2100042
LOADER MOUNTING KIT
for LS72 Loader
®
on Cub Cadet Tractor
SC2400
includes Hose Kit
1029395
Tested. Proven. Unbeatable.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
must be surgically removed as soon as possible by
!
a doctor familiar with this form of injury or gan-
LEA EL INSTRUCTIVO!
grene, serious injury, or death will result. CON-
Si no lee Ingles, pida ayuda a
alguien que si lo lea para que le
traduzca las medidas de seguridad.
TACT A PHYSICIAN IMMEDIATELY IF FLUID
ENTERS SKIN OR EYES. DO NOT DELAY.
„ Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
Safety is a primary concern in the design and
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be wiped
out by an operator’s single careless act.
„ Air in hydraulic systems can cause erratic oper-
ation and allows loads or equipment components
to drop unexpectedly. When connecting equipment
or hoses or performing any hydraulic maintenance,
purge any air in hydraulic system by operating all
hydraulic functions several times. Do this before
putting into service or allowing anyone to
approach the equipment.
In addition to the design and configuration of
equipment, hazard control and accident preven-
tion are dependent upon the awareness, con-
cern, judgement, and proper training of
personnel involved in the operation, transport,
maintenance, and storage of equipment.
„ Protective hose sleeves must cover all hydrau-
lic hoses within 20 inches of the operator and be
secured onto metal hose fittings. Replace hoses or
sleeves if damaged or if protective sleeve cannot
be properly positioned or secured.
It has been said, “The best safety device is an
informed, careful operator.” We ask you to be
that kind of operator.
INSTALLATION
„ Make sure all hydraulic hoses, fittings, and
valves are in good condition and not leaking before
starting power unit or using equipment. Check and
route hoses carefully to prevent damage. Hoses
must not be twisted, bent sharply, kinked, frayed,
pinched, or come into contact with any moving
parts. Operate moveable components through full
operational range to check clearances. Replace
any damaged hoses immediately.
„ This Loader Mounting Kit is to be used only for
the loaders and tractors specified in this manual.
Any other use or modification of this mounting kit
may result in serious injury or death.
„ Hydraulics must be connected as instructed in
this manual. Do not substitute parts, modify, or
connect in any other way.
„ After connecting hoses, check that all control
lever positions function as instructed in the Opera-
tor's Manual. Do not put into service until control
lever and equipment movements are correct.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
„ Do not modify or alter or permit anyone else to
modify or alter the equipment or any of its compo-
nents in any way.
„ Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
„ Use a suitable lifting device of sufficient capac-
ity. Use adequate personnel to handle heavy com-
ponents.
„ Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
„ Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
„ Make sure that all operating and service person-
nel know that if hydraulic fluid penetrates skin, it
Loader Mounting Kit SR3 (4/25/2003)
Safety 3
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADER MOUNT INSTALLATION
CAUTION
■
Only use 2100042 Loader Mounting Kit for
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
mounting Woods LS72 loader on Cub Cadet®
SC2400 tractors. Any other use or modification of
this mounting kit may result in serious injury or
death.
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
NOTICE
■
This equipment must be assembled and
installed on the customer’s tractor by the Woods
dealer. Dealer must thoroughly inspect equipment
and complete each item on the PRE-DELIVERY
CHECK LIST, DELIVERY CHECK LIST, and PROD-
UCT REGISTRATION before equipment is released
to the customer.
Tractor Preparation
NOTICE
■
Clean threaded holes in the tractor chassis thor-
oughly using a tap of the proper size. Paint, rust, or
debris in the threads may not permit cap screws to
be installed and tightened correctly.
For installing this mounting kit, references to right, left,
forward, and rearward directions are determined from
the operator’s position in the tractor seat.
NOTE: Leave all loader mount hardware loose until
mount is completely installed or other wise specified.
1. Shut off engine and set parking brake during instal-
lation.
2. Remove the tractor front weights and weight bracket
if equipped.
As a valued customer, Woods appreciates your comments. Once loader mount and
hydraulic hoses have been installed, please take a few minutes to complete the Loader
Mount Evaluation sheet that was supplied with this mount. Your comments will help us
continue to bring you quality products.
MAN0728 (8/15/2008)
4 Mount Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach Right and Left Mounts
1. Attach right mount (1) to tractor frame using five
cap screws (6) and hardened flat washers (5).
NOTE: If tractor is equipped with an undermount
mower, attach mower lift stop link (3) over the rear
two mounting holes. Secure using two cap
screws (4) and hardened flat washers (5).
1
6
5
2. Repeat steps to install left mount (2).
3. Torque hardware to:
M16 x 2.0P . . . . . . . . . . . . . .125 lbs-ft (169 N-m)
1. 1029390 Right rear mount
2. 1029391 Left rear mount
3. 1029443 Mower lift stop
DP1
4. 307429 M16 x 2.0P x 55 mm HHCS
(used with item 3 only)
Figure 1. Right Mount Installed
5.
6.
57817 5/8 Hardened flat washer
64062 M16 x 2.0P x 40 mm HHCS
Figure 2. Mount INstallation
MAN0728 (8/15/2008)
Mount Installation 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Grill Guard
1. Attach grill guard mounting brackets (B) to the
right and left sides of the tractor frame. Secure to
each side using two cap screws (C), hardened flat
washers (D), and hex nuts (E).
2. Slide grill guard (A) over outside of mounting
brackets and insert lower bar into slots.
3. Secure into position using two (one per side)
clevis pins (F) and klik pins (G).
4. Remove grill guard (A) whenever hood is raised
for maintenance.
5. Torque the cap screws (C) in the tractor frame to
85 lbs-ft (115 N-m).
A.
-------- Grill guard
B. 1029397 Mounting brackets
C.
D.
E.
F.
3379 1/2 NC x 1-1/2 HHCS GR5
57816 1/2 Hardened flat washer
1093 1/2 NC Hex nut
16120 3/8 x 1-1/4 Clevis pin
22411 3/16 x 1 Klik pin
G.
Figure 3. Grill Guard Installation
MAN0728 (8/15/2008)
6 Mount Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
1029395 HOSE KIT
General Description
These instructions are for operating the loader using
the tractor hydraulic remote control lever. To use this
hydraulic connection, the tractor must be equipped
with the manufacturer’s multi-function hydraulic lever
and four tractor hydraulic couplers (Figure 4).
NOTE: Completion of this installation requires con-
nection to the loader.
DP1
Figure 4. Tractor Hydraulic Remote Connection
Assemble Hoses
NOTE: Use thread sealant on all pipe thread connec-
tions and tighten securely to prevent leaks.
1. Attach male quick couplers (2), adapters (3) and
a colored band (4-7) to each loader supply hose
(1).
2. Connect loader supply hoses to loader steel
feedlines on right side of loader as shown in
Figure 6.
1. 1007758 Hose, 46” x 9/16 JICM x 9/16 JICF
2. 316013 Quick Coupler, Male 1/4 NPT
3. 315061 Adapter, 9/16 JICM x 1/4 NPTM
4. 395061 Plastic band, red
Figure 5. Hose Connections
5. 395062 Plastic band, band
6.
7.
56061 Plastic band, green
56062 Plastic band, yellow
Figure 6. Loader Feedline Connection
MAN0728 (8/15/2008)
Installation 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect Hoses
1. Route hydraulic hoses along loader mount and
connect to tractor hydraulic couplers, located
under right side of operator’s platform. See Figure
7.
2
3
2. Be sure to avoid contact with clutch pedal and
other moveable tractor components.
NOTE: Hoses must be routed so that they are not
pinched, bent sharply, or chafed during operation.
Hoses must not interfere with any tractor control
operation or contact any moving parts.
1
4
3. Secure hoses together using plastic hose ties
supplied in hose kit.
Figure 7. Tractor Hydraulic Remote Connection
Figure 8. Remote Couplers and Loader Feedline Connections
8 Installation
MAN07/28 (8/15/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
Verify Control Movements
1. Mount loader to tractor: Remove mount pins
from loader uprights. Align tractor with loader and
slowly drive tractor into loader. Shut off tractor.
2. Connect loader feedline hoses to tractor hydraulic
remote control hydraulics couplers. See Figure 8
for hose connections.
3. Comply with all Safety Rules and start the tractor.
4. Mount loader to tractor by activating bucket
cylinders to raise or lower the loader uprights into
the loader mounts. Slowly advance tractor
forward, activating appropriate cylinders to
engage loader completely into mounts. Insert
mounting pins to secure loader.
●
●
●
●
●
Handle Forward - Boom down
Handle forward to limit - Float position
Handle back - Boom up
Handle to right - Dump bucket or attachment
Handle to left - Rollback bucket or attachment
5. Check that all hydraulic control lever positions
operate the loader movements correctly as
shown in Figure 9.
Figure 9. Single Lever Control Operation
6. If loader movements do not respond correctly,
shut off tractor, relieve pressure, and reconnect
properly. Loader control movements must be
correct before proceeding.
7. Once all loader functions are correct, start the
tractor and operate the loader to check for leaks.
Purge any remaining air from the hydraulic
system and check oil level.
8. When hose routings and correct loader
operations are verified, identify each circuit by
placing a matching colored band around the male
and female quick couplers. The color-coded
bands will make reinstallation easier when the
loader is removed from tractor.
9. Before operating the loader, make sure that
the Pre-Delivery, Delivery, and Pre-Operation
Check Lists in the Loader Operator’s Manual
have been completed.
MAN0728 (8/15/2008)
Installation 9
Download from Www.Somanuals.com. All Manuals Search And Download.
2100042 LOADER MOUNTING KIT
REF PART
QTY
DESCRIPTION
Right mount
REF PART
QTY
DESCRIPTION
1
2
3
4
1029390
1
1
2
4
A
B
C
D
E
F
-------
Grill guard
1029391
1029443
307429
Left mount
1029397
3379 *
57816
2
4
4
4
2
2
Grill guard mounting bracket
1/2 NC x 1-1/2 HHCS GR5
1/2 Hardened flat washer
1/2 NC Hex nut
Mower lift stop link
M16 x 2.0P x 55 mm HHCS
(used with item 3 only)
1093 *
16120
5
6
7
57817 10 5/8 Hardened flat washer
64062 10 M16 x 2.0P x 40 mm HHCS
3/8 x 1-1/4 Clevis pin
3/16 x 1 Klik pin
G
22411 *
1029396
1
Grill guard kit (includes items A - G)
* Standard hardware, obtain locally
HHCS Hex Head Cap Screw
10 Parts
MAN0728 (8/15/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
1029395 HOSE KIT
REF PART
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
1007758
4
4
4
1
1
1
1
4
Hose, 46" x 9/16 JICM x 9/16 JICF
Quick coupler, 1/4
316013
315061
395061
395062
56061
Adapter, 9/19 JICM x 1/4 NPTM
Plastic spiral band, red (NS)
Plastic spiral band, blue (NS)
Plastic spiral band, green (NS)
Plastic spiral band, yellow (NS)
Plastic tie (NS)
56062
88 *
NS Not shown
* Standard hardware, obtain locally
MAN0728 (8/15/2008)
Parts 11
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE Bolt Head
Identification
SAE SERIES
TORQUE
CHART
A
SAE Grade 2
(No Dashes)
SAE Grade 8
(6 Radial Dashes)
SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD
A
SAE 2
SAE 5
SAE 8
Diameter
(Inches)
Wrench
Size
lbs-ft
N-m
8
lbs-ft
10
N-m
13
lbs-ft
14
N-m
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
7/16"
1/2"
6
18
37
12
17
19
26
27
9/16"
5/8"
23
31
35
47
49
67
36
48
55
75
78
106
163
232
325
569
907
1383
3/4"
55
75
85
115
164
230
403
642
979
120
171
240
420
669
1020
13/16"
15/16"
1-1/8"
1-5/16"
1-1/2"
78
106
149
261
416
634
121
170
297
474
722
110
192
306
467
METRIC SERIES
TORQUE
CHART
8.8
Metric Bolt Head
Identification
10.9
A
Metric
Grade 8.8
Metric
Grade 10.9
COARSE THREAD
MARKING ON HEAD
Metric 8.8 Metric 10.9
N-m lbs-ft
FINE THREAD
MARKING ON HEAD
Metric 8.8 Metric 10.9
N-m lbs-ft
A
A
Diameter &
Thread Pitch Wrench
(Millimeters)
Diameter &
Thread Pitch
(Millimeters)
Size
N-m
lbs-ft
6
N-m
lbs-ft
6
6 x 1.0
10 mm
13 mm
16 mm
18 mm
21 mm
24 mm
27 mm
30 mm
34 mm
36 mm
46 mm
8
11
27
8
8
11
29
8
6 x 1.0
8 x 1.0
8 x 1.25
10 x 1.5
12 x 1.75
14 x 2.0
16 x 2.0
18 x 2.5
20 x 2.5
22 x 2.5
24 x 3.0
30 x 3.0
20
15
20
21
16
22
39
29
54
40
41
30
57
42
10 x 1.25
12 x 1.25
14 x 1.5
16 x 1.5
18 x 1.5
20 x 1.5
22 x 1.5
24 x 2.0
30 x 2.0
68
50
94
70
75
55
103
163
250
363
507
684
861
1740
76
109
169
234
330
451
571
1175
80
151
234
323
457
623
790
1626
111
173
239
337
460
583
1199
118
181
263
367
495
623
1258
87
120
184
268
374
505
635
1283
125
172
244
332
421
867
133
194
270
365
459
928
Typical Washer
Installations
Bolt
Flat Washer
Lock Washer
8/9/00
Bolt Torque & Size Charts (Rev. 3/28/2007)
12 Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.
SAE Bolt Thread Sizes
5/16
3/8
1/2
5/8
3/4
7/8
IN
1
2
7
3
4
5
6
MM
25
50
75
100
125
150
175
Metric Bolt Thread Sizes
8MM 10MM
12MM
14MM
16MM
18MM
ABBREVIATIONS
AG .............................................................. Agriculture
MPa.........................................................Mega Pascal
N.......................................................................Newton
NC......................................................National Coarse
NF ...........................................................National Fine
NPSM.....................National Pipe Straight Mechanical
NPT.......................................... National Pipe Tapered
NPT SWF .........National Pipe Tapered Swivel Female
ORBM .......................................... O-Ring Boss - Male
P...........................................................................Pitch
PBY...................................................... Power-Beyond
psi..........................................Pounds per Square Inch
PTO..................................................... Power Take Off
QD....................................................Quick Disconnect
RH..............................................................Right Hand
ROPS........................... Roll-Over Protective Structure
RPM ........................................Revolutions Per Minute
RT ....................................................................... Right
SAE..........................Society of Automotive Engineers
UNC .....................................................Unified Coarse
UNF...........................................................Unified Fine
UNS......................................................Unified Special
ASABE.................... American Society of Agricultural &
Biological Engineers (formerly ASAE)
ASAE ....... American Society of Agricultural Engineers
ATF ............................... Automatic Transmission Fluid
BSPP .............................British Standard Pipe Parallel
BSPTM ................British Standard Pipe Tapered Male
CV.....................................................Constant Velocity
CCW .............................................. Counter-Clockwise
CW............................................................... Clockwise
F ...................................................................... Female
FT .............................................................. Full Thread
GA .................................................................... Gauge
GR (5, etc.) ........................................... Grade (5, etc.)
HHCS ........................................Hex Head Cap Screw
HT........................................................... Heat-Treated
JIC .................Joint Industry Council 37° Degree Flare
LH.................................................................Left Hand
LT........................................................................... Left
m......................................................................... Meter
mm................................................................Millimeter
M.......................................................................... Male
Bolt Torque & Size Charts (Rev. 3/28/2007)
Appendix 13
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
(All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)
Please Enter Information Below and Save for Future Reference.
Date Purchased: ____________________________
Model Number: ____________________________
From (Dealer): ___________________________________________
Serial Number: ___________________________________________
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set
forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE
PRODUCT TO THE ORIGINAL PURCHASER.
Woods backhoe models BH70-X, BH80-X, and BH90-X are warranted for two (2) years from the date of delivery to the original purchaser.
The warranty periods for specific parts or conditions are listed below:
Part or
Condition
Warranted
Duration (from date of delivery
Model Number
to the original purchaser)
BW1260, BW1800
8 years
BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X,
BB7200X, BB8400X, DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3
6 years
Gearbox
components
PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2,
RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2, 5 years
9204RD-2, S15CD, S20CD, S22CD, S25CD, S27CD
3 years (1 year if used in rental or
commercial applications)
RDC54, RD60, RD72
RM550-2, RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2,
9180RD-2, 9204RD-2
Blade spindles
Rust-through
3 years
BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW180-3,
BW1260, BW1800, 2162, 3240, DS1260, DSO1260, DS1440, TS1680
10 years
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been
materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized
service center. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made
with parts other than those obtainable through WOODS.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to
a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS,
in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof
of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS
WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business,
revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute
machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture
replacement parts.
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS,
its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
F-3079 (Rev. 5/15/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
(Replacement Parts For All Models Except Mow’n Machine
Zero-Turn Mowers and Woods Boundary Utility Vehicles)
TM
TM
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and
workmanship for a period of ninety (90) days from the date of delivery of the product to the original
purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a
period of 12 months.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This
Warranty does not cover normal wear or tear, or normal maintenance items.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell
or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser
in any way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with
this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)
days after such defect or noncompliance is discovered or should have been discovered, routed through
the dealer and distributor from whom the purchase was made, transportation charges prepaid.
WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the
product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF
REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF
THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND
WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/
OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising
directly or indirectly from the product, whether such claim is based upon breach of contract, breach
of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality
of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or
goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for
labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to
obtain materials or manufacture replacement parts.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized
to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
F-8494 (Rev. 6/23/2005)
Download from Www.Somanuals.com. All Manuals Search And Download.
PART NO.
MAN0728
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
800-319-6637 tel
800-399-6637 fax
© 2008 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods
Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual
are the property of their respective companies or mark holders. Specifications subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|