Weslo Treadmill 925925 User Manual

TM  
¨
Model No. WLTL25581  
Serial No.  
Write the serial number in the  
space above for future reference.  
Serial Number Decal  
QUESTIONS?  
As a manufacturer, we are  
committed to providing complete  
customer satisfaction. If you  
have questions, or if there are  
missing or damaged parts, we  
will guarantee complete satisfac-  
tion through direct assistance  
from our factory.  
TO AVOID UNNECESSARY  
DELAYS, PLEASE CALL DIRECT  
TO OUR TOLL-FREE CUSTOMER  
HOT LINE. The trained techni-  
cians on our customer hot line  
will provide immediate assis-  
tance, free of charge to you.  
CUSTOMER HOT LINE:  
1-800-999-3756  
Mon.ÐFri., 6 a.m.Ð6 p.m. MST  
CAUTION  
Read all precautions and instruc-  
tions in this manual before using  
this equipment. Save this manual  
for future reference.  
USER'S MANUAL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15. The treadmill is capable of high speeds.  
Adjust the speed in small increments to  
avoid sudden jumps in speed.  
21. When storing the treadmill, make sure that  
the storage latch is fully closed.  
22. Inspect and tighten all parts of the treadmill  
every three months.  
16. The pulse sensor is not a medical device.  
Various factors, including the user's move-  
ment, may affect the accuracy of heart rate  
readings. The pulse sensor is intended only  
as an exercise aid in determining heart rate  
trends in general.  
23. The roller guards must be 1/8 inch from the  
rear roller (see the drawing on page 4).  
Remove the key and adjust the roller guards,  
if necessary.  
24. Never drop or insert any object into any  
opening.  
17. To reduce the possibility of the treadmill  
overheating, do not operate the treadmill  
continuously for longer than one hour.  
25.  
DANGER:  
Always unplug the power  
18. Never leave the treadmill unattended while it  
is running. Always remove the key when the  
treadmill is not in use.  
cord immediately after use, before cleaning  
the treadmill, and before performing the  
maintenance and adjustment procedures  
described in this manual. Never remove the  
motor hood unless instructed to do so by an  
authorized service representative. Servicing  
other than the procedures in this manual  
should be performed by an authorized ser-  
vice representative only.  
19. Do not change the incline of the treadmill by  
placing objects under the treadmill.  
20. Do not attempt to raise, lower, or move the  
treadmill until it is properly assembled. (See  
ASSEMBLY on page 5, and HOW TO MOVE  
THE TREADMILL on page 10.) You must be  
able to safely lift 45 pounds (20 kg) in order  
to raise, lower, or move the treadmill.  
26. This treadmill is intended for in-home use  
only. Do not use this treadmill in any com-  
mercial, rental, or institutional setting.  
WARNING:  
Before beginning this or any exercise program, consult your physician.  
This is especially important for persons over the age of 35 or persons with pre-existing health prob-  
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or prop-  
erty damage sustained by or through the use of this product.  
SAVE THESE INSTRUCTIONS  
The decal shown at the right has been  
placed on your treadmill. If the decal is  
missing, or if it is not legible, please call  
our Customer Service Department, toll-  
free, to order a free replacement decal  
(see ORDERING REPLACEMENT PARTS  
on the back cover of this manual). Apply  
the decal in the location shown.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE YOU BEGIN  
Thank you for selecting the WESLO¨ CADENCE 925  
treadmill. The CADENCE 925 treadmill combines  
advanced technology with innovative design to let you  
enjoy an excellent form of cardiovascular exercise in  
the convenience and privacy of your home. And when  
youÕre not exercising, the unique CADENCE 925 can  
be folded up, requiring less than half the floor space of  
other treadmills.  
at 1-800-999-3756, Monday through Friday, 6 a.m.  
until 6 p.m. Mountain Time (excluding holidays). To  
help us assist you, please note the product model  
number and serial number before calling. The model  
number of the treadmill is WLTL25581. The serial  
number can be found on a decal attached to the tread-  
mill (see the front cover of this manual for the loca-  
tion).  
For your benefit, read this manual carefully before  
using the treadmill. If you have additional questions,  
please call our Customer Service Department toll-free  
Before reading further, please review the drawing  
below and familiarize yourself with the parts that are  
labeled.  
Water Bottle Holder  
(Bottle not included)  
Speed Control  
Accessory Tray  
Handrails  
Console  
Key/Clip  
Storage Latch  
FRONT  
Circuit Breaker  
Power Cord  
Walking Belt  
Foot Rails  
BACK  
Rear Roller  
Adjustment Bolts  
RIGHT SIDE  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
Before beginning assembly, carefully read the  
following information and instructions:  
The following tools (not included) are required  
for assembly:  
¥ Assembly requires two people.  
¥ Two (2) adjustable wrenches  
¥ One (1) phillips screwdriver  
¥ Place all parts in a cleared area and remove the  
packing materials; do not dispose of the packing  
materials until assembly is completed.  
Assembly will be more convenient if you have the  
following tools: A socket set, a set of open-end or  
closed-end wrenches, or a set of ratchet wrenches.  
¥ As you assemble the treadmill, be sure that all  
parts are oriented as shown in the drawings.  
1. With the help of a second person, carefully lay the  
treadmill on its side. Position one of the Base Legs  
(55) on one of the Uprights (37) as shown. Make  
sure that the Base Leg Pads (31) and the Front  
Wheel (34) are in the indicated positions. Attach the  
Base Leg with two Base Leg Bolts (28), two Base  
Leg Washers (29), and two Base Leg Nuts (30).  
1
28  
34  
29  
31  
37  
With the help of a second person, carefully turn the  
treadmill onto its other side. Attach the other Base  
Leg (55) as described above.  
55  
30  
With the help of a second person, carefully raise the  
treadmill to the upright position so that both Base  
Legs (55) are resting flat on the floor.  
2. Hold the treadmill firmly with both hands and lower  
the treadmill to the floor. To decrease the possibili-  
ty of injury, bend your legs and keep your back  
straight.  
2
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Carefully rotate the Console Base (45) to the posi-  
tion shown. Insert two Handrail Bolts (77) through  
the Console Base and the Upright (37). The  
Handrail Bolts must be inserted from the inside  
as shown. Attach a Handrail Nut (86) and Handrail  
Washer (85) to each Handrail Bolt.  
3
45  
85  
77  
77  
86  
86  
85  
37  
Tighten all four Handrail Bolts (77) as tightly as  
possible. Carefully lift up and push down on the  
handrails to make sure that the Console Base  
(45) does not move. Regularly inspect and tight-  
en all four Handrail Bolts.  
45  
Handrails  
77  
77  
37  
4. Attach the Frame Guide (66) to the left side of the  
Frame (21) with two Frame Guide Screws (44) as  
shown. Note: Be careful not to overtighten the  
Screws. Make sure that the thick end of the  
Frame Guide is at the bottom.  
4
66  
44  
21  
Thick end  
5. Remove the backing from the Adhesive Clip (2).  
Press the Adhesive Clip onto the base of the Upright  
(37) in the indicated location. Press the Allen  
Wrench (35) into the Adhesive Clip.  
5
37  
2
35  
6. The Console (49) requires two "AA" batteries (not  
included); alkaline batteries are recommended.  
6
49  
48  
Open the Battery Cover (48) as shown. Press two  
batteries into the battery compartment, with the nega-  
tive (Ð) ends of the batteries touching the springs.  
Close the battery cover, push up on the battery cover  
tab, and then push the tab forward as shown in the  
inset drawing. Be sure that the tab locks into place.  
Battery  
Cover Tab  
Batteries  
7. Make sure that all parts are properly tightened  
before you use the treadmill. The use of the remain-  
ing parts will be described in other sections of this  
manual. To protect the floor or carpet from dam-  
age, place a mat under the treadmill.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION AND ADJUSTMENT  
THE PERFORMANT LUBETM WALKING BELT  
risk of electric shock. This product is equipped with a  
cord having an equipment-grounding conductor and a  
grounding plug. Plug the power cord into a surge  
protector, and plug the surge protector into an  
appropriate outlet that is properly installed and  
grounded in accordance with all local codes and  
ordinances.  
Your treadmill features a walking belt coated with  
PERFORMANT LUBETM, a high-performance lubricant.  
IMPORTANT: Never apply silicone spray or other  
substances to the walking belt or the walking plat-  
form. They will deteriorate the walking belt and  
cause excessive wear.  
This product is for use on a nominal 120-volt circuit,  
and has a grounding plug that looks like the plug illus-  
trated in drawing 1 below. A temporary adapter that  
looks like the adapter illustrated in drawing 2 may be  
used to connect the surge protector to a 2-pole recep-  
tacle as shown in drawing 2 if a properly grounded  
outlet is not available.  
HOW TO PLUG IN THE POWER CORD  
DANGER:  
Improper connection  
of the equipment-grounding conductor can  
result in an increased risk of electric shock.  
Check with a qualified electrician or service-  
man if you are in doubt as to whether the  
product is properly grounded. Do not modify  
the plug provided with the productÑif it will  
not fit the outlet, have a proper outlet  
The temporary adapter should be used only until a  
properly grounded outlet (drawing 1) can be installed  
by a qualified electrician.  
The green-colored rigid ear, lug, or the like extending  
from the adapter must be connected to a permanent  
ground such as a properly grounded outlet box cover.  
Whenever the adapter is used it must be held in place  
by a metal screw. Some 2-pole receptacle outlet  
box covers are not grounded. Contact a qualified  
electrician to determine if the outlet box cover is  
grounded before using an adapter.  
installed by a qualified electrician.  
Your treadmill, like any other type of sophisticated  
electronic equipment, can be seriously damaged by  
sudden voltage changes in your homeÕs power.  
Voltage surges, spikes, and noise interference can  
result from weather conditions or from other appli-  
ances being turned on  
or off. To decrease the  
possibility of your  
1
Grounded Outlet Box  
treadmill being dam-  
aged, always use a  
surge protector (not  
included) with your  
treadmill.  
Treadmill Power Cord  
Grounding Pin  
Grounding Plug  
Grounding Plug  
Grounding Pin  
Surge protectors are  
sold at most hardware  
stores and department  
stores. Use only a UL-  
listed surge protector,  
rated at 15 amps, with  
a 14-gauge cord of five  
feet or less in length.  
Grounded Outlet  
2
Grounded Outlet Box  
Adapter  
Grounding Pin  
Grounding Plug  
This product must be  
grounded. If it should  
malfunction or break  
down, grounding pro-  
vides a path of least  
resistance for electric  
current to reduce the  
Surge Protector  
Lug  
Metal Screw  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIAGRAM OF THE CONSOLE  
Monitor Display  
Pulse Display  
Speed Control  
PulseSensor  
Key  
Clip  
Follow the steps below to operate the console.  
CAUTION: Before operating the  
console, read the following precautions.  
Insert the key fully into the power switch.  
1
Note: Inserting the key  
will not turn on the dis-  
plays. The displays will  
turn on when the  
DISPLAY button is  
pressed or when the  
walking belt is started.  
If you just installed bat-  
teries, the displays will already be on.  
¥ Do not stand on the walking belt when turn-  
ing on the power.  
¥ Always wear the clip (see the drawing  
above) while operating the treadmill. When  
the key is removed from the console, the  
walking belt will stop.  
¥ Adjust the speed in small increments.  
¥ The training zones marked below the speed  
control are general guidelines only. See  
page 14 or more information.  
Reset the console and start the walking belt.  
2
Move the speed  
control to the  
RESET position.  
Note: Each time  
the walking belt  
is stopped, the  
¥ To reduce the possibility of electric shock,  
keep the console dry. Avoid spilling liquids  
on the console and use only a sealable  
water bottle.  
speed control  
must be moved to the RESET position before  
the walking belt can be restarted.  
STEP BY STEP CONSOLE OPERATION  
Before operating the console, make sure that the  
power cord is properly plugged in. (See HOW TO  
PLUG IN THE POWER CORD on page 7.) In addition,  
make sure that batteries are installed in the console.  
(See step 6 on page 6.) If there is a thin sheet of clear  
plastic on the console, remove it.  
Next, slowly move the speed control until the  
walking belt begins to move at slow speed.  
Carefully step onto the walking belt and begin  
exercising. Change the speed of the walking belt  
as desired by moving the speed control.  
To stop the walking belt, step onto the foot rails  
and move the speed control to the RESET position.  
Step onto the foot rails of the treadmill. Next, find the  
clip attached to the key (see the drawing above). Slide  
the clip onto your waistband.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Measure your pulse, if desired.  
Follow your progress with the monitor display.  
4
3
When you are not using the pulse sensor, a ÒPÓ will  
appear in the pulse display. To measure your pulse,  
stand on the foot rails and place your thumb on the  
pulse sensor as shown. The pulse sensor is pres-  
sure activatedÑ  
The monitor display  
offers six modes  
that provide instant  
exercise feedback:  
¥ SpeedÑThis mode  
shows your speed,  
in miles per hour.  
fully press it  
Pulse  
Sensor  
down. Do not  
press too  
hard, or the  
¥ TimeÑThis mode shows the length of time you  
have exercised. Note: If you stop exercising for  
ten seconds or longer, the time mode will pause.  
circulation in  
your thumb  
will be restrict-  
ed, and your  
pulse will not be  
detected. Next,  
raise your thumb  
slightly until the  
heart-shaped  
Indicator  
¥ Distance (DIST)ÑThis mode shows the total  
number of miles you have walked or run, up to  
999. The display will then reset to zero and con-  
tinue counting.  
¥ Fat Calories (FAT CALS)ÑThis mode shows the  
approximate number of fat calories you have  
burned. (See FAT BURNING on page 14.)  
indicator in the pulse display flashes steadily. Hold  
your thumb at this level. After a few seconds, three  
dashes will appear in the display and your pulse  
will be shown. Hold your thumb on the sensor for  
another 15 seconds for the most accurate reading.  
If the displayed pulse appears to be too high or too  
low, or if your pulse is not displayed, lift your thumb  
off the sensor and allow the display to reset. Press  
down again on the sensor as described above.  
¥ Calories (CALS)ÑThis mode shows the approxi-  
mate number of calories you have burned.  
¥ ScanÑThis mode displays the other five modes,  
for five seconds each, in a repeating cycle.  
When the power is  
turned on, the Scan  
mode will be select-  
ed. One mode indica-  
tor will appear by the  
word SCAN, and  
Make sure that your thumb is positioned as shown,  
and that you are applying the proper amount of  
pressure to the pulse sensor. Try the sensor several  
times until you become familiar with it. Remember  
to stand still while measuring your pulse.  
another mode indica-  
tor will show which  
mode is currently displayed.  
Mode Indicators  
Turn off the power.  
5
To turn off the power, simply wait for about six  
minutes. If the walking belt is not moved and the  
DISPLAY button is not pressed for six minutes, the  
power will turn off automatically.  
If desired, the Speed, Time, Distance, Fat Calories  
or Calories mode can be individually selected.  
Press the MODE button repeatedly until the  
desired mode indicator appears. Make sure that  
there is not a mode indicator by the word SCAN.  
If desired, the display can be reset by pressing the  
DISPLAY button.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO FOLD AND MOVE THE TREADMILL  
HOW TO FOLD THE TREADMILL FOR STORAGE  
Before folding the treadmill, unplug the power cord.  
Caution: You must be able to safely lift 45 pounds (20  
kg) in order to raise, lower, or move the treadmill.  
1. Hold the treadmill with your hands in the locations shown  
at the right. To decrease the possibility of injury, bend  
your legs and keep your back straight. As you raise  
the treadmill, make sure to lift with your legs rather  
than your back. Raise the treadmill about halfway to the  
vertical position.  
2. Move your right hand to the position shown at the right,  
and hold the treadmill firmly. Raise the treadmill until the  
storage latch locks over the frame guide. Make sure that  
the storage latch closes fully over the frame guide.  
Storage  
Latch  
To protect the floor or carpet from damage, place a  
mat under the treadmill. Keep the treadmill out of  
direct sunlight. Do not leave the treadmill in the stor-  
age position in temperatures above 85¡ Fahrenheit.  
Closed  
Frame Guide  
HOW TO MOVE THE TREADMILL  
Before moving the treadmill, convert the treadmill to the  
storage position as described above. Make sure that the  
storage latch is locked fully over the frame guide.  
1. Hold the upper ends of the handrails. Place one foot on  
one of the front wheels as shown.  
2. Tilt the treadmill back until it rolls freely on the front  
wheels. Carefully move the treadmill to the desired loca-  
tion. Never move the treadmill without tipping it back,  
or the base pads may come off. To reduce the risk of  
injury, use extreme caution while moving the tread-  
mill. Do not attempt to move the treadmill over an  
uneven surface.  
Base Leg  
Front Wheels  
3. Place one foot on the base, and carefully lower the tread-  
mill until it is resting in the storage position.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO LOWER THE TREADMILL FOR USE  
1. Hold the upper end of the treadmill with your right hand  
as shown. Using your left hand, slide open the storage  
latch. Pivot the treadmill until the frame guide and the  
foot rail are past the storage latch.  
Storage  
Latch  
Opened  
Frame  
Guide  
2. Hold the treadmill firmly with both hands, and lower the  
treadmill to the floor. To decrease the possibility of  
injury, bend your legs and keep your back straight.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE AND TROUBLE-SHOOTING  
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and  
follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-  
free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).  
PROBLEM: The power does not turn on  
SOLUTION: a. Make sure that the power cord is plugged into a surge protector, and that the surge protector is  
plugged into a properly grounded outlet. (See HOW TO PLUG IN THE POWER CORD on page  
7.) Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or  
less in length.  
b. After the power cord has been plugged in, make sure that the key is fully inserted into the con-  
sole. See step 1 on page 8.  
c. Check the circuit breaker located on the treadmill  
c
frame near the power cord. If the switch pro-  
trudes as shown, the circuit breaker has tripped.  
To reset the circuit breaker, wait for five minutes  
and then press the switch back in.  
Reset  
Tripped  
PROBLEM: The power turns off during use  
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing  
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.  
b. Make sure that the power cord is plugged in.  
c. Remove the key from the console. Reinsert the key fully into the console. See step 1 on page 8.  
d. If the treadmill still will not run, please call our Customer Service Department, toll-free.  
PROBLEM: The displays of the console do not function properly  
SOLUTION: a. Check the batteries in the console. If the batteries need to be replaced, see assembly step 6 on  
page 6. Most problems are the result of drained batteries.  
b. Remove the six screws from the hood. Carefully  
remove the hood. Locate the Reed Switch (17) and  
the Magnet (14) on the left side of the Pulley (49).  
Turn the Pulley until the Magnet is aligned with the  
Reed Switch. Make sure that the gap between  
the Magnet and the Reed Switch is about 1/8Ó. If  
necessary, loosen the Screw (53) and move the  
Reed Switch slightly. Retighten the Screw. Re-  
attach the hood, and run the treadmill for a few min-  
utes to check for a correct speed reading.  
49  
53  
14  
17  
1/8Ó  
Top View  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PROBLEM: The walking belt is off-center or slips when walked on  
SOLUTION: a. If the walking belt has shifted to the left, first  
remove the key and UNPLUG THE POWER CORD.  
Using the allen wrench, turn the left rear roller adjust-  
ment bolt clockwise, and the right bolt counterclock-  
wise, 1/4 of a turn each. Be careful not to overtighten  
the walking belt. Plug in the power cord, insert the  
key and run the treadmill for a few minutes. Repeat  
until the walking belt is centered.  
a
b
c
b. If the walking belt has shifted to the right, first  
remove the key and UNPLUG THE POWER CORD.  
Using the allen wrench, turn the left rear roller  
adjustment bolt counterclockwise, and the right bolt  
clockwise, 1/4 of a turn each. Be careful not to over-  
tighten the walking belt. Plug in the power cord,  
insert the key and run the treadmill for a few min-  
utes. Repeat until the walking belt is centered.  
c. If the walking belt slips when walked on, first  
remove the key and UNPLUG THE POWER CORD.  
Using the allen wrench, turn both rear roller adjust-  
ment bolts clockwise, 1/4 of a turn. When the walking  
belt is correctly tightened, you should be able to lift  
each side of the walking belt 2 to 3 inches off the  
walking platform. Be careful to keep the walking belt  
centered. Plug in the power cord, insert the key and  
run the treadmill for a few minutes. Repeat until the  
walking belt is properly tightened.  
PROBLEM: The walking belt slows when walked on  
SOLUTION: a. Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less  
in length.  
b. If the walking belt is overtightened, treadmill perfor-  
b
mance may decrease and the walking belt may be  
2ÓÐ3Ó  
permanently damaged. Remove the key and  
UNPLUG THE POWER CORD. Using the allen  
wrench, turn both rear roller adjustment bolts coun-  
terclockwise, 1/4 of a turn. When the walking belt is  
properly tightened, you should be able to lift each  
side of the walking belt 2 to 3 inches off the walking  
platform. Be careful to keep the walking belt cen-  
tered. Plug in the power cord, insert the key and run  
the treadmill for a few minutes. Repeat until the  
walking belt is properly tightened.  
Rear Roller  
Adjustment Bolts  
c. If the walking belt still slows when walked on, please call our toll-free Customer Service  
Department.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONDITIONING GUIDELINES  
is activity that requires large amounts of oxygen for  
prolonged periods of time. This increases the demand  
on the heart to pump blood to the muscles, and on the  
lungs to oxygenate the blood. For aerobic exercise,  
adjust the speed of the treadmill until your heart rate is  
near the middle of your training zone. It may also be  
helpful to set the speed control on the console to AER-  
OBIC to help you maintain the proper intensity level.  
WARNING:  
Before beginning  
this or any exercise program, consult your  
physician. This is especially important for  
individuals over the age of 35 or individuals  
with pre-existing health problems.  
The pulse sensor is not a medical device.  
Various factors, including your movement,  
may affect the accuracy of heart rate readings.  
The sensor is intended only as an exercise aid  
in determining heart rate trends in general.  
High Performance Athletic Conditioning  
If your goal is high performance athletic conditioning, set  
the speed control on the console to PERFORMANCE to  
help you maintain the proper intensity level. Note: During  
the first few weeks of your exercise program, keep your  
heart rate near the low end of your training zone.  
The following guidelines will help you to plan your exer-  
cise program. RememberÑthese are general guide-  
lines only. For more detailed exercise information,  
obtain a reputable book or consult your physician.  
To measure your heart rate during exercise, use the  
pulse sensor on the console. If your heart rate is too  
high or too low, adjust the speed of the treadmill as  
needed.  
EXERCISE INTENSITY  
Whether your goal is to burn fat or to strengthen your  
cardiovascular system, the key to achieving the desired  
results is to exercise with the proper intensity. The prop-  
er intensity level can be found by using your heart rate  
as a guide. To find the proper heart rate for you, first  
find your age at the top of the chart below (ages are  
rounded off to the nearest ten years). Next, find the two  
numbers below your age. The two numbers are your  
Òtraining zone.Ó  
WORKOUT GUIDELINES  
Each workout should include the following three parts:  
Warming Up  
Start each workout with 5 to 10 minutes of stretching  
and light exercise. A proper warm-up increases your  
body temperature, heart rate, and circulation in prepa-  
ration for exercise.  
Training Zone Exercise  
After warming up, increase the intensity of your exer-  
cise until your pulse is in your training zone for 20 to 60  
minutes. (During the first few weeks of your exercise  
program, do not keep your pulse in your training zone  
for longer than 20 minutes.) Breathe regularly and  
deeply as you exerciseÑnever hold your breath.  
Fat Burning  
To burn fat effectively, you must exercise at a relatively  
low intensity level for a sustained period of time. During  
the first few minutes of exercise, your body uses easily  
accessible carbohydrate calories for energy. Only after  
the first few minutes does your body begin to use stored  
fat calories for energy. If your goal is to burn fat, adjust  
the speed of the treadmill until your heart rate is near  
the low end of your training zone. It may also be helpful  
to set the speed control on the console to FAT BURN to  
help you maintain the proper intensity level. (See page 8.)  
Cool-down  
Finish each workout with 5 to 10 minutes of stretching  
to cool down. This will increase the flexibility of your  
muscles and will help prevent post-exercise problems.  
Exercise Frequency  
To maintain or improve your condition, complete three  
workouts each week, with at least one day of rest  
between workouts. After a few months, you may com-  
plete up to five workouts each week if desired. The key  
to success is to make exercise a regular and enjoyable  
part of your everyday life.  
Aerobic Exercise  
If your goal is to strengthen your cardiovascular sys-  
tem, your exercise must be Òaerobic.Ó Aerobic exercise  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SUGGESTED STRETCHES  
The correct form for several basic stretches is shown in the  
drawings at the right. Move slowly as you stretchÑnever  
bounce.  
1
1. Toe Touch Stretch  
Stand with your knees bent slightly and slowly bend forward  
from your hips. Allow your back and shoulders to relax as you  
reach down toward your toes as far as possible. Hold for 15  
counts, then relax. Repeat 3 times. Stretches: Hamstrings,  
back of knees and back.  
2
2. Hamstring Stretch  
Sit with one leg extended. Bring the sole of the opposite foot  
toward you and rest it against the inner thigh of your extended  
leg. Reach toward your toes as far as possible. Hold for 15  
counts, then relax. Repeat 3 times for both legs. Stretches:  
Hamstrings, lower back and groin.  
3
3. Calf/Achilles Stretch  
4
With one leg in front of the other, reach forward and place  
your hands against a wall. Keep your back leg straight and  
your back foot flat on the floor. Bend your front leg, lean for-  
ward and move your hips toward the wall. Hold for 15 counts,  
then relax. Repeat 3 times for both legs. To cause further  
stretching of the achilles tendons, bend your back leg as well.  
Stretches: Calves, achilles tendons and ankles.  
4. Quadriceps Stretch  
With one hand against a wall for balance, reach back and  
grasp one foot with your other hand. Bring your heel as close  
to your buttocks as possible. Hold for 15 counts, then relax.  
Repeat 3 times for both legs. Stretches: Quadriceps and hip  
muscles.  
5
5. Inner Thigh Stretch  
Sit with the soles of your feet together and your knees out-  
ward. Pull your feet toward your groin area as far as possible.  
Hold for 15 counts, then relax. Repeat 3 times. Stretches:  
Quadriceps and hip muscles.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PART LISTÑModel No. WLTL25581  
R1299A  
Key No. Qty.  
Description  
Key No. Qty.  
Description  
1
2
3
4
5
6*  
7
8
9
1
1
1
1
1
1
1
1
1
1
12  
4
2
1
6
1
1
1
1
1
1
1
1
1
10  
1
1
4
4
4
4
2
2
2
1
2
1
1
2
12  
1
1
1
2
1
Hood  
Adhesive Clip  
Motor Belt  
Motor Pivot Nut  
Pulley/Flywheel/Fan  
Motor/Pulley/Flywheel/Fan  
Motor  
46  
47  
48  
49*  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
86  
87  
#
1
1
1
1
1
1
6
1
1
2
7
1
2
1
1
2
2
2
1
2
2
2
2
1
2
4
1
1
1
1
1
8
1
4
1
2
1
1
0
8
8
2
1
1
Upright Plug  
Console Cover  
Battery Cover  
Console Assembly  
Speed Potentiometer  
Speed Control Knob  
Ground Screw/Belt Guide Screw  
Wire Harness  
Grommet  
Base Leg  
Belly Pan Fastener  
Belly Pan  
Upright Spacer  
Motor Tension Washer  
Left Foot Rail  
Frame Pivot Nut  
Belt Guide  
Reed Switch  
Clip Screw  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
Reed Switch Clip  
Hood Anchor Screw  
Hood Anchor  
Front Roller Bolt  
Magnet  
Platform Screw  
Motor Tension Nut  
Front Roller/Pulley  
Motor Tension Bolt  
Circuit Breaker  
Power Cord Grommet  
Frame  
Power Cord  
Controller  
Motor Pivot Bolt  
Screw  
Choke  
Electronics Bracket  
Base Leg Bolt  
Base Leg Washer  
Base Leg Nut  
Base Leg Pad  
Base Leg Endcap  
Wheel Bolt  
Wire Clip  
Right Foot Rail  
Roller Guard  
Frame Guide  
Foot  
Wheel Nut  
Right Endcap  
Rear Roller Adj. Bolt  
Roller Adjustment Washer  
Rear Roller  
Ground Wire  
Walking Platform  
Walking Belt  
Releaseable Tie  
Handrail Bolt  
Cable Tie Clamp  
8Ó Cable Tie  
Motor Star Washer  
Front Roller Nut  
Latch Bracket  
Left Endcap  
Wheel  
Allen Wrench  
Frame Pivot Bolt  
Upright  
Storage Latch  
Latch Spring  
Latch Screw/Guide Screw  
Latch Spacer  
Key Clip  
Latch Decal  
Frame Guide Screw  
Console Base  
Not Used  
Handrail Washer  
Handrail Nut  
Foot Screw  
14Ó White Wire, Male/Female  
UserÕs Manual  
#
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover  
of the userÕs manual for information about ordering replacement parts.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ORDERING REPLACEMENT PARTS  
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday  
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-  
pared to give the following information when calling:  
¥ The MODEL NUMBER of the product (WLTL25581).  
¥ The NAME of the product (WESLO CADENCE¨ 925 treadmill).  
¥ The SERIAL NUMBER of the product (see the front cover of this manual).  
¥ The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED  
DRAWING at the center of this manual).  
WESLO is a registered trademark of ICON Health & Fitness, Inc.  
LIMITED WARRANTY  
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and  
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-  
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-  
ited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.  
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not  
extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse,  
improper or abnormal usage or repairs not provided by an ICON authorized service center, products used  
for commercial or rental purposes, or products used as store display models. No other warranty beyond  
that specifically set forth above is authorized by ICON.  
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-  
nection with the use or performance of the product or damages with respect to any economic loss, loss of  
property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other con-  
sequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci-  
dental or consequential damages. Accordingly, the above limitation may not apply to you.  
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of  
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth  
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above  
limitation may not apply to you.  
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.  
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813  
Part No. 146717 H01496-C R1299A  
Printed in USA © 1999 ICON Health & Fitness, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Whirlpool Air Conditioner ACS082PP0 User Manual
Whirlpool Freezer EH090F User Manual
Whirlpool Ice Maker ECKMF 6 User Manual
Whirlpool Toaster MWD 207 User Manual
White Lawn Mower Z 165 User Manual
Windsor Carpet Cleaner ADM8IA 10080010 User Manual
Xantrex Technology Portable Generator Automatic Generator User Manual
Xantrex Technology Power Supply APG HPD User Manual
Yamaha Guitar bb404f User Manual
Yamaha Music Mixer LSP User Manual