MODEL D3274
GRAVITY FEED SPRAY
GUN W/REGULATOR
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: [email protected]
COPYRIGHT © JULY, 2008 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#10833JM PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
Model D3274 Gravity Feed Spray Gun w/Regulator
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are intended
to convey the level of importance of the safety messages. The progression of
symbols is described below. Remember that safety messages by themselves do not
eliminate danger and are not a substitute for proper accident prevention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful
NOTICE
information about proper operation of the
equipment.
Safety Instructions for Pneumatic Tools
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept at a safe distance
from work area.
1. KEEP ALL SAFETY DEVICES IN
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking
to see that keys and adjusting
wrenches are removed from tool
before operation.
6. MAKE WORKSHOP CHILD PROOF by
locking your shop and shutting off
air valves.
7. DO NOT FORCE TOOL. It will do
the job better and safer at the rate
for which it was designed.
3. KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
4. DO NOT USE IN DANGEROUS
ENVIRONMENT. Do not use
8. USE THE RIGHT TOOL. Do not
force tool or attachment to do a
job for which it was not designed.
pneumatic tools in damp or wet
locations, or where any flammable
or noxious fumes may exist. Keep
work area well lighted.
9. DO NOT USE UNDER THE
INFLUENCE OF DRUGS OR
ALCOHOL.
-1-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model D3274 Gravity Feed Spray Gun w/Regulator
Safety Instructions for Pneumatic Tools
17. DISCONNECT TOOLS before
servicing, changing accessories, or
moving to another location.
10. USE PROPER AIR HOSE for the
tool. Make sure your air hose is in
good condition and is long enough
to reach your work without
stretching.
18. DO NOT OVERREACH. Keep proper
footing/balance at all times.
11. WEAR PROPER APPAREL. Do
not wear loose clothing, gloves,
neckties, rings, bracelets, or
other jewelry which may get
caught in moving parts. Non-slip
footwear is recommended. Wear a
protective hair covering to contain
long hair.
19. USE THE RECOMMENDED
ACCESSORIES. Consult owner’s
manual for recommended
accessories. The use of improper
accessories may cause risk of
injury.
20. CHECK FOR DAMAGED PARTS
BEFORE USING. Check for binding
and alignment of parts, broken
parts, part mounting, loose bolts,
and any other conditions that may
affect machine operation. Repair
or replace damaged parts.
12. ALWAYS USE SAFETY GLASSES.
Also use a face or dust mask
if cutting operation is dusty.
Everyday eyeglasses only have
impact resistant lenses, they are
NOT safety glasses.
21. NEVER LEAVE UNATTENDED TOOL
CONNECTED TO AIR. Disconnect
the air hose and do not leave tool
until it is relieved of any built up
pressure.
13. WEAR APPROVED HEARING
PROTECTION. Air escaping from
pneumatic tools can exceed safe
exposure limits and may cause
hearing damage with prolonged
exposure.
22. NEVER ALLOW UNTRAINED
USERS TO USE THIS TOOL WHILE
UNSUPERVISED.
14. SECURE WORK. Use clamps or a
vise to hold work when practical.
It is safer than using your hand
and frees both hands to operate
tool.
23. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING TOOL. Seek formal training
or research books or magazines
that specialize in pneumatic tools.
15. MAINTAIN TOOLS WITH CARE.
Keep tools lubricated and clean
for best and safest performance.
Follow instructions for lubricating
and changing accessories.
24. BE AWARE OF HOSE LOCATION
WHEN USING PNEUMATIC TOOLS.
Hoses can easily become a tripping
hazard when laid across the floor
or spread out in a disorganized
fashion.
16. REDUCE THE RISK OF
UNINTENTIONAL FIRING. Do not
carry tool with hand on trigger
and always disconnect from air
when not in use.
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model D3274 Gravity Feed Spray Gun w/Regulator
Additional Safety Instructions for Spray Guns
1. READ THIS MANUAL. This manual
contains proper operating
8. PROTECTIVE CLOTHING. Protect
exposed skin from overspray by
wearing a protective suit or other
approved garment.
instructions for this spray gun.
2. READ MATERIAL LABELS and
MATERIAL SAFETY DATA SHEETS
(MSDS). Read and know all the
instructions on the packaging label
and the MSDS before opening the
package. This information could
save your life.
9. UNSAFE USE. DO NOT point
or shoot spray gun directly at
yourself or another person or
animals. Do not attempt to use
the spray gun for any other use
than it was intended.
3. ALWAYS WEAR A NIOSH
APPROVED RESPIRATOR WHEN
SPRAYING OR WORKING AROUND
FINISHING MATERIALS.
10. STORAGE. Thoroughly clean and
dry spray gun before storage.
Store in an approved cabinet.
11. SOLVENTS. Always store solvents
and shop towels soaked in solvent
in approved containers.
4. FIRE EXTINGUISHERS. Always
have a fully charged multi class
or class B fire extinguisher in the
immediate area.
12. EYE PROTECTION. Wear eye
protection whenever spraying or
cleaning. Solvents and chemicals
can cause serious eye injury,
which could lead to blindness.
5. FLAMMABLE MATERIAL. NEVER
spray near open flame or where
any spark could occur.
13. OPERATING PRESSURE. DO NOT
exceed the recommended inlet air
pressure. Excessive pressure could
cause the spray gun to burst or
cause other internal equipment
damage.
6. FRESH AIR. Always provide
adequate exhaust to keep area
free of built up vapors, NEVER
spray in an enclosed space.
7. DISCONNECT COMPRESSED AIR.
Always disconnect the spray
14. LOCAL LAWS. Consult local
authorities regarding exhaust and
waste disposal requirements.
gun from compressed air before
cleaning, changing attachments or
when performing maintenance of
any kind on this tool.
No list of safety guidelines can be complete. Every shop environment is different.
Always consider safety first, as it applies to your individual working conditions. Use
this and other tools with caution and respect to avoid serious injury.
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model D3274 Gravity Feed Spray Gun w/Regulator
INTRODUCTION
Woodstock Technical
Support
This tool has been specially designed to
provide many years of trouble-free ser-
vice. Close attention to detail, ruggedly
built parts and a rigid quality control pro-
gram assure safe and reliable operation.
Woodstock International, Inc. is commit-
ted to customer satisfaction. Our intent
with this manual is to include the basic
information for safety, setup, operation,
maintenance, and service of this product.
We stand behind our tools! In the
event that questions arise about
Read manual before operation.
Become familiar with the spray gun
safety and operation instructions
before beginning any work. Serious
personal injury may result if safety
or operational information is not
understood or followed.
your tool, please contact Woodstock
International Technical Support at
(360) 734-3482 or send e-mail to:
[email protected]. Our knowl-
edgeable staff will help you troubleshoot
problems and process warranty claims.
If you need the latest edition of this
manual, you can download it from
If you have comments about this
manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation
Manager
P.O. Box 2309
Bellingham, WA 98227
Email: [email protected]
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model D3274 Gravity Feed Spray Gun w/Regulator
SETUP
Unpacking
This tool has been carefully packaged for safe transportation. If you notice the machine
has been damaged during shipping, please contact your authorized Shop Fox dealer
immediately.
Inventory
The following is a description of the main components shipped with the Model D3274.
Lay the components out to inventory them.
Note: If you can't find an item on this list, check the mounting location on the tool
or examine the packaging materials carefully. Occasionally we pre-install certain
components for safer shipping.
D3274 Inventory (Figure 1)
Qty
A. Material Cup ............................. 1
B. Air Regulator............................. 1
C. Spray Gun ................................ 1
D. Service Wrench.......................... 1
E. Hex Socket Tool ......................... 1
F. Filter...................................... 1
G. Cleaning Brush........................... 1
B
D
A
C
E
F
G
Figure 1. Model D3274 inventory.
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model D3274 Gravity Feed Spray Gun w/Regulator
Specifications
Controls
Operating Air Pressure ............ 30–50 PSI
Maximum Air Pressure................. 70 PSI
Material Cup Capacity................ 600 CC
Air Consumption .................4.2–7.1CFM
Maximum Fluid Pressure .............. 10 PSI
Cup Material............................Plastic
Body Material................Aluminum Alloy
Maximum Pattern Width .............250mm
Water-Based Material Compatible ......Yes
Weight ................................. 1.5 lbs.
Material Cup
Fluid Control
Atomizing
Cap
Pattern Control
Regulator Control
Trigger
Air Flow Control
Figure 3. Controls.
Assembly
1. Insert the filter into the gun body
with the knob pointing outward (see
Figure 2).
•
•
Fluid Control: Controls the volume of
material that travels through the fluid
tip by adjusting how far the trigger
can be pulled back.
Pattern Control: Adjusts the spray
pattern from a round pattern to a
wide fan.
•
•
•
Air Flow Control: Adjusts the fluid
pressure inside the spray gun.
Atomizing Cap: Adjusts the spray
pattern from vertical to horizontal.
T r ig g e r : Two stage trigger. Stage
one only releases compressed air for
blowing off the work piece. Stage two
sprays material.
Figure 2. Installing filter.
2. Screw the cup onto the top of the
body.
3. Attach the regulator to the bottom of
•
•
Material Cup: Holds the paint to be
sprayed.
the spray gun.
4. Attach the air hose to the spray gun
Regulator/Gauge: Regulates inlet air
pressure to the spray gun. It can be
attached directly to the gun for on-
the-spot air adjustments or to the air
source.
1
regulator with a ⁄4" NPT quick con-
nect fitting (not included).
5. Attach the spray gun to an air supply
regulated between 30 and 50 PSI.
Note: DO NOT attach the spray gun or
regulator control to an unregulated
air source that exceeds 120 PSI.
Note: For the best results, use a hose
that will be dedicated for spray use
only. Do not use a hose that has been
used with an in-line oiler or other
possible contaminant.
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model D3274 Gravity Feed Spray Gun w/Regulator
OPERATIONS
Spraying
The Model D3274 HVLP (high volume,
low pressure) spray gun set is designed
to spray a wide variety of materials
like lacquers, stains, primers, multi-
component paints, clear coats, acrylics,
epoxies etc. It is ideal for auto body and
woodworking projects.
EXPLOSION HAZARD! DO NOT smoke
or have any source of flame or spark
near spraying. Vapors will explode if
ignited.
To use your spray gun:
1. Read and follow the material
manufacturer's instructions for
spraying, reducing, safety, disposal,
and any other instruction on the label
or Material Safety Data Sheet (MSDS).
2. Ensure the cup is securely tightened
and all other fittings are secure to
avoid air leaks or material spills.
3. Use the regulator control (Figure 3),
to set the inlet air pressure to 30 PSI
or to the material manufacturer's
recommendations (not to exceed 70
PSI).
RESPIRATORY HAZARD! Always use
respirator rated for organic vapor
and solvent use when using spray
equipment. Failure to protect your
lungs can lead to respiratory illness
and nervous system damage.
4. Adjust the atomizing cap (Figure
3) for a vertical or horizontal spray
pattern. Refer to Atomizing Cap
and Fan Adjustments on Page 9 for
further explanation.
5. After the material has been reduced
to the manufacturer's specifications,
fill the cup with the thinned material.
6. Trial and error, along with a fair
amount of practice are necessary to
achieve the results you want. Test
your material flow and spray pattern
on a piece of cardboard or some
scrap of material similar to your
project.
TOXIC FUMES! Always use an approved
spray booth or well ventilated
area when spraying. NEVER spray
in an confined space where toxic
fumes and flammable vapors can
accumulate to deadly levels.
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model D3274 Gravity Feed Spray Gun w/Regulator
Note: Trigger position B (Figure
5) introduces air to the paint gun,
so that position C (spray), is dust,
spatter, and cloud free.
7. Adjust the fluid control knob (Figure
3), to start with a low volume of
material and keep the atomization as
low as possible. You will need to use
a combination of fluid control, inlet
air pressure, air flow control and
stroke speed to achieve the results
you want. Spray so the material wets
out nicely without running or sagging.
A–Off
B–Air
C–Spray
A
B
C
8. Use the pattern control knob (Figure
3), to adjust the spray fan to your
desired pattern.
6
7
8
7
6
Ldg`e^ZXZ
9. Keep the gun tip perpendicular to
the ground, parallel to the spraying
surface, and 6-8" from the work (as
shown in Figure 4) when spraying.
Do not allow your wrist to bend. This
will cause the gun to arc across the
surface and distribute the material
unevenly, possibly creating sags and
dry spots.
Figure 5. Spray positions.
11. Overlap each stroke by 50% while
maintaining an even speed. This will
ensure even coverage as shown in
Figure 6. Overlapping less than 50%,
as shown in the figure to the right,
may lead to missed spots or streaky
results.
+ꢀ
-ꢀ
Figure 4. Spray technique.
NOTICE
Tipping spray gun may cause material
to spill out of the cup. Always hold
the spray gun perpendicular to the
ground to avoid potential spills and
gravity feed problems.
Yes
No
Figure 6. Overlap technique.
10. Begin spraying 2-3 inches before the
work and continue to the end of the
work, as shown in Figure 5. Continue
the motion for a few inches past
the work until you are ready for the
return stroke.
12. Spray stroke should have even
consistency and parallel edges. If it
doesn't, refer to Troubleshooting on
Page 12.
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model D3274 Gravity Feed Spray Gun w/Regulator
Atomizing Cap and Fan
Adjustments
Pattern
The atomizing cap needs to be adjusted
for horizontal or vertical spraying
patterns. Spraying in the wrong direction
may lead to material build up on the
atomizing cap horn. Many performance
problems with properly thinned paint are
caused by clogged atomizing holes on
the atomizing cap horns (see Cleaning on
Page 10).
Stroke
Pattern
Control
Figure 8. Set up for horizontal spray
stroke with vertical fan pattern.
Stroke
Pattern
Horns
Pattern
Control
Figure 7. Atomizing cap horns.
Figure 9. Set up for vertical spray stroke
with horizontal fan pattern.
Rotating the pattern adjustment control
in Figure 8 and 9 will give you a range
between the two patterns in Figure 10.
Figure 10. Fan pattern adjustment.
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model D3274 Gravity Feed Spray Gun w/Regulator
CLEANING & LUBRICATION
4. Disassemble the gun by unscrewing
the fluid control knob by hand, and
removing the spring and needle
(Figure 9).
Filter
Fluid Tip
Cup
EYE INJURY! Always wear safety
glasses when disassembling the spray
gun. The material cup may still be
pressurized. Parts may also shoot out
of the gun pressure is released from
the springs.
Fluid Control
Knob
Atomizing
Cap
Needle
Spring
Figure 11. Disassembly for cleaning.
5. Unscrew the atomizing cap with your
fingers and the fluid tip with the
service wrench (Figure 1). The fully
disassembled gun should look like
Figure 9.
Cleaning
Proper cleaning is the best way to ensure
trouble-free performance from your spray
gun. If your gun is not thoroughly cleaned,
damage and poor spraying will result.
Problems caused by improper cleaning will
not be covered by the warranty. Clean the
spray gun immediately after each use.
6. Rinse these parts thoroughly in
solvent then dry with compressed air
or let air dry.
Note: If the small holes in the
atomizing cap become blocked, soak
them in clean solvent. If the blockage
still exists, clear it with a small
needle, taking great care not to
enlarge or damage the hole. Damage
to the hole will create a disrupted
spray pattern.
Basic spray gun cleaning:
1. Spray a small amount of solvent
through the spray gun.
Note: Check with local laws
regarding this practice. If you are
spraying on a regular basis, spraying
solvents into the air may be illegal. A
cabinet style spray gun cleaner may
be required.
7. Use the cleaning brush with solvent
to clean the inner orifice and other
hard to reach areas on the outside of
the spray gun body.
2. DISCONNECT THE SPRAY GUN FROM
AIR!
8. Wipe the rest of the gun body with a
shop towel and dry.
3. Put on safety glasses and unscrew the
cup.
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model D3274 Gravity Feed Spray Gun w/Regulator
Depending on the amount of use and the
type of material used, the spray gun may
need to be disassembled and cleaned
beyond what is mentioned on Page 10.
If spray patterns become affected due
to internal blockages or the gun will be
stored for an extended amount of time,
follow these additional cleaning instruc-
tions.
EXPLOSION HAZARD! Chlorinated
Solvents like Tricloroethane and
Methylene Chloride (methyl chloride)
can chemically react with aluminum
and may explode. Many parts in spray
guns are made of aluminum. Read
solvent label carefully before using
solvent.
Advanced spray gun cleaning:
1. Follow Steps 1–5 on Page 10.
NOTICE
DO NOT soak the spray gun body
in solvent. Prolonged exposure to
solvent will rapidly deteriorate the
spray gun washers and seals. Ignoring
this notice will void your warranty.
2. Insert the bigger end of the hex
socket tool into the head of the
disassembled spray gun. Use the
service wrench on the end of the hex
socket tool as a lever to remove the
fluid nozzle plug and seals, as shown
in Figure 10.
Lubrication
Lubricate the following areas with
3. Insert the smaller end of the hex
socket tool into the head of the spray
gun. Use the service wrench on the
end of the hex socket tool as a lever
to remove the screw and spring.
spray gun lube after cleaning:
A. Atomizing Cap Threads
B. Air Valve Packing
C. Trigger Pin
D. Air Flow Control Valve
E. Pattern Control
4. Follow Steps 6–8 on Page 10.
F. Fluid Control Knob
After each cleaning, apply a thin film
of petroleum jelly to the needle spring
before reassembling.
Hex
Socket
Tool
Service
Wrench
A
F
Figure 12. Removing fluid nozzle plug.
B
E
C
D
Figure 13. Lubrication points.
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model D3274 Gravity Feed Spray Gun w/Regulator
Troubleshooting
NOTICE
Before Troubleshooting, make sure your paint is properly thinned or reduced
according to the instructions given by the paint manufacturer.
Symptom
Possible Cause
1. Dry or worn fluid tip seat
permits air to seep into fluid
passage.
Possible Solution
1. Tighten fluid tip or replace
seat with new one.
Fluttering or
Spitting spray.
2. Material level too low.
2. Add material.
3. Fluid tip or strainer obstruct- 3. Clean.
ed.
4. Dry needle packing.
4. Lubricate needle.
Uneven top or bot- 1. Atomizing cap holes are
1. Clear holes.
tom pattern.
obstructed.
2. Build-up on top or bottom of
fluid tip.
2. Clean.
3. Build-up on atomizing cap is
on needle seat.
3. Clean.
Right or left arc
pattern.
1. Left or right side horn holes
are plugged.
2. Build-up on left or right side
of fluid tip.
1. Clear holes.
2. Clean.
3. Build-up of material inside
atomizing cap.
3. Clean.
Heavy deposit of
material in center.
1. The material flow exceeds
the atomizing cap capacity.
1. Lower fluid flow.
2. Inlet air pressure is too low.
3. Material is too thick.
2. Increase inlet air pressure.
3. Thin material.
Narrow center pat- 1. Volume control turned in too
1. Increase volume.
tern.
far.
2. Inlet air pressure too high.
2. Reduce inlet air pressure.
3. Increase fluid pressure.
4. Adjust material.
3. Fluid pressure is too low.
4. Material is too thin.
No spray output.
1. No pressure at gun.
2. Fluid passages dirty.
1. Check air supply.
2. Clean gun, remove any
obstructions.
3. Fluid control closed.
4. Out of paint.
3. Open.
4. Refill.
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model D3274 Gravity Feed Spray Gun w/Regulator
Symptom
Excessive over-
spray.
Possible Cause
Possible Solution
1. Reduce fluid pressure.
2. Keep gun at recommended
distance.
1. Fluid pressure too high.
2. Gun is too far from surface.
3. Spraying too fast.
3. Slow down and maintain
consistent, even parallel
stroke.
Unable to control
spray fan.
1. Pattern adjustment screw is
not seating properly.
1. Clean or replace.
2. Atomizing cap is loose.
2. Tighten atomizing cap.
1. Spraying too slowly.
2. Gun is too close to surface.
1. Adjust spraying speed.
2. Adjust spraying distance to
6–8" from surface.
Runs and sags.
3. Damaged seal.
3. Replace damaged seals.
Material leaks from 1. Cap not secure.
cup. 2. Cup not tight on gun body.
3. Leaking from cap vent hole.
1. Tighten.
2. Tighten.
3. Hold gun upright do not
tilt.
Material leaks from 1. Fluid tip loose.
1. Tighten.
gun.
2. Dry or damaged seals.
3. Excessive pressure.
2. Replace seals.
3. Reduce pressure.
Thick dimpled fin-
ish aka "Orange
Peel."
1. Holding gun too close to sur-
face.
2. Inlet air pressure too low.
3. Material not properly mixed.
1. Spray at recommended dis-
tance.
2. Check inlet air pressure.
3. Follow manufacturer's
instructions.
4. Surface is dirty or oily.
4. More surface prep is
required.
Dry Spray.
1. Inlet air pressure too high.
2. Gun too far from surface.
1. Lower inlet air pressure.
2. Keep gun at recommended
distance.
3. Gun stroke too fast.
3. Slow down and maintain
consistent even parallel
stroke.
Gun leaks from
fluid tip.
1. Debris will not let the needle 1. Clean or replace both.
seat with the fluid tip.
Contaminated
paint.
1. Water or oil in the air line.
1. Install an in-line air filter.
2. Replace air line.
3. Spray gun filter is missing.
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model D3274 Gravity Feed Spray Gun w/Regulator
D3274 PARTS BREAKDOWN
28
29
23 24 25 26 27
30
30A
31
16A
32
33
14
13 15
16
35 36 37 38
19 20 21 22
17 18
34
39
45
43
41
44
42
40
11
10
9
7
12
8
6
4
3
1A
5
2
40A
8A
46
1
52
*51
47
48
49
50
* Not Included; for aftermarket purchase only
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model D3274 Gravity Feed Spray Gun w/Regulator
D3274 PARTS LIST
REF PART #
1A XD3274001A AIR INLET VALVE ASSEMBLY
DESCRIPTION
REF PART #
DESCRIPTION
E-CLIP 4MM
27
28
29
XPEC02M
1
2
3
4
5
6
7
XD3274001A AIR ADJ. SCREW
XD3274001A AIR ADJ. KNOB
XD3274001A O-RING 2.5 X 2.1
XD3274001A DOMED SEAL WASHER
XD3274001A AIR ADJ. SPRING
XD3274001A AIR INLET VALVE
XD3274008A SWITCH SPRING
XD3274030A BREATHER PLUG
XD3274030A CONTAINER COVER
30A XD3274030A CONTAINER ASSEMBLY
30
31
32
33
34
35
36
37
38
39
XD3274030A CONTAINER
XD3277022 FILTER
XD3274032 FLUID INLET JOINT SEAL
XD3277023 FLUID INLET JOINT
XD3274034 HANGER
XD3274035 FLUID ADJ. NEEDLE
XD3277033 COMPRESSION SPRING 6 X 37
XD3277032 JOINT CAP
8A XD3274008A AIR VALVE BODY ASSEMBLY
8
9
XD3274008A AIR VALVE BODY
XD3274008A SWITCH KNOB
10
11
12
13
14
15
XD3274008A O-RING 2.4 X 1.8
XD3274008A DOMED SEAL WASHER
XD3274008A DIRECTION SCREW
XD3274016A LOCKED SPRING
XD3274016A NOZZLE NUT
XD3274038 FLUID ADJ. KNOB
XPFH31M
FLAT HD SCR M4-.7 X 8
40A XD3274040A PATTERN ADJ. KNOB ASSEMBLY
40
41
42
43
44
45
46
47
48
49
50
XD3274040A PATTERN ADJ. KNOB
XD3274040A PATTERN ADJ. KNOB
XD3274040A COPPER WASHER 8MM
XD3274040A PATTERN ADJ. SCREW
XPOR0062 O-RING 6 X 2
XD3274016A SEAL WASHER 30MM
16A XD3274016A ATOMIZER ASSEMBLY
16
17
18
19
20
21
22
23
24
25
26
XD3274016A ATOMIZER
XD3277008 FLUID NOZZLE
XD3277009 FLUID NOZZLE PLUG
XD3277010 SEAL WASHER 10MM
XD3277011 DIRECTION SCREW M11-1 X 7
XD3277012 DOMED SEAL WASHER 3.5
XD3277013 COMPRESSION SPRING 6.3 X 14
XD3274023 TRIGGER PIN I
XPEC09M
E-CLIP 6MM
XD3277041 AIR INLET 1/4" NPT
XD3277042 MULTI-TOOL WRENCH
XD3277043 HEX SOCKET TOOL
XD3277044 CLEANING BRUSH
XD3274050 AIR REGULATOR
XD3274024 TRIGGER PIN II
XD3274025 TRIGGER
*51 XD3274051 O-RING KIT
52
XD3274052 GUN BODY
XPEC02M
E-CLIP 4MM
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects
from workmanship and materials for a period of two years from the date of original
purchase by the original owner. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or
reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair or replace, at its expense and at its option,
the Shop Fox machine or machine part which in normal use has proven to be defective,
provided that the original owner returns the product prepaid to a Shop Fox factory
service center with proof of their purchase of the product within two years, and
provides Woodstock International, Inc. reasonable opportunity to verify the alleged
defect through inspection. If it is determined there is no defect, or that the defect
resulted from causes not within the scope of Woodstock International Inc.'s warranty,
then the original owner must bear the cost of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties
that may be implied by law, including any merchantability or fitness, for any particular
purpose, are hereby limited to the duration of this written warranty. We do not
warrant that Shop Fox machinery complies with the provisions of any law or acts. In
no event shall Woodstock International, Inc.'s liability under this warranty exceed the
purchase price paid for the product, and any legal actions brought against Woodstock
International, Inc. shall be tried in the State of Washington, County of Whatcom. We
shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special or consequential damages arising from the use of our products.
Every effort has been made to ensure that all Shop Fox machinery meets high quality
and durability standards. We reserve the right to change specifications at any time
because of our commitment to continuously improve the quality of our products.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty Registration
Name___________________________________________________________________________________
Street __________________________________________________________________________________
City _________________________State___________________________Zip________________________
Phone #______________________Email___________________________Invoice #___________________
Model #_________Serial #______________Dealer Name__________________Purchase Date___________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us
develop better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
Advertisement
_____ Friend
_____ Website
____ Local Store
____ Other:
Mail Order Catalog
2. How long have you been a woodworker/metalworker?
0-2 Years _____ 2-8 Years _____8-20 Years
_____20+ Years
3. How many of your machines or tools are Shop Fox?
0-2 _____ 3-5 _____6-9
_____10+
4. Do you think your machine represents a good value?
5. Would you recommend Shop Fox products to a friend?
6. What is your age group?
_____ Yes
_____ Yes
____ No
____ No
20-29
50-59
_____ 30-39
_____ 60-69
____ 40-49
____ 70+
7. What is your annual household income?
$20,000-$29,000
$50,000-$59,000
_____ $30,000-$39,000
_____ $60,000-$69,000
____ $40,000-$49,000
____ $70,000+
8. Which of the following magazines do you subscribe to?
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking
____ Practical Homeowner
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Today’s Homeowner
____ Wood
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Model Airplane News
____ Modeltec
____ Woodwork
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Rifle
____ Shop Notes
____ Old House Journal
____ Shotgun News
9. Comments:__________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
___________________________________________________________________
___________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
WOODSTOCK INTERNATIONAL INC.
P.O. BOX 2309
BELLINGHAM, WA 98227-2309
FOLD ALONG DOTTED LINE
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
|