MODEL : WS-38 series
OPERATION
MANUAL
Please read and save this guide through before using your range hood.
Store the guide away in a safe place so that you will know where it is,
when you want to refer to it.
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Importaant Safeetty Insturctions
Read and Save These Instructions
CAUTION- To reduce risk of fire and to properly exhaust air, make sure
to properly exhaust air. Be sure to duct air outside- Do not
vent exhaust air into spaces within walls, ceilings, attics,
crawl spaces, or garages.
WARNING- To reduce the risk of fire or electric shock, do not use this fan
with any solid- state speed control device.
WARNING- TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY,
OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer.
B. Before servicing or cleaning the unit, switch power off at service
panel to prevent power from being switched on accidentally.
C. When the service disconnecting means cannot blocked, securely
fasten prominent warning device such as a tag to service panel.
CAUTION- For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapours.
WARNING- TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
A- Never leave surface units unattended at high settings. Boil over
cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
B- Always turn hood on when cooking at high heat or when cooking
flaming foods. (ie, Craepes suzetter, charries jubilee, peppercorn
beef flambe)
C- Clean ventilating fans frequently. Grease should not be allowed
to accumulate on fan or filter.
D- Use proper pan size. Always use cookware appropriate for the
size of the surface element.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING- To reduce the risk of injury in the event of a range top grease
fire, observe the following:
A- SMOTHER FLAMES with a close- fitting lid, cookie sheet,
or metal tray, then turn off the burner. Be careful to prevent
burns. If the flames do not go out immediately, EVACUATE
AND CALL THE FIRE DEPARTMENT.
B- NEVER PICK UP A FLAMING PAN- You may be burned.
C- DO NOT USE WATER including wet dishcloths or towels-
a violent steam explosion will result.
D- USE AN EXTINGUISHER ONLY IF:
1. You know you have a CLASS ABC extinguisher, and you
already know how to operate it.
2. The fire is small and contained in the area where it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
WARNING- Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel burning
equipment to prevent back drafting. Follow the heating equipment
manufacturer's guideline and safety standards such as these
published by the National Fire Protection Association (NFPA),and
the American Society for Heating. Refrigeration and Air
Conditioning Engineers (ASHRAE), and the local code authorities.
Keep the range hood clean.
WARNING- To reduce the risk of fire, use only metal duct work.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Safety Notes
1. All electrical work must be done in accordance with local and/or national
electrical code as applicable for safety. This product must be grounded
if your are unfamiliar with methods of installing electrical wiring, secure
the services of a qualified electrician.
2. Turn off power at service entrance before installing wiring or servicing
this product. (120 volt for range hood. 220 volt for electric range if any)
3. Turn off power to avoid risk of fire, electric shock, or injury for cleaning
or maintenance such as lubrication.
4. Fireplaces, gas furnaces, water heaters, require proper flow of
combustion air and exhaust. Make sure this flow is not altered when
using any exhaust fan.
5. Please read specification label on product for further information and
requirements.
6. Please wear "Safety Gloves" for installation, cleaning, light bulb
changing and dismantling to reduce the risk of any injuries.
CAUTION- To reduce the risk of fire and to properly exhaust air, be
sure to duct air outside. Do not vent exhaust air into spaces
within walls or ceilings or into attics crawl spaces or garages.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Tools and Materials Required
Drill, electric of ratchet driver, with 3/16" wood bit (for drilling starter
holes and 1¼” wood bit (to drill an access holes in the cabinet or
kitchen wall for the electric power line)
One common screwdriver.
Plier (for opening electrical knockout).
Two 1" (thick)x2" (wide)x12" (approximate length) wood strips for
recessed bottom kitchen cabinet installation only. (Purchase locally).
Electrical wire and supplies to comply with local cords.
Four 1¼” long flat head wood screws (purchase locally) to mount
wood strips.
Pencil and ruler for marking locations. Saber saw or keyhole saw for
cutting the 1"x2" wood strips to length.
D. Accessory Package
1. Wood screws 3/16" x 1" L 6pcs.
2. Wire connector with spring 3pcs.
3. Washer 6pcs.
4. 6”/7” Vertical starting round collar 1pc.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Preparing Thee Range Hood
1. Remove the top electrical
knockout, you may plan to
bring power to the range
hood either through the
cabinet or through the wall
(Fig.1)
Electrical Knockout
Fig.1
2. Insert a screwdriver into the knockout slot and bend the knockout
back and forth. (Fig.2)
3. You may have to use pliers to pull the loosened knockout free.(Fig.3)
Fig.3
Fig.2
4. When installed, the bottom edge
of your range hood should be
28" ~ 32" above the top of the
cooking surface. (Fig.4)
Fig.4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
F. Prepariing Thhe Inssttallaattiioonn Locattiioonn
1. If you want to move the electric range to make room for working on the cabinet
turn off the 220 volt power for the electric range at the service entrance.
2. Before moving a gas range, shut off the gas.
NOTE: SKIP FOLLOWING STEPS 3A THROUGH 3D IF THE HOOD IS TO BE
MOUNTED ON A CABINET WITH A FLUSH BOTTOM.
3. For installation onto a recessed bottom cabinet:
a. Measure the space (under the cabinet between the inside front edge and
inside back edge (Fig.5). With a saber saw, cut two 1"x2" wood filler strips
(purchased locally) to fill in the bottom of the cabinet.
b. Start a 1¼ " long wood screw (purchased locally) about 3" from each end
of the 1"x2" wood strips (Fig.6)
c. Position the strips on the cabinet bottom and screw the strips securely to
the cabinet (Fig.7)
d. For a more secure installation, drill four 3/16" holes from inside the cabinet,
down into the wood filler strips. Insert screws into the starter holes in
cabinet and tighten screws until wood filler strips are secured under cabinet.
4. Center the hood in place beneath the cabinet and flush with the front of the
cabinet. Mark the following:
a. The six keyhole mounting slots for the hood. Mark these onto the bottom of
the cabinet; or, if the cabinet bottom is recessed. Onto the wood strips (Fig.7)
b. The electrical knockout hole. (Fig.1)
Fig.6
Fig.5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Screw the four 1" wood screws (for
mounting the hood) into the exact
center of the arrow and into the keyhole
mounting slots marked on the cabinet
bottom (for flush installations), or
marked on the 1”x2” wood strips (for
recessed cabinet installation) (Fig.7)
Do not turn the mounting screws in all
the way. Allow 3/8" of screw to project,
so the hood can be fitted place.
Strips secured
Fig.7
(The screws will be tightened later)
G. Providding Eleectricaal Power
1. After turning off the proper 120 volt circuit at the service entrance,
drill out the electrical power line access hole marked on the cabinet
bottom or wall. Use a 1¼”wood bit. (Fig. 8)
2. Fish the electrical power line through the access hole drilled in the wall or
bottom of the cabinet. Attach an appropriate connector (purchased locally)
to the end of the power line for the type of wiring being installed. Follow all
codes. (Fig.9)
Safety Warning:
If drilling into the walls, be careful not to cut existing electrical cables,
which would create a hazard.
Color:
green/white/black
1
" bit
Connecter
Fig.8
Fig.9
7
Download from Www.Somanuals.com. All Manuals Search And Download.
H. Remove and Reinstall Baffle filters
②
①
1. Wear safety workman gloves and
hold the handles of Baffle filter.
2. Push Baffle filter down ward ①,
then pull a little back ②.
③
4. Pick up the inner oil collector.
3. Lift up the Baffle filter ③.
NOTE : Reinstalling Baffle filters. Reverse the steps as removing Baffle filters.
For mounting under cabinet
1. After above step H, then continue the following steps.
2. Remove 2 screws on the spacer(s).
3. Remove spacer(s).
4. Key hole to mount to under cabinet.
ꢀ
ꢀ
Key hole
8
Download from Www.Somanuals.com. All Manuals Search And Download.
I. Mainttenancee Instrruuction
1. Maintenance shall be important than repair. Please take care of the
needed maintenance in order to secure and extend the excellent
functions and using life.
Note : Before repairing the range hood. Disconnect the power source.
2. After using the machine, wipes the machine by neutral detergent in
order to keep it clean and maintain the appearance with brightness
and sanitation.
3. When the level of dirty oil of the collector reached 4/5 of height, it has to
be removed in order to avoid overflowing and pollution.
J. Ducting
This style of range must be vented via ducting to the outside of the house.
Follow general rules when ducting the hood: Use correct size of ducting
(6" or 7” round ), do not reduce size of ducting, make all turns gradual,
no short corners. If ducting ran will be longer than 10 feet enlarge duct by
at least 1" inch diameter after each 10 feet. Tape all joints in ducting and
all gasketed openings on hood for a tight seal.
For round ducting from the top:
Loosen 2 screws (Ref.1), fit the gray plastic round collar / 6” over the circular
opening on top (Ref.2) and fasten 2 screws (included) in order to provide a tight
seal for ducting to attach to (Ref.3), if you want to use 7” ducting, take 7” converter
(included) to join together with the 6” round collar(Ref.4).
1
2
3
4
ꢀ
ꢀ
ꢀ
Fasten
Loosen
Loosen 2 screws
Fit 6" collar
Fasten 2 screws
Fit 7” converter
9
Download from Www.Somanuals.com. All Manuals Search And Download.
K. Vertical Rectangular Ducting
A. Remove the pre-mounted
6” round duct opening.
D. Overlap the rectangular
starting collar on the top
of transition plate.
Half round section
E. Mounting rectangular starting
collar with remaining screws.
B. Put transition plate by first
installing 4 screws on the
half round section.
(Optional)
F. Completely finished .
NOTE :
An optional kit for vertical
rectangular ducting :
Transition plate
C. Take the rectangular starting
collar. (Optional)
+
Rectangular
starting collar
(Small)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
L. Rear Rectangular Ducting
A. Remove the pre-mounted
6” round duct opening.
D. Pre-mounted
rectangular plate.
B. Put transition plate by first
installing 4 screws on
the half round section.
(Optional)
E. Remove the pre-mounted
rectangular plate.
- to be continued -
C. Use slotted screw driver,
(or whatever flat head)
to knock out the pre-mounted
rear rectangular cap.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
L. Rear Recttaanngguullaarr DDuuccttiinngg
ꢀ
F. Take the pre-mounted
rectangular plate.
G. Mount the rectangular
plate (previous removed)
on top of transition plate.
NOTE :
An optional kit for rear
rectangular ducting :
Transition plate
+
Rectangular
starting collar
H. Insert appropriate rectangular
starting collar (optional)
(Small)
or
(2 different size)
ⓐ 11¼" x 3¾" x 1" (L x W x H)
ⓑ 11¼” x 3¾” x 3⅛" (L x W x H)
(Large)
or
ꢀ
(Small)
I. Mount rectangular
(Large)
J. Rectangular starting collar.
( 11¼” x 3¾” x 3⅛" L x W x H )
(optional)
starting collar.
( 11¼" x 3¾" x 1" )
(optional)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
M. Mounting Range Hood To Cabinet
NOTE : Read “Remove and Reinstall Baffle filter” & “For mounting under cabinet”
on page 8.
1. Position the hood in place so that :
a. The electrical line is routed through the appropriate Knockout
opening. This step will have to be accomplished while positioning
the hood (Fig.10)
b. The large part of the keyhole mounting slots on the hood fit onto
the hood mounting screws projecting from the bottom of the
cabinet. (Fig.11)
2. Adjust the hood so the front is flush with the cabinet front.
3. Tighten the hood mounting screws all the way into the cabinet or into
the 1" x 2" wood strips so the hood is secure.
Color:
green/white/black
Knockout opening
Fig.10
Fig.11
13
Download from Www.Somanuals.com. All Manuals Search And Download.
N. Mountingg Range Hoood Withouutt Cabinett
Bracket
1. Using metal brackets and screws
(included), center hood onto
Screw
board and install screw.
2. Remove the hood from the board and
nail the wood board onto the wall.
(Be sure the nail is in the center of
the stud)
3. Place the range hood on the board
and tighten the screw.
4. Completely finished
14
Download from Www.Somanuals.com. All Manuals Search And Download.
P. Makingg The Electtrical Coonnnection
1. Remove stainless Baffle filters. ( Ref.P8-H)
2. Remove screws on wiring case,
fish out wires through the
knockout. (Fig.12)
wire case
3. Mark the electrical connection by
fastening all wires to the existing
wall wiring according to the their
colors. (Black to Black, White to
White, Green to Ground)
Fig.12
4. After connection is done, reinstall wiring case cover and bottom board.
5. Turn on power and check operation of fan and light.
6. After completely installation, reinstall the stainless Baffle filter and oil collector.
( Ref. P8-H)
Q. Use and CCaarree
Night light sensor
OFF
Main power
3 speed fan selection
LED light
Fan OFF
1.
Main power button
NOTE: ALL FUNCTIONS CAN BE WORKED ONLY UNDER THE
MAIN POWER IS ON.
A. By pressing
B. By pressing
, all functions are stand-by.
again, all functions will be turned off.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Use for Fan
: Fan speed selection and fan off.
OFF
A. Fan ON: When the
main power button is being pressed, by pressing
button
/
/
for desired fan speed.
- slow speed
- medium speed
- high speed
B. Fan OFF: To turn off the fan, just press the
button, or press off
OFF
the
main power button.
NOTE: a. The fan speed can be interchanged by pressing any one of above
3 buttons, however.
b. NEVER PRESS ANY OF TWO BUTTONS IN A TIME.
3. Use for Light
NOTE: MAKE SURE THE
TURNING ON THE LED LIGHT.
to turn on the LED light.
again tor turn off the LED light.
MAIN POWER BUTTON IS PRESSED BEFORE
A. Press
B. Press
4. Use for Auto-sensor LED night light
NOTE: MAKE SURE THE MAIN POWER BUTTON IS PRESSED BEFORE
TURNING ON THE LED LIGHT.
A. The auto-sensor of LED night light will be automatically turn on at 20%
brightness compare to original when the surroundings is getting darker
(or dark).
B. When the surroundings is getting brighter (or bright), the auto-sensor
will turn the night light off automatically.
C. To turn off the auto-sensor night light button, after cooking turns off the
main power button. To keep this function, remain the
button always ON.
main power
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Note:
Range hood should be turn on either before or the same time when cooking
begins. After cooking, range hood should be kept on for about 3 more minutes
for complete ventilation of cooking odor.
Care Instruction :
Please always pull the plug out before cleaning or dismantling, wear
"Safety gloves " to reduce the risk of any injuries.
Exterior : Can be cleaned with any type of non-abrasive detergent and a
clean cloth. "Green Pad" or any metal type cleaning pad is
not recommended for exterior. As those may scratch the
graphic wordings on control panel.
Interior : 1. Switch ON the fan at High, mix mild detergent with water in
mist-sprayer, at fine-spray mixture on to the blades for 60 seconds
with the fan running. ( mist sprayer is not included)
2. Leave fan on for an additional 3 minutes to dry oil basin.
3. Repeat on other turbine vane (can be cleaned simultaneously
with the first).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
R. Troubleshhootings
Symptom
Correction
A. Check power source to see if it is normal.
Fan are not operatable.
B. Check power inlet plug to see if it is
plugged firmly into it's socket.
A. Disconnect the power source.
Illuminating LED light
does not work
B. Check LED light, replace it with a new
one if it is burned out.
A. Check for damaged vanes.
Hood vibrates.
B. Check if exhaust duct is secured.
S. Replace The LLEEDD LLiigghhtt
Before changing LED light ensure the unit is pressed the main power button off,
when you want to change the LED light please always wear working gloves.
1. Using suitable tool (small slotted screw driver) gently pry off the LED light set.
2. Taking off the wire connecter with LED light set.
3. Replace a new LED light set and reconnect the wire to the connector.
4. Before push back the original LED light position, test the LED light.
LED driver:
Model: HP1500-36
input: 100~240vdc
LED light: 1W
output: 3.6vdc=1500maH
Model: HP-15A
NOTE: For LED light replacement, you may not find the appropriate LED lights
from market, please contact with distributor(s)/dealer(s).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
T. Parts Layout Diagram
1
20
19
18
4
5
17
16
15
3
2
6
14
7
8
9
10
11
12
13
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
No.
Description
Hood casing
Air chamber
Parts no.
Per hood
38-0130(30”) / 38-0136(36”)
38-0142(42”) / 38-0148(48”)
1
2
1
1
1
1
2
1
2
2
2
2
2
4
2
2
1
1
1
1
2
1
38-02
38-0330(30”) / 38-0336(36”)
38-0342(42”) / 38-0348(48”)
3
Top plate
4
6” round vent (Vertical ventilation)
Motor housing
Inner vent (Rear ventilation)
Motor (s)
38-04
38-05
38-06
38-07
38-08
38-09
5
6
7
8
Fan (s)
9
Oil tunnel
38-1030(30”) / 38-1036(36”)
38-1042(42”) / 38-1048(48”)
10
11
12
13
14
15
16
17
18
19
20
* Spacer (s)
* Baffle filter (s)
* Handle (s)
38-11
38-12
38-13
38-14
Oil collector
* LED light
38-1530(30”) / 38-1536(36”)
38-1542(42”) / 38-1548(48”)
LED light fixture
Control panel
Control button
LED driver
38-16
38-17
38-19
38-20
Bracket
38-2130(30”) / 38-2136(36”)
38-2142(42”) / 38-2148(48”)
Wiring partition
■ With * (asterisk) on 42” / 48” quantity may be varied.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
U. Circuitt Diagram
NOTE : Any faults with this unit should only be attended to by a qualified technician.
NIGHT LIGHT
H I
OFF
POWER
CORD
W
Y
W
Y
J K
LED
LED
K
J
I
H
AC/DC
POWER SUPPLY UNIT
MOTOR
MOTOR
Voltage : 110V/60Hz
Power consumption : maxi 170W
(Motor + LED light)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
V. Sizzee
2°
15”
11”
12”
5”
26°
2-1/2”
92°
22-7/16”
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
Windster Hoods Inc. warrants this product against defects in material or
workmanship as follows:
1) Labor: For a period of one (1) year from the date of purchase, if this product
is determined to be defective, Windster will repair or replace the product, at its
option, at no charge. After the warranty period, you must pay for all labor
charges. During the “labor” warranty period there will be no charge for labor.
2) Parts: In addition, Windster will supply, at no charge, new or rebuilt
replacements in exchange for defective parts for a period of two (2) years.
After the warranty period, you must pay for all parts costs. During the “parts”
warranty period, there will be no charge for parts
You must carry-in or mail-in your product during the warranty period. This warranty
only applies to products purchased and serviced in the United States or Canada.
What Is Not Covered By These Warranties:
1) Conditions and damages resulting from any of the following:
? Improper installation, delivery, or maintenance.
? Any repair, modification, alteration or adjustment not authorized by the
manufacturer or an authorized service dealers.
? Misuse, abuse, accidents, or unreasonable use.
? Incorrect electric current, voltage or supply.
? Improper setting of any control.
? Improper chemical cleaning.
2) Light Bulbs
3) Products purchased for commercial or industrial use (such as in a hotel, office,
restaurant, or other business)
4) Damage due to earthquake, flood, storm, etc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Defective Products:
All products will be inspected, tested, and carefully packed by the manufacturer
before shipping to customers. Products that are damaged during transit can only be
exchanged for the same product, under the condition that the customer must get a
RMA (Return Merchandise Authorization) from Windster. When products are
received defective, you must notify us within the 3 business days of receiving the
package. Replacement products are only shipped when the RMA is issued. NO
EXCEPTIONS.
Return Policy
Windster offers only the best and highest quality products. If you are not satisfied
with your purchase, please contact us within 3 business days of product arrival to
obtain a Return Merchandise Authorization (RMA). Returns sent without a RMA will
not be accepted. There will be a 25% re-stocking fee for every returned items.
Shipping fee will also be deducted from the original purchase price. When returning a
package, please include a copy of your purchase receipt. Use the original shipping
box and packing materials and completely remove or cover the original shipping label.
Make sure that products are in brand new condition, uninstalled, un-drilled, and
contain everything that came with the package as when you first received it. If any
parts or manuals are missing, we have the right not to accept the return.
We suggest that you use a traceable and reputable carrier of your choice to ship your
return. Your credit or refund will be processed within 10-14 business days from the
date we receive your return.
2102 N. Seaman Ave., S. El Monte, CA 91733 TEL:626-350-1015 626-350-5215 FAX:626-350-1254
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
WINDSTER
w w w . w i n d s t e r h o o d . c o m
2102 N. Seaman Ave.,
S. El Monte, CA 91733
TEL:(626)350-1015
(626)350-5215
FAX:(626)350-1254
© 2006-2008 Windster Hoods, Inc.
Specifications subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|