Windsor Vacuum Cleaner 10061090 User Manual
iScrub  
Operating Instructions (ENG)  
CSX24  
MODELS:  
10061090  
CSX26SP  
10061160  
Read these instructions before using the machine  
86317500-A  
11/15/08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
GROUP PARTS LIST  
Machine Data Log/Overview................................2  
Table Of Contents ................................................3  
Bumper ..............................................................5-1  
Control Panel.....................................................5-3  
Control Panel Housing.......................................5-5  
Decal..................................................................5-7  
Frame-Lower .....................................................5-9  
Frame-Upper .....................................................5-11  
Pedal Platform...................................................5-13  
Rear Cover ........................................................5-17  
Scrub Brush/Pad Driver-Disk.............................5-19  
Scrub Brush/Pad-Cylindrical..............................5-21  
Scrub Deck - Disk..............................................5-23  
HOW TO USE THIS MANUAL  
How To Use This Manual.....................................1-1  
SAFETY  
Important Safety Instructions ............................ 2-1  
Hazard Intensity Level....................................... 2-2  
Safety Label Location........................................ 2-3  
al ...................................5-25  
Scrub Deck – Cylindric  
OPERATIONS  
Scrub Deck Mounting-Cylindrical ......................5-27  
Scrub Deck Lift-Disk..........................................5-29  
Scrub Deck Actuator-Cylindrical........................5-31  
Scrub Deck Skirts-Disk......................................5-33  
Scrub Deck Aqua-Mizer™.................................5-35  
Solution-Disk......................................................5-37  
Solution-Cylindrical............................................5-39  
Squeegee - Disk................................................5-41  
Squeegee – Cylindrical......................................5-43  
Squeegee Lift-Disk ............................................5-45  
Squeegee Lift-Cylindrical...................................5-47  
Squeegee Swing ...............................................5-49  
Steering .............................................................5-51  
Tank...................................................................5-53  
Vacuum..............................................................5-55  
Wheel-Front Drive .............................................5-57  
Wheel-Rear........................................................5-59  
Wiring-Batteries.................................................5-60  
Wiring-Components...........................................5-63  
Wiring-Control Panel .........................................5-65  
Wiring-Disk ........................................................5-67  
Wiring-Cylindrical...............................................5-70  
Wiring-Drive Motor.............................................5-73  
Wiring-Main Harness.........................................5-75  
Wiring-Pedal Platform........................................5-77  
Hose Diagram-Disk ...........................................5-79  
Hose Diagram-Cylindrical..................................5-80  
Suggested Spare Parts .....................................5-81  
Technical Specifications.................................... 3-1  
How The Machine Works.................................. 3-3  
Components...................................................... 3-4  
Drive Controls.................................................... 3-5  
Scrub Controls................................................... 3-9  
Scrub Controls-Squeegee................................. 3-11  
Machine Operation............................................ 3-13  
Pre-Run Machine Inspection........................ 3-13  
Starting Machine .......................................... 3-13  
Emergency Stop Procedures ....................... 3-13  
Filling Solution Tank..................................... 3-14  
Normal Scrubbing......................................... 3-14  
To Begin Scrubbing...................................... 3-15  
Priming Pump............................................... 3-15  
To Stop Scrubbing........................................ 3-16  
Double Scrub................................................ 3-16  
Emptying And Cleaning Tanks..................... 3-17  
MAINTENANCE  
Service Schedule .............................................. 4-1  
Batteries. ...........................................................4-2  
Squeegee.......................................................... 4-6  
Scrub Brushes................................................... 4-9  
Scrub Deck-Disk................................................ 4-10  
Circuit Protection............................................... 4-13  
Solution Strainer & Pump.................................. 4-14  
Vacuum & Float Shut-Off .................................. 4-17  
Drive Motor & Brake.......................................... 4-19  
Bag Replacement.............................................. 4-22  
Transporting Machine........................................ 4-23  
Machine Troubleshooting.................................. 4-24  
OPTIONS  
Battery Cart – Option.........................................6-1  
Seat – Option.....................................................6-5  
Warning Light – Option......................................6-7  
Serial Numbers..................................................6-9  
Warranty  
86317500 CHARIOT SCRUBBER 11/15/08  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW TO USE THIS MANUAL  
This manual contains the following sections:  
The SAFETY section contains important information  
regarding hazard or unsafe practices of the  
machine. Levels of hazards are identified that could  
result in product or personal injury, or severe injury  
resulting in death.  
-
-
-
-
-
HOW TO USE THIS MANUAL  
SAFETY  
OPERATIONS  
MAINTENANCE  
PARTS LIST  
The OPERATIONS section is to familiarize the  
operator with the operation and function of the  
machine.  
The HOW TO USE THIS MANUAL section will tell  
you how to find important information for ordering  
correct repair parts.  
The MAINTENANCE section contains preventive  
maintenance to keep the machine and its  
components in good working condition. They are  
listed in this general order:  
Parts may be ordered from authorized Windsor  
dealers. When placing an order for parts, the  
machine model and machine serial number are  
important. Refer to the MACHINE DATA box which  
is filled out during the installation of your machine.  
The MACHINE DATA box is located on the inside of  
the front cover of this manual.  
-
-
-
-
-
Batteries  
Scrub Brushes  
Adjusting Squeegee  
Service Schedule  
Machine Troubleshooting  
The PARTS LIST section contains assembled parts  
illustrations and corresponding parts list. The parts  
lists include a number of columns of information:  
-
-
REF – column refers to the reference  
number on the parts illustration.  
PART NO. – column lists the part  
number for the part.  
The model and serial number of your machine are  
located below the battery compartment of the  
machine.  
-
-
PRV NO. - Reference No.  
QTY – column lists the quantity of the  
part used in that area of the machine.  
DESCRIPTION – column is a brief  
description of the part.  
-
-
SERIAL NO. FROM – If this column has  
an (*) and a Reference number, see the  
SERIAL NUMBERS page in the back of  
your manual. If column has two asterisk  
(**), call manufacturer for serial number.  
The serial number indicates the first  
machine the part number is applicable  
to. The main illustration shows the most  
current design of the machine. When a  
boxed illustration is shown, it displays  
esign.  
the older d  
-
NOTES – column for information not  
noted by the other columns.  
NOTE: If a service or option kit is installed on your  
machine, be sure to keep the KIT INSTRUCTIONS  
which came with the kit. It contains replacement  
parts numbers needed for ordering future parts.  
NOTE: The number on the lower left corner of the  
front cover is the part number for this manual.  
86317500 CHARIOT SCRUBBER 11/15/08  
1-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFETY INSTRUCTIONS  
When using an battery powered appliance, basic precaution  
must always be followed, including the following:  
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.  
To reduce the risk of fire, electric shock, or injury:  
Use only indoors. Do not use outdoors or expose to rain.  
Use only as described in this manual. Use only manufacturer’s recommended components and attachments.  
If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return  
it to an authorized service center.  
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.  
This machine is not suitable for picking up hazardous dust.  
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near  
flammable fluids, dust or vapors.  
This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops  
and offices for more than normal housekeeping purposes.  
Maintenance and repairs must be done by qualified personnel.  
If foam or liquid comes out of machine, switch off immediately.  
Disconnect battery before cleaning or servicing.  
Before the machine is discarded, the batteries must be removed and properly disposed of.  
Make sure all warning and caution labels are legible and properly attached to the machine.  
During operation, attention shall be paid to other persons, especially children.  
Before use all covers and doors shall be put in the positions specified in the instructions.  
When leaving unattended, secure against unintentional movement.  
The machine shall only be operated by instructed and authorized persons.  
When leaving unattended, switch off or lock the main power switch to prevent unauthorized use.  
Only chemicals recommended by the manufacturer shall be used.  
This appliance has been designed for use with the brushes specified by the manufacturer. The fitting of other  
brushes may affect its safety.  
Do not use on surfaces having a gradient of over 10% (6 degrees).  
SAVE THESE INSTRUCTIONS  
86317500 CHARIOT SCRUBBER 11/15/08  
2-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HAZARD INTENSITY LEVEL  
The following symbols are used throughout this guide as indicated in their descriptions:  
HAZARD INTENSITY LEVEL  
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR  
SAFETY. The level of hazard intensity is determined by the following definitions:  
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.  
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property  
damage.  
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.  
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating  
condition. Following is information that signals some potentially dangerous conditions to the operator or the  
equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on  
the machine. Please take the necessary steps to train the machine operating personnel.  
FOR SAFETY:  
DO NOT OPERATE MACHINE:  
Unless Trained and Authorized.  
Unless Operation Guide is Read and understood.  
In Flammable or Explosive areas.  
In areas with possible falling objects.  
WHEN SERVICING MACHINE:  
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use  
Windsor approved replacement parts.  
Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep  
solution tank in raised position when charging. Keep sparks and flames away from the batteries. Do not  
smoke around batteries.  
Disconnect batteries before working on machine. Only qualified personnel should work inside machine.  
Always wear eye protection and protective clothing when working on or near batteries. Avoid skin contact  
with the acid contained in the batteries.  
Never allow metal to lie across battery tops.  
86317500 CHARIOT SCRUBBER 11/15/08  
2-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY LABEL LOCATION  
NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become  
illegible, promptly replace them.  
86244300  
PRV NO. 500955  
WARNING LABEL  
86252520  
PRV NO. 80885  
BATTERY  
CAUTION  
2-3  
86317500 CHARIOT SCRUBBER 11/15/08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TECHNICAL SPECIFICATIONS  
ITEM  
Nominal power  
DIMENSION/CAPACITY  
1800 W  
Rated Voltage  
Rated Amperage  
Batteries  
36 Volts DC  
50 amps  
3 X12 Volt 195-215 AH @ 20 hr. rate  
21 in. x 16 in. x 17 in. tall  
(533mm x 406mm x 432mm)  
2 x .3 HP (190 W)  
Battery Compartment Dimensions  
Scrub Brush Motors - Disk Machine  
Scrub Brush Motors - Cylindrical Machine  
Vacuum Motor(s)  
2 x .75 HP (560 W)  
.63 HP (470 W)  
Maximum flow rate of vacuum motor  
Maximum suction of vacuum motor  
Propelling Motor  
72 cfm (33.98 liters per second)  
47.3 inches of water (11.7 kPa)  
.75 HP (560 W)  
Mass (GVW)  
1245 lbs (565 kg)  
Weight empty without batteries  
558 lbs (253 kg)  
1.3 GPM pump, fully variable with automatic shut-off  
in neutral  
Solution Control  
Solution capacity  
25 gal (95 L)  
Recovery capacity  
25 gal (95 L)  
Scrub brush diameter - Disk Machine  
Scrub brush diameter - Cylindrical Machine  
Scrub brush pressure  
12 inch (305 mm)  
4.1 inch (105 mm)  
0-150lbs (0-667N)  
Scrub brush speed - Disk Machine  
Scrub brush speed - Cylindrical Machine  
Tires  
300 rpm  
500 rpm-slow, 800 rpm-medium, 1300rpm-fast  
10 in. (254mm) Solid Scrubber Compound  
104 psi (715 Kpa)  
Foundation Pressure  
Maximum Speed  
Theoretical Coverage  
Frame Construction  
3.5 miles/hour (5.6 Km/hour)  
24,200 ft²/hr @ 2.5 mph with 2 in. overlap  
Powder coated steel  
Electrical parking brake, sets automatically whenever  
operator steps off platform or engages emergency  
stop.  
Brake  
Minimum aisle u-turn width  
56 in. (1425 mm)  
Maximum rated climb and descent angle  
7.5 degrees  
3-1  
86317500 CHARIOT SCRUBBER 11/15/08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TECHNICAL SPECIFICATIONS  
ITEM  
MEASURE  
Height  
Length  
50.6 inches (1285 mm)  
52.5 inches (1330 mm)  
26.5 inches (670 mm)  
32.7 inches (830 mm)  
37 inches (970 mm)  
24 inches (610 mm)  
26 inches (650 mm)  
Width without squeegee  
Width of squeegee - Disk Machine  
Width of squeegee - Cylindrical Machine  
Width of scrub path - Disk Machine  
Width of scrub path - Cylindrical Machine  
LENGTH  
WIDTH  
HEIGHT  
SPECIAL NOTES:  
This appliance is not intended for use by persons  
(including children) with reduced physical, sensory or  
mental capabilities, or lack of experience and  
knowledge, unless they have been given supervision  
or instruction concerning use of the appliance by a  
person responsible for their safety. Children should be  
supervised to ensure that they do not play with the  
appliance.  
The sound pressure level at the operator’s ear was  
measured to be 68 dBA (Disk), 76dBA (cylindrical).  
This was a nearfield, broad-band measurement taken  
in a typical industrial environment on a tile floor. This  
appliance contains no possible source of impact noise.  
The instantaneous sound pressure level is below  
63 Pa.  
The weighted root mean square acceleration at the  
operator’s arms was measured to be below 2.5m/s2 .  
This was a tri-axial, third-octave-band measurement  
made during normal operation on a composite tile floor.  
The measurement and related calculations were made  
in accordance with ANSI S3.34-1986.  
86317500 CHARIOT SCRUBBER 11/15/08  
3-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOW THIS MACHINE WORKS  
The Chariot® is a battery powered, self-propelled,  
hard floor scrubber intended for commercial use.  
The appliance applies a cleaning solution onto a  
hard floor, scrubs the floor with brushes, and then  
vacuums the soiled water back into the recovery  
tank.  
The scrub deck side squeegees control the cleaning  
solution on the floor so that the squeegee can pick it  
up.  
The function of the recovery system is to vacuum  
the soiled water back into the recovery tank. The  
recovery system consists of the squeegee, vacuum  
motor, float ball filter, recovery bag. The squeegee  
wipes the dirty solution off the floor as the machine  
moves forward. The vacuum motor provides suction  
to draw the dirty solution off the floor and into the  
recovery bag. The float ball filter protects the  
vacuum fan from debris and foam. The recovery  
bag stores the dirty solution.  
The machine's primary systems are the solution  
system, scrub system, recovery system, and  
operator control system.  
The function of the solution system is to store  
cleaning solution and deliver it to the scrub system.  
The solution system consists of the solution tank,  
strainer, pump, valve. The solution tank stores  
cleaning solution (water and detergent) until it is  
delivered to the scrub system. The strainer protects  
the pump from debris. The valve automatically  
prevents solution flow unless the scrub brushes are  
turned on and the machine is being propelled.  
The function of the operator control system is to  
control the direction and speed of the machine. The  
directional control system consists of the direction  
control drive reset switch, throttle pedal, emergency  
stop/brake switch, steering wheel, propel controller,  
and drive wheel. The directional control drive reset  
switch signals forward or reverse direction and  
makes sure the operator is on platform before  
machine will propel. The controller interprets signals  
from the throttle pedal to command the drive wheel  
to propel or slow the machine. The steering wheel  
points the drive wheel in the direction desired by the  
operator. The parking brake automatically engages  
when the operator steps off the platform. The  
emergency stop/brake can be used to hold the  
machine on slopes.  
The function of the scrub system is to scrub the  
floor. The disk scrub system consists of two rotary  
type disk scrub brushes, motors, scrub deck skirt  
and lift actuator. The brushes scrub the floor as the  
motors drive the brushes. The brush drive hubs  
allow the scrub brushes to follow irregularities and  
changes in the floor without loosing contact with the  
floor. The scrub deck skirts control the cleaning  
solution on the floor so that the squeegee can pick it  
up.  
The scrub plus system consists of two cylindrical  
type brushes, motors, scrub deck side squeegees,  
hopper, lift actuator. The cylindrical scrub head is  
designed to eliminate debris that may be caught in  
the squeegee while scrubbing. Water is applied to  
the first scrubbing brush turning in a clockwise  
rotation when viewed from the right side of machine.  
The first brush scrubs dirt and debris between the  
brushes. The second scrubbing brush, turning in a  
counter clockwise rotation, picks up debris and  
throws it into a removable hopper. Water is allowed  
to drain out the hopper into the squeegee path  
where it is recovered from the floor.  
86317500 CHARIOT SCRUBBER 11/15/08  
3-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPONENTS  
7
2
1
11  
3
5
6
8
12  
10  
4
9
7. Recovery Dome  
8. Recovery Drain Hose  
9. Scrub Deck Aqua-Mizer™  
10. Scrub Deck Skirts/Side Squeegees  
11. Solution Cover  
1. Control Panel-Drive  
2. Control Panel-Scrub  
3. Control Housing  
4. Pedal Platform  
5. Rear Cover  
12. Solution Drain Hose  
6. Tank  
86317500 CHARIOT SCUBBER 11/15/08  
3-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DRIVE CONTROLS  
7
8
9
5
2
3
1
6
4
86317500 CHARIOT SCRUBBER 11/15/08  
3-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DRIVE CONTROLS  
1.  
2.  
3.  
4.  
5.  
Key Switch  
6.  
7.  
8.  
9.  
Steering Wheel  
Speed Control  
Battery Discharge Indicator  
Hour Meter  
Emergency Stop/Brake Switch  
Directional Control / Drive Reset Switch  
Throttle Pedal  
Horn Button  
1.  
KEY SWITCH  
Controls the power for machine functions.  
To turn the machine power on, rotate key clockwise.  
To turn the machine off, rotate key counterclockwise.  
When the key is turned on the battery symbol will flash while the system runs self-diagnostics and returns  
scrub deck and squeegee to their raised positions, if necessary. The controller will not respond to other  
commands until this routine is complete.  
2.  
EMERGENCY STOP/BRAKE SWITCH  
This safety feature is designed to cut all power to the machine at any time and apply parking brake.  
To shut the machine power off, push the Emergency Stop Switch, this will also engage the parking brake and  
cause the machine to stop immediately.  
To reset the machine, rotate the switch clockwise.  
3.  
DIRECTIONAL CONTROL / DRIVE RESET SWITCH  
This safety feature is designed to ensure safe engagement of propel drive. Each time the machine power is  
turned on, or each time an operator steps on to the platform, the Drive Reset Switch must be pushed before  
machine will propel.  
Controls the direction of travel of the vehicle. The lit arrow on the switch indicates direction of travel.  
To travel forward, press the top of the switch.  
To travel in reverse, press the bottom of the switch.  
THROTTLE PEDAL  
4.  
Controls the speed of the vehicle within the speed control setting selected. Pressing the pedal causes the  
machine to travel in the direction selected by the Directional Control Switch.  
To increase speed, increase pressure on the pedal.  
To decrease speed, decrease pressure on the pedal.  
86317500 CHARIOT SCRUBBER 11/15/08  
3-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DRIVE CONTROLS  
5.  
6.  
7.  
HORN BUTTON  
The horn is activated by pressing the horn button.  
STEERING WHEEL  
The steering wheel turns the front wheel causing the machine to change direction.  
SPEED CONTROL  
Controls the maximum speed of the machine. There are two transport settings, slow and fast.  
To change speed, rotate the dial to either slow or fast position. The slow position is to the left  
(counterclockwise), fast to the right (top position).  
The throttle pedal will always regulate the speed between 0 and maximum.  
SLOW  
FAST  
86317500 CHARIOT SCRUBBER 11/15/08  
3-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DRIVE CONTROLS  
8. BATTERY CHARGE LEVEL INDICATOR  
Indicates the charge level of the batteries.  
The meter display is divided into 10 vertical bars. Bars illuminated on the far right indicate full charge. Bars  
flashing near the left side indicate the batteries should be recharged. Further operation of the machine  
could damage the machine or the batteries.  
When the machine is left overnight with less than a full charge, the display may initially indicate a full  
charge. It will also indicate a full charge if the batteries are disconnected, then reconnected. After a few  
minutes of operation the meter will give the correct charge level.  
9. HOUR METER  
Records the number of hours the machine has been in scrubbing operation. This information is useful in  
determining when to service the machine.  
86317500 CHARIOT SCRUBBER 11/15/08  
3-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB CONTROLS  
A1  
1
A2  
A3  
C
B
1. FUNCTION MODE SWITCH  
The first two positions are for transport only. See drive controls section.  
A1 – Daytime cleaning/light cleaning  
This mode is used for light cleaning. In this mode the machine will propel at a maximum of medium  
speed. The scrub deck will automatically lower to a lower down pressure setting. The water will flow at a  
low rate. Water will automatically shut off in neutral and restart when pressure resumes. The squeegee  
will automatically lower and vacuum will continue on at a low flow. (Squeegee will continue to lower and  
the vacuum will continue to run in neutral. The squeegee will raise in reverse.)  
A2 – Medium scrub level cleaning  
This mode is used for medium level cleaning. In this mode the machine will propel at a maximum of  
medium speed. The scrub deck will lower to a medium down pressure. The water will flow at a medium  
rate. The vacuum will flow at a medium rate.  
86317500 CHARIOT SCRUBBER 11/15/08  
3-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB CONTROLS  
A3 – Heavy scrub level cleaning  
This mode is used for heavy level cleaning. In this mode the machine will propel at a maximum of slow  
speed. The scrub deck will lower to a heavy down pressure. The water will flow at a high rate. The  
vacuum will flow at a high rate.  
B – Vacuum only mode  
This mode is used for picking up solution only. The brushes and water will both be up and off. In this  
mode the machine will propel at a maximum of medium speed. The squeegee will automatically lower  
and the vacuum will come on. The vacuum will flow at a high rate. The squeegee will raise during  
reverse propelling. The squeegee and vacuum will remain down and on in neutral propel.  
C – Double Scrub cleaning  
This mode is used for putting down solution and scrubbing without picking it back up. In this mode the  
machine will propel at a maximum speed of slow. The scrub deck will automatically lower to a heavy  
scrub level. The solution will flow at a high rate. The brushes and water will shut off and raise when  
the machine is in neutral. They will resume when propelling is resumed.  
86317500 CHARIOT SCRUBBER 11/15/08  
3-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB CONTROLS-SQUEEGEE  
1
2
1. Squeegee Deflection Adjustment Knobs  
2. Squeegee Pitch Adjustment Rod  
86317500 CHARIOT SCRUBBER 11/15/08  
3-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB CONTROLS-SQUEEGEE  
1. SQUEEGEE DEFLECTION ADJUSTMENT  
KNOBS (DISK SCRUBBER)  
3. SQUEEGEE DEFLECTION ADJUSTMENT  
(CYLINDRICAL SCRUBBER)  
Adjusts the deflection along the entire length of  
the squeegee.  
Adjusts the deflection along the entire length of  
the squeegee.  
To increase squeegee blade deflection, turn the  
two knobs at the ends of the squeegee  
counterclockwise.  
To increase squeegee blade deflection, loosen  
the bolt at the wheel axle and raise in the slots.  
To decrease squeegee deflection, lower the  
wheel axle in the slots.  
To decrease squeegee deflection, turn the two  
knobs at the ends of the squeegee clockwise.  
4. SQUEEGEE PTICH ADJUSTMENT  
(CYLINDRICAL SCRUB)  
2. SQUEEGEE PITCH ADJUSTMENT ROD  
(DISK SCRUBBER)  
No adjustments are necessary for this squeegee  
style.  
Adjusts the deflection at the ends of the  
squeegee.  
To increase squeegee blade deflection at the  
ends, turn rod counterclockwise.  
To decrease squeegee blade deflection at the  
ends, turn rod clockwise.  
86317500 CHARIOT SCRUBBER 11/15/08  
3-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MACHINE OPERATION  
PRE-RUN MACHINE INSPECTION  
EMERGENCY STOP PROCEDURES  
Do a pre-run inspection to find possible problems  
that could cause poor performance or lost time from  
breakdown. Follow the same procedure each time to  
avoid missing steps.  
1. Push in emergency stop button. This will also  
engage the parking brake and cause the  
machine to stop immediately.  
NOTE: See maintenance section for pre-run  
machine inspection checklist items.  
STARTING MACHINE  
NOTE: Perform pre-run machine check before  
operating machine.  
FOR SAFETY: Before starting machine, make  
sure that all safety devices are in place and  
operating properly.  
1. The operator should be on the pedal platform.  
The throttle pedal must be in the neutral  
position.  
2. Turn the machine power on by turning key  
switch clockwise to the “ON” position.  
3. Check the position of the Directional Control  
Switch to make sure the machine will travel in  
the direction intended.  
4. Press the Drive Reset Directional Control Switch  
to reset and set the intended direction for travel.  
5. Press lightly on the throttle pedal with right foot.  
86317500 CHARIOT SCRUBBER 11/15/08  
3-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MACHINE OPERATION  
FILLING SOLUTION TANK  
NORMAL SCRUBBING  
FOR SAFETY: Before leaving or servicing  
machine; stop on level surface, turn off machine  
and remove key.  
Plan the scrubbing pattern in advance. The longest  
track is around the perimeter of the area to be  
cleaned. For efficient operation, the runs should be  
the longest possible without turning, stopping, or  
raising or lowering scrub deck/squeegee.  
1. Turn the machine power off.  
2. Remove solution cover.  
In order to achieve the best possible results, the  
area which is to be cleaned should be swept before  
scrubbing. Large debris, strings and wire must be  
removed to prevent being caught in brushes or  
squeegee.  
3. Fill the solution tank with clean water, leaving  
enough room for the required amount of  
cleaning solution. The solution tank capacity  
filled to fill inlet is 25 gallons (95 liters). The  
water must not be hotter than 140° F (60°C) to  
prevent damage to the tank.  
If the machine is allowed to stand in neutral with the  
scrub deck down for more than 2 seconds, the  
solutions flow stops and brush motors stop. If either  
forward or reverse travel is selected, the solution  
flow will continue in the same setting and the scrub  
brush motors will continue in their same setting once  
movement of machine begins. Overlap the brush  
path and avoid transporting over previously cleaned  
areas.  
4. Measure the chemical into the solution tank.  
The solution cover is also a 2 oz. (60 ml)  
measuring cup. Liquid chemicals should be  
added to the solution tank after filling with water.  
Dry chemicals should be thoroughly mixed  
before being added into solution tank.  
Commercially available, high alkaline floor  
cleaners, are suitable for use in the solution  
system.  
NOTE: Read the chemical manufacturers  
recommended proportion instructions.  
5. Replace solution tank cover.  
Flammable materials  
can cause an  
explosion or fire. Do not use flammable  
materials in the tanks.  
86317500 CHARIOT SCRUBBER 11/15/08  
3-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MACHINE OPERATION  
PRIMING PUMP  
TO BEGIN SCRUBBING  
If the solution system has gone dry or has been  
unused for a period of time, it may be necessary to  
follow the pump priming procedure.  
When operating the machine around people, pay  
close attention for unexpected movement. Use  
extra caution around children.  
1. Fill solution tank.  
Flammable liquids and/or reactive metals can  
cause explosions or fire! Do not pick up.  
2. Loosen, but do not completely remove the  
strainer bowl. Solution should flow out of the  
strainer. If it does not, check the strainer screen  
inside the solution tank. Insure it is clear of  
debris. Tighten the strainer bowl.  
1.  
Stand on the operator platform. Throttle pedal  
must be in neutral position.  
2.  
3.  
Turn machine power on.  
3. Disconnect the squeegee hose from the  
Press the Drive Reset / Directional Control  
Switch, selecting the desired travel direction.  
recovery dome.  
4. Begin normal scrubbing. Solution flow should  
4.  
Position the function control knob to the desired  
operation. The brush motors will start, the scrub  
deck will lower, the solution will begin to flow,  
the squeegee will lower to the floor and the  
vacuum motors will start.  
begin within 2 minutes.  
5. Connect squeegee hose to recovery dome.  
5.  
Drive machine forward to begin scrubbing.  
NOTE: Shut machine off immediately if water or  
foam is expelled from the machine.  
NOTE: Solution flow is automatically shut off when  
brush motors stop. When brush motors are  
activated, flow automatically resumes.  
86317500 CHARIOT SCRUBBER 11/15/08  
3-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MACHINE OPERATION  
TO STOP SCRUBBING  
DOUBLE SCRUB  
For floors which are heavily soiled or have thick  
accumulations of floor finish, may not clean  
sufficiently with one pass. In these cases it will be  
necessary to double scrub.  
Rotate the knob to the double scrub position labeled  
“C”, make the first pass over the surface being  
cleaned with the squeegee up, vacuum off and the  
solution on. For best results also remove the Aqua-  
mizer™, this will allow the solution to stay in contact  
with the soil while loosening the surface  
accumulation with the brushes. Allow time for the  
first application to stay in contact with the floor.  
Length of time between the first and second pass  
depends on amount of accumulation and the type of  
chemical being used. A second scrubbing with the  
function knob in one of the normal scrubbing modes  
will lower the squeegee and will keep the solution on  
and brushes down to further loosen soil. The  
additional application of solution will further assist  
the difficult cleaning job.  
1. Rotate the function knob to either transport  
position. The brush motors will stop and the  
scrub deck will rise to the park position. After 10  
seconds the squeegee will raise, and 10  
seconds later the vacuum motor will turn off.  
This delay is to clear the vacuum hose of  
recovered solution.  
2. Allow the throttle pedal to return to neutral.  
3. Turn machine power off.  
FOR SAFETY: Before leaving or servicing  
machine: stop on level surface, turn off machine  
and remove key.  
FOR SAFETY: When using machine, go slow on  
inclines and slippery services.  
86317500 CHARIOT SCRUBBER 11/15/08  
3-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MACHINE OPERATION  
SOLUTION TANK  
RECOVERY  
TANK DOME  
1. Remove the recovery tank dome.  
2. Pull the solution drain hose from its mounting  
pocket. Unscrew the cap, then lower hose in  
direction of drain.  
RECOVERY  
DRAIN HOSE  
3. Remove the solution tank lid.  
4. Flush the solution tank out with clean water and  
run several gallons of clean water through  
systems. Do not use water hotter than 140°F  
(60°C) to clean tank. Damage may occur.  
NOTE: Never allow solution to remain in tank.  
Damage to tank, seals and valves could occur.  
SOLUTION  
DRAIN HOSE  
EMPTYING AND CLEANING TANKS  
1.  
2.  
Park the machine next to a floor drain. Drain  
hoses are at the front of the machine.  
Turn the machine power off.  
RECOVERY TANK  
1.  
Remove the recovery tank dome. Pull the large  
drain hose from the mounting pocket. Unscrew  
cap, then lower hose in direction of the drain. Do  
not stand in front of end of hose. Recovered  
solution will come out with force.  
2.  
Flush the recovery bag out with clean water. Do  
not use water hotter than 140°F (60°C) to clean  
tank. Damage may occur.  
3.  
4.  
Clean debris from dome basket.  
Clean off the float shut-off system and inspect  
for free movement of float. The float shut-off  
system is located in the rear of the recovery  
tank.  
5.  
6.  
Replace the drain cap and secure drain hose  
under tank.  
If machine is to be stored, leave the recovery  
tank dome off, or propped open.  
86317500 CHARIOT SCRUBBER 11/15/08  
3-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES:  
86317500 CHARIOT SCRUBBER 11/15/08  
3-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
SERVICE SCHEDULE  
AFTER EACH  
WORK  
BEFORE EACH  
WORK PERIOD  
50  
HRS  
100  
HRS  
200  
HRS  
MAINTENANCE  
PERIOD  
Check water level of batteries after charging;  
add distilled water if necessary. (Wet cell only)  
Check that dome and cover seal tightly.  
Visually check for damaged or worn tires.  
Check brushes or pads for proper installation.  
Check vacuum hose connections.  
Check that squeegee is securely attached and  
properly adjusted.  
Check for securely attached drain hoses, plug  
and cap.  
Check pedal, brake and steering for proper  
operation.  
*
*
*
*
*
*
*
*
Clean out recovery tank and dome basket.  
Clean and inspect float shutoff.  
Clean out solution tank and filter, check flow.  
Clean and inspect solution filter strainer.  
Run vacuum motors to dry.  
Clean brushes or pads and check wear.  
Clean squeegee blades and check wear.  
Clean outside of tanks, check for damage.  
Store with dome off tank or propped open.  
Charge batteries if needed.  
*
*
*
*
*
*
*
*
*
*
Clean off top of batteries.  
*
Check battery cells with hydrometer. (Wet cell  
only)  
*
*
*
*
Inspect scrub deck skirts and Aqua-Mizers.  
Clean solution strainer inside tank.  
Check battery connections are tight.  
Clean battery cases and battery compartment.  
Check parking brake.  
*
*
*
Clean cables and pulleys for squeegee lift.  
Clean pivot points on squeegee and scrub  
deck.  
Check all motors for carbon brush wear.  
Check motor commutators.  
*
*
*
*
Check steering chain tensioner.  
NOTE: Traction drive, wheels and batteries should be serviced based on traction drive hour meter  
(Deluxe). The scrub brush hour meter should be used for all other service schedule items.  
86317500 CHARIOT SCRUBBER 11/15/08  
4-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-BATTERIES  
1
2
3
4
6
5
1.  
2.  
3.  
Rear Cover Retainer Knob  
Rear Cover  
Battery Connector-Machine  
4.  
5.  
6.  
Batteries  
Battery Tray  
Battery Tray Latch  
86317500 CHARIOT SCRUBBER 11/15/08  
4-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-BATTERIES  
BATTERIES (WET CELL ONLY)  
When servicing machine,  
avoid contact with battery  
acid.  
The batteries provide the power to operate the  
machine. The batteries require regular maintenance  
to keep them operating at peak efficiency.  
Batteries emit hydrogen  
gas. Explosion or fire can  
The machine batteries will hold their charge for long  
periods of time, but they can only be charged a  
certain number of times. To get the greatest life  
from the batteries, charge them when their charge  
level reaches 25% of a full charge. Use a  
result. Keep sparks and open flame away. Keep  
covers open when charging.  
Wear eye protection and  
protective clothing when  
working with batteries.  
hydrometer to check the charge level.  
Do not allow the batteries to remain in a discharged  
condition for any length of time. Never expose a  
discharged battery to temperatures below freezing.  
Discharged batteries will freeze causing cracked  
cases. Do not operate the machine if the batteries  
are in poor condition or if they have a charge level  
below 25% (specific gravity below 1.155).  
Charge batteries in a well  
ventilated area.  
BATTERY MAINTENANCE  
1. When cleaning the batteries, use a solution of  
baking soda and water. Do not allow the  
cleaning fluid to enter the battery cells,  
electrolyte will be neutralized.  
Keep all metallic objects off the top of the batteries,  
as they may cause a short circuit. Replace worn or  
damaged cables and terminals.  
2. Maintain the proper electrolyte level in each  
battery cell. If a cell should accidentally  
overflow, clean immediately.  
Check the electrolyte level in each battery cell  
before and after charging the batteries. Never add  
acid to the batteries, use distilled water. Do not  
allow water level to fall below the battery plates.  
Portions of plates exposed to air will be destroyed.  
Do not overfill. Keep plugs firmly in place at all  
times.  
3. Wipe off the top of the batteries at least once a  
week.  
4. Test battery condition with a hydrometer at least  
once a week.  
5. Ensure that all connections are tight and all  
corrosion removed.  
6. Every 4 to 6 months, remove that batteries from  
the machine and clean the battery cases and  
battery compartment.  
86317500 CHARIOT SCRUBBER 11/15/08  
4-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-BATTERIES  
CHECKING BATTERY SPECIFIC GRAVITY  
CHARGING BATTERIES  
Use a hydrometer to check the battery specific  
gravity.  
When servicing machine,  
avoid contact with battery  
acid.  
Batteries emit hydrogen  
gas. Explosion or fire can  
Battery Check  
result. Keep sparks and open flame away. Keep  
covers open when charging.  
Wear eye protection and  
protective clothing when  
working with batteries.  
Charge batteries in a well  
ventilated area.  
CHECKING GRAVITY  
A. Hydrometer  
B. Battery  
Use a 36 volt, 20 amp maximum output DC charger  
which will automatically shut off when the batteries  
are fully charged.  
NOTE: Do not take readings immediately after  
adding distilled water, if the water and acid are not  
thoroughly mixed, the reading may not be accurate.  
1. Stop the machine in a clean, well ventilated area  
next to the charger.  
Check the hydrometer readings against this chart.  
2. Turn “OFF” machine.  
FOR SAFETY: Before leaving or servicing  
machine; stop on level surface, turn off machine  
and remove key.  
SPECIFIC GRAVITY  
@ 80° F (27°C)  
1.265  
BATTERY CONDITION  
100% CHARGED  
75% CHARGED  
50% CHARGED  
25% CHARGED  
DISCHARGED  
1.225  
1.190  
1.155  
1.120  
3. Remove rear cover, unplug batteries from  
machine, unlatch battery tray and pull out to  
expose batteries.  
Batteries emit hydrogen  
gas. Explosion or fire  
can result. Keep sparks and open flame away.  
Keep covers open when charging.  
NOTE: If the readings are taken when the battery  
electrolyte is any temperature other than 80°F  
(27°C), the reading must be temperature corrected.  
To find the corrected specific gravity reading when  
the temperature of the battery electrolyte is other  
than 80°F (27°): Add (+) to the specific gravity  
reading 0.004 (4 points), for each 10°F (6°C) above  
80° (27°C).  
4. Check the electrolyte level in each battery cell.  
Before charging, add just enough distilled water  
to cover the plates. After charging is complete,  
add just enough distilled water to bring up the  
level to the indicator ring. If the water level is  
too high before charging, normal expansion rate  
of the electrolyte may cause an overflow  
resulting in a loss of battery acid balance and  
damage the machine.  
Subtract (-) from the specific reading 0.004 (4  
points), for each 10°F (6°C) below 80°F (27°C).  
86317500 CHARIOT SCRUBBER 11/15/08  
4-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-BATTERIES  
CHANGING BATTERIES  
5. Replace the battery caps, and leave them in  
place while charging.  
Stop the machine in a clean area next to the  
charger. Turn off machine.  
6. Unplug the battery connector from the machine.  
FOR SAFETY: Before leaving or servicing the  
machine; stop on level surface, turn off machine  
and remove key.  
FOR SAFETY: When charging, connect the  
charger to the batteries before connecting the  
charger to the AC wall outlet. Never connect the  
charger to the AC wall outlet first. Hazardous  
sparks may result.  
1.  
2.  
3.  
Remove the rear cover.  
Disconnect battery pack from machine.  
7. Plug the charger connector into the battery  
connector. Connect the charger AC plug to a  
wall outlet. The charger gauge should indicate  
that the batteries are charging.  
Unlatch battery tray from machine and pull out  
to expose batteries.  
4.  
Use the proper size open end wrench to  
disconnect main ground wire first and secure  
cable terminal away from batteries.  
8. When the batteries are fully charged, disconnect  
the charger from the AC wall outlet, then  
disconnect the charger from the batteries.  
5.  
6.  
7.  
Disconnect main positive lead and secure cable  
terminals away from batteries.  
9. Connect the batteries to the machine connector.  
Loosen both terminals on each jumper cable  
and remove one at a time.  
10. Check the electrolyte level. It should be up to  
the indicator ring. If necessary, add distilled  
water.  
Prepare a suitable site to place the batteries.  
11. Install the rear cover.  
Attach suitable battery lifting  
device and lift batteries from  
the machine. Batteries are a  
potential environmental hazard. Consult your battery  
supplier for safe disposal methods.  
RED  
RED  
RED  
+
+
+
-
-
-
BLK  
BLK  
BLK  
REAR OF MACHINE  
86317500 CHARIOT SCRUBBER 11/15/08  
4-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-SQUEEGEE  
6
4
5
1
2
3
4.  
5.  
6.  
Squeegee Pitch Adjustment Rod  
Squeegee Pitch Adjustment Lock Nut  
Squeegee Retainer Knob  
1.  
2.  
3.  
Squeegee  
Squeegee Deflection Adjustment Knobs  
Squeegee Level Indicator  
86317500 CHARIOT SCRUBBER 11/15/08  
4-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-SQUEEGEE  
SQUEEGEE BLADES  
TO REMOVE SQUEEGEE ASSEMBLY  
The front squeegee blade allows solution to pass  
through channels in the blade into the squeegee  
assembly while maintaining vacuum to provide lift.  
The front blade has four wear surfaces and can be  
rotated for extended life. The front blade should not  
require regular replacement under normal use.  
1. With the squeegee in the up position, turn key  
switch “OFF”.  
2. Disconnect vacuum hose from squeegee and  
loosen knob on left side of squeegee lifting  
carrier.  
The rear blade wipes the floor to a near dry  
condition. It is important the rear blade be in good  
condition to properly do its job. As with the front,  
each squeegee blade assembly has four wear  
surfaces for extended service.  
3. Pull squeegee assembly from the lifting carrier.  
4. Inspect or repair as necessary and reinstall.  
TO REPLACE OR ROTATE REAR SQUEEGEE  
BLADES  
Check both the front and rear squeegee blades for  
damage, wear, and adjustment each day in the pre-  
run check. Change the front blade if it is torn or has  
an uneven edge. Change the rear blade if it is less  
than 1/2 the original thickness.  
1. With the squeegee in the up position, turn key  
switch “OFF”.  
FOR SAFETY: Before leaving or servicing  
machine; stop on level surface, turn off machine  
and remove key.  
ADJUSTING SQUEEGEE  
2. Remove the squeegee assembly from the  
machine. Unlatch and remove blade retainer  
strap and remove squeegee blade.  
Adjusting the squeegee is a two-part process. First,  
the squeegee assembly must have correct pitch in  
order for the squeegee blade to have the same  
deflection at each tip as well as the center. The rod  
on the squeegee linkage controls the pitch  
adjustment. The second adjustment is the  
deflection. Knobs on each end of the squeegee  
control this.  
3. Rotate the squeegee to new edge position or  
replace as required. Each blade has four new  
edge positions.  
4. Install blade on locating pins of squeegee  
assembly.  
SQUEEGEE DEFLECTION  
5. Install squeegee retainer strap.  
3
"
8
(9.5mm)  
6. Fasten and lock latch, adjust latch only tight  
enough to take up slack in retaining strap.  
CORRECT  
TO REPLACE OR ROTATE FRONT SQUEEGEE  
BLADE  
1. With the squeegee in the up position, turn key  
NOT ENOUGH  
switch “OFF”.  
2. Remove the squeegee from the machine.  
Loosen thumbscrews and remove the retainer  
strap and squeegee blade.  
TOO MUCH  
3. Rotate the squeegee to new edge position or  
replace as required. Each blade has four new  
edge positions. When installing the front blade,  
tighten the center thumbscrew first. Insure that  
the retainer strap is pressed against the blade  
before tightening the outer screws.  
SIDE VIEW OF SQUEEGEE BLADE  
86317500 CHARIOT SCRUBBER 11/15/08  
4-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-SQUEEGEE  
TO ADJUST SQUEEGEE PITCH  
TO ADJUST AMOUNT OF REAR SQUEEGEE  
DEFLECTION  
1. Choose a smooth, level surface. Turn “ON” the  
key switch. Lower the squeegee and drive  
forward at least 2 feet (60cm.).  
SQUEEGEE DEFLECTION  
2. With the squeegee down, stop the machine. Do  
3
"
not allow machine to roll back.  
8
(9.5mm)  
FOR SAFETY: Before leaving or servicing the  
machine; stop on level surface, turn off machine  
and remove key.  
CORRECT  
3. Determine the differences, if any, in deflection of  
the squeegee blade between each end and the  
middle. Proper adjustment is obtained when  
deflection is equal all the way across the  
squeegee blade. The bubble level should also  
indicate when the squeegee is adjusted  
properly. When the air bubble is in the center of  
the vial, the deflection should be even across  
the squeegee blade.  
SIDE VIEW OF SQUEEGEE BLADE  
1. Choose a smooth, level surface. Lower the  
squeegee and drive forward at least 2 feet  
(60cm).  
2. With the squeegee down, stop the machine. Do  
not allow machine to roll back.  
4. To decrease the deflection of the squeegee  
blade at the ends, loosen wing nut and rotate  
the rod clockwise. To increase the deflection at  
the ends of the squeegee assembly, rotate the  
rod counterclockwise knob.  
FOR SAFETY: Before leaving or servicing  
machine; stop on level surface, turn off machine  
and remove key.  
3. Observe the amount of squeegee deflection. It  
should deflect 3/8 in. (9.5mm) across the entire  
width of the squeegee.  
5. Check the deflection of the squeegee blades  
again. Repeat steps 1 through 4 until the  
deflection is equal across the entire rear  
squeegee blade. Tighten wing nut.  
4. To increase the squeegee deflection, turn the 2  
knobs at the squeegee ends counter-clockwise.  
To decrease the deflection, turn the knobs  
clockwise.  
NOTE: The deflection should be consistent along  
the length of the squeegee. If the deflection varies  
from end to end the knobs can be adjusted  
independently to correct the variation.  
5. Turn on the key switch. Raise, then lower  
squeegee assembly. Drive forward at least  
2 feet (60cm).  
6. Repeat steps 2 through 4 until deflection of  
3/8 in. (9.5mm) is reached.  
86317500 CHARIOT SCRUBBER 11/15/08  
4-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-SCRUB BRUSHES  
SCRUB BRUSHES  
FINISHED FLOORS  
There are four different types of brushes available to  
cover applications from cleaning heavily soiled floors  
to polishing. A pad driver is also available to take  
advantage of the many cleaning pads on the market.  
Please refer to the following to assist in selecting the  
proper brush or pad for the work at hand.  
Nylon bristles are used in a variety of applications  
on coated or uncoated surfaces.  
White Pads (Polishing) are used for dry polishing to  
achieve a high-gloss appearance, or surface  
washing on highly polished or burnished floors.  
Red Pads (Buffing) are used for light-duty  
scrubbing. When used with a mild detergent they  
will provide surface cleaning without removing the  
finish.  
UNCOATED FLOORS  
Aggressive Grit is a nylon fiber impregnated with  
silicone carbide grit. It grinds away stain, soil, and  
removes surface material.  
Blue Pads (Scrubbing) are used for heavy-duty  
scrubbing and light stripping. The blue pads remove  
less finish than brown stripping pads, yet will remove  
black marks, stains and dirt.  
Mild Grit is a less aggressive silicone carbide grit  
suitable for cleaning medium soil conditions.  
Advantages are faster ground speed than nylon  
bristles on light solid applications.  
Black Pads (Stripping) are used for easy and  
complete removal of old floor waxes/finishes. They  
will quickly remove ground in dirt, black heel marks,  
and spills. When used with the proper stripper, this  
pad leaves the floor clean and ready for finishing.  
Polypropylene is a general-purpose scrub brush  
with stiff bristles. Polypropylene works well for  
maintaining concrete, wood and tile floors.  
The scrub brushes should be checked before each  
days work for wire, string, wear and damage.  
86317500 CHARIOT SCRUBBER 11/15/08  
4-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-SCRUB DECK  
4
3
1
2
5
6
1. Scrub deck Aqua-Mizer™  
2. Aqua-Mizer™ retainer knob  
3. Scrub deck skirt  
4. Scrub deck skirt stop  
5. Scrub brush motor  
6. Scrub deck lift actuator  
86317500 CHARIOT SCRUBBER 11/15/08  
4-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-SCRUB DECK  
Do not use a pressure  
washer to clean around  
BRUSH MOTOR CARBON BRUSH  
REPLACEMENT  
the brush motors. Use tap pressure only.  
1. Scribe alignment mark on motor barrel to motor  
TO REPLACE SCRUB BRUSH MOTORS  
cap. Remove two bolts.  
1. With the scrub deck in the raised position,  
disconnect brush motor wiring connector from  
harness.  
2. Remove end cap from motor.  
NOTE: Motors contain two wave washers in  
cap. Do not lose these.  
2. Remove skirts from scrub deck to access and  
3. Release brush from spring tension. Remove  
screw connecting brush wire lead to brush  
holder. Clean brush holder to insure free  
movement.  
remove scrub brushes or pad drivers.  
3. Remove Aqua-Mizers™ from scrub deck.  
4. Remove retaining bolt, lock washer, flat washer  
4. Retract spring and install new brush. Install  
and star drive from brush motor shaft.  
connector screw and lead.  
5. Remove 4 brush motor mounting bolts located  
5. When all new brushes are installed. Place all in  
retracted position, held into brush holder by  
spring tension.  
under scrub deck.  
6. Lower scrub deck.  
6. Carefully place end cap onto bearing on motor  
7. Remove brush motor.  
8. Reverse steps to install.  
shaft.  
NOTE: Use care to assure wave washer  
alignment.  
7. With end cap in partially installed position,  
release all brushes to contact position with  
motor commutator.  
NOTE: Failure to insure all brushes are released  
will result in motor failure.  
8. Reset end cap and realign with scribe marks on  
motor barrel. Reinstall the two attach bolts from  
cap into base.  
9. Maintain alignment between motor barrel base  
and cap.  
86317500 CHARIOT SCRUBBER 11/15/08  
4-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-SCRUB DECK  
ACTUATOR SCRUB DECK  
REMOVAL/REPLACEMENT  
SCRUB DECK ACTUATOR ADJUSTMENT  
The actuator will need to be adjusted when  
replaced.  
FOR SAFETY: Before leaving or servicing  
machine, stop on a level surface. Turn off  
machine.  
To adjust the actuator:  
1. Remove the two screws that secure actuator  
spring plate and pull actuator barrel from stud on  
actuator spring bracket.  
1. While holding actuator barrel to prevent it from  
spinning, apply power to the actuator such that it  
is fully extended. Positive power to white wire,  
and negative/ground to black. Limit switch  
within actuator will stop it.  
2. Remove clevis pin from upper bracket of  
actuator.  
2. Turn barrel out one or more full turns to assure  
that when it is retracted it will not bind against  
itself.  
3. Disconnect actuator from wiring harness.  
4. Reverse steps to install.  
3. While holding actuator barrel to prevent it from  
spinning, apply power to the actuator such that it  
is fully retracted. Positive power to black wire,  
and negative/ground to white wire. Limit switch  
within actuator will stop it.  
4. With actuator fully retracted, turn barrel in until it  
touches the base of the threaded shaft.  
5. At the bottomed out position, turn the barrel out  
1 full turn, then enough more to allow  
connection to lift linkage.  
6. Connect actuator to lift linkage.  
7. Check travel of actuator during operation.  
86317500 CHARIOT SCRUBBER 11/15/08  
4-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-CIRCUIT PROTECTION  
1
1.  
CIRCUIT BREAKERS  
Circuit breakers interrupt the flow of power in the  
event of an electrical overload. When a circuit  
breaker is tripped, reset it by pressing the  
exposed button. If a circuit breaker continues to  
trip, the cause of the electrical overload should  
be found and corrected.  
18 Amp. Protects the left scrub  
brush motor.  
18 Amp. Protects the right scrub  
brush motor.  
86317500 CHARIOT SCRUBBER 11/15/08  
4-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-SOLUTION STRAINER & PUMP-DISK  
1
5
6
2
3
4
1. Solution Strainer-Coarse  
2. Solution Strainer-Fine  
3. Pump  
4. Pump Mounting Plate  
5. Solenoid Valve  
6. Shut-off Valve  
86317500 CHARIOT SCRUBBER 11/15/08  
4-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-SOLUTION STRAINER & PUMP-CYLINDRICAL  
1
3
5
2
4
6
1. Solution Strainer-Coarse  
2. Solution Strainer-Fine  
3. Pump  
4. Solenoid Valve  
5. Jets  
6. Shut-off Valve  
86317500 CHARIOT SCRUBBER 11/15/08  
4-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-SOLUTION STRAINER & PUMP  
1.  
SOLUTION STRAINER-COARSE  
3.  
PUMP  
Located in bottom of tank. The coarse strainer  
protects the finer strainer from large debris. If  
the fine strainer is clean and the pump and  
solenoid valve are not working, then check the  
coarse strainer for debris. Drain the solution  
tank and clean the coarse strainer. To remove  
the strainer, rotate the strainer counterclockwise.  
Cleanout the debris from wire mesh and re-  
assemble.  
The pump is located under the tank on the right  
side of machine. The pump delivers solution  
from the tank to the scrub deck.  
To repair or replace pump:  
1. Remove scrub deck skirts, Aqua-Mizer, and  
squeegee from machine.  
2. Lower scrub deck to gain access to pump  
mounting plate.  
2.  
SOLUTION STRAINER (FINE) AND  
SHUT-OFF VALVE  
3. Remove screw that secures pump mounting  
plate to frame.  
The fine strainer is located in front left corner of  
machine on disk models and in right rear corner  
of cylindrical models. The fine strainer protects  
the pump and solenoid valve from debris. If  
there is little or no solution flow to the ground,  
first check to make sue the shut-off valve is  
open. Next, check the strainer for debris. To  
remove the strainer, first turn the shut-off valve  
to the off position. Then, turn the bottom part of  
the strainer counterclockwise until the bottom is  
separated. Clean out the debris from the wire  
mesh and re-assemble. Make sure the O-ring  
gasket is in place when re-assembled. To  
resume flow, turn the shut-off valve to the open  
position.  
4. The pump is located under the tank on the  
right side of machine. The pump delivers  
solution from the tank to the scrub deck. Pull  
pump mounting plate forward and down to  
expose pump.  
5. Reverse steps to install.  
4.  
5.  
PUMP MOUNTING PLATE  
See graphic representation on previous page.  
SOLENOID VALVE  
The solenoid valve is mounted on the front of  
the scrub deck, on left side.  
The solenoid valve shuts off solution flow to  
scrub deck whenever scrubbing stops. To repair  
or replace solenoid valve, cut cable ties that  
secure it to deck.  
86317500 CHARIOT SCRUBBER 11/15/08  
4-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-VACUUM & FLOAT SHUT-OFF  
1
2
1.  
2.  
Recovery tank float shut-off  
Vacuum motor  
86317500 CHARIOT SCRUBBER 11/15/08  
4-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-VACUUM & FLOAT SHUT-OFF  
FOR SAFETY: before leaving or servicing  
machine, stop on a level surface, turn off  
RECOVERY TANK FLOAT SHUT-OFF  
machine and disconnect power.  
When water is no longer being vacuumed from  
the floor and the vacuum fan is operating, the  
ball float has engaged. The vacuum motor will  
not vacuum water with recovery tank full. The  
recovery tank must be drained.  
TO REPAIR OR REPLACE VACUUM MOTOR  
1.  
2.  
Remove rear cover from machine.  
Remove two screws from top of control  
panel and four screws from sides of control  
housing.  
1.  
2.  
The float shut-off screen can be cleaned in or  
out of the machine.  
To clean the float shut-off while it is inside the  
machine wipe material off screen then rinse.  
Check that the ball is also clean and moves  
freely.  
3.  
4.  
Slide control housing back from tank to  
expose vacuum motor.  
Disconnect electrical connector from the  
vacuum motor. Remove the muffler hose  
from the vacuum motor outlet.  
3.  
4.  
To remove the float shut-off, grasp the screen  
with one hand and the connected tube with the  
other. Tilt and pull the float screen assembly to  
pull it off the barb on the tube.  
5.  
6.  
Remove three nuts that secure vacuum  
motor.  
To install, place one hand on the tube, and then  
tilt and push the float screen assembly over the  
barb on the tube.  
Reverse steps to install. Make sure that  
gasket is on vacuum so that vacuum seals  
against tank  
Vacuum Motor Carbon Brushes  
End Cap  
Carbon  
Brushes  
If armature commutator is grooved, extremely pitted or not  
concentric, the motor will need to be replaced or sent to a  
qualified service center.  
Important:  
These brushes wear quicker as the length shortens due to  
increased heat. Spring inside brush housing will damage  
motor if brushes are allowed to wear away completely.  
3
8
[9.5mm]  
Periodically check the length of the carbon brushes. Replace  
both carbon brushes when either is less than 3/8" (9.5mm)  
long.  
86317500 CHARIOT SCRUBBER 11/15/08  
4-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-DRIVE MOTOR & BRAKE  
2
1
1.  
2.  
Drive motor  
Parking brake  
86317500 CHARIOT SCRUBBER 11/15/08  
4-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-DRIVE MOTOR & BRAKE  
ELECTRIC PARKING BRAKE ENGAGEMENT  
To disengage brake:  
FOR SAFETY: Before leaving or servicing  
machine, stop on a level surface, turn off  
machine and remove key.  
Electric Brake Engagement  
This machine is equipped with an electric parking  
brake.  
The brake automatically engages and keeps the  
machine from moving whenever the operator steps  
off the platform or when emergency stop is engaged.  
The brake has a mechanical over-ride that can be  
engaged so machine can be pushed or towed  
(slowly).  
1. Mechanical over-ride disengaged  
When the mechanical over-ride is engaged the  
machine cannot be driven.  
Machine can be driven.  
2. Push lever firmly in direction of arrow.  
To engage brake:  
1. Mechanical over-ride engaged.  
Machine can be pushed or towed (slowly).  
2. Push lever firmly in direction of arrow  
Note: There is an intermediate stop. Make sure  
lever is fully in the down position.  
86317500 CHARIOT SCRUBBER 11/15/08  
4-20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-DRIVE MOTOR & BRAKE  
DRIVE MOTOR CARBON BRUSH REPLACEMENT  
5.  
Install new brush and reinstall connecting screw  
and lead.  
Do not use a pressure  
washer to clean around  
the motors. Use tap pressure only.  
6.  
When all new brushes are installed. Place all in  
retracted position, held into brush holder by  
spring tension.  
FOR SAFETY: Before leaving or servicing  
machine, stop on a level surface, turn off  
machine and remove key.  
7.  
Carefully replace brush cap.  
Reinstalling:  
1. Disconnect batteries from machine.  
10. When replacing the hex hub, use a small pin or  
screw to help align the holes.  
2. Disconnect the electrical connection to the  
traction motor.  
11. Drive the pin into the hub and make sure it is  
flush to the hex surface. The brake will not fit on  
the hub if the roll pin is protruding from the hub.  
BRAKE REMOVAL  
(Must be done to access carbon brushes)  
12. Replace the hub and use Lock-Tite on the  
3. Remove 4 mounting screws and remove brake.  
screws.  
4. Drive roll pin out of the hex hub enough to allow  
hex hub to slide off shaft. It is recommended  
that the roll pin be left partially in the hex hub.  
5. Remove brush cap.  
ROLL PIN  
HEX HUB  
SMALL PIN OR SCREW  
6. Release brush from spring tension. Remove  
screw connecting brush wire lead to brush  
holder. Clean brush holder to insure free  
movement.  
86317500 CHARIOT SCRUBBER 11/15/08  
4-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-BAG REPLACEMENT  
REMOVING OR REPLACING BAG  
8. Re-assemble frame, collar and bag if they  
were disassembled.  
1. Disconnect batteries and make sure parking brake  
is not overridden.  
9. Place bag assembly into tank.  
2. Remove Dome and set aside.  
10. Align bag drain hole with fitting in bottom of  
tank and thread in mandrel with washer  
attached. Turn clockwise to tighten. Tighten  
only by hand, do use a tool. Ensure mandrel is  
tight, the bag should be unable to move or  
spin around the mandrel.  
3. Drain all solution from both sides of the bag and  
rinse well.  
4. Remove float cage, loosen screw on elbow and  
remove elbow. (You can remove the bag by only  
removing the float cage and sliding the bag  
opening over the elbows.)  
11. Seat the collar, gasket, frame assembly to the  
tank rim opening. At the same time slide the  
vacuum collar opening over the float cage  
elbow assembly.  
5. Remove threaded mandrel from the bottom of the  
bag. Turn counterclockwise, remove by grabbing  
the attached handle. The mandrel washer should  
come off with the mandrel.  
12. Replace the rest of the elbow and float cage  
assembly with its mounting screw, if it was  
removed.  
6. Lift the bag assembly out of the tank. The dome  
gasket, plastic collar, and metal frame can all be  
removed as one assembly. The bag can be  
13. Install dome and connect squeegee hose.  
cleaned as an assembly or further disassembled.  
7. To replace with a new bag remove the four screws  
that go through the collar and into the frame.  
Feed the frame through the loops at the top of the  
bag.  
86317500 CHARIOT SCRUBBER 11/15/08  
4-22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-BAG TRANSPORTING  
PUSHING MACHINE  
PREPARATION FOR LOADING /UNLOADING  
TRAILER  
The machine may be pushed for short distances at  
speeds not to exceed 5 mph. Be careful to avoid  
damaging machine. The machine may be pushed by  
hand from the rear.  
NOTE: To avoid damage caused by regenerative  
voltage, disconnect traction motor before towing or  
pushing machine.  
Before loading or unloading machine from trailer,  
remove squeegee, scrub deck, side skirts or side  
squeegees, Aqua-Mizers and scrub brushes  
(pads) to eliminate interference with tie-downs.  
Scrub head must be in the up position before  
loading.  
MACHINE TIE-DOWNS  
NOTE: When transporting the machine on a trailer  
or in a truck, in addition to using tie-downs, be  
sure to set the parking brake, and block the tires to  
prevent the machine from rolling.  
There are two tie points located at front and each side  
of foot box frame and two at the front side of frame.  
Tie-down devices must be of the proper type and  
strength. The combined strength of all tie-downs must  
be strong enough to lift two times the weight of the  
machine. Tie-downs must be positioned to prevent  
the machine from moving forward, backward, or either  
side to side. Use all four corners of the machine with  
the tie-downs running out opposite directions. Tie-  
downs must be attached to the transporting vehicle  
securely.  
TIE DOWN POINTS  
86317500 CHARIOT SCRUBBER 11/15/08  
4-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE-TROUBLESHOOTING  
PROBLEM  
No power to machine  
CAUSE  
Battery disconnected  
SOLUTION  
Check all battery cable connections  
Emergency shut-off activated  
Reset  
Battery cables corroded  
Faulty key switch  
Clean connections  
Replace switch  
Little or no propel  
Low battery charge  
Charge batteries  
Machine turned on with pedal not in neutral  
position  
Allow pedal to return to neutral.  
Restart  
Tripped circuit breaker  
Wheels spin  
Controller overheated  
Reset circuit breaker  
Decrease brush pressure  
Allow cool down period  
Loose motor connection  
Check wires and connections from controller  
to motor  
Faulty throttle circuit or potentiometer  
Check wires and connections from and  
potentiometer resistance  
Faulty drive reset circuit or switch  
Faulty platform circuit or switch  
Brake over-ride engaged  
Check wires, connections and switch  
Check wires, connections and switch  
Disengage brake over-ride  
Faulty brake circuit or over-ride switch  
Faulty speed control circuit or switch  
Check wires, connections and switch  
Check wires & connections  
Machine does not  
change speeds  
Forward speed only  
Reverse speed only  
Faulty forward/reverse circuit  
Check wires & connections  
Poor or no water pickup Squeegee out of adjustment  
Adjust squeegee  
Debris caught on squeegee  
Remove debris  
Worn squeegee blades  
Rotate or replace squeegee blades  
Clear obstruction from hose  
Reconnect vacuum hose  
Vacuum hose clogged  
Vacuum hose disconnected from squeegee  
or recovery tank dome  
Recovery tank float system dirty  
Clean float system  
Recovery tank not sealed  
Place recovery tank dome on tank. Replace  
damaged gaskets  
Float-ball shut-off engaged Tank full  
Foam filling recovery tank  
Empty recovery tank  
Empty recovery tank. Use less or different  
detergent. Use defoamer.  
86317500 CHARIOT SCRUBBER 11/15/08  
4-24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MACHINE TROUBLESHOOTING  
PROBLEM  
CAUSE  
SOLUTION  
Vacuum motor does not run, or runs  
slowly  
Faulty vacuum circuit or switch  
Check wires & connections  
Worn vacuum motor brushes  
Faulty circuit or actuator  
Replace brushes, check commutator  
Check wires, connectors and actuator  
Squeegee will not go up/down  
Faulty cables or pulleys  
Debris caught in scrub brushes  
Worn brushes or pads  
Repair/replace cables or pulleys  
Remove debris  
Poor scrubbing performance  
Replace brushes or pads  
Improper detergent, brush or pad  
used  
Contact equipment or application  
specialists  
Low scrub brush down pressure  
Increase brush pressure  
Low battery charge  
Charge batteries  
Little or no solution flow to the floor  
Solution tank empty  
Solution strainer plugged  
Fill solution tank  
Clean solution strainer  
Solution system plumbing obstructed Clear obstruction from plumbing  
Pump obstructed Clean or replace pump  
Solution solenoid valve obstructed or Clean or replace valve  
stuck  
Solution shut-off valve is closed  
Faulty pump circuit or pump  
Faulty solenoid  
Open shut-off valve  
Check wiring, connections, and pump.  
Check solenoid valve  
Brush motors do not run, or run  
slowly  
Circuit breaker(s) tripped  
Low battery charge  
Reset circuit beaker(s)  
Charge battery  
Fault brush circuit or motor  
Worn brush motor brushes  
Faulty actuator circuit or actuator  
Check wires, connections and motor  
Replace brushes, check commutator  
Check wires, connections and  
actuator  
Scrub deck goes down, then raises  
No brushes or pad drivers on  
machine  
Install brushes or pad drivers  
86307500 CHARIOT SCRUBBER 11/15/08  
4-25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MACHINE TROUBLESHOOTING- CONTROLLER FAULT CODES  
ERROR  
CODE  
PROBLEM  
SOLUTION  
DELUXE  
THE BATTERY NEEDS CHARGING OR THERE IS A BAD  
CONNECTION TO THE BATTERY  
LOW BATTERY VOLTAGE  
THE TRACTION MOTOR HAS A BAD CONNECTION,  
CHECK CONNECTIONS TO MOTOR  
TRACTION MOTOR DISCONNECTED  
BRUSH MOTOR DISCONNECTED  
THE BRUSH MOTOR HAS A BAD CONNECTION, CHECK  
CONNECTIONS TO MOTOR  
CHECK AUX OUTPUT DEVICES, CHECK ALL  
ASSOCIATED WIRING TO AUX DEVICES  
AUX FAULT  
THE VACUUM MOTOR HAS A BAD CONNECTION,  
CHECK CONNECTIONS TO MOTOR  
VACUUM MOTOR DISCONNECTED  
CONTROL SYSTEM INHIBITED  
THROTTLE TRIP ERROR  
THE TRIO IS BEING INHIBITED FROM DRIVING, IE, ON-  
BOARD CHARGER IS IN USE  
THE THROTTLE IS DEFLECTED OR ASSOCIATED WIRING  
HAS A BREAK OR SHORT CIRCUIT  
THE CONTROL SYSTEM IS IN ERROR, CHECK ALL  
CONNECTIONS TO CONTROLLER  
CONTROL SYSTEM TRIP  
SOLENOID BRAKE  
THE SOLENOID HAS A BAD CONNECTION , CHECK  
CONNECTION TO BRAKE  
EXCESSIVE BATTERY VOLTAGE, CHECK FOR POOR  
BATTERY CONDITION  
HIGH BATTERY VOLTAGE  
4-26  
86317500 CHARIOT SCRUBBER 11/15/08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES:  
86317500 CHARIOT SCRUBBER 11/15/08  
4-27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS  
86317500 CHARIOT SCRUBBER 11/15/08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BUMPER  
1
4
8
9
2
6
1
5
3
4
7
10  
86317500 CHARIOT SCRUBBER 11/15/08  
5-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BUMPER  
PART  
NO.  
PRV  
NO.  
SERIAL NO.  
FROM  
REF  
QTY  
DESCRIPTION  
NOTES  
1
2
3
4
5
6
7
8
9
86270830  
86197040  
86276070  
86276890  
86010670  
86279130  
57023  
57264  
70593  
70752  
87029  
87083  
4
4
2
6
4
4
2
1
1
1
NUT, 5/16-18 HEX NYLOCK SS  
NUT, 5/16-18 HEX ACORN  
SCR, 5/16-18 X 3/4 CARRIAGE SS  
SCR, 5/16-18X3/4 PTHMS SS  
WASHER, 5/16 X 3/4 SS  
WASHER, 5/16 SPLIT LOCK PLTD  
BRKT, BUMPER MOUNT, SIDE  
BRKT, BUMPER MTG  
86070730 140729  
86315790  
86314170  
86314180  
-
-
-
BUMPER, LEFT  
BUMPER, RIGHT  
10  
86317500 CHARIOT SCRUBBER 11/15/08  
5-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROL PANEL  
24  
13  
23  
25  
17  
30  
19A  
19B  
6
8
16  
21  
12  
7
26  
1
2
15  
10  
18  
10  
14  
4
3
SUPPLED WITH  
HARNESS  
5
29  
SUPPLED WITH  
CONTROLLER  
28  
11  
27  
22  
20  
9
5-3  
86317500 CHARIOT SCRUBBER 11/15/08  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROL PANEL  
PRV  
NO.  
SERIAL NO.  
FROM  
REF PART NO.  
QTY  
DESCRIPTION  
METER, HOUR ICD  
NUT, 1/4-20 HEX NYLOCK SS  
NUT, 5/16-18 HEX NYLOCK THN SS  
NUT, 5/16-18 FLEXLOCK  
RELAY, 5A, 24V, 4PDT  
SCR, 1/4-20 X 1.25 HHCS SS  
SCR, 5/16-18 X 1.00 HHCS GR8  
SCR, 5/16-18X1/2 PTHMS SS  
SWITCH, KEY DPST  
STANDOFF, 6-32 X 5/8 HEX NYL  
STANDOFF, 1/4-20 X 1.0 HEX INS  
CONNECTOR, BATTERY GRY,  
175AMP  
NOTES  
1
2
3
4
5
6
7
8
9
86315470  
86005810  
86271840  
86271910  
86313900  
86273820  
86275760  
86277480  
86007190  
86255900  
86255910  
1
2
3
1
2
2
1
3
1
57245  
57285  
57295  
-
70019  
70540  
70850  
72161  
73538  
73659  
10  
11  
14  
1
12  
86008760  
80682  
1
13  
14  
15  
16  
17  
18  
86008900  
86010670  
86068850  
86070720  
86295200  
86012670  
80845  
87029  
140219  
140728  
-
2
1
1
1
1
1
BOOT, SEAL PUSH BUTTON 7/16  
WASHER, 5/16 X 3/4 SS  
BRKT, CABLE ATTACH  
BRKT, BATT CONN BASIC  
ASM, BUTTON, BLACK, W/BEZEL  
METER, 36V BATTERY  
-
CONTROLLER, 2-STAGE, GEAR  
DRIVE  
19A  
86315400  
-
1
DISK  
19B  
20  
21  
86318040  
86292590  
86313820  
86273830  
-
-
-
1
1
1
1
CONTROLLER, GEAR DRIVE CYL  
SWITCH, E-STOP AKW CHARIOT  
SWITCH, ROTARY, 7 POSN  
SCR, 1/4-20 X 1/2 HHCS SS NP  
SWITCH, SPDT 3 POSN MOM,  
ARROW  
CYLINDRICAL  
22  
70020  
23  
86313950  
-
1
24  
25  
26  
27  
28  
29  
86314150  
86315640  
86316160  
86010780  
86292780  
86270990  
-
-
-
1
1
2
1
1
2
KNOB, SELECTOR  
PANEL, CONTROL  
BREAKER, 18A, 250VAC, 32VDC  
WASHER, 1/4 SPLIT LOCK PLTD  
SWITCH, MICRO  
87162  
-
57090  
NUT, 10-32 HEX NYLOCK SS  
86317500 CHARIOT SCRUBBER 11/15/08  
5-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROL PANEL HOUSING  
2
3
5
3
1
6
11  
4
7
10  
9
8
86317500 CHARIOT SCRUBBER 11/15/08  
5-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROL PANEL HOUSING  
SERIAL NO.  
REF PART NO.  
PRV NO. QTY  
DESCRIPTION  
NUT, 1/4-20 HEX NYLOCK SS  
SCR, 10-32 X 1/2 TORX SS BLK NP  
SCR, 5/16-18 X1/2 PTHMS SS  
BRKT, LEFT CONSOLE MOUNT  
GASKET, .125 X .25W X 23L  
CONSOLE  
FROM  
NOTES:  
1
2
3
4
5
6
7
86005810  
86290540  
86277480  
86317890  
86237900  
86031730  
86317900  
57245  
4
6
6
1
3
1
1
-
70850  
-
35278  
270084  
-
BRKT, RIGHT CONSOLE MOUNT  
WASHER, RET, PUSHNUT, 5/16  
BOLT  
8
86279750  
87252  
4
9
86089650  
86277420  
86010630  
78524  
70841  
87013  
4
4
4
TUBE, 5/8 OD X .357 ID X 1.57  
SCR, 5/16-18 X 2.5 PTHMS SS  
WASHER, 1/4 ID X 5/8 OD SS  
10  
11  
86317500 CHARIOT SCRUBBER 11/15/08  
5-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECAL  
3
2
5
4
1
6
86317500 CHARIOT SCRUBBER 11/15/08  
5-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECAL  
SERIAL NO.  
FROM  
REF PART NO.  
PRV NO. QTY  
DESCRIPTION  
NOTES:  
1A  
1B  
2A  
86318570  
86318590  
86318580  
-
-
-
1
1
1
LABEL, CHAR, ISCURB 24, LEFT  
LABEL, CHAR, ISCRUB 26C, LEFT  
LABEL, CHAR, ISCRUB 24, RIGHT  
LABEL, CHAR, ISCRUB 26C,  
RIGHT  
LABEL, PANEL, RIGHT  
LABEL, PANEL, LEFT  
2B  
3
4
5
6
86318600  
86317040  
86017030  
86243990  
86004970  
-
-
-
1
1
1
1
1
500780  
50990  
LABEL, COVER PANEL  
LABEL, WINDSOR LOGO DOMED  
86317500 CHARIOT SCRUBBER 11/15/08  
5-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FRAME-LOWER  
18  
5
20  
10  
2
2
16A  
16B  
11  
15  
12  
10  
3
2
2
7
17  
11  
3
21  
5
19  
8
2
22  
5
13  
2
2
6
12  
15  
1
14  
4
9
86317500 CHARIOT SCRUBBER 11/15/08  
5-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FRAME - LOWER  
SERIAL NO.  
FROM  
REF PART NO. PRV NO. QTY  
DESCRIPTION  
NOTES  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
86091420  
86270830  
86197040  
86271870  
86276070  
86276950  
86088750  
86088760  
86010630  
86010670  
86279130  
86064300  
86071120  
86079290  
86079320  
05251  
57023  
57264  
57290  
70593  
70772  
75457  
75458  
87013  
87029  
87083  
140790  
140811  
620097  
620101  
-
1
24  
4
4
20  
4
1
1
4
6
4
2
1
2
2
1
1
1
AXLE, REAR, WELDMENT  
NUT, 5/16-18 HEX NYLOCK SS  
NUT, 5/16-18 HEX ACORN  
NUT, 1/4-20 HEX NYLOCK THIN SS  
SCR, 5/16-18 X 3/4 CARRIAGE SS  
SCR, 1/4-20 X 3/4 CARRIAGE SS  
TRAY, SLIDE, RIGHT  
TRAY, SLIDE, LEFT  
WASHER, 1/4 X 5/8 FLAT SS  
WASHER, 5/16 X 3/4 SS  
WASHER, 5/16 SPLIT  
PAD, TIPPING BAR  
BRKT, BRACE, RIGHT REAR  
PLATE, REAR COVER ADJ.  
PLATE, PAD RETAINER  
BRKT, BRACE, LT. REAR SOL.  
BRKT BRACE, LT REAR  
FRAME, MAIN  
16A 86303720  
16B 86071130  
DISK  
CYLINDRICAL  
140812  
-
17  
18  
19  
20  
21  
22  
86314900  
86314960  
86314970  
86314980  
86314990  
86315210  
-
-
-
-
1
1
1
1
BRKT, LINKAGE, LEFT  
BRKT, LINKAGE, RIGHT  
BRKT, BRACE, LEFT FRONT  
BRKT, BRACE, RIGHT FRONT  
BRKT, STRAINER  
-
1
86317500 CHARIOT SCRUBBER 11/15/08  
5-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FRAME-UPPER  
2
3
4
2
3
5
6
2
2
7
1
2
86317500 CHARIOT SCRUBBER 11/15/08  
5-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FRAME-UPPER  
SERIAL NO.  
FROM  
REF  
1
2
3
4
5
6
7
PART NO.  
86074160  
86270830  
86276070  
86314760  
86073500  
86314770  
86277460  
PRV NO. QTY  
DESCRIPTION  
BRKT, SIDE CHANNEL R  
NUT, 5-16-18 HEX NYLOCK SS  
SCR, 5-16-18 X 3/4 CARRIAGE SS  
TRAY, CABLE  
BRKT, SIDE CHANNEL L  
BRKT, STEERING SUPPORT  
SCR, 5/16-18 X 5/8 BSHCS SS  
NOTES:  
270101  
57023  
70593  
-
1
10  
12  
1
270090  
-
1
2
70847  
1
86317500 CHARIOT SCRUBBER 11/15/08  
5-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PEDAL PLATFORM  
21  
9
18  
19  
8
16  
17  
25  
2
1
22  
15  
3
14  
6
4
24  
10  
22  
15  
5
26  
13  
12  
28  
23  
11  
27  
20  
11  
7
86317500 CHARIOT SCRUBBER 11/15/08  
5-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PEDAL PLATFORM  
SERIAL  
REF  
PART NO.  
PRV NO. QTY  
DESCRIPTION  
NO.  
NOTES  
FROM  
1
2
3
4
5
6
7
8
86233170  
86264920  
86222510  
86221850  
86136310  
86312820  
86288720  
86272040  
86223260  
86223580  
86274340  
86278060  
86277360  
86277370  
86277380  
86277390  
86312770  
86007110  
86224750  
86279140  
86279720  
86279730  
86224360  
86224350  
86216380  
86222780  
86222810  
86254970  
20054  
27049  
34430  
34433  
57086  
-
57277  
57503  
66085  
67502  
70179  
70759  
70833  
70834  
70835  
70836  
-
72123  
73993  
87085  
87248  
87249  
730325  
730305  
140713  
620047  
620050  
730304  
2
1
1
1
1
1
1
2
1
1
7
2
1
1
4
2
1
1
1
6
2
4
1
1
2
1
1
1
CLAMP, 3/8 NYLON UL/CSA  
CABLE TIE, .19 X 7 UL/CSA  
PEDAL, THROTTLE  
LINK, THROTTLE  
NUT, M5 HEX  
BRACKET, POT, SPEED  
NUT, M6 NYLOCK PLATED  
NUT, M3.5 X 2.8 HEX  
PLUNGER, PLATFORM SWITCH  
ROD, PIVOT, 8.5MM X 77  
SCR, M6 X 16 PH  
SET SCR, M4 X 4MM NP  
SCR, M6 X 10 PH  
SCR, M5 X 30 SHCS  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
SCR, M4.8 X 16 PHTF  
SCR, M3.5 X 38 PH  
PLATFORM  
SWITCH, 25A SPST 125-250V SNAP  
SPRING, COMP, .48OD X .91L  
WASHER,M6 SPLIT LOCK DIN127B  
WASHER, M4 INT STAR  
WASHER, M5 INT STAR  
SPACER 12.7MMOD X 2.78W X 6L  
SPACER, 8MM X 16LG  
BUSHING, 8MM X 10 LG CLY  
PLATE, PIVOT  
PLATE, COVER  
SPRING, COMP 18MM OD X 83 X 2  
NOTE: Complete platform assembly is available, Part No. 86313640  
86317500 CHARIOT SCRUBBER 11/15/08  
5-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PEDAL PLATFORM  
2
3
13  
15  
6
11  
14  
6
12  
10  
9
7
1
4
8
5
8
5
86317500 CHARIOT SCRUBBER 11/15/08  
5-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PEDAL PLATFORM  
SERIAL NO.  
REF PART NO. PRV NO. QTY  
DESCRIPTION  
COTTER, 1/2” RING  
SCR, 5/16-18 X 1.5 HHCS GR5PLT  
CABLE TIE, 7” UL/CSA  
BUMPER, 1 X 1.375 RUBBER  
WASHER, 5/16 FLAT SS  
M12 FLAT WASHER  
WASHER, 7/16ID X1D.08 FLT SS  
NUT, 5/16-18 HEX NYLOCK SS  
STUB AXLE, M12-1.75 X 45MM  
WASHER, .506 ID X .94D X .064 NYL  
PIN, CLEVIS 1/2 X 2.25  
FROM  
NOTES:  
1
2
86008680  
86274690  
86264920  
86231070  
86010670  
86259430  
86010770  
86270830  
86256470  
86278850  
86248920  
86064480  
86271190  
86007780  
86259440  
80607  
70258  
27049  
730328  
87029  
87485  
87143  
57023  
70852  
80613  
66487  
629993  
57142  
73576  
87486  
1
2
3
2
5
4
2
4
2
2
1
1
2
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
PLATE, SWITCH BASE  
NUT, M12 X 1.75 HEX DIN934 PLT  
SPRING, COMP .60D X2.0L X .045W  
WASHER, M12 SPRING LOCK  
86317500 CHARIOT SCRUBBER 11/15/08  
5-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REAR COVER  
12  
11  
9
13  
1
10  
14  
2
3
2
9
8
15  
3
16  
7
6
4
5
86317500 CHARIOT SCRUBBER 11/15/08  
5-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REAR COVER  
SERIAL NO.  
FROM  
REF  
1
2
3
4
5
6
7
8
PART NO.  
86276780  
86279130  
86010670  
86031780  
86005860  
86228980  
86275870  
86242140  
86010770  
86248380  
86005630  
86071030  
86010780  
86271940  
86006560  
86066940  
PRV NO.  
70728  
87083  
87029  
270082  
57273  
09152  
70556  
72193  
87143  
66433  
57022  
140786  
87162  
57299  
70083  
140891  
QTY  
3
5
5
1
2
2
2
1
2
1
1
1
2
2
2
1
DESCRIPTION  
SCR, 5/16-18 X 3/4 HHCS SS  
WASHER, 5/16 SPLIT LOCK PLTD  
WASHER, 5/16 FLAT SS  
NOTES:  
COVER, REAR, DELUXE  
NUT, 1/4-20 X 12MM HEX BARREL  
BEARING FLANGED .377ID X .505OD  
SCR, 1/4-20 X 1.5” PPHMS SS  
KNOB, 3/8-16 X 1.5  
WASHER, 7/16ID X 1D X .08FLT SS  
PAD, FLAT LEANING  
NUT, 3/8-16 HEX NYLOCK THIN SS  
BRKT, ASSEMBLY, REAR COVER  
WASHER, 1/4 SPLIT LOCK  
NUT, 1/4-20 ACORN SS  
SCR, 5/16-18 X 1 HHCS SS  
BAR, COVER  
9
10  
11  
12  
13  
14  
15  
16  
86317500 CHARIOT SCRUBBER 11/15/08  
5-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB BRUSH/PAD DRIVER-DISK  
7
5
6
9
4
8
7
5
6
9
4
8
2A  
2B  
2C  
2D  
1
5
3
86317500 CHARIOT SCRUBBER 11/15/08  
5-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB BRUSH/PAD DRIVER-DISK  
SERIAL NO.  
REF  
1
PART NO.  
86000170  
86000180  
86000190  
86000200  
86283820  
86005070  
86276590  
86276580  
86276600  
86007910  
86007280  
86005940  
PRV NO. QTY  
DESCRIPTION  
PAD DRIVER, 12” SD  
BRUSH, 12” POLYPROPYLENE SD  
BRUSH, 12” NYLON SD  
BRUSH, 12” MILD GRIT SD  
BRUSH, 12” SUPER AGG SD  
LOCK, PAD CENTER SNAP, TWO STEP  
SCR, #12 X 1 PPHSMS SS  
FROM  
NOTES:  
02400  
02401  
02402  
02404  
02405  
51284  
70695  
70694  
70696  
73817  
730011  
62852  
2
2
2
2
2
1
3
1
3
1
1
1
2A  
2B  
2C  
2D  
3
4
5
6
7
SCR, 8-32 X 3/4 PTHMS  
SCR, #10 X 3/4 PTHSMS SS  
SPRING, EXT .31 D X 2.0 L X .03 W SS  
SOCKET, DRIVE BRUSH  
8
9
PLATE, BRUSH RELEASE  
86317500 CHARIOT SCRUBBER 11/15/08  
5-20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB BRUSH/PAD-CYLINDRICAL  
86317500 CHARIOT SCRUBBER 11/15/08  
5-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB BRUSH/PAD-CYLINDRICAL  
SERIAL NO.  
REF  
1
PART NO.  
41150040  
74010050  
51128230  
50052670  
73430370  
63693890  
63694540  
63694550  
63694560  
69069350  
69069810  
69069820  
PRV NO. QTY  
DESCRIPTION  
WASHER CLOSURE  
FROM  
NOTES:  
-
-
-
-
-
-
-
-
-
-
-
-
1
1
1
1
1
-
2
BALL BEARING 6302-2RS-DIN6  
BRUSH TORX  
3
4
RONDE  
5
LOCKING RING 50X2-FST-RF DIN 471  
105MM WHITE PAD  
6A  
6B  
6C  
6D  
7A  
7B  
7C  
-
PAD YELLOW 105 20 PCS  
PAD GREEN 20PS  
-
-
PAD RED 105 20 PCS  
-
ROLLER BRUSH RED-BR 65  
ROLLER BRUSH WHITE-BR 65  
ROLLER BRUSH ORANGE-BR 65  
-
-
7D  
7E  
8
69069830  
69069840  
47624320  
-
-
-
-
-
-
ROLLER BRUSH GREEN-BR 65  
ROLLER BRUSH BLACK-BR 65  
ROLL PAD BR 65  
86317500 CHARIOT SCRUBBER 11/15/08  
5-22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB DECK – DISK  
20  
19  
19  
1
20  
2
8
18  
3
FROM  
PUMP  
4
8
17  
5
16  
15  
6
8
9
7
14  
10  
11  
12  
13  
86317500 CHARIOT SCRUBBER 11/15/08  
5-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB DECK-DISK  
SERIAL  
REF PART NO. PRV NO. QTY  
DESCRIPTION  
NO.  
NOTES:  
FROM  
1
2
3
-
4
5
6
7
8
86281100  
86003580  
86005490  
86216200  
86004810  
86093990  
86010790  
86276970  
86264920  
39274  
34327  
53808  
14739  
48040  
730330  
87163  
70774  
27049  
1
1
2
-
2
1
8
8
6
HOSE, 1/2ID WIRE BOUND X 8”  
FITTING, 1/2”X3/8”X3/8” RED  
MOTOR ASM, 36VDC300RPM GEAR  
BRUSH SET MOTOR 53808  
KEY, 1/4 SQ X 1.00  
SCRUBDECK, 24IN  
WASHER, 3/8 SPLIT LOCK PLTD  
SCR, 3/8-16 X 3/4 HHCS SS  
CABLE TIE, 7” UL/CSA  
VALVE, SOLENOID, 36VDC, 1/2  
BARB  
9
86010600  
84199  
1
-
-
86003460  
86136820  
86003420  
86279630  
86279130  
86007020  
86279530  
86271830  
86233150  
86001550  
86281310  
86002830  
86264940  
29260  
47395  
29220  
87212  
87083  
70673  
87173  
57283  
20042  
40043  
39326  
27196  
27051  
-
-
DIAPHRAGM, SRVC PART SLND  
SERVICE SLND SPRG KIT  
DRIVER, BRUSH SD  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
2
2
2
2
2
2
1
2
2
2
2
WASHER, .344IDX1.130DX.09T PLT  
WASHER, 5/16 SPLIT LOCK PLTD  
SCR, 5/16-18 X 1.25 HHCS SS NP  
WASHER, .765IDX1.310DX.09T SS  
NUT, 3/8 NPT PLASTIC  
CLAMP, 3/8 HOSE (D-SLOT)  
HOSEBARB, 3/8MPT X 3/8 90D  
HOSE, 3/8ID WIREBOUND X 8”  
CABLE TIE, .375 X 24.7  
CABLE TIE, 11.38” UL/CSA  
86317500 CHARIOT SCRUBBER 11/15/08  
5-24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB DECK-CYLINDRICAL  
86217500 CHARIOT SCRUBBER 11/15/08  
5-25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB DECK-CYLINDRICAL  
SERIAL  
NO.  
FROM  
PART  
NO.  
PRV  
NO.  
REF  
QTY  
DESCRIPTION  
NOTES:  
1
2
3
4
5
6
7
8
9
50448660  
73060310  
73120260  
73130030  
50448580  
50560100  
51005530  
73180020  
73430150  
51163400  
-
-
-
-
-
-
-
-
-
-
2
10  
10  
10  
2
2
2
2
2
RETAINER PLATE TRANSMISSION  
SCREW M 6X16-A2-70 DIN 7984  
WASHER 6-A2 ISO 7090  
SPRING WASHER B 6FST-A3E DIN 127  
HOLDER-UP  
ROCKER BR-VS  
DRIVESHAFT BR 65/90  
PARALLEL KEY 5X5X16-C45R DIN 6885-1  
LOCKING RING 15X1-FST-RF DIN 471  
BOLT HOLDER-UP  
10  
2
COUNTERSUNK SCREW M8X16-A2-70  
ISO 10642  
11  
73056370  
-
2
12  
13  
14  
15  
16  
17  
51163540  
56254830  
63431490  
63484420  
63631580  
50332060  
-
-
-
-
-
-
2
2
2
2
2
4
BRUSH TRANSMISSION BR  
BELT PULLEY 57MM  
QUICK-FASTENER  
RIBBED V-BELT  
JOINT RING NILOSRING  
LOCKING PART  
BALL BEARING 6002-2RS-WAELZLAGST  
DIN 62  
18  
74011150  
-
4
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
-
73432310  
73030470  
50333940  
50332410  
73030370  
50332420  
50334030  
55150960  
53830970  
50615800  
50707530  
51902610  
46239200  
66102160  
66130250  
53948230  
50448670  
50094010  
5009420  
51163390  
50332400  
63304070  
63908920  
66463290  
66463300  
73031070  
66469790  
63884820  
63211960  
27630040  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
2
5
2
1
28  
1
1
2
1
1
1
1
2
1
2
2
2
1
1
2
2
2
1
2
2
3
4
1
1
-
LOCKING RING 32X1,2-ST-PH DIN 472  
SCREW M6X16-ST-R3R (IN6RD)  
LOCKING PART  
COVERING CAP LEFT  
SCREW M5X10-ST-P2R (IN6RD)  
COVERING CAP RIGHT  
COVER PLATE  
ROLLER  
DECAL  
BRUSH HOUSING BR 65  
TANK REFUSE 65  
STRIP WATER DISTRIBUTOR  
MOTOR COMPLETE 24V/600W  
CARBON BRUSHES  
BLOWER WHEEL  
SPLASH GUARD  
RETAINER STRIP SPLASH GUARD  
BRACKET RIGHT SCRAPER LIP  
BRACKET LEFT SCRAPER LIP  
THREADED BOLT  
HAND WHEEL  
SPRING CLIP  
SPIRAL HOSE  
RED PLUG  
BLUE PLUG  
SCREW 5X16-10.9-P2R (K-IN6RD)  
SWITCH CONTACT  
HOSE COUPLING  
STAR GRIP M5X10  
BRUSH HEAD R 65 CM W/SIDE  
DECK,COMPLETE  
86217500 CHARIOT SCRUBBER 11/15/08  
5-26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB DECK MOUNTING-CYLINDRICAL  
1
2
8
3
4
5
6
7
9
86217500 CHARIOT SCRUBBER 11/15/08  
5-27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB DECK MOUNTING-CYLINDRICAL  
SERIAL NO.  
REF  
1
2
3
4
5
6
7
8
PART NO.  
86315230  
86274660  
86224370  
86008460  
86009050  
86010770  
86005630  
86314850  
86314840  
PRV NO. QTY  
DESCRIPTION  
PIN, BALL LOCK  
FROM  
NOTES:  
-
1
2
2
2
2
2
2
1
1
70255  
730335  
80102  
81324  
87143  
57022  
-
SCR, 3/8-16 X 1.5 HHCS GR5 PLT  
SPACER, 1 OD X .391 ID X .500  
SPACER, .500OD X .391ID X .400  
BEARING, 1/2 ID X 11/32L NYLON  
WASHER, #6 LOCK  
NUT, 3/8-16 HEX NYLOCK THIN SS  
ARM ASSY, DECK, RIGHT  
ARM ASSY, DECK, LEFT  
-
9
86317500 CHARIOT SCRUBBER 11/15/08  
5-28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB DECK LIFT-DISK  
10  
SEE DETAIL 'A'  
6
13  
11  
14  
9
12  
15  
16  
17  
18  
7
5
4
3
19  
22  
23  
16  
29  
19  
20  
21  
28  
24  
27  
26  
1
21  
2
20  
DETAIL 'A'  
22  
19  
16  
8
25  
86317500 CHARIOT SCRUBBER 11/15/08  
5-29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB DECK LIFT-DISK  
SERIAL NO.  
REF PART NO. PRV NO. QTY  
DESCRIPTION  
SCR, 3/8-16 X 1 HHCS SS NP  
BALL JOINT ASY, 3/8-24 RH  
SCR, 1/4-20 X 2 HHCS  
WASHER, 1/4 SPILT LOCK PLTD  
PLATE, ACTUATOR SPR, SCRUBDECK  
BRKT, ACTUATOR MTG, SCRUBBER  
SCR, 1/4-20 X 1/2 SHCS  
FROM  
NOTES:  
1
2
3
4
5
86276920  
86008810  
86273850  
86010780  
86079030  
70755  
80697  
70022  
87162  
620058  
2
2
2
2
1
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
86091760  
86274110  
86005830  
86008660  
86277030  
86224370  
86270830  
86272460  
86011950  
86275510  
86010770  
86070810  
140741  
70094  
57263  
80605  
70780  
730335  
57023  
66268  
-
1
2
2
1
2
2
2
1
1
2
6
1
NUT, 3/8-24 UNF LH  
COTTER, 5/16” RING  
SCR, 5/16-18 X 1.25 CARRIAGE SS  
SPACER, 1 OD X .391 ID X .500  
NUT, 5/16-18 HEX NYLOCK SS  
PIN, CLEVIS 5/16 X 3.00 PLTD  
ACTUATOR, 36VDC 3.5 STRK  
SCR, 3/8-16 X 4.5” HHCS GR5  
WASHER, 7/16ID X IDX.08 FLT SS  
BRKT, ACTUATOR SPGS, SCRUBDECK  
SPRING COMP .96D X 4.0L X .135W  
NUT, 3/8-16 HEX NYLOCK THIN SS  
NUT, 3/8-24 HEX NYLOCK  
BEARING, 1/2 ID X 11/32L NYLON  
SPACER, .500OD X .391ID C .400  
SPACER, 1 OD X 0.391 ID X 1.063  
SCR, 3/8-16 X 2 HHCS  
BALL JOINT ASSY, 3/8-24 LH  
LINKAGE, .25 X 1.25 X 9.25  
ROD, SCRUB LIFT  
70494  
87143  
140739  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
86255450  
86005630  
86271530  
86009050  
86008460  
86224380  
86274010  
86001320  
86077330  
86223540  
86005800  
86005810  
81376  
57022  
57216  
81324  
80102  
730336  
70070  
140353  
31373  
66483  
57217  
57245  
2
8
4
4
4
2
2
2
2
2
2
2
NUT, 3/8-24 HEX JAM  
NUT, 1/4-20 HEX NYLOCK SS  
86317500 CHARIOT SCRUBBER 11/15/08  
5-30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB DECK ACTUATOR-CYLINDRICAL  
16  
19  
18  
17  
23  
16  
19  
18  
17  
23  
14  
17  
26  
2
28  
9
17  
20  
26  
10 13  
5
22  
3
21  
17  
4
12  
28  
1
18  
17  
6
7
27  
28  
8
1
2
24  
11  
27  
15  
18  
21  
25  
86317500 CHARIOT SCRUBBER 11/15/08  
5-31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB DECK ACTUATOR-CYLINDRICAL  
PRV  
NO.  
-
-
-
-
-
-
SERIAL NO.  
REF PART NO.  
QTY  
DESCRIPTION  
SPACER, .498 X.313 X.500  
PULLEY, 2 IN.  
ACTUATOR, 36VDC, 4.5" STROKE  
SPACER  
BRKT ASSY, ACTUATOR  
YOKE, CABLE  
GUARD, PULLEY  
FROM  
NOTES:  
1
86317340  
86317330  
86316550  
86315290  
86315260  
86315250  
86315240  
86270770  
86315150  
86315140  
86315120  
86315110  
86315090  
86314810  
86273740  
86224380  
86010780  
86010670  
86231090  
86006980  
86136850  
86274460  
86273920  
86273820  
86273780  
86273750  
86005810  
86270990  
3
3
1
1
1
1
1
1
1
1
1
2
1
1
1
2
16  
6
2
1
3
1
2
1
1
12  
2
4
2
3
4
5
6
7
8
9
-
57006  
-
NUT, 1/4-20 HEX  
PLATE, PULLEY, REAR  
PLATE, PULLEY, FRONT  
SPRING, EXTENSION  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
-
-
-
-
BRKT, DECK PIVOT  
BELLCRANK ASSY, DECK  
CABLE ASSY, DECK LIFT  
SCR, 1/4-20 X 1-5 HHCS SS  
SPACER, 1 OD X .391 ID X 1.063  
WASHER, 1/4 SPLIT  
WASHER, 5/16 X 3/4 SS  
BUMPER, RUBBER 5/16" ID X 1.50  
SCR, 10-32 X 1/2 HHCS SS  
SHOULDER BOLT, 5/16 OD X 5/8 L  
SCR, 1/4-20 X 3/8 HHCS  
SCR, 1/4-20 X 1.75 PPHMS SS  
SCR, 1/4-20 X 1.25 HHCS SS  
SCR, 1/4-20 X 3/4 HHCS SS  
SCR, 1/4-20 X 5/8 HHCS SS  
NUT, 1/4-20 HEX NYLOCK SS  
NUT, 10-32 HEX NYLOCK SS  
-
70010  
730336  
87162  
87029  
80809  
70591  
70241  
70205  
70049  
70019  
70015  
70011  
57245  
57090  
86317500 CHARIOT SCRUBBER 11/15/08  
5-32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB DECK SKIRTS-DISK  
1
2
3
6
4
5
20  
5
21  
8
7
9
10  
19  
24  
11  
18  
12  
5
23  
22  
17  
16  
15  
7
14  
13  
86317500 CHARIOT SCRUBBER 11/15/08  
5-33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB DECK SKIRTS-DISK  
SERIAL NO.  
REF PART NO.  
PRV NO. QTY  
DESCRIPTION  
FROM  
NOTES:  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
86270830  
86070960  
86276070  
86228900  
86005810  
86276330  
86276950  
86277410  
86271950  
86079130  
86007650  
86007070  
86066460  
86001560  
86091770  
86001700  
86066480  
86091780  
86001570  
86066470  
86277500  
86271870  
86026470  
86026460  
57023  
140773  
70593  
09138  
57245  
70634  
70772  
70840  
57300  
620068  
730329  
70849  
140769  
140754  
140765  
140780  
140781  
140766  
140755  
140770  
70853  
57290  
47459  
47458  
4
2
4
2
6
2
8
6
6
4
4
6
1
1
1
1
1
1
1
1
3
3
-
NUT, 5/16-18 HEX NYLOCK SS  
BRKT, SKIRT STOP, SCRUBDECK  
SCR, 5/16-18 X 3/4 CARRIAGE SS  
BEARING FLANGED, .252IDX.503OD  
NUT, 1/4-20 HEX NYLOCK SS  
SCR, 1/4-20 X 1.25 CARRIAGE BZ  
SCR, 1/4-20 X 3/4 CARRIAGE SS  
SCR, 5/16-18 X 5/8 CARRIAGE SS  
NUT, 5/16-18 X 1 COUPLING SS  
PLATE, SKIRT, SPACER  
SPACER, .438D X .317ID X .25L  
SCR, 5/16-18 X 1.00 PTMS SS  
BAND, SKIRT, LEFT  
BLADE, SKIRT, SCRBDCK, 24IN LFT  
BRKT, SKIRT SCRUBDECK, LEFT  
BLADE, SKIRT, SCRUBDECK, FRONT  
BAND, SKIRT, SCRUBECK, FRONT  
BRKT, SKIRT, SCRUBDECK, RIGHT  
BLADE, SKIRT, SCRBDCK, 24IN RGT  
BAND, SKIRT, RIGHT  
SCR, 1/4-20 X 5/8 CARR SS  
NUT, 1/4-20 HEX NYLOCK THIN SS  
KIT, SKIRT LEFT  
SERVICE ONLY  
SERVICE ONLY  
-
KIT, SKIRT RIGHT  
86317500 CHARIOT SCRUBBER 11/15/08  
5-34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB DECK AQUA-MIZER™  
16  
15  
1
14  
2
13  
17  
6
4
5A  
5B  
3
7
8
9
3
12  
11A  
11B  
10  
18  
9
86317500 CHARIOT SCRUBBER 11/15/08  
5-35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCRUB DECK AQUA-MIZER™  
SERIAL NO.  
REF PART NO. PRV NO. QTY  
DESCRIPTION  
NOTES:  
FROM  
1
2
86270830  
86277050  
86276950  
86066430  
86001540  
86283550  
86071000  
86219690  
86277230  
86005810  
86070990  
86001520  
86283560  
86066420  
86272540  
86091800  
86008670  
86091790  
86024990  
86025000  
57023  
70782  
4
2
9
1
1
1
1
2
2
9
1
1
1
1
2
1
2
1
-
NUT, 5/16-18 HEX NYLOCK SS  
SCR, 5/16-18 X 3/4 SHCS  
3
70772  
SCR, 1/4-20 X 3/4 CARRIAGE SS  
BAND, RIGHT AQUAMIZER  
4
140747  
140753  
140939  
140779  
48080  
5A  
5B  
6
BLADE, AQUAMIZER, 12IN RGT  
BLADE, AQMZR 12 RT URETHANE  
BRKT, AQUAMIZER BLADE, RGT  
KNOB, 1.5 OD X 5/16-18  
7
8
70815  
SCR, 5/16-18 X 2.25 BSHCS SS  
NUT, 1/4-20 HEX NYLOCK SS  
BRKT, AQUAMIZER BLADE, LEFT  
BLADE, AQUAMIZER, 12IN LEFT  
BLADE, AQMZR 12 LT URETHATNE  
BAND, LEFT AQUAMIZER  
9
57245  
10  
11A  
11B  
12  
13  
14  
15  
16  
17  
18  
140778  
140752  
140940  
140746  
66465  
PIN, CLEVIS, 3/8 X 6.12, PLTD  
BRKT, AQUAMIZER MTG, LEFT  
COTTER, 3/8” RING  
140776  
80606  
140774  
47456  
BAND, LEFT AQUAMIZER  
AQUAMIZER RIGHT ASM. CHARIOT  
AQUAMIZER LEFT ASM. CHARIOT  
47457  
-
86317500 CHARIOT SCRUBBER 11/15/08  
5-36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SOLUTION-DISK  
5
28  
7
12  
TO  
SOLENOID  
8
34  
6
28  
23  
24  
19  
TO  
9
11  
TANK  
22  
21  
5
5
10  
25  
1
30  
29  
3
32  
31  
2
33  
26  
27  
5
13  
14  
15  
20  
18  
5
16  
4
20  
17  
86317500 CHARIOT SCRUBBER 11/15/08  
5-37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SOLUTION-DISK  
PART  
NO.  
PRV  
NO.  
SERIAL NO.  
FROM  
REF  
1
2
3
4
5
6
7
8
QTY  
1
1
1
1
5
4
1
1
1
1
1
1
1
1
1
1
1
-
DESCRIPTION  
NUT, 8/32 ACORN CAP, PLATED  
1” HOSE BARB X 3/4” GHT NYLON  
CAP, 3/4” GHT W/.17 HOLE  
ELBOW, 3/8 FPT PVC SCH 80  
CLAMP, 3/8 HOSE (D-SLOT)  
NUT, 10-32 HEX NYLOCK SS  
HOSE, 1/2ID WIRE BOUND X 40”  
TEE, 3/4 FPT  
HOSEBARB, 3/4 MPT X 1/2 90D  
HOSE, 1/2ID WIRE BOUND X 13”  
NIPPLE, 3/4 CLOSE PVCE  
HOSEBARB, 3/4 MPTX1, HOSE 90DEG  
HOSEBARB, 3/8 MPT X 1/2 DL  
VALVE, 3/8” FPT BALL  
NOTES:  
86248010  
86226950  
86073960  
86235450  
86233150  
86270990  
86281940  
86198050  
86240390  
86282190  
86247760  
86240600  
86197540  
86225680  
86197420  
86001590  
86007940  
86005870  
86136800  
86281950  
86315510  
86264920  
86274410  
57312  
40109  
22104  
31068  
20042  
57090  
39540  
81923  
40075  
39616  
80960  
41526  
40013  
84201  
31026  
40049  
73836  
59021  
73839  
39541  
-
9
10  
11  
12  
13  
14  
15  
16  
17  
-
ELBOW, 3/8 NPT STREET  
HOSEBARB, 3/8 MPT X 1/2 NYLON  
STRAINER, DEEP, 100 MESH  
O-RING, FILTER SEAL RON-VIK  
SCREEN, 100 MESH STRAINER DEEP  
HOSE, 1/2ID WIRE BOUND X 32”  
HOSE, 1 X 40 DRAIN  
CABLE, TIE. 7” UL/CSA  
SCR, 10-32 X 1.25 PPHMS SS  
BRKT, SOLUTION PUMP  
-
-
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
1
1
3
4
1
4
1
1
1
1
2
1
1
1
1
1
1
27049  
70195  
86070690 140724  
86010650  
86006100  
86271820  
86279130  
86276780  
86197940  
86246090  
87018  
65176  
57270  
87083  
70728  
40027  
51461  
WASHER, #10 X 9/16 OD  
PUMP ASM, 36V  
NUT, 5/16-18 CAPTIVE “J” PLTD  
WASHER, 5/16 SPLIT LOCK PLTD  
SCR, 5/16-18 X 3/4 HHCS SS  
HOSEBARB, 3/8MPTX1/2 90D DL  
LANYARD, .093 X 6”, LOOP - .26 EYE  
SPACER, .17 ID X .25 OD X 3/16 LG  
WASHER, 1.0 D X .1 THK, SEAL  
SCR, 8-32 X 1/2 BHCS SST  
CLAMP, 1.0” WORM GEAR  
86254320 730400  
86259450  
86252730  
86233110  
86233300  
87507  
70887  
20018  
20101  
CLAMP, 1.25” WORM GEAR SS  
86317500 CHARIOT SCRUBBER 11/15/08  
5-38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SOLUTION-CYLINDRICAL  
5
28  
7
28  
TO  
SOLENOID  
6
24  
23  
5
22  
21  
25  
12  
8
33  
19  
TO  
TANK  
9
11  
1
5
34  
36  
10  
18  
4
5
35  
20  
38  
30  
37  
29  
2
27  
32  
31  
17  
26  
13  
3
5
14  
16  
15  
86317500 CHARIOT SCRUBBER 11/15/08  
5-39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SOLUTION-CYLINDRICAL  
SERIAL  
NOTES:  
NO.  
REF PART NO.  
PRV NO. QTY  
DESCRIPTION  
1
2
3
4
5
6
7
8
9
86270830  
86001530  
86188210 11-800354  
57023  
40039  
2
1
1
1
5
4
1
1
1
1
1
NUT, 5/16-18 HEX NYLOCK SS  
HOSE BARB, 1/2 MPT X 1/2 HOSE 90  
NIP, 1/2 X 3/8 HEX BR  
86248010  
86233150  
86270990  
86282320  
86198050  
86240390  
86280910  
86247760  
57312  
20042  
57090  
39710  
81923  
40075  
39174  
80960  
NUT, 8/32 ACORN CAP, PLATED  
CLAMP, 3/8 HOSE (D-SLOT)  
NUT, 10-32 HEX NYLOCK SS  
HOSE, 1/2ID WIRE BOUND X 49”  
TEE, 3/4 FPT  
HOSEBARB, 3/4 MPT X 1/2 90D  
HOSE, 1/2ID WIRE BOUND X 23”  
NIPPLE, 3/4 CLOSE PVCE  
10  
11  
HOSEBARB, 3/4 MPTX1, HOSE  
90DEG  
12  
86240600  
41526  
1
13  
14  
15  
16  
17  
-
86233110  
86225680  
86197420  
86197540  
86256120  
86005870  
86136800  
86282370  
86315510  
86264920  
86274410  
86070690  
86010650  
86006100  
86271820  
86226950  
86073960  
86197940  
86246090  
86254320  
86259450  
86252730  
86233300  
86010600  
86174400  
86010780  
86276780  
86279130  
20018  
84201  
31026  
40013  
730368  
59021  
73839  
39735  
-
27049  
70195  
140724  
87018  
65176  
57270  
40109  
22104  
40027  
51461  
730400  
87507  
70887  
20101  
84141  
70194  
87162  
70728  
87083  
1
1
1
1
1
-
CLAMP, 1.00” WORM GEAR  
VALVE, 3/8” FPT BALL  
ELBOW, 3/8” NPT STREET  
HOSEBARB, 3/8 MPT X 1/2 DL  
STRAINER, 1/2 FPT 100 MESH  
O-RING, FILTER SEAL RON-VIK  
SCREEN, 80 MESH STRAINER DEEP  
HOSE, 1/2ID WIRE BOUND X 40”  
HOSE, DRAIN 1.0 X 110 CONV  
CABLE, TIE. 7” UL/CSA  
-
-
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
1
1
2
4
1
4
1
1
1
1
2
1
1
1
1
1
1
2
2
1
1
SCR, 10-32 X 1.25 PPHMS SS  
BRKT, SOLUTION PUMP  
WASHER, #10 X 9/16 OD  
PUMP ASM, 36V  
NUT, 5/16-18 CAPTIVE “J” PLTD  
1” HOSEBARB X 3/4” GHT NYLON  
CAP, 3/4” GHT W/.17 HOLE  
HOSEBARB, 3/8MPTX1/2 90D DL  
LANYARD, .093 X 6”, LOOP - .26 EYE  
SPACER, .17 ID X .25 OD X 3/16 LG  
WASHER, 1.0 D X .1 THK, SEAL  
SCR, 8-32 X 1/2 BHCS SST  
CLAMP, 1.25” WORM GEAR SS  
VALVE 24VDC SOL. 1/2 HOSEBARB  
SCR, 1/4-20 X 5/8 BHCS  
WASHER, 1/4 SPLIT LOCK PLTD  
SCR, 5/16-18 C 3/4 HHCS SS  
WASHER, 5/16 SPLIT LOCK PLTD  
86317500 CHARIOT SCRUBBER 11/15/08  
5-40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SQUEEGEE-DISK  
1
39  
2
38  
37  
3
9
4
36  
40  
35  
5
8
5
6
6
34  
7
8
5
33  
9
11  
7
10  
11  
15  
12  
13  
14  
15  
16  
17  
18  
19A  
19B  
20  
32  
30  
21  
29  
22  
25  
23  
24  
26  
31  
27A  
27B  
28  
86317500 CHARIOT SCRUBBER 11/15/08  
5-41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SQUEEGEE-DISK  
SERIAL NO.  
FROM  
REF  
1
2
3
4
5
6
7
8
PART NO.  
86004890  
86070920  
86006270  
86007780  
86005630  
86270830  
86010670  
86001350  
86011020  
86005650  
86276950  
86083290  
86276710  
86083250  
86271870  
86007040  
86271820  
86087830  
86001630  
86283540  
86083270  
86083260  
86277000  
86276990  
86277450  
86008390  
86083280  
86001580  
86283510  
86066440  
86006400  
86009170  
86009180  
86066450  
86009910  
86274130  
86071070  
86071060  
86009200  
86277440  
86008660  
86277460  
PRV NO. QTY  
DESCRIPTION  
KNOB, ALUM 3/8-16 NYLOCK NUT SS  
BRKT, SQG WHEEL  
NOTES:  
48095  
140759  
66276  
73576  
57022  
57023  
87029  
140390  
89202  
57031  
70772  
66463  
70717  
66459  
57290  
70680  
57270  
140760  
140764  
140938  
66461  
66460  
70777  
70776  
70846  
78493  
66462  
140763  
140935  
140761  
67380  
81488  
81489  
140762  
82576  
70098  
140795  
140794  
81535  
70845  
80605  
70847  
2
2
2
2
2
3
4
2
4
2
4
2
2
1
4
5
5
1
1
1
1
1
4
2
2
1
1
1
1
1
4
1
1
1
1
2
1
1
1
1
2
1
PIN, CLEVIS 5/16 X 1.63 PLTD  
SPRING, COMP .60D X 2.0L X .045 W  
NUT, 3/8-16 HEX NYLOCK THIN SS  
NUT, 5/16-18 HEX NYLOCK SS  
WASHER, 5/16 FLAT SS  
BUSHING, SPANNER .435 X 1.10  
WHEEL, 3” DIA CUSHION RUBBER  
NUT, 5/16-18 HEX  
SCR, 1/4-20 X 3/4 CARRIAGE SS  
PLATE, SQG WHEEL NMT BUMPER  
SCR, 5/16-18 X 2.0 CARRIAGE SS  
PLATE, SQG TOP 33”  
NUT, 1/4-20 HEX NYLOCK THIN SS  
SCR, 5/16-18 X 1 THUMB SS TYPE P  
NUT, 5/16-18 CAPTIVE “J” PLTD  
STRAP, SQUEEGEE  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19A  
19B  
20  
21  
22  
23  
24  
25  
26  
27A  
27B  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
BLADE, SQU, FRONT 36.7  
BLADE, SQU, FRONT 36.7 URETHANE  
PLATE, SQG VERICAL FILLER (F)  
PLATE, SQG BOTTOM 33”  
SCR, 1/4-20 X 1.5 CARRIAGE SS  
SCR, 3/8-16 X 3.5 CARRIAGE SS  
SCR, 3/8-16 X 2 LG CARRIAGE SS  
TUBE ASM, SQUEEGEE VAC  
PLATE, SQG VERTICAL FILLER  
BLADE, SQU, REAR 40.6 LINATEX  
BLADE, SQU, REAR 40.6 URETHANE  
BAND, REAR SQUEEGEE  
RIVET, 5/32 OF X 1/8 GRIP  
LATCH, SQUEEGEE STRAP  
STRIKER, SQUEEGEE STRAP REAR  
BAND, SQG REAR RH  
VIAL, LEVEL  
SCR, 8-32 X 3/8 PHTC ‘F’ PLATD  
BRKT, SQG QUICK CONNECT LOCK  
BRKT, SQG QUICK CONNECT MTG  
KNOB, 3/8-16 4 PRONG ALUM  
SCR, 3/8-15 X 2.5 LG BSHCS SS  
COTTER, 5/16 RING  
SCR, 5/16-18 X 5/8 BSHCS SS  
NOTE: Complete Squeegee Assembly available, Part No. 47455  
86317500 CHARIOT SCRUBBER 11/15/08  
5-42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SQUEEGEE-CYLINDRICAL  
86317500 CHARIOT SCRUBBER 11/15/08  
5-43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SQUEEGEE-CYLINDRICAL  
SERIAL NO.  
REF PART NO. PRV NO. QTY  
DESCRIPTION  
WASHER 8-00HV-A3E ISO 7090  
STAR GRIP VA  
SLEEVE SUCTION BAR IN VA  
DEFECTOR ROLL SUCTION BAR  
WASHER, M8 SPLIT LOCK  
SCR, M8X20 HHMS  
SUCTION NIPPLE  
NUT, 3/8-16 HEX NYLOCK THIN SS  
END PIECE RIGHT  
HEXAGON NUT M6-14305 ISO 10511  
WASHER 6-A2 ISO 7090  
HOLDER ROLLER  
WASHER, 5-A2 ISO 7090  
SCREW M5X10-ST-P2R (IN6RD)  
WHEEL D54  
FROM  
NOTES:  
1
2
73120040  
63212110  
50942310  
55152670  
86137310  
86274860  
50319890  
86005630  
50319910  
73114220  
73120260  
50443040  
73120580  
73030370  
64354010  
51052450  
-
-
2
2
2
2
2
2
1
1
1
2
4
2
4
4
2
2
3
-
4
-
5
87098  
6
70311  
7
-
8
57022  
9
-
-
-
-
-
-
-
-
10  
11  
12  
13  
14  
15  
16  
AXLE  
HEXAGONAL HEAD SCREW M 6X45-  
A4-70 ISO 4  
END PIECE LEFT  
SQUEEGEE BLADE SET OIL  
RESISTAND (890MM)  
SQUEEGEE BLADE SET STANDARD  
(890MM)  
17  
18  
73045500  
50319900  
-
-
-
2
1
1
19A 62732070  
19B 62732130  
19C 62732290  
-
-
1
1
SQUEEGEE BLADE SET ANTI  
STRIPE OIL RESISTAND (890MM)  
20  
21  
22  
23  
24  
25  
26  
47770590  
26395610  
51283390  
86009200  
86277440  
86314870  
86071070  
-
-
-
1
1
1
1
1
1
1
SQUEEGEE BAR CURVED  
ADD-ON KIT SUPPORT WHEELS  
ADDITON WEIGHT  
KNOB, 3/8-16 4 PRONG ALUM  
SCR, 3/8-16 X 2.50 LG BSHCS SSS  
BRKT, SQUEEGEE MTG  
81535  
70845  
-
140795  
BRKT, SQG QUICK CONNECT LOCK  
86317500 CHARIOT SCRUBBER 11/15/08  
5-44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SQUEEGEE LIFT-DISK  
1
2
15  
3
10  
20  
13  
13  
2
5
13  
25  
10  
12  
11  
10  
6
8
15  
9
7
26  
16  
16  
14  
27  
22  
17  
17  
13  
21  
19  
18  
24  
16  
16  
23  
4
10  
17  
13  
20  
86317500 CHARIOT SCRUBBER 11/15/08  
5-45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SQUEEGEE LIFT-DISK  
SERIAL NO.  
REF PART NO. PRV NO. QTY  
DESCRIPTION  
FROM  
NOTES:  
1
2
3
4
5
6
7
8
86068190  
86273820  
86000870  
86083490  
86068230  
86270870  
86002780  
86277410  
86075430  
86270830  
86276070  
86277400  
86010670  
86277460  
86271870  
86223370  
86231150  
86083440  
86276760  
86274720  
86071300  
86224290  
86071310  
86083500  
86271840  
86228880  
86277480  
140793  
70019  
05254  
66831  
140840  
57029  
270098  
70840  
270700  
57023  
70593  
70839  
87029  
70847  
57290  
66464  
09151  
66824  
70724  
70264  
140843  
730008  
140844  
66832  
57285  
09132  
70850  
1
1
1
1
1
3
1
4
1
9
3
2
10  
1
2
6
5
1
2
2
1
2
1
1
1
1
2
BRACKET, ACTUATOR MOUNT  
SCR, 1/4-20 X 1.25 HHCS  
ACTUATOR, 36VDC, 4.5” STROKE  
PLATE, PULLEY MOUNT, CORNER  
BRACKET, SQG LIFT PULLEY MOUNT  
NUT, 1/4-28 HEX SS  
CABLE, SQUEEGEE LIFT DELUXE  
SCR, 5/16-18 X 5/8 CARRIAGE SS  
COVER, SQUEEGEE LIFT  
NUT, 5/16-18 HEX NYLOCK SS  
SCR, 5/16-18 X 3/4 CARRIAGE SS  
SCR, 5/16-8 X 1.75 BSHCS SS  
WASHER, 5/16 FLAT SS  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
SCR, 5/16-18 X 5/8 BSHCS SS  
NUT, 1/4-20 HEX NYLOCK THIN SS  
PULLEY, PLASTIC 3.0 DIA  
BUSHING, FLANGE, .314ID X .502OD  
PLATE, PULLEY MOUNTING, CENTER  
SCR, 5/16-18 X 1.25 BSHCS SS  
SCR, 5/16-18 X 1.50 HHCS SS  
BRACKET, PULLEY RETAINER, DOUBLE  
SPACER, .317ID X .5OD X .44 LG  
BRKT, PULLEY RETAINER, DOUBLE  
PLATE, PULLEY RETAINER, CORNER  
NUT, 5/16-18 HEX NYLOCK THIN SS  
BEARING, .314 ID X .503 OD X 1  
SCR, 5/16-18 X 1/2 PTHMS SS  
86317500 CHARIOT SCRUBBER 11/15/08  
5-46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SQUEEGEE LIFT-CYLINDRICAL  
86317500 CHARIOT SCRUBBER 11/15/08  
5-47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SQUEEGEE LIFT-CYLINDRICAL  
SERIAL NO.  
REF PART NO. PRV NO. QTY  
DESCRIPTION  
ACTUATOR, 36VDC, 4.5" STROKE  
BRKT ASSY, ACTUATOR MOUNT  
YOKE, CABLE  
SQUEEGEE MOUNT ASSY  
CABLE ASSY, SQUEEGEE  
SCR, 1/4-20 X 1.5 HHCS SS  
SPACER, 1 OD X .391 ID X .500  
SPACER, .317ID X .5OD X .44LG  
WASHER, THRUST.51 ID X 1 ODBRO  
WASHER, 5/16 X 3/4 SS  
FROM  
NOTES:  
1
86316550  
86315270  
86315250  
86315000  
86314820  
86273740  
86224370  
86224290  
86259420  
86010670  
86008650  
86277480  
86276760  
86276690  
86007020  
86274720  
86273820  
86073600  
86083500  
86083490  
86083440  
86223370  
86272470  
86271870  
86005810  
86270990  
86270830  
86270770  
86231150  
86228840  
-
1
1
1
1
1
1
4
1
8
8
1
1
3
4
1
1
1
1
1
1
1
4
1
1
1
1
9
1
4
4
2
-
3
-
4
-
5
-
6
7
8
9
70010  
730335  
730008  
87232  
87029  
80604  
70850  
70724  
70715  
70673  
70264  
70019  
66833  
66832  
66831  
66824  
66464  
66270  
57290  
57245  
57090  
57023  
57006  
09151  
09124  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
COTTER, 1/4 RING  
SCR, 5/16-18X1/2 PTHMS SS  
SCR, 5/16-18 X 1.25 BSHCS SS  
SCR, 5/16-18 X 1.75 CARR SS  
SCR, 5/16-18 X 1.25 HHCS SS  
SCR, 5/16-18 X 1.50 HHCS SS  
SCR, 1/4-20 X 1.25 HHCS SS  
BRKT, PULLEY RETAINER, SINGLE  
PLATE, PULLEY RETAINER, CORNER  
PLATE, PULLEY MOUNT, CORNER  
PLATE, PULLEY MOUNTING, CENTER  
PULLEY,PLASTIC 3.0 DIA  
PIN, CLEVIS 3/16 X .75 PLTD  
NUT, 1/4-20 HEX NYLOCK THIN SS  
NUT, 1/4-20 HEX NYLOCK SS  
NUT, 10-32 HEX NYLOCK SS  
NUT, 5/16-18 HEX NYLOCK SS  
NUT, 1/4-20 HEX  
BEARING FLANGED .314IDX.502OD  
BEARING, FLANGED .313IDX.502OD  
86317500 CHARIOT SCRUBBER 11/15/08  
5-48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SQUEEGEE SWING  
1
1
24  
23  
22  
21  
6
2
20  
3
4
19  
18  
25  
5
6
16  
6
7
15  
17  
14  
7
13  
6
12  
11  
10  
6
9
8
86317500 CHARIOT SCRUBBER 11/15/08  
5-49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SQUEEGEE SWING  
SERIAL NO.  
REF  
1
PART NO.  
86276690  
86091530  
86090300  
86083370  
86091540  
86270830  
86271530  
86008810  
86271980  
86223590  
86001320  
86091810  
86224290  
86083400  
86276760  
86272630  
86008650  
86228840  
86277030  
86224380  
86083150  
86083310  
86226030  
86222580  
86070820  
PRV NO. QTY  
DESCRIPTION  
FROM  
NOTES:  
70715  
140787  
87247  
66475  
140800  
57023  
57216  
80697  
57303  
67510  
140353  
140798  
730008  
66479  
70724  
80771  
80604  
09124  
70780  
730336  
66446  
66468  
89268  
66466  
140740  
7
1
2
2
1
13  
2
1
1
1
1
1
2
1
2
1
1
4
4
4
2
1
2
2
1
SCR, 5/16-18 X 1.75 CARR SS  
BRACKET, SQUEEGEE SIDE PIVOT  
WASHER, 1.25 ID X .075 OCTAGON  
PLATE, SQG SWING SPACER  
BRACKET, H PIVOT MOUNT  
NUT, 5/16-18 HEX NYLOCK SS  
NUT, 3/8-24 HEX NYLOCK  
2
3
4
5
6
7
8
BALL JOINT ASY, 3/8-24 RH  
NUT, 3/8-24 WING SS  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
ROD, CAMBER ADJUST  
BALL JOINT ASSY, 3/8-24 LH  
BRKT, SQG QUICK CONNECT  
SPACER, .317ID X .500 X .44LG  
PLATE, CABLE RETAINING  
SCR, 5/16-18 X 1.25 BSHCS SS  
PIN, CLEVIS 1/4 X .88 PLTD  
COTTER, 1/4 RING  
BEARING, FLANGED .314 ID X .502 0D  
SCR, 5/16-18 X 1.25 CARRIAGE SS  
SPACER, 1 OD X .343 ID X 1.063  
PLATE, SQUEEGEE SWING  
PLATE, WHEEL RETAINER  
WHEEL, 1.000 OD X .323 ID X .750 SS  
PIN, .312 DIA X 1.250 LG SS  
BRKT, SQUEEGEE SWING HORIZ  
86317500 CHARIOT SCRUBBER 11/15/08  
5-50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEERING  
1
2
3
5
6
8
7
4
28  
9
10  
11  
12  
13  
27  
26  
25  
15  
14  
19  
24  
29  
23  
22  
20  
19  
21  
18  
16  
17  
30  
86317500 CHARIOT SCRUBBER 11/15/08  
5-51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEERING  
SERIAL NO.  
FROM  
REF PART NO.  
PRV NO. QTY  
DESCRIPTION  
NOTES:  
1
2
86271610  
86234810  
57228  
27945  
1
1
NUT, 5/8-16 HEX NYLOCK THN  
COVER, STEERING WHEEL  
INCLUDES  
27945  
3
86259610  
730117  
1
WHEEL, STEERING 40 SPLINE HUB  
4
5
6
7
8
9
86224050  
86228790  
86314830  
86005610  
86317090  
86219600  
86272900  
86224060  
86219650  
86228670  
86276070  
86224800  
86010670  
86135970  
86275190  
86008610  
86001030  
86224320  
86224810  
86005630  
86002750  
86278940  
86010780  
86274330  
86279130  
86253200  
86270830  
86232780  
730318  
09111  
-
57016  
-
1
1
2
1
1
1
1
1
1
1
2
2
2
1
1
2
1
1
1
1
1
2
1
1
2
1
2
-
SHAFT, UPPER STEERING  
BEARING, FLANGE .88ODX.75IDX.75  
BRKT, UPPER STEERING SUPPORT  
NUT, 7/8 DIA PUSHLOCK  
RING, EXT PUSH ON RTNR, 3/4  
JOINT, UNIVERSAL FEMALE  
RING, 3/4” KLIP  
SHAFT, LOWER STEERING  
KEY, 5MM SQ X 39MM L  
BEARING, 3/4” BORE FLANGED  
SCR, 5/16-18 X 3/4 CARRIAGE SS  
SPROCKET, STEERING SHAFT  
WASHER, 5/16 FLAT SS  
45012  
67416  
730319  
48110  
09072  
70593  
730315  
87029  
48045  
70377  
80595  
09148  
730221  
730316  
57022  
270088  
87008  
87162  
70175  
87083  
70806  
57023  
279001  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
-
KEY, 3/16 SQ X 5/8 LONG  
SCR, 3/8-16 X 1.25 HHCS SS  
FLANGE, BEARING PRESS STEEL  
BEARING, BALL 3/4 BORE SPHERED  
SPACER, .63 OD X .385ID X .64L  
SPROCKET, DRIVE WHEEL STEERING  
NUT, 3/8-16 HEX NYLOCK THIN SS  
CHAIN, ISO 08B, 12.7MM PITCH  
WASHER, 1/4 ID X 1-1/4OD  
WASHER, 1/4 SPLIT LOCK PLTD  
SCR, M6 X 20HHMS PLTD  
WASHER, 5/16 SPLIT LOCK  
SET SCR, M6 X 25 NP  
NUT, 5/16-18 HEX NYLOCK SS  
CHAIN, MASTERLINK 12.7MM  
86317500 CHARIOT SCRUBBER 11/15/08  
5-52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TANK  
86317500 CHARIOT SCRUBBER 11/15/08  
5-53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TANK  
SERIAL NO.  
FROM  
REF PART NO. PRV NO. QTY  
DESCRIPTION  
DOME, TANK, 20 X 21  
BASKET, STRAINER, DOME  
SCR, KA50X16, PT, WN1412, PLT  
SCR, 10-32 X 1/2 TORX SS BLK NP  
COLLAR, BAG  
NOTES:  
86313100  
86310190  
86014530  
86290540  
86315530  
86025200  
86199840  
86294250  
86317770  
86315550  
86314160  
86275800  
86317620  
86312050  
86279630  
86006760  
86004440  
86315500  
86314080  
86317360  
86314070  
86317370  
86256100  
86314050  
86246080  
86312800  
86317610  
86072390  
86002380  
86033570  
86003010  
86264950  
86305960  
86318090  
-
-
1
1
5
4
1
1
1
4
1
1
1
6
1
1
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
3
4
5
6
7
8
9
-
-
31377  
090-12A  
ELBOW ASM, FLOAT  
FLOAT SCREEN CAGE ASSY (SLIP)  
WASHER, .19ID X .5 X .09 THK BLK  
GASKET, DOME  
FRAME, BAG  
FILL PORT LID  
SCREW 8 X3/4 PFHT/S BLK ZINC  
RIM FILL PORT 4”BLACK W/O-RING  
TANK, BLUE TRIM  
WASHER, .344IDX1.13ODX.09T PLT  
SCR, 5/1618 X 3/4 HHCS GR5PLTDL  
CAP, DRAIN HOSE  
-
-
-
-
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33A  
33B  
70546  
-
-
87212  
70305  
39717  
-
-
-
-
HOSE, 2 X 30 DRAIN  
NUT, DRAIN FITTING  
GASKET, TANK DRAIN  
FITTING, DRAIN  
-
GASKET ASSY, DRAIN PLUG  
STRAINER, 3/4-MPT, 12 MESH  
PLUG, DRAIN  
LANYARD, 18.0 W/LOOP & EYE  
BAG RECOVERY  
GASKET, 5.5 OD X4.5ID X.06W/PSA  
BRKT, SCRUB DECK MOUNT  
CLAMP, 2.25 WORM GEAR  
TUBE ASM  
CUFF, HOSE 1.5” BLK A 2161  
CABLE TIE, .19W X 11.5 L BLK  
HOSE ASM, 1.5 BLK PVC VAC X 67  
HOSE ASM, W/90 DEGREE METRIC  
730333  
-
51368  
-
-
14365  
20046  
78934  
27759  
27746  
-
DISK  
CYLINDRICAL  
-
86317500 CHARIOT SCRUBBER 11/15/08  
5-54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VACUUM  
7
2
4
6
9
3
10  
11  
1
8
5
7
86317500 CHARIOT SCRUBBER 11/15/08  
5-55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VACUUM  
SERIAL NO.  
FROM  
REF PART NO. PRV NO. QTY  
DESCRIPTION  
NOTES:  
86314790  
86314780  
86012210  
86279630  
86010630  
86006760  
86005710  
86270830  
86237440  
86318080  
86264950  
-
-
-
3
1
1
1
3
1
6
2
1
1
2
1
2
3
4
5
6
7
8
9
ISOLATOR, RUBBER, 1/4-20 UNC M  
PLATE, VAC MOTOR  
VAC MOTOR, 36VDC 2ST TD  
WASHER, .344IDX1.130ODX.09T PLT  
WASHER, 1/4 X 5/8 FLAT SS  
SCR, 5/16-18 X 3/4 HHCS GR5  
NUT, 1/4-20 HEX W/STAR  
NUT, 5/16-18 HEX NYLOCK SS  
GASKET, 4.06 X 2.50 X .38  
MUFFLER ASSY, 1.5 HOSE  
CABLE TIE, .19W X 11.5L BLK  
87212  
87013  
70305  
57105  
57023  
35168  
-
10  
11  
27746  
86317500 CHARIOT SCRUBBER 11/15/08  
5-56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WHEEL-FRONT DRIVE  
2
1
19  
20  
21  
3
6
4
7
18  
8
29  
23  
9
10  
11  
12  
17A  
17B  
5
16  
13  
19  
15  
14  
28  
27  
26  
22  
30  
25  
24  
86317500 CHARIOT SCRUBBER 11/15/08  
5-57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WHEEL-FRONT DRIVE  
SERIAL NO.  
REF PART NO. PRV NO. QTY  
DESCRIPTION  
SCR, 3/8-16 X 1.25 HHCS SS  
WASHER, 3/8 SPLIT LOCK PLTD  
CABLE TIE, .375 X 24.7  
PIN, ROLL 1/8” X 3/4”L  
SPACER, 25.51 ID X 45 OD X 39.1 L  
SHAFT ASM, DRIVE PIVOT  
BRAKE, 36VDC W/CONNECTOR  
SCR, CAP 8-32 X 3/8 SHCS SS  
SCR, 1/4-20 X 1 FHCS PLTD  
TERMINAL MOUNT  
WASHER, 1/4 ID X 5/8 OD SS  
NUT, 1/4-20 HEX W/STAR WASHER  
SCR, 1/4-20 X 1.5 HHCS  
BOOT, RUBBER TERM. ISOLATOR  
CLAMP, 3/4 IDA CUSHION .406 DIA  
NUT, 1/4-20 HEX NYLOCK SS  
WHEEL, 10 X 2, 5 X 1.06 W/KEYWAY  
WHEEL, 10 X 2. 5 W/KEYWAY, GRY  
GEAR BOX DRIVE UNIT HELICAL  
SEALED BALL BRNG, 25MM X 52MM  
HUB STEERING  
FROM  
NOTES:  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
86275190  
86010790  
86002830  
86006170  
86224440  
86224020  
86001740  
70377  
87163  
27196  
66031  
730387  
730233  
140816  
4
4
1
1
1
1
1
4
2
2
2
4
2
2
1
2
1
1
1
3
1
2
1
86273340 00-000289  
86006840  
86257490  
86010630  
86005710  
86273740  
86008920  
86233410  
86005810  
70390  
76155  
87013  
57105  
70010  
80889  
81270  
57245  
89262  
89273  
-
09134  
41510  
67450  
70262  
-
17A 86011120  
17B 86259920  
OPTIONAL  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
-
86317190  
86223980  
86219420  
86223480  
86136640  
86318830  
86277340  
86279690  
86279710  
86225810  
86222720  
86222760  
86222770  
86317200  
86216210  
RING, 52MM INTERNAL SNAP  
SCR, M8-1.25 X 20 HHMS PLTD  
10 SCR, M10 X 30 SHCS  
70830  
87243  
87245  
87506  
620037  
620041  
620042  
-
4
4
1
1
1
1
1
1
-
SCR, M6 X 15 HHCS BLK  
WASHER, M6 SPLIT LOCK BLK  
WASHER, M8 (2THK X 26 OD)  
WASHER, ANTI-ROTATION  
PLATE, BEARING RETAINER  
PLATE, DRIVE YOKE RH  
PLATE, BEARING COVER  
DRIVE MOTOR ASSEMBLY HELICAL  
BRUSH SET MOTOR, 53810 86005510  
COMPLETE  
-
53820  
86317500 CHARIOT SCRUBBER 11/15/08  
5-58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WHEEL-REAR  
1A  
1B  
2
3
86317500 CHARIOT SCRUBBER 11/15/08  
5-59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WHEEL-REAR  
SERIAL NO.  
FROM  
REF PART NO. PRV NO. QTY  
DESCRIPTION  
NOTES:  
1A  
1B  
86011110  
86259930  
89261  
89274  
2
-
WHEEL, 10X2.5X.787ID BEARINGS  
WHEEL, 10X2.5, W/BEARINGS, GRY  
RING, ¾” EXT SNAP H-D  
OPTIONAL  
2
3
86008710  
86232130  
80623  
17309  
2
2
CAP, 2.75 ID X 1.0 L BLK VINYL  
86317500 CHARIOT SCRUBBER 11/15/08  
5-60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-BATTERIES  
2
3
4
1A  
1B  
20A  
20B  
20C  
5
9
24  
25  
10  
11  
23  
26  
7A  
7B  
6A  
6B  
8
12  
22  
13  
14  
15  
16  
19  
17  
18  
86317500 CHARIOT SCRUBBER 11/15/08  
5-61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-BATTERIES  
SERIAL NO.  
FROM  
REF PART NO. PRV NO. QTY  
DESCRIPTION  
NOTES:  
EURO  
1A  
1B  
2
86260200  
86002510  
86008920  
86271910  
86010670  
86264960  
86260610  
86002570  
86260230  
86002580  
86008760  
86229700  
86008300  
86008410  
86272810  
86092910  
86254990  
86278150  
86259910  
86088790  
86276070  
86270830  
80872  
23125  
80889  
57295  
87029  
27915  
880836  
23190  
80876  
23191  
80682  
08071  
78242  
78568  
67132  
51396  
730313  
70117  
89265  
78571  
70593  
57023  
10023  
10030  
10032  
02456  
02264  
57245  
28038  
70066  
87018  
57034  
2
2
6
6
6
2
1
1
1
1
1
3
1
1
1
1
1
8
8
2
4
4
3
3
3
1
1
8
1
1
1
1
WIRE, 4X14.5BK 3/8RINGX3/8RING  
CABLE ASM, BAT. JUMPER X 15”  
BOOT, RUBBER TERM. ISOLATOR  
NUT, 5/16-18 FLEXLOCK  
WASHER, 5/16 FLAT SS  
CABLE TIE, .375 X 43”  
WIRE, 4X25RD CTERM X 3/8RING  
WIRE, 4X27 RD BCLAMP X CTERM  
WIRE, 4X30 BK CTERM X 3/8RING  
WIRE, 4X27 BK BCLAMP X CTERM  
CONN, 175 DCA GRY W/O TERMS  
BLOCK, 3.0 X 1.5 X 1.5  
TRAY, BATTERY LINER  
TRAY, BATTERY  
RING, 1/2 EXT. SNAP H-D  
LATCH ROD, BATTERY TRAY  
SPRING, COMP, 63ODX3.5LX.047W  
SHOULDER BOLT, 5/16 OD X 1.0 L  
WHEEL, BATTERY TRAY  
3
4
5
6A  
6B  
7A  
7B  
8
EURO  
EURO  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
TRAY, STANDARD STOP  
SCR, 5/16-18 X 3/4 CARRIAGE SS  
NUT, 5/16-18 HEX NYLOCK SS  
BATTERY, 12V, 205AH  
20A 86228410  
20B 86283410  
20C 86228430  
21A 86284090  
21B 86000150  
BATTERY, 12V, 225AH  
BATTERY, 12V, AGM 198AH  
CHARGER, 36V, 20A, 115V, C175  
CHARGER, 36VDC/21A AGM  
NUT, 1/4-20 HEX NYLOCK SS  
CLAMP, CABLE KIT SY945  
SCREW, 10-32 X 3/4 PPHMS SS  
WASHER, #10 X 9/16 OD  
▲
▲
22  
23  
24  
25  
26  
86005810  
86233360  
86273980  
86010650  
86270890  
NUT, ACORN 10-32  
▲NOT SHOWN – FOR WET CELL BATTERIES AND AGM BATTERIES  
86317500 CHARIOT SCRUBBER 11/15/08  
5-62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-COMPONENTS  
1
2
3
4
5
6
6
86317500 CHARIOT SCRUBBER 11/15/08  
5-63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-COMPONENTS  
SERIAL NO.  
REF  
PART NO.  
86008920  
86270830  
86229770  
86273980  
PRV NO. QTY  
DESCRIPTION  
BOOT, RUBBER TERM. ISOLATOR  
NUT, 5/16-18 HEX NYLOCK SS  
BLOCK, SHUNT MOUNT  
SCR, 10-32 X 3/4 PPHMS  
GROMMET, 1.703 ID X 2.5 OD X .125  
GRV  
FROM  
NOTES:  
1
2
3
4
80889  
57023  
140805  
70066  
2
2
1
2
5
6
86238500  
86239720  
81427  
41520  
1
1
HORN, 108 DB MINATURE W/RING  
86317500 CHARIOT SCRUBBER 11/15/08  
5-64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-CONTROL PANEL  
70,71-BLK  
62-WHT  
30-GRY  
69-RED  
FROM C  
PIN 1 - 22-BRN  
PIN 2 - 23-BLU  
PIN 3 - 24-WHT  
65-WHT  
67-GRN  
38-YEL  
A
B
C
PIN 4 - 25-YEL  
PIN 5 - 26-GRN  
PIN 6 - 27-ORG  
PIN 7 - 28-VIO  
PIN C - 29-PNK  
1
7
C
31-BLK  
R-BRUSH  
L-BRUSH  
66-YEL  
32-GRY  
PROPEL  
19-PUR  
HORN  
HORN  
PF  
PF  
POT  
TB  
AUX3  
AUX3  
AUX2  
AUX2  
AUX1  
AUX1  
BRAKE  
BRAKE  
13-BRN  
14-BLU  
15-WHT  
16-YEL  
17-GRN  
18-ORG  
3- BLU  
POT  
WIPE  
B-SW  
B-SW  
CHRG  
TB1  
4- BLU  
SW1  
1
63-BRN  
62-WHT  
61-WHT  
37-WHT  
60-WHT  
59-BLU  
1
2
3
5
9
6
7
8
10  
11  
12  
13  
14  
4
K2  
K1  
2
0
-
P
N
N
K
5
8
-
B
R
5
6
9
1
2
3
10  
13  
7
8
11 14  
12  
4
-
+
RELAY JUMPERS  
PIN 6 K1-PIN 6 K2  
PIN 8 K1-PIN 4 K2  
PIN 9 K1-PIN 1 K2  
PIN 4 K1-PIN 8 K2  
PIN 10 K1-PIN 10 K2  
PIN 12 K1-PIN 12 K2  
PIN 13 K1-PIN 13 K2  
PIN 14 K1-PIN 9 K2  
PIN 11 K2-PIN 14 K2  
3
2
SWITCH SW1  
TB2  
TB1  
CONNECTOR - E  
CONNECTOR - B  
S1 - PIN 9 K1 / 51-WHT  
S2 - OPEN  
S3 - S4 / 56-BLK  
S4 - PIN 5 K1 / 50-BLU  
S5 - PIN 7 K2 / 55-VIO  
S6 - PIN 14 K2 / 53-GRN  
S8 - PIN 4 K2 / 54-ORG  
S9 - PIN 4 K1 / 52-YEL  
20  
10  
11  
1
14  
7
8
1
67-GRN  
73-BLU  
60-WHT - K1  
72-BRN  
33-PNK - C  
39A-GRN - C  
58-BRN - K1  
59-BLU - K1  
34-VIO - C  
39C-ORG - C  
9
14-BLK  
13-ORG  
BLU  
RED  
GRN  
ORG  
BRN  
6-BRN  
6B-BRN  
OPEN  
PIN 1  
PIN 1  
3
2
6
5
4
15-YEL  
16-BLK  
21-WHT/ORG  
22-WHT/BLK  
17-WHT/YEL  
18-BLU  
13-BRN  
14-BLU  
15-WHT  
16-YEL  
17-GRN  
18-ORG  
3- BLU  
PIN 1 - 22-BRN  
PIN 2 - 23-BLU  
PIN 3 - 24-WHT  
PIN 5 - 25-YEL  
PIN 6 - 30-GRY  
PIN 7 - 31-BLK  
PIN 8 - 32-GRY  
PIN 9 - 33-PNK  
PIN 10 - 34-VIO  
PIN 11 - 26-GRN  
PIN 12 - 27-ORG  
PIN 13 - 35-BRN  
PIN 1 - 19-VIO  
1
8
PIN 2 - 20-PNK  
PIN 3 - 16-TEL  
PIN 4 - 18-ORN  
PIN 8 - 13-BRN  
PIN 9 - 14-BLU  
PIN 10 - 15-WHT  
PIN 11 - 17-GRN  
19-WHT  
20-BLK  
4- BLU  
PIN 14 - 39B-ORG  
PIN 15 - 28-VIO  
PIN 16 - 29-PNK  
PIN 17 - 36-BLU  
PIN 18 - 37-WHT  
PIN 19 - 38-YEL  
PIN 20 - 39-GRN  
PANEL  
HARNESS  
PANEL  
HARNESS  
FROM MAIN HARNESS  
86317500 CHARIOT SCRUBBER 11/15/08  
5-65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-CONTROL PANEL  
SERIAL NO.  
REF  
PART NO.  
86313700  
86010860  
86010850  
PRV NO. QTY  
DESCRIPTION  
FROM  
NOTES:  
1
2
3
-
1
1
1
HARNESS, PANEL 2 STAGE  
880353  
880352  
WIRE, 4X20 BK CTERM C5/16RING  
WIRE, 4X2ORD CTERM C3/8RING  
86317500 CHARIOT SCRUBBER 11/15/08  
5-66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-DISK  
+Ubatt  
/
AUXsupplyPIN1  
19/VIO  
KSI-18  
-ESTOP  
63/BRN  
61/WHT  
OPTIONAL  
OPTIONAL  
-KSI  
72/BRN  
60/WHT  
45/BRN  
-PLATFORM  
46/BRN  
-K2  
-K2  
-K1  
-K1  
-FLASHER POWER  
-FLASHER GND  
-FLASHER  
-K1.  
-K2.  
43/BRN  
41/BRN  
48/BRN  
53/GRN  
47/BRN  
-REV(K2)  
42/BRN  
51/WHT  
52/YEL  
54/ORG  
-FLASHER UNIT  
-REV  
-K2  
-LED1  
FWR  
-LED2  
REV  
-FWR  
-K1  
55/VIO  
-FRONT FLASHER  
-FWRSW  
50/BLU  
-REAR FLASHER  
-TO AUX4  
-GND  
/
86317500 CHARIOT SCRUBBER 11/15/08  
5-67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-DISK  
B+  
CONNECTOR C  
-F1.6A  
E-STOP  
OPTIONAL  
XPORT  
LOW HIGH  
SINGLE  
MID  
THROTTLE  
-X10  
KEY  
REV  
HOURS  
CHARGER  
REVERSE ALARM  
& HORN  
DOUBLE  
-X15  
LOW  
-X3  
HIGH  
-X11  
VAC  
-X12  
-X20  
-X9  
-X18  
-X8 -X13  
-X16  
-X7  
-X19  
-X14  
38/YEL  
-X1  
-X2  
-X5  
-X6  
-X17  
-BRAKE/SW  
-K1  
INHIBIT  
-KEY  
TC  
-HM  
-10K  
-K1  
-K2  
-ESTOP  
ROTARY  
-HORN/SW  
67/GRN  
-R1/5KPOT  
-HORN  
LED  
86317500 CHARIOT SCRUBBER 11/15/08  
5-68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-DISK  
+Ubatt  
/
B+  
-U4  
CONNECTOR B  
AUX1  
-X4  
AUX2  
AUX3  
-X9  
AUX4  
-X2  
-X12 -X14 -X11  
-X10  
-X3  
-X8  
-X1  
B-  
-18A  
-BRUSHR  
M
-18A  
-BRUSHL  
M
M
M
-TRACTION  
-BRAKE  
-VACUUM  
-WATER  
M
M
M
TRACTION/SOLENOID  
24V FOR RELAYS  
-DECK  
-SOLUTION  
-SQUEGEE  
/
86317500 CHARIOT SCRUBBER 11/15/08  
5-69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-CYLINDRICAL  
+Ubatt  
/
AUXsupplyPIN1  
KSI-18  
-ESTOP  
OPTIONAL  
OPTIONAL  
-KSI  
-PLATFORM  
-K2  
-K2  
-K1  
-K1  
-FLASHER POWER  
-FLASHER GND  
-FLASHER  
-K1.  
-K2.  
-REV(K2)  
-FLASHER UNIT  
-REV  
-K2  
-LED1  
FWR  
-LED2  
REV  
-FWR  
-K1  
-FRONT FLASHER  
-FWRSW  
-REAR FLASHER  
-TO AUX4  
-GND  
/
86317500 CHARIOT SCRUBBER 11/15/08  
5-70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-CYLINDRICAL  
B+  
CONNECTOR C  
-F1.6A  
OPTIONAL  
XPORT  
LOW HIGH  
SINGLE  
MID  
THROTTLE  
-X10  
KEY  
E-STOP  
REV  
HOURS  
CHARGER  
REVERSE ALARM  
& HORN  
DOUBLE  
-X15  
LOW  
-X3  
HIGH  
-X11  
VAC  
-X12  
-X20  
-X9  
-X18  
-X8 -X13  
-X16  
-X7  
-X19  
-X14  
-X1  
-X2  
-X5  
-X6  
-X17  
38/YEL  
-BRAKE/SW  
-K1  
INHIBIT  
-KEY  
TC  
-HM  
-10K  
-K1  
-K2  
-ESTOP  
ROTARY  
-HORN/SW  
67/GRN  
-R1/5KPOT  
-HORN  
LED  
86317500 CHARIOT SCRUBBER 11/15/08  
5-71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-CYLINDRICAL  
/
+Ubatt  
B+  
-U4  
CONNECTOR B  
AUX1  
-X4  
AUX2  
AUX3  
-X9  
AUX4  
-X2  
-X12 -X14 -X11  
-X10  
-X3  
-X8  
-X1  
B-  
-18A  
-BRUSHR  
M
-18A  
-BRUSHL  
M
M
M
-TRACTION  
-BRAKE  
-VACUUM  
M
M
M
24V FOR RELAYS  
-DECK  
-SOLUTION  
-SQUEGEE  
-WATER  
-GND  
/
86317500 CHARIOT SCRUBBER 11/15/08  
5-72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-DRIVE MOTOR  
1 WHT  
2 BLK  
RED  
BLK  
1
2 BLK  
1 WHT  
2 BLK  
BLK  
WHT  
CONTROL PANEL  
HARNESS  
86317500 CHARIOT SCRUBBER 11/15/08  
5-73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-DRIVE MOTOR  
SERIAL  
REF PART NO. PRV NO. QTY  
86239120 41522  
DESCRIPTION  
NO.  
FROM  
NOTES:  
1
1
HARNESS, CHARIOT PROPEL  
86317500 CHARIOT SCRUBBER 11/15/08  
5-74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-MAIN HARNESS  
DIAGRAM A  
HORN  
13 ORG  
14 BLK  
TB2  
TB1  
67-GRN  
14-BLK  
13-ORG  
BLU  
73-BLU  
60-WHT - K1  
72-BRN  
19 WHT  
BRAKE  
15-YEL  
13-BRN  
16-BLK  
14-BLU  
20 BLK  
RED  
2
33-PNK - C  
39A-GRN - C  
58-BRN - K1  
59-BLU - K1  
34-VIO - C  
39C-ORG - C  
21-WHT/ORG  
DRIVE  
MOTOR  
GRN  
ORG  
BRN  
6-BRN  
6B-BRN  
OPEN  
15-WHT  
16-YEL  
17-GRN  
18-ORG  
3- BLU  
6 BRN  
6 BRN  
22-WHT/BLK  
17-WHT/YEL  
18-BLU  
19-WHT  
20-BLK  
4- BLU  
SOLENOID  
VALVE  
11 RED  
10 BLK  
PANEL  
HARNESS  
PANEL  
HARNESS  
FROM MAIN HARNESS  
RIGHT  
BRUSH  
MOTOR  
LEFT  
DIAGRAM B  
BRUSH  
3
MOTOR  
PUMP  
12 RED  
1
9 BLK  
17 LT BLU  
18 WHT/YLW  
SCRUB LIFT  
ACTUATOR  
DIAGRAM C  
4
VAC  
MOTOR  
11 RED  
D
10 BLK  
A
B
C
DIAGRAM D  
10 BLK  
5
11 RED  
SQUEEGEE LIFT  
ACTUATOR  
OPTIONAL  
WARNING LIGHTS  
86317500 CHARIOT SCRUBBER 11/15/08  
5-75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-MAIN HARNESS  
SERIAL  
REF PART NO. PRV NO. QTY  
DESCRIPTION  
HARNESS, MAIN  
HARNESS, PUMP JUMPER  
HARNESS, BRUSH MOTOR  
HARNESS BRUSH ACTUATOR  
HARNESS, WARNING LIGHTS  
OPTION  
NO.  
FROM  
NOTES:  
1
2
3
4
86313710  
86318640  
86318650  
86318660  
-
-
-
-
1
1
1
1
CYL ONLY  
CYL ONLY  
CYL ONLY  
5
86319780  
-
1
OPTION  
86317500 CHARIOT SCRUBBER 11/15/08  
5-76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-PEDAL PLATFORM  
A
8 BLU  
9 RED  
DIAGRAM A  
5 GRN  
7 BRN  
6 ORG  
86317500 CHARIOT SCRUBBER 11/15/08  
5-77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING-PEDAL PLATFORM  
SERIAL  
REF PART NO. PRV NO. QTY  
86315100  
DESCRIPTION  
HARNESS, PEDAL  
NO.  
FROM  
NOTES:  
-
1
1
86317500 CHARIOT SCRUBBER 11/15/08  
5-78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOSE DIAGRAM-DISK  
86282190 (13")  
PRV 39616  
TANK  
SHUT-OFF  
VALVE  
86281950 (32")  
PRV 39541  
STRAINER (FINE)  
STRAINER (COARSE)  
SOLENOID  
VALVE  
SCRUB DECK  
86317500 CHARIOT SCRUBBER 11/15/08  
5-79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOSE DIAGRAM-CYLINDRICAL  
TANK  
SHUT-OFF  
VALVE  
STARINER (COARSE)  
STRAINER (FINE)  
SOLENOID VALVE  
QUICK DISCONNECT  
86317500 CHARIOT SCRUBBER 11/15/08  
5-80  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SUGGESTED SPARE PARTS  
PART  
NO.  
SERIAL NO.  
FROM  
PRV NO.  
DESCRIPTION  
BREAKER, 18A, 250VAC, 32VDC  
BOOT, 7/16 CIRCUIT BREAKER  
CAP DRAIN HOSE  
NOTES  
86316160  
86008900  
86004440  
86199840  
86317770  
86305960  
86004860  
86004890  
86314050  
86313900  
86007170  
86007190  
86313820  
86009200  
86312800  
86001520  
86001540  
86001560  
86001570  
86001580  
86001630  
86001700  
86001740  
86231560  
86002780  
86007940  
86256120  
86292590  
86314150  
86295200  
86064300  
86242140  
86071030  
86010600  
86237440  
-
80845  
39717  
090-12A  
FLOAT, SHUT OFF  
-
GASKET, DOME EDGE  
-
HOSE ASM., 1.5” BLK PVC VAC X 67  
KEY, SWITCH  
48073  
48095  
KNOB, ALUM 3/8-16 NYLOCK NUT SS  
RECOVERY DRAIN PLUG 1-3/4  
RELAY, 15A 36V MINI  
-
-
72159  
SWITCH, 2 POSITION KEY  
72161  
SWITCH, DPST KEY  
-
SWITCH, SEALED PB ROUND  
KNOB, 3/8-16 4 PRONG ALUM  
BAG, INNER TANK  
81535  
-
140752  
BLADE, AQUAMIZER, 12IN LEFT  
BLADE, AQUAMIZER, 12IN RIGHT  
BLADE, SKIRT, SCRUB DECK, 24 IN LEFT  
BLADE, SKIRT, SCRUB DECK, 24 IN RIGHT  
BLADE, SQG REAR 40.6IN LINATEX  
BLADE, SQG FRONT 36.7IN RED GUM  
BLADE, SKIRT, SCRUB DECK, FRONT  
BRAKE, 36 VDC W/CONNECTOR  
CABLE, SQUEEGEE LIFT BASIC  
CABLE, SQUEEGEE LIFT DELUXE  
STRAINER, DEEP, 100 MESH  
STRAINER, 1/2 FPT 100 MESH  
SWTICH, E-STOP  
140753  
140754  
140755  
140763  
140764  
140780  
140816  
270097  
270098  
73836  
730368  
-
-
-
-
-
-
-
-
KNOB, SELECTOR  
ASM, BUTTON, BLACK, W/BEZEL  
PAD, TIPPING BAR  
KNOB, 3/8-16 X 1.5  
BRKT ASSEMBLY, REAR COVER  
VALVE, SOLENOID, 36VDC, 1/2 BARB  
GASKET, 4.06 X 2.50 X .38  
86317500 CHARIOT SCRUBBER 11/15/08  
5-81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPTIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BATTERY CART - OPTION  
27  
26  
28  
3
30  
5
2
6
24  
25  
3
29  
8
9
1
2
15  
3
4
3
23  
3
22  
5
5
10  
9
6
8
7
3
3
13  
12  
5
3
11  
14  
20  
8
21  
19  
16  
15  
18  
17  
16  
3
3
86317500 CHARIOT SCRUBBER 11/15/08  
6-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BATTERY CART - OPTION  
SERIAL NO.  
REF PART NO.  
PRV NO. QTY  
DESCRIPTION  
SCR, 5/16-18 X 1.00 BSHCS SS  
SPACER, 10D X .343ID, .5 LG  
NUT, 5/16-18 HEX NYLOCK SS  
HOUSING, BATTERY CART  
FROM  
NOTES:  
1
86006930  
86254290  
86270830  
86077010  
86010670  
86228840  
86259410  
86259400  
86254890  
86068490  
86254280  
86083120  
86076600  
86004070  
86276790  
86276690  
86199430  
86078890  
86277130  
86136730  
86232590  
86001350  
86011020  
86271840  
86008130  
86274730  
86070790  
86087340  
86070800  
86271870  
70514  
730338  
57023  
41517  
87029  
09124  
87206  
87205  
730018  
140019  
730331  
66442  
38318  
36196  
70732  
70715  
040-03  
620020  
70795  
70763  
18032  
140390  
89202  
57285  
73958  
70265  
140737  
730339  
140738  
57290  
2
4
33  
1
7
3
1
6
3
1
2
1
2
2
4
8
2
8
16  
1
2
2
2
2
2
2
2
2
2
2
2
3
4
5
WASHER, 5/16 FLAT SS  
6
BEARING, FLANGED .314D X .502OD  
WASHER, THRUST, .51 ID X 1 OD X .063  
WASHER, THRUST .51 ID X 1 OD  
SPRING, EXT, .50D X 4.0L  
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
BRKT, TRAY CATCH  
SPACER, 1.00 OD X .32 ID X .375  
PLATE, BATTERY CART BACK  
HANDLE, BATTERY CART  
GRIP, POLISHER HANDLE  
SCR, 5/16-18 X 1.75 HHCS SS  
SCR, 5/16-18 X 1.75 CARR SS  
CASTER SWIVEL 4” 250# CPCTY  
PLATE, CASTER SPACER  
SCR, 5/16-18 X 1.00 CARRIAGE SS  
SCR, M6-1 X 40MM PLTD  
CASTER, 4” HARD RUBBER RIGID  
BUSHING, SPANNER .435 X 1.10  
WHEEL, 3” DIA CUSHION RUBBER  
NUT, 5/16-18 HEX NYLOCK THIN SS  
SPACER, 3/8OD X .62W X .312L, AL  
SCR, 1/4-20 X 3/4 SHCS PLTD  
BRKT, BATTERY LOCK MOUNT  
SPACER, LATCH GUIDE  
BRKT, BATTERY TRAY LOCK  
NUT, 1/4-20 HEX NYLOCK THIN SS  
86317500 CHARIOT SCRUBBER 11/15/08  
6-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BATTERY CART - OPTION  
1
2
4
5
3
7
7
5
6
10  
3
8
9
17  
6
10  
3
11  
12  
13  
14  
15  
6
10  
3
3
10  
16  
86317500 CHARIOT SCRUBBER 11/15/08  
6-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BATTERY CART - OPTION  
SERIAL NO.  
REF PART NO.  
PRV NO. QTY  
DESCRIPTION  
FROM  
NOTES:  
1
2
86078330  
86276070  
86270830  
86087800  
86228840  
86259410  
86006560  
86077140  
86226830  
86010670  
86244280  
86276060  
86254280  
86231150  
86259400  
86276690  
86077530  
66478  
70593  
57023  
730307  
09124  
87206  
70083  
51404  
73268  
87029  
500934  
70590  
730331  
09151  
87205  
70715  
51403  
1
2
PEDAL, BATTERY CART  
SCR, 5/16-18 X 3/4 CARRIAGE SS  
NUT, 5/16-18 HEX NYLOCK SS  
STIFFENER, PEDAL, BATTERY CART  
BEARING, FLANGED .314ID X .502OD  
WASHER, THRUST .51 ID X 1 OD X .063  
SCR, 5/16-18 X 1 HHCS SS  
3
12  
2
4
5
4
6
6
7
4
8
2
LATCH, BATTERY CART  
9
2
SPRING, EXT .68D X 3.00L X .098W  
WASHER, 5/16 FLAT SS  
10  
11  
12  
13  
14  
15  
16  
17  
10  
1
LABEL, BATTERY CART OPERATION  
SCR, 5/16-18 X 2.5 CARR GR5  
SPACER, 1.00 ODX .32ID X .375  
BUSHING FLANGE, .314 X .502 OD  
WASHER, THRUST .51 ID X 1 OD  
SCR, 5/16-18 X 1.75 CARR SS  
LINKAGE, LATCH, BATT CART  
4
12  
4
8
16  
2
86317500 CHARIOT SCRUBBER 11/15/08  
6-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEAT - OPTION  
2
13  
14  
1
12  
11  
3
4
5
6
10  
9
8
7
15  
16  
17  
18  
19  
20  
23  
24  
22  
21  
86317500 CHARIOT SCRUBBER 11/15/08  
6-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEAT - OPTION  
SERIAL NO.  
FROM  
REF  
1
PART NO.  
86248390  
86082640  
86276890  
86279460  
86270710  
86271930  
86278910  
86070830  
86070840  
86277710  
86008650  
86246320  
86272300  
86251860  
86279620  
86276070  
86277510  
86009200  
86254300  
86094000  
86276710  
86093790  
86010670  
86270830  
PRV NO.  
730324  
629995  
70752  
QTY  
1
DESCRIPTION  
PAD, REAR REST  
NOTES:  
2
1
PLATE, SEAT COVER  
3
4
SCR, 5/16-18 X 3/4 PTHMS SS  
WASHER, 1/2 SPLIT LOCK  
NUT, WING 3/8-16  
4
87164  
2
5
01-000277  
57297  
1
6
1
NUT, 3/8-16 HEX NYLOCK SS  
WASHR, 3/8 ID X 7/8 OD SS  
BRKT, LEFT REAR SEAT  
BRKT, RIGHT REAR SEAT  
SCR, 3/8-16 X 2.75 HHCS SS  
COTTER, 1/4” RING  
7
87003  
3
8
140742  
140743  
730347  
80604  
1
9
1
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
1
1
51142  
1
LEVER, HANDLE LOCK  
66133  
1
PIN, CLEVIS 3/16 X .88 PLTD  
ROD, ARM HANDLE LOCK 4” LG  
WASHER, .4ID X 1.3OD NYLON  
SCR, 5/16-18 X 3/4 CARRIAGE SS  
SCR, 3/8-16 X 5.0 HHCS SS FT  
KNOB, 3/8-16 4 PRONG ALUM  
SPACER, SEAT LOCK  
66481  
1
87200  
2
70593  
2
70857  
1
81535  
1
730350  
05246  
1
1
SEAT MOUNT POST  
70717  
2
SCR, 5/16-18 X 2.0 CARRIAGE SS  
RECEIVER ASSY, SEAT MOUNT  
WASHER, 5/16 FLAT SS  
05247  
87029  
1
4
57023  
4
NUT, 5/16-18 HEX NYLOCK SS  
86317500 CHARIOT SCRUBBER 11/15/08  
6-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING LIGHTS - OPTION  
1
6
2
3
3
4
FRONT  
5
7
3
1
2
6
REAR  
86317500 CHARIOT SCRUBBER 11/15/08  
6-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING LIGHTS - OPTION  
SERIAL NO.  
REF  
1
PART NO.  
86270990  
86010650  
86276820  
86071490  
86270990  
86246200  
86071500  
PRV NO. QTY  
DESCRIPTION  
FROM  
NOTES:  
57090  
87018  
70740  
140871  
57090  
51454  
140872  
4
4
4
1
2
2
1
NUT, 10-32 HEX NYLOCK SS  
WASHER, #10 X 6/16 OD  
2
3
SCR, 10-32 X 1/2 PTHMS BLK  
BRKT, UPPER WARNING LIGHT  
NUT, 10-32 HEX NYLOCK SS  
LED AMBER LIGHT, 12V  
4
5
6
7
BRKT, LOWER WARNING LIGHT  
86317500 CHARIOT SCRUBBER 11/15/08  
6-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERIAL NUMBERS  
REF.  
NO.  
MODEL: SERIAL #  
1
N/A  
86317500 CHARIOT SCRUBBER 11/15/08  
6-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Westinghouse Cell Phone LD 268 SERIES User Manual
Whistler Radar Detector 1750 User Manual
White Lawn Mower 128 476R190 User Manual
White Rodgers Furnace 21D83M 843 User Manual
Windsor Carpet Cleaner 10080220 User Manual
Wow Wee Time Clock 8032 User Manual
Xantech Network Router RT16 10 User Manual
Zanussi Cooktop ZVH 66 F User Manual
Zanussi Freezer ZVC 45 AL User Manual
Zenith Flat Panel Television 22LCD3 User Manual