Woodstock Treadmill M1001 User Manual
MODELꢀM1001ꢀ  
6"ꢀxꢀ26"ꢀVERTICALꢀMILL  
INSTRUCTIONꢀMANUAL  
Phone:ꢀ(360)ꢀ734-3482ꢀꢀ•ꢀꢀOn-LineꢀTechnicalꢀSupport:ꢀtech-support@shopfox.biz  
COPYRIGHTꢀ©ꢀJANUARY,ꢀ2005ꢀBYꢀWOODSTOCKꢀINTERNATIONAL,ꢀINC.,ꢀREVISEDꢀMARCH,ꢀ2011ꢀ(TS)  
WARNING:ꢀNOꢀPORTIONꢀOFꢀTHISꢀMANUALꢀMAYꢀBEꢀREPRODUCEDꢀINꢀANYꢀSHAPEꢀORꢀFORMꢀWITHOUT  
THEꢀWRITTENꢀAPPROVALꢀOFꢀWOODSTOCKꢀINTERNATIONAL,ꢀINC.  
PrintedꢀinꢀChina  
#6799PC  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
INTRODUCTION .....................................2  
MAINTENANCE .................................... 26  
General .......................................... 26  
Cleaning ......................................... 26  
Table and Base.................................. 26  
Lubrication ...................................... 27  
Maintenance Schedule......................... 28  
Maintenance Notes............................. 28  
Woodstock Technical Support ..................2  
About Your New 6" x 26" Vertical Mill.........2  
Machine Specifications ..........................3  
SAFETY...............................................7  
Standard Machinery Safety Instructions ......7  
Additional Safety Instructions for Vertical  
Mills ................................................9  
SERVICE ............................................ 29  
General .......................................... 29  
Gibs............................................... 29  
Adjusting Backlash............................. 30  
Electrical Safety Instructions................. 31  
Electrical Parts Identification................ 32  
Wiring Diagram ................................. 33  
Troubleshooting................................. 34  
Headstock Assembly ........................... 35  
ELECTRICAL ....................................... 10  
SET UP.............................................. 13  
Unpacking ....................................... 13  
Inventory ........................................ 13  
Machine Placement ............................ 14  
Cleaning Machine............................... 14  
Mounting Mill on Shop Floor.................. 15  
Assembly......................................... 16  
Headstock Adjustment ........................ 16  
Handle Installation............................. 16  
Drawbar.......................................... 16  
Single Shot Lubrication........................ 16  
Spindle Controls................................ 17  
Test Run.......................................... 17  
PARTS .............................................. 35  
Headstock Assembly ........................... 35  
Base Assembly .................................. 36  
Machine Parts Lists............................. 37  
Machine Labels ................................. 39  
WARRANTY ........................................ 40  
Warranty Registration ......................... 41  
OPERATIONS....................................... 18  
General .......................................... 18  
Positioning Spindle Head...................... 18  
Table Travel ..................................... 19  
Graduated Dials ................................ 20  
Power Feed Controls........................... 20  
Quill Travel...................................... 21  
Determining Needed RPM..................... 22  
Setting RPM ..................................... 23  
Spindle Break-in Procedure................... 24  
Installing Tools.................................. 25  
Removing Cutting Tools ....................... 25  
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
INTRODUCTION  
Woodstock Technical Support  
We stand behind our machines! In the event that questions arise about your machine, parts are miss-  
ing, or a defect is found, please contact Woodstock International Technical Support at (360) 734-3482 or  
send e-mail to: tech-support@shopfox.biz. Our knowledgeable staff will help you troubleshoot prob-  
lems and send out parts for warranty claims.  
If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.  
If you still have questions after reading the latest manual, or if you have comments please contact us at:  
Woodstock International, Inc.  
Attn: Technical Support Department  
P.O. Box 2309  
Bellingham, WA 98227  
About Your New 6" x 26" Vertical Mill  
Your new SHOP FOX® 6" x 26" Vertical Mill has been specially designed to provide many years of trou-  
ble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program assure  
safe and reliable operation.  
Woodstock International, Inc. is committed to customer satisfaction in providing this manual. It is our  
intent to make sure all the information necessary for safety, ease of assembly, practical use and durabil-  
ity of this product be included.  
-2-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
MODEL M1001  
SHOP FOX® VERTICAL MILL 6" X 26"  
Motors  
Main  
Type......................................................................... TEFC Capacitor Start Induction  
Horsepower........................................................................................... 1-1/2 HP  
Voltage.............................................................................................. 110V/220V  
Prewired.................................................................................................... 110V  
Phase.............................................................................................. Single-Phase  
Amps................................................................................. 16A at 110V, 8A at 220V  
Speed.................................................................................................. 1725 RPM  
Cycle....................................................................................................... 60 Hz  
Number of Speeds............................................................................................. 1  
Power Transfer ................................................................................... V-Belt Drive  
Bearings................................................................. Shielded, Permanently Lubricated  
Main Specifications  
Operation Info  
Spindle Travel.............................................................................................. 3 in.  
Swing....................................................................................................... 11 in.  
Longitudinal Table Travel......................................................................... 14-1/4 in.  
Cross Table Travel......................................................................................... 6 in.  
Vertical Table Travel.................................................................................... 14 in.  
Knee Travel........................................................................................... 11-3/4 in  
Ram Travel................................................................................................ 12 in.  
Head Travel........................................................................................... 2-1/2 in.  
Head Swivel (Left-to-Right).......................................................................... 90 deg.  
Head Swivel (Front-to-Back)......................................................................... 45 deg.  
Turret or Column Swivel (Left and Right)........................................................ 360 deg.  
Maximum Distance Spindle to Column............................................................ 5-1/2 in.  
Maximum Distance Spindle to Table............................................................. 11-7/8 in.  
Drilling Capacity for Cast Iron........................................................................... 1 in.  
Drilling Capacity for Steel............................................................................. 3/4 in.  
Number of Vertical Spindle Speeds......................................................................... 9  
Range of Vertical Spindle Speeds........... 240, 360, 520, 730, 1280, 1320, 1600, 2220, 2760 RPM  
Number of Longitudinal Feeds...................................................................... Variable  
Feed Rate......................................................................................... 0 — 140 FPM  
Quill Diameter........................................................................................ 2.950 in.  
-3-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Table Info  
Table Length.............................................................................................. 26 in.  
Table Width........................................................................................... 6-1/8 in.  
Table Thickness....................................................................................... 1-3/4 in.  
Number of T-Slots............................................................................................. 3  
T-Slots Width.......................................................................................... 0.560 in.  
T-Slots Height......................................................................................... 0.850 in.  
T-Slots Centers...................................................................................... 1-9/16 in.  
Stud Size................................................................................................. 3/8 in.  
Spindle Info  
Spindle Taper................................................................................................ R-8  
End Milling Capacity.................................................................................... 3/4 in.  
Face Milling Capacity..................................................................................... 3 in.  
Drawbar Diameter..................................................................................... 7/16 in.  
Drawbar TPI................................................................................................... 20  
Drawbar Length..................................................................................... 12-1/4 in.  
Spindle Bearings............................................................................... Tapered Roller  
Lead Screw Info  
Leadscrew Diameter................................................................................. 15/16 in.  
Leadscrew TPI.................................................................................................. 8  
Leadscrew Length........................................................................................ 31 in.  
Construction  
Spindle Housing/Quill................................................................................ Cast Iron  
Table............................................................................... Surface-Ground Cast Iron  
Head.................................................................................................... Cast Iron  
Column................................................................................................. Cast Iron  
Base.................................................................................................... Cast Iron  
Stand........................................................................................................ Steel  
Paint....................................................................................................... Epoxy  
Other  
Collar Graduations................................................................................... 0.001 in.  
Recommended Mobile Base........................................................................... D2058A  
Product Dimensions  
Weight.......................................................................................................... 900 lbs.  
Width (side-to-side) x Depth (front-to-back) x Height.............................. 45-1/2 x 41 x 66-5/8 in.  
Footprint (Length x Width)......................................................................... 27-1/2 x 21 in.  
Shipping Dimensions  
Type....................................................................................................... Wood Crate  
Content........................................................................................................ Machine  
Weight.......................................................................................................... 936 lbs.  
Length x Width x Height........................................................................... 37 x 41 x 75 in.  
-4-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Electrical  
Power Requirement............................................................. 110V/220V, Single-Phase, 60 Hz  
Prewired Voltage................................................................................................. 110V  
Minimum Circuit Size................................................................... 20A at 110V, 15A at 220V  
Switch................................................................................................. ON/OFF Switch  
Switch Voltage.................................................................................................... 110V  
Cord Length....................................................................................................... 6 ft.  
Cord Gauge.................................................................................................. 14 Gauge  
Plug Included....................................................................................................... Yes  
Included Plug Type........................................................................................ NEMA 5-15  
Other  
Country Of Origin ............................................................................................... China  
Warranty ....................................................................................................... 2 Years  
Assembly Time ................................................................................................. 1 Hour  
Features  
Milling Head Micro-Feed  
Built-In Work Light  
Class 7 Spindle Bearings  
Head Tilts to 45 Deg. Both Ways.  
Single-Shot Lubrication System  
High-Precision Ground Vertical and Cross Ways  
Accessories  
Drawbar  
Tool Box  
3 In. Shell Mill with Arbor  
Hex Wrench Set, 3-6mm  
Open End Wrenches  
Screwdrivers  
-5-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Controls and Features  
E
D
F
C
G
B
A
N
H
O
M
I
L
J
K
A. Longitudinal Handwheel  
B. Worklight  
C. 3" Shell Mill  
D. Quill Micro-Feed Handwheel  
E. Quill Down Feed Lever  
F. Quill Lock  
G. Power Feed Stops  
H. Longitudinal Power Feed  
I. ON/OFF Buttons  
J. Cross Feed Handwheel  
K. Storage Compartment  
L. Coolant Catch Basin  
M. Knee Lever  
N. Power Feed Limit Switch  
O. Single Shot Lubrication System  
-6-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
SAFETY  
For Your Own Safety,  
Read Manual Before Operating Machine  
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This  
manual uses a series of symbols and signal words intended to convey the level of importance of the  
safety messages. The progression of symbols is described below. Remember that safety messages by  
themselves do not eliminate danger and are not a substitute for proper accident prevention mea-  
sures—this responsibility is ultimately up to the operator!  
Indicates an imminently hazardous situation which, if not avoided,  
WILL result in death or serious injury.  
Indicates a potentially hazardous situation which, if not avoided,  
COULD result in death or serious injury.  
Indicates a potentially hazardous situation which, if not avoided,  
MAY result in minor or moderate injury.  
This symbol is used to alert the user to useful information about  
proper operation of the equipment, and/or a situation that may  
cause damage to the machinery.  
NOTICE  
Standard Machinery Safety Instructions  
Standard Machinery Safety Instructions  
OWNER’S MANUAL. Read and understand this  
owner’s manual BEFORE using machine.  
Untrained users can be seriously hurt.  
HEARING PROTECTION. Always wear hearing  
protection when operating or observing  
loud machinery. Extended exposure to this  
noise without hearing protection can cause  
permanent hearing loss.  
EYE PROTECTION. Always wear ANSI-approved  
safety glasses or a face shield when operating  
or observing machinery to reduce the risk of  
eye injury or blindness from flying particles.  
Everyday eyeglasses are not approved safety  
glasses.  
MENTAL ALERTNESS. Be mentally alert when  
running machinery. Never operate under the  
influence of drugs or alcohol, when tired, or  
when distracted.  
HAZARDOUS DUST. Dust created while using  
machinery may cause cancer, birth defects,  
or long-term respiratory damage. Be aware  
of dust hazards associated with workpiece  
materials, and always wear a NIOSH-approved  
respirator to reduce your risk.  
DISCONNECTING POWER SUPPLY. Always  
disconnect machine from power supply before  
servicing, adjusting, or changing cutting tools  
(bits, blades, cutters, etc.). Make sure switch  
is in OFF position before reconnecting to avoid  
an unexpected or unintentional start.  
WEARING PROPER APPAREL. Do not wear  
clothing, apparel, or jewelry that can become  
entangled in moving parts. Always tie back  
or cover long hair. Wear non-slip footwear to  
avoid accidental slips which could cause a loss  
of workpiece control.  
DANGEROUS ENVIRONMENTS. Do not use  
machinery in wet or rainy locations, cluttered  
areas, around flammables, or in poorly-lit  
areas. Keep work area clean, dry, and well-  
lighted to minimize risk of injury.  
-7-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
APPROVED OPERATION. Untrained operators  
can be seriously hurt by machinery. Only  
allow trained or properly supervised people  
to use machine. When machine is not being  
used, disconnect power, remove switch keys,  
or lock-out machine to prevent unauthorized  
use—especially around children. Make  
workshop kid proof!  
STABLE MACHINE. Unexpected movement during  
operations greatly increases the risk of injury  
and loss of control. Verify machines are  
stable/secure and mobile bases (if used) are  
locked before starting.  
FORCING MACHINERY. Do not force machine. It  
will do the job safer and better at the rate for  
which it was designed.  
ONLY USE AS INTENDED. Only use machine for  
its intended purpose. Never modify or alter  
machine for a purpose not intended by the  
manufacturer or serious injury may result!  
AWKWARD POSITIONS. Keep proper footing and  
balance at all times when operating machine.  
Do not overreach! Avoid awkward hand  
positions that make workpiece control difficult  
or increase the risk of accidental injury.  
USE RECOMMENDED ACCESSORIES. Consult  
this owner’s manual or the manufacturer for  
recommended accessories. Using improper  
accessories will increase the risk of serious  
injury.  
UNATTENDED OPERATION. Never leave machine  
running while unattended. Turn machine off  
and ensure all moving parts completely stop  
before walking away.  
CHILDREN & BYSTANDERS. Keep children and  
bystanders a safe distance away from work  
area. Stop using machine if children or  
bystanders become a distraction.  
MAINTAIN WITH CARE. Follow all maintenance  
instructions and lubrication schedules to  
keep machine in good working condition. An  
improperly maintained machine may increase  
the risk of serious injury.  
REMOVE ADJUSTING TOOLS. Never leave  
adjustment tools, chuck keys, wrenches, etc.  
in or on machine—especially near moving  
parts. Verify removal before starting!  
CHECK DAMAGED PARTS. Regularly inspect  
machine for damaged parts, loose bolts,  
mis-adjusted or mis-aligned parts, binding,  
or any other conditions that may affect safe  
operation. Always repair or replace damaged  
parts, wires, cords, or plugs before operating  
machine.  
SECURING WORKPIECE. When required, use  
clamps or vises to secure workpiece. A secured  
workpiece protects hands and frees both of  
them to operate the machine.  
FEED DIRECTION. Unless otherwise noted, feed  
work against the rotation of blades or cutters.  
Feeding in the same direction of rotation may  
pull your hand into the cut.  
MAINTAIN POWER CORDS. When disconnecting  
cord-connected machines from power, grab  
and pull the plug—NOT the cord. Pulling the  
cord may damage the wires inside. Do not  
handle the cord/plug with wet hands. Avoid  
cord damage by keeping it away from heated  
surfaces, high traffic areas, harsh chemicals,  
and wet or damp locations.  
GUARDS & COVERS. Guards and covers can  
protect you from accidental contact with  
moving parts or flying debris. Make sure  
they are properly installed, undamaged, and  
working correctly before using machine.  
EXPERIENCING DIFFICULTIES. If at any time you  
are experiencing difficulties performing the  
-8-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Additional Safety Instructions for Vertical Mills  
READ and understand this  
USE this and other machinery with caution  
entire instruction manual  
and respect. Always consider safety first,  
before using this machine.  
as it applies to your individual working  
Serious personal injury  
conditions. No list of safety guidelines can  
may occur if safety and  
be complete—every shop environment is  
operational information is  
different. Failure to follow guidelines could  
not understood and fol-  
result in serious personal injury, damage  
lowed. DO NOT risk your  
to equipment or poor work results.  
safety by not reading!  
MILL ASSEMBLY. Do not operate until unit is assembled and installed according to instructions.  
UNDERSTANDING CONTROLS. Make sure you understand the use and operation of all controls.  
SECURING WORKPIECE. Never hold a workpiece by hand for any type of machining operation. Hold your  
workpiece secure with a mill vise, step clamps, etc.  
SECURING CUTTING TOOLS. Make sure that the cutting tool is chucked or colleted properly. Cutting  
tools that are loose or not rotating correctly can come off and cause serious personal injury.  
CUTTING TOOL INSPECTION. Inspect drills and end mills for sharpness, chips, or cracks before each use.  
Replace dull, chipped, or cracked cutting tools immediately. Handle new cutting tools with care. Leading  
edges are very sharp and can cause lacerations.  
USING GUARDS. Make sure cover is closed and latched before turning the machine ON.  
CHUCK KEY SAFETY. Always remove your chuck key, draw bar wrench, and any service tools  
immediately after use.  
CLEARING CHIPS. Turn off machine and wait for cutting tool to come to a complete stop before clearing  
away chips. Chips are sharp. Use a brush to remove them.  
FEED AND SPEED RATES. Research the proper feed and speed rate for the material you are machining.  
Do not exceed these recommended rates.  
CHANGING SPINDLE DIRECTION. Never reverse motor direction while the spindle is in motion.  
TURNING OFF THE MILL. Allow the mill to come to a complete stop before leaving it unattended.  
SERVICING THE MILL. Make sure mill is turned OFF, unplugged, and the machine has come to a complete  
stop before servicing. Perform routine inspections and correct service related issues promptly.  
HAZARDOUS COOLANTS. Coolants used for machining may contain hazardous chemicals. Read and  
understand all user information on the coolant container and take any necessary precautions.  
-9-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
ELECTRICAL  
Availability  
Before installing the machine, consider the availability  
and proximity of the required power supply circuit. If an  
existing circuit does not meet the requirements for this  
machine, a new circuit must be installed. To minimize  
the risk of electrocution, fire, or equipment damage,  
installation work and electrical wiring must be done by  
a qualified electrician in accordance with all applicable  
codes and standards.  
Full-Load Current Rating  
Electrocution, fire, or equipment  
damage may occur if machine is not  
correctly grounded and connected to  
the power supply.  
The full-load current rating is the amperage a machine  
draws at 100% of the rated output power. On machines  
with multiple motors, this is the amperage drawn by the  
largest motor or sum of all motors and electrical devices  
that might operate at one time during normal operations.  
Full-Load Current Rating at 110V ................ 16 Amps  
Full-Load Current Rating at 220V ..................8 Amps  
For your own safety and protection of  
property, consult a qualified electrician  
if you are unsure about wiring practices  
or electrical codes in your area.  
The full-load current is not the maximum amount of amps  
that the machine will draw. If the machine is overloaded,  
it will draw additional amps beyond the full-load rating.  
If the machine is overloaded for a sufficient length of  
time, damage, overheating, or fire may result—especially  
if connected to an undersized circuit. To reduce the  
risk of these hazards, avoid overlovading the machine  
during operation and make sure it is connected to a  
power supply circuit that meets the requirements in the  
following section.  
-10-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Note: The circuit requirements listed in this  
manual apply to a dedicated circuit—where  
only one machine will be running at a  
time. If this machine will be connected to  
a shared circuit where multiple machines  
will be running at the same time, consult  
a qualified electrician to ensure that the  
circuit is properly sized for safe operation.  
Circuit Information  
A power supply circuit includes all electrical equipment  
between the breaker box or fuse panel in the building  
and the machine. The power supply circuit used for  
this machine must be sized to safely handle the full-  
load current drawn from the machine for an extended  
period of time. (If this machine is connected to a circuit  
protected by fuses, use a time delay fuse marked D.)  
Circuit Requirements for 110V  
This machine is prewired to operate on a 110V power  
supply circuit that has a verified ground and meets the  
following requirements:  
Nominal Voltage...................................110V/120V  
Cycle........................................................60 Hz  
Phase .............................................. Single-Phase  
Minimum Circuit Size ............................... 20 Amps  
Plug/Receptacle................................... NEMA 5-15  
Circuit Requirements for 220V  
This machine can be converted to operate on a 220V  
power supply (refer to Voltage Conversion later in this  
section). The intended 220V circuit must have a verified  
ground and meet the following requirements:  
Nominal Voltage...................................220V/240V  
Cycle........................................................60 Hz  
Phase .............................................. Single-Phase  
Minimum Circuit Size ............................... 15 Amps  
Plug/Receptacle................................... NEMA 6-15  
-11-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Grounding & Plug Requirements  
This machine MUST be grounded. In the event of certain  
malfunctions or breakdowns, grounding reduces the risk of  
electric shock by providing a path of least resistance for  
electric current.  
GROUNDED  
5-15 RECEPTACLE  
110V  
Grounding Prong  
For 110V operation: This machine is equipped with a  
power cord that has an equipment-grounding wire and a  
grounding plug (similar to the figure on the right). The  
plug must only be inserted into a matching receptacle  
(outlet) that is properly installed and grounded in  
accordance with all local codes and ordinances.  
5-15 PLUG  
Neutral Hot  
For 220V operation: The plug specified under “Circuit  
Requirements for 220V” on the previous page has a  
grounding prong that must be attached to the equipment-  
grounding wire inside the included power cord. The plug  
must only be inserted into a matching receptacle (similar  
to the figure on the right) that is properly installed  
and grounded in accordance with all local codes and  
ordinances.  
Figure 1. Typical 5-15 plug and receptacle.  
GROUNDED  
6-15 RECEPTACLE  
Current Carrying Prongs  
Improper connection of the equipment-grounding wire  
can result in a risk of electric shock. The wire with  
green insulation (with or without yellow stripes) is the  
equipment-grounding wire. If repair or replacement of  
the power cord or plug is necessary, do not connect the  
equipment-grounding wire to a live (current carrying)  
terminal.  
6-15 PLUG  
Grounding Prong  
Figure 2. Typical 6-15 plug and receptacle.  
Check with a qualified electrician or service personnel  
if you do not understand these grounding requirements,  
or if you are in doubt about whether the tool is  
properly grounded. If you ever notice that a cord or  
plug is damaged or worn, disconnect it from power, and  
immediately replace it with a new one.  
Serious injury could occur if you con-  
nect the machine to power before  
completing the setup process. DO  
NOT connect to power until instructed  
later in this manual.  
Extension Cords  
We do not recommend using an extension cord with this  
machine. If you must use an extension cord, only use it if  
absolutely necessary and only on a temporary basis.  
Voltage Conversion  
Extension cords cause voltage drop, which may damage  
electrical components and shorten motor life. Voltage  
drop increases as the extension cord size gets longer  
and the gauge size gets smaller (higher gauge numbers  
indicate smaller sizes).  
The voltage conversion MUST be performed  
by a qualified electrician. To perform the  
voltage conversion, install the correct plug  
and rewire the motor to the new voltage,  
according to the provided wiring diagram.  
If the diagram included on the motor  
conflicts with the one in this manual, the  
motor may have changed since the manual  
was printed. Use the diagram provided on  
the motor.  
Any extension cord used with this machine must contain a  
ground wire, match the required plug and receptacle, and  
meet the following requirements:  
Minimum Gauge Size .................................12 AWG  
Maximum Length (Shorter is Better) ................50 ft.  
-12-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
SET UP  
Unpacking  
The SHOP FOX® Model M1001 has been carefully pack-  
aged for safe transporting. If you notice the machine has  
been damaged, please contact your authorized SHOP  
FOX® dealer immediately.  
Inventory  
The following is a description of the main components  
shipped with the SHOP FOX® Model M1001. Lay the  
components out to inventory them.  
Wooden Box Contents (Figures 3 & 4)  
Qty  
A. Milling Machine ............................................1  
B. Toolbox......................................................1  
Figure 3. Model M1001.  
Toolbox Contents (Figure 4)  
Qty  
C. 3" Shell Mill with Arbor ...................................1  
D. Handwheels.................................................2  
E. Handwheel Handles .......................................4  
F. Drawbar with Locking Nut ...............................1  
G. Spare V-Belts ...............................................2  
H. 220V ON/OFF Switch......................................1  
I. Open End Wrenches 17/19mm & 12/14mm...........2  
J. T-Slot Bolts M12-1.75 x 40 ...............................2  
K. Screwdriver.................................................1  
L. Phillips Head Screwdriver ................................1  
M. Hex Wrenches 3, 4, 5, & 6mm ..........................4  
B
G
M
K
L
I
C
H
E
J
D
F
Inventory parts not shown:  
•
Power Feed Instruction Manual .........................1  
Figure 4. Toolbox contents.  
If any parts are missing, find the part number in the back  
of this manual and contact Woodstock International, Inc.  
at (360) 734-3482 or at tech-support@shopfox.biz  
NOTICE  
When ordering replacement parts, refer  
to the parts list and diagram in the back  
of the manual.  
SUFFOCATION HAZARD!  
Immediately discard all plastic bags  
and packing materials to eliminate  
choking/suffocation hazards for chil-  
dren and animals.  
-13-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Machine Placement  
Cleaning Machine  
•
•
Floor Load: Your vertical mill has a large  
weight load of 822 lbs. in a small footprint.  
We recommend placing this mill on a  
concrete floor.  
The table and other unpainted parts of your  
Vertical Mill are coated with a waxy grease that  
protects them from corrosion during shipment.  
Clean this grease off with a solvent cleaner or  
citrus-based degreaser. DO NOT use chlorine-  
based solvents such as brake parts cleaner or  
acetone—if you happen to splash some onto a  
painted surface, you will ruin the finish.  
Working Clearances: Consider existing and  
anticipated needs, size of material to be  
processed through the machine, and space  
for auxiliary stands, work tables or other  
machinery when establishing a location for  
your vertical mill (see Figure 5).  
NEVER use gasoline or  
other petroleum-based  
solvents to clean with.  
Most  
points, which make them  
extremely flammable.  
A risk of explosion and  
burning exists if these  
products are used. Serious  
personal injury may occur  
if this warning is ignored!  
•
•
Lighting: Lighting should be bright enough  
to eliminate shadow and prevent eye strain.  
have low flash  
Electrical: Electrical circuits must be  
dedicated or large enough to handle  
amperage requirements. Outlets must be  
located near each machine, so power or  
extension cords are clear of high-traffic  
areas. Follow local electrical codes for  
proper installation of new lighting, outlets,  
or circuits.  
60"  
ALWAYS work in well-  
ventilated areas far from  
possible ignition sources  
when using solvents to  
clean machinery. Many  
solvents are toxic when  
inhaled or ingested. Use  
care when disposing  
of waste rags and  
towels to be sure they  
DO NOT create fire or  
environmental hazards.  
41"  
Figure 5. M1001 minimum working clearances.  
USE helpers and power  
lifting equipment to lift  
this 6" x 26" Vertical Mill.  
Otherwise, serious per-  
sonal injury may occur.  
-14-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Mounting Mill on Shop  
Floor  
Although not required, it is recommend that you mount  
your new mill to the floor. Because this is an optional  
step and floor materials may vary, floor mounting  
hardware is not included. Generally, you can either  
bolt your machine to the floor or mount it on machine  
mounts. Both options are described below. Whichever  
option you choose, it will be necessary to use a precision  
level to level your mill (see Figures 6-8).  
Bolting to Concrete Floors  
Lag shield anchors with lag bolts and anchor studs are  
two predominate methods for anchoring an object to a  
concrete floor. We suggest you research the many options  
and methods for mounting your mill and choose the best  
that fits your specific application.  
Figure 6. Typical lag shield anchor and lag  
bolt.  
Using Machine Mounts  
Using machine mounts gives the advantage of fast leveling  
and vibration reduction. The large size of the foot pads  
distributes the weight of the machine to reduce strain on  
the floor.  
NOTICE  
Anchor studs, as shown in Figure 7, are stronger and  
more permanent alternatives to lag shield anchors;  
however, they will stick out of the floor, which may  
cause a tripping hazard if you decide to move your  
machine at a later point.  
Figure 7. Typical anchor stud.  
Figure 8. Machine mount example.  
-15-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Assembly  
The Model M1001 comes fully assembled from the factory  
with the exception of one of the longitudinal handwheels  
and the cross handwheel. The head has been rotated to  
reduce the overall dimension of the shipping crate.  
Nuts 2 & 3  
Hidden from  
View  
Headstock Adjustment  
Loosen the three nuts at the column and rotate the  
headstock to the "0" position on the column scale (see  
Figure 10).  
Handle Installation  
The longitudinal and cross handwheels shown in Figure  
11 need to be installed. The handwheel handles will  
need to be installed on all the handwheels. Attach  
the handwheels and handles with the hex wrench,  
screwdriver, and hardware provided.  
Figure 10. Headstock lock nuts.  
Longitudinal  
Handwheel  
Cross  
Handwheel  
Drawbar  
Open the top cover and insert the drawbar into the  
splined spindle located in the center of the front cone  
pulley (see Figure 12).  
Single Shot Lubrication  
Knee Feed  
Unscrew the filler cap and fill the reservoir with non-  
detergent SAE-20 or similar way oil. Manually pump the  
lever until resistance from the oil pressure is felt (see  
Figure 9).  
Figure 11. Handwheel locations.  
Drawbar  
Figure 12. Drawbar location.  
Figure 9. Single shot lubrication system.  
-16-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Spindle Controls  
Figure 13 shows the location of the ON/OFF buttons and  
the SPINDLE DIRECTION toggle for the Model M1001.  
ON/OFF  
•
The ON/OFF buttons control power to the spindle.  
Spindle Direction  
•
The SPINDLE DIRECTION toggle will change the  
direction the spindle rotates. DO NOT change spindle  
rotation until spindle has come to a complete stop!  
Test Run  
Complete this process once you have familiarized yourself  
with all instructions in this manual and you have made  
sure the machine is completely lubricated as described in  
Lubrication onon page 27Pon page 27. The purpose of  
the test run is to make sure the motor is working properly  
before proceeding.  
Figure 13. Spindle controls.  
NOTICE  
Follow spindle break in procedures  
on Page on page 24 after the test run  
and before performing any operations  
with this machine! Failure to follow the  
break-in procedures included in this  
manual may lead to shortened tool life  
and may void warranty.  
To begin the test run procedure, do these steps:  
1. Make sure there are no obstructions around or  
underneath the spindle.  
2. Set the mill to the slowest RPM. See Page on page  
23 for adjusting RPM.  
3. Put on safety glasses, and make sure any bystanders  
are wearing safety glasses and are out of the way.  
4. Plug the machine into the power outlet and push the  
ON/OFF switch to turn the mill ON, but make sure  
that your hand stays over the switch. The mill should  
run smoothly, with little or no vibration or rubbing  
noises.  
• If you hear squealing or grinding noises, turn the  
machine OFF immediately. Wait for the mill to  
stop moving, unplug the machine, and correct any  
problems before further operation.  
• If the source of an unusual noise or vibration is not  
readily apparent, contact our technical support  
for help at (360) 734-3482 or contact us online at  
tech-support@shopfox.biz.  
-17-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
OPERATIONS  
General  
The Model M1001 will perform many types of operations  
that are beyond the scope of this manual. Many of these  
operations can be dangerous or deadly if performed incor-  
rectly.  
The instructions in this section are written with the under-  
standing that the operator has the necessary knowledge  
and skills to operate this machine. If at any time you  
are experiencing difficulties performing any operation,  
stop using the machine!  
READ and understand this entire instruc-  
tion manual before using this machine.  
Serious personal injury may occur if  
safety and operational information is not  
understood and followed. DO NOT risk  
your safety by not reading!  
If you are an inexperienced operator, we strongly recom-  
mend that you read books, trade articles, or seek training  
from an experienced vertical mill operator before per-  
forming any unfamiliar operations. Above all, your safety  
should come first!  
Positioning Spindle Head  
The spindle head can be rotated vertically 45˚ both ways,  
and can rotate horizontally on the column 45˚ in both  
directions.  
To rotate the spindle head vertically, do these steps:  
1. UNPLUG THE MILL!  
Always wear safety glasses when oper-  
ating the mill. Failure to comply may  
result in serious personal injury.  
2. Make sure the spindle is stopped and the work area  
is free from obstructions before proceeding.  
3. Loosen the four nuts that lock the headstock in place  
with a 17mm wrench (see Figure 14 on next page).  
4. Rotate the headstock to the desired angle.  
5. Tighten the spindle locking nuts.  
Note: Additional setup tools should be used to determine  
the precise angle of the spindle head.  
DO NOT investigate problems or adjust  
the mill while it is running. Wait until  
the machine is turned off, unplugged  
and all working parts have come to a  
complete stop before proceeding!  
-18-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
To rotate the spindle head horizontally, do these  
steps:  
Vertical Lock Nuts  
1. UNPLUG THE MILL!  
2. Make sure the spindle is stopped and the work area  
is free from obstructions before proceeding.  
3. Using a 17mm wrench, loosen the three locking nuts  
shown in Figure 14.  
4. Push or pull the spindle head to swivel it to the  
desired position. Use the scale located on the  
column to set the angle desired.  
Horizontal Lock Nuts  
Figure 14. Vertical and horizontal  
5. Tighten the three nuts to lock the headstock in  
headstock lock nuts.  
position.  
Table Travel  
The table can be moved in 3 axes. Each axis is  
independently controlled by a handle or handwheel. The  
longitudinal travel has the added feature of a power  
feed, which will be explained in more detail later. Each  
handle or handwheel has a graduated dial to accurately  
position the workpiece in relation to the cutting tool.  
Each axis has the ability to be locked in position. Locking  
the axis in place will help keep workpiece vibration to a  
minimum.  
Longitudinal Locks  
Figure 15. Longitudinal locks.  
Longitudinal Feed Control  
The longitudinal feed is controlled by two handwheels,  
one at each end of the table, and can be locked in  
position by the two locks at the front of the table (see  
Figure 15).  
Knee Lock  
Cross Feed  
The cross feed is controlled by the center handwheel,  
and can be locked in position by the lock under the left  
side of the mill table (see Figure 16).  
Knee Feed  
Cross Lock  
The knee feed is controlled by one handle, just off center  
at the front of the machine. The Model M1001 has one  
knee feed lock on the left side of machine next to the  
single shot pump, where the knee meets the ways (see  
Figure 16).  
Figure 16. Cross and knee locks.  
-19-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Graduated Dials  
The table handwheels and the knee handle have  
graduated dials. Each mark represents 0.001" of  
movement and one full revolution equals 0.100" The  
graduated dials float and can be indexed or "zeroed" by  
loosening the knurled head thumb screw, rotating the  
graduated dial to "0", and securing the setting with the  
knurled head thumb screw (see Figure 17).  
Example:  
Suppose you want to drill a series of holes with 1/2"  
centers (0.500"). After locating the first hole placement  
and drilling, you would zero the graduated dial of the  
appropriate axis, set the knurled head thumb screw,  
move the table 0.500" in the appropriate direction and  
drill the next hole.  
Figure 17. Graduated dial.  
Power Feed Controls  
This mill comes equipped with a power feed on the  
longitudinal travel. The power feed has the following  
controls (see Figure 18 for items A–D, and see Figure 19  
for items E–F): For additional information, please refer to  
the power feed manual supplied with this mill.  
B
C
A
A. Right/Left Feed Selector—Switch the lever to the  
left or the right for the desired travel direction.  
The table should come to a complete stop before  
changing directions.  
D
B. Rapid Speed Switch—Pressing this switch will cause  
the table to feed at its maximum rate until it is  
released.  
Figure 18. Power feed controls.  
C. Feed Setting Dial—Setting from 0 (no travel) to 10  
F
(fastest travel).  
D. ON/OFF Switch—Delivers power to the power feed.  
E. Limit Switch—Stops the power feed when it makes  
E
contact with the power feed stops.  
F. Power Feed Stops—Adjustable stops trigger the  
limit switch and shuts OFF the power feed when the  
table is at the end of its travel.  
Figure 19. Limit switch and power feed  
stops.  
-20-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Quill Travel  
Quill Feed Control  
Pinch Bolt  
The quill feed is controlled by the quill feed handle  
shown in Figure 20. The handle allows the mill to  
operate as a drill.  
To use the quill feed handle, do these steps:  
1. Pull the quill feed handle (see Figure 20) forward  
to feed the quill down towards the workpiece.  
The quill feed handle is spring loaded to assist in  
returning the handle to the upmost vertical position.  
Quill Lock  
Quill Feed Handle  
2. Lock the quill in place at any depth by tightening  
the quill feed handle lock shown in Figure 20.  
Figure 20. Quill feed controls.  
Note: When the quill feed is not in use, return it to  
the upmost position and lock in place. This will help  
maintain mill rigidity and accuracy.  
Quill Clutch Knob  
3. Adjust the position of the handle by loosening the  
pinch bolt on the quill shaft and then tightening  
when the handle is in the desired position.  
Micro-feed Depth Adjustment  
The micro-feed handwheel is used to accurately control  
the quill depth (see Figure 21).  
Micro-feed Handwheel  
To use the micro-feed handwheel, do these steps:  
Figure 21. Micro-feed controls.  
1. Turn the mill OFF and allow the spindle to come to a  
complete stop.  
2. Tighten the quill clutch knob.  
3. Turn the micro-feed handwheel (see Figure  
21) clockwise to feed the quill down or  
counterclockwise to feed the quill up.  
-21-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Determining Needed RPM  
Before changing speeds, you must first determine the  
best RPM to use with the material and diameter of your  
cutting tool. Using this determined RPM, you can then set  
the mill to match that speed.  
Cutting Speeds for High Speed Steel  
(HSS) Cutting Tools*  
Workpiece Material  
Aluminum & Alloys  
Brass & Bronze  
Copper  
Cutting Speed (SFM)  
300  
150  
100  
80  
To determine the RPM needed for your workpiece, do  
these steps:  
Cast Iron, soft  
Cast Iron, hard  
Mild Steel  
1. Use the chart in Figure 22 to determine the cutting  
50  
speed for your workpiece material.  
90  
Cast Steel  
80  
2. Measure the diameter of your cutting tool in inches.  
Alloy Steel, hard  
Tool Steel  
40  
50  
3. Use the following formula in Figure 23 to determine  
Stainless Steel  
Titanium  
60  
the best RPM for your operation.  
50  
Note: Always round to the closest RPM given on the  
spindle speed chart.  
Plastics  
300-800  
300-500  
Wood  
*For carbide cutting tools, double the cutting  
speed. These values are a guideline only. Refer to  
the current edition of MACHINERY'S HANDBOOK for  
more detailed information.  
Example 1  
You have a piece of aluminum stock, and you are  
using a 1/2" diameter HSS cutting tool.  
Figure 22. Cutting speed chart for HSS  
Step 1:  
cutting tools.  
300 (SFM from chart) x 4 = 1200  
Step 2:  
1200 / .5" (Diameter of cutting tool) = 2400 RPM  
Result:  
The best speed for this workpiece is 2400 RPM.  
Example 2  
Figure 23. Formula to determine required  
You have a piece of stainless steel, and you are  
using a 1" diameter carbide cutting tool.  
RPM.  
Step 1:  
60 (SFM from chart) x 2 (for carbide tool) = 120  
Step 2:  
120 (determined SFM) x 4 = 480  
Step 3:  
480 / 1" (Diameter of cutting tool) = 480 RPM  
Result:  
The best speed for this workpiece is 480 RPM.  
-22-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Setting RPM  
Setting the RPM on the Model M1001 involves placing the  
V-belts on the pulleys as shown in the spindle speed chart  
below.  
Motor Release Lever  
To set the spindle speed, do these steps:  
1. Examine the Spindle Speed Chart in Figure 24 to  
find the closest match to your needed RPM.  
2. UNPLUG THE MILL!  
3. Open the pulley cover.  
4. Loosen the motor release lever and move the motor  
toward the spindle to loosen the tension on the  
V-belts.  
Figure 25. Applying tension to V-belts.  
5. Move the belts to the appropriate pulley  
combinations as shown on the spindle speed chart  
below.  
Failure to follow RPM and feed rate  
guidelines may threaten operator  
safety from ejected parts or broken  
tools.  
6. Tension the V-belts by pulling the motor back and  
locking the motor release lever (see Figure 25).  
7. Close the pulley cover and plug in the mill.  
NOTICE  
Spindle Pulley  
Motor Pulley  
III  
Idler Pulley  
Failure to follow RPM and feed rate  
guidelines will put undue strain on  
moving parts, shorten tool life, and  
create poor workpiece results.  
A
B
I
C
II  
D
Spindle RPM  
B
A
C
D
I
730  
360  
240  
520  
II  
1600  
2760  
1280  
2220  
III  
1320  
Figure 24. M1001 Spindle speed chart in RPMs.  
-23-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Spindle Break-in  
Procedure  
Complete this process once you have familiarized  
yourself with all instructions in this manual  
and have made sure the machine is completely  
lubricated.  
5. Turn ON the spindle in the forward rotation  
and let it run for a minimum of 10 minutes.  
6. Turn the spindle OFF, wait for the spindle  
to come to a complete stop.  
7. Set the SPINDLE DIRECTION toggle to the  
reverse position and turn the spindle ON.  
Run the spindle in the reverse direction for  
10 minutes.  
NOTICE  
The spindle break-in procedure is important  
for ensuring long life and trouble-free per-  
formance from your mill. Failure to perform  
this proceedure can shorten the life of your  
machine and void your warranty.  
8. Repeat these steps for each RPM setting.  
To break-in the spindle, do these steps:  
1. Make sure the mill has been properly  
lubricated.  
2. Make sure there are no obstructions around  
or underneath the spindle.  
3. Set the spindle speed to the lowest RPM.  
4. Set the SPINDLE DIRECTION toggle to the  
forward position.  
-24-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Installing Tools  
To load a tool in the spindle, do these steps:  
1. UNPLUG THE MILL!  
Drawbar  
2. Turn the mill OFF, allow it to come to a complete  
stop and unplug the mill.  
3. Clean any debris from the spindle opening.  
4. Insert the tool holder or a collet into the spindle.  
5. Rotate the holder until the groove lines up with the  
key and the holder slides into the spindle.  
6. Use a wrench to tighten the drawbar (see Figure 26)  
Figure 26. Drawbar location.  
until the tool is secure in the spindle.  
Note: Do not overtighten the drawbar.  
Overtightening makes collet removal difficult and  
causes unnecessary wear to the draw bar threads,  
collet, and the spindle taper.  
NOTICE  
DO NOT overtighten the drawbar.  
Overtightening makes collet removal  
difficult and causes damage to the  
drawbar threads, collets, and spindle  
taper.  
7. Close the pulley cover and clear all items away from  
the cutting tool before turning the mill ON.  
Removing Cutting Tools  
NOTICE  
To remove cutting tools, do these steps:  
When not in use, always remove  
collets and cutting tools from spindle  
taper. Failure to do so may cause the  
collet to seize and be very hard to  
remove later.  
1. UNPLUG THE MILL!  
2. Make sure the spindle is turned OFF and the quill is  
at the upmost position.  
3. Use a brush to remove any debris or chips from the  
tool and the tool holder/arbor.  
4. Use a wrench to loosen the drawbar from the tool.  
5. Once the tool is loosened, support the cutter with  
a gloved hand, and strike the drawbar with a dead  
blow hammer or rubber mallet to release the tool  
holder from the spindle.  
Note: DO NOT strike the drawbar if it is completely  
unscrewed from the tool. This can damage the  
threads on the drawbar and the tool.  
6. Finish unscrewing the drawbar by hand.  
7. Clean any debris from the spindle opening area.  
-25-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
MAINTENANCE  
General  
Regular periodic maintenance on your SHOP FOX®  
mill will ensure optimum performance. Make a habit of  
inspecting your mill each time you use it.  
Check for the following conditions and repair or  
replace when necessary:  
•
•
•
•
•
•
•
Loose chucks and arbors.  
Loose vices or clamps.  
Loose mounting bolts.  
Worn switch and safety shut off features.  
Worn or damaged cords and plugs.  
Damaged V-belt.  
Any other condition that could hamper the safe  
operation of this machine.  
MAKE SURE that your machine is  
unplugged during all maintenance pro-  
cedures! If this warning is ignored, seri-  
ous personal injury may occur.  
A thorough cleaning, on a regular basis, will increase the  
machine durability and efficiency by removing chips and  
grime that can gum up moving parts.  
A regular application of a protective spray coating will  
keep the table and other bare metal parts from rusting  
and pitting.  
Cleaning  
Cleaning the Model M1001 is relatively easy. Sweep excess  
metal chips from the table and ways, and wipe off the  
remaining waste with a dry cloth. If any coolant is left on  
the table, wipe it up with a rag. Treat all unpainted cast  
iron and steel with a non-staining lubricant after cleaning.  
Table and Base  
Protect the unpainted cast iron surfaces by wiping them  
clean after every use—this ensures moisture does not  
remain on bare metal surfaces.  
Keep exposed cast iron rust-free with regular applications  
of surface lubricants designed for cast iron.  
Remove vices, clamps, rotary tables, etc. after use so  
moisture cannot be trapped between the components  
and cause rust.  
-26-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Lubrication  
Power Feed  
The power feed uses SAE 40 oil and should not need to  
be changed unless the unit is being repaired.  
Knee Screw  
Single Shot Lubrication System  
Use the single shot lubrication system to oil the ways, the  
crossfeed screw, and the longitudinal screw by pumping  
the handle on the reservoir 2-4 times each day (see  
Figure 27). Fill the reservoir regularly with ISO 68 or SAE  
20 weight machine oil.  
Figure 27. Single shot lubrication system.  
Knee Elevating Screw  
Apply liberal amounts of lithium or graphite based grease  
using a brush or shop rag to the entire length of the knee  
elevating screw.  
Drawbar Splines  
Drawbar Splines  
Place five drops of ISO 68 or SAE 20 weight machine oil  
on the splines around the drawbar once a week. This is  
accomplished by moving the quill all the way down and  
locking it in place. Apply the oil to the splines on the  
back side of the drawbar hole. Next, run the quill through  
complete motion a couple of times to lubricate splines  
(see Figure 28).  
Figure 28. Drawbar splines.  
-27-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Maintenance Schedule  
Daily:  
•
•
•
•
•
Pump handle of the one shot lubrication system 2-4 times.  
Clean machine to remove debris.  
Make sure table/vise is clean and free of metal chips.  
Clean spindle openings before inserting tools.  
Check for any unsafe conditions.  
Weekly:  
•
•
•
Place five drops of oil on the drawbar splines.  
Thoroughly clean the machine ways to remove chips and debris.  
Clean and grease the longitudinal, cross, and knee lead screws.  
Monthly:  
•
•
Clean/vacuum dust buildup from the motor.  
Check mill for level, correct if necessary.  
Every Six Months:  
Inspect belts for wear, and replace as needed.  
•
Maintenance Notes  
DATE  
MAINTENANCE PERFORMED  
-28-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
SERVICE  
General  
This section covers the most common service adjustments  
or procedures that may need to be made during the life  
of your machine. Always disconnect your machine from  
the power source before performing any service!  
If you require additional machine service not included  
in this section, please contact Woodstock International  
Technical Support at (360) 734-3482 or send e-mail to:  
tech-support@shopfox.biz.  
Figure 29. Cross gib screw.  
Figure 30. Longitudinal gib screw.  
Figure 31. Knee gib screw.  
MAKE SURE that your machine is unplugged during all  
service procedures! If this warning is ignored, serious  
personal injury may occur.  
Gibs  
The gibs are pre-adjusted at the factory and should not  
need further adjustment until many hours of machine use,  
if ever. If the movement seems too tight, make sure that  
the locks are fully released, ways are free of chips and  
debris and are thoroughly lubricated with oil.  
When adjusting the gibs, the goal is to take out  
unnecessary play in the table and cross slide without  
causing the slides to bind. Loose gibs may cause poor  
finishes on the workpiece and may cause undue wear on  
the slide. Over-tightening may cause premature wear to  
the gib.  
Adjust the gibs by a combination of loosening or  
tightening the adjustment screws until a slight drag is felt  
while moving the table/knee along the dovetail slides.  
There are two adjustment screws, one on each end of the  
gib (see Figures 29-31 for the locations of the adjustment  
screws). The chip wiper guards must be removed to  
access some of the gib adjustment screws.  
-29-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Adjusting Backlash  
Backlash is the amount of play found in a leadscrew.  
It can be found by turning the cross slide handwheel  
in one direction, and then turning the handwheel the  
other direction. When the cross slide begins to move, the  
backlash has been taken up.  
Adjustment Cap Screws  
Leadscrews are adjusted for backlash at the factory  
and should not need any adjustment for many hours of  
machine use, if ever. Keeping a clean and well lubricated  
machine will ensure long leadscrew life.  
To adjust the backlash, do these steps:  
Longitudinal Nut  
Longitudinal Feed Adjustment  
1. Slightly tighten the two cap screws on the  
longitudinal nut (see Figure 32). DO NOT  
overtighten.  
Figure 32. Longitudinal nut.  
2. Rotate the handwheel in both directions to see if  
backlash has been reduced or eliminated. There  
should only be a slight drag when turning the  
handwheel.  
Cross Nut  
Note: If the cap screws are too tight, it will  
cause excessive wear to the longitudinal nut and  
leadscrew, which could lead to costly repairs.  
Adjustment Cap Screws  
Crossfeed Adjustment  
1. Slightly tighten the two cap screws on the cross nut  
(see Figure 33). DO NOT overtighten.  
Figure 33. Cross nut.  
2. Rotate the handwheel in both directions to see if  
backlash has been reduced or eliminated. There  
should only be a slight drag when turning the  
handwheel.  
Note: If the cap screws are too tight, it will cause  
excessive wear to the cross nut and leadscrew, which  
could lead to costly repairs.  
-30-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Electrical Safety Instructions  
These pages are current at the time of printing. However, in the spirit of improvement, we may  
make changes to the electrical systems of future machines. Study this diagram carefully. If you notice  
differences between your machine and these wiring diagrams, call Woodstock International Technical  
Support at (360) 734-3482.  
1. SHOCK HAZARD. Working on wiring that is  
connected to a power source is extremely  
dangerous. Touching electrified parts will  
result in personal injury including but not  
limited to severe burns, electrocution,  
or death. Disconnect the power from  
the machine before servicing electrical  
components!  
5. MOTOR WIRING. The motor wiring shown  
in these diagrams is current at the time  
of printing, but it may not match your  
machine. Always use the wiring diagram  
inside the motor junction box.  
6. MODIFICATIONS. Using aftermarket parts or  
modifying the wiring beyond what is shown  
in the diagram may lead to unpredictable  
results, including serious injury or fire.  
2. QUALIFIED ELECTRICIAN. Due to the  
inherent hazards of electricity, only a  
qualified electrician should perform wiring  
tasks on this machine. If you are not a  
qualified electrician, get help from one  
before attempting any kind of wiring job.  
7. CAPACITORS/INVERTERS. Some capacitors  
and power inverters store an electrical  
charge for up to five minutes after being  
disconnected from the power source. To  
avoid being shocked, wait at least this long  
before working on these components.  
3. WIRE CONNECTIONS. All connections must  
be tight to prevent wires from loosening  
during machine operation. Double-check all  
wires disconnected or connected during any  
wiring task to ensure tight connections.  
8. ELECTRICAL REQUIREMENTS. You MUST  
follow the electrical requirements at the  
beginning of this manual when connecting  
your machine to a power source.  
4. WIRE/COMPONENT DAMAGE. Damaged  
wires or components increase the risk of  
serious personal injury, fire, or machine  
damage. If you notice that any wires or  
components are damaged while performing  
a wiring task, replace those wires or  
9. EXPERIENCING DIFFICULTIES. If you are  
experiencing difficulties understanding  
the information included in this section,  
contact our Technical Support at (360) 734-  
3482.  
components before completing the task.  
WIRING DIAGRAM COLOR KEY  
BLACK  
WHITE  
GREEN  
RED  
BLUE  
YELLOW  
LIGHT  
BLUE  
The photos and diagrams  
included in this section are  
best viewed in color. You  
can view these pages in  
color at www.shopfox.biz.  
YELLOW  
GREEN  
PURPLE  
BROWN  
GRAY  
BLUE  
WHITE  
TUR-  
QUOISE  
ORANGE  
PINK  
-31-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Electrical Parts Identification  
DZ47LE C32 Contactor  
Read  
Page 31  
DZ47 Contactor  
STOP  
Before  
Wiring  
Move wire to posi-  
tion A for 220V  
operation.  
A
Transformer  
Terminal Bar  
Wiring Box  
Figure 34. M1001 Electrical panel.  
-32-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Wiring Diagram  
265 VAC 150�F Capacitor  
Contactor  
2A  
110V  
110V  
(220V)  
(220V)  
Starter  
24V,40W  
U
1
V2  
Reverse  
Switch  
Z2  
Motor  
Z
1
400 VAC 20 ±5 �F Capacitor  
Figure 37. M1001 Wiring schematic.  
Figure 35. Motor wiring box currently  
wired for 110V.  
Read  
Page 31  
Jumpers  
STOP  
Black  
Black  
Before  
Wiring  
Red  
Red  
110V wiring for motor  
Black  
Jumpers  
Black  
Red  
Red  
220V wiring for motor  
Figure 36. Motor wiring for 110V or 220V.  
Also refer to Figure 37.  
NOTICE  
If you find the spindle rotates in the oppo-  
site direction as indicated by the switch,  
reverse the position of the two black power  
wires.  
-33-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Troubleshooting  
This section covers the most common problems. WARNING! DO NOT make any adjust-  
ments until the mill is unplugged and all moving parts have come to a complete stop.  
SYMPTOM  
POSSIBLE CAUSE  
CORRECTIVE ACTION  
Motor will not start.  
1. Tripped circuit breaker or relay  
inside machine wiring box or power  
source breaker box.  
1. Reset circuit breaker by flipping switch on then  
off then back on. Reset relay by pressing the reset  
button located on the face.  
2. Low voltage.  
3. Open circuit in motor or loose  
connections.  
2. Check power supply for proper voltage.  
3. Inspect all lead connections on motor and magnetic  
switch for loose or open connections.  
4. Replace switch.  
4. Switch at fault.  
5. Faulty start capacitor.  
5. Replace start capacitor.  
Fuses or circuit breakers  
trip open.  
1. Short circuit in line cord or plug.  
1. Inspect cord or plug for damaged insulation and  
shorted wires and replace extension cord.  
2. Inspect all connections on motor for loose or  
shorted terminals or worn insulation.  
2. Short circuit in motor or loose  
connections.  
3. Incorrect fuses or circuit breakers  
in power supply.  
3. Install correct fuses or circuit breakers.  
Motor overheats.  
1. Motor overloaded.  
2. Air circulation through the motor  
restricted.  
1. Reduce load on motor.  
2. Clean out motor to provide normal air circulation.  
Tool slips in collet.  
1. Collet is not fully drawn up into  
spindle taper.  
1. Snug up draw bar.  
2. Wrong size collet.  
2. Measure tool shank diameter and match with  
appropriate diameter collet.  
3. Debris in collet or in spindle taper. 3. Remove all oil and debris from collet and spindle  
taper.  
4. Taking too big of a cut.  
4. Lessen depth of cut and allow chips to clear.  
Breaking tools or cutters.  
Machine is loud when  
cutting. Overheats or bogs 2. Dull cutting tools.  
down in the cut.  
1. RPM and or feed rate is too fast.  
2. Cutting tool getting too hot.  
3. Taking too big of a cut.  
1. Use tables to set correct RPM and feed rates.  
2. Use cutting fluid or oil for appropriate application.  
3. Lessen depth of cut and allow chips to clear.  
1. Excessive depth of cut.  
1. Decrease depth of cut.  
2. Use sharp cutting tools.  
Workpiece vibrates or  
chatters during operation. 2. Spindle lock not tight.  
1. Table locks not tight.  
1. Tighten down table locks.  
2. Tighten spindle lock.  
3. Workpiece not securely clamped to 3. Check that clamping is tight and sufficient for the  
table or into mill vice.  
4. RPM and feed rate too high.  
job. Make sure mill vice is tight to the table.  
4. Use appropriate RPM and feed for the job.  
Table hard to move.  
1. Table locks are tightened down.  
1. Make sure table locks are fully released.  
2. Chips have loaded up on bedways. 2. Frequently clean away chips that load up during  
milling operations.  
3. Bedways are dry and in need of  
lubrication.  
3. Lubricate bedways and handles.  
4. Longitudinal stops are interfering.  
4. Check to make sure that stops are floating and not  
hitting the center stop.  
5. Gibs are too tight.  
5. Loosen gib screw(s).  
Bad surface finish.  
1. Wrong RPM or feed rate.  
2. Dull cutting tool or poor cutting  
tool selection.  
1. Adjust for appropriate RPM and feed rate.  
2. Sharpen cutting tool or select a better cutting tool  
for the intended operation.  
3. Wrong rotation of cutting tool.  
3. Check for proper cutting rotation for cutting tool.  
-34-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Headstock Assembly  
151  
152  
153  
2
151  
152  
56  
71  
57  
71  
58  
70  
54  
168  
39  
41  
38  
40  
55  
39  
73-4  
169  
59  
72  
73-3  
73-5  
10  
137  
61  
69  
35  
36  
11  
46  
9
37  
66  
13  
138  
73  
17  
50  
67  
4
48  
63  
47  
62 65  
16  
60  
15  
70  
53  
22  
73-2  
73-1  
128  
121  
14  
68  
70  
12  
49  
49  
42  
19  
23  
26  
51  
21  
172  
27  
28  
20  
45  
24  
53  
25  
18  
53  
34  
170  
31  
32  
33  
52  
136  
3
8
5
44  
43  
29  
171  
30  
6
113  
7
13  
-35-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Base Assembly  
84  
83  
130  
144  
127  
86  
85  
79  
126  
125  
75  
128  
77  
119  
143  
76  
91  
90  
89  
77  
78  
92  
81  
13  
130  
84  
85  
128  
104  
127  
82  
91  
98  
136  
80  
103  
86  
93  
127  
105  
80  
122  
120  
144  
90  
131  
94  
129  
106  
96  
102  
87  
88  
99  
127  
110  
108  
132  
133  
49  
125  
97  
131  
138  
123  
128  
144  
84  
85  
83  
120  
133  
109  
95  
128  
122  
100  
115  
88  
87  
86  
86  
80  
83  
157  
144  
139  
67  
164  
117  
80  
74  
163  
122  
141  
135  
110  
120  
120  
166  
165  
159  
160  
161  
118  
138  
162  
111  
134  
140  
69  
158  
142  
123  
112  
139  
173  
174  
72  
114  
148  
149  
154  
175  
167  
155  
150  
156  
147  
146  
-36-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Machine Parts Lists  
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
1
2
3
4
5
6
7
8
XM1001001  
VERTICAL MILLING HEAD  
BELT HOUSING COVER  
QUILL  
INT RETAINING RING 75MM  
LOCK WASHER 30MM  
VERTICAL SPINDLE  
COVER  
BEARING ADJUSTING NUT  
SPINDLE SLEEVE  
PULLEY LOCKING NUT  
SPINDLE PULLEY  
QUILL PINION SHAFT  
PHP HD SCREW M5-.8 X 10  
CLUTCH WORM GEAR  
CLUTCH  
CLUTCH ADJUSTING NUT  
CLUTCH COVER  
PINION SHAFT SEAT  
HANDLE  
SHAFT COLLAR  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
65  
66  
67  
68  
69  
70  
71  
72  
73  
XM1001050  
XM1001051  
XM1001052  
XPSB28M  
COIL SPRING  
COIL SPRING  
INT RETAINING RING 19MM  
CAP SCREW M6-1 x 15  
SWIVEL ARM  
XM1001002  
XM1001003  
XPR67M  
XPLW15M  
XM1001006  
XM1001007  
XM1001008  
XM1001009  
XM1001010  
XM1001011  
XM1001012  
XPS09M  
XM1001014  
XM1001015  
XM1001016  
XM1001017  
XM1001018  
XM1001019  
XM1001020  
XM1001021  
XM1001022  
XM1001023  
XM1001024  
XM1001025  
XM1001026  
XM1001027  
XM1001028  
XM1001029  
XM1001030  
XM1001031  
XM1001032  
XM1001033  
XM1001034  
XPB09M  
XM1001054  
XM1001055  
XM1001056  
XM1001057  
XM1001058  
XM1001059  
XM1001060  
XM1001061  
XM1001062  
XM1001063  
XM1001064  
XM1001066  
XM1001067  
XM1001068  
XPVA35  
SWIVEL STUD  
INT RETAINTING RING 35MM  
PULLEY PIVOT STUD  
V-BELT PULLEY  
V-BELT PULLEY  
MOTOR MOUNT  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
MOTOR SUSPENDING PIVOT  
MOTOR MOUNT  
BELT TENSIONING LOCK SCREW  
BELT TENSIONING SPRING  
VERTICAL HEAD ADAPTER  
STUD M12-1.75 X 35  
FLAT WASHER 10MM  
V-BELT A-35 4L350  
HEX NUT ACORN M12-1.75  
BALL BEARING 6003Z  
V-BELT A-31 4L310  
MOTOR 1.5 HP 4 POLE-1725  
XPN26M  
XP6003  
XPVA31  
XM1001073  
HAND LEVER  
WORM SHAFT  
WORM SHAFT SLEEVE  
BEARING LOCKNUT M14 x 1.5  
DIAL  
DIAL POSITIONING SCREW  
HANDWHEEL  
73-1 XM1001073-1 MOTOR COVER  
73-2 XM1001073-2 MOTOR FAN  
73-3 XPC20A  
73-4 XPC150A  
CAPACITOR 20MFD 400V  
CAPACITOR 150MFD 250VAC  
HANDLE  
73-5 XM1001073-5 JNCTN BOX & CPCTR COVER  
QUILL LOCKING BLOCK  
QUILL LOCKING BOLT  
QUILL STOP MICRO SCREW  
MICROMETER NUT  
QUILL MICRO STOP NUT  
QUILL STOPPER  
HEX HEAD BOLT M8-1.25 x 20  
FLAT WASHER 8MM  
DRAW BAR  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
90  
91  
92  
93  
94  
XM1001074  
XM1001075  
XM1001076  
XM1001077  
XM1001078  
XM1001079  
XM1001080  
XM1001081  
XPSB38M  
XM1001083  
XM1001084  
XM1001085  
XM1001086  
XM1001087  
XM1001088  
XM1001089  
XM1001090  
XM1001091  
XM1001092  
XM1001093  
XM1001094  
COLUMN  
TABLE  
TABLE GIB  
GIB ADJUSTING SCREW  
LONGITDNL BEARING BRACKET  
LONGITUDINAL LEAD SCREW  
BEARING NUT M20 x 15  
LONGITUDINAL FEED NUT  
CAP SCREW M5-.8 x 25  
DIAL  
DIAL POSITIONING SCREW  
HANDWHEEL  
HANDWHEEL HANDLE  
LONGITDNL ADJUSTING SCREW  
ADJUSTING SCREW SLEEVE  
TABLE STOPPER  
XPW01M  
XM1001037  
XM1001038  
XPS09M  
XM1001040  
XPN06M  
XM1001042  
XP7207  
XP6007ZZ  
XP6206  
C5 x 15 RIVET  
PHL HD SCREW M5-.8 x 10  
COVER SUPPORTING ARM  
HEX NUT M5-.8  
FLAT WASHER 72MM  
BEARING 7207  
BALL BEARING 6007ZZ  
BALL BEARING 6206ZZ  
BEARING COVER  
INT RETAINING RING 75MM  
BALL BEARING 6009Z  
THRUST BEARING 1052  
TABLE LOCKING SCREW  
HANDLE BAR  
SADDLE  
SADDLE GIB  
WAY COVER  
XM1001046  
XPR67M  
XP6009  
XM1001049  
-37-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
95  
96  
97  
98  
XM1001095  
CROSS LEAD SCREW  
CROSS FEED NUT  
CROSS FEED BEARING BRACKET  
STOP BLOCK  
STOP BLOCK FIXTURE  
CROSS ADJUSTING SCREW  
KNEE  
138  
139  
140  
141  
142  
143  
144  
146  
147  
148  
149  
150  
151  
152  
153  
154  
155  
156  
157  
158  
159  
160  
161  
162  
163  
164  
165  
166  
167  
168  
169  
170  
171  
172  
173  
174  
175  
XPK25M  
KEY 7 X 7 X 20  
FLEXIBLE CONDUIT  
WIRE  
WIRING TERMINAL  
CONNECTOR  
FLAT WASHER 6MM  
SHOULDER BOLT M10-1.5 X 74  
BASE CABINET  
XM1001096  
XM1001097  
XM1001098  
XM1001099  
XM1001100  
XM1001102  
XM1001103  
XM1001104  
XM1001105  
XM1001106  
XM1001108  
XM1001109  
XM1001110  
XM1001111  
XM1001112  
XM1001113  
XM1001114  
XM1001115  
XM1001117  
XM1001118  
XPSB06M  
XP6004  
XPK99M  
XPW22M  
XPSB28M  
XP6004  
XPR09M  
XM1001127  
XPK34M  
XPSB50M  
XM1001139  
XM1001140  
XM1001141  
XM1001142  
XPW03M  
XM1001144  
XM1001146  
XM1001147  
XPB31M  
99  
100  
102  
103  
104  
105  
106  
108  
109  
110  
111  
112  
113  
114  
115  
117  
118  
119  
120  
121  
122  
123  
125  
126  
127  
128  
129  
130  
131  
132  
133  
134  
135  
136  
KNEE GIB  
KNEE LOCKING SCREW  
GEAR SHAFT SLEEVE  
GEAR SHAFT  
ELEVATING HANDLE CLUTCH  
HANDLE ARM  
ELEVATING GEAR  
ELEVATING LEAD SCREW  
ELEVATING LEAD SCREW NUT  
CHIP GUARD  
BASE  
SWITCH  
LIGHT  
RUBBER SHEET  
CAP SCREW M6-1 X 25  
BALL BEARING 6004ZZ  
KEY 6 X 6 X 15  
FLAT WASHER 45MM  
CAP SCREW M6-1 X 15  
BALL BEARING 6004ZZ  
EXT RETAINING RING 20MM  
OIL CUP  
DOOR LATCH  
HEX BOLT M10-1.5 X 40  
FLAT WASHER 10MM  
BARBED HOSE FITTING  
PHLP HD SCR M5-.8 x 8  
HINGE  
XPW04M  
XM1001150  
XPS05M  
XM1001152  
XM1001153  
XM1001154  
XM1001155  
XM1001156  
XM1001157  
XM1001158  
XPAW03M  
XPAW04M  
XPAW05M  
XPAW06M  
XPWR1719  
XPWR1214  
XM1001165  
XM1001166  
XM1001167  
XPSB48M  
SAFETY SWITCH  
240V ON OFF SWITCH  
T-BOLTS M12-1.75 X 40  
SHELL MILL 3"  
POWER FEED UNIT  
SINGLE SHOT OILER  
HEX WRENCH 3MM  
HEX WRENCH 4MM  
HEX WRENCH 5MM  
HEX WRENCH 6MM  
OPEN END WRENCH 17/19MM  
OPEN END WRENCH 12/14MM  
SCREWDRIVER  
PHILLIPS HEAD SCREWDRIVER  
TOOLBOX  
CAP SCREW M6-1 X 35  
PULLEY BASE  
SHOULDER BOLT M8-1.25 X 60  
PHLP HD SCR M4-.7 x 6  
HEX NUT M10-1.5  
CONTACTOR DZ47  
CONTACTOR DZ47LE C32  
TRANSFORMER  
KEY 5 X 5 X 20  
CAP SCREW M5-.8 X 10  
CAP SCREW M6-1 X 45  
CAP SCREW M6-1 X 15  
EXT RETAINING RING 20MM  
CAP SCREW M6-1 X 20  
COVER  
XM1001169  
XM1001170  
XPS17M  
XPSB30M  
XPSB28M  
XPR09M  
XPSB02M  
XM1001134  
XPS03M  
XPSB31M  
XPN02M  
XM1001173  
XM1001174  
XM1001175  
PHLP HD SCR M6-1 X 8  
CAP SCREW M8-1.25 X 25  
-38-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Machine Labels  
202  
203  
204  
201  
205  
206  
207  
203  
208  
REF PART #  
201 XLABEL-09  
202 D3375  
DESCRIPTION  
REF PART #  
DESCRIPTION  
ENTANGLEMENT LABEL  
SHOPFOX LOGO SMALL  
ELECTRICITY LABEL  
205 XLABEL-07  
206 XLABEL-08  
207 XLABEL-11  
DISCONNECT LABEL  
READ MANUAL LABEL  
SAFETY GLASSES LABEL  
203 XLABEL-14  
204 XM1001204 MACHINE ID LABEL  
208 XM1001208 MODEL NUMBER LABEL  
Safety labels warn about machine hazards and how to prevent machine damage or injury. The  
owner of this machine MUST maintain the original location and readability of all labels on this  
machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the  
machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www.  
shopfoxtools.com to order new labels.  
-39-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY  
WARRANTY  
Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship  
and materials for a period of two years from the date of original purchase by the original owner.  
This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or  
accidents, lack of maintenance, or reimbursement of third party expenses incurred.  
Woodstock International, Inc. will repair or replace, at its expense and at its option, the Shop Fox  
machine or machine part, which in normal use has proven to be defective, provided that the original  
owner returns the product prepaid to a Shop Fox factory service center with proof of their purchase  
of the product within two years, and provides Woodstock International, Inc. reasonable opportunity to  
verify the alleged defect through inspection. If it is determined there is no defect, or that the defect  
resulted from causes not within the scope of Woodstock International Inc.'s warranty, then the original  
owner must bear the cost of storing and returning the product.  
This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may  
be implied by law, including any merchantability or fitness, for any particular purpose, are hereby  
limited to the duration of this written warranty. We do not warrant that Shop Fox machinery complies  
with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under  
this warranty exceed the purchase price paid for the product, and any legal actions brought against  
Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall  
in no event be liable for death, injuries to persons or property or for incidental, contingent, special or  
consequential damages arising from the use of our products.  
Every effort has been made to ensure that all Shop Fox machinery meets high quality and durability  
standards. We reserve the right to change specifications at any time because of our commitment to  
continuously improve the quality of our products.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M1001 6" x 26" Vertical Mill  
Warranty Registration  
Name___________________________________________________________________________________  
Street __________________________________________________________________________________  
City _________________________State___________________________Zip________________________  
Phone #______________________Email___________________________Invoice #___________________  
Model #_________Serial #______________Dealer Name__________________Purchase Date___________  
The following information is given on a voluntary basis. It will be used for marketing purposes to help us  
develop better products and services. Of course, all information is strictly confidential.  
1. How did you learn about us?  
_____ Advertisement  
_____ Friend  
_____ Website  
____ Local Store  
____ Other:  
_____ Mail Order Catalog  
2. How long have you been a woodworker/metalworker?  
_____ 0-2 Years _____ 2-8 Years ____8-20 Years  
_____20+ Years  
3. How many of your machines or tools are Shop Fox®?  
_____ 0-2 _____ 3-5 ____6-9  
_____10+  
4. Do you think your machine represents a good value?  
_____ Yes  
____ No  
____ No  
5. Would you recommend Shop Fox® products to a friend? _____ Yes  
6. What is your age group?  
_____ 20-29  
_____ 50-59  
_____ 30-39  
_____ 60-69  
____ 40-49  
____ 70+  
7. What is your annual household income?  
_____ $20,000-$29,000  
_____ $50,000-$59,000  
_____ $30,000-$39,000  
_____ $60,000-$69,000  
____ $40,000-$49,000  
____ $70,000+  
8. Which of the following magazines do you subscribe to?  
____ Cabinet Maker  
____ Family Handyman  
____ Hand Loader  
____ Popular Mechanics  
____ Popular Science  
____ Popular Woodworking  
____ Practical Homeowner  
____ Precision Shooter  
____ Projects in Metal  
____ RC Modeler  
____ Today’s Homeowner  
____ Wood  
____ Wooden Boat  
____ Woodshop News  
____ Woodsmith  
____ Handy  
____ Home Shop Machinist  
____ Journal of Light Cont.  
____ Live Steam  
____ Model Airplane News  
____ Modeltec  
____ Woodwork  
____ Woodworker West  
____ Woodworker’s Journal  
____ Other:  
____ Rifle  
____ Shop Notes  
____ Old House Journal  
____ Shotgun News  
9. Comments:__________________________________________________________________  
_____________________________________________________________________________  
_____________________________________________________________________________  
_____________________________________________________________________________  
_____________________________________________________________________________  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FOLD ALONG DOTTED LINE  
Place  
Stamp  
Here  
WOODSTOCK INTERNATIONAL INC.  
P.O. BOx 2309  
BELLINGHAM, WA 98227-2309  
FOLD ALONG DOTTED LINE  
TAPE ALONG EDGES--PLEASE DO NOT STAPLE  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Western Telematic Switch AFS 16 1 User Manual
Xerox Computer Monitor XR6 Series User Manual
Xerox Copier 3435 User Manual
Xerox Printer 3320 DNI User Manual
Xerox Printer Phaser 6300 User Manual
Xpelair DVR GX6 User Manual
Zanussi Freezer 110 W User Manual
Zanussi Oven 237504 User Manual
Zanussi Oven ZHM 868 User Manual
Zanussi Washer ZWH7120 P User Manual