OWNER’S MANUAL - OPERATION/INSTALLATION INSTRUCTIONS
®
WINEGARD
RV Digital Satellite System
with RS-1000 Antenna
TM
Model RM-4610, no Digital Magic Elevation Sensor
TM
Model RM-DM61 with “Digital Magic” Elevation Sensor
TM
Model RM-DM55 with “Digital Magic” (No Power Supply)
U.S. PATENT NO. 5,532,710 AND 5,554,998
Made in U.S.A.
Electronic elevation sensor
INSTALL “FRONT” INSCRIBED
ON BASE TOWARD FRONT
OF VEHICLE!
Models RM-4610/DM61
Power supply
Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601
1
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS DO’S AND DON’T’S
DO’S
DON’T’S
1. Do check parking location for obstructions before
raising antenna.
1. Don’t move RV/Coach with the antenna in the UP
position. This will VOID your warranty. This may
also cause damage to your roof.
2. Do carefully raise, lower and rotate the antenna — if
difficult, check for cause.
2. Don’t force the elevating crank up or down. Check for
the cause.
3. Do rotate slowly when searching for the satellite(s)
and check fine tuning on TV set for proper adjustment.
3. Don’t rotate directional handle hard against stops.
4. Do lower antenna before moving vehicle.
4. Don’t apply paint on top of base plate or anywhere
on the lift.
5. Activate programming by calling programming
provider for your receiver.
5. Don’t apply approved sealing compound on gear
housing.
SUGGESTED SETUPS
FOR MULTIPLE TVS
FIGURE 1
FIGURE 2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
NO PICTURE ON TV
1. Do you have a clear line of sight to the satellite? Are
there trees, buildings, etc. in the way? Figure 3 illustrates
the look angle of your reflector.
FIGURE 3
2. Do you have the menu from the receiver? If not, check
the channel the TV set is tuned for — it should be 3 or 4.
Reflector at 90°
3. Check connections at the receiver, TV and antenna.
NO SIGNAL FOUND
1. Have you entered the correct zip code into the re-
ceiver? If the zip code is wrong, you may be searching in
the wrong direction or elevation for the satellite.
24°look angle
LNBF
2. Is your TV working properly? Does it receive pictures
from off-air stations or your VCR?
3. Re-tune system for the best picture, using procedure
on page 2.
4. Inspect antenna. Has it been damaged? If it is even
slightly bent, the receiver may not receive signal.
5. Do you have +12 VDC at the end of the LNBF cable?
Remove cable from LNBF before testing.
6. Contact your dealer or Winegard Technical Services at
800/788-4417.
WARRANTY REPAIR WORK
Before you have warranty repairs on your system, be
sure the company or individual doing the work has been
approved by Winegard Company. If there is not an
approved repair company/individual available, contact
Winegard Company at 800/288-8094 before proceeding.
The Winegard Warranty covers only the mount, antenna
and LNBF. For receiver warranty, refer to the receiver
manufacturer’s warranty.
ANTENNA IS HARD TO ROTATE, OR ANTENNA
DOES NOT ROTATE
1. Inspect antenna on roof. Make sure mount has not
been damaged.
2. Be sure there is no sealant between gear housing and
base plate.
4. Be sure cable is routed correctly. Cable may be
preventing rotation of antenna.
ORDERING REPAIR PARTS
3. Contact your dealer or Winegard Technical Services at
800/788-4417.
Repair parts are available at RV dealers and/or service
centers throughout the U.S. Or you can call Winegard
Company at 800/288-8094. Credit card orders only,
minimum order $5.00.
ANTENNAS HARD TO RAISE, OR ANTENNA DOES
NOT RAISE
1. Inspect antenna on roof. Be sure he mount has not
been damaged.
2. Is the antenna obstructed?
3. Contact your dealer or Winegard Technical Services at
800/788-4417.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND ASSEMBLY
THINGS YOU NEED
Screwdrivers (Phillips and slot)
1-3/4” hole saw
Drill with 1/8” bit
Tape measure
Sealant
(Must be approved for compatibility w/roof)
7/16” wrench
STEP 1. Choose a location on the roof for the unit. The dish must be able to rotate without interfering with other roof-
mounted equipment (air conditioners, etc.), Figure 4. Be sure the interior ceiling plate is easily accessible with no obstruc-
tions that may interfere with operation.
NOTE: Check with your dealer or vehicle manufac-
turer for features that may have been installed for
antenna mounting — reinforced roof areas or pre-wire
installation done at the factory.
FIGURE 4
THE SYSTEM MUST BE LEVEL FOR PROPER OP-
ERATION! Winegard’s RW-5000 roof wedge is available
for sloped roofs, Figure 5. If using roof wedge, installer
will provide longer mounting screws. Mount base plate
and ceiling plate must be parallel with each other,
Figure 5. If shims or wedges are used, the installer must
supply.
STEP 2. Position roof template (inserted in this manual)
on the roof. CAUTION: DO NOT drill through wiring.
Carefully drill a 1-3/4” hole through roof and ceiling of
vehicle. Inspect hole to make sure wiring is intact.
FIGURE 5
Mount base plate and ceiling plate must be parellel with each
other. if shims or wedges are needed, installer must supply.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3. Remove backing from gasket. Attach
adhesive side to base plate. IF YOU ARE USING
THE ROOF WEDGE (RW-5000), use 3/16” gasket
included with the mount UNDER the roof wedge.
Install the 1/16” gasket included with
RW-5000 BETWEEN the mount
FIGURE 6
RS-1000 ANTENNA
and roof wedge.See Figure 7.
The word FRONT is
(4) ANTENNA
MOUNTING BOLTS
embossed on the base. This MUST
FACE the front of the vehicle.
E-CLIPS
Secure to roof using two mounting
screws provided. Check inside the vehicle.
PINS
Be sure the shaft is centered in the hole.
Attach crank handle to shaft.
REFLECTOR
Crank unit up until it stops.
Attach RS-1000 to
ELEVATING TUBES using
E-Clips and Pins supplied.
(4) 1/4 - 20
HEX NUT
STEP 4. Attach reflector to backup assembly, Figure 6.
STEP 5. Attach RS-1000 antenna to elevating tubes.
Use the two E-clips and pins provided, Figure 6. Attach
coax cable to F-jack on antenna and slide on weather
boot, Figure 6.
STEP 6. Install remaining mount base screws. Install the
vent tube on the back of the mount base. (This is the
side opposite the word FRONT.) The hole for the vent
tube is shown in Figure 8.
Cable-entry plate
Minimum 3” from
mount base
FIGURE 7
CAUTION: DO NOT seal hole in vent tube. Put sealant
around the outside of the vent tube, approximately 1/2”
from end, Figure 8. Push the vent tube into the hole. The
sealant will seal the hole as you push in. Leave approxi-
mately 2 to 2-1/2” of the vent tube extending from the
hole. Put a small amount of approved sealant on the roof
and under the vent tube to hold in place.
Cable
clamp
Do not attach
cable clamp
with screw to
base plate
until
installing
cable.
FIGURE 8
Base plate
6-1/8”
Travel Bracket
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7. Facing the front of the dish, find coax cables
attached to side of the feed arm, Figure 9. Measure 24”
of coax from this point and mark. DO NOT CUT. Rotate
mount on base clockwise, fully, until it stops. Route
coax around mount base, Figure 10.
FIGURE 9
Measure coax
24” from plastic tie
wrap on left side of
feed arm. (STEP 7)
Fasten cable clamp in hole in mount base (check roof
template inserted in this manual for correct location) at
end of the coax cable measurement.
FIGURE 10
STEP 8. Feed coax cables through the roof. Weather-
proof cable entry by applying sealant under the lip of the
cable-entry plate and where cable enters roof. Attach
plate to roof with screws provided. Apply sealant over
screws and around edge of roof-through plate, making
sure cable entry is sealed. Secure cables as necessary
to prevent whipping. If cable connections are exposed,
be sure to weatherproof connection!
ANOTHER METHOD OF INSTALLING ROOF CABLE/
ENTRY PLATE: Attach cable to roof using cable clamp.
Use sealant to seal screw heads.
Cable clamp
Cable
Mount travel bracket to roof 6-1/8” from base, Figure
7, page 6.
Cable entry plate
STEP 9. Apply approved sealing compound to screw
heads, cable entrance hole and edge of gasket under
mount, AFTER mounting, Figure 7.
output from the power spply directly to the “TV ANT IN” on
satellite receiver. (Refer to receiver manual.) This allows
you to watch local channels when you turn off the receiver.
STEP 10. Attach satellite coax cable (with RG-6 printed
on it) to the satellite receiver.
STEP 11. Attach RS-1000 coax downlead (with RG-59
printed on it) to RV-7542 power supply. Refer to power
supply instruction sheet. You can connect the antenna
STEP 12. Connect digital elevation sensor at roof level, see
top of page 8.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR RM-DM61/RM-DM55 ONLY
DIGITAL ELEVATION SENSOR ROOF CONNECTIONS
The illustrations below show the different methods of connecting wires at roof level. Method will depend on model. Wire
colors MUST MATCH (i.e. red to reeen to green, black to black, white to white).
Supplied with the DM-2000 only.
This wire harness connects to the digital
elevation sensor on the antenna.
Squeeze pliers until
red plunger is flush
with rest of terminal.
3M UR Terminal
Slide wires all
the way in.
DO NOT strip
wires, terminal
is self strip-
ping.
Snap
connectors
together
NOTE: This terminal is NOT
weatherproof and CANNOT be
left outside on the roof.
Pliers not supplied
NOTE: This terminal is weatherproof and can be left outside
on the roof as LONG AS IT IS SECURED PROPERLY to prevent
whipping in the wind.
FIGURE 11
Roof
Thickness
Directional
Handle Length
(Figure 3E)
Threaded
Rod Length
Worm Gear
Shaft Length
(Figure 3G)
INSIDE YOUR RV
STEP 13. Place the nut on the threaded rod.
STEP 14. Measure and cut the threaded rod with a
hacksaw. Use the chart, Figure 11, to determine the
length.
1-1/2” .............. 2-7/8” ................. 2-3/4” ............... 2-7/8”
1-3/4” .............. 3-1/4” ................. 3” ...................... 3-1/8”
2” ..................... 3-1/2” ................. 3-1/4” ............... 3-1/2”
2-1/4” .............. 3-7/8 ................... 3-1/2” ............... 3-7/8”
2-1/2” .............. 4-1/8” ................. 3-3/4” ............... 4-1/8”
2-3/4” .............. 4-1/2” ................. 4” ...................... 4-1/2”
3” ..................... 4-3/4” ................. 4-1/4” ............... 4-3/4”
3-1/4” .............. 5” ........................ 4-5/8” ............... 4-7/8”
3-1/2” .............. 5-1/4” ................. 4-7/8” ............... 5-1/8”
3-3/4” .............. 5-5/8” ................. 5-1/4” ............... 5-1/2”
4” ..................... 5-3/4” ................. 5-1/2” ............... 5-3/4”
4-1/4” .............. 6-1/8” ................. 5-3/4” ............... 6-1/8”
4-1/2................ 6-1/2 ................... 6” ...................... 6-1/4
4-3/4” .............. 6-5/8” ................. 6-1/8” ............... 6-3/8”
5” ..................... 6-7/8” ................. 6-3/8” ............... 6-5/8”
5-1/4” .............. 7-1/8” ................. 6-5/8” ............... 7”
5-1/2” .............. 7-3/8” ................. 6-7/8” ............... 7-1/4”
5-3/4” .............. 7-5/8” ................. 7-1/4” ............... 7-1/2”
6” ..................... 7-7/8” ................. 7-1/2” ............... 7-3/4”
6-1/4” .............. 8-1/8” ................. 7” ...................... 8”
6-1/2................ 8-1/2 ................... 7-3/4” ............... 8-1/4
6-3/4” .............. 8-3/4” ................. 8” ...................... 8-1/2”
7” ..................... 9” ........................ 8-1/4 ................. 8-7/8”
7-1/4” .............. 9-3/8” ................. 8-5/8” ............... 9-1/8”
7-1/2................ 9-5/8” ................. 8-7/8” ............... 9-3/8”
7-3/4” .............. 9-7/8” ................. 9-1/8” ............... 9-5/8”
8” ..................... 10-1/8” ............... 9-3/8” ............... 10”6-1/4”
8-1/4” .............. 10-3/8” ............... 9-5/8” ............... 10-1/4”
8-1/2................ 10-3/4” ............... 9-7/8” ............... 10-3/8”
8-3/4” .............. 11” ...................... 10”.................... 10-5/8”
9” ..................... 11-1/4” ................ 10-1/4............... 11”
9-1/4” .............. 11-1/2” ................ 10-5/8” ............. 11-1/4”
9-1/2................ 11-3/4” ................ 10-7/8” ............. 11-1/2”
9-3/4” .............. 12” ...................... 11-1/8” .............. 11-3/4”
10”................... 12-3/8” ............... 11-3/8” .............. 12”
10-1/4” ............ 12-5/8” ............... 11-5/8” .............. 12-1/4”
10-1/2” ............ 12-7/8” ............... 11-7/8” .............. 12-1/2”
STEP 15. Remove the nut over the cut end of the
threaded rod. This cleans the threads after cutting.
STEP 16. Thread the cut end of the rod into the hub,
STEP 17. Install the ceiling plate. The rotate/lock
lever must point toward the rear of the vehicle.
Be sure rotate/lock lever is pointing toward back
of vehicle and hole in ceiling aligns with hole in
the ceiling plate.
NOTE: Make sure large and small keyways line up
in the hub and directional handle!
STEP 18. Measure and cut the directional handle;
see Figure 12 and chart, Figure 11. NOTE: A tube
cutter is recommended for cutting the directional
handle. This gives a square cut; a hacksaw does not.
If using an extension, see Step 22, page 9.
Figure 13, page 9, shows what points to measure
between, with and without a roof wedge.
FIGURE 12
HANDLE
LENGTH
DIRECTIONAL
HANDLE
8
Rev. 9/24/04
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 19. The directional handle
and threaded rod will fit roofs up to
5-1/4" thick. If you are using
wedges to compensate for roof/
ceiling slope, be sure to allow for
this extra thickness. You may add
an extension to the directional
handle for thicker roofs. Each
extension will increase the length of
the directional handle by 2-1/4".
WITH ROOF WEDGE
WITHOUT ROOF
WEDGE
Measure from top
of roof wedge to ceiling.
Measure from top
of roof to ceiling.
TOP OF
ROOF WEDGE
TOP OF
ROOF
FIGURE 13
CEILING
CEILING
FIGURE 14
STEP 20. Press the directional handle onto the
hub. Point the arrow on the directional handle
towards the rotate/lock lever to orient to the
splines.
Plastic
Plug
Spacer
Spring
STEP 21. Install the washer and nut on the
threaded rod. Tighten the nut enough to snug the
directional handle to the hub.
STEP 22. IF YOU ARE USING AN EXTEN-
SION, adjust the total length of the directional
handle and extension by cutting the directional
handle. After adjusting parts for proper roof
thickness, glue the extension to the directional
handle. Use ABS (plastic pipe) glue.
Hub
Worm
Gear
NOTE: For roofs thicker that 5-1/4", a longer
aluminum hex shaft will be needed. Contact
Winegard Company for this part.
Threaded
Rod
FIGURE 14A
Ceiling
Plate
CUTTING SHAFT
LENGTH, Figure 14A:
Flip down handle on the
elevating crank handle.
Elevating shaft
Slide elevating crank
handle up shaft until
snug against directional
handle. Mark the
Cut elevating
shaft at inside
surface of
Directional
Handle
crank handle
housing; shaf
goes through
hex-shaped
opening by
screw.
elevating shaft at
inside bottom surface
of crank handle
housing, Figure 12. Cut
shaft at mark, after
removing crank handle.
Reinstall crank.
Crank Handle
STEP 23. Check system for proper operation. Elevate dish with crank handle. A minimum of 14 turns is needed to
elevate dish. Then, move directional handle with dish elevated. Directional handle should turn freely. If possible,
have someone watch to make sure coax does not bind or interfere with dish movement.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: After INITIAL
INSTALLATION, the
FIGURE 15
antenna should ROTATE
APPROXIMATELY 360°
FROM TRAVEL POSITION.
The pointer on the
DIRECTIONAL HANDLE
should point towards the
RED SCREW on the
ROTATION CLAMP when
in TRAVEL POSITION.
ASSEMBLED VIEW
Elevating Shaft
Threaded Tube
3
Directional
Handle Extension
1
Ceiling Plate
Rotation
Clamp
POINTER
MUST POINT
TO RED
Red Screw
2
(4) #10 Phillips Flat
Head Screws
SCREW ON
ROTATION
CLAMP
WHEN IN
TRAVEL
4
Directional
Handle
Flat Washer
ALIGN POINTER
WITH ANTENNA
TRAVEL POSITION
POINT TO
BACK OF RV
POSITION
Nut for
threaded tube
5
ELEVATING
CRANK
HANDLE
(When installed,
extends 2-1/4"
from ceiling).
Snap Handle
into base
CAUTION:
The antenna MUST BE IN THE
TRAVEL POSITION before
ALIGNING the Directional
Handle and Ceiling Plate.
when not in
use.
Tighten screw snugly
10
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED PARTS VIEW
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
INTERIOR
HARDWARE KIT
RK-CEIL
Base
onal Dial
(4) #10 Phillips Flat
Head Screws
Azimuth Lock
Azimuth Lock Knob
Washer
Directional
Handle
Extension
#10 x 3/8"
Red Phillips
Screw
Directional Handle
CRANK HANDLE KIT
RK-HAND
#8-32 x 3/8"
Phillips Screw
Crank Handle Base
#8-32 Square Nut
Crank Handle
Knob
#10 x 3/8" Phillips Screw
Washer
NOT TO SCALE
Rev 6/11/01
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Height when raised........ 30” with satellite antenna in vertical position
Height in travel position........ 8”
Operating radius........ 35” (70” diameter circle)
Roof space required........ 19.5” x 46.75”
LNBF........ Compatible with DISH Network®, DirecTV® and ExpressVu
Color ........ White
Satellite antenna height........ 20.9”
Satellite antenna width........ 19.5”
F/D........ 0.59
Offset angle........ 24°
Satellite antenna gain—
11.2 GHz........ 33.22 dBi
12.1 GHz........ 33.89 dBi
12.6 GHz........ 34.23 dBi
Aperture efficiency........ 73%
Cross polarization (on axis)........ -21 dB
*Beamwidth at -3 dB........ 3.5°
*Beamwidth at -10 dB........ 7.0°
RS-1000 antenna gain —
VHF........ 15.5 dB average
UHF........ 19.5 dB average
RS-1000 antenna height........ 3.25”
RS-1000 antenna width........ 14.5”
Wind Loading........ Up to hurricane force
Weight........ 19 lbs. maximum
Shipping weight........ 21 lbs.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS KITS
HEAD ASSEMBLY RP-RS00
TURRET ASSEMBLY RP-9500
Spring............................................ 1
Head w/bracket and nut ................ 1
Pins .............................................. 2
E-Clip ............................................ 2
Roll Pin ......................................... 1
Gear for worm shaft ...................... 1
Elevation gear ............................... 1
Bushing ......................................... 2
Seal .............................................. 2
O-ring ............................................ 1
Clamp............................................ 2
Shaft ............................................. 1
Bearing, outer ............................... 1
Bearing, inner ................................ 1
Worm gear on shaft....................... 1
Turret top ...................................... 1
Turret base.................................... 1
Turret hub ..................................... 1
Plug .............................................. 1
Plate rotate limit ............................ 1
Screw ............................................ 2
Gasket .......................................... 1
Bracket ......................................... 1
Screw ............................................ 2
Pin ................................................ 2
E-Clip ............................................ 2
Pivot Bracket ................................ 1
REFLECTOR RP-REFL
Dish .............................................. 1
Bolt ............................................... 4
Nut ................................................ 4
BOOM ASSEMBLY RP-BOOM
Top boom ...................................... 1
Bottom boom ................................ 1
Bumper ......................................... 1
Screw ............................................ 1
Bushing ......................................... 1
Lift link .......................................... 2
Pin ................................................ 3
E-Clip ............................................ 4
Nut ................................................ 2
Screw ............................................ 1
Pivot bracket................................. 1
Long bolt ....................................... 1
Nylock nuts ................................... 2
GEAR KIT RP-GEAR
BACKUP & FEED ASSEMBLY RP-BUFA
Fram ............................................. 1
Feed arm ....................................... 1
Roller............................................. 1
Bolt ............................................... 1
Nut ................................................ 3
Bracket ......................................... 1
Pin ................................................ 2
E-Clip ............................................ 3
Screw ............................................ 1
Spring............................................ 1
Clamp............................................ 1
Screw ............................................ 4
Elevation gear (RMs)..................... 1
Elevation gear (RVs & RDs).......... 1
Plug .............................................. 1
O-ring ............................................ 1
Wave washer ................................ 1
Quad ring ...................................... 1
Flat washer ................................... 1
Washer .......................................... 1
Extension...................................... 1
Worm gear, 16” shaft..................... 1
Seal .............................................. 2
Bushing ......................................... 2
RD MODELS
14
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
WINEGARD MOBILE PRODUCTS LIMITED WARRANTY
(2 YEARS PARTS; 1 YEAR LABOR)
Winegard Company warrants this product against defects in materials or workmanship for a period of two (2) years from the date of
original purchase. During year one (1) of such warranty, Winegard Company will also pay authorized labor costs to an authorized
Winegard dealer to repair or replace defective products. No warranty claim will be honored unless at the time the claim is made,
Customer presents proof of purchase to an authorized Winegard dealer (to locate the nearest authorized Winegard dealer, contact
Winegard Company, 3000 Kirkwood Street, Burlington, Iowa 52601, Telephone 319-754-0600 or visit www.winegard.com). Customer
must provide proof of purchase with a dated sales receipt for the Winegard product to verify the product is under warranty. If the date
of purchase cannot be verified, the warranty period shall be considered to begin thirty (30) days after the date of manufacture.
If a defect in material or workmanship is discovered, Customer may take the product to an authorized Winegard dealer for service.
Customer must provide proof of purchase to verify the product is under warranty. If the product is brought to an authorized Winegard
dealer for service prior to expiration of year one (1) of the warranty period and a defect in material or workmanship is verified by
Winegard Technical Services, Winegard Company will cover the Winegard dealer’s labor charges for warranty service. The Winegard
dealer must contact Winegard Technical Services in advance for pre-approval of the service. Approval of the service is at the sole
discretion of Winegard Company.
Alternatively, Customer may ship the product prepaid to Winegard Technical Services (located at 3000 Kirkwood Street, Burlington, Iowa
52601, Telephone 319-754-0600). Customer must return the product along with a brief description of the problem and provide Winegard
Technical Services with Customer’s name, address, and phone number. Customer must also provide proof of purchase to verify the
product is under warranty. If the product is returned before the expiration of the warranty period, Winegard Company will (at its option)
either repair or replace the product.
This Limited Warranty does not apply if the product has been damaged, deteriorates, malfunctions or fails from: improper installation,
misuse, abuse, neglect, accident, tampering, modification of the product as originally manufactured by Winegard in any manner
whatsoever, removing or defacing any serial number, usage not in accordance with product instructions or acts of nature such as
damage caused by wind, lightning, ice or corrosive environments such as salt spray and acid rain.
RETURN AUTHORIZATION POLICY
A Return Material Authorization (RMA) is required prior to returning any product to Winegard Company or Winegard Warranty Services
under this warranty policy. Please call our Technical Services Department at (800) 788-4417 or send an e-mail to [email protected]
to obtain the RMA number. Please furnish the date of purchase when requesting an RMA number. Enclose the product in a prepaid
package and write the RMA number in large, clear letters on the outside of the package. To avoid confusion or misunderstanding, a
shipment(s) without an RMA number(s) or an unauthorized return(s) will be refused and returned to Customer freight collect.
WINEGARD COMPANY DOES NOTASSUMEANY LIABILITIES FORANY OTHER WARRANTIES, EXPRESS OR IMPLIED, MADE BYANY
OTHERPERSON.
ALLOTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FORAPARTICULAR
PURPOSEAND MERCHANTABILITYARE LIMITED TOTHE TWOYEAR PERIOD OF THIS WARRANTY.
In states that do not allow limitations on implied warranties, or the exclusion of limitation of incidental or consequential damages, the
above limitations or exclusions do not apply.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.
This warranty gives Customer specific legal rights. Customer may also have other rights that may vary from state to state.
Rev. 12/21/05
Printed in U.S.A. Winegard Company • 3000 Kirkwood Street • Burlington, Iowa 52601 © Winegard Company, 2003, 2005 2451070 Rev. 12/21/05
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|