MODEL W1758
VARIABLE SPEED WOOD LATHE
WITH DIGITAL READOUT
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED APRIL, 2010 (TS)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. (FOR MODELS MANUFACTURED SINCE 3/10)
Printed in China
#9397TS
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
INTRODUCTION ......................................2
ACCESSORIES....................................... 26
Wood Lathe Accessories....................... 26
Woodstock Technical Support ..................2
SAFETY................................................6
Standard Safety Instructions ...................6
Additional Safety for Wood Lathes............8
MAINTENANCE ..................................... 27
General .......................................... 27
Cleaning ......................................... 27
Lathe Bed........................................ 27
Tailstock ......................................... 27
Lubrication ...................................... 27
ELECTRICAL ..........................................9
110V Operation...................................9
Extension Cords ..................................9
Electrical Specifications ........................9
SERVICE............................................. 28
General .......................................... 28
Aligning Headstock & Tailstock Centers .... 28
Changing V-Belt................................. 28
Electrical Components & Wiring Diagram.. 29
Troubleshooting................................. 30
SETUP............................................... 10
Unpacking ....................................... 10
Inventory ........................................ 10
Machine Placement ............................ 11
Cleaning Machine............................... 11
Mounting to Shop Floor........................ 12
Assembly......................................... 12
Test Run.......................................... 14
PARTS ............................................... 32
Label Placement ............................... 34
OPERATIONS........................................ 15
General .......................................... 15
Adjusting Headstock........................... 16
Adjusting Tailstock............................. 17
Adjusting Tool Rest............................. 17
Installing/Removing Headstock Center ..... 18
Installing/Removing Tailstock Center ....... 19
Installing/Removing Faceplate............... 20
Selecting Turning Tools ........................ 21
Spindle Turning ................................. 22
Faceplate Turning .............................. 24
Outboard Turning............................... 25
Sanding/Finishing Using the Lathe .......... 25
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
INTRODUCTION
Woodstock Technical Support
This machine has been specially designed to provide many years of trouble-free service. Close attention
to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation.
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.
We stand behind our machines! In the event that questions arise about your machine, please contact
Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.
biz. Our knowledgeable staff will help you troubleshoot problems and process warranty claims.
If you have comments about this manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
Email: manuals@woodstockint.com
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
MACHINE
SPECIFICATIONS
MOdEl W1758
VARIABlE SPEEd WOOd lATHE WITH dIGITAl REAdOUT
Motor
Type..........................................................................................TEFC Capacitor Start Induction
Horsepower................................................................................................................. 2 HP
Voltage ......................................................................................................................110V
Phase....................................................................................................................... Single
Amps.......................................................................................................................... 14A
Speed .................................................................................................................. 1725 RPM
Cycle........................................................................................................................60 Hz
Number Of Speeds............................................................................................................. 1
Power Transfer .................................................................................................... V-Belt Drive
Bearings ............................................................................................... Sealed and Lubricated
Main Specifications
Operation Information
Swing Over Bed........................................................................................................ 16"
Maximum Distance Between Centers .............................................................................. 46"
Swing Over Tool Rest ................................................................................................. 13"
Number Of Spindle Speeds ....................................................................................Variable
Range Of Spindle Speeds................................................................................600–2400 RPM
Floor To Center Height ............................................................................................... 43"
Headstock Rotation Stops.......................................................................0, 60, 90, 120, 180°
Spindle Information
Spindle Taper ....................................................................................................... MT#2
Spindle Diameter....................................................................................................... 1"
Spindle Bore............................................................................................................3⁄8
"
Spindle Center....................................................................................................... Spur
Spindle TPI ............................................................................................................... 8
Spindle Type.................................................................................................. Right Hand
Tailstock Information
Tailstock Taper...................................................................................................... MT#2
Tailstock Center ......................................................................................................Live
Overall Dimensions
Weight .................................................................................................................. 287 lbs.
Length ......................................................................................................................721⁄2
"
Width .......................................................................................................................... 19"
Height ......................................................................................................................... 48"
Foot Print (Length/Width)........................................................................................ 54" x 133⁄4
"
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
Construction Materials
Bed................................................................................................ Precision Ground Cast Iron
Legs .....................................................................................................................Cast Iron
Headstock..............................................................................................................Cast Iron
Tool Rest ...............................................................................................................Cast Iron
Tailstock................................................................................................................Cast Iron
Paint ............................................................................................................... Powder Coat
Shipping Dimensions
Carton 1
Weight............................................................................................................. 199 lbs.
Length................................................................................................................... 63"
Width.................................................................................................................... 16"
Height................................................................................................................161⁄2
"
Carton 2
Weight............................................................................................................. 106 lbs.
Length................................................................................................................... 32"
Width.................................................................................................................151⁄2
"
Height................................................................................................................... 10"
Electrical
Switch .............................................................................................. Paddle With Lockout Key
Switch Voltage .............................................................................................................110V
Cord Length................................................................................................................. 8 ft.
Cord Gauge ....................................................................................................................16
Recommended Circuit Size................................................................................................ 20A
Plug .......................................................................................................................... 5-15
Other
Country Of Origin.........................................................................................................China
Warranty .................................................................................................................. 2 Year
Serial Number Location....................................................................................Machine ID Label
Assembly Time ...........................................................................................................1 hour
Features
Variable spindle speed from 600 to 2400 RPM
Heavy Duty, Precision Ground Cast Iron Bed
Cast Iron Legs Ensures Stability and Minimal Vibration
Quick Lock/Release Levers for Headstock and Tailstock
Outboard Turning with Standard Tool Rest Extension
Spindle Tachometer with Digital Readout
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
Controls and Features
J
C
B
I
A
K
F
G
D
H
L
E
R
P
Q
M
O
N
A. Motor
B. Digital Readout
C. Spindle
D. Spur Center
E. Speed Control Lever
F. Tool Rest
J. Quill Locking Lever
K. Quill Handwheel
L. Lathe Bed
M. Tool Rest Extension Locking Lever
N. Tool Rest Base Locking Lever
O. Tool Rest Locking Lever
G. Tool Rest Base with Extension
H. Tailstock Locking Lever
I. Live Center
P. Headstock Rotation Locking Pin
Q. ON/OFF Switch with Lockout Key
R. Headstock Locking Lever
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
SAFETY
READ MANUAL BEFORE OPERATING MACHINE.
FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL
RESULT IN PERSONAL INJURY.
Indicates an imminently hazardous situation which, if not avoided, WILL
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, MAY
result in minor or moderate injury.
This symbol is used to alert the user to useful information about proper
operation of the equipment, and/or a situation that may cause damage
to the machinery.
NOTICE
Standard Safety Instructions
1. READ THROUGH THE ENTIRE MANUAL BEFORE STARTING MACHINERY. Machinery presents serious
injury hazards to untrained users.
2. ALWAYS USE ANSI APPROVED SAFETY GLASSES WHEN OPERATING MACHINERY. Everyday eye-
glasses only have impact resistant lenses—they are NOT safety glasses.
3. ALWAYS WEAR AN NIOSH APPROVED RESPIRATOR WHEN OPERATING MACHINERY THAT PRODUCES
DUST. Wood dust is a carcinogen and can cause cancer and severe respiratory illnesses.
4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause
permanent hearing damage.
5. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which may
get caught in moving parts. Wear protective hair covering to contain long hair and wear non-slip
footwear.
6. NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL.
Be mentally alert at all times when running machinery.
7. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make
sure operation instructions are safe and clearly understood.
8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the work
area.
9. MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, and remove start switch keys.
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
10. NEVER LEAVE WHEN MACHINE IS RUNNING. Turn power off and allow all moving parts to come to
a complete stop before leaving machine unattended.
11. DO NOT USE IN DANGEROUS ENVIRONMENTS. DO NOT use machinery in damp, wet locations, or
where any flammable or noxious fumes may exist.
12. KEEP WORK AREA CLEAN AND WELL LIT. Clutter and dark shadows may cause accidents.
13. USE A GROUNDED EXTENSION CORD RATED FOR THE MACHINE AMPERAGE. Undersized cords over-
heat and lose power. Replace extension cords if they become damaged. DO NOT use extension cords
for 220V machinery.
14. ALWAYS DISCONNECT FROM POWER SOURCE BEFORE SERVICING MACHINERY. Make sure switch is
in OFF position before reconnecting.
15. MAKE SURE GUARDS ARE IN PLACE AND WORK CORRECTLY BEFORE USING MACHINERY.
16. REMOVE ADJUSTING KEYS AND WRENCHES. Make a habit of checking for keys and adjusting wrench-
es before turning machinery ON.
17. CHECK FOR DAMAGED PARTS BEFORE USING MACHINERY. Check for binding and alignment of
parts, broken parts, part mounting, loose bolts, and any other conditions that may affect machine
operation. Repair or replace damaged parts.
18. USE RECOMMENDED ACCESSORIES. Refer to the instruction manual for recommended accessories.
The use of improper accessories may cause risk of injury.
19. DO NOT FORCE MACHINERY. Work at the speed for which the machine or accessory was designed.
20. SECURE WORKPIECE. Always secure the workpiece with the use of hold-downs, miter gauge, or
fence. Use jigs or fixtures when possible. A secured workpiece reduces the risk of kickback.
21. DO NOT OVERREACH. Keep proper footing and balance at all times.
22. MANY MACHINES WILL EJECT THE WORKPIECE TOWARD THE OPERATOR. Know and avoid condi-
tions that cause the workpiece to "kickback."
23. ALWAYS LOCK MOBILE BASES (IF USED) BEFORE OPERATING MACHINERY.
24. BE AWARE THAT CERTAIN DUST MAY BE HAzARDOUS to the respiratory systems of people and
animals, especially fine dust. Make sure you know the hazards associated with the type of dust you
will be exposed to and always wear a respirator approved for that type of dust.
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
Additional Safety for Wood Lathes
READ and understand this
entire instruction manual
before using this lathe.
Serious personal injury
may occur if safety and
operational information is
not understood and fol-
lowed. DO NOT risk your
safety by not reading!
USE this and other machinery with caution
and respect. Always consider safety first,
as it applies to your individual working
conditions. No list of safety guidelines can
be complete—every shop environment is
different. Failure to follow guidelines could
result in serious personal injury, damage
to equipment or poor work results.
1. EYE/FACE PROTECTION. Always wear an approved face shield when operating this lathe.
2. RESPIRATORY PROTECTION. Always wear a respirator rated for wood dust when using this lathe.
Wood dust may cause allergies or long-term respiratory health problems.
3. MOUNTING WORKPIECE. Before starting the lathe, be certain the workpiece has been properly
embedded on the headstock and tailstock centers or faceplate, and that there is adequate clearance
for full rotation of the workpiece.
4. ADJUSTING TOOL REST. Adjust tool rest to provide proper support for the turning tool in use. Test
tool rest clearance by rotating workpiece by hand before starting lathe.
5. TURNING SPEED. Select the correct turning speed for your operation, and allow the lathe to gain the
desired speed before applying turning tool.
6. USING SHARP CHISELS. Keep lathe chisels properly sharpened and held firmly in position against the
tool rest when using.
7. OPERATING DAMAGED LATHE. Never operate the lathe with damaged or worn parts.
8. ADJUSTMENT/MAINTENANCE. Make sure lathe is disconnected from power and the spindle has come
to a complete stop before starting any inspection, adjustment, or maintenance procedures.
9. STOPPING LATHE. DO NOT attempt to stop the lathe by using your hand against the workpiece, face
plate, or spindle. Allow the lathe to stop on its own.
10. AVOID ENTANGLEMENT. Keep long hair and loose clothing, belts, jewelry away from lathe during
operation. Tie back long hair and button long sleeves. DO NOT wear gloves during lathe operations.
11. FACEPLATE TURNING. When faceplate turning, use lathe chisels on the downward spinning side of
the workpiece only.
12. OUTBOARD TURNING. Always use the tool rest and extension to safely support turning tools when
doing outboard turning. If the provided tool rest assembly will not safely reach the workpiece, use a
free-standing tool rest. Never use the lathe without proper turning tool rest support.
13. WORKPIECE CONDITION. DO NOT turn stock with knots, splits, and other potentially dangerous condi-
tions. Make sure glue joints have high quality bonds and will not fly apart during lathe operation.
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
ELECTRICAL
The machine must be properly set up before it is
safe to operate. DO NOT connect this machine to the
power source until instructed to do so in the "Test
Run" portion of this manual.
110V Operation
The Model W1758 is wired for 110V operation. We recom-
mend connecting this machine to a dedicated circuit with
a verified ground, using the circuit size below as a mini-
mum. Never replace a circuit breaker with one of higher
amperage without consulting a qualified electrician to
ensure compliance with wiring codes.
Figure 1. NEMA 5-15 plug and receptacle.
This machine must be grounded! The electrical cord sup-
plied with this machine comes with a grounding pin. If
your outlet does not accommodate a ground pin, have it
replaced by a qualified electrician.
If you are unsure about the wiring codes in your area
or you plan to connect your machine to a shared cir-
cuit, you may create a fire or circuit overload hazard—
consult a qualified electrician to reduce this risk.
DO NOT work on your electrical system
if you are unsure about electrical
codes and wiring! Seek assistance from
a qualified electrician. Ignoring this
warning can cause electrocution, fire,
or machine damage.
Extension Cords
We do not recommend using an extension cord; however,
if you have no alternative, use the following guidelines:
•
•
•
•
Use a cord rated for Standard Service (S).
Do not use an extension cord longer than 50 feet.
Ensure that the cord has a ground wire and pin.
Use the gauge size listed below as a minimum.
Electrical Specifications
Operating Voltage
Amp Draw
Min. Circuit Size
Plug/Receptacle
Extension Cord
110V Operation
14 Amps
20 Amps
NEMA 5-15
14 Gauge
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
SETUP
Unpacking
This machine has been carefully packaged for safe trans-
portation. If you notice the machine has been damaged
during shipping, please contact your authorized Shop Fox
dealer immediately.
A
C
B
Inventory
The following is a description of the main components
shipped with the Model W1758. Lay the components out
to inventory them.
E
D
Figure 2. Box 1 inventory.
Note: If you can't find an item on this list, check the
mounting location on the machine or examine the pack-
aging materials carefully. Occasionally we pre-install cer-
tain components for safer shipping.
H
G
F
Box 1 Inventory (Figures 2–3)
Qty
A. Lathe Unit ..................................................1
B. Faceplate 6"................................................1
C. Hardware Bag ..............................................1
D. Knockout Tool ..............................................1
E. Flat Wrenches 32mm......................................2
F. Spur Center.................................................1
G. Live Center .................................................1
H. Tool Rest Handle...........................................1
I. Hex Wrenches 3, 4, 6mm ............................1 Ea
J. Cap Screws M8-1.25 x 35mm ............................8
K. Quill locking lever.........................................1
L. Lock Washers 8mm ........................................8
I
J
K
L
Figure 3. Hardware bag inventory.
Box 2 Inventory (Figure 4)
Qty
M. Right Leg....................................................1
N. Left Leg .....................................................1
N
M
Keep machine disconnected
from power until instructed
otherwise.
Figure 4. Box 2 inventory.
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
Machine Placement
Cleaning Machine
•
•
Floor Load: This lathe distributes a heavy
load in a small footprint. Some residential
floors may require additional bracing to
support both machine and operator.
The table and other unpainted parts of your
machine type are coated with a waxy grease
that protects them from corrosion during ship-
ment. Clean this grease off with a solvent clean-
er or citrus-based degreaser. DO NOT use chlo-
rine-based solvents such as brake parts cleaner
or acetone—if you happen to splash some onto a
painted surface, you will ruin the finish.
Working Clearances: Consider existing and
anticipated needs, size of material to be
processed through the machine, and space
for auxiliary stands, work tables or other
machinery when establishing a location for
your wood lathe.
NEVER clean with gasoline
or other petroleum-
based solvents. Most have
low flash points, which
make them extremely
flammable. A risk of
explosion and burning
exists if these products
are used. Serious personal
injury may occur if this
warning is ignored!
•
•
Lighting: Lighting should be bright enough
to eliminate shadow and prevent eye strain.
Electrical: Electrical circuits must be
dedicated or large enough to handle
amperage requirements. Outlets must be
located near each machine, so power or
extension cords are clear of high-traffic
areas. Follow local electrical codes for
proper installation of new lighting, outlets,
or circuits.
ALWAYS work in well-
ventilated areas far from
possible ignition sources
when using solvents to
clean machinery. Many
solvents are toxic when
inhaled or ingested. Use
care when disposing
of waste rags and
towels to be sure they
DO NOT create fire or
environmental hazards.
USE helpers or power lift-
ing equipment to lift this
lathe. Otherwise, seri-
ous personal injury may
occur.
MAKE your shop “child
safe.” Ensure that your
workplace is inaccessible
to youngsters by closing
and locking all entrances
when you are away. NEVER
allow untrained visitors in
your shop when assem-
bling, adjusting or operat-
ing equipment.
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
Mounting to Shop Floor
Although not required, we recommend that you mount
your new machine to the floor. Because this is an optional
step and floor materials may vary, floor mounting hard-
ware is not included. Generally, you can either bolt
your machine to the floor or mount it on machine feet.
Both options are described below. Whichever option you
choose it will be necessary to use a precision level to
level your machine.
Bolting to Concrete Floors
Lag shield anchors with lag bolts and anchor studs (Figure
5) are two popular methods for anchoring an object to a
concrete floor. We suggest you research the many options
and methods for mounting your machine and choose the
best that fits your specific application.
Figure 5. Typical fasteners for mounting
to concrete floors.
NOTICE
Anchor studs are stronger and more permanent alter-
natives to lag shield anchors; however, they will stick
out of the floor, which may cause a tripping hazard if
you decide to move your machine at a later point.
Using Machine Feet
Using machine feet, shown in Figure 6, gives the advan-
tage of fast leveling and vibration reduction. The large
size of the foot pads distributes the weight of the
machine to reduce strain on the floor.
Figure 6. Machine foot example.
Assembly
To assemble your lathe, do these steps:
1. Stand the right and left legs upright approximately
41" apart, and get them reasonably aligned, as
shown in Figure 7.
2. Using the help of assistants, carefully lift the lathe
onto the stands and align the mounting holes.
Note: The headstock end is the heaviest and usually
requires two people lifting at that end.
Figure 7. Legs approximately 41" apart.
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
3. Using the 6mm hex wrench, secure the lathe to the
legs with the eight cap screws and lock washers, as
shown in Figure 8.
4. Install the handle into the tool rest, as shown in
Figure 9.
5. Align the quill keyway with the entry hole of the
quill lock lever (see Figure 10), then install the
lever into the tailstock so that the end of it mates
with the quill keyway.
Figure 8. Securing lathe to legs.
Note: Make sure the dog-end of the lock lever fits
into the quill keyway so that the quill can move in
and out of the tailstock without rotating.
To safely secure a center in the tailstock quill, the
quill locking lever must be aligned with the quill
keyway and fully tightened. Failure to follow this
procedure could result in the spinning workpiece or
center being thrown from the lathe, causing death
or serious personal injury.
Figure 9. Installing tool rest handle.
6. Secure the digital readout to the top of the head-
stock, as shown in Figure 11.
Quill
Keyway
Quill Locking
Lever
Figure 10. Quill locking lever installed.
Figure 11. Digital readout installed onto
the headstock (viewed from the back).
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
Test Run
W1758 Owner's Manual (Mfg. Since 3/10)
Test Run
Once the assembly is complete, test run your machine to
make sure it runs properly and is ready for regular opera-
tion.
Tie back long hair, roll
up long sleeves, and
remove loose clothing,
jewelry, or gloves to
prevent getting caught
in moving parts.
The test run consists of verifying the following: 1) The
motor powers up and runs correctly, and 2) the switch
disabling mechanism works correctly.
If, during the test run, you cannot easily locate the source
of an unusual noise or vibration, stop using the machine
immediately, then review Troubleshooting on Page 30.
If you still cannot remedy a problem, contact our Tech
Support at (360) 734-3482 for assistance.
To test run the machine, do these steps:
1. Make sure you understand the safety instructions at
the beginning of the manual and that the machine is
setup properly.
2. Make sure all tools and objects used during setup are
cleared away from the machine.
3. Connect the machine to the power source.
4. Turn the lathe ON by lifting up on the ON/OFF
switch, and verify that it operates correctly.
— When operating correctly, the machine runs
smoothly with little or no vibration or rubbing
noises.
— Investigate and correct strange or unusual noises
or vibrations before operating the machine fur-
ther. Always disconnect the machine from power
when investigating or correcting potential prob-
lems.
5. Turn the machine OFF by pushing down on the ON/
OFF switch.
6. Remove the switch disabling key (see Figure 12).
7. Try to start the machine with the switch.
— If the machine does not start, the switch disabling
feature is working as designed.
— If the machine starts, immediately stop the
machine. The switch disabling feature is not work-
ing correctly. Call Tech Support for help.
Figure 12. Removing lockout key from
switch.
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
OPERATIONS
General
This lathe will perform many types of operations that are
beyond the scope of this manual. Many of these operations
can be dangerous or deadly if performed incorrectly.
The instructions in this section are written with the under-
standing that the operator has the necessary knowledge
and skills to operate this machine. If at any time you are
experiencing difficulties performing any operation, stop
using the machine!
READ and understand this entire instruc-
tion manual before using this machine.
Serious personal injury may occur if
safety and operational information is not
understood and followed. DO NOT risk
your safety by not reading!
If you are an inexperienced operator, we strongly recom-
mend that you read books, trade articles, or seek training
from an experienced wood lathe operator before perform-
ing any unfamiliar operations. Above all, your safety
should come first!
DO NOT investigate problems or adjust
the machine while it is running. Wait
until the machine is turned OFF,
unplugged and all working parts
have come to a complete stop before
proceeding!
Always wear an approved safety face
shield and a respirator when operating
this machine. Failure to comply may
result in serious personal injury.
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
Adjusting Headstock
The Model W1758 headstock can be positioned anywhere
along the bed and swiveled 360°.
To position the headstock along the length of the lathe
bed, do these steps:
1. DISCONNECT THE LATHE FROM POWER!
2. Loosen the headstock locking lever (see Figure 13).
3. Position the headstock along the lathe bed and
secure it in place by tightening the locking lever.
Figure 13. Headstock locking lever.
Note: The large clamping hex nut underneath the
headstock may require occasional adjusting to
ensure proper clamping pressure of the headstock to
the bed.
To swivel the headstock, do these steps:
1. DISCONNECT THE LATHE FROM POWER!
2. Loosen the headstock locking handle (see Figure
13).
3. Pull out the headstock rotation locking pin (see
Figure 14), and rotate the headstock in place.
4. Release the locking pin to secure the headstock in
one of the five pre-set positions: 0°, 60°, 90°, 120°,
or 180°.
5. Re-tighten the headstock locking lever.
Figure 14. Headstock rotation locking pin.
Always keep the headstock firmly locked in place
with both the headstock locking lever and the head-
stock rotation locking pin during lathe operation.
Otherwise, the headstock could unexpectedly move
and send the moving workpiece, spindle, or face-
plate toward you. Failure to heed this warning could
result in serious personal injury.
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
Adjusting Tailstock
The tailstock is equipped with a cam-action clamping sys-
tem to secure it to the lathe bed. When the locking lever
is tightened, a locking plate lifts up underneath the bed
and secures the tailstock in place.
To position the tailstock along the length of the bed,
do these steps:
1. Loosen the tailstock locking lever (see Figure 15),
and move the tailstock in position.
Figure 15. Tailstock locking lever.
2. Re-tighten the locking lever to secure the tailstock
in place.
Always keep the tailstock firmly
locked in place with the tailstock
locking lever during lathe operation.
Otherwise, the tailstock could unex-
pectedly move and send the spinning
workpiece or center toward you.
Failure to heed this warning could
result in death or serious personal
injury.
Note: The large clamping hex nut underneath the
tailstock may require occasional adjusting to ensure
proper clamping pressure of the headstock to the
bed.
Adjusting Tool Rest
The Model W1758 comes with a three-way adjustable tool
rest (see Figure 16).
•
•
•
Use the base locking lever to position the tool rest
along the length of the bed.
Tool Rest
Locking Lever
Use the extension locking lever to secure the tool
rest a working distance from the bed or workpiece.
Use the tool rest locking lever to adjust the height
of the tool rest relative to the workpiece.
Base Locking
Lever
Extension Locking
For safety and good turning results, we recommend the
tool rest be positioned approximately 1⁄4" away from the
workpiece, and approximately 1⁄8" above the workpiece
center line (see Figure 17).
Lever
Figure 16. Tool rest controls.
Workpiece
1/4"
Distances
Always keep the tool rest assembly firmly locked in
place during lathe operation. Otherwise, the tool
rest could unexpectedly slip and draw the turning
tool and your hand into the spinning workpiece.
Failure to heed this warning could result in serious
personal injury.
1/8"
Center Line
Tool Rest
Figure 17. Tool rest position relative to
workpiece.
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
Headstock Center
W1758 Owner's Manual (Mfg. Since 3/10)
Installing/Removing
Headstock Center
Before beginning any turning opera-
tion, make sure the headstock
The included spur center installs into the headstock spin-
dle with an MT#2 tapered fit.
and tailstock centers are properly
aligned. Refer to Aligning Headstock
& Tailstock Centers on Page 28 for
instructions on this procedure. Failure
to heed this warning could result in
the spinning workpiece being thrown
from the lathe resulting in death or
serious personal injury.
To install the headstock spur center, do these steps:
1. DISCONNECT THE LATHE FROM POWER!
2. Move the tailstock and tool rest to a safe working
distance from the headstock.
3. If the faceplate is installed, remove it (refer to Page
20 for instructions).
4. Make sure the mating surfaces of the spur center and
spindle are free of debris and oily substances before
inserting the center.
5. Insert the tapered end of the center into the spin-
dle, and push it in with a quick, firm motion (see
Figure 18).
6. Make sure the spur center is securely installed
by attempting to pull it out by hand—a properly
installed center will not pull by hand.
Figure 18. Installing the headstock center.
To remove the headstock spur center, do these steps:
1. DISCONNECT THE LATHE FROM POWER!
2. Hold a clean rag under the spindle or wear a glove
to catch the spur center when you remove it.
3. Insert the knockout tool through the outboard end of
the spindle and firmly tap the center, catching it as
it falls (see Figure 19).
Knockout
Tool
Figure 19. Removing the headstock
center.
-18-
Download from Www.Somanuals.com. All Manuals Search And Download.
Tailstock Center
W1758 Owner's Manual (Mfg. Since 3/10)
Quill Locking Lever
Installing/Removing
Tailstock Center
The included live center installs into the tailstock quill
with an MT#2 tapered fit.
To install the tailstock live center, do these steps:
1. Move the tailstock to a safe working distance away
Quill
Keyway
from the tool rest and headstock.
Handwheel
2. Loosen the quill locking lever, then rotate the quill
handwheel clockwise until the quill extends out from
the tailstock about 1" (see Figure 20).
Figure 20. Installing the tailstock center.
3. Make sure the mating surfaces of the live center and
quill are free of debris and oily substances before
inserting the center.
Always lock the quill in place during
lathe operation. Before tightening the
quill locking lever, it must be properly
aligned with the keyway on the quill.
Otherwise, the spinning workpiece
could be thrown from the lathe caus-
ing death or serious personal injury.
4. Insert the tapered end of the center into the quill
with a quick, firm motion.
5. Make sure the center is secure by attempting to pull
it out by hand—a properly installed center will not
pull out by hand.
6. Tighten the quill locking lever to hold the quill and
center in place.
Note: Make sure the quill locking lever is aligned with
the quill keyway to prevent the quill from rotating
during use.
To remove the tailstock live center, do these steps:
1. Loosen the quill locking lever.
2. Hold a clean rag under the center or wear a glove to
catch the center when you remove it.
3. Rotate the quill handwheel counterclockwise—the
quill will retract back into the tailstock causing the
center to be forced out.
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Faceplate
W1758 Owner's Manual (Mfg. Since 3/10)
Installing/Removing
Faceplate
The faceplate is used for removing material from the face
of the workpiece, such as in hollowing operations. The
faceplate can be installed only if the center has been
removed from the headstock spindle.
To install the faceplate onto the spindle, do these
steps:
1. DISCONNECT THE LATHE FROM POWER!
Figure 21. Tightening faceplate onto
2. If the headstock center is installed, remove it (refer
to Page 18 for instructions).
headstock spindle.
3. Thread the faceplate onto the headstock spindle.
4. Using the two included 34mm flat wrenches, tighten
the faceplate, as shown in Figure 21.
Always make sure that the workpiece
is firmly attached to the faceplate and
the faceplate is fully tightened onto
the headstock spindle before turning
the lathe ON. Otherwise the spinning
workpiece or faceplate could fly off
the spindle and cause death or seri-
ous personal injury.
Note: To remove the faceplate, reverse Steps 3–4.
For detailed instructions on mounting a workpiece to the
faceplate, refer to Faceplate Turning on Page 24.
-20-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
Selecting Turning Tools
Lathe chisels come in a variety of shapes and sizes, and
usually fall into five major categories. See Figures 22–25
for some examples.
Gouges: Mainly used for rough cutting, detail cutting, and
cove profiles. The rough gouge is a hollow, double-ground
tool with a round nose, and the detail gouge is a hollow,
double-ground tool with either a round or pointed nose.
Skew Chisels: A very versatile tool that can be used for
planing, squaring, V-cutting, beading, and parting off. The
skew chisel is flat, double-ground with one side higher
than the other—usually at an angle of 20°–40°.
Figure 22. Example of a gouge.
Scrapers: Typically used where access for other tools is
limited, such as hollowing operations. This is a flat, dou-
ble-ground tool that comes in a variety of profiles (round
nose, spear point, square nose, etc.) to match many dif-
ferent contours.
Parting Tools: Used for sizing and cutting off work. This
is a flat tool with a sharp pointed nose that may be single
or double-ground.
Figure 23. Example of a skew chisel.
Specialty Tools: These unique, special function tools aid
in hollowing, bowl making, cutting profiles, etc.
Refer to Accessories on Page 26 for examples of recom-
mended wood chisels.
Figure 24. Example of a round nose
scraper.
Figure 25. Example of a parting tool.
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
Spindle Turning
W1758 Owner's Manual (Mfg. Since 3/10)
Spindle Turning
Spindle turning is the operation performed when a
workpiece is mounted between the headstock and
tailstock centers (see Figure 26).
Before beginning any turning operation, make sure
the headstock and tailstock centers are properly
aligned. Refer to Aligning Headstock & Tailstock
Centers on Page 28 for instructions on this proce-
dure. Failure to heed this warning could result in
the spinning workpiece being thrown from the lathe
resulting in death or serious personal injury.
Figure 26. Typical spindle turning
operation.
To set up a spindle turning operation, do these steps:
Workpiece
1. Find the center point of both ends of your workpiece
by drawing diagonal lines from corner to corner
across the end of the workpiece (see Figure 27).
Pencil Lines
Marked
Diagonally
Across Corners
2. Using a wood mallet, tap the point of the spur cen-
ter into the center of the workpiece on both ends,
leaving an indented center mark.
3. Use a 1⁄4" drill bit to drill a 1⁄4" deep hole at the
center mark on the workpiece end to be mounted on
the headstock spur center.
Workpiece
Center
Figure 27. Workpiece marked diagonally
from corner to corner to determine the
center.
4. To help embed the spur center into the workpiece,
cut 1⁄8" deep saw kerfs into the same workpiece end
along the diagonal lines marked in Step 1.
5. If your workpiece is over 2" x 2", cut the corners off
the workpiece length-wise to make turning the cor-
ners safer and easier.
1/4"
6. Drive the spur center into the workpiece end center
mark with a wood mallet to embed it at least 1⁄4
into the workpiece (see Figure 28).
"
7. With the workpiece still attached, insert the spur
center into the headstock spindle (refer to Installing
Headstock Center on Page 18 for instructions).
Figure 28. Spur center properly
embedded.
-22-
Download from Www.Somanuals.com. All Manuals Search And Download.
Tool Rest Height
W1758 Owner's Manual (Mfg. Since 3/10)
8. Install the live center into the tailstock quill, and
lock the quill in place with the quill locking lever
(refer to Installing Tailstock Center on Page 19 for
instructions).
Workpiece
1/4"
Distances
1/8"
Center Line
9. Slide the tailstock toward the workpiece until the
point of the tailstock center touches the workpiece
end center mark, then secure the tailstock in place
with the tailstock locking lever.
Tool Rest
10. Loosen the quill locking lever and rotate the quill
handwheel clockwise to push the tailstock center
into the workpiece at least 1⁄4".
Figure 29. Relative position of tool rest to
workpiece.
11. Position the tool rest approximately 1⁄4" away from
the workpiece, and approximately 1⁄8" above the
workpiece center line (see Figure 29).
DO NOT press the workpiece too
firmly with the tailstock center or
the bearings will bind and over-
heat. Likewise, DO NOT leave the
workpiece too loose or the workpiece
will spin off the lathe. Use good rea-
son and care, otherwise, serious per-
sonal injury could result.
12. Before turning the lathe ON, rotate the workpiece
by hand to ensure that there is safe clearance on all
sides.
Spindle Turning Safety Tips:
•
When turning the lathe ON, stand away from the
vertical path of the spinning workpiece until the
lathe reaches full speed and you can verify that the
lathe will not throw the workpiece.
•
•
Use the slowest speed when starting the lathe.
Always keep the turning tool rest-
ing on the tool rest when preparing
to make contact with the workpiece
and when it is in contact with the
workpiece. Otherwise, the spin-
ning workpiece could force the tool
towards you at a high rate of speed,
or entangle your hands with the mov-
ing workpiece. Failure to heed this
warning could result in serious per-
sonal injury.
Select the right speed for the size of the workpiece
you are turning:
— Use the slower speeds for large workpieces of
diameters of 4" and over, and for rough cutting.
— Use the middle range speeds for workpiece diam-
eters of 2–4".
— Use the faster speeds for workpieces under 2", and
for finish turning.
•
•
Keep the turning tool on the tool rest the ENTIRE
time that it is approaching the workpiece and it is in
contact the workpiece.
Learn the correct techniques for each tool you will
use. If you are unsure about how to use the lathe
tools, read books or magazines about lathe tech-
niques, and seek training from experienced and
knowledgeable lathe users.
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
Faceplate Turning
W1758 Owner's Manual (Mfg. Since 3/10)
Faceplate Turning
Faceplate turning is when a workpiece is mounted to the
faceplate that, in turn, is secured to the headstock spin-
dle. This type of turning is usually done with open-faced
workpieces like bowls or plates (see Figure 30).
To mount the workpiece onto the faceplate, do these
steps:
1. Mark the center of the workpiece back, as in Spindle
Turning on Page 22.
Figure 30. Typical faceplate turning
operation.
Note: Cut off the excess corners of the workpiece to
make it as close to "round" as possible.
2. Use the mark made from Step 1 to center the face-
plate on the workpiece back, and attach it with
wood screws that do not have tapered heads (see
Figures 31 & 32).
3. Thread and secure the faceplate onto the headstock
spindle (refer to Installing Faceplate on Page 20 for
detailed instructions).
If wood screws cannot be placed in the workpiece, then
the faceplate can be mounted to a backing block that is
securely glued to the workpiece.
Figure 31. Typical attachment of
faceplate to workpiece (shown with
backing block).
To mount your workpiece to a backing block, do these
steps:
Correct
Incorrect
1. Make the backing block from a piece of scrap wood
that is flat on both sides, and is free of knots and
splits.
2. Locate and mark the center of both the workpiece
and the backing block.
Figure 32. Correct and incorrect
screw types for mounting faceplate to
workpiece.
3. Drill a 1⁄4" hole completely through the backing block
at its center.
4. Looking through the hole in the backing block to line
it up with the center of the workpiece, glue and
clamp the backing block to the workpiece.
NOTICE
Only use tap screws or wood screws with
non-tapered heads (see Figure 32) to
attach the faceplate to the workpiece.
DO NOT use drywall screws or screws
with tapered heads because they can
split the faceplate, or the screws may
snap off during lathe operation.
Note: Allow the glue joint to completely cure
according to the manufacturer's instructions.
-24-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
Outboard Turning
Outboard turning is a variation of faceplate turning and
is usually done when stock diameter is greater than 12".
For the size of the Model W1758 and its minimum turn-
ing speed, we recommend not exceeding a maximum
workpiece diameter of 17".
Figure 33 depicts the lathe setup at 90° and using the
provided tool rest extension. Figure 34 shows the head-
stock setup for outboard turning at 180°.
Figure 33. Headstock positioned outboard
It is important for safety and performance to use the pro-
vided tool rest extension in a manner that will offer the
greatest stability and range for your turning tool. If this
tool rest assembly will not work for your operation, you
must use a free-standing tool rest (not supplied).
at 90°.
Sanding/Finishing Using
the Lathe
The lathe can be used for finishing procedures after the
turning operations are complete, such as sanding, polish-
ing, and applying finishes by hand (see Figure 35).
Figure 34. Headstock positioned outboard
at 180°.
Note: Whenever performing finishing procedures to your
workpiece, remove the tool rest to avoid entanglement.
Use the slowest speeds for safer control and better
results.
Sandpaper
Wrapping sandpaper or other
finishing materials completely
around the workpiece could
pull your hands into the spin-
ning workpiece and cause
personal injury. Never wrap
anything completely around
the spinning workpiece.
Workpiece
Figure 35. Typical sanding operation on a
lathe.
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
W1758 Owner's Manual (Mfg. Since 3/10)
ACCESSORIES
Wood Lathe Accessories
The following wood lathe accessories may be available through your local Woodstock International Inc.
Dealer. If you do not have a dealer in your area, these products are also available through online deal-
ers. Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of deal-
ers at: 1-800-545-8420 or at sales@woodstockint.com.
The D1090 Steelex 3-Jaw Chuck for Wood Lathes is a "must have"
for the serious wood turner. This 3-jaw chuck is a self-centering style
chuck used mostly for round work. All three jaws tighten together
to aid in centering the workpiece. Jaws are reversible for expanded
work holding capacity. Threaded insert required for mounting, such
as the D1098 Steelex 1" x 8 TPI RH threaded insert.
The D1089 Steelex 4-Jaw Chuck for Wood Lathes is another "must
have" for the serious wood turner. This 4-jaw chuck is an indepen-
dent type chuck that is used for square and odd-shaped pieces. Each
jaw tightens individually and can be turned around to hold larger
dimension workpieces. Threaded insert required for mounting, such
as the D1098 Steelex 1" x 8 TPI RH threaded insert.
The D2304 Steelex Plus 6-Piece Deluxe Lathe Chisel Set features
beefy ash handles for unsurpassed control, brass ferrules, and high-
speed steel blades. Includes: a 17" long 13⁄16" parting tool, 13⁄16" round
nose, 3⁄8" gouge, 19" long 1" skew, 5⁄8" gouge, and a 223⁄4" long 3⁄8
"
gouge. Comes in a beautiful red blow-molded carrying case.
The D2250 Steelex 5-Piece Turning Chisel Set is for those fine
detail turning operations. This set features well balanced hardwood
handles and high carbon steel cutting edges. Includes: a 1⁄16" radius
gouge, 1⁄8" radius gouge, 3⁄16" parting tool, 1⁄4" spear point, and a 1⁄4
skew. All tools are 101⁄2" overall in length.
"
-26-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
MAINTENANCE
General
Regular periodic maintenance on your machine will
ensure its optimum performance. Make a habit of
inspecting your machine each time you use it.
Check for the following conditions and repair or
replace when necessary:
•
•
•
•
•
Loose mounting bolts.
Worn switch.
Worn or damaged cords and plugs.
Damaged V-belt.
Any other condition that could hamper the safe
operation of this machine.
MAKE SURE that your machine is
unplugged during all maintenance pro-
cedures! If this warning is ignored, seri-
ous personal injury may occur.
Lubrication
Cleaning
Since all bearings for the Model W1758 are
sealed and permanently lubricated, simply
leave them alone until they need to be
replaced. Do not lubricate them.
Cleaning the Model W1758 is relatively easy. Vacuum
excess wood chips and sawdust, and wipe off the remain-
ing dust with a dry cloth. If any resin has built up, use a
resin dissolving cleaner to remove it.
Wipe a lightly oiled shop rag on the outside
of the headstock spindle. DO NOT allow any
oil to get on the inside mating surface of
the spindle.
Remove any debris or oily substances from the inside of
the spindle and quill.
Use the quill handwheel to extend the
tailstock quill all the way out, and apply
a thin coat of white lithium grease to the
outside of the quill. DO NOT allow any
lubricant to get on the inside mating sur-
face of the quill.
Lathe Bed
Protect the unpainted cast iron lathe bed by wiping it
clean after every use—this ensures moisture from wood
dust does not remain on the bare metal surfaces. Keep
your lathe bed rust-free with regular applications of qual-
ity lubricants.
Tailstock
To disassemble the tailstock for cleaning, loosen the set
screw above the handwheel, then completely unthread
the handwheel from the threads of the quill. Except for
the live center, thoroughly clean all of the unpainted
parts with mineral spirits and apply a thin coat of light
machine oil to these surfaces.
When re-assembling the tailstock, thread the handwheel
back onto the quill, tighten down the set screw that
secures it, then back the screw off one full turn so that
the handwheel can freely rotate.
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
V-Belt
Align Headstock &
Tailstock
W1758 Owner's Manual (Mfg. Since 3/10)
SERVICE
General
This section covers the most common service adjustments
or procedures that may need to be made during the life
of your machine.
If you require additional machine service not included
in this section, please contact Woodstock International
Technical Support at (360) 734-3482 or send e-mail to:
MAKE SURE that your machine is
unplugged during all service proce-
dures! If this warning is ignored, seri-
ous personal injury may occur.
Aligning Headstock &
Tailstock Centers
To ensure accurate and safe results, make sure that the
headstock and tailstock centers are aligned before you
begin your lathe operation.
To align the headstock and tailstock centers, do these
steps:
1. DISCONNECT THE LATHE FROM POWER!
2. With the headstock and tailstock centers installed,
slide the tailstock up to the headstock.
Figure 36. Center tips touching to ensure
3. Loosen the headstock locking lever and swivel the
headstock so that the tips of the centers touch, as
illustrated in Figure 36, then lock the headstock
securely in place.
proper alignment.
Changing V-Belt
To change the V-belt, do these steps:
1. DISCONNECT THE LATHE FROM POWER!
2. Remove the belt safety cover from the back of the
lathe.
3. Pull the motor pulley plates apart so that the V-belt
will slip down to the motor arbor—this will loosen
the V-belt tension (see Figure 37).
Figure 37. Changing the V-belt.
4. While keeping the tension off the V-belt, roll it off
the spindle pulley and remove it.
5. Install the new V-belt by reversing Steps 3–4.
-28-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
Electrical Components & Wiring Diagram
Hot
Bk
110 VAC
NEMA 5-15 Plug
(As Recommended)
Wt
Ground
Gr
Neutral
Wt
Bk
Gr
Bk
Paddle
Switch
Wt
Gr
Wt
Bk
Digital Readout
Motor
Rd
Bk
Capacitor
100MFD 250VAC
Spindle Speed Sensor
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
W1758 Owner's Manual (Mfg. Since 3/10)
Troubleshooting
This section covers the most common problems and corrections with this type of
machine. WARNING! DO NOT make any adjustments until power is disconnected and
moving parts have come to a complete stop!
Motor & Electrical
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
Lathe will not start, or it
growls on start up.
1. Power supply fuse or circuit break- 1. Disconnect power, and inspect circuit for electrical
er has tripped.
shorts and repair. Replace circuit breaker if it is
old or has tripped many times.
2. Motor fan cover is dented, stop-
ping the fan from being able to
spin.
2. Replace or adjust fan cover; inspect motor fan and
replace if damaged.
3. Paddle switch is broken or faulty.
3. Disconnect power, and use an ohmmeter to check
switch terminals for continuity, and replace switch
if required.
4. Start capacitor is at fault.
5. Motor is at fault.
4. Replace start capacitor.
5. Replace motor.
Fuses or circuit breakers
trip open.
1. Short circuit in line cord or plug.
1. Inspect cord or plug for damaged insulation and
shorted wires, and replace extension cord.
2. Replace or adjust fan cover; inspect motor fan and
replace if damaged.
2. Short circuit in motor or loose
connections.
3. Incorrect fuses or circuit breakers 3. Install correct fuses or circuit breakers.
in power supply.
Vibration noise while
machine is running; noise
changes when speed is
changed.
1. V-belt cover loose.
1. Tighten the four screws securing V-belt cover;
if necessary, install a soft, vibration dampening
material between V-belt cover and headstock.
2. V-belt cover bent or dented and is 2. Remove V-belt cover and inspect for dents, bends,
making contact with motor pulley
or V-belt.
or indications of rubbing. Tap out dents with rub-
ber mallet, bend back into proper shape, or shim
away from the motor pulley.
3. Bad spindle bearing(s).
1. Dented motor fan cover.
3. Replace spindle bearing(s).
Vibration noise while
machine is running; noise
remains constant when
speed is changed.
1. Replace or adjust fan cover; inspect motor fan and
replace if damaged.
2. Bad spindle bearing(s).
2. Replace spindle bearing(s).
-30-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
Lathe Operation
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
Bad surface finish.
1. Wrong spindle speed.
2. Dull chisel or wrong chisel being
used for operation.
1. Use trail-and-error to find better spindle speed.
2. Sharpen chisel or try a different chisel.
Tailstock moves.
1. Tailstock mounting bolt loose.
2. Bed surface is oily or greasy.
1. Tighten.
2. Clean bed surface to remove excess oil/grease.
Excessive vibration.
1. Workpiece mounted incorrectly.
1. Re-mount workpiece, making sure centers are
aligned and are fully embedded in true center of
workpiece.
2. Workpiece warped, out of round,
or is flawed.
2. Cut workpiece to correct, or use a different
workpiece.
3. Spindle speed is set too fast for
mounted workpiece.
3. Reduce spindle speed.
4. Lathe is resting on uneven surface. 4. Shim legs or adjust machine feet to ensure lathe is
even and stable on the floor.
5. Motor mounting bolts are loose.
6. V-belt is worn or damaged.
7. Spindle bearing(s) are worn.
5. Tighten motor mounting bolts.
6. Replace V-belt (refer to Page 28).
7. Replace spindle bearing(s).
Chisels grab or dig into
workpiece.
1. Tool rest adjusted too low.
2. Tool rest set too far from
workpiece.
1. Adjust tool rest higher (refer to Page 23).
2. Move tool rest closer to workpiece (refer to Page
23).
3. Wrong chisel/tool being used.
3. Use correct chisel/tool; educate yourself by read-
ing books, trade magazines, or seeking help from
an experienced lathe operator.
4. Chisel/tool is dull.
4. Sharpen or replace chisel/tool being used.
Inaccurate turning results
from one end of the
workpiece to the other.
1. Headstock and tailstock are not
properly aligned with one another.
1. Re-align headstock and tailstock to one another
(refer to Page 28).
Cannot remove tapered
tool from tailstock barrel.
1. Tailstock quill not fully retracted
into tailstock.
1. Turn quill handwheel until it forces tapered tool
out of quill.
2. Debris or oily substance not
removed from quill and tapered
tool mating surfaces before
installing.
2. Always make sure the mating surfaces of the quill
and tapered tool are free from debris and oily sub-
stances.
-31-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
PARTS
-32-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
Parts List
REF
101
102
103
104
PART #
XPS05M
X1758102
XPB26M
DESCRIPTION
PHLP HD SCR M5-.8 x 8
MOTOR COVER
HEX BOLT M8-1.25 X 30
LOCK WASHER 8MM
REF
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
PART #
DESCRIPTION
XPR58M
EXT RETAINING RING 24MM
SPEED CHANGE LABEL
SPEED CONTROL LEVER ASSY
PHLP HD SCR M5-.8 X 12
PHLP HD SCR M4-.7 X 12
PIVOT LOCKING PIN
HEADSTOCK PIVOT BOLT
PIVOT BASE
BED CLAMP PLATE
X1758141
X1758142
XPS08M
XPLW04M
105V2 X1758105V2 MOTOR 2HP 110V 60HZ V2.10.08
105-1V2 X1758105-1V2 MOTOR FAN COVER V2.10.08
105-2V2 X1758105-2V2 MOTOR FAN V2.10.08
105-4V2 X1758105-4V2 S CAPACITOR 100M 250V V2.10.08
105-5V2 X1758105-5V2 MOTOR JUNCTION BOX V2.10.08
105-6V2 X1758105-6V2 JUNCTION BOX COVER V2.10.08
XPS02M
X1758145
X1758146
X1758147
X1758148
XPN29M
HEX NUT M18-2.5
106
107
108
109
110
111
112
113
114
115
115-1
115-2
115-4
116
116-1
117
118
119
120
121
122
123
124
125
126
127
128
129
129-1
130
131
132
133
134
135
136
137
138
139
X1758106
XPR12M
X1758108
X1758109
XPR38M
XP6007ZZ
X1758112
XPR12M
X1758114
X1758115
X1758115-1
D2751
KNOCKOUT TOOL
XPR58M
EXT RETAINING RING 24MM
HEADSTOCK ECCENTRIC SHAFT
LEVER
SET SCREW M8-1.25 X 25
HEX NUT M8-1.25
EXT RETAINING RING 35MM
CENTER-DRILLED SET SCR M6-1 X 10
MOTOR PULLEY SET
INT RETAINING RING 62MM
BALL BEARING 6007ZZ
SHIFTING LEVER BRACKET
EXT RETAINING RING 35MM
RACK
X1758151
X1758152
XPSS21M
XPN03M
X1758157
XPCAP12M
XPR08M
X1758160
X1758161
X1758162
XPN29M
X1758164
X1758165
X1758166
XPR08M
BED
CAP SCREW M8-1.25 X 40
EXT RETAINING RING 19MM
BALL LEVER
TOOL REST ECCENTRIC SHAFT
TOOL REST BASE
SWITCH ASSEMBLY
SWITCH BOX
PADDLE SWITCH W/KEY
SWITCH BOX PLATE
HEADSTOCK CASTING
HEADSTOCK ASSEMBLY
KEY 4 X 4 X 80
HEX NUT M18-2.5
X1758115-4
X1758116
X1758116-1
XPK93M
TOOL REST CLAMP PLATE
TOOL REST PIVOT BOLT
LOCK HANDLE ASSY M10-1.5 X 15
EXT RETAINING RING 19MM
LOCK HANDLE ASSY M10-1.5 X 15
TOOL REST EXTENSION ARM
TOOL REST
XPR06M
EXT RETAINING RING 16MM
MOTOR SHAFT SLEEVE
COMPRESSION SPRING
SPINDLE PULLEY SET
V-BELT M24 3L240
EXT RETAINING RING 16MM
STRAIN RELIEF M20-1.5
POWER WIRE 16G 3W 5-15 PLUG
PHLP HD SCR M6-1 X 10
PHLP HD SCR M6-1 X 10
DIGITAL READOUT BRACKET
DIGITAL READOUT ASSEMBLY
RPM SENSOR
X1758166
X1758169
X1758170
X1758171
X1758119
X1758120
X1758121
XPVM24
TAILSTOCK LIVE CENTER MT#2
172V2 X1758172V2 TAILSTOCK LOCK LEVER V2.11.09
173V2A X1758173V2A TAILSTOCK ASSEMBLY V2.11.09
173V2 X1758173V2 TAILSTOCK CASTING V2.11.09
174V2 X1758174V2 TAILSTOCK QUILL V2.11.09
175V2 X1758175V2 QUILL LOCK HANDLE ASSY V2.11.09
176V2 X1758176V2 HANDWHEEL SET SCREW V2.11.09
177V2 X1758177V2 TAILSTOCK HANDWHEEL V2.11.09
178V2 X1758178V2 HANDWHEEL HANDLE V2.11.09
180V2 X1758180V2 TAILSTOCK PIVOT BOLT V2.11.09
181V2 X1758181V2 TAILSTOCK CLAMP PLATE V2.11.09
XPR06M
X1758124
X1758125
XPS68M
XPS68M
X1758128
X1758129
X1758129-1
X1758130
X1758131
X1758132
X1758133
XPK93M
XP6205ZZ
XPR26M
XPR26M
XP6205ZZ
XPR11M
FLAT WRENCH 32MM
SPUR CENTER MT#2
FACEPLATE 6"
SPINDLE 1" x 8"
KEY 4 X 4 X 80
182V2 XPN29M
HEX NUT M18-2.5
PHLP HD SCR M5-.8 X 12
BED END PLATE
LOCK WASHER 8MM
HEX NUT M8-1.25
STAND LEG
183
184
185
186
187
200
201
XPS08M
X1758184
XPLW04M
XPN03M
X1758187
X1758200
XPSS04M
BALL BEARING 6205ZZ
INT RETAINING RING 52MM
INT RETAINING RING 52MM
BALL BEARING 6205ZZ
EXT RETAINING RING 25MM
TAILSTOCK LEADSCREW V2.11.09
SET SCREW M6-1 X 12
-33-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
Label Placement
Safety labels warn about machine hazards and how to prevent machine damage or injury. The
owner of this machine MUST maintain the original location and readability of all labels on this
machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the
machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www.
shopfoxtools.com to order new labels.
194
191
189
190
192
196
199
197
198
195
193
REF PART #
DESCRIPTION
MACHINE ID LABEL
DIGITAL READOUT LABEL
ELECTRICITY LABEL
SPEED CHANGE NOTICE LABEL
READ MANUAL LABEL
DISCONNECT POWER LABEL
REF PART #
DESCRIPTION
ENTANGLEMENT WARNING LABEL
XPPAINT-1 SHOP FOX WHITE TOUCH-UP PAINT
189
190
191
192
193
194
X1758189
X1758190
X1758191
X1758192
X1758193
X1758194
195
196
197
198
199
X1758195
X1758197
X1758198
X1758199
BLACK PIN STRIPE LABEL
SHOP FOX NAMEPLATE
MODEL NUMBER LABEL
-34-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1758 Owner's Manual (Mfg. Since 3/10)
Warranty Registration
Name___________________________________________________________________________________
Street __________________________________________________________________________________
City _________________________State___________________________Zip________________________
Phone #______________________Email___________________________Invoice #___________________
Model #_________Serial #______________Dealer Name__________________Purchase Date___________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us
develop better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
_____ Advertisement
_____ Friend
_____ Website
____ Local Store
____ Other:
_____ Mail Order Catalog
2. How long have you been a woodworker/metalworker?
_____ 0-2 Years
_____ 2-8 Years
____8-20 Years
_____20+ Years
3. How many of your machines or tools are Shop Fox?
_____ 0-2 _____ 3-5
____6-9
_____10+
4. Do you think your machine represents a good value?
5. Would you recommend Shop Fox products to a friend?
6. What is your age group?
_____ Yes
_____ Yes
____ No
____ No
_____ 20-29
_____ 50-59
_____ 30-39
_____ 60-69
____ 40-49
____ 70+
7. What is your annual household income?
_____ $20,000-$29,000
_____ $50,000-$59,000
_____ $30,000-$39,000
_____ $60,000-$69,000
____ $40,000-$49,000
____ $70,000+
8. Which of the following magazines do you subscribe to?
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking
____ Practical Homeowner
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Today’s Homeowner
____ Wood
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Model Airplane News
____ Modeltec
____ Woodwork
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Rifle
____ Shop Notes
____ Old House Journal
____ Shotgun News
9. Comments:__________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
WOODSTOCK INTERNATIONAL INC.
P.O. BOX 2309
BELLINGHAM, WA 98227-2309
FOLD ALONG DOTTED LINE
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workman-
ship and materials for a period of two years from the date of original purchase by the original owner.
This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or acci-
dents, lack of maintenance, or reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair or replace, at its expense and at its option, the Shop Fox
machine or machine part which in normal use has proven to be defective, provided that the original
owner returns the product prepaid to a Shop Fox factory service center with proof of their purchase
of the product within two years, and provides Woodstock International, Inc. reasonable opportunity to
verify the alleged defect through inspection. If it is determined there is no defect, or that the defect
resulted from causes not within the scope of Woodstock International Inc.'s warranty, then the original
owner must bear the cost of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are hereby lim-
ited to the duration of this written warranty. We do not warrant that Shop Fox machinery complies
with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under
this warranty exceed the purchase price paid for the product, and any legal actions brought against
Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall
in no event be liable for death, injuries to persons or property or for incidental, contingent, special or
consequential damages arising from the use of our products.
Every effort has been made to ensure that all Shop Fox machinery meets high quality and durability
standards. We reserve the right to change specifications at any time because of our commitment to
continuously improve the quality of our products.
Download from Www.Somanuals.com. All Manuals Search And Download.
High Quality Machines and Tools
Woodstock International, Inc. carries thousands of products designed
to meet the needs of today's woodworkers and metalworkers.
Ask your dealer about these fine products:
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Weslo Home Gym WLAW55072 User Manual
Whirlpool Washer 461970255001 User Manual
Whirlpool Washer Dryer LA6058XS User Manual
White Westinghouse Clothes Dryer WEQ332HS0 User Manual
Yamaha Speaker IF2112 User Manual
Yamaha Stereo Amplifier 001PO 03C0 User Manual
ZALMAN Fan Multi Fan Controller User Manual
Zanussi Freezer ZA18 User Manual
Zanussi Freezer ZUD 9100 F User Manual
Zhone Technologies Network Card Raptor ATM User Manual