sender when sending an SMS.
•
•
to only one person, press OK to confirm.
to several people:
ꢀ41 - SMS SERVICE / SENDER
5 Press the
number.
key and enter the next recipient's
1 Press ꢀ, enter 41 using the keypad.
6 Repeat the operations as many times as required
(10 persons max.). Press OK to confirm the last
recipient; "SENDING SMS" is displayed as the
SMS is being sent.
2 Select the required presentation of the sender
option, ON or OFF, using the ꢀor ꢁkeys.
3 Confirm with OK.
SMS Center transmission number
•
•
If SMS appears, then the SMS has been put on hold
and a further attempt will take place a couple of
minutes later. To immediately execute or cancel
This setting allows you to enter the transmission number
for the SMS Server. Your Internet provider will provide
you with this number.
ꢀ421 - SMS SERVICE / INIT. SMS / SERVER
To check the SMS has been sent properly, you may
print the transmission/reception log (refer to paragraph
1 Press ꢀ, enter 421 using the keypad.
2 Enter the number of the transmission server using
the numerical keypad.
3 Confirm with OK.
- 35 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Automatic mode
Parameters/
Setup
ꢀ212 - SETUP / DATE/TIME / AUTO ADJUST
If you select OFF and confirm with OK, the summer /
winter time will not be changed automatically. For the
machine to be set to the new time, you will need to use the
211 MODIFY menu.
You can setup your machine as you like depending on the
use. In this chapter you will find descriptions of the
functions.
If you select ON and confirm with OK, you will not have to
care about any change at the end of March (+1h) and
October (-1h). You will just be informed of this change by
a message on the screen.
You can print the functions guide and the current setup of
your machine.
The default parameter is ON.
Your machine is continuously being
updated, new functions are regularly
made available.
Warning message
To
benefit,
visit
our
website
On automatic changing to summer / winter time, a
message will be displayed to inform you that the machine
time has been changed.
Note
update function available with the
Xerox Companion Suite software to
download the latest online updates
25-03-07 02:01
CHECK TIME
or
Date/Time
28-10-07 02:01
CHECK TIME
At any moment you may change the date and time on
your machine.
Depending on the country configured on the machine, the
date format is of type DDMMYY (e.g.: France) or
MMDDYY (e.g.: USA).
Your next action on the keypad will cause the message to
be automatically cleared.
Your fax number/Your name
ꢀ21 - SETUP / DATE/TIME
Your machine will print out your fax number and your
name on each document it transmits if you save these
settings.
1 Press ꢀ, enter 21 using the keypad. Confirm
with OK.
2 Enter the numbers of the required time and date
one after another (for example November 8 2004 at
9h33, press 0811040933 or 1108040933) and
press OK to confirm.
To benefit from this feature, you
must set SENDING HEADER to ON
(see
3 To exit this menu, press
.
The SENDING HEADER feature is
by default activated on the US
model and cannot be modified.
Summer time / Winter time setting
This menu lets you choose to change to summer / winter
time automatically or not.
To save your fax number and name:
ꢀ22 - SETUP / NUMBER/NAME
1 Press ꢀ, enter 22 using the keypad.
This function is only available if the
Important country configured on the machine is
part of the European Union.
2 Enter your fax number (20 digits max.) and
press OK to confirm.
The 21>DATE/TIME menu includes 2 submenus:
Manual mode
3 Enter your name (20 characters max) then press
OK to confirm.
ꢀ211 - SETUP / DATE/TIME / MODIFY
For example, if you want to type the letter C, press
the key C until it appears on the screen.
Your machine will prompt you to change the date and time
via the numerical keypad.
4 To exit this menu, press
.
- 36 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
To manually select the type of public telephone network:
Type of network
ꢀ202 - SETUP / GEOGRAPHICAL / NETWORK
You can connect your fax to either a PSTN or a private
network such as private automatic branch exchange
(PABX). You must select the network which is the most
convenient.
1 Press ꢀ, enter 202 using the keypad.
2 Select the required option and press the OK key to
confirm.
To select the type of network:
3 To exit this menu, press
.
ꢀ251 - SETUP / TEL. NETWORK / NETWORK TYPE
If none of the options in the list is
suitable, select the "OTHER" option.
1 Press ꢀ, enter 251 using the keypad.
Important
2 Select option PABX or PSTN then confirm your
choice with OK.
Language
3 To exit this menu, press
.
This setting enables you to choose the menu language of
your choice. By default, the machine is set to English.
If you are connecting your machine to a private network,
behind a company’s PABX, you may need to specify a
To select the language:
ꢀ203 - SETUP / GEOGRAPHICAL / LANGUAGE
Geographical settings
These settings will enable you to use your machine in
different preset countries using different languages.
1 Press ꢀ, enter 203 using the keypad.
2 Select the required language using ꢀand ꢁ, then
press the OK key to confirm.
Country
3 To exit this menu, press
.
By choosing a country, you initialise:
•
•
the settings for the public telephone network,
the language by default.
Local prefix
This function is used when your fax is connected to a
private network, behind a company’s PABX. It allows you
to program an additional automatic local prefix (to be
defined), enabling you to automatically exit the
company’s telephone network system, but only under
certain conditions:
To select the country:
ꢀ201 - SETUP / GEOGRAPHICAL / COUNTRY
1 Press ꢀ, enter 201 using the keypad.
2 Select the required option and press the OK key to
•
the company’s internal numbers, where a prefix is not
required, must be short numbers less than the
minimal size (to be defined, for example France has
10 digits),
confirm.
3 To exit this menu, press
.
•
the outside numbers requiring a prefix, must be long
numbers greater or equal to the minimal size (to be
defined, for example France has 10 digits).
If none of the options in the list is
suitable, select the "OTHER" option.
Important
Programming your fax with the local prefix consists of two
steps:
Telecommuncation Network
This setting enables you to manually set the type of public
telephone network (PSTN) for a country, so that your
machine can communicate over the public telephone
network in compliance with the applicable standards.
1 defining the minimal size (or equal) of the
company’s outside numbers,
2 defining the outgoing local prefix of the company’s
telephone network. This prefix will automatically be
added as soon as an external number is dialled.
By default, setting a country using the ꢀ201
command automatically sets the type of PSTN to use
in the selected country.
If you define a local prefix, do not
add it to the numbers stored in
These settings are different from the
NETWORK TYPE, which allows you
to choose between public and
private network.
Important the
directory,
it
will
be
Important
automatically dialled with each
number.
ꢀ252 - SETUP / TEL. NETWORK / PREFIX
1 Press ꢀ, enter 252 using the keypad.
- 37 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
2 Enter the required minimal SIZE NUMBER of the
company’s outside numbers and confirm with OK.
The minimal size will range between 1 and 30.
confirm your choice with OK.
In feeder mode, reduced images will not appear on
the transmission report.
3 Enter the required outgoing local PREFIX of the
company’s telephone network (maximum 10
characters) and confirm with OK.
3 To exit this menu, press
.
Economy period
To insert a pause for dial tone ("/" sign),
press simultaneously the CTRL and M
keys, or long press the 0 (zero) key on
the numerical keypad until the "/" sign
is displayed.
This function allows you to defer a fax transmission to "off-
peak hours" and thus reduce the cost of your
communications.
Note
The economy period, via the telephone network (at off-
peak hours), is preset by default from 7.00 pm to 7.30 am.
Nevertheless you may change this time slot.
4 To exit this menu, press
.
To modify the economy period:
Transmission report
ꢀ233 - SETUP / SEND / ECO PER.
You may print
a
transmission report for all
communications over the telephone network (PSTN).
1 Press ꢀ, enter 233 using the keypad.
2 Enter the hours of the new economy period (for
example 19:00-07:30) and confirm your choice
with OK.
You may choose between more than one criteria for
printing reports:
•
ON: a report is printed when the transmission is
successful or when it is cancelled (there is only one
report per request),
3 To exit this menu, press
.
To use the economy period:
•
OFF: no transmission report, however, your fax will
note all transmissions that took place in its log,
ꢀ32 - FAX / ECO TRANS.
•
•
ALWAYS: a report is printed with each transmission,
1 Select ꢀ32 - FAX / ECO TRANS.
ON ERROR: a report is printed only if the transmission
2 Enter the number of the fax recipient and confirm
with OK.
failed or is cancelled.
With each transmission report from memory, a reduced
version of the first page is automatically reproduced.
3 Adjust the contrast and confirm with OK.
4 Select the feed type, FEEDER or MEMORY and
confirm with OK.
To select the report type:
5 You may enter the number of pages before
transmission and confirm with OK.
ꢀ231 - SETUP / SEND / SEND REPORT
6 If you are using the document glass, you can scan
more than one page. Place the next page on the
glass, select NEXT and confirm with OK. Select
DONE when all pages have been scanned.
1 Press ꢀ, enter 231 using the keypad.
2 Select the required option ON, OFF, ALWAYS or
ON ERROR and confirm your choice with OK.
3 To exit this menu, press
.
Reception Mode
Document feed type
This function enables you, if you have an external device
(telephone, answering machine) plugged in to the EXT
socket on your machine, via USB or to the telephone plug
adapter, to select the device receiving faxes and/or voice
messages.
You may choose the way you want to feed your
documents:
•
from memory, transmission will take place only after
memory storage of the document and dialling.
It allows you to get your originals back quickly to free
up the machine.
You may choose between the following reception modes :
•
MANUAL : the machine does not receive any
documents automatically. When you answer your
telephone and realise that you are receiving a fax, you
•
from the feeder (automatic document feeder),
transmission will occur after dialling and paper
scanning. It allows transmission of larger documents.
should press the
receive the fax.
button on the machine to
To select the way you want to feed your documents:
•
•
FAX : the Fax reception mode is launched on the
machine systematically.
ꢀ232 - SETUP / SEND / MEMORY SEND.
FAX-ANSWER. : the machine handles reception of
fax messages automatically, the external device
handles reception of telephone communications
1 Press ꢀ, enter 232 using the keypad.
2 Select the option MEMORY or FEEDER and
- 38 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
automatically.
Press the #0 buttons on your telephone to cancel fax
detection.
2 Select the option WITH PAPER or WITHOUT
PAPER and confirm your choice with OK.
3 To exit this menu, press
.
•
FAX-TEL : the machine handles reception of fax
messages automatically, the DECT base (and
registered handsets) handles reception of telephone
communications automatically.
Press the #0 buttons on your telephone to cancel fax
detection.
Paper out is indicated by a beep and
a message on the screen.
Received faxes are then stored in
Important
memory (icon
flashing) to be
printed as soon as you load paper
into the paper tray.
To set the reception mode:
ꢀ241 - SETUP / RECEPTION / MODE
Number of copies
1 Press ꢀ, enter 241 using the keypad.
You may print incoming documents more than once (1 to
99).
2 Select the required option and confirm with OK.
3 To exit this menu, press
.
To set the number of each document received:
ꢀ243 - SETUP / RECEPTION / NBR OF COPIES
If you have connected a telephone to
the EXT socket on your machine or
to a telephone plug adaptor, we
recommend that you set the
reception mode to MANUAL.
1 Press ꢀ, enter 243 using the keypad.
2 Enter the desired number of copies and confirm
with OK.
3 To exit this menu, press
.
If you have connected a DECT base
to the USB port of your machine, we
recommend that you set the
reception mode to FAX-TEL.
At each document reception, your machine will print the
number of copies requested.
Important
Fax or PC reception
When you receive a call, you pick up
using this telephone and you hear
the particular fax tone. You can:
This menu, combined with a software program installed
on your PC will enable you to select the machine you wish
to receive the documents on:
- press the
button on your
•
•
•
fax,
machine or buttons #7 on your
telephone to receive the fax.
PC,
PC if available, fax otherwise.
ꢀ244 - SETUP / RECEPTION / PC RECEPT.
Reception without paper
For more details, please refer to Fax communications
Your machine offers you the possibility to either accept or
refuse document reception if your printer is unavailable
(no paper...).
Adjust to page
If your machine is unavailable, you may choose between
two modes of reception:
This menu allows you to print out received faxes
automatically adjusting them to the page size. Received
faxes are then automatically reduced or enlarged to fit the
page size which is used on the machine.
•
reception mode WITHOUT PAPER, your machine
saves the incoming messages in the memory,
•
reception mode WITH PAPER, your machine refuses
all incoming subscribers.
To turn adjust to page mode on:
To select the reception mode:
ꢀ242 - SETUP / RECEPTION / REC. PAPER
1 Press ꢀ, enter 242 using the keypad.
ꢀ245 - SETUP / RECEPTION / AUTO ADJUST.
1 Press ꢀ, enter 245 using the keypad.
2 Select the option ON or OFF and confirm with OK.
3 To exit this menu, press
.
- 39 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Received faxes reduction mode
This menu allows you to reduce received faxes for
printing. This adjustment can be automatic or manual.
Parameter
Description
1 - Scanning mode
Default value of the scan mode
resolution for the documents to be
transmitted.
Automatic mode:
This mode automatically resizes received faxes.
2 - TX header
Important: this parameter is by
default activated on the US model
and cannot be modified.
To set automatic mode:
ꢀ246 - SETUP / RECEPTION / REDUCTION
If this parameter is on, your header
will appear on all documents sent
to your subscribers with your
name, number, date and number
of pages.
1 Press ꢀ, enter 246 using the keypad.
2 Select AUTOMATIC and confirm with OK.
3 To exit this menu, press
.
Manual mode:
Warning: If you send a fax from
the automatic document feeder,
the transmission header will not
appear on the document your
correspondent receives.
The machine offers a 70 to 100 % reduction. Outside
these values, the machine beeps for an error. This fixed
reduction will be used when printing received faxes,
regardless of the size of the paper loaded in the tray.
3 - TX speed
Transmission speed for outgoing
documents.
To set the manual mode:
ꢀ246 - SETUP / RECEPTION / REDUCTION
For a quality telephone line
(compatible, no echo),
communications occur at
maximum speed.
1 Press ꢀ, enter 246 using the keypad.
2 Select FIXED and confirm with OK.
3 Enter the reduction value (between 70 and 100)
and confirm with OK.
However, it may be necessary to
restrict the transmission speed for
some calls.
4 To exit this menu, press
.
4 - Echo protect
6 - EPT mode
If this parameter is on, the on-line
echo will be reduced during long
distance calls.
Technical Parameters
As delivered your machine is preset by default. However,
you may adjust it to meet your requirements by resetting
the technical parameters.
For some long distance calls
(satellite), the on-line echo may
disturb the call.
To set the technical parameters:
7 - COM. display
8 - Eco energy
Choice between transmission
speed displayed or number of the
page in progress.
ꢀ29 - SETUP / TECHNICALS
1 Press ꢀ, enter 29 using the keypad.
Choosing the printer standby
delay: the printer will switch to
standby after a delay (in minutes)
of NON-operation or during the
period of time of your choice.
2 Select the desired parameter and confirm with OK.
3 With the keys ꢀ or ꢁ, modify the parameter
settings by following the table below and press OK.
Note: you can also access this
parameter by pressing the
key from the idle screen.
10 - RX header
If this parameter is on, all
documents received by your fax
will include the subscriber’s header
with his/her name, number (if
available) fax print date and the
page number.
- 40 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Printing the functions guide
Parameter
Description
11 - RX speed
Transmission speed for incoming
documents.
Printing is not possible on A5 (or
Statement) paper size.
Important
For a quality telephone line
(compatible, no echo),
communications occur at
maximum speed.
ꢀ51 - PRINT / FUNCTIONS LIST
Press ꢀ, enter 51 using the keypad.
However, it may be necessary to
restrict the transmission speed for
some calls.
The printing of the functions guide starts.
You can also access the PRINT menu
by pressing the button.
Note
12 - Rings
Number of rings to automatically
start your machine.
13 - Discard size
The Discard Size parameter only
defines the printing of received
faxes. The number of lines of a
document can be too high for the
paper size loaded. This parameter
defines the threshold beyond
which the extra lines are printed on
a second page. Below this
Printing the logs
Printing is not possible on A5 (or
Statement) paper size.
Important
The incoming and outgoing logs list the last 30
transmissions (incoming and outgoing) made by your
machine.
threshold, extras lines are deleted.
An automatic print out will take place after every 30
transmissions. However, you may request a print out at
any time.
If you choose ON, the threshold is
set on 3 centimeters.
If you choose OFF, the threshold is
set on 1 centimeter.
Each log (incoming or outgoing) contains a table with the
following information:
20 - E.C.M.
This parameter helps correct the
calls made on disturbed telephone
lines. It is used when the lines are
weak or too noisy. Transmission
times may be longer.
•
•
•
•
•
•
date and time of the incoming or outgoing document,
subscriber’s number or E-mail address,
transmission mode (Normal, Fine, SFine or Photo),
number of pages sent or received,
call duration,
25 - TEL Impedance
This parameter lets you choose
between a complex impedance
and a 600 Ohm impedance,
depending on the telephone
network your machine is
connected to.
incoming or outgoing results: noted CORRECT if
properly transmitted,
or
information codes for special calls (polling, manual
subscribers, etc.)
•
reason for call error (example: your subscriber does
not answer).
80 - Toner save
90 - RAW Port
Makes printing lighter to save toner
cartridge ink.
To print the logs:
RAW network print port
connection.
ꢀ54 - PRINT / LOGS
91 - Printer error
timeout
Time-out before document being
printed is deleted following a print
error in PC print mode.
Press ꢀ, enter 54 using the keypad.
The printing of the logs starts. The incoming and outgoing
logs are printed on the same page.
92 - Printer wait
timeout
Wait time-out for data from PC
before the task is deleted in PC
print.
You can also access the PRINT menu
Note
by pressing the
button.
93 - Replace format
Page size change. This parameter
allows you to print a LETTER size
document on A4 pages using the
LETTER/A4 setting.
96 - NBR. WEP
Keys
Number of WEP keys allowed
(from 1 to 4).
- 41 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
2 Enter the four-digit access code using the keypad.
3 Press OK to confirm.
Print the list of setups
4 With the buttons ꢀ or ꢁ, choose DIRECT ONLY
and confirm with OK.
Printing is not possible on A5 (or
Statement) paper size.
Important
5 Exit this menu by pressing the
button.
To print the list of setups:
ꢀ56 - PRINT / SETUP
Lock the SMS service
This function prevents access to the SMS service.
To access the SMS service locking menu:
Press ꢀ, enter 56 using the keypad.
The printing of the list of setups starts.
ꢀ815 - ADVANCED FCT / LOCK / LOCK SMS
You can also access the PRINT menu
by pressing the button.
Note
1 Press ꢀ, enter 815 using the keypad.
2 Enter the four-digit access code using the keypad.
3 Press OK to confirm.
Lock the machine
4 With the buttons ꢀ or ꢁ, choose ON and confirm
with OK.
This function prevents non-authorized people from
accessing the machine. An access code will be required
every time someone wants to use the device. After each
use, the device will lock automatically.
5 Exit this menu by pressing the
button.
Lock the Media service
This function prevents access to the Media service. The
access code will be required every time someone wants
to use the USB key functions:
Before that you have to enter an access code.
ꢀ811 - ADVANCED FCT / LOCK / LOCKING CODE
•
•
•
view the contents of a connected USB key,
print from a USB key, delete files,
1 Press ꢀ, enter 811 using the keypad.
2 Enter your access code (4 digits) using the keypad,
confirm with OK.
archive received faxes on a USB key.
To access the Media service locking menu:
If a code is already in existence,
Important enter the old code before typing the
new one.
ꢀ816 - ADVANCED FCT / LOCK / LOCK MEDIA
1 Press ꢀ, enter 816 using the keypad.
2 Enter the four-digit access code using the keypad.
3 Press OK to confirm.
3 Enter again your access code (4 digits) using the
keypad, confirm with OK.
4 Exit this menu by pressing the
button.
4 With the buttons ꢀ or ꢁ, choose ON and confirm
with OK.
Lock the keyboard
5 Exit this menu by pressing the
button.
Every time you use your machine, you will have to enter
your code.
Read the counters
ꢀ812 - ADVANCED FCT / LOCK / LOCK KEYBD.
This function allows you to view the activity counters for
your machine at any time.
1 Press ꢀ, enter 812 using the keypad.
2 Enter the four-digit access code using the keypad.
3 Press OK to confirm.
According to your needs, you can read the counters for:
•
•
•
•
sent pages,
4 With the buttons ꢀ or ꢁ, choose ON and confirm
with OK.
received pages,
scanned pages,
printed pages.
5 Exit this menu by pressing the
button.
Lock the numbers
Sent pages counter
This function locks dialling and the numerical keypad is
disabled. Transmissions are only possible from numbers
included in the directory.
To view the number of pages sent from your machine:
ꢀ821 - ADVANCED FCT / COUNTERS / SENT PAGES
To access the numerical keypad locking menu:
1 Press ꢀ, enter 821 using the keypad.
ꢀ813 - ADVANCED FCT / LOCK / LOCK NUMBER
2 The number of sent pages appears on the screen.
1 Press ꢀ, enter 813 using the keypad.
3 Exit this menu by pressing the
button.
- 42 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Received pages counter
To view the number of pages received on your machine:
ꢀ822 - ADVANCED FCT / COUNTERS / RECEIVED
PG
1 Press ꢀ, enter 822 using the keypad.
2 The number of received pages appears on the
screen.
3 Exit this menu by pressing the
button.
Scanned pages counter
To view the number of pages scanned on your machine:
ꢀ823 - ADVANCED FCT / COUNTERS / SCANNED
PAGE
1 Press ꢀ, enter 823 using the keypad.
2 The number of scanned pages appears on the
screen.
3 Exit this menu by pressing the
button.
Printed pages counter
To view the number of pages printed on your machine:
ꢀ824 - ADVANCED FCT / COUNTERS / PRINTED PG
1 Press ꢀ, enter 824 using the keypad.
2 The number of printed pages appears on the
screen.
3 Exit this menu by pressing the
button.
Display the consumables status
You can read at any time the remaining toner in the
cartridge. This level appears in percentage.
ꢀ86 - ADVANCED FCT / CONSUMABLES
1 Press ꢀ, enter 86 using the keypad.
2 The available toner percentage appears on the
screen.
3 Exit this menu by pressing the
button.
Calibrate your scanner
You can do this operation when the quality of photocopied
documents is not satisfactory anymore.
ꢀ80 - ADVANCED FCT / CALIBRATION
1 Press ꢀ, enter 80 using the keypad. Confirm
with OK.
2 The scanner is triggered and a calibration is done
automatically.
3 At the end of the calibration, the machine comes
back up in the screen saver mode.
- 43 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Creating subscribers list
Directory
To create subscribers list:
ꢀ12 - DIRECTORY / NEW GROUP
Your multifunction machine lets you create a directory by
memorising subscriber records and subscriber lists. Your
machine can store up to 250 subscriber records, which
you can group in 20 subscriber lists.
1 Press ꢀ, enter 12 using the keypad.
2 Enter the LIST NAME with the alphanumerical
keypad (20 characters maximum), confirm
with OK.
For all subscriber records or subscriber lists you may
create, consult, modify or delete contents. You can also
print the directory.
3 CALLED NUMBER: use ꢀor ꢁto select from
existing records the contacts of your list and
confirm with OK. Repeat this operation for each
subscriber you want to add to your list.
Furthermore, your machine lets you create and manage
your phone directory from your PC Kit. For more
4 Enter the GROUP NUMBER assigned to your list
with the numerical keypad or accept the displayed
number, and confirm with OK.
Creating subscribers record
To create subscribers record:
In the directory, the letter G placed
next to a name identifies a
subscribers group.
Important
ꢀ11 - DIRECTORY / NEW CONTACT
1 Press ꢀ, enter 11 using the keypad.
2 Enter the NAME of your contact with the
alphanumerical keypad (20 characters maximum),
confirm with OK.
Modifying a record
To modify a subscribers record or list:
3 Enter the TEL number of your contact with the
numerical keypad (30 digits maximum), confirm
with OK.
ꢀ13 - DIRECTORY / MODIFY
1 Press ꢀ, enter 13 using the keypad.
4 Choose the RECORD NO from your directory with
the numerical keypad or accept the displayed
number, and confirm with OK.
2 With ꢀor ꢁ, browse the directory and select the
record or list you want to modify by pressing OK.
3 With ꢀor ꢁ, browse the entries of the selected
record or list. Press OK when the entry you want to
modify appears on screen.
5 Select W. ASSOC. KEY if you want to assign a
shortcut key (letter) to your subscriber record. The
first available letter appears, use ꢀor ꢁto choose
another letter. Confirm with OK.
4 The cursor appears at the end of the line. Press C
to delete characters.
6 Select the appropriate transmission RATE to send
faxes among the values 2400, 4800, 7200, 9600,
12000, 14400 and 33600 using ꢀor ꢁ. Confirm
with OK.
5 Enter the new entry and confirm with OK.
6 Repeat the operations for each line you want to
modify.
The maximum speed can be used if the telephone
line is of good quality, meaning appropriate,
without echo.
Deleting a record or a list
To delete a subscribers record or list:
ꢀ14 - DIRECTORY / CANCEL
If your multifunction machine is
connected to a PABX, you may
insert a pause for dial tone after the
outgoing local prefix dialling.
1 Press ꢀ, enter 14 using the keypad.
2 With ꢀor ꢁ, browse the directory and select the
record or list you want to delete by pressing OK.
To insert a pause for dial tone ("/"
3 Press OK to confirm the deletion.
sign), press simultaneously the
CTRL and M keys, or long press the
0 (zero) key on the numerical
Important
4 Repeat the operations for each record or list you
want to delete.
keypad until the "/" sign is displayed.
For more details, refer to Local
- 44 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Printing the directory
Printing is not possible on A5 (or
Statement) paper size.
Important
To print the directory:
ꢀ15 - DIRECTORY / PRINT
Press ꢀ, enter 15 using the keypad.
The printing of the directory starts, in alphabetical order.
You can also print the directory with
Note
menu ꢀ55 - PRINT / DIRECTORY.
Saving/Restoring the directory
(Smart card option)
This function enables you to save the contents of your
directory on a Smart card and restore them on your
machine.
This function is only available to a
service technician with a Smart
card.
Important
To save the contents of your directory on your Smart
card:
ꢀ161 - DIRECTORY / SAVE/LOAD / SAVE
1 Press ꢀ, enter 16 using the keypad.
2 Select SAVE to save directory entries on the Smart
card and confirm with OK.
3 Insert your Smart card.
To restore the contents of your directory from your Smart
card:
ꢀ162 - DIRECTORY / SAVE/LOAD / LOAD
1 Press ꢀ, enter 16 using the keypad.
2 Select LOAD to restore directory entries from the
Smart card and confirm with OK.
3 Confirm with OK.
4 Insert your Smart card.
- 45 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
3 Confirm with OK.
Games and
Calendar
Sudoku
4 Select PRT SOLUTION using the ꢀor ꢁbutton.
5 Select the level of difficulty EASY, MEDIUM,
HARD, EVIL using the ꢀor ꢁbutton.
6 Confirm with OK.
7 Choose the grid you want by entering the number
on the numeric keypad (1 to 100).
8 Confirm with OK.
9 Choose the number of copies you want by entering
Sudoku is a Japanese puzzle. The game is in a grid
format of three squares by three squares to be distributed
in fields in zones of 3 × 3. Depending on the level of
difficulty, more or fewer numbers are already entered at
the start of the game. The aim of the game is to distribute
the numbers 1 to 9 between the boxes in such a way that
each number appears only once in each row, column and
in each of the nine grids. There is only one solution.
a number from 1 to 9 on the numeric keypad.
10 Confirm with OK.
The number of copies of the solution to the grid requested
is printed.
Calendar
This function enables you to print the calendar for a year
of your choice.
Print a grid
There are 400 Sudoku grids available in total, 100 for
each difficulty level.
Printing is not possible on A5 (or
Important
Statement) paper size.
Printing is not possible on A5 (or
Important
Statement) paper size.
ꢀ 53 - PRINT / CALENDAR
ꢀ 521 - PRINT / SUDOKU / PRINT GRID
1 Press ꢀ, enter 5 using the keypad. Confirm
with OK.
1 Press ꢀ, enter 5 using the keypad. Confirm
with OK.
You can also access the PRINT menu
Note
You can also access the PRINT menu
by pressing the
button.
Note
by pressing the
button.
2 Select CALENDAR using the ꢀor ꢁbutton.
3 Confirm with OK.
2 Select SUDOKU using the ꢀor ꢁ button.
3 Confirm with OK.
4 Choose the year you want to print as calendar by
entering the number on the numeric keypad (for
example: 2009).
4 Select PRINT GRID using the ꢀor ꢁ button.
5 Select the level of difficulty EASY, MEDIUM,
HARD, EVIL using the ꢀor ꢁbutton.
The year must be between 1900 and
6 Confirm with OK.
2099. Use the C key to correct an
Note
7 Choose the grid you want by entering the number
entry.
on the numeric keypad (1 to 100).
5 Confirm with OK.
8 Confirm with OK.
The calendar of the year requested is printed.
9 Choose the number of copies you want by entering
a number from 1 to 9 on the numeric keypad.
10 Confirm with OK.
The number of copies of the grid requested is printed.
Print the solution to a grid
Printing is not possible on A5 (or
Important
Statement) paper size.
ꢀ 522 - PRINT / SUDOKU / PRT SOLUTION
1 Press ꢀ, enter 5 using the keypad. Confirm
with OK.
You can also access the PRINT menu
Note
by pressing the
button.
2 Select SUDOKU using the ꢀor ꢁbutton.
- 46 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
The speed of communication across the whole radio
network is as fast as the weakest connection in the
network. The speed of communication is also dependent
Network features
You may connect your multifunction machine to a on spatial distance between transmitter and receiver, as
wireless network.
well as the number of barriers, such as walls or ceilings.
However, practical knowledge of your computer
configuration is required to set up a network.
Please note that in ad-hoc mode,
the WPA/WPA2 encryption method
is not available.
Important
You can connect your machine to a PC using a USB cable
or make a wireless connection (via radio) with a PC or
network.
If you have a WLAN adaptor, you
can incorporate your machine as a
network printer into a radio network.
This works only with an approved
adaptor that you can obtain from our
Important
ordering department. For further
information, contact
Type of radio network
A radio network or WLAN (Wireless Local Area Network)
is created when at least two computers, printers or other
peripheral devices communicate with each other in a
network via radio waves (high frequency waves). The
transmission of data in the radio network is based on the
standards 802.11b and 802.11g. According to how the
network is set up, it may be described as an infrastructure
network or an ad-hoc network.
Radio networks (WLAN)
Three steps are necessary to incorporate your machine
into a radio network (WLAN):
1 Configure the network to your PC.
Please note, when you are using a
wireless connection, that certain
items of medical equipment,
2 Set up the parameters for your machine so that it
can function in a network.
3 Having set up the parameters for your device,
install the Xerox Companion Suite software onto
your PC with the necessary printer drivers.
sensitive or security systems may
be affected by the radio
CAUTION
transmissions of your device; in all
cases, please follow safety
guidelines closely.
Once the machine is incorporated into a WLAN network,
you can from your PC:
•
print documents on the multifunction machine from
your usual applications,
Radio infrastructure network
•
scan colour, grey scale or black and white documents
on your PC.
In an infrastructure network, several devices
communicate via a central access point (a gateway or
router). All data is sent to the access point (gateway or
router) from where it is re-distributed.
The PC and all other devices must
have their parameters set up to the
same network as the multifunction
machine. All the details needed for
setting up the device, such as the
network names (SSID), type of radio
network, encryption key, IP address
or subnetwork mask, must match
the specifications of the network.
Important
You will find these details on your
PC or on the Access Point.
To find out how to set up the
parameters for your PC, please
consult the users’ manual for your
WLAN adaptor. For large networks,
please seek the advice of your
network administrator.
Radio ad-hoc network
In an ad-hoc network, the devices communicate directly
with each other without passing through an access point.
- 47 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Configure your network
You can be sure of perfect
communication if you use an
approved adaptor in conjunction with
your PC.
We recommend that the settings of
your WLAN network should only be
changed by a person with a good
knowledge of the configuration of your
computer.
Note
Note
All of the latest printer drivers for the
approved adaptor may be found on
our website together with further
Creating or rejoining a network
Connect your WLAN adaptor
Before attempting to use a WLAN adaptor on your
machine, you must enter the parameters that will allow a
WLAN network to recognise your machine.
Your machine belongs to a new generation of terminals
that you can incorporate into a WLAN network using a
WLAN USB key.
On your machine you will find simple instructions
that guide you step by step through the set-up of your
network. Just follow them!
Your machine’s network radio
adaptor transmits data using the
radio protocol IEEE 802.11g; it can
also be incorporated into an existing
IEEE 802.11b network.
ꢀ281 - SETUP / WLAN / CONFIG. ASS.
1 Press ꢀ, select the menu SETUP using the keys
ꢀor ꢁand confirm with OK.
2 Select WLAN using the keys ꢀor ꢁand confirm
with OK.
When connecting to your machine,
only use the approved adaptor.
Other transmitting or receiving
3 Select CONFIG. ASS. using the keys ꢀor ꢁand
confirm with OK.
adaptors may damage your device.
Important
The machine searches for existing networks.
Irrespective of whether you use your
machine in an infrastructure or ad-
hoc network, you must set up certain
network and security parameters
(for example, the Service-Set-ID
(SSID) and the encryption key).
These must match the network’s
specifications.
4 Select your existing network, or select NEW
NETWORK to create it, using the keys ꢀor ꢁand
confirm with OK.
If you choose an existing network,
steps 5 and 6 (and possibly 7) are
carried out automatically.
Note
5 SSID appears on the screen, enter the name of
your network using the numerical keypad, pressing
the keys one after the other until you obtain the
name you want (32 characters maximum) and
confirm with OK.
1 Plug your WLAN USB key into the USB port of your
machine.
6 AD-HOC MODE or INFRA. MODE appear on the
screen. Go back to the beginning of the chapter
and make your choice.
Select one of these modes and confirm with OK.
-
If you choose AD-HOC mode, the sub-menu
CHANNEL appears, enter a figure between 1
and 13 and confirm with OK.
7 Select your encryption method, OFF, WEP or
WPA, and confirm with OK:
Please note that in ad-hoc mode,
the WPA/WPA2 encryption method
is not available.
Important
-
If you choose WEP, enter the WEP key that you
are using on your network.
The WEP key number may be
configured in the menu: ꢀ29 -
SETUP / TECHNICALS / WEP KEYS
Note
NBR.
-
If you choose WPA, enter the WPA or WPA2
key that you are using on your network.
- 48 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
8 IP CONF.: MANU or IP CONF.: AUTO appear on
the screen.
confirm with OK.
4 Select GATEWAY using the keys ꢀor ꢁand
confirm with OK.
If you choose to set up the system manually, go to
the next paragraph and enter the parameters
IP ADDRESS, SUBNET MASK and GATEWAY.
5 The number of your gateway will appear in the
format 000.000.000.000. Enter the new gateway
for your machine in the format displayed and
confirm with OK.
9 At the end of this procedure, you return to the main
menu of CONFIG. ASS.
10 Exit this menu by pressing the
key.
6 Exit this menu by pressing the
key.
Once the network has been set up, the LED of the WLAN
USB key should be on.
ꢀ2825 - SETUP /WLAN / PARAMETERS / SSID
1 Press ꢀ, select the menu SETUP using the keys
ꢀor ꢁand confirm with OK.
Referring to or changing your
network parameters
2 Select WLAN using the keys ꢀor ꢁand confirm
with OK.
Each of the parameters of your network may be changed
as your network develops.
3 Select PARAMETERS using the keys ꢀor ꢁand
confirm with OK.
ꢀ2822 - SETUP / WLAN / PARAMETERS / IP
4 Select SSID using the keys ꢀor ꢁand confirm
with OK.
ADDRESS
5 The name of your network will appear on the
screen. Enter the new name of your network and
confirm with OK.
1 Press ꢀ, select the menu SETUP using the keys
ꢀor ꢁand confirm with OK.
2 Select WLAN using the keys ꢀor ꢁand confirm
with OK.
6 Exit this menu by pressing the
key.
3 Select PARAMETERS using the keys ꢀor ꢁand
confirm with OK.
ꢀ2826 - SETUP / WLAN / PARAMETERS / MODE
4 Select IP ADDRESS using the keys ꢀor ꢁand
confirm with OK.
1 Press ꢀ, select the menu SETUP using the keys
ꢀor ꢁand confirm with OK.
5 The number of your IP address will appear in the
format 000.000.000.000. Enter the new IP address
for your machine in the format displayed and
confirm with OK.
2 Select WLAN using the keys ꢀor ꢁand confirm
with OK.
3 Select PARAMETERS using the keys ꢀor ꢁand
confirm with OK.
6 Exit this menu by pressing the
key.
4 Select MODE using the keys ꢀor ꢁand confirm
with OK.
ꢀ2823 - SETUP / WLAN / PARAMETERS / SUBNET
5 The symbol >>, tells you that your network is in
MASK
active mode.
6 Select one of the modes and confirm with OK.
1 Press ꢀ, select the menu SETUP using the keys
ꢀor ꢁand confirm with OK.
-
If you choose the AD-HOC MODE, the sub-
menu CHANNEL will appear; enter a number
between 1 and 13 and confirm with OK.
2 Select WLAN using the keys ꢀor ꢁand confirm
with OK.
3 Select PARAMETERS using the keys ꢀor ꢁand
confirm with OK.
7 Exit this menu by pressing the
key.
4 Select SUBNET MASK using the keys ꢀor ꢁand
confirm with OK.
In an AD-HOC network, the devices
communicate directly with each
other without passing through an
access point. The speed of
communication across the whole
AD-HOC radio network is as fast as
the weakest connection in the
network. The speed of
5 The number of your subnet mask will appear in the
format 000.000.000.000. Enter the new submask
of your machine in the format displayed and
confirm with OK.
Important
6 Exit this menu by pressing the
key.
communication is also dependent on
spatial distance between transmitter
and receiver, as well as the number
of barriers, such as walls or ceilings.
ꢀ2824 - SETUP / WLAN / PARAMETERS / GATEWAY
1 Press ꢀ, select the menu SETUP using the keys
ꢀor ꢁand confirm with OK.
2 Select WLAN using the keys ꢀor ꢁand confirm
with OK.
3 Select PARAMETERS using the keys ꢀor ꢁand
- 49 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
ꢀ2827 - SETUP / WLAN / PARAMETERS / SECURITY Once your connection has been set up, you must install
the network printer driver on your PC so that you can print
This parameter allows you to make your network secure your documents.
by setting the encryption method to use in your WLAN Refer to the paragraph Software installation, page 57.
network.
An example of how an AD-HOC network
1 Press ꢀ, select the menu SETUP using the keys
may be set up
ꢀor ꢁand confirm with OK.
Below is an example of how to configure an Ad-hoc
network without security protection using the following
parameters:
2 Select WLAN using the keys ꢀor ꢁand confirm
with OK.
3 Select PARAMETERS using the keys ꢀor ꢁand
confirm with OK.
•
•
•
•
•
•
•
•
network name: "house"
4 Select SECURITY using the keys ꢀor ꢁand
confirm with OK.
radio type: "ad-hoc"
channel: "1"
5 Choose WEP, WPA or OFF and confirm with OK.
PC’s IP address: "169.254.0.1"
PC’s subnetwork mask: "255.255.0.0"
PC’s gateway: "0.0.0.0"
-
If you choose WEP, enter a password:
- In a 64 bit security configuration, the password
must contain five characters exactly.
- In a 128 bit security configuration, the
password must contain 13 characters exactly.
IP address of the multifunction machine: "169.254.0.2"
subnetwork mask of the multifunction machine:
"255.255.0.0"
You may also enter the password
using the hexadecimal system, if this
is the case:
•
multifunction machine’s gateway: "0.0.0.0"
- For a 64 bit security configuration,
the password must contain exactly
10 hexadecimal characters.
Setting up a machine
Note
1 Plug the WLAN USB key into the USB connector of
- For a 128 bit security configuration,
the password must contain exactly
26 hexadecimal characters.
the multifunction machine.
2 Press ꢀ, select the menu SETUP using the keys
ꢀor ꢁand confirm with OK.
3 Select WLAN using the keys ꢀor ꢁand confirm
with OK.
-
If you choose WPA, enter a WPA or WPA2
password (min. 8 characters to 63 characters
max.).
The password can contain alphanumerical
characters - numbers and letters - and any other
symbol available on the keypad. The only
invalid character is "€" (euro currency sign).
4 Select CONFIG. ASS. using the keys ꢀor ꢁand
confirm with OK.
5 Select NEW NETWORK using the keys ꢀor ꢁ
and confirm with OK.
6 SSID appears on the screen, enter "house" using
the numerical keypad and confirm with OK.
6 Exit this menu by pressing the
key.
7 Select the mode AD-HOC MODE and confirm
with OK.
8 Enter "1" in the field CHANNEL and confirm
with OK.
ꢀ2828 - SETUP / WLAN / PARAMETERS /
HOSTNAME
9 Select OFF and confirm with OK.
10 Select IP CONF.: MANU and confirm with OK.
The machine name allows you to identify your machine on
the network via a PC (for example with the name "PRINT-
NETWORK-1").
11 Enter "169.254.0.2" in the field IP ADDRESS and
confirm with OK.
12 Enter "255.255.0.0" in the field SUBNET MASK
and confirm with OK.
1 Press ꢀ, select the menu SETUP using the keys
ꢀor ꢁand confirm with OK.
13 Enter "0.0.0.0" in the field GATEWAY and confirm
with OK.
2 Select WLAN using the keys ꢀor ꢁand confirm
with OK.
14 At the end of this process, you return to the main
menu of ASS. CONFIG.
3 Select PARAMETERS using the keys ꢀor ꢁand
confirm with OK.
15 Exit this menu by pressing the
key.
4 Select HOSTNAME using the keys ꢀor ꢁand
confirm with OK.
Once the network has been set up, the LED of the WLAN
USB key should be on.
5 Type in the desired name (15 characters
maximum) and confirm with OK.
You must now set up the PC.
6 Exit this menu by pressing the
key.
- 50 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Setting up the PC
For this section, refer to the instructions supplied by the
manufacturer of the WLAN USB key to help you to find
and join the "house" network.
1 You may need to install the software for the WLAN
USB key on the PC, if this has not already been
done.
2 Plug WLAN USB key into a USB port on the PC.
3 Use the software of the WLAN USB key to detect
the network.
4 Join the network "house" once this has been
detected.
5 Now set up the WLAN network connection of your
PC.
To guide you through this stage, refer
to the paragraph “Setting the
parameters for a connection” in the
Note
manufacturer’s instructions.
To do this, you must configure the element
Protocol Internet (TCP/IP) for the WLAN
connection that has been created. If this element is
set up in such a way as to obtain an IP address
automatically, you must change it to manual mode
to set up the TCP/IP address ("169.254.0.1" in our
example), the subnet mask ("255.255.0.0" in our
example) and the default gateway ("0.0.0.0" in our
example).
6 Enter OK.
- 51 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
4 The list is shown in a table with the following
information:
USB memory key
-
the scanned files are indexed in an incremental
1 by 1 order,
You can connect a USB memory Key in the front of your
machine. The files stored in TXT, TIFF and JPEG formats
will be read and you will be able to perform the following
actions:
-
-
-
the files name with their extension,
the date of the files last save,
the files size in Kbytes.
- print the stored files contained in your USB memory
1
key ,
Print the files stored on the key
- delete the files contained in your USB memory key,
- query the contents of the inserted USB memory key,
- scan a document on your USB memory key,
To print the files stored on the key:
ꢀ01 - MEDIA / PRINT DOC. / FILE
1 Insert the USB memory key into the front of the
machine.
Use of the USB memory key
MEDIA ANALYSIS appears on the screen.
2 Select PRINT DOC. with the ꢀor ꢁbuttons and
confirm with OK.
Always take care when you insert a
USB memory key into the machine.
Do not disconnect your USB memory
key while the machine is reading its
contents or writing contents.
3 Select FILE with the ꢀor ꢁbuttons and confirm
with OK.
Important
4 You have three possible ways to print your files:
-
ALL, to print all the files stored on the USB
memory key.
Select ALL with the ꢀor ꢁbuttons and
confirm with OK. The printing is started
automatically.
-
SERIES, to print a series of files stored on the
USB memory key.
Select SERIES with the ꢀor ꢁbuttons and
confirm with OK.
FIRST FILE and the first indexed file appears
on the screen. Select with the ꢀor ꢁbuttons
the first file of the series to print and confirm
with OK. A star (*) appears on the left side of the
file.
LAST FILE appears on the screen. Select with
the ꢀor ꢁbuttons the last file of the series to
print and confirm with OK.
Press the
button.
Print your documents
COPIES NUMBER appears on the screen,
enter the desired number of copies with the
numerical keypad and confirm with OK.
Select the printing format (for JPEG files): A4 or
LETTER (depending on model), or PHOTO and
confirm with OK.
Printing is not possible on A5 (or
Statement) paper size.
Important
You can print the stored files or a list of the files located in
the USB memory key.
Select the printing format: THICK or NORMAL
and confirm with OK to start printing.
Print the list of files located in the key
-
SELECTION, to print one or several files stored
on the USB memory key.
To print the list of files located in the key:
ꢀ01 - MEDIA / PRINT DOC. / LIST
Select with the ꢀor ꢁbuttons the file to print
and confirm with OK. A star (*) appears on the
left side of the file.
1 Insert the USB memory key into the front of the
machine.
Repeat this step for each file you want to print.
MEDIA ANALYSIS appears on the screen.
Press the
button.
2 Select PRINT DOC. with the ꢀor ꢁbuttons and
confirm with OK.
COPIES NUMBER appears on the screen,
enter the desired number of copies with the
numerical keypad and confirm with OK.
Select the printing format (for JPEG files): A4 or
LETTER (depending on model), or PHOTO and
confirm with OK.
3 Select LIST with the ꢀor ꢁbuttons and confirm
with OK.
1. It may be possible that some TIFF files of your USB
memory key cannot be printed due to data format limitation.
- 52 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Select the printing format: THICK or NORMAL
and confirm with OK to start printing.
Read the USB memory key contents
After a period of inactivity, your machine will return to the
main menu. To view the USB memory key again please
proceed as follows:
5 Exit this menu by pressing the
button.
Delete your files stored on the key
You can delete files stored on your USB memory key.
ꢀ06 - MEDIA / DELETE
ꢀ07 - MEDIA / MEDIA ANALYSIS
1 Press ꢀ, enter 07 using the keypad.
2 The scanning of the USB memory key is started.
3 You can print or delete the detected files stored on
your USB memory key. Refer to the previous
chapters.
1 Insert the USB memory key into the front of the
machine.
MEDIA ANALYSIS appears on the screen.
2 Select DELETE with the ꢀor ꢁbuttons and
confirm with OK.
Save a document on a USB memory
key
3 You have three possible ways of deleting your files:
-
ALL, to delete all the files stored on the USB
memory key.
Select ALL with the ꢀor ꢁbuttons and
confirm with OK.
This function allows you to scan and save a document
directly in the folder Phaser3100MFP_X\SCAN on a USB
memory key. The folder Phaser3100MFP_X\SCAN is
created by the application.
You come back to the previous menu.
-
SERIES, to delete a series of files stored on the
USB memory key.
Select SERIES with the ꢀor ꢁbuttons and
confirm with OK.
Before scanning a document, make
sure that your USB memory key has
sufficient disk space. If not, you can
Important
delete manually the files, see
FIRST FILE and the first indexed file appears
on the screen. Select with the ꢀor ꢁbuttons
the first file of the series to delete and confirm
with OK. A star (*) appears on the left of the file.
LAST FILE appears on the screen, select with
the ꢀor ꢁbuttons the last file of the series to
delete and confirm with OK. A star (*) appears
on the left side of the file.
1 Place the document to be scanned face down on
the document glass.
2 Insert the USB memory key into the front of the
machine.
The scanning of the USB memory key is started.
When the scanning is finished, the MEDIA menu is
displayed.
Press the
button.
You come back to the previous menu.
3 Select SCAN TO with the ꢀor ꢁbuttons then
confirm with the OK button.
-
SELECTION, to delete only one or several files
stored on the USB memory key.
Select with the ꢀor ꢁbuttons the file to delete
and confirm with OK. A star (*) appears on the
left side of the file.
You can also access this function in
two other ways:
Repeat this step for each file you want to delete.
•
•
by pressing the
button then
Press the
button.
Important
by selecting SCAN-TO-MEDIA.
You come back to the previous menu.
by pressing the ꢀbutton from the
screen saver then by typing 03 on
the numerical keypad.
4 Exit this menu by pressing the
button.
4 Choose between B&W SCAN or COLOUR SCAN
with the ꢀor ꢁbuttons and confirm with OK.
5 With the alphanumerical keypad, give a name to
the scan file (up to 20 characters) and confirm
with OK.
6 Choose the scan format between IMAGE and PDF,
and confirm to start the scan and the recording of
the document.
IMAGE allows to have the same kind of file as a
photo. PDF is a format for the digital documents
- 53 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
creation.
With the IMAGE format, if you have
selected:
•
•
BLACK&WHITE, the picture will
be saved in TIFF format.
COLOUR, the picture will be
saved in JPEG format.
You can choose the image resolution
that will be scanned to the USB
memory key; the default resolution is
AUTO.
Important
Press the
button several times
and select the resolution you require:
•
•
Scanning in BLACK&WHITE:
-
-
icon: text resolution.
icon: photo resolution.
- no icon: auto resolution.
Scanning in COLOUR:
-
icon: text resolution.
- no icon: auto resolution.
Pressing
immediately starts the scan and sends a
file to the USB memory key with the parameters defined
in the scan format.
- 54 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
•
to the rear USB port
Telephony (option)
The machine lets you connect a USB-DECT base to one
of the USB ports of the device and register DECT
handsets to this base.
You can then make and receive calls with the registered
DECT handsets using the machine telephone line
(standard cordless telephone use).
The telephony feature is an option
working only with a specific USB
DECT dongle that you can obtain from
your retailer.
Note
You will find further information on our
You can now make and receive calls with the handset
supplied with the DECT base. As the telephone line is
now used for both communication (fax, SMS) and
telephony features, you may need to adjust the machine
Because the machine and the DECT base use the same
telephone line, please consider the following points:
•
the telephony feature only supports voice calls. SMS
service is not available on registered handsets, as well
as Caller Identification Display (CID) and notification,
even if DECT devices used support this function.
Registering DECT handsets
•
when a handset is used, the line is busy. As a result,
the machine cannot perform fax or SMS
communication operations. Sending and receiving
resumes when the line is freed.
By default, the USB-DECT base comes with one
registered handset. To register additional handsets (GAP
compatible) to the base, you will need to put both the base
and the handset in registration mode.
•
•
print and scan operations may take slightly more time
when performed during a DECT communication.
This menu is available only if the
the machine and registered handset(s) cannot share
directories.
USB-DECT base is connected to the
machine.
Important
To register a handset to the DECT base:
Connecting the USB-DECT base
ꢀ 891 - ADVANCED FCT / DECT / REGISTER
Connect your DECT base to one of the USB ports of the
machine:
1 Put the handset in registration mode.
•
to the front USB port
To know the exact registration
procedure of the handset, please refer
to its documentation.
Note
2 On the machine, press ꢀ, enter 89 using the
keypad and confirm with OK.
3 Select REGISTER using the ꢀor ꢁ button and
confirm with OK.
The machine starts searching for the handset.
During the registration process (up to one minute), the
LCD screen displays HANDSET REGISTRATION. The
message disappears once registration is complete.
If the registration process fails (for
example, the handset left the
registration mode too soon), the
machine emits a 3-beep signal. In
Important
this case, repeat the procedure from
step 1.
- 55 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Customising telephony settings
This function lets you set the handset ringing time upon
call reception.
This parameter, used to define for how long the
handset(s) rings before terminating a call, is by default set
to 30 seconds.
This menu is available only if the
USB-DECT base is connected to the
machine.
Important
ꢀ 893 - ADVANCED FCT / DECT / RINGING TIME
1 Press ꢀ, enter 89 using the keypad. Confirm
with OK.
2 Select RINGING TIME using the ꢀor ꢁ button
and confirm with OK.
3 Enter the desired time in seconds (15 to 60) using
the numerical keypad.
4 Confirm with OK.
5 To exit this menu, press
.
Unregistering DECT handset
This function is used to unregister a handset from the
DECT base. You will no longer be able to make or receive
calls with a handset once you unregister it.
This menu is available only if the
USB-DECT base is connected to the
machine.
Important
ꢀ 892 - ADVANCED FCT / DECT / UNREGISTER
1 Press ꢀ, enter 89 using the keypad. Confirm
with OK.
2 Select UNREGISTER using the ꢀor ꢁ button and
confirm with OK.
The LCD screen displays the list of handsets
registered to the DECT base.
3 Select the handset to unregister using the ꢀor ꢁ
button and confirm with OK.
4 Confirm with OK.
5 To exit this menu, press
.
- 56 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
PC Features
Introduction
Software installation
This section describes the following installation
procedures:
•
•
full installation of the Xerox Companion Suite
software,
The Xerox Companion Suite software allows the
connection of a personal computer with a compatible
machine.
installation of the drivers only.
Installing the full software package
From the PC, you can:
Turn your PC on and log in as administrator.
•
•
•
manage the machine, allowing you to set it up
according to your needs,
1 Open the CD-ROM drive, insert the installation CD-
print your documents on the machine from your usual
applications,
ROM and close the drive.
2 An installation procedure is automatically run (Auto
run). If it does not, double-click on setup.exe at the
CD-ROM's root.
scan colour, grey scale or black and white documents
and edit them on your PC, or convert them into text
using the character recognition software (OCR).
3 A screen titled XEROX COMPANION SUITE appears.
This screen allows you to install and uninstall the
software, access the product's user guides or
browse the CD-ROM contents.
Configuration requirements
The minimum configuration requirements for your
personal computer are:
4 Place your cursor on INSTALL PRODUCTS and
confirm with left-click of the mouse.
Supported operating systems:
•
•
•
•
Windows 2000 with at least Service Pack 3,
Windows XP (Home and Pro),
Windows 2003 server for printing driver only,
Windows Vista.
Processor:
•
•
•
800 MHz for Windows 2000,
1 GHz for Windows XP (Home and Pro),
1 GHz for Windows Vista.
5 The Products Installation screen appears.
Place your cursor on ALL PRODUCTS and confirm by
left-click with the mouse.
A CD-ROM drive
A free USB port
The full installation copies the software
required for the good execution of the
Xerox Companion Suite kit onto your
PC.
600 Mbytes of available disk space for the installation
RAM memory:
•
•
128 Mbytes minimum for Windows 2000,
192 Mbytes minimum for Windows XP (Home and
Pro).
The kit consists of:
- Xerox Companion Suite (machine
management software, printer drivers,
scanner, ...),
•
1 GByte for Windows Vista.
- Adobe Acrobat Reader,
Note
- PaperPort.
You may already be the owner of a
version of the software available in the
installation CD-ROM.
In this case use the CUSTOMIZED
installation, select the software that
you want to install on your hard drive
and confirm your choice.
- 57 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Installing drivers only
This section describes the following installation
procedures:
•
•
installation of drivers using the Xerox Companion
Suite software,
manual installation of drivers.
Installing the drivers using the Xerox
Companion Suite software
Turn your PC on and log in as administrator.
The installation is launched.
1 Open the CD-ROM drive, insert the installation CD-
ROM and close the drive.
2 An installation procedure is automatically run (Auto
run). If it does not, double-click on setup.exe at the
CD-ROM's root.
3 A screen titled XEROX COMPANION SUITE appears.
This screen allows you to install and uninstall the
software, access the product's user guides or
browse the CD-ROM contents.
4 Place your cursor on INSTALL PRODUCTS and
confirm with left-click of the mouse.
The following screen appears to indicate the
progression of the installation.
6 Click on OK to finish the installation.
5 The Products Installation screen appears.
Place your cursor on CUSTOMIZED and confirm by
left-click with the mouse.
Your Xerox Companion Suite kit is successfully installed
on your PC.
You can now connect your machine, refer to paragraph
You can start the machine's management software from
the menu START > ALL PROGRAMS > XEROX COMPANION
SUITE > PHASER 3100 MFP > COMPANION DIRECTOR or by
clicking on the icon XEROX COMPANION DIRECTOR located
on your desktop.
- 58 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
6 Place your cursor on XEROX COMPANION SUITE and
10 The final installation is ready to be executed. Click
on the INSTALL button.
confirm with left-click of the mouse.
7 The welcome screen appears. Click on the NEXT
button to launch the installation of the Xerox
Companion Suite kit on your PC.
11 A screen informs you of the installation progress.
12 Click on OK to finish the installation.
8 Select INSTALL DRIVERS in the list and click on the
NEXT button.
The Xerox Companion Suite software is now installed on
your PC.
You can now connect your machine, refer to paragraph
9 Select the destination folder for installation and
click on the NEXT button.
- 59 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
click on NEXT.
Installing the drivers manually
You can install the printer and scan drivers manually
without running any setup software.
This installation mode is only possible
Note
on Windows 2000, XP and Vista.
1 Locate your USB cable connectors and connect as
shown below on the picture.
6 A screen informs you that the drivers have been
installed. Click on the CLOSE button.
You can now use the machine to print and scan your
documents.
Connections
Make sure that your machine is powered off. The
connection between the PC and the machine requires a
USB 2.0 shielded cable no more than 3 meters long.
2 Power on your machine.
It is recommended to install the
Xerox Companion Suite software
first and then to connect the USB
cable to your machine (see
The PC detects the device.
3 Click on LOCATE AND INSTALL DRIVER SOFTWARE
(RECOMMENDED).
If you connect the USB cable before
installing the Xerox Companion
Suite software the recognition
Important
system (plug and play) identifies
automatically that new hardware has
been added. To start your machine
drivers installation, refer to
instructions on screen. When you
use this procedure, only printing and
scanning functions are activated.
The following screen appears:
1 Locate your USB cable connectors and connect as
shown below on the picture.
4 Open the CD-ROM drive, insert the installation CD-
ROM and close the drive.
The drivers are detected automatically.
5 Select XEROX PHASER 3100MFP in the list and
- 60 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
2 Power on your machine.
Uninstall the drivers using the Xerox
Companion Suite software
The PC detects the device and the drivers are
automatically installed.
Run the programs removal from the menu START
>ALL PROGRAMS >XEROX COMPANION SUITE >PHASER
3100MFP > UNINSTALL.
3 Once the installation is finished, a message
indicates that the drivers are installed correctly.
You can also uninstall XEROX PHASER
3100MFP drivers using the Windows
function ADD/REMOVE PROGRAMS from
Note
the control panel.
1 A confirmation screen appears. Click on the YES
button to continue the XEROX PHASER 3100MFP
drivers program removal.
You can now use the machine to print and scan your
documents.
Software Uninstallation
This section describes the following procedures:
2 The uninstall program is launched. You can cancel
the removal by clicking on CANCEL.
•
•
full uninstallation of the Xerox Companion Suite
software,
uninstallation of the drivers only.
Uninstall the software from your PC
Turn your PC on and log in as administrator.
Uninstall the drivers manually
Run the programs removal from the menu START
>ALL PROGRAMS >XEROX COMPANION SUITE >PHASER
3100MFP > UNINSTALL.
The following drivers must be removed:
•
•
•
print driver
scan driver
modem driver
1 A confirmation screen appears. Click on the YES
button to continue the Xerox Companion Suite
program removal.
To remove the print driver:
1 Open the PRINTERS window (START > CONTROL
PANEL > PRINTERS AND FAXES or START > CONTROL
PANEL > HARDWARE AND SOUND > PRINTERS
depending the operating system).
2 Delete the XEROX PHASER 3100MFP icon.
2 The uninstall program is launched. You can cancel
the removal by clicking on CANCEL.
3 In the PRINTERS window, right-click with the mouse
and select RUN AS ADMINISTRATOR > SERVER
PROPERTIES.
4 Select the DRIVERS tab.
5 Select the XEROX PHASER 3100MFP driver and
click on the REMOVE button.
Uninstall the drivers from your PC
Turn your PC on and log in as administrator.
Depending on the installation mode used, select the
required uninstallation mode:
•
If you have installed the drivers with the Xerox
Companion Suite software, see paragraph Uninstall
•
If you have installed the drivers manually, see
- 61 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Machine Management
6 Select the option REMOVE DRIVER AND DRIVER
PACKAGE and click on the OK button.
The software that you have installed contains two
machine management applications,
COMPANION DIRECTOR and COMPANION MONITOR, which
allow you to:
•
•
•
check whether the machine is connected to your PC,
monitor the machine activities,
monitor the status of the machine consumables from
the PC,
7 A confirmation screen appears. Click on the YES
button to continue.
•
quickly access the graphic editor applications.
8 Click on the DELETE button to confirm the removal.
To manage the machine, run the Companion Director
application by clicking on the icon located on your desktop
or from the menu START >ALLPROGRAMS
> XEROX COMPANION SUITE > PHASER 3100 MFP >
COMPANION DIRECTOR.
Checking the connection between the PC
and the machine
To remove scan and modem drivers:
To check if the connection between the devices is good,
run the COMPANION MONITOR software from the icon
located on the desktop and check that the same
information is displayed on the machine.
1 Open the DEVICE MANAGER window (START
>CONTROL PANEL > SYSTEM > HARDWARE > DEVICE
MANAGER or START >CONTROL PANEL > HARDWARE
AND SOUND > DEVICE MANAGER, depending on the
operating system).
Companion Director
This graphical Interface allows you to run the utilities and
the software to manage your machine.
Graphical presentation
Run the application by clicking on the XEROX COMPANION
DIRECTOR icon located on your desktop or from the menu
START >ALLPROGRAMS > XEROX COMPANION SUITE >
PHASER 3100 MFP > COMPANION DIRECTOR.
2 In the OTHER DEVICES sub-menu, select the XEROX
PHASER 3100MFP item and click on the right button
of the mouse.
3 Select UNINSTALL on the menu and left-click with
the mouse.
Utilities and applications activation
The Xerox COMPANION SUITE graphical interface allows
you to run the following utilities and software:
4 Click on the OK button to confirm the removal.
5 In the IMAGING DEVICES sub-menu, select the
XEROX PHASER 3100MFP item and right-click with
the mouse.
•
•
get HELP from the current documentation,
run the PAPERPORT software (Doc Manager).
6 Select UNINSTALL on the menu and left-click with
the mouse.
To run a software or utility contained in the Xerox
COMPANION SUITE kit, place the cursor on it and left-click
with the mouse.
7 Click on the OK button to confirm the removal.
- 62 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Companion Monitor
Graphical presentation
Status of the connection
The status of the connection between the current device
and the PC is indicated by a colour. The following table
defines the possible states of the connection.
Run the application by clicking on the XEROX COMPANION
MONITOR icon located on your desktop or from the menu
START >ALLPROGRAMS > XEROX COMPANION SUITE >
PHASER 3100 MFP > COMPANION MONITOR.
Colour
Yellow
State
Connection in progress.
Green
Red
Connection established.
The PC cannot connect to the device.
Check the USB connection.
Device parameters
1 Select a device by clicking on its line in the list and
click on PROPERTIES to configure the scanning
parameters to be applied for this device when you
use the SCAN TO function.
From this screen you can monitor the information or
configure your machine from the tabs:
•
•
•
DEVICE SELECTION: Displays the list of devices
managed by the PC.
COMPANION: Presents the machine screen (USB
connection only).
CONSUMABLES: Displays the consumables status.
Device management
This tab shows the list of devices managed by the PC.
2 Select the desired scan MODE in the drop-down
Selecting the current device
menu.
Only one device at a time may be connected to the PC.
The current device may be selected by clicking on the
radio button corresponding to the device.
- 63 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Xerox Companion Suite features
3 Select the desired scan RESOLUTION in the drop-
down menu.
Document scanning
The document analysis can be carried out in two ways:
•
either by the SCAN TO function (application accessible
from the Companion Director window or from the
SCAN button on the machine),
•
or directly from a standard compatible application.
Scanning with Scan To
Run the application by clicking on the XEROX COMPANION
DIRECTOR icon located on your desktop or from the menu
START >ALL PROGRAMS >XEROX COMPANION SUITE >
PHASER 3100 MFP > COMPANION DIRECTOR.
4 Click OK to confirm the new parameters.
Removing a device
1 Select the device from the list and click the minus
sign or REMOVE button.
2 To confirm the removal of the device, click YES. To
cancel the removal, click NO.
The device is no longer displayed in the list.
1 Click on the SCAN TO graphical image or press the
SCAN button on your machine and select SCAN-
TO-PC.
Display the consumable status
2 Select the desired scanner, document feeder or
The following information will be available from the
flatbed (document glass).
CONSUMABLES tab:
•
•
•
•
current consumables status,
number of printed pages,
number of scanned pages,
number of sent and received pages.
3 Customise the advanced properties of the scan by
clicking on the ADJUST THE QUALITY OF THE
SCANNED PICTURE link.
- 64 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
4 Adjust the desired parameters and click on the OK
Printing
button.
You have the ability to print your documents via a USB
connection or a WLAN connection.
During the installation of the Xerox Companion Suite
software, the XEROX PHASER 3100MFP printer driver will
be installed automatically onto your PC.
Printing to the machine
Printing a document on the machine from your PC is like
printing a document in Windows.
1 Use the PRINT command from the FILE menu of the
currently open application on the screen.
2 Select the XEROX PHASER 3100MFP printer.
5 Click on the SCAN button, you can follow the
Printing in duplex mode with the machine
ongoing scan on the screen.
6 At the end of the scan, the scanned picture appears
The machine offers the ability to print a document in
manual duplex mode from your PC.
in the PaperPort window.
In manual duplex, the print
quality and paper transport are
not guaranteed.
- If a problem occurred during
the printing of the first side of
your document, such as
wrinkling, dog ears, etc., do not
use this sheet for manual
duplexing.
CAUTION
- When you load paper, please
true up the end of paper on a flat
surface.
For best results, we recommend
that you use 80 g/m² A4 paper or
20 lbs/m² Letter paper.
If the PaperPort software is not
installed on your hard drive, the
Note
scanned picture will appear on your
To print a document in manual duplex mode:
desktop in TIFF format.
The duplex printing mode is
available only in a paper size
Character recognition software (OCR)
managed by the paper tray.
The manual tray cannot be used to
print in duplex mode.
Important
The character recognition function allows to create a
usable data file for desktop applications from a hardcopy
document or from a picture.
The character recognition only works for printed
characters, such as printer outputs or typed text.
Nevertheless you can request for a handwritten text block
to be kept intact (a signature for instance) by outlining it.
1 Use the PRINT command from the FILE menu of the
currently open application on the screen.
2 Select the XEROX PHASER 3100MFP printer.
Given your machine environment and the character
recognition from your machine, the OCR is done with a
Drag&drop of a document from the PaperPort to the
Notepad icon
.
For more details about the usage of
this software, check the online help of
the product.
Note
- 65 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
3 Check the Duplex box and choose among the two
•
Long sides
binding modes:
Binding mode
Long sides
Printing
Short sides
4 Click on the OK button to begin printing.
5 The machine prints the odd pages (from the higher
odd page to page 1) and the LCD screen displays:
** PRINTING **
** PC **
•
Short sides
6 Once the odd pages are printed, the LCD screen
displays the message **PUT THE PRINTED SHEETS IN
THE PAPER TRAY WITH THE PRINTED SIDE VISIBLE...:
** PUT THE PRIN
... AND PRESS <OK>
The PC generates and prints a page
explaining how to reload the sheets
for a duplex job. Read this page
carefully and place it back with the
other sheets.
Important
it is very important that you return
the explanation sheet to the paper
tray to continue printing correctly.
7 Place the sheets in the paper tray as indicated on
the explanation page and below.
The following illustrations describe the necessary
operations depending on the selected binding
mode:
8 Press OK on the control panel to resume printing.
9 Even pages are printed on the other side of the
sheets. Once all pages are printed, remove the
explanation sheet.
If a paper jam or a paper size error
occurs, the job is cancelled. You
must then resubmit the print job.
Important
- 66 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
2 Select the machine address book.
Address book
3 Click NEW and select GROUP in the displayed
The address book enables you to store the numbers of
the contacts you call the most frequently. The purpose of
this function is to facilitate dialling your contact’s number
when you want to send an SMS or fax. If you want, you
can print the list of numbers stored in the address book.
menu.
You also have the ability to create groups of contacts from
the address book. For example, you can group together
all contacts from a given company or the same service to
which you frequently send common documents.
Add a contact to the machine’s address
book
1 Click on the link ADDRESS BOOK of the window MF
DIRECTOR.
4 Enter the name of the group. The group may
consist of contacts from the address book or new
contacts.
The address book is displayed on the screen.
1st case: group members are from the address
book.
Click SELECT THE MEMBERS.
The selection window is displayed.
2 Select the machine address book.
3 Click on NEW and select CONTACT in the displayed
menu.
The input window for the contact data is displayed.
Select a contact or a group in the zone ADDRESS
BOOK, click on
(to add a contact to the group
you can also double click on it).
Click on OK.
2nd case: adding new contacts.
Click on NEW then add the personal data of the new
contact, as in the procedure for adding a contact.
4 Enter the contact name as well as the fax or GSM
telephone number, the fax transmission rate for
this person and the associated quick dial key. Click
on OK.
5 As soon as the group is complete, click on OK.
The new group is added to the list.
The new contact is added to the list.
Manage the address book
Add a group to the machine’s address book
When you are working in the address book, you can
perform different operations:
1 Click the link ADDRESS BOOK of the window MF
DIRECTOR.
•
•
•
print a list of contacts in your address book,
delete a contact or a group in your address book,
search for a contact or a group of contacts in the
address book using the first letters of the name,
•
check the datasheet of a contact or a group in order to
modify it.
- 67 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Modify the information related to a contact
Fax communications (depending on
model)
1 Select the contact whose data you want to modify,
using the mouse.
The fax communication enables you to:
2 Click on PROPERTIES.
•
send documents as faxes from one of the scanners of
your machine, from the hard disk or from the screen of
your PC,
3 Make the necessary changes in the window
ADDRESS BOOK.
4 Click on OK.
•
•
receive fax documents,
monitor communications through various services: the
inbox, the outbox, the sent items, the outbox log and
the inbox log.
Modify a group
1 Select the group in the address book list.
2 Click on PROPERTIES.
Parameters are available to modify the way your machine
works with regard to fax communications. You can modify
these parameters to adapt the fax communications to
your requirements. For this procedure, refer to paragraph
3 Make the necessary changes.
4 Click on OK.
Delete a contact or a group from the address
book
Presentation of the Fax window
1 Select the name of the contact or the name of the
group you want to delete, using the mouse.
2 Click on DELETE.
When a contact is deleted from the
address book, it is automatically
deleted from any group in which it
Important
may be included.
Print the address book
1 Click on PRINT.
The list of the address book is printed on the
machine (if no contact is selected).
Import or export an address book
Save / Export your address book
This operation lets you save your address book to a file in
EAB format.
Item
1
Action
Create a new fax to send.
1 Select EXPORT in the menu FILE of the window
ADDRESS BOOK.
Delete a fax using one of the fax manager
directories. Except for directories SENT
LOG and RECEPTION LOG for which the
effect of this command is to delete the
entire log
2 Enter the name of the file and select the destination
directory, then click on SAVE.
2
Import an address book
Importing an address book makes it possible to exchange
address book entries between two devices without having
to enter contacts one by one manually. Address books
can be imported from files in EAB format. EAB files are
automatically generated during export.
Print a fax from one of the Fax manager
directories.
3
4
5
Display a fax with the Viewer.
Access to the address book.
The whole address book will be
replaced by the imported address
book.
Important
Stop fax sending (only enabled for the
outbox).
6
7
1 Select IMPORT in the menu FILE of the window
ADDRESS BOOK.
Display all faxes in the selected directory
in the Fax manager.
2 Select the file to import, click on OPEN.
- 68 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
7 Click OK to send your fax to all contacts in your list
Item
Action
of contacts.
8
9
Fax preview.
Fax manager directories.
Your send request can then be checked, if necessary, in
the outbox.
Send a fax from an application
Send a fax
This method is used to directly send a document you have
created using a desktop application without printing it
beforehand.
Send a fax from the hard disk or the machine
1 From your desktop application, select FILE > PRINT.
1 Click the icon
of the window MF DIRECTOR.
2 Click NEW then click FAX.
2 Select the printer COMPANION SUITE FAX and
click OK.
The fax window is displayed.
3 In the zone SOURCES, select SCANNER if your
document is in paper format or MEMORY if the
document is a computer file located on your hard
disk (this file must be in TIFF or FAX format).
4 To send your fax to a contact, enter his/her number
in the field RECIPIENTS and click on
or select a
contact (or group) from one of the address books in
the field ADDRESS BOOK and click on the button
.
Repeat this operation as many times as necessary
(use the button
of contacts).
to delete a contact from the list
5 If necessary, use the advanced options (send later
and resolution) in the tab ADVANCED OPTIONS.
3 To send your fax to a contact, enter his/her number
in the field RECIPIENTS and click on
contact (or a group) from one of the address books
in the field ADDRESS BOOK and click the button
Repeat this operation as many times as necessary
or select a
.
(use the button
of contacts).
to delete a contact from the list
4 If necessary, use the advanced options (send later
and resolution) in the tab ADVANCED OPTIONS.
5 To add a cover page, select the tab COVER PAGE
then click the box WITH THE COVER PAGE. Select
the cover page you want to add from the drop-down
menu, or create a new one. For more information,
6 Click OK to send your fax to all contacts in your list
of contacts.
6 To add a cover page, select the tab COVER PAGE
then click the box WITH THE COVER PAGE. Select
the cover page you want to add from the drop-down
menu, or create a new one. For more information,
Your send request can then be checked, if necessary, in
the outbox.
- 69 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
The send memory (items sent)
Receive a fax
The sent memory is used to keep all faxes you have sent.
The window MF Manager and MF Director show, using
different messages, the reception of a fax. The icon
displayed at the bottom of the window MF Manager and
is
The information in the send memory is:
•
•
•
•
the recipient of the fax,
the date the fax was created,
the date the fax was sent,
the size of the fax.
the icon appears in the task bar.
You can automatically print faxes on reception. To do this,
The outbox log
Follow-up of fax communications
The outbox log is used to keep a history of all fax
communications (successful or failed) that your machine
processes. The log is printed automatically as soon as its
contents fill a page.
Follow-up of fax communications is by means of:
•
•
•
•
•
an outbox,
an inbox,
a sent item memory,
an outbox log,
an inbox log.
The DELETE button deletes the
entire log, and not simply the
selected message(s).
Important
These services enable you to always know exactly what
communications are taking place on the machine,
whether sending or receiving.
The information held in the log is:
•
•
•
the recipient of the fax,
the date the fax was sent,
the status (sent, cancelled ...).
The outbox and inbox logs are automatically printed when
their contents fill a page. After automatic printout, the
machine creates a new log.
The inbox log
The inbox log is used to keep a history of all faxes
received by your machine. The log is printed
automatically as soon as its contents fill a page.
The outbox
In the fax outbox, there are the following:
•
•
•
the requests being sent,
the send later requests,
The DELETE button deletes the
entire log, and not simply the
selected message(s).
Important
the requests for which one or more send attempts
have already been made, and which will soon be
redialed,
The information held in the inbox log is:
•
the cancelled requests (calls not put through).
•
•
•
the sender of the fax,
the date and reception of the fax,
the status.
The requests are displayed in the order in which they are
executed.
The cancelled requests are filed at the end of the list so
that they are more accessible if you want to work with
them (request a new send) or delete them.
- 70 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Fax parameters
Description of the tab FAX PARAMETERS
Access to fax parameters
1 Click on the icon
of the window MF
DIRECTOR.
2 Select TOOLS > OPTION > FAX.
3 Make the adjustments required, referring to the
description of parameters below and click OK.
Description of the tab LOGS AND REPORTS
Option
Description
Transmission
speed
Fax default transmission
speed.
Number of the line where your
machine is connected.
Line number
Dialling prefix
This dialling prefix will be
automatically inserted in front
of the number before sending
on this line.
Option
Description
Must be programmed
according to the type of
switchboard your machine is
connected to.
Automatic printing
of a received
document
The fax is automatically printed
when received.
Type of dialing
Header
Printing of a inbox
report
A report is printed out for each
fax received.
Displays a Communication
Identification Line (CIL) on the
documents you send or on the
documents you receive.
The log is printed automatically
when its contents fill a page.
Printing of inbox log
Corrects communication errors
due to line disturbance. This
option ensures that received
documents are legible. On the
other hand, communication
times may be longer if the line
is bad.
Automatic printing
of a sent document
The fax is automatically printed
when it is sent.
ECM
Printing of an
outbox report
An outbox report is printed after
each fax is sent.
Printing of the
outbox log
The log is printed automatically
when its contents fill a page.
Number of attempts the
Number of attempts machine must make if send
fails to contact a recipient.
Interval between
attempts
Duration between two send
attempts.
- 71 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Details about Option A and B:
Cover page
The cover page is part of a fax document automatically
generated by your machine containing information
concerning the sender, the recipient, the date, the time
sent, comments, etc...
•
Option (A): Open the application that you want to use
to edit the background (Word, Wordpad...). Draw the
background image then print this document in the
printer named "Companion Suite Fax". At that point
the MFSendFax dialog is displayed:
This page may be sent alone or in front of a fax document,
but always at the same time as the document. A
document may be sent with a cover page from the
machine or from your desktop. In the latter case, some of
the information in the cover page may be provided by
yourself when making the send request. It is necessary to
create model cover pages before sending a document
using them. On the other hand, once the cover page is
created, a model cover page may be used for all
documents sent.
Your machine offers the possibility of creating and
customizing some model cover pages which you can
choose when sending a fax.
Creating a cover page template
Creating a cover page creates a template which fields (fax
number, comment, subject and so on) will be
automatically filled by the Fax Application depending on
the information provided for each recipient of a document.
Add any recipient to the recipient list, click on the tab
ADVANCED OPTIONS, select resolution FINE as shown
below:
To create this cover page template, there are two major
steps:
•
•
First step: Create a background image with the logos
and the layout that you wish.
Second step: Add the field that you want to be
displayed in the cover page: fax number, comment,
subject and so on. As mentioned before, these fields
will be filled by Fax application at emission time.
For the first step, there are two methods to create the
background image.
You can either
•
Option (A): Draw this background image in your
preferred application (such as Word, Excel,...),
OR
Option (B): Scan a sheet of paper containing the
layout of the cover page.
Finally click on the button SAVE AS DRAFT in the lower
right corner (floppy disk icon). The background image
is created in the directory C:\Program
Files\Companion Suite Pro
•
LM\Documents\FAX\Temporary and has the file
extension .fax
- 72 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
•
Option (B): Launch MFMANAGER, select NEW FAX,
For the second step:
select the scanner source as shown below:
Now that the background image is created in directory in
C:\Program Files\Companion Suite Pro
LM\Documents\FAX\Temporary, you can add the fields
on top of the background image.
Please follow the procedure below:
(a) Launch MFManager, select New Fax, click on the
tab Cover Page, and check the check box named
With the cover page.
(b) Click on the button New, this displays a new window
with the title Creation of the cover page.
(c) Press the button Open in the toolbar, change the file
filter to *.fax and browse to the directory C:\Program
Files\Companion Suite Pro LM \Documents\FAX
\Temporary that contains the background image that
you have created in the First step.
(d) Click on the button Fields in the toolbar, a window
pops up allowing you to add the fields on top of the
background image.
Add any recipient to the recipient list, click on the tab
ADVANCED OPTIONS, select resolution FINE as shown
below:
(e) Click on the button Save to save the Cover Page
template and exit this window.
(f) The window New Fax is displayed, you can now
choose the Cover Page template that you want to
use. When you double click the preview image in the
lower right corner, another window pops up giving
you a preview of the cover page with the fields filled
with the recipient's information.
Creating a cover page
It is necessary to create a model
cover page before sending a fax
with it.
Important
1 From the tab COVER PAGE, click on the button NEW.
2 Select the model cover page you have created
using the menu FILE.
Finally click on the button SAVE AS DRAFT in the lower
right corner (floppy disk icon). The background image
is created in the directory C:\Program
Files\Companion Suite Pro
A window with the model cover page you have
created is displayed:
LL 2\Documents\FAX\Temporary and has the file
extension .fax.
Whether you choose Option A or B, you end up with a
background image with extension .fax, which is located in
C:\Program Files\Companion Suite Pro
LL 2\Documents\FAX\Temporary.
You can now proceed to the second step right
Î
below.
- 73 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Description of the tab COVER PAGE
3 Click on the icon
to display the available
fields.
Field
Description
Either the name of the page
selected by default or the page
you have selected to use.
Name of the cover
page
To add a field, proceed as follows:
You can enter information
concerning the sender.
Sender
- Select the field you want to insert by clicking the
field palette. A stamp replaces the cursor of your
mouse.
- Click the location where you want to put the field
on the model. To delete a field you have just added,
select it and press the delete key on your keyboard.
- You can move or enlarge the field as you like.
You can enter information
concerning the recipient.
If the word Auto is entered in
one of the fields, the field is
updated during sending if the
recipient is listed in the address
book, favourites, a group or a
distribution list.
Recipient
Adjust the size of your field so that
Important
the text is readable.
4 As soon as fields are inserted, save the cover
page.
This is an editing window with
all the basic functions of a text
editor so that you can enter a
text which will be sent in the
cover page.
This cover page can be selected in the tab COVER PAGE of
the fax send window.
Comments
The preview enables you to
see the cover page you are
going to send.
Preview of the
model
- 74 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Send an SMS
SMS Communications (depending on
model)
1 Click on the icon SMS
of the window MF
From your PC, you can send SMS to a single recipient or
to multiple recipients using the distribution groups.
Communications being sent are monitored by means of
the outbox, the outbox log and the outbox memory (items
sent).
DIRECTOR.
2 Click on NEW then on SMS.
The SMS service is available
depending on the countries and the
operators.
Important
Presentation of the SMS window
3 Enter your message in the field CONTENT OF
MESSAGE provided for this purpose.
You can use the buttons and the "smiley" located
to the left of the input field to customize your
message, or to automatically insert the date and
time.
4 To send your SMS to a contact, enter his/her
number in the field TELEPHONE NUMBER and click
on
the address directory in the field CONTACT LIST and
click on
or select a recipient (or group) from one of
.
Item
1
Action
Repeat this operation as many times as necessary
Write an SMS.
(use the button
of contacts).
to delete a contact from the list
Delete an SMS from one of the SMS
manager directories. Except for the
directory SEND LOG for which the effect of
this command is to delete the entire log.
5 If necessary, program the advanced features (to
2
send later or give priority to the SMS) by pressing
the button ADVANCED PARAMETERS (
).
Print an SMS from one of the SMS
manager directories.
3
4
5
Display an SMS with the Viewer.
Access to the address book.
Stop SMS sending (only enabled for the
outbox).
6
7
Displays all SMSs in the directory selected
in the Fax manager.
8
9
SMS preview.
SMS manager directories.
6 Click on OK to send your SMS to all contacts in
your list of contacts.
Your send request can then be checked, if necessary, in
the outbox.
- 75 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
The sent item memory (items sent)
Follow-up of SMS
The sent item memory is used to keep a copy of all SMS
messages you have sent.
SMS communications are monitored by means of:
•
•
•
an outbox,
a sent item memory,
an outbox log.
The information in the sent item memory is:
•
•
•
•
the SMS recipient,
the date of creation of the SMS,
the date of sending of the SMS,
the size of the SMS.
These services make it possible to have complete
information on the machine activity with regard to
communications.
The outbox log is automatically printed when its contents
fill a page. After this automatic printing, the machine
creates a new log.
SMS Parameters
Access to SMS parameters
The outbox
The following is grouped in the SMS outbox:
1 Click the icon SMS
of the window MF
•
•
•
requests being sent,
send later requests,
DIRECTOR.
2 Select TOOLS > OPTIONS > SMS.
requests for which one or more send attempts have
already been made, and which will soon be redialed,
3 Make the adjustments required, referring to the
description of the parameters below and click OK.
•
requests which have been cancelled.
Description of the tab LOGS AND REPORTS
The outbox log
The outbox log is used to keep the entire history of SMS
communications (successful or failed) that have been
processed by your machine. The log is printed
Option
Description
Automatic printing
of a sent document
The SMS is automatically
printed when it is sent.
automatically as soon as its contents fill a page.
The DELETE button deletes the
Printing of a send
report
An outbox report is printed after
each SMS is sent.
entire log, and not simply the
selected message(s).
Important
Printing of the
outbox log
The log is automatically printed
when its contents fill a page.
The information held in the log is:
•
•
•
the SMS recipient,
the date of sending of the SMS,
the status (sent, cancelled,...).
- 76 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
To replace the print cartridge, proceed as shown below.
Maintenance
1 Insert the smart card provided with the new print
cartridge as shown on the picture below.
Service
General information
For your safety, it is imperative to
refer to the security directives
CAUTION
The following message appears:
To ensure that your machine is kept in the best
conditions, it is recommended that you periodically clean
the interior of the machine.
CHANGE TONER?
YES=OK - NO=C
2 Press OK.
Please respect the following rules while using this
machine:
The following message appears:
OPEN FRONT COVER
REPLACE TONER
- Do not leave the scanner cover open.
- Do not try to lubricate the device.
- Do not close the scanner cover violently or do not
apply vibrations to the machine.
- Do not open the print cartridge access cover while
printing.
- Do not try to disassemble the machine.
- Do not use paper which has stayed in the tray for too
long.
3 Stand in front of the device.
4 Grasp the left and right sides of the cover and pull
it towards you at the same time.
5 Raise and remove the print cartridge from the
machine.
6 Unpack the new cartridge, insert it into its slot by
pushing it until it clicks, then gently push the handle
down (as shown below).
Print cartridge replacement
Your machine comes with a current consumable
management system. It tells you if your print cartridge is
close to its end of cycle.
The following messages will appear on your machine
screen when the print cartridge reaches the critical
threshold (less than 10% print cartridge left) and when it
is empty:
TONER NEAR
END
TONER EMPTY
REPLACE <OK>
You can however change the print cartridge at any time,
before it reaches its end of cycle.
Always use the smart card provided
when replacing the print cartridge.
The smart card contains the
information necessary to reset the
level of toner. Replacing the print
cartridge without using a smart card
may result in the consumable
management system being
inaccurate.
Important
7 Close the cover.
The following message appears:
HAVE YOU CHANGED
THE TONER? <OK>
8 Press OK.
- 77 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
A wait message appears.
Automatic Document feeder roller cleaning
PLEASE
WAIT
Clean the roller of the document feeder when:
•
one or more vertical lines appear on the copies of
documents placed on the document feeder (presence
of debris, ink, glue, etc., in the paper transport
mechanism).
The smart card is read.
NEW TONER
•
the message **YOU SHOULD CLEAN THE ROLLER OF THE
SCANNER FEEDER. PLEASE REFER TO USER MANUAL.
PRESS <STOP> WHEN THE ROLLER IS CLEANED** warns
you that the document feeder cannot transport paper
sheets anymore (dust, dirt or debris obstructing the
rollers). Press OK to clear the message on the screen.
REMOVE CARD
9 Remove the smart card from the reader, your
machine is ready to print again.
Issues with smart cards
To clean the document feeder roller, proceed as shown
below:
If you use a smart card that has already been used, the
machine will display:
PLEASE
WAIT
1 Press the On/Off button to turn off the device
(0 position) and unplug the power cord.
2 Open the document feeder scanner cover.
then,
REMOVE CARD
ALREADY USED
If you use a defective smart card, the machine will display:
PLEASE
WAIT
then,
UNKNOWN CARD
REMOVE CARD
If the C button is pressed while the smart card is being
read, the machine displays:
3 Clean the rollers of the document feeder and the
two idler rollers located on the mobile part of the
scanner with a soft lint-free cloth dampened with
mild alcohol.
ACTION CANCELLED
REMOVE CARD
Cleaning
To clean them, rotate them in the same direction as
during paper transport.
Document glass cleaning
When one or more vertical lines appear on the copies,
clean the glass of the scanner.
1 Open the scanner cover until it is standing in
vertical position.
2 Wipe the glass with a soft lint-free cloth dampened
with mild alcohol.
3 Close the scanner cover.
4 Make a copy to check that the symptoms have
disappeared.
Printer cleaning
Dust, dirt and paper debris on the exterior and internal
surfaces of the printer can affect its operation. We advise
that it be cleaned regularly.
4 Wipe the rollers with a soft, dry lint-free cloth until
they are dry.
5 Close the document feeder scanner cover.
6 Plug the power cord into the wall outlet and press
Cleaning the machine’s exterior surfaces
the On/Off button to turn on the device (I position).
Clean the external part of the printer with a soft cloth
dampened in mild detergent.
7 Make a copy to check that the symptoms have
disappeared.
- 78 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Printer issues
Paper jam
When printing, a sheet of paper may get stuck in the
printer or the paper tray and cause a paper jam.
Error messages
When the printer encounters any of the problems
described below, the corresponding message is shown
on the machine display.
In case of a paper jam in the machine, the following
message appears:
PAPER JAM
Message
Action
EXTERNAL TRAY
Check the presence of a
print cartridge in the
machine.
1 Open the paper jam cover located at the back of
CHECK TONER
the machine.
2 Remove the jammed sheet of paper and close the
cover.
Indicates that your
consumable will need
changing soon.
TONER NEAR END
REPLACE PAPER
HEATING
Add paper in tray.
Message displayed when
starting the machine.
CLOSE COVER
PRINTER
The printer front cover is
open, close it.
TONER EMPTY
REPLACE <OK>
Replace the print cartridge.
A sheet of paper is jammed
in the machine. Take out
the print cartridge and
remove the jammed paper
sheet. Take out the paper
tray and remove the
3 Open and close the front cover.
The printer starts again automatically.
PAPER JAM
REMOVE TONER
The fusion unit can reach a very
high temperature during the
jammed paper sheet. Then
open and close the
operation. To prevent any harm, do
not touch this area. For details,
CAUTION
consumable cover.
refer to Positions of Safety labels
A sheet of paper is jammed
in the machine. Open the
paper jam cover. Remove
the jammed paper sheet.
Then open and close the
consumable cover.
In case of paper jam, the following message appears:
PAPER JAM
EXTERNAL TRAY
PAPER JAM
REMOVE TONER
1 Remove the print cartridge and check if a sheet is
jammed.
PAPER EMPTY
Add paper in the paper tray.
2 Remove the sheet of paper which causes the paper
jam.
INFORMATION
**You should clean
the roller of the
scanner feeder.
Please refer to user
manual. Press
3 Put the print cartridge in the machine, or remove
the paper tray and remove the sheet of paper which
causes the paper jam.
The document feeder
cannot transport paper
sheets anymore (dust, dirt
or debris obstructing the
rollers). Clean the roller of
the document feeder.
4 Check that the paper sheets in the paper tray are
correctly placed.
<STOP> when the
roller is cleaned**.
After one of the error messages listed
above is displayed it may result in the
cancellation of an active print job (see
In case of printing of received fax, the
print job is always restarted after
clearing of the error.
Note
5 Replace the paper tray in the machine.
- 79 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Communication errors
ADF Feeding problems
When a paper jam occurs, the following message If the communication fails, the machine advises you of an
appears:
automatic retry later.
Example of what is displayed:
REMOVE DOCUMENT
STOP TO CONFIRM
Current time
Time of next try
FRI 12 DEC 20:13
0142685014 20:18
1 Open the document feeder scanner cover.
Transmission from the feeder
You have the choice between:
•
waiting until the transmission takes place at the given
time,
•
restarting the transmission immediately by
pressing
abandoning transmission by pressing
the document, press again.
,
•
. To eject
2 Remove the jammed paper without tearing it.
3 Close the document feeder scanner cover.
Transmission from memory
You have the choice between:
4 Press
.
•
waiting until the transmission takes place at the given
time,
•
restarting the transmission using the transmission
queue. In this case, for a document composed of
several pages, the transmission will take place from
the page where the error occurred (see Performing
page 31),
Miscellaneous problems
When turning on the machine, nothing is displayed
on the screen.
Check the connection between the power cord and the
outlet.
•
abandoning the transmission by deleting the
corresponding command in the transmission line (see
The machine does not detect the presence of the
document inserted in the document feeder.
The message READY does not appear on the screen.
At the start and during scanning, REMOVE DOCUMENT
appears on the screen.
The machine makes at most 5 automatic redials. The
non-transmitted document is automatically deleted from
the memory and a transmission report is then printed
together with an error code and the cause for
transmission failure (see the communication error codes).
1 Remove the document or press button
.
2 Check the thickness of the document (50 sheets of
paper of 80 g/m2).
3 Smooth out the sheets if needed.
4 Help the sheets along.
Communication error codes
The communication error codes appear in the logs and
transmission reports.
The machine does not receive any faxes.
1 Check that the telephone line cable is correctly
General codes
plugged in.
2 Check that there is a tone signal on the telephone
Code 01 - Busy or no fax answer
This code appears after 6 unsatisfactory attempts. Call
later.
line by pressing
.
Code 03 - User break
A communication has been stopped by the user pressing
You receive a blank page.
1 Make a photocopy of a document; if it is correct
then your fax is functioning normally.
the button
.
2 Call back the subscriber and have him / her resend
the document. It was probably sent with the sheet
inserted backwards.
Code 04 - Non programmed number
A number saved as a one-touch key or abbreviated
number is not valid, check it. (Example: a delayed
transmission was programmed with a one-touch key and
this key has been deleted in the meantime).
Code 05 - Scanning default
You cannot send a fax.
1 Check that the telephone line cable is correctly
plugged in.
An incident occurred with the scanner, for example, the
sheet is jammed.
2 Check the tone signal by pressing the button
.
3 Check the prefix is correctly programmed and
used.
- 80 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Code 06 - Printer default
PC printing issues
An incident occurred in the printer: no paper, paper jam,
opened cover... In the reception mode, this incident
appears only if the reception parameter is switched to
WITHOUT PAPER.
This section details how the machine handles a print
request after having encountered an issue (paper jam,
connection loss, etc.).
Code 07 - Disconnected
Refer to the sections below to know if the printing of your
document will resume or will be cancelled, depending on:
The link has been cut (bad line). Check the number and
try again.
Code 08 - Quality
•
•
the connection to the PC,
The document you sent was not well received. Contact
your subscriber to see if you need to send again.
Code 0A - No document to be polled
You tried to poll a document from a subscriber who had
not prepared his/her document (no deposit) or the
password entered was incorrect.
the problem encountered during printing.
PC printing via USB connection
Code 0B - Wrong number of pages
Issue encountered
Print request handling
There is a difference between the number of pages
indicated during preparation for the transmission and the
number of pages sent. Check the number of pages in the
document.
Once the problem is resolved,
printing resumes from the first
non-printed page.
Paper empty
Code 0C - Received document error
Ask the subscriber who called you to check the length of
his/her document (it may be too long to be completely
received).
Code 0D - Transmission failed
Ask the sender to resend the document.
Code 13 - Memory full
Your fax can no longer receive since its memory is full.
There are too many received unprinted documents or too
many documents in the transmission line.
Print the received documents and delete or transmit
immediately the documents in the transmission line.
Code 14 - Memory full
No paper feed
Paper jam
Once the problem is resolved,
printing resumes from the first
non-printed page.
Exception: If the document
was to be printed in manual
duplex mode, the printing of
the document is cancelled.
Paper format problem
The printing of the active
document is cancelled.
Documents waiting to be
printed, however, will print
after the print cartridge is
replaced.
Toner empty
Received document memory full. Print all received
documents.
Code 15 - Unknown mailbox number
You wish to deposit a document in a subscriber’s mailbox.
The mailbox number does not exist.
The machine switches to idle
mode after a timeout (30
seconds by default).
The printing of the active
document is cancelled.
Documents waiting to be
printed, however, will be
printed.
Code 16 - No Relay Bcst list Nr x
Pause requested
from the spooler
You requested a document relay from a remote fax but
the fax has not programmed the list of subscribers
requested.
Code 17 - Unknown mailbox number
You wish to recover a document from a subscriber’s
mailbox. The mailbox number does not exist.
Code 18 - Relay Bcst impossible
You requested a document relay from a remote fax which
does not have the relay broadcast function.
Code 19 - Subscriber has stopped
The communication has been stopped by your
subscriber. (Example: a fax wanted to poll your fax but
there is no document deposited).
Once the problem is resolved,
the printing of the document
restarts from the beginning,
regardless of the number of
pages already printed before
the connection loss.
Loss of USB
connection
Code 1A - Disconnected
The transmission has not started. The telephone line is
busy.
Code 1B - Transmission failed
During transmission: start again.
During reception: ask your subscriber to resend the
document.
Code 50 - Server error
Check the number configured for the SMS server or a
communication error occurred during data transmission.
- 81 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
PC printing via WLAN connection
Firmware update
Updating the machine firmware requires that the Xerox
Companion Suite software be installed on your PC, and
that the PC is connected to the machine (see PC
Issue encountered
Print request handling
Once the problem is resolved,
printing resumes from the first
non-printed page.
Paper empty
updates are available for your machine, and download the
appropriate update file on your PC.
No paper feed
Paper jam
Once the problem is resolved,
printing resumes from the first
non-printed page.
Then, access the update utility (START > ALL PROGRAMS
> XEROX COMPANION SUITE > PHASER 3100 MFP
Exception: If the document
was to be printed in manual
duplex mode, the printing of
the document is cancelled.
> COMPANION -
downloaded file and launch the update.
FIRMWARE
UPDATE),
select
the
Paper format problem
manual after the software is updated.
The printing of the active
document is cancelled.
Documents waiting to be
printed, however, will be
printed.
Toner empty
or
Printing resumes from the
first non-printed page.
The machine switches to idle
mode after a timeout (30
seconds by default).
The printing of the active
document is cancelled.
Documents waiting to be
printed, however, will be
printed.
Pause requested
from the spooler
Once the problem is resolved,
the printing of the document
restarts from the beginning,
regardless of the number of
pages already printed before
the connection loss.
Loss of WLAN
connection
- 82 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Specifications
Physical specifications
Dimensions:
Weight:
412 x 447 x 386 mm
13 kg
Electrical specifications
Power supply (see rating plate):
Single phase 120 V - 50/60 Hz - 8.5 A or
Single phase 220-240 V - 50/60 Hz - 4.5 A
according model (see rating plate)
13 W typical in powersave
Electric consumption:
13 W typical in standby
450 W average during printing (900W peak)
Environmental specifications
Operating temperature:
10 °C to 27 °C [50 °F to 80.6 °F] with an ambient humidity
included between 15 to 80% (up to 32°C [89.6 °F] with an ambient
humidity included between 15 to 54%)
Peripheral specifications
Printer
Type:
Resolution:
Speed:
Laser (on normal paper)
600 dpi
a
20 ppm maximum
Preheating time:
First page out time:
21 sec.
13 sec.
a. Printing speed may vary depending on used operating systems, computer specifications, software applications, connection modes
(USB or WLAN), paper sizes as well as file types and sizes.
Copier
Type:
Autonomous Black and White
20 ppm maximum
600 dpi
99 pages maximum
25 % to 400 %
Copy speed:
Resolution:
Multiple copies:
Zoom range:
Scanner
Type:
Colour scanner
50 sheets
36 bits
600 dpi (optical)
2400 dpi (interpolated)
TWAIN, WIA
Letter
Document feeder capacity:
Colour depth:
Resolution:
Software compatibility:
Maximum paper size:
Printing supports
Main paper tray capacity:
Output tray capacity:
Main tray paper size:
250 sheets maximum (60 g/m²), 200 sheets maximum (80 g/m²)
50 sheets
A4, A5, Statement, Legal, Letter
60 to 105 g/m² paper
A4, A5, Statement, Legal, Letter, B5, exec, A6
52 to 160 g/m² paper
Paper size for manual printing:
PC connection
Slave USB 2.0 port (PC connection)
Master USB 2.0 port (Wlan connection, reader, USB memory key reader, USB-DECT base dongle - option)
Operating System: Windows 2000 ≥ SP3, Windows XP, Windows Vista, Windows 2003 server (for printing only)
- 83 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Consumable specifications
Print cartridge
Phaser 3100MFP Standard-Capacity Print Cartridge
106R01378
106R01379
Phaser 3100MFP High-Capacity Print Cartridge
Specifications are subject to changes for improvement without notice.
- 84 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Phaser 3100MFP/X
Customer Information
As part of our continuing quest for total customer satisfaction, all of our products are made with ease-of-use and
reliability in mind.
If you need assistance during or after product installation, please visit the Xerox website for online solutions and
support:
- 85 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|