DESCRIPTION
These small IR receivers have been designed for mounting in very small
spaces. They may be mounted under shelf edges, cabinet ledges, in wall
speakers, etc. – anywhere an inconspicuous appearance is desired. The high
sensitivity of these receivers allows placement behind speaker grilles and still
receive IR commands up to 60 feet away*.
FEATURES
•
•
•
Wire channel for clean installation.
System testing red-talk-back LED.
Includes 3-Terminal Block for easy extension to remote room locations.
INSTALLATION INSTRUCTIONS
SPECIFICATIONS
•
•
•
•
•
•
•
•
•
Infrared carrier frequency bandwidth: 30 - 60 kHz.
Reception range: Up to 60 feet.*
Reception angle: +/- 60 degrees.
Cable requirements: See “INSTALLATION” below.
Max. Transmission length: 1 mile using 18 gauge wire.
Maximum current output: 100mA.
Drives IR emitters through Xantech Connecting Blocks, Controllers, etc.
Dimensions: 2.55” x 0.55” x 0.35” (65mm x 14mm x 9mm).
Power requirements: +12VDC, 10mA.
DL25
Dinky Link™ Surface Mount
Standard IR Receiver
* Depending on remote control output strength and ambient conditions.
MOUNTING
The IR receiver can be mounted to any flat surface, using the two-sided
adhesive tape supplied. Two screws are included for mounting the 3-terminal
block provided with the IR receiver.
An additional feature is a wire channel on the rear of the surface mount IR
receiver. This will give the installer the ability to provide clean wire dressing in
any direction.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING:
Limited Warranty
Xantech® warrants its products to be free of defects in materials or workmanship. This is a
Limited Lifetime warranty from the date of purchase by the original consumer. Any products
returned to Xantech and found to be defective by Xantech within the warranty period will be
repaired or replaced, at Xantech’s option, at no charge. Xantech will not be responsible for the
actual cost of installation or removal of the product, nor for any incidental or consequential
damages. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation may not apply to you. This warranty gives you specific legal
rights. You may have additional legal rights that vary from state to state.
1. Perhaps the most common problem you may encounter is stray IR
(infrared) or RF (radio frequency) interference preventing proper
operation of the controlled equipment.
•
Fluorescent, Compact Fluorescent, Neon or Halogen lights,
Neon Art, and light dimmers.
•
•
•
Direct or reflected sunlight.
Infrared security sensors (active types).
RF radiation from TV sets that may be close to the Dinky Link
IR Receiver.
2. You can confirm the source of the interference by temporarily turning
off TV sets, isolating the Dinky Link IR Receiver from all sunlight and
turning off all lights, light dimmers and Infrared security systems.
Then check to see if the Dinky Link IR Receiver operates the
component.
•
•
•
Sometimes interference will cause the red Talk-Back LED on
the front of the Dinky Link IR Receiver to blink dimly,
intermittently, or continuously.
The Talk-Back Led should only blink when you are sending
infrared commands to the Dinky Link IR receiver from a
remote control.
It may be necessary to move either the interfering source of
the Dinky Link IR Receiver to achieve proper operation.
3. If the Talk-Back LED or the 283D Emitters do not blink when you are
sending IR commands to the Dinky Link IR Receiver from a remote
control, check the following:
•
Make sure the power supply is plugged securely into a live
AC electrical outlet.
•
Be sure the stereo mini plug of the Dinky Link IR Receiver is
plugged into the “IR RCVR” jack on the CB12 Connecting
Block, not into the “OUT” jack.
•
Check to see that all the mini plugs are properly seated into
the mini jacks on the CB12 Connecting Block.
4. If the 283D Emitters blink, but the component does not respond,
reposition the 283D Emitter(s). They may not be located directly over
the component’s infrared receiving “window”. Consul the owner’s
manual of the unit or the manufacturer for the exact location of the
infrared “window”.
Xantech Corporation
13100 Telfair Ave., Sylmar CA 91342 | Xantech.com
Installation Instructions, DL25 © 2009 Xantech Corporation
Document # 08905291B
This document is copyright protected. No part of this manual may be copied or reproduced in any
form without prior written consent from Xantech Corporation. Xantech Corporation shall not be
liable for operational, technical, or editorial errors/omissions made in this document.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
|