Woodstock Planer W1829 User Manual

MODELꢀW1829ꢀ  
6"ꢀJOiNtERꢀ  
OWNER'SꢀMANUAL  
(FOR MODELS MANUFACTURED SINCE 9/11)  
Phone:ꢀ(360)ꢀ734-3482ꢀ•ꢀOnlineꢀtechnicalꢀSupport:ꢀtech-support@shopfox.biz  
COPYRiGHtꢀ©ꢀSEPtEMBER,ꢀ2011ꢀBYꢀWOODStOCKꢀiNtERNAtiONAL,ꢀiNC.  
WARNiNG:ꢀNOꢀPORtiONꢀOFꢀtHiSꢀMANUALꢀMAYꢀBEꢀREPRODUCEDꢀiNꢀANYꢀSHAPEꢀORꢀFORMꢀWitHOUt  
tHEꢀWRittENꢀAPPROVALꢀOFꢀWOODStOCKꢀiNtERNAtiONAL,ꢀiNC.  
#14362KNꢀPrintedꢀinꢀChina  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
INTRODUCTION .....................................2  
ACCESSORIES...................................... 25  
Woodstock Technical Support ..................2  
About Your Machine..............................2  
Machine Specifications .........................4  
Controls & Features .............................5  
MAINTENANCE .................................... 27  
General .......................................... 27  
Cleaning ......................................... 27  
Table & Base .................................... 27  
V-Belts ........................................... 27  
Lubrication ...................................... 27  
SAFETY...............................................6  
Standard Machinery Safety Instructions ......6  
Additional Safety for Jointers..................8  
SERVICE ............................................ 28  
General .......................................... 28  
Troubleshooting................................. 28  
Checking/Adjusting Knife Height ............ 30  
Replacing Knives................................ 32  
Setting Fence Angle Stops .................... 33  
V-Belt Replacement............................ 36  
Motor Brush Replacement..................... 37  
Electrical Safety Instructions................. 38  
Wiring Diagram ................................. 39  
ELECTRICAL .........................................9  
Circuit Requirements ............................9  
Grounding Requirements...................... 10  
Extension Cords ................................ 10  
SETUP .............................................. 11  
Unpacking ....................................... 11  
Inventory ........................................ 11  
Machine Placement ............................ 12  
Cleaning Machine............................... 12  
Bench Mounting................................. 13  
Assembly......................................... 14  
Dust Collection ................................. 16  
Recommended Adjustments .................. 16  
Power Connection.............................. 17  
Test Run.......................................... 18  
PARTS .............................................. 40  
Main .............................................. 40  
Labels ............................................ 42  
WARRANTY ........................................ 45  
OPERATIONS....................................... 19  
General .......................................... 19  
Basic Controls................................... 19  
Stock Inspection & Requirements ........... 20  
Squaring Stock.................................. 21  
Surface Planing................................. 22  
Edge Jointing ................................... 23  
Bevel Cutting ................................... 24  
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
INTRODUCTION  
Woodstock Technical Support  
This machine has been specially designed to provide many years of trouble-free service. Close attention  
to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation.  
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to  
include the basic information for safety, setup, operation, maintenance, and service of this product.  
We stand behind our machines! In the event that questions arise about your machine, please contact  
Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.  
biz. Our knowledgeable staff will help you troubleshoot problems and process warranty claims.  
If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.  
If you have comments about this manual, please contact us at:  
Woodstock International, Inc.  
Attn: Technical Documentation Manager  
P.O. Box 2309  
Bellingham, WA 98227  
About Your Machine  
The W1829 6" Jointer is a benchtop machine; its compact size makes for convenient placement in any  
shop. It mounts and dismounts quickly to a workbench making it portable when necessary.  
It is primarily used to produce straight, flat faces on a workpiece, in order to properly square the  
material for further layout, construction and joining.  
-2-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
MODEL W1829  
®
SHOP FOX 6" BENCHTOP JOINTER  
Motors  
Main  
Type.................................................................................................... Universal  
Horsepower........................................................................................... 1-1/2 HP  
Voltage...................................................................................................... 110V  
Phase.............................................................................................. Single-Phase  
Amps.......................................................................................................... 12A  
Speed............................................................................................... 20,000 RPM  
Cycle....................................................................................................... 60 Hz  
Number of Speeds............................................................................................. 1  
Power Transfer ..................................................................................... Belt Drive  
Bearings............................................................................. Shielded and Lubricated  
Main Specifications  
Cutting Capacities  
Bevel Jointing................................................................................. Left & Right 45  
Maximum Width of Cut................................................................................... 6 in.  
Maximum Depth of Cut................................................................................ 1/8 in.  
Number of Cuts Per Minute............................................................................ 20,000  
Fence Information  
Fence Length........................................................................................ 22-7/8 in.  
Fence Width............................................................................................. 3/4 in.  
Fence Height........................................................................................ 4-5/16 in.  
Fence Stops....................................................................................... 45 & 90 deg.  
Cutterhead Information  
Cutterhead Type........................................................................................ 2 Knife  
Cutterhead Diameter................................................................................ 1-7/8 in.  
Cutterhead Speed................................................................................. 10,000 RPM  
Knife Information  
Number of Knives.............................................................................................. 2  
Knife Type.............................................................................................. Straight  
Knife Length.......................................................................................... 6-1/2 in.  
Knife Width.............................................................................................. 7/8 in.  
Knife Thickness........................................................................................ 3/32 in.  
Knife Adjustment.................................................................................. Jack Screw  
-3-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Table Information  
Table Length......................................................................................... 28-1/2 in.  
Table Width........................................................................................... 6-1/4 in.  
Table Thickness......................................................................................... 1/4 in.  
Floor to Table Height.............................................................................. 73-1/4 in.  
Table Adjustment Type.................................................................................. Knob  
Table Movement Type................................................................................... Swing  
Construction  
Base.......................................................................................... Pre-formed Steel  
Body Assembly.............................................................................. Pre-formed Steel  
Fence Assembly....................................................................................... Cast Iron  
Guard................................................................................................. Aluminum  
Table............................................................................. Precision-Ground Cast Iron  
Paint............................................................................................ Powder Coated  
Other Information  
Number of Dust Ports......................................................................................... 1  
Dust Port Size......................................................................................... 2-1/2 in.  
Product Dimensions  
Weight........................................................................................................... 76 lbs.  
Width (side-to-side) x Depth (front-to-back) x Height...................................... 24 x 6 x 7-3/4 in.  
Footprint (Length x Width)......................................................................... 18-7/8 x 11 in.  
Shipping Dimensions  
Type......................................................................................................... Cardboard  
Content........................................................................................................ Machine  
Weight........................................................................................................... 80 lbs.  
Length x Width x Height............................................................................. 26 x 8 x 10 in.  
Electrical  
Power Requirement.................................................................... 110V, Single-Phase, 60 Hz  
Minimum Circuit Size......................................................................................... 15 Amp  
Cord Length....................................................................................................... 8 ft.  
Cord Gauge.................................................................................................... 16 AWG  
Plug Included....................................................................................................... Yes  
Included Plug Type........................................................................................ NEMA 5-15  
Other  
Country Of Origin ............................................................................................... China  
Warranty ........................................................................................................ 2 Year  
Assembly Time ............................................................................................ 30 Minutes  
Features  
45 Degree Inward, 90 and 45 Degree Outward Stops  
Jack Screw Knife Adjustment  
2-1/2" Dust Port  
2 Safety Push Blocks  
Dust Collection Fan, Chute and Bag  
-4-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Controls & Features  
Fence  
Cutterhead Guard  
Outfeed Table  
Infeed Table  
Dust Collection  
Chute  
Depth of Cut  
Adjusting Knob  
ON/OFF Switch  
Figure 1. W1829 identification—front view.  
Fence Tilting Handle  
Fence Bracket Assembly  
Fence Tilting  
Handle  
Figure 2. W1829 identification—rear view.  
-5-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
SAFETY  
For Your Own Safety,  
Read Manual Before Operating Machine  
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This  
manual uses a series of symbols and signal words intended to convey the level of importance of the  
safety messages. The progression of symbols is described below. Remember that safety messages by  
themselves do not eliminate danger and are not a substitute for proper accident prevention mea-  
sures—this responsibility is ultimately up to the operator!  
Indicates an imminently hazardous situation which, if not avoided,  
WILL result in death or serious injury.  
Indicates a potentially hazardous situation which, if not avoided,  
COULD result in death or serious injury.  
Indicates a potentially hazardous situation which, if not avoided,  
MAY result in minor or moderate injury.  
This symbol is used to alert the user to useful information about  
proper operation of the equipment, and/or a situation that may  
cause damage to the machinery.  
NOTICE  
Standard Machinery Safety Instructions  
Standard Machinery Safety Instructions  
OWNER’S MANUAL. Read and understand this  
owner’s manual BEFORE using machine.  
Untrained users can be seriously hurt.  
HEARING PROTECTION. Always wear hearing  
protection when operating or observing  
loud machinery. Extended exposure to this  
noise without hearing protection can cause  
permanent hearing loss.  
EYE PROTECTION. Always wear ANSI-approved  
safety glasses or a face shield when operating  
or observing machinery to reduce the risk of  
eye injury or blindness from flying particles.  
Everyday eyeglasses are not approved safety  
glasses.  
MENTAL ALERTNESS. Be mentally alert when  
running machinery. Never operate under the  
influence of drugs or alcohol, when tired, or  
when distracted.  
HAZARDOUS DUST. Dust created while using  
machinery may cause cancer, birth defects,  
or long-term respiratory damage. Be aware  
of dust hazards associated with workpiece  
materials, and always wear a NIOSH-approved  
respirator to reduce your risk.  
DISCONNECTING POWER SUPPLY. Always  
disconnect machine from power supply before  
servicing, adjusting, or changing cutting tools  
(bits, blades, cutters, etc.). Make sure switch  
is in OFF position before reconnecting to avoid  
an unexpected or unintentional start.  
WEARING PROPER APPAREL. Do not wear  
clothing, apparel, or jewelry that can become  
entangled in moving parts. Always tie back  
or cover long hair. Wear non-slip footwear to  
avoid accidental slips which could cause a loss  
of workpiece control.  
DANGEROUS ENVIRONMENTS. Do not use  
machinery in wet or rainy locations, cluttered  
areas, around flammables, or in poorly-lit  
areas. Keep work area clean, dry, and well-  
lighted to minimize risk of injury.  
-6-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
APPROVED OPERATION. Untrained operators  
can be seriously hurt by machinery. Only  
allow trained or properly supervised people  
to use machine. When machine is not being  
used, disconnect power, remove switch keys,  
or lock-out machine to prevent unauthorized  
use—especially around children. Make  
workshop kid proof!  
STABLE MACHINE. Unexpected movement during  
operations greatly increases the risk of injury  
and loss of control. Verify machines are  
stable/secure and mobile bases (if used) are  
locked before starting.  
FORCING MACHINERY. Do not force machine. It  
will do the job safer and better at the rate for  
which it was designed.  
ONLY USE AS INTENDED. Only use machine for  
its intended purpose. Never modify or alter  
machine for a purpose not intended by the  
manufacturer or serious injury may result!  
AWKWARD POSITIONS. Keep proper footing and  
balance at all times when operating machine.  
Do not overreach! Avoid awkward hand  
positions that make workpiece control difficult  
or increase the risk of accidental injury.  
USE RECOMMENDED ACCESSORIES. Consult  
this owner’s manual or the manufacturer for  
recommended accessories. Using improper  
accessories will increase the risk of serious  
injury.  
UNATTENDED OPERATION. Never leave machine  
running while unattended. Turn machine off  
and ensure all moving parts completely stop  
before walking away.  
CHILDREN & BYSTANDERS. Keep children and  
bystanders a safe distance away from work  
area. Stop using machine if children or  
bystanders become a distraction.  
MAINTAIN WITH CARE. Follow all maintenance  
instructions and lubrication schedules to  
keep machine in good working condition. An  
improperly maintained machine may increase  
the risk of serious injury.  
REMOVE ADJUSTING TOOLS. Never leave  
adjustment tools, chuck keys, wrenches, etc.  
in or on machine—especially near moving  
parts. Verify removal before starting!  
CHECK DAMAGED PARTS. Regularly inspect  
machine for damaged parts, loose bolts,  
mis-adjusted or mis-aligned parts, binding,  
or any other conditions that may affect safe  
operation. Always repair or replace damaged  
parts, wires, cords, or plugs before operating  
machine.  
SECURING WORKPIECE. When required, use  
clamps or vises to secure workpiece. A secured  
workpiece protects hands and frees both of  
them to operate the machine.  
FEED DIRECTION. Unless otherwise noted, feed  
work against the rotation of blades or cutters.  
Feeding in the same direction of rotation may  
pull your hand into the cut.  
MAINTAIN POWER CORDS. When disconnecting  
cord-connected machines from power, grab  
and pull the plug—NOT the cord. Pulling the  
cord may damage the wires inside. Do not  
handle the cord/plug with wet hands. Avoid  
cord damage by keeping it away from heated  
surfaces, high traffic areas, harsh chemicals,  
and wet or damp locations.  
GUARDS & COVERS. Guards and covers can  
protect you from accidental contact with  
moving parts or flying debris. Make sure  
they are properly installed, undamaged, and  
working correctly before using machine.  
EXPERIENCING DIFFICULTIES. If at any time you  
are experiencing difficulties performing the  
intended operation, stop using the machine!  
Contact our Technical Support for help at  
(360) 734-3482.  
NEVER STAND ON MACHINE. Serious injury or  
accidental contact with cutting tool may  
occur if machine is tipped. Machine may be  
damaged.  
-7-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Additional Safety for Jointers  
READ and understand this  
entiremanualbeforeusing  
this machine. Serious per-  
sonal injury may occur  
if safety and operational  
information is not under-  
stood and followed. DO  
NOT risk your safety by  
not reading!  
USE this and other machinery with caution  
and respect. Always consider safety first,  
as it applies to your individual working  
conditions. No list of safety guidelines can  
be complete—every shop environment is  
different. Failure to follow guidelines could  
result in serious personal injury, damage  
to equipment or poor work results.  
JOINTER KICKBACK. "Kickback" is when the workpiece is thrown off the jointer table by the force of the  
cutterhead. Always use push blocks and safety glasses to reduce the likelihood of injury from “kick-  
back.” If you do not understand what kickback is, or how it occurs, DO NOT operate this machine.  
CUTTERHEAD ALIGNMENT. Keep the edge of the cutterhead knives at top dead center (TDC) even with  
the top edge of the outfeed table to avoid kickback and personal injuries.  
WORKPIECE SUPPORT. Supporting the workpiece adequately at all times while jointing is crucial for  
making safe cuts and avoiding injury. Never attempt to make a cut with an unstable workpiece.  
PUSH BLOCKS. Always use push blocks whenever surface planing. Never pass your hands directly over  
the cutterhead without a push block.  
KICKBACK zONE. The "kickback zone" is the path directly through the end of the infeed table. Never  
stand or allow others to stand in this area during operation.  
MAxIMUM CUTTING DEPTH. The maximum cutting depth for one pass is 18". Never attempt any single  
cut deeper than this!  
JOINTING WITH THE GRAIN. Jointing against the grain or jointing end grain is dangerous and could pro-  
duce chatter or excessive chip out. Always joint with the grain.  
CUTTERHEAD GUARD. All operations must be performed with the cutterhead guard in place. Always  
ensure that the cutterhead guard is in proper working condition before operating the jointer.  
PROPER CUTTING. When cutting, always keep the workpiece moving toward the outfeed table until  
the workpiece has passed completely over the cutterhead. Never back the work toward the infeed  
table.  
USING GOOD STOCK. Jointing safety begins with the choice of stock. Inspect your stock carefully before  
feeding it over the cutterhead. Never joint a board that has loose knots, nails, or staples. If you have  
any doubts about the stability or structural integrity of your stock, DO NOT joint it!  
ExPERIENCING DIFFICULTIES. If at any time you are experiencing difficulties performing the intended  
operation, stop using the machine! Contact Tech Support at (360) 734-3482.  
-8-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
ELECTRICAL  
Circuit Requirements  
This machine must be connected to the correct size and  
type of power supply circuit, or fire or electrical damage  
may occur. Read through this section to determine if an  
adequate power supply circuit is available. If a correct  
circuit is not available, a qualified electrician MUST install  
one before you can connect the machine to power.  
The machine must be properly set up  
before it is safe to operate. DO NOT  
connect this machine to the power  
source until instructed to do later in  
this manual.  
A power supply circuit includes all electrical equipment  
between the breaker box or fuse panel in the building  
and the machine. The power supply circuit used for  
this machine must be sized to safely handle the full-  
load current drawn from the machine for an extended  
period of time. (If this machine is connected to a circuit  
protected by fuses, use a time delay fuse marked D.)  
Full-Load Current Rating  
The full-load current rating is the amperage a machine  
draws at 100% of the rated output power. On machines  
with multiple motors, this is the amperage drawn by the  
largest motor or sum of all motors and electrical devices  
that might operate at one time during normal operations.  
Incorrectly wiring or grounding this  
machine can cause electrocution, fire,  
or machine damage. To reduce this risk,  
only a qualified electrician or service  
personnel should do any required  
electrical work for this machine.  
Full-Load Current Rating at 110V .................. 12 Amps  
Circuit Requirements for 110V  
This machine can be converted to operate on a 110V  
power supply (details about voltage conversion can be  
found later in this manual). The 110V power supply circuit  
must have a verified ground and meet the requirements  
that follow:  
NOTICE  
The circuit requirements listed in this  
manual apply to a dedicated circuit—  
where only one machine will be running  
at a time. If this machine will be  
connected to a shared circuit where  
multiple machines will be running at  
the same time, consult a qualified  
electrician to ensure that the circuit is  
properly sized for safe operation.  
Circuit Type ............... 110V/120V, 60 Hz, Single-Phase  
Circuit Size ............................................. 15 Amps  
Plug/Receptacle .................................... NEMA 5-15  
-9-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Grounding Requirements  
GROUNDED  
5-15 RECEPTACLE  
110V  
This machine MUST be grounded. In the event of certain  
types of malfunctions or breakdowns, grounding provides  
a path of least resistance for electric current to travel—in  
order to reduce the risk of electric shock.  
Grounding Prong  
Improper connection of the equipment-grounding wire will  
increase the risk of electric shock. The wire with green  
insulation (with/without yellow stripes) is the equipment-  
grounding wire. If repair or replacement of the power  
cord or plug is necessary, do not connect the equipment-  
grounding wire to a live (current carrying) terminal.  
5-15 PLUG  
Neutral Hot  
Figure 3. NEMA 5-15 plug & receptacle.  
Check with a qualified electrician or service personnel  
if you do not understand these grounding requirements,  
or if you are in doubt about whether the tool is  
properly grounded. If you ever notice that a cord or  
plug is damaged or worn, disconnect it from power, and  
immediately replace it with a new one.  
DO NOT modify the provided plug or use  
an adapter if the plug will not fit your  
receptacle. Instead, have a qualified  
electrician install the proper receptacle  
on a power supply circuit that meets the  
requirements for this machine.  
For 110V Connection  
A NEMA 5-15 plug has a grounding prong that must be  
attached to the equipment-grounding wire inside the  
included power cord. The plug must only be inserted into  
a matching receptacle (see Figure 3) that is properly  
installed and grounded in accordance with all local codes  
and ordinances.  
Extension Cords  
We do not recommend using an extension cord with this  
machine. Extension cords cause voltage drop, which may  
damage electrical components and shorten motor life.  
Voltage drop increases with longer extension cords and  
the gauge smaller gauge sizes (higher gauge numbers  
indicate smaller sizes).  
Any extension cord used with this machine must contain a  
ground wire, match the required plug and receptacle, and  
meet the following requirements:  
Minimum Gauge Size at 110V ......................14 AWG  
Maximum Length (Shorter is Better) ................50 ft.  
-10-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
SETUP  
Unpacking  
This machine has been carefully packaged for safe  
transportation. If you notice the machine has been  
damaged during shipping, please contact your authorized  
Shop Fox dealer immediately.  
Inventory  
Keep machine disconnected from  
power until instructed otherwise.  
The following is a description of the main components  
shipped with the Model W1829. Lay the components out  
to inventory them.  
Note: If you can't find an item on this list, check the  
mounting location on the machine or examine the  
packaging materials carefully. Occasionally we pre-install  
certain components for safer shipping.  
A
Jointer Inventory: (Figures 4–5)  
Qty  
A. Jointer Bed Assembly .....................................1  
B. Fence........................................................1  
C. Dust Collection Bag .......................................1  
D. Push Blocks .................................................2  
E. Fence Tilting Handle......................................1  
F. Fence Bracket Assembly..................................1  
G. Fence Sliding Handle......................................1  
H. Locking Plate Assembly...................................1  
I. Fence Support..............................................1  
J. Dust Chute..................................................1  
K. Dust Collection Bag Clamp...............................1  
B
Figure 4. Large components.  
K
C
Hardware and Tools (Not shown)  
—Cap Screws M8-1.25 x 20...............................6  
—Lock Washers 8mm ......................................6  
—Hex Wrench 4mm........................................1  
—Hex Wrench 6mm........................................1  
J
D
H
F
E
I
G
Figure 5. Small components.  
-11-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Machine Placement  
Cleaning Machine  
The tables and other unpainted parts of your  
jointer are coated with a waxy grease that  
protects them from corrosion during shipment.  
Clean this grease off with a solvent cleaner or  
citrus-based degreaser. DO NOT use chlorine-  
based solvents such as brake parts cleaner or  
acetone—if you happen to splash some onto a  
painted surface, you will ruin the finish.  
Workbench Load: Refer to the Machine  
Specifications, on Page 3, for the weight  
and footprint specifications of your  
machine. Some workbenches may require  
additional reinforcement to support both  
the weight of the machine and materials.  
Working Clearances: Consider the size  
of material to be processed through  
the machine, space for auxiliary stands,  
work tables and other machinery when  
establishing a location for your Jointer.  
See Figure 6 for the overall machine  
measurements.  
NEVER clean with gasoline  
or other petroleum-  
based solvents. Most have  
low flash points, which  
make them extremely  
flammable. A risk of  
explosion and burning  
exists if these products  
are used. Serious personal  
injury may occur if this  
warning is ignored!  
21"  
29"  
ALWAYS work in well-  
ventilated areas far from  
possible ignition sources  
when using solvents to  
clean machinery. Many  
solvents are toxic when  
inhaled or ingested. Use  
care when disposing  
of waste rags and  
towels to be sure they  
DO NOT create fire or  
environmental hazards.  
Figure 6. Machine dimensions.  
USE helpers or power lift-  
ing equipment to lift this  
6" Jointer. Otherwise,  
serious personal injury  
may occur.  
MAKE your shop “child  
safe.Close and lock all  
entrances  
when  
you  
are away. NEVER allow  
untrained visitors in your  
shop when assembling,  
adjusting or operating  
equipment.  
-12-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Bench Mounting  
The strongest bench mounting option is a "Through  
Mount" where holes are drilled all the way through the  
workbench, and hex bolts, washers, and hex nuts are  
used to secure the machine to the workbench.  
Bolt  
Another option for mounting is a "Direct Mount" where the  
machine is simply secured to the workbench with a lag  
screw.  
Flat Washer  
Machine Base  
Workbench  
Flat Washer  
Lock Washer  
Hex Nut  
This machine must be securely fastened to a stable  
working surface before operating. Failure to do so  
will produce unsafe operating conditions.  
Figure 7. Example of a through mount.  
Lag Screw  
Flat Washer  
Machine Base  
Workbench  
Figure 8. Example of a direct mount.  
-13-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Assembly  
Cap Screws  
To assemble the jointer, do these steps:  
1. DISCONNECT JOINTER FROM POWER!  
2. Use two of the included M8-1.25 x 20 cap screws and  
lock washers 8mm to attach the fence support to the  
jointer bed, as shown in Figure 9.  
Fence  
Support  
Figure 9. Attaching the fence support.  
3. Insert the locking plate assembly into the fence  
support, positioning it so the two pins are against  
the bottom edge of the fence support, as shown in  
Figure 10.  
Locking Plate  
Assembly  
Locking  
Plate Pins  
Figure 10. Inserting the locking plate.  
4. Secure the locking plate in position with the fence  
sliding handle, as shown in Figure 11.  
Locking Plate  
Assembly  
Fence Sliding  
Handle  
Figure 11. Installing fence sliding handle.  
5. Use the remaining four M8-1.25 x 20 cap screws and  
8mm lock washers to attach the fence to the fence  
bracket assembly, as shown in Figure 12.  
Bracket  
Assembly  
Fence  
Cap  
Screws  
Figure 12. Attaching the fence bracket  
assembly to the fence.  
-14-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
6. Slide the fence bracket assembly over and onto the  
dovetail of the support and locking plate, as shown  
in Figure 13.  
Fence  
Bracket  
Assembly  
Fence Support  
Dovetail  
Figure 13. Sliding the fence bracket onto  
the fence support dovetails.  
7. Slide the fence forward until it contacts the  
cutterhead guard and the cutterhead guard  
completely covers the cutterhead, as shown in  
Figure 14.  
Fence  
Jointer Tables  
Cutterhead  
Guard  
Figure 14. Fence positioned over the  
jointer tables.  
8. Install the fence tilting handle by screwing the  
handle shaft into the bracket assembly, as shown in  
Figure 15.  
Outward  
Stop  
Bracket  
Assembly  
Fence Tilting  
Handle Shaft  
Figure 15. Installing the fence tilting  
handle.  
-15-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Dust Collection  
The W1829 has a built-in dust collection fan and chip  
exhaust. It also includes a 2.5" dust port, clamp, and dust  
collection bag. The W1829 can also be hooked up to a  
pre-existing dust collection system.  
DO NOT operate this machine with-  
out an adequate dust collection sys-  
tem. This machine creates substantial  
amounts of wood dust while operating.  
Failure to use a dust collection system  
can result in short and long-term respi-  
ratory illness.  
Recommended CFM at Dust Port: ................ 150 CFM  
Do not confuse this CFM recommendation with the rating  
of the dust collector. To determine the CFM at the  
dust port, you must take into account many variables,  
including the CFM rating of the dust collector, the length  
of hose between the dust collector and the machine, the  
amount of branches or Y's, and the amount of other open  
lines throughout the system. Explaining this calculation  
is beyond the scope of this manual. If you are unsure of  
your system, consult an expert or purchase a good dust  
collection "how-to" book.  
To install the dust port and collection bag, do these  
steps:  
1. Install the dust port to the chip exhaust, as shown in  
Figure 16.  
2. Slip the bag clamp over the collection bag, then  
attach the collection bag to the dust port and clamp  
it in place, as shown in Figure 17.  
Figure 16. Installing the dust port.  
Recommended  
Adjustments  
For your convenience, the adjustments listed below have  
been performed at the factory and no further setup is  
required to operate your machine.  
However, because of the many variables involved with  
shipping, we recommend that you at least verify the  
following adjustments to ensure the best possible results  
from your new machine.  
Figure 17. Attaching the dust collection  
Step-by-step instructions for these adjustments can be  
found in Service on Page 28.  
bag.  
1. Knife settings (see Page 30).  
2. Fence stop accuracy (see Page 33).  
-16-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Power Connection  
After you have completed all previous setup instructions  
and circuit requirements, the machine is ready to be  
connected to the power supply.  
To avoid unexpected startups or property damage, use  
the following steps whenever connecting or disconnecting  
the machine.  
Connecting Power  
1. Turn the machine power switch OFF.  
2. Insert the power cord plug into a matching power  
supply receptacle, as shown in Figure 18. The  
machine is now connected to the power source.  
Figure 18. Connecting power  
Disconnecting Power  
1. Turn the machine power switch OFF.  
2. Grasp the molded plug and pull it completely out of  
the power supply receptacle, as shown in Figure 19.  
DO NOT pull by the cord as this may damage the  
wires inside.  
Figure 19. Disconnecting power.  
-17-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Test Run  
Once the assembly is complete, test run your machine  
to make sure it runs properly and is ready for regular  
operation.  
The test run consists of verifying the following: 1) The  
motor powers up and runs correctly, and 2) the safety  
disabling mechanism on the switch works correctly.  
Projectiles thrown from the machine  
could cause serious eye injury. Wear  
safety glasses to reduce the risk of  
injury.  
If, during the test run, you cannot easily locate the source  
of an unusual noise or vibration, stop using the machine  
immediately, then review Troubleshooting on Page 28.  
If you still cannot remedy a problem, contact our Tech  
Support at (360) 734-3482 for assistance.  
To test run the machine, do these steps:  
1. Make sure you understand the safety instructions  
at the beginning of the manual, and verify that the  
machine is set up properly.  
2. Ensure all tools and objects used during setup are  
cleared away from the machine.  
Loose hair and clothing could get  
caught in machinery and cause serious  
personal injury. Keep loose clothing  
rolled up and long hair tied up and  
away from machinery.  
3. Verify that the machine is operating correctly by  
turning it ON.  
— When operating correctly, the machine runs  
smoothly with little or no vibration or rubbing  
noises.  
— Investigate and correct strange or unusual noises  
or vibrations before operating the machine further.  
Always disconnect the machine from power when  
investigating or correcting potential problems.  
4. Turn the machine OFF.  
5. Remove the switch disabling key (see Figure 20).  
6. Try to start the machine with the paddle switch.  
— If the machine does not start, the switch disabling  
feature is working as designed.  
Figure 20. Removing switch key from  
paddle switch.  
— If the machine does start, immediately stop the  
machine. The switch disabling feature is not  
working correctly. Call Tech Support for help.  
-18-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
OPERATIONS  
General  
This machine will perform many types of operations  
that are beyond the scope of this manual. Many of these  
operations can be dangerous or deadly if performed  
incorrectly.  
The instructions in this section are written with the  
understanding that the operator has the necessary  
knowledge and skills to operate this machine. If at any  
time you are experiencing difficulties performing any  
operation, stop using the machine!  
READ and understand this entire instruc-  
tion manual before using this machine.  
Serious personal injury may occur if  
safety and operational information is not  
understood and followed. DO NOT risk  
your safety by not reading!  
If you are an inexperienced operator, we strongly  
recommend that you read books or trade articles, or seek  
training from an experienced jointer operator before  
performing any unfamiliar operations. Above all, your  
safety should come first!  
Basic Controls  
This section covers the basic parts and controls used  
during routine operations. Refer to Figures 21–22 for  
basic parts and control locations.  
A. ON/OFF Switch: Starts and stops the cutterhead  
rotation.  
The switch has a yellow safety key—removing  
it locks the switch in the OFF position. Always  
remove this yellow key when leaving the work area.  
This prevents unsupervised persons in your shop  
(especially children) from starting the jointer.  
B
A
Figure 21. W1829 basic controls in front.  
B. Depth of Cut Adjustment Knob: Changes the height  
of the infeed table to control the depth of cut.  
C. Fence Tilting Handle: Locks the fence at the desired  
angle. Use fence stops to quickly set the fence to  
90° (perpendicular to the tables), 45° inward, or 45°  
outward.  
C
D
D. Fence Sliding Handle: Allows you to adjust the  
position of the fence over the tables. ALWAYS  
tighten it before you begin operations. The position  
of the fence determines the width of the cut as  
the workpiece moves over the cutterhead. NEVER  
operate the jointer if ANY part of cutterhead is  
exposed on the work area.  
Figure 22. W1829 basic controls in back.  
-19-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Stock Inspection  
& Requirements  
Here are some rules to follow when choosing and  
jointing stock:  
FEED DIRECTION  
CORRECT  
ROTATION  
OUTFEED TABLE  
DO NOT joint or surface plane stock that contains  
loose knots. Injury to the operator or damage to the  
workpiece can occur if the knots become dislodged  
during the cutting operation.  
INFEED TABLE  
With Grain  
INCORRECT  
FEED DIRECTION  
DO NOT joint or surface plane against the grain  
direction. Cutting against the grain increases the  
likelihood of stock kickback, as well as tear-out on  
the workpiece.  
ROTATION  
OUTFEED TABLE  
INFEED TABLE  
Against Grain  
Figure 23. Correct setting for grain  
Jointing and surface planing with the grain pro-  
duces a better finish and is safer for the operator.  
Cutting with the grain is described as feeding the  
stock on the jointer so the grain points down and  
toward you as viewed on the edge of the stock (see  
Figure 23).  
alignment.  
10" Min.  
Note: If the grain changes direction along the edge  
of the board, decrease the cutting depth and make  
additional passes.  
1" Min.  
Remove foreign objects from the stock. Make sure  
that any stock you process with the jointer is clean  
and free of any dirt, nails, staples, tiny rocks or any  
other foreign objects that may damage the jointer  
blades.  
1
2" Min.  
Figure 24. Minimum dimensions for edge  
Only process natural wood fiber through your  
jointer. Never joint MDF, particle board, plywood,  
laminates or other synthetically made materials.  
jointing.  
Make sure all stock is sufficiently dried before  
jointing. Wood with a moisture content over 20%  
will cause unnecessary wear on the knives and poor  
cutting results.  
10" Min.  
DO NOT joint stock that is excessively warped or  
twisted.  
1
2" Min.  
Make sure your workpiece exceeds the minimum  
dimension requirements (see Figures 24–25)  
before edge jointing or surface planing, or it may  
break or kick back during the operation!  
1" Min.  
Figure 25. Minimum dimensions for  
surface planing.  
-20-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Squaring Stock  
Squaring stock involves four steps performed in the  
order below:  
1. Surface Plane on the Jointer: The concave face of  
the workpiece is surface planed flat with the jointer  
(see Figure 26).  
2. Surface Plane on a Thickness Planer: The opposite  
face of the workpiece is surface planed flat with a  
thickness planer (see Figure 27).  
Figure 26. Surface plane on the jointer.  
3. Edge Joint on the Jointer: The concave edge of  
the workpiece is jointed flat with the jointer (see  
Figure 28).  
This Side Previously  
Surface Planed  
4. Rip Cut on a Table Saw: The jointed edge of the  
workpiece is placed against a table saw fence and  
the opposite edge cut off (see Figure 29).  
Figure 27. Surface plane on a thickness  
planer.  
Figure 28. Edge joint on the jointer.  
This Side  
Previously Edge  
Jointed  
Figure 29. Rip cut on a table saw.  
-21-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Surface Planing  
The purpose of surface planing on the jointer is to make  
one flat face on a piece of stock (see Figures 3031) to  
prepare it for surface planing on a thickness planer.  
NOTICE  
If you are not experienced with a jointer, set  
the depth of cut to 0", and practice feeding the  
workpiece across the tables as described below.  
This procedure will better prepare you for the  
actual operation.  
Figure 30. Typical surface planing  
To surface plane on the jointer, do these steps:  
operation.  
1. Read and understand SAFETY, beginning on Page 6.  
2. Make sure your stock has been inspected for  
dangerous conditions as described in the Stock  
Inspection & Requirements instructions, on Page  
20.  
3. Set the cutting depth for your operation. (We  
suggest 132" for surface planing, using a more  
shallow depth for hard wood species or for wide  
stock.)  
Portion  
Removed With  
Jointer  
4. Make sure your fence is set to 90˚.  
5. If your workpiece is cupped (warped), place it so  
the concave side is face down on the surface of the  
infeed table.  
Figure 31. Illustration of surface planing  
results.  
6. Start the jointer.  
7. With a push block in each hand, press the workpiece  
against the table and fence with firm pressure, and  
feed the workpiece over the cutterhead (Figure 30).  
Failure to use push blocks when sur-  
face planing may result in cutterhead  
contact, which will cause serious per-  
sonal injury. Always use push blocks  
to protect your hands when surface  
planing on the jointer.  
Note: When your leading hand (with push block) gets  
within 4" of the cutterhead, lift it up and over the  
cutterhead, and place the push block on the por-  
tion of the workpiece that is on the outfeed table.  
Now, focus your pressure on the outfeed end of the  
workpiece while feeding, and repeat the same action  
with your trailing hand when it gets within 4" of the  
cutterhead. To keep your hands safe, DO NOT let  
them get closer than 4" from the cutterhead when it  
is moving!  
8. Repeat Step 7 until the entire surface is flat.  
-22-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Edge Jointing  
The purpose of edge jointing is to produce a finished,  
flat-edged surface that is suitable for joinery or finishing  
(see Figure 32). It is also a necessary step when squaring  
rough or warped stock.  
If you are not experienced with a  
jointer, set the depth of cut to 0", and  
practice feeding the workpiece across  
the tables as described below. This  
procedure will better prepare you for  
the actual operation.  
To edge joint on the jointer, do these steps:  
1. Read and understand SAFETY, on Page 6.  
2. Inspect your stock for dangerous conditions as  
described in the Stock Inspection & Requirements  
instructions, on Page 20.  
3. Set the cutting depth for your operation.  
Note: Between 116" and 18" for edge jointing, using  
a more shallow depth for certain species or for wide  
stock.  
Portion  
Removed with  
Jointer  
4. Make sure the fence is set to 90˚.  
5. If your workpiece is bowed (warped), place it so  
the concave side is face down on the surface of the  
infeed table.  
Figure 32. Illustration of edge jointing  
results.  
6. Start the jointer.  
7. Press the workpiece against the table and fence with  
firm pressure. Use your trailing hand to guide the  
workpiece through the cut, and feed the workpiece  
over the cutterhead (see Figure 33).  
Note: If your leading hand gets within 4" of the  
cutterhead, lift it up and over the cutterhead, and  
place it on the portion of the workpiece that is  
over the outfeed table. Focus your pressure on the  
outfeed end of the workpiece while feeding, and  
repeat the same action with your trailing hand if it  
gets within 4" of the cutterhead. Keep your hands  
safe—DO NOT let them get closer than 4" from the  
cutterhead!  
Figure 33. Typical edge jointing operation.  
8. Repeat Step 7 until the entire edge is flat.  
-23-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Bevel Cutting  
The purpose of bevel cutting is to cut a specific angle into  
the edge of a workpiece (see Figure 34).  
NOTICE  
If you are not experienced with a  
jointer, set the depth of cut to 0", and  
practice feeding the workpiece across  
the tables as described below. This  
procedure will better prepare you for  
the actual operation.  
The Model W1829 has preset fence stops at 45˚ inward,  
90˚, and 45˚ outward (135˚). If your situation requires  
a different angle, the preset fence stops can be easily  
adjusted for your needs.  
To bevel cut on the jointer, do these steps:  
1. Read and understand SAFETY, beginning on Page 6.  
2. Make sure your stock has been inspected for danger-  
ous conditions as described in the Stock Inspection  
& Requirements instructions, on Page 20.  
3. Set the cutting depth for your operation.  
Note: We suggest between 116" and 18" for bevel  
cutting, using a more shallow depth for hard wood  
species or for wide stock.  
Portion  
Removed With  
Jointer  
4. Make sure your fence is set to the angle of your  
desired cut.  
Figure 34. Illustration of bevel cutting  
5. If your workpiece is cupped (warped), place it so the  
results.  
concave side toward the fence.  
6. Start the jointer.  
7. With a push block in your leading hand, press  
the workpiece against the table and fence with  
firm pressure, and feed the workpiece over the  
cutterhead, as in Figure 35.  
Note: If your leading hand gets within 4" of the  
cutterhead, lift it up and over the cutterhead,  
and place the push block on the portion of the  
workpiece that is on the outfeed table. Now, focus  
your pressure on the outfeed end of the workpiece  
while feeding, and repeat the same action with  
your trailing hand when it gets within 4" of the  
cutterhead. To keep your hands safe, DO NOT let  
them get closer than 4" from the cutterhead when it  
is moving!  
Figure 35. Typical bevel cutting operation.  
8. Repeat Step 7 until the angled cut is satisfactory to  
your needs.  
-24-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
ACCESSORIES  
The following jointer accessories may be available through your local Woodstock International Inc.  
Dealer. If you do not have a dealer in your area, these products are also available through online  
dealers. Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of  
dealers at: 1-800-840-8420 or at [email protected].  
D3319—6" Replacement Jointer Knives (Set of 2)  
D1123—Steelex® Knife Sharpener  
Add a razor hone to your planer and jointer knives  
with this hand-held sharpening device. This handy tool  
sharpens flat and beveled surfaces quickly and easily.  
Great for touch-ups.  
D3640—Shop Fox Tool Table Plus  
This new tool table plus was designed to answer customer  
requests for a slightly wider and taller table. It is built to  
accommodate a variety of bench-top machines including  
the W1829 Jointer.  
W1218A—Rotacator®  
Adjust the W1829 to within ± .001". The magnetic  
base keeps the Rotacator® firmly in position while the  
indicator indexes at 0°, 90°, 180°, and 270° for unmatched  
versatility. This is an extremely precise and useful tool!  
-25-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
D2675—Safety Glasses  
D2676—Adjustable Safety Glasses  
Exceeding ANSI Z87.1–1989 standards for impact resistance,  
these Safety Glasses offer outstanding eye protection.  
Wrap around side shields provide additional protection and  
a wide field of view. Model D2676 features easily adjustable  
ear pieces.  
D2675  
D2676  
D2759—Safety Filter Mask  
This Safety Filter Mask provides greater protection over  
paper filters with its form fitting cloth seal. Level 2 filtra-  
tion provides 98.6% filtration. Ideal for the dusty shop and  
work environments. One size fits all.  
W1041—3" x 212" Adapters  
W1044—4" x 212" Adapters  
These adapters will allow you to connect the 212" dust  
chute of the W1829 to an existing dust collection system  
with standard 3" or 4" fittings.  
W1041  
W1044  
-26-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
MAINTENANCE  
General  
Regular periodic maintenance on your machine will  
ensure its optimum performance. Make a habit of  
inspecting your machine each time you use it.  
Check for the following conditions and repair or  
replace when necessary:  
Loose mounting bolts.  
Worn switch.  
Worn or damaged cords and plugs.  
Damaged V-belt.  
Any other condition that could hamper the safe  
operation of this machine.  
MAKE SURE that your machine is  
unplugged during all maintenance pro-  
cedures! If this warning is ignored, seri-  
ous personal injury may occur.  
Cleaning  
Lubrication  
Frequently blow-off sawdust and chips with compressed  
air. This is especially important for the internal working  
parts and motor. Dust build-up around the motor is a sure  
way to decrease its life span.  
Since all bearings are sealed and  
permanently lubricated, simply leave them  
alone until they need to be replaced. Do  
not lubricate them.  
Table & Base  
Tables can be kept rust-free with regular applications  
of products like SLIPIT®. For long term storage you may  
want to consider products like Boeshield T-9™.  
V-Belts  
To ensure optimum power transmission from the motor  
to the blade, the V-belt must be in good condition (free  
from cracks, fraying and wear) and properly aligned and  
tensioned (refer to V-Belt Replacement on Page 36).  
-27-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
SERVICE  
General  
This section covers the most common service adjustments or procedures that may need to be made  
during the life of your machine. If you require additional machine service not included in this section,  
please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to:  
Troubleshooting  
This section covers the most common problems and corrections with this type of  
machine. WARNING! DO NOT make any adjustments until power is disconnected and  
moving parts have come to a complete stop!  
Motor & Electrical  
PROBLEM  
POSSIBLE CAUSE  
CORRECTIVE ACTION  
Machine does not start or  
a breaker trips.  
1. Safety key removed from ON/OFF 1. Replace safety key.  
switch.  
2. Plug/receptacle is at fault or wired 2. Test for good contacts; correct the wiring.  
incorrectly.  
3. Power supply is at fault/switched 3. Ensure hot lines have correct voltage on all legs and  
OFF.  
main power supply is switched ON.  
4. Replace lockout key; replace switch.  
5. Remove/replace brushes.  
4. Lockout key is malfunctioning.  
5. Motor brushes are at fault.  
6. Motor ON/OFF switch is at fault.  
6. Replace faulty ON/OFF switch.  
7. Wiring is open/has high resistance. 7. Check for broken wires or disconnected/corroded  
connections, and repair/replace as necessary.  
8. Motor is at fault.  
8. Test/repair/replace.  
Machine stalls, is  
underpowered, or is  
overloaded.  
1. Wrong workpiece material (wood). 1. Use wood with correct moisture content, without  
glues, and little pitch/resins.  
2. Cutterhead belt slipping.  
3. Plug/receptacle is at fault.  
4. Motor brushes are at fault.  
5. Motor bearings are at fault.  
2. Replace cutterhead belt and re-tension.  
3. Test for good contacts; correct the wiring.  
4. Remove/replace brushes.  
5. Test by rotating shaft; rotational grinding/loose  
shaft requires bearing replacement.  
6. Knives dull, feed rate is too fast 6. Use sharp knives; reduce feed rate/depth of cut.  
depth of cut too great.  
7. Motor has overheated.  
8. Motor is at fault.  
7. Clean off motor, let cool, and reduce workload.  
8. Test/repair/replace.  
-28-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Motor & Electrical (continued)  
PROBLEM  
POSSIBLE CAUSE  
CORRECTIVE ACTION  
Machine has vibration or  
noisy operation.  
1. Motor or component is loose.  
1. Inspect/replace stripped or damaged bolts/nuts,  
and re-tighten with thread locking fluid.  
2. Knife blades, clamp or jack screws 2. Resharpen/replace knives as required; set knife  
are at fault.  
alignment correctly.  
3. Belts worn or loose.  
3. Inspect/replace belts with a new ones.  
4. Motor fan is rubbing on fan cover. 4. Replace dented fan cover; replace loose/damaged  
fan.  
5. Loose mounting bolts.  
6. Blade is at fault.  
5. Replace/tighten as required.  
6. Replace warped, bent, or twisted blade; resharpen  
dull blade.  
Operation  
PROBLEM  
POSSIBLE CAUSE  
CORRECTIVE ACTION  
Excessive snipe (gouge in 1. Knives set too high.  
the end of the board that  
1. Set the knives just even with the outfeed table when  
they're at TDC (top dead center).  
is uneven with the rest of  
the cut).  
2. Operator pushing down on trailing 2. Reduce/eliminate downward pressure on that end of  
end of the workpiece.  
workpiece.  
Workpiece stops in the 1. Knives set too low.  
middle of the cut.  
1. Set the knives just even with the outfeed table when  
they're at TDC (top dead center).  
Chipping.  
1. Knots or conflicting grain direction  
1. Inspect workpiece for knots and grain (Page 20);  
only use clean stock.  
in wood.  
2. Nicked or chipped blades.  
2. Adjust one of the nicked knives sideways; replace  
knives (Page 32).  
3. Feeding workpiece too fast.  
4. Taking too deep of a cut.  
3. Slow down the feed rate.  
4. Take a smaller depth of cut. (Always reduce cutting  
depth when surface planing or working with hard  
woods.)  
Fuzzy Grain.  
1. Wood may have high moisture con- 1. Check moisture content and allow to dry if moisture  
tent or surface wetness.  
2. Dull knives.  
is over 15%.  
2. Replace knives (Page 32).  
Long lines or ridges that 1. Nicked or chipped knives.  
1. Sharpen or replace knives (Page 32).  
run along the length of the  
board.  
Uneven cutter marks, wavy 1. Feeding workpiece too fast.  
1. Slow down the feed rate.  
surface, or chatter marks  
across the face of the  
board.  
2. Knives not adjusted at even heights 2. Adjust the knives so they are set up evenly in the  
in the cutterhead.  
cutterhead (Page 30).  
Board edge is concave or 1. Board not held with even pressure 1. Hold board with even pressure as it moves over the  
convex after jointing.  
on infeed and outfeed table during  
cut.  
cutterhead.  
2. Board started too uneven.  
2. Take partial cuts to remove the extreme high spots  
before doing a full pass.  
3. Board has excessive bow or twist 3. Surface plane one face so there is a good surface to  
along its length.  
position against the fence.  
4. Insufficient number of passes.  
4. It may take 3 to 5 passes to achieve a perfect edge,  
depending on the starting condition of the board and  
the depth of cut.  
-29-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Checking/Adjusting Knife  
Height  
The knives MUST be level with the outfeed table when  
they are at top dead center (their highest point during  
rotation) or the workpiece cannot be safely fed across the  
jointer.  
Tools Needed  
Qty  
Hex Wrench 4mm ...............................................1  
Hex Wrench 5mm ...............................................1  
MAKE SURE that your machine is  
unplugged during all service proce-  
dures! If this warning is ignored, seri-  
ous personal injury may occur.  
Checking Knife Height  
1. DISCONNECT JOINTER FROM POWER SOURCE!  
2. Place a straightedge on the outfeed table so it extends  
over the cutterhead. For best results, use a straight-  
edge that will stand on edge without having to be held  
in place, as illustrated in Figure 36.  
Straightedge  
Outfeed  
Infeed  
3. Rotate the cutterhead under the straightedge.  
— If the knives are parallel to the straightedge,  
rotating the cutterhead will move the straightedge  
slightly (1/8") forward; no adjustments are  
necessary.  
Figure 36. Illustration of a typical  
cutterhead alignment setup.  
Cutterhead Knife  
Clamp Screws  
— If the knives fall below the straightedge, or if the  
knives lift the straightedge and move it more than  
1
/8" when you rotate the cutterhead, the knives  
must be adjusted.  
Adjusting Knife height  
1. DISCONNECT JOINTER FROM POWER SOURCE!  
2. Block the cutterhead guard back so the cutterhead is  
fully exposed.  
Figure 37. Cutterhead knife clamp screws.  
3. Locate the knife clamp screws and knife adjustment  
jack screws (see Figures 37–38).  
Note: You will perform the procedure in Steps 4–8  
for each of the two knives.  
4. Use a 4mm hex wrench to loosen the four knife  
clamp screws.  
Knife  
Adjustment  
Jack Screws  
5. Adjust the two jack screws until both ends are  
sightly below the straightedge.  
Figure 38. Knife adjustment jack screws.  
-30-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
6. Move the straightedge to position A, as shown in  
Figure 39. Turn the jack screw nearest the fence  
counterclockwise until the end of the knife touches  
the straightedge.  
Cutterhead knives are sharp and  
laceration injuries may occur. Use  
caution when handling the cutterhead  
knives.  
7. Move the straightedge to position B, as shown in  
Figure 39. Turn the jack screw nearest the guard  
counterclockwise until the end of the knife touches  
the straightedge.  
Black Lines Represent  
Straightedge Positions  
From Overhead View  
8. Slightly tighten the clamp screws, according to the  
proper tightening sequence, as shown in Figure 40.  
Repeat Steps 6–7 for the other cutterhead knife.  
A
B
Note: Slightly tightening the clamp screws maintains  
the knife position while performing the same step  
on the other knife. They will be final tightened in a  
later step.  
8. Without disturbing the knife clamp, rotate the  
Figure 39. Straightedge positions A and B.  
cutterhead slightly to check the knife height.  
— If the knife moves the straightedge slightly (1/8")  
forward and back on the table, the knife height is  
set correctly.  
3
— If the knife does not move the straightedge slightly  
(1/8") forward and back on the table, continue to  
make fine adjustments with the jack screws until  
the knife is set correctly.  
1
2
4
10. When the knife heights are set correctly, final tighten  
each of the knives' clamp screws according to the  
proper tightening sequence (see Figure 40).  
Figure 40. Knife clamp screw tightening  
sequence.  
11. Return the cutterhead guard to the operating  
position and ensure it is working properly.  
12. Re-align the fence and tables as needed.  
13. Perform a test cut on suitable piece of scrap  
material.  
-31-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Replacing Knives  
Sharp cutterhead knives provide the best cutting results.  
Under normal operation these knives will become  
dull and need to be sharpened or replaced. Refer to  
Troubleshooting (see Page 28) to determine if the knives  
may be dull.  
Tools Needed  
Qty  
Hex Wrench 4mm ...............................................1  
Hex Wrench 5mm ...............................................1  
MAKE SURE that your machine is  
unplugged during all service proce-  
dures! If this warning is ignored, seri-  
ous personal injury may occur.  
To replace the cutterhead knives, do these steps:  
1. DISCONNECT JOINTER FROM POWER.  
2. Carefully rotate the cutterhead until the clamp  
screws are accessible.  
3. Remove the cutterhead clamp screws fastening the  
knife to the cutterhead (see Figure 41). Carefully  
remove the knife and clamp from the cutterhead.  
Cutterhead knives are sharp and  
laceration injuries may occur. Use  
caution when handling the cutterhead  
knives.  
4. Repeat Steps 2–3 for the second cutterhead knife.  
5. Clean the cutterhead thoroughly before installing  
new knives or re-installing sharpened knives.  
Clamp Screws  
6. Install one knife, clamp it in the cutterhead,  
and slightly tighten each of the clamp screws in  
sequence, as shown in Figure 42.  
Note: By tightening the clamp screws out of  
sequence, jointing results may be hampered.  
Following the tightening sequence reduces that  
possibility.  
Figure 41. Cutterhead clamp screw  
7. Repeat Step 6 for the second cutterhead knife.  
location.  
8. Check the alignment of the knives to the outfeed  
table. They should be parallel to the outfeed table.  
— If the knife is not parallel to the outfeed table,  
adjust the jack screws to fine tune the knife  
height. Refer to Checking/Adjusting Knife Height  
on Page 30.  
3
1
2
9. Follow the tightening sequence and final tighten  
each of the clamp screws for both knives, as shown  
in Figure 42.  
4
10. Ensure cutterhead guard is working properly. Align  
the fence as needed. Perform a test cut on a  
suitable piece of scrap material.  
Figure 42. Knife clamp screw tightening  
sequence.  
-32-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Setting Fence Angle Stops  
This section provides instructions for setting the fence  
angle stops precisely at 90°, 45° inward, or 45° outward.  
Note: To ensure accurate results when edge jointing,  
check the accuracy of these settings frequently (monthly  
at a minimum) and re-adjust them if necessary.  
Tools Needed  
Qty  
Flathead Screwdriver ..........................................1  
Wrench 8mm.....................................................1  
Wrench 10mm ...................................................1  
MAKE SURE that your machine is  
unplugged during all service proce-  
dures! If this warning is ignored, seri-  
ous personal injury may occur.  
Setting 90° Fence Angle Stop  
1. DISCONNECT THE JOINTER FROM POWER!  
2. Position the fence over the bed and tighten the  
sliding handle, loosen the fence tilting handle.  
Limit Block  
Limit Plate  
Rear Slot  
Tab  
3. Press the forward tab of the limit plate into the rear  
slot of the limit block.  
Jam  
Nut  
4. Tilt the fence as far as it will go towards 90º  
(perpendicular to the table) until it hits the limit  
block shaft. Tighten the fence tilting handle.  
5. Use a square to check the angle of the fence, as  
shown in Figure 44.  
Limit Block  
Inward Stop  
Shaft  
— If the fence is perpendicular to the table, the  
90º stop is set correctly; no additional steps are  
necessary. Proceed to set the 45º inward and 45º  
outward stops (see Page 34).  
Figure 43. Fence stop parts identification.  
— If the fence is not perpendicular to the table,  
adjust the 90º stop by doing Steps 6–9.  
6. Loosen the fence tilting handle, bring the fence  
to 90º with the square set against the fence, then  
tighten the handle.  
Note: Keep the limit plate tab in the rear slot of  
the limit block.  
7. Loosen the jam nut (located at the rear of the limit  
block shaft).  
Figure 44. Checking the 90º stop.  
8. Using a flathead screwdriver, turn the limit block  
shaft until it hits the fence.  
9. Tighten the jam nut. The 90º stop is now set.  
-33-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Setting 45° Inward Stop  
1. DISCONNECT JOINTER FROM POWER!  
2. With the fence positioned over the bed and the  
sliding handle locked, loosen the fence tilting handle  
and release the limit tab.  
3. Tilt the fence towards the table as far as it will go,  
then tighten the fence tilting handle.  
Note: When you tilt the fence towards the table, it  
will stop when it hits the inward stop bolt.  
4. Use a combination square to check the angle of the  
fence, as shown in Figure 45.  
Figure 45. Checking the inward 45º stop.  
— If the fence leans 45º towards the table, the  
inward 45º stop is set correctly; proceed to set the  
outward 45º stop (see Page 35).  
— If the fence does not lean 45º towards the table,  
adjust the inward 45º stop by performing Steps  
5–9.  
5. Loosen the fence tilting handle, bring the fence to  
45º, then tighten the handle just enough to keep the  
fence in position.  
6. Remove the limit block from the fence bracket  
assembly and set it aside.  
7. Using two 8mm wrenches, adjust the inward stop  
bolt (see Figure 46) until it contacts the fence  
at precisely 45º inward, then tighten the jam nut  
(where the bolt meets the bracket assembly) while  
holding the stop bolt in place. Some trial-and-error  
will be required to set this stop correctly.  
Inward  
Stop Bolt  
8. Use two 8mm wrenches to tighten the hex nut on  
the inward stop as you hold the stop in place.  
9. Put the limit block back, bring the fence back to 90º  
and tighten the tilting handle.  
Figure 46. Adjusting the inward stop bolt.  
-34-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Setting 45° Outward Stop  
1. DISCONNECT JOINTER FROM POWER!  
2. Loosen the fence tilting handle, remove the limit  
block and set it aside.  
3. Tilt the fence backward (away from the table) until  
it stops.  
Note: The fence will stop when the outward stop  
bolt hits the fence bracket.  
4. Use a square to check the angle of the fence, as  
shown in Figure 47.  
— If the fence is tilting away from the table at 45º,  
the outward stop is set correctly. Put the limit  
block back, bring the fence to 90°, and tighten  
the tilting handle.  
— If the fence is not tilting away from the table at  
45º, perform Steps 5–6 to set the outward stop  
correctly.  
Figure 47. Checking the outward 45º stop.  
5. With the outward stop bolt resting against the fence  
bracket, use an 8mm wrench to adjust the length of  
the stop until the fence is at 45º, then tighten the  
jam nut (see Figure 48).  
Outward  
Stop Bolt  
6. Put the limit block back, bring the fence to 90º and  
tighten the fence tilting handle.  
Jam Nut  
Figure 48. Outward stop bolt detail.  
-35-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
V-Belt Replacement  
The Model W1829 uses two belts to drive the cutterhead  
and the dust collection impeller. When these belts are not  
tensioned correctly, misaligned, or damaged, your jointer  
will not function properly.  
The part number for the replacement drive belt is  
X1829070; the part number for the replacement fan belt  
is X1829092.  
Refer to the parts diagram in this manual when fixing  
belt problems. If you need further assistance, call  
our Tech Support at (360) 734-3482 or send e-mail to:  
To realign or replace the cutterhead belt, do these  
steps:  
1. DISCONNECT JOINTER FROM POWER!  
2. While facing the rear of the jointer, tip it away from  
you until it rests on the fence assembly.  
3. Remove the screws that hold the motor cover to the  
jointer base. Lift the cover off and set it aside.  
4. Inspect the cutterhead belt for proper tension,  
straight alignment, and possible damage or wear.  
Note: The belt is properly tensioned if it deflects  
about 38" when you press down on middle of the  
belt with moderate pressure from your thumb or  
forefinger. The belt is properly aligned if it lies flat  
and straight on the motor shaft and drive pulley.  
Belt damage will be evident upon inspection.  
5. Loosen the four motor mounting cap screws (see  
Figure 49), but do not remove them.  
Motor Mount Screws  
6. Replace a damaged belt with a new one. Realign and  
re-tension the belt.  
7. Tighten the motor mounting screws and replace the  
motor cover.  
8. Test run the jointer, as described on Page 18. If this  
procedure does not solve the problem, call Tech  
Support.  
Cutterhead Belt  
Note: The fan belt is installed without releasing  
motor tension. Simply slide the old belt off. Slide  
the new belt on and replace the motor cover.  
Figure 49. Motor mounting screws and  
belt locations.  
-36-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Motor Brush Replacement  
This jointer has a universal motor that uses carbon  
brushes, which are considered wear-items. Refer to the  
troubleshooting guide to determine if the motor brushes  
must be replaced.  
You can order a new brush kit (two brush assemblies) by  
calling customer service and ordering part X1829024-1.  
To replace motor brushes, do these steps:  
1. DISCONNECT JOINTER FROM POWER!  
2. While facing the rear of the jointer, tip it away from  
you until it rests on the fence assembly.  
3. Remove the screws that hold the motor cover to the  
jointer base. Lift the cover off and set it aside.  
4. Vacuum all dust and debris from the motor and belt  
areas.  
5. Use a dime to unscrew the brush caps. (See Figure  
50 to locate the brush caps.)  
Brush Cap  
Locations  
Note: When you remove the brush caps, a spring  
will pop out of the socket; the carbon brush is  
firmly attached to this spring. When you buy a  
new brush kit, you will get a pair of brush/spring  
assemblies.  
Brush  
Assembly  
6. Check the brushes for wear. If a brush is worn to less  
than 332" in length, replace both brushes.  
7. Insert the brush assemblies, positioning them so they  
slide into the slots built into the sockets, then press  
the brush cap against the spring, push it into the  
socket, and turn it to lock it in the motor housing.  
Figure 50. Removing a motor brush.  
8. Replace the motor cover.  
9. Test run the jointer, as described on Page 18.  
— If the jointer runs properly, you are done.  
— If the motor does not start, either the brushes  
are not correctly aligned in the sockets or there is  
another problem with the motor or wiring. Refer  
to the Troubleshooting section for assistance.  
-37-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Electrical Safety Instructions  
These pages are current at the time of printing. However, in the spirit of improvement, we may  
make changes to the electrical systems of future machines. Study this diagram carefully. If you notice  
differences between your machine and these wiring diagrams, call Woodstock International Technical  
Support at (360) 734-3482.  
1. SHOCK HAZARD. Working on wiring that is  
connected to a power source is extremely  
dangerous. Touching electrified parts will  
result in personal injury including but not  
limited to severe burns, electrocution,  
or death. Disconnect the power from  
the machine before servicing electrical  
components!  
5. MOTOR WIRING. The motor wiring shown  
in these diagrams is current at the time  
of printing, but it may not match your  
machine. Always use the wiring diagram  
inside the motor junction box.  
6. MODIFICATIONS. Using aftermarket parts or  
modifying the wiring beyond what is shown  
in the diagram may lead to unpredictable  
results, including serious injury or fire.  
2. QUALIFIED ELECTRICIAN. Due to the  
inherent hazards of electricity, only a  
qualified electrician should perform wiring  
tasks on this machine. If you are not a  
qualified electrician, get help from one  
before attempting any kind of wiring job.  
7. CAPACITORS/INVERTERS. Some capacitors  
and power inverters store an electrical  
charge for up to five minutes after being  
disconnected from the power source. To  
avoid being shocked, wait at least this long  
before working on these components.  
3. WIRE CONNECTIONS. All connections must  
be tight to prevent wires from loosening  
during machine operation. Double-check all  
wires disconnected or connected during any  
wiring task to ensure tight connections.  
8. ELECTRICAL REQUIREMENTS. You MUST  
follow the electrical requirements at the  
beginning of this manual when connecting  
your machine to a power source.  
4. WIRE/COMPONENT DAMAGE. Damaged  
wires or components increase the risk of  
serious personal injury, fire, or machine  
damage. If you notice that any wires or  
components are damaged while performing  
a wiring task, replace those wires or  
9. EXPERIENCING DIFFICULTIES. If you are  
experiencing difficulties understanding  
the information included in this section,  
contact our Technical Support at (360) 734-  
3482.  
components before completing the task.  
WIRING DIAGRAM COLOR KEY  
BLACK  
WHITE  
GREEN  
RED  
BLUE  
YELLOW  
LIGHT  
BLUE  
The photos and diagrams  
included in this section are  
best viewed in color. You  
can view these pages in  
color at www.shopfox.biz.  
YELLOW  
GREEN  
PURPLE  
BROWN  
GRAY  
BLUE  
WHITE  
TUR-  
QUOISE  
ORANGE  
PINK  
-38-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Wiring Diagram  
Neutral  
Hot  
110 VAC  
5-15 Plug  
Ground  
(As Recommended)  
Ground  
Ground  
PADDLE SWITCH  
(viewed from behind)  
These motor wiring diagrams are  
current at the time of printing; how-  
ever, always default to the diagram on  
the inside of the junction box cover  
if it does not match this diagram, as  
it will reflect any changes since this  
manual was printed!  
Read  
Page 38  
STOP  
Before  
Wiring  
-39-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
PARTS  
Main  
68  
11  
67  
12  
10  
55  
64  
4
5
13  
68  
65  
2
9
6
63  
66  
62  
14  
2A  
8
3
66  
5
17  
18  
19  
63  
62  
65  
7
20  
73  
74  
16  
15  
75  
68  
83  
1
49  
108  
79  
21  
71  
72  
85  
23  
58  
113  
93  
97  
99  
77  
68  
22  
86  
47  
114  
46  
96  
61  
23-1  
95  
76  
57  
100  
45  
98  
78  
44-1  
57  
89  
105  
44  
56  
59  
94  
91  
112  
56  
55  
52  
87  
53  
41  
104  
55  
69  
90  
82  
81  
33  
36  
54  
35  
107  
43  
84  
60  
40  
34  
51  
31  
56  
111  
42  
30  
53  
37  
29-1  
27  
81  
29  
106  
25  
39  
24-2  
24-1  
24-3  
92  
53  
24  
24-4  
56  
55  
54  
109  
110  
102  
103  
70  
28  
58  
76  
26  
115  
76  
58  
50  
48  
79  
-40-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Parts List  
REF  
1
2
2A  
3
4
5
6
7
8
PART #  
DESCRIPTION  
TABLE  
FENCE  
FENCE ASSEMBLY  
FENCE PLATE  
FENCE TILTING HANDLE  
FLAT WASHER 8MM  
RIGHT LINK  
LEFT LINK  
PLATE SHAFT  
BRACKET SHAFT  
LIMIT PLATE  
BLOCK  
REF  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
81  
82  
83  
84  
85  
86  
87  
89  
90  
91  
92  
93  
94  
95  
96  
97  
98  
99  
100  
102  
103  
104  
105  
PART #  
DESCRIPTION  
ALIGNMENT PIN  
PUSH BLOCKS  
PADDLE SWITCH  
X1829001  
X1829002  
X1829002A  
X1829003  
X1829004  
XPW01M  
X1829049  
X1829050  
X1829051  
XP6000ZZ  
XPSS01M  
XPCAP26M  
XPLW03M  
XPW03M  
XPS09M  
XPW02M  
XPCAP17M  
X1829060  
XPS26M  
XPLW04M  
XPCAP14M  
XPCAP02M  
XPB94M  
XPN06M  
XPCAP83M  
XPN01M  
BALL BEARING 6000ZZ  
SET SCREW M6-1 X 10  
CAP SCREW M6-1 X 12  
LOCK WASHER 6MM  
FLAT WASHER 6MM  
PHLP HD SCR M5-.8 X 10  
FLAT WASHER 5MM  
CAP SCREW M4-.7 X 10  
TAP SCREW M6 X 12  
PHLP HD SCR M6-1 X 20  
LOCK WASHER 8MM  
CAP SCREW M8-1.25 X 20  
CAP SCREW M6-1 X 20  
HEX BOLT M5-.8 X 25  
HEX NUT M5-.8  
CAP SCREW M6-1 X 55  
HEX NUT M6-1  
CAP SCREW M6-1 X 30  
RIBBED V-BELT 171J5 NK  
HEX NUT M8-1.25  
HEX BOLT M8-1.25 X 35  
SHAFT RETAINER M10  
E-CLIP 6MM  
SET SCREW M6-1 X 30  
CAP SCREW M6-1 X 30  
SET SCREW M6-1 X 35  
SET SCREW M6-1 X 16  
PHLP HD SCR M5-.8 X 8  
PHLP HD SCR M4-.7 X 10  
EXT TOOTHED WASHER 4MM  
LOCK WASHER 5MM  
WIRE NUT  
EXT RETAINING RING 12MM  
BALL BEARING 6201ZZ  
STR SNAP-IN STRAIN RELIEF 5/8"  
POWER CORD 16G 3W 5-15 72"  
SPADE TERMINAL  
RING TERMINAL  
FAN RIBBED V-BELT V1.25-7A  
DUST PORT  
FLAT WASHER 5MM  
DUST COLLECTION BAG  
HEX NUT M6-1  
X1829006  
X1829007  
X1829008  
X1829009  
X1829010  
X1829011  
X1829012  
X1829013  
X1829014  
X1829015  
X1829016  
X1829017  
X1829018  
X1829019  
X1829020  
X1829021  
X1829022  
X1829023  
X1829023-1  
X1829024  
X1829024-1  
X1829024-2  
X1829024-3  
X1829024-4  
X1829025  
X1829026  
X1829027  
X1829028  
X1829029  
X1829029-1  
X1829030  
X1829031  
X1829033  
X1829034  
X1829035  
X1829036  
X1829037  
X1829039  
XPCAP115M  
X1829041  
X1829042  
X1829043  
X1829044  
XPR17M  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
23-1  
24  
24-1  
24-2  
24-3  
24-4  
25  
26  
27  
28  
29  
29-1  
30  
31  
33  
34  
35  
36  
37  
39  
40  
41  
42  
43  
44  
44-1  
45  
46  
47  
48  
SHAFT  
FENCE BRACKET  
FENCE SLIDING HANDLE  
FENCE SUPPORT  
LOCKING PLATE  
TABLE PIN  
FRAME PIN  
BRACKET  
INFEED TABLE  
TABLE FRAME  
SUPPORT PLATE  
KNOB  
XPCAP07M  
X1829070  
XPN03M  
XPB20M  
KNOB BOLT  
X1829073  
XPEC09M  
XPSS28M  
XPCAP07M  
XPSS29M  
XPSS11M  
XPS05M  
MOTOR 2HP UNIVERSAL  
CARBON BRUSH SET  
BRUSH COVER  
RING TERMINAL  
SPADE TERMINAL  
MOTOR PULLEY  
MOTOR MOUNTING PLATE  
CORD CLAMP  
XPS38M  
XPTLW01M  
XPLW01M  
X1829084  
XPR03M  
COMPRESSION SPRING  
BLADE GUARD  
RUBBER BUMPER  
TORSION SPRING  
PIN  
XP6201ZZ  
X1829087  
X1829089  
X1829090  
X1829091  
X1829092  
X1829093  
XPW02M  
X1829095  
XPN01M  
X1829097  
X1829098  
X1829099  
X1829100  
XPAW06M  
XPAW04M  
X1829104  
X1829105  
SHAFT  
CUTTERHEAD  
KNIVES 2-PC SET 6 x 7/8 x 3/32"  
KNIFE CLAMP  
DRIVE PULLEY  
JACK SCREW M4-.7 X 10  
BUTTON HD CAP SCR M6-1 X 16  
FAN PULLEY  
SPACER  
FAN SHAFT  
CLAMP 60MM  
SOLID PIN 4.5 X 20MM  
CLAMP HANDLE  
SWING BOLT M6-1 X 50  
HEX WRENCH 6MM  
HEX WRENCH 4MM  
BASE  
CHIP BLOWER MOUNTING PLATE  
EXT RETAINING RING 26MM  
IMPELLER  
X1829045  
X1829046  
X1829047  
X1829048  
CHIP EXHAUST  
CHIP COLLECTOR  
BASE BOTTOM  
SWITCH MOUNTING PLATE  
-41-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Parts List (continued)  
REF  
106  
107  
108  
109  
110  
PART #  
X1829106  
X1829107  
X1829108  
X1829109  
XPS19M  
DESCRIPTION  
REF  
111  
112  
113  
114  
115  
PART #  
DESCRIPTION  
RIGHT RUBBER FOOT  
LEFT RUBBER FOOT  
GUARD PLATE  
XPCAP68M  
X1829112  
X1829113  
X1829114  
X1829115  
CAP SCREW M6-1 X 8  
FENDER WASHER 5MM  
INFEED TABLE SUPPORT ARM  
CHIP COLLECTOR COVER PLATE  
WIRE RESTRAINT  
CUTTERHEAD COVER  
PHLP HD SCR M5-.8 X 6  
Labels  
Safety labels warn about machine hazards and how to prevent machine damage or injury. The  
owner of this machine MUST maintain the original location and readability of all labels on this  
machine. If any label is removed or becomes unreadable, REPLACE that label before allowing  
the machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or  
NOTE: Align this label with cutterhead throat.  
121  
117  
122  
119  
120  
116  
118  
REF  
116  
117  
118  
119  
PART #  
DESCRIPTION  
REF  
120  
121  
122  
PART #  
DESCRIPTION  
MACHINE ID LABEL  
CUTTERHEAD EXPOSURE LABEL  
SHOP FOX WHITE(M1006)  
XLABEL-08A  
X1829117  
XLABEL-06C  
XLABEL-04  
READ MANUAL LABEL  
CUTTERHEAD GUARD LABEL  
EYE/LUNG HAZARD LABEL  
ELECTRICITY LABEL  
X1829120  
X1829121  
XPPAINT-1  
-42-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fold along dotted lIne  
place  
stamp  
Here  
Woodstock international inc.  
p.o. box 2309  
bellingham, Wa 98227-2309  
Fold along dotted lIne  
tape along edges--please do not staple  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model W1829 (Mfg. Since 9/11)  
WARRANTY  
WARRANTY  
Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship  
and materials for a period of two years from the date of original purchase by the original owner.  
This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or  
accidents, lack of maintenance, or reimbursement of third party expenses incurred.  
Woodstock International, Inc. will repair or replace, at its expense and at its option, the Shop Fox  
machine or machine part, which in normal use has proven to be defective, provided that the original  
owner returns the product prepaid to a Shop Fox factory service center with proof of their purchase  
of the product within two years, and provides Woodstock International, Inc. reasonable opportunity to  
verify the alleged defect through inspection. If it is determined there is no defect, or that the defect  
resulted from causes not within the scope of Woodstock International Inc.'s warranty, then the original  
owner must bear the cost of storing and returning the product.  
This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may  
be implied by law, including any merchantability or fitness, for any particular purpose, are hereby  
limited to the duration of this written warranty. We do not warrant that Shop Fox machinery complies  
with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under  
this warranty exceed the purchase price paid for the product, and any legal actions brought against  
Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall  
in no event be liable for death, injuries to persons or property or for incidental, contingent, special or  
consequential damages arising from the use of our products.  
Every effort has been made to ensure that all Shop Fox machinery meets high quality and durability  
standards. We reserve the right to change specifications at any time because of our commitment to  
continuously improve the quality of our products.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
High Quality Machines and Tools  
Woodstock International, Inc. carries thousands of products designed  
to meet the needs of today's woodworkers and metalworkers.  
Ask your dealer about these fine products:  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Weed Eater Trimmer GTI 16 SUPER User Manual
Weslo Treadmill 925925 User Manual
Westinghouse Flat Panel Television WD40FX1450 User Manual
Whirlpool Microwave Oven YMT9090SF User Manual
White Rodgers Thermostat 2B61 User Manual
Wolf Appliance Company Ventilation Hood PWC542418R User Manual
Zanussi Oven FM9411 User Manual
Zanussi Range ZCG 611 User Manual
Zenoah Automobile Parts G800BPU User Manual
Zenoah Chainsaw G3300 User Manual