Wilton Saw SX User Manual

This Manual is Bookmarked

Owner's Manual

Cold Saw

Models: FK350-2, FK350-2SX, FK350-4, FK350-4SX

FK350

FK350-SX

WMH TOOL GROUP

2420 Vantage Drive

Elgin, Illinois 60124

Ph.: 800-274-6848

Part No. M-FK350-2

Revision B 02/07

www.wmhtoolgroup.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Warranty and Service....................................................................................................................................2

Table of Contents..........................................................................................................................................3

Warnings .......................................................................................................................................................4

Introduction ...................................................................................................................................................6

Specifications................................................................................................................................................6

Cutting Capacity (All Models)....................................................................................................................6

FK350 Features.........................................................................................................................................7

Features ........................................................................................................................................................8

Miter Cutting Head.....................................................................................................................................8

Miter Position Lock ....................................................................................................................................8

Self-centering Vise ....................................................................................................................................8

FK350 Controls..........................................................................................................................................8

FK350-SX Controls....................................................................................................................................8

Trigger Handle...........................................................................................................................................8

Flood Coolant System ...............................................................................................................................8

Installation.....................................................................................................................................................9

Unpacking the machine.............................................................................................................................9

Anchoring and handling the machine........................................................................................................9

Electrical Connections...................................................................................................................................9

Controls.......................................................................................................................................................10

Control Panel – FK350............................................................................................................................10

Trigger Handle – FK350..........................................................................................................................10

Control Panel – FK350-SX......................................................................................................................10

Operation.....................................................................................................................................................11

FK350......................................................................................................................................................11

FK350-SX................................................................................................................................................11

Miter Adjustment......................................................................................................................................12

Trip Adjustment – FX350-SX...................................................................................................................12

Depth Stop – FK350................................................................................................................................12

Maintenance................................................................................................................................................13

Maintenance Requirements ....................................................................................................................13

Periodic Maintenance..............................................................................................................................13

Coolant ....................................................................................................................................................13

Changing the Saw Blade.........................................................................................................................13

Air Prep Unit – FK350-SX only................................................................................................................13

Lubrication...............................................................................................................................................14

Coolant System .......................................................................................................................................14

Blade Selection ...........................................................................................................................................15

Troubleshooting ..........................................................................................................................................18

Parts............................................................................................................................................................19

Ordering Replacement Parts...................................................................................................................19

Head Assembly – FK350 & FK350-SX....................................................................................................20

Power Feed Assembly – FK350-SX........................................................................................................22

Stock Stop Assembly...............................................................................................................................24

Stand Assembly – FK350........................................................................................................................25

Stand Assembly – FK350-SX..................................................................................................................26

Base Assembly – FK350.........................................................................................................................28

Base Assembly – FK350-SX...................................................................................................................30

Manual Vise Assembly – FK350 .............................................................................................................32

Power Vise Assembly – FK350-SX.........................................................................................................34

Guard Assembly – FK350 & FK350-SX ..................................................................................................36

In-Feed Table Assembly..........................................................................................................................38

Out-Feed Table .......................................................................................................................................39

Pneumatic Drawing – FK350-SX ................................................................................................................40

Wiring Diagram – FK350.............................................................................................................................40

Wiring Diagram – FK350-SX.......................................................................................................................41

Download from Www.Somanuals.com. All Manuals Search And Download.

Warnings

1. Read and understand the entire owner's manual before attempting assembly or operation.

2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with

all of these warnings may cause serious injury.

3. Replace the warning labels if they become obscured or removed.

4. The cold saw is designed and intended for use by properly trained and experienced personnel only. If

you are not familiar with the proper and safe operation of a cold saw, do not use until proper training

and knowledge have been obtained.

5. Do not use this cold saw for other than its intended use. If used for other purposes, WMH Tool Group

disclaims any real or implied warranty and holds itself harmless from any injury that may result from

that use.

6. Always wear approved safety glasses/face shields while using this cold saw. Everyday eyeglasses

only have impact resistant lenses; they are not safety glasses.

7. Before operating the cold saw, remove tie, rings, watches and other jewelry, and roll sleeves up past

the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips

are recommended. Do not wear gloves.

8. Wear ear protectors (plugs or muffs) during extended periods of operation.

9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities

contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples

of these chemicals are:



Lead from lead based paint.

Crystalline silica from bricks, cement and other masonry products.

Arsenic and chromium from chemically treated lumber.

10. Your risk of exposure varies, depending on how often you do this type of work. To reduce your

exposure to these chemicals, work in a well-ventilated area and work with approved safety

equipment, such as face or dust masks that are specifically designed to filter out microscopic

particles.

11. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

12. Make certain the switch is in the OFF position before connecting the machine to the power supply.

13. Make certain the machine is properly grounded.

14. Make all machine adjustments or maintenance with the machine unplugged from the power source.

15. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting

wrenches are removed from the machine before turning it on.

16. Keep safety guards in place at all times when the machine is in use. If removed for maintenance

purposes, use extreme caution and replace the guards immediately.

17. Make sure the cold saw is firmly placed on a secure foundation.

18. Check damaged parts. Before further use of the machine, a guard or other part that is damaged

should be carefully checked to determine that it will operate properly and perform its intended

function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting

and any other conditions that may affect its operation. A guard or other part that is damaged should

be properly repaired or replaced.

19. Provide for adequate space surrounding work area and non-glare, overhead lighting.

20. Keep the floor around the machine clean and free of scrap material, oil and grease.

21. Keep visitors a safe distance from the work area. Keep children away.

22. Make your workshop child proof with padlocks, master switches or by removing starter keys.

Download from Www.Somanuals.com. All Manuals Search And Download.

23. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are

careless acts that can result in serious injury.

24. Maintain a balanced stance at all times so that you do not fall into the blade or other moving parts. Do

not overreach or use excessive force to perform any machine operation.

25. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for

which it was not designed. The right tool will do the job better and safer.

26. Use recommended accessories; improper accessories may be hazardous.

27. Maintain tools with care. Keep saw blades sharp and clean for the best and safest performance.

Follow instructions for lubricating and changing accessories.

28. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do

not use your hands.

29. Do not stand on the machine. Serious injury could occur if the machine tips over.

30. Never leave the machine running unattended. Turn the power off and do not leave the machine until it

comes to a complete stop.

31. Remove loose items and unnecessary work pieces from the area before starting the machine.

Familiarize yourself with the following safety notices used in this manual:

This means that if precautions are not heeded, it may result in minor injury and/or

possible machine damage.

This means that if precautions are not heeded, it may result in serious injury or possibly

even death.

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

The FK350 and FK350-SX are circular saws designed to provide a reliable solution to the needs of

machine shops and production environments that work with steel or iron. The FK350 is manually

operated: after clamping the material in the vise, the operator presses the trigger handle starting the

blade, and brings the operating lever downward to cut the material. The SX offers both semi-auto and

manual mode. When in semi-auto mode, operator positions material, and then presses the cycle-start

button. The saw control system activates the vise and clamps the material, and brings the head down

completing the cut. The head then is raised and the vise released, completing the cycle. An optional foot

switch is available to facilitate convenient cycle-start. The FK350 and FK350-SX can perform miter cuts

up to 45º to the right or left.

Specifications

Model...................................FK350-2 .....................FK350-4.................FK350-2SX................ FK350-4SX

Disc Blade

Disc diameter ..............14" (350mm) ..............14" (350mm).............. 14" (350mm) ............. 14" (350mm)

Hole diameter................1.3" (32mm) ...............1.3" (32mm)............... 1.3" (32mm) .............. 1.3" (32mm)

Blade thickness............0.1" (2.5mm) ..............0.1" (2.5mm).............. 0.1" (2.5mm) ............. 0.1" (2.5mm)

Cutting Speed

Blade Speed (RPM) ................ 44/88 ......................... 44/88.......................... 44/88.......................... 44/88

Motor

Motor ................................. 2HP/3HP ................... 2HP/3HP.................... 2HP/3HP....................2HP/3HP

Voltage ................................220VAC .....................440VAC......................220VAC......................440VAC

Other

Coolant Capacity......................3 gal. ..........................3 gal........................... 3 gal........................... 3 gal.

Dimensions .......25"L x 43"W x 75"H ...25"L x 43"W x 75"H....28"L x 50"W x 60"H....28"L x 50"W x 60"H

Weight ....................................720lbs ........................720lbs.........................800lbs........................ 800lbs

Cutting Capacity (All Models)

Degree Round

Square

4.25"

3.5"

Rectangle

5.5" x 3.75"

3.5" x 3.5"

2" x 2"

90°

45°

90°

45°

4.5"

3.5"

Tubing

Solid

1.75"

1.75" x 1.75"

The specifications in this manual are given as general information and are not binding. WMH Tool Group

reserves the right to effect, at any time and without prior notice, changes or alterations to parts, fittings,

and accessory equipment deemed necessary for any reason whatsoever.

Download from Www.Somanuals.com. All Manuals Search And Download.

FK350 Features

FK350 Cold Saw

FK350-SX Cold Saw

Download from Www.Somanuals.com. All Manuals Search And Download.

Features

Miter Cutting Head

The miter cutting head is the unit that cuts the

material and consists of a cast iron base, blade

support unit and guard, transmission unit, and

motor. The depth of cut is set by adjusting the

depth cut stop. The miter cutting head swivels

and locks into -45º, 90º, and +45º by means of a

locking mechanism. Depressing the mechanism

overrides the lock, permitting the head to adjust

to any position between -45º and +45.

Figure 1

Flood Coolant System

Miter Position Lock

The miter position lock secures the miter cutting

head from movement. The miter is secured

when the lock is pushed all the way to the left

and can be positioned when the lock is moved to

the right.

The coolant pump must be

submerged before operating to prevent

damage to the pump.

Coolant is dispensed directed onto the saw

blade from a coolant fitting on the upper blade

guard. Coolant is provided through tubing from

the coolant pump (Figure 2) in the machine

base.

Self-centering Vise

The self-centering vise holds the work piece in

place during cutting. The work piece is secured

in the vise by turning the vise handles.

Adjust the coolant flow valve on coolant fitting to

achieve desired flow. When the coolant switch is

in the ON position, flow starts when the drive

motor is started. Turning off the coolant switch

stops coolant flow.

FK350 Controls

The control panel consists of the Power (On/Off)

switch and High/Stop/Low switch, and an

integral coolant system. To operate the

machine, the Power switch must be set to on

and the High/Stop/Low switch must be set for Hi

or Low. Then depress the trigger handle to start.

This coolant system can operate with either a

soluble oil base coolant or water-soluble

synthetic coolant. Coolant should be changed

regularly. Some recommended brands are DoAll

and Lenox. These coolants are available at your

local industrial distributor.

FK350-SX Controls

This machine features a 2-speed motor, feed

speed control, an integral coolant system, and

two modes of operation; manual mode, and

semi-automatic mode. In semi-auto, the

complete cut cycle is initiated via push button.

The semi-auto cut cycle closes the vise

clamping the material, powers the head down

completing the cut, then raises the head, and

opens the vise. In manual mode, head up/down,

and vise open/close is initiated by switches.

Trigger Handle

The trigger handle (Figure 1) is located on the

operating lever used to raise and lower the saw.

It contains a micro-switch, which is activated

when the operator depresses the run trigger.

Figure 2

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Electrical Connections

All electrical connections

Unpacking the machine

must be done by a qualified

electrician. All adjustments or repairs must

be done with the machine disconnected from

the power source, unplugged. Failure to

comply may result in serious injury!

Do not handle the packed

machine using slings.

To install the machine, first remove the packing,

paying particular attention not to cut any electric

wires or hydraulic hoses. Lift using straps

(Figure 3).

FK350-2 and FK350-2SX are rated at 220V.

FK350-4 and FK350-4SX are rated at 440V.

These machines not supplied with a plug. Use a

plug and outlet rated at least 20amps. The

circuit for the machine should also be protected

by at least a 20 amp circuit breaker or fuse.

Make sure that the blade turns in the correct

direction. If it does not, simply reverse two of

the phase wires on the supply input.

The sawing machine is now ready for use.

Figure 3

Anchoring and handling the machine

The base of the machine must be anchored to

the floor by two lag bolts or studs properly

anchored into concrete.

Download from Www.Somanuals.com. All Manuals Search And Download.

Control Panel – FK350-SX

Controls

Emergency – Emergency Stop: This turns off

the controls, and the machine. When used, it

requires that “Control On” button be pushed.

Control Panel – FK350

The Control Panel (Figure 4) is located on the

front the cabinet stand and consists of the

Power and High/Stop/Low switches, described

below.

Vise – Open/Close (Manual mode

Mode selection – Select Semi-auto, or Manual

mode.

Start – In manual mode, this starts the saw

blade. In Semi-auto, this starts the cut-cycle.

Power Switch – The Power switch has two

positions, Off and On.

Head-UP/ Head-Down – Manual mode only

Feed rate – sets feed rate of cut cycle

High/Stop/Low Switch – This switch controls

the blade speed. To operate the saw, the power

switch must set to on, High or Low must be

selected and the Run Trigger depressed.

Figure 4

Trigger Handle – FK350

Figure 6

To operate, the Power switch must be set to on

a Hi or Low speed selection made, and the

trigger handle, depressed.

High/Stop/Low Switch – Refer to Figure 7;

located on the front of the cabinet stand;

controls the blade speed (Figure 7).

Figure 5

Figure 7

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Before using the machine:



Check that safety devises (ex., blade

guards) are in position and work perfectly

and that personal safety requirements are

complied with.



Check the sharpness of the blade and verify

coolant flow.

FK350-SX

To operate machine,

1. Clear the Emergency Stop.

2. Press Control On.

FK350

1. Make sure the work piece is securely

clamped in the vise.

3. Select the desired blade speed.

4. Select Manual or Semi-auto.

2. Turn the power on (A, Fig. 8).

3. Select the cutting speed (B, Fig. 8).

Manual Mode – Position material and tighten

the vise. Position the head switch to Head-Down

until cut is complete. Position the head switch to

Head-Up until head retracts to desired height.

Semi-auto Mode – Set the head travel trips to

achieve desired head travel extents. Position

material in the vise allowing approximately .125"

for proper air vise operation, and then press

cycle start. After the cycle is complete, the vise

opens for material repositioning.

Note: The coolant pump is activated while the

motor is running.

Figure 8

4. Grip the trigger handle (Figure 5) on the

control lever.

5. Start the blade by pressing the micro-switch

on the handgrip.

The down stroke speed of the head is controlled

manually by the operator. The coolant pump is

activated during the time that the head is below

the upper limit position.

When the cut is complete:

6. Raise the head.

7. Remove the work piece from the vise using

the vise hand wheels.

Figure 9

Download from Www.Somanuals.com. All Manuals Search And Download.

Miter Adjustment

The adjust the miter position follow the steps

below while referring to Figure 10:

1. Move the miter position lock (A) to the right

to release.

2. Adjust the head to the desired angle ranging

from –45º to +45º by pushing on the back of

the motor to the right or left. The miter

position is shown on the scale (B).

3. A detent mechanism locks the head in

the -45º, 90º and +45º positions and will

prevent the head from rotating. For a miter

position other than -45º, 90º and +45º, press

the lever (C) to release while rotating the

head.

4. When the desired cutting angle is set, move

miter position lock (A) to the left to secure.

Figure 11

Depth Stop – FK350

The depth cut stop adjustment limits the lower

travel limit of the saw blade during a cutting

operation.

Remove

power

when

making this adjustment.

Failure to comply may result in serious

injury!

Figure 10

Trip Adjustment – FX350-SX

To adjust the depth of cut (refer to Figure 12):

The height of retract and depth of cut trips set

the travel limit of the head.

1. Using two 13mm wrenches, loosen the lock

nut (A).

Te set the trips (refer to Figure 11):

2. With the saw in the fully lowered position,

turn the screw (B) until the saw blade

bottoms out at the desired level.

1. Turn the machine on and run in manual

mode.

3. Tighten the lock nut.

2. Move the head up to the desired height of

retract position.

3. Loosen the lock knob (A) and slide the trip

(B) down until it makes contact with the trip

plate (C).

4. The trip plate fixes the position mechanically

while the limit switch (D) signals the control

system.

5. Tighten the lock knob.

6. Move the head down to the desired depth of

cut position.

Figure 12

7. Loosen the lock knob (E) and slide the trip

(E) up until it makes contact with the trip

plate (not visible in Figure 11).

8. Tighten the lock knob.

Download from Www.Somanuals.com. All Manuals Search And Download.

Air Prep Unit – FK350-SX only

Maintenance

The Air Prep Unit regulates the air pressure

supplied to the saw. It is located in the cabinet

stand and is accessible through the access door

located below and to the left of the control panel.

Referring to Figure 13, it consists of a pressure

regulator, pressure gauge, water trap and

lubricator. Air pressure (90lbs. minimum) is

supplied to the air intake valve located near the

bottom of the cabinet on the left side. The

pressure regulator should be adjusted to 90–

120lbs.

Maintenance Requirements

All maintenance must be

carried out with the power switched off.

Failure to comply may result in serious

injury!

On completion of maintenance, ensure that

replaced parts and/or any tools used have been

removed from the machine before starting it up.

Required Maintenance:

Periodic Maintenance



Check weekly.

Drain water from the trap when the level

exceeds the redline.

Adjust to 2 –3 drops/minute. Refill oil when

the level drops below the lower redline. Do

not exceed past the upper redline.



Remove chips from the machine, preferably

with cloth)

Remove chips from the coolant tank and

change coolant regularly (see Coolant

section)

Top up the coolant level (see Coolant)

Check the wear of the blade and change if

necessary (see Changing the Saw Blade)

Empty the chips out of the base.

Clean the vise and lubricate all the joints

and sliding surfaces, using good quality oil.

Attend to daily, weekly and annual

lubrication recommendations (see the

Lubrication section)



Coolant

The coolant tank access door is located on the

back of the cabinet stand. Remove four hex cap

screws with a 5mm hex wrench. Check coolant

level in the coolant tank periodically and top off if

necessary. Coolant can also be added by

pouring directly on the table, which will drain into

the tank through the chip strainer.

Remove excess chips periodically from the tank.

Use the coolant level gauge to check the coolant

level.

Changing the Saw Blade

Figure 13

The cold saw must not be

connected to the power source when

changing saw blades. Failure to comply may

result in serious injury!

To change the saw blade:

1. Switch off the machine.

2. Release the lower disc guard.

3. Move the lower guard upwards.

4. Remove the blade and replace it with a new

one.

5. To secure the saw blade, reverse the

preceding steps.

Download from Www.Somanuals.com. All Manuals Search And Download.

Lubrication

For long life and trouble free operation, it is

essential that this machine is kept well

lubricated. The vice and leadscrew should be

oiled daily. Pivot joints and bearings should be

greased weekly Check the gearbox oil level

weekly, full level is top of sight glass with head

in full up position. The gearbox oil should be

changed annually, and the hydraulic fluid

[FK350-SX] should be changed annually.

Recommended Lubricants:

Gearbox

Use Texaco Meropa 460 or equivalent.

Grease fittings

Texaco Starplex 2 or equivalent

Hydraulic fluid [FK350-SX]

Texaco Rando HDZ22 or Spindura 22

Vice and Leadscrew

Regal R & O 68

Coolant System

This coolant system can operate with either a

soluble oil base coolant or water-soluble

synthetic coolant. Coolant should be changed

regularly. Some recommended brands are DoAll

and Lenox. These coolants are available at your

local industrial distributor.

Coolant Type:



Soluble Oil Base

Water-Soluble Synthetic Coolant

Download from Www.Somanuals.com. All Manuals Search And Download.

Blade Selection

When using the FK350 cold saw, it is important

to select the correct type of blade for the

material to be cut. This section explains the

limitations and specific applications of the

different types of blades.

General Characteristics:

Fine Tooth Pitch --used for thin wall materials

such as sheet steel, tubes and profiles

Coarse Tooth Pitch --used for large cross-

sections -- for soft materials (aluminum alloys

and soft alloys in general).

Determining Proper Tooth Pitch

Table 1

Proper tooth pitch depends on:

A larger pitch should be chosen when, as a

result of the shape of the piece to be cut, the

cross-section at any given point exceeds the

average cross-section given above.

a) the size of the section;

b) the hardness of the material;

c) wall thickness.

Solid sections call for

discs with a coarse

tooth pitch, while

small cross-sections

require blades with

finer teeth. This is

because when cutting

walls of small cross-

section (1–7 mm)

profiles, it is important that the number of teeth

actually making the cut should not be too small,

otherwise the effect obtained will be one of

tearing rather than of chip removal, leading to a

large increase in shearing stress. On the other

hand, when cutting thick materials or solid

sections using an excessively fine tooth pitch,

the chip collects as a spiral inside the gullet, and

since fine tooth pitches have small gullets, the

accumulated chip will exceed the gullet capacity

and press against the walls of the workpieces,

resulting in poor cutting (same situation with soft

materials), greater shearing stress and hence

breakage of the blade.

Cutting and Feeding Speed

The cutting speed, in m/min, and the head

feeding speed, in cm²/min, are limited by the

amount of heat generated near to the points of

the teeth. If the head feeding speed is too high,

the cut will not be straight in either the vertical or

the horizontal plane. As we have already said,

the cutting speed depends on the strength

(kg/mm²) and hardness (HRC) of the material

and the dimensions of the thickest section. The

feeding speed depends on the cross-section of

the material. Solid or thick-walled materials

(thickness>5mm) can therefore be cut at high

speed providing there is sufficient swarf removal

by the blade, while thin-walled materials such as

tubes or thin profiles must be cut with a low

feeding speed.

A new blade requires a

break-in period, during which time about half

the normal feeding speed should be used.

Coolant

The cooling fluid ensures that the blade teeth

and material in the area of the cut do not

overheat. The fluid must be an excellent

lubricant so as to prevent abrasion of the teeth

and welding of the chips to the teeth themselves

(seizing).

Download from Www.Somanuals.com. All Manuals Search And Download.

Blade Structure

For non--ferrous metals, it is common to use

circular saws with brazed hard metal HM cutting

edge, consisting of a disc made of alloy tool

steel (71Cr1) on which the shape of the teeth

and the seats for the cutting edges are made of

Widia K10. These saws have shown excellent

wear resistance but low resistance to impact,

which is in any case a minor problem with non-

ferrous materials.

Figure 14

”BW” TYPE SHARPENING DIN 1838--UNI 4014

Coarse toothing with teeth alternately raked to

the right and left.

Toothing generally used on cutting-off machines

for cutting ferrous and alloy materials with

tubular and profiled sections.

Table 2

Types of Blades

The blades fitted to the FK350 and FK350-2SX

have dimensions 350 x 32 x 2.5 mm and are of

HM hard steel type since the machine is to be

used for cutting non-ferrous materials. In

addition to the size and pitch of the teeth,

however, the blades also have different

geometric characteristics in accordance with

their particular use:

Figure 15

POSITIVE AND NEGATIVE CUTTING ANGLES

The cutting angle may vary from positive to

negative depending on the cutting speed, the

profile and the type of material to be cut.

tooth cutting angle – may be negative or

positive

tooth sharpening –may be BW with an

alternate raked tooth or C with a roughing tooth

raked on both sides and a non--raked finishing

tooth

tooth pitch – the distance between the crest of

one tooth and the crest of the next tooth (tooth

pitch = T)

Figure 16

Teeth Shape

A positive angle determines better penetration of

the tool and hence lower shear stress and

greater ease of sliding for the swarf over the

cutting edge. On the other hand, the cutting

edge has lower mechanical resistance, so as the

breaking load of the material to be cut increases,

the cutting angle decreases from positive until it

becomes negative so as to offer a cutting edge

with a larger resistant section.

”C” TYPE SHARPENING (HZ)

Coarse toothing with roughing tooth raked on

both sides and non--raked finishing tooth. The

roughing tooth is about 0.3 mm higher.

Coarse toothing with roughing tooth and

finishing tooth. Used in saws with pitch greater

than or equal to 5 mm for cutting ferrous and

non-ferrous materials with solid or solid-profiled

sections.

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 17

Figure 19

Short swarf material such as brass, bronze,

aluminum and hard cast iron require smaller

cutting angles because the swarf becomes

crushed immediately and the rake angle has

little effect during the cutting stage.

Circular saws can also be characterized by other

parameters such as the whine reduction feature,

which cuts down noise at high speeds, or

expansion, which compensates for the pushing

of chips inside the cutting edge, thus reducing

the thrust on the walls of the material to be cut.

Figure 18

The FK350 uses discs with positive cutting

angles for cutting solid materials and with

negative cutting angles for cutting hollow

profiles. This is because, as a result of the high

cutting speeds (3400 rpm), even with

non-ferrous materials the tool ”strikes” against

the wall of the profile to be cut several times,

thus requiring a cutting edge with a larger

resistant section.

Figure 20

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Troubleshooting – Blade and Cutting Problems

Problem

Probable Cause

Solution

Incorrect lubricant/coolant fluid Ensure proper coolant flow.

Check the cutting speed, feed speed and air pressure

parameters and the type of blade you are using.

Material too hard

With a new blade it is necessary to start cutting at half

feeding speed. After the wearing--in period (a cutting

surface of about 300 cm2 for hard materials and about

1000 cm2 for soft materials) the cutting and feed

speeds can be brought up to normal values

Disc not worn--in correctly

Disc with excessively fine

tooth pitch

The swarf wedges into the bottom of the teeth causing

excessive pressure on the teeth themselves

Teeth breaking

The surface of the cut may have undergone work

hardening. When starting work again, use a lower

cutting speed and head feed speed. A tooth from the

old blade may be left in the cut: check and remove

before starting work again.

New blade inserted in a

partially completed cut

Any movement of the work piece during cutting can

cause broken teeth: check the vise, jaws and clamping

pressure.

Work piece not clamped firmly

in place

The blade runs over the material without removing it:

increase feed speed.

Feed speed too slow

Cutting pressure too high

Blade speed too high

Reduce cutting pressure.

The teeth slide over the material without cutting it:

reduce the blade speed.

Check the coolant level and clean coolant lines and

nozzles.

Insufficient coolant

Rapid tooth wear

Incorrect fluid concentration

Check and use the correct concentration.

The materials may present altered zones either on the

surface, such as oxides or sand, or in section, such as

under-cooled inclusions. These zones, which are

much harder than the blade, cause the teeth to break:

discard or clean these materials.

Material defective

Feed speed too high

Reduce blade speed.

Teeth in contact with material

before starting the cut

Always check the position of the blade before starting

a new job.

Broken blade

Check the coolant level and clean coolant lines and

nozzles.

Insufficient coolant

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting – Machine Fault & Operating Problems

Problem

Probable Cause

Solution

Check: the phases; the cables; the plug; the socket.

Also check that the motor connections are in place.

Electrical power supply

Check that the voltages are present both on the input

and output. Otherwise replace.

Transformer

Contactor

Check that the phases in it are present both on the

input and output, that it is not jammed, that it closes

when powered and that it is not causing short circuits.

Change if any of these problems are found.

Spindle motor will not

turn

Make sure it is closed, ie check that the phases are

present in input and output that it is not causing short

circuits and responds when the reset coil is closed. If it

has tripped to protect the motor, check the amperage

setting, reset, and check the motor. Change if

necessary.

Thermal relay

Check that it has not burnt out, that it turns freely and

that there is no moisture in the connection terminal

board box. The winding can be rewound or replaced.

Motor

Make sure the valve is operating correctly, replace if

necessary.

Cutting Vise Valve

Compressed air supply hose

Vise cylinder

For SX version: Cutting

vise will not close or will

not open

Check that air is not leaking through the cylinder seals.

Check the hose is not kinked or blocked. Remove the

obstruction. Replace cylinder or cylinder seals

Parts

Ordering Replacement Parts

To order parts or reach our service department, call 1-800-274-6848 between 7:30am and 5:30pm (CST),

Monday through Friday. Having the Model Number and Serial Number of your machine available when

you call will allow us to serve you quickly and accurately.

Download from Www.Somanuals.com. All Manuals Search And Download.

Head Assembly – FK350 & FK350-SX

Index No. Part No.

Description

Size

Qty

1 ...............FK350-201 ...............Head Body ........................................................... .................................... 1

2 ...............FK350-202 ...............Spindle ................................................................. .................................... 1

3 ...............FK350-203 ...............Spindle Housing................................................... .................................... 1

4 ...............FK350-204 ...............Cutter Cap............................................................ .................................... 1

5 ...............FK350-205 ...............Cutter Cap Pin ..................................................... .................................... 2

6 ...............FK350-206 ...............Stopper Ring........................................................ .................................... 1

7 ...............FK350-207 ...............Spring Block......................................................... .................................... 1

8 ...............FK350-208 ...............Tension Bolt......................................................... .................................... 1

9 ...............FK350-209 ...............Belleville Spring ................................................... .................................... 4

10 .............FK350-210 ...............Taper Shaft .......................................................... .................................... 1

11 .............FK350-211 ...............Worm Wheel ........................................................ .................................... 1

12 .............FK350-212 ...............Worm Shaft .......................................................... .................................... 1

13 .............FK350-213 ...............36NTGear ............................................................ .................................... 1

14 .............FK350-214 ...............21NTGear ............................................................ .................................... 1

15 .............FK350-215 ...............Collar A ................................................................ .................................... 1

16 .............FK350-216 ...............Collar B ................................................................ .................................... 1

17 .............FK350-217 ...............Bearing Cover...................................................... .................................... 1

18 .............FK350-218 ...............Handle.................................................................. .................................... 1

19 .............FK350-219 ...............Handle Switch...................................................... .................................... 1

21 .............BB-32007.................Tapered Roller Bearing........................................#32007........................ 1

22 .............BB-32008.................Tapered Roller Bearing........................................#32008........................ 1

23 .............FK350-223 ...............Retainer................................................................ .................................... 1

24 .............FK350-224 ...............Tooth Washer....................................................... .................................... 1

25 .............FK350-225 ...............Retainer Nut......................................................... .................................... 1

26 .............FK350-226 ...............Retainer Nut......................................................... .................................... 1

27 .............FK350-227 ...............Tooth Washer....................................................... .................................... 1

28 .............FK350-228 ...............Tooth Washer....................................................... .................................... 1

29 .............FK350-229 ...............Retainer Nut......................................................... .................................... 1

30 .............FK350-230 ...............Flat Key................................................................8x7x42mm .................. 1

31 .............FK350-231 ...............Flat Key................................................................8x7x27mm .................. 1

32 .............FK350-232 ...............O-Ring.................................................................. .................................... 1

33 .............FK350-233 ...............O-Ring..................................................................P8................................ 1

34 .............FK350-234 ...............Pin........................................................................5mm Dia. x 28............. 2

35 .............TS-1540071 .............Hex Nut ................................................................M10............................. 2

36 .............FK350-236 ...............Needle Roller Bearing..........................................BK3026....................... 1

37 .............BB-51206.................Thrust Bearing .....................................................#51206........................ 1

38 .............BB-6206...................Deep Groove Ball Bearing ...................................#6206.......................... 1

39 .............FK350-239 ...............Motor 220V........................................................... .................................... 1

.................FK350-239-4............Motor 440V........................................................... .................................... 1

40 ............. .................................Saw Blade............................................................ .................................... 1

41 .............FK350-241 ...............Stopper................................................................. .................................... 1

42 .............FK350-242 ...............Oil Sight Glass ..................................................... .................................... 1

43 .............TS-1504051 .............Socket Head Cap Screw M8x25.......................... .................................... 2

44 .............TS-1504041 .............Socket Head Cap Screw M8x20.......................... .................................... 4

45 .............TS-1504131 .............Socket Head Cap Screw M8x70.......................... .................................... 1

46 .............FK350-246 ...............Oil Plug................................................................. .................................... 1

47 .............TS-223E451.............Socket Head Cap Screw M20x45........................ .................................... 1

48 .............FK350-248 ...............Oil Plug................................................................. .................................... 1

49 .............FK350-249 ...............Oil Plug................................................................. .................................... 1

50 .............TS-1504061 .............Socket Head Cap Screw M8x30.......................... .................................... 2

51 .............TS-1492051 .............Hex Cap Screw M12x50 ...................................... .................................... 4

52 .............TS-154012 ...............Hex Nut M20........................................................ .................................... 1

53 .............TS-1540061 .............Hex Nut M8.......................................................... .................................... 1

54 .............TS-2361201 .............Lock Washer M20................................................ .................................... 1

55 .............TS-2361121 .............Lock Washer M12................................................ .................................... 4

Download from Www.Somanuals.com. All Manuals Search And Download.

Head Assembly – FK350 & FK350-SX

Download from Www.Somanuals.com. All Manuals Search And Download.

Power Feed Assembly – FK350-SX

Index No. Part No.

Description

Size

Qty

1 ...............FK350SX-701 ..........Spring Bracket A.................................................. .................................... 1

2 ...............FK350SX-702 ..........Spring Bracket B.................................................. .................................... 1

3 ...............FK350SX-703 ..........Converter Bracket................................................ .................................... 1

4 ...............FK350SX-704 ..........Cylinder Bracket................................................... .................................... 1

5 ...............FK350SX-705 ..........Hinge Bolt............................................................. .................................... 2

6 ...............FK350SX-706 ..........Limit Rod.............................................................. .................................... 1

7 ...............FK350SX-707 ..........Limit Dog.............................................................. .................................... 2

8 ...............FK350SX-708 ..........Knuckle Pin.......................................................... .................................... 1

9 ...............CK350SX-709..........Thread Extension................................................. .................................... 2

11 .............FK350SX-711 ..........Cylinder ............................................................... .................................... 1

12 .............FK350SX-712 ..........Converter ............................................................. .................................... 1

13 .............FK350SX-713 ..........Limit Switch ......................................................... .................................... 2

14 .............FK350SX-714 ..........Elbow Push Fitting ...............................................PT 3/8 ......................... 3

15 .............FK350SX-715 ..........Compression Fitting............................................. .................................... 1

16 .............TS-1504061 .............Socket Head Cap Screw......................................M8x30......................... 4

17 .............TS-1551061 .............Lock Washer........................................................M8............................... 4

18 .............TS-1491041 .............Hex Cap Screw....................................................M10x30....................... 4

19 .............TS-2361101 .............Lock Washer........................................................M10............................. 4

20 .............TS-1506111 .............Socket Head Cap Screw......................................M12x70....................... 4

21 .............TS-1503051 .............Socket Head Cap Screw......................................M6x20......................... 3

22 .............FK350SX-722 ..........Handle.................................................................. .................................... 2

23 .............FK350SX-723 ..........Snap Ring ............................................................S12.............................. 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Power Feed Assembly – FK350-SX

Download from Www.Somanuals.com. All Manuals Search And Download.

Stock Stop Assembly

Index No. Part No.

Description

Size

Qty

1 ...............FK350-501 ...............Block .................................................................... .................................... 1

2 ...............FK350-502 ...............Shaft..................................................................... .................................... 1

3 ...............FK350-503 ...............Stop Rod .............................................................. .................................... 1

4 ...............FK350-504 ...............Scale (Inch).......................................................... .................................... 1

6 ...............FK350-506 ...............Handle..................................................................M8x30......................... 2

7 ...............FK350-505 ...............Rivet..................................................................... .................................... 2

Download from Www.Somanuals.com. All Manuals Search And Download.

Stand Assembly – FK350

Index No. Part No.

Description

Size

Qty

1 ...............FK350-601 ...............Cabinet Stand ...................................................... .................................... 1

2 ...............FK350-602 ...............Coolant Pump ...................................................... .................................... 1

3 ...............FK350-603 ...............Cam Switch.......................................................... .................................... 1

4 ...............FK350-604 ...............Magnetic Switch................................................... .................................... 1

5 ...............FK350-605 ...............Overload Relay .................................................... .................................... 1

6 ...............FK350-606 ...............Lighted Selector Switch ....................................... .................................... 1

7 ...............TS-1502051 .............Socket Head Cap Screw......................................M5x20......................... 4

8 ...............TS-1551031 .............Lock Washer........................................................M5............................... 4

9 ...............FK350-609 ...............Cable Lock........................................................... .................................... 3

10 .............FK350-610 ...............Rear Cover........................................................... .................................... 1

11 .............TS-1503021 .............Socket Head Cap Screw......................................M6x10......................... 4

12 .............FK350-612 ...............Tapered Plug .......................................................PT1/4 .......................... 1

13 .............FK350-613 ...............Coolant Gauge..................................................... .................................... 1

14 .............TS-1502051 .............Socket Head Cap Screw......................................M5x20......................... 2

Download from Www.Somanuals.com. All Manuals Search And Download.

Stand Assembly – FK350-SX

Index No. Part No.

Description

Size

Qty

1 ...............FK350SX-601 ..........Cabinet Stand ...................................................... .................................... 1

2 ...............FK350SX-602 ..........Foot Switch (Optional) ......................................... .................................... 1

3 ...............FK350-603 ...............Cam Switch.......................................................... .................................... 1

4 ...............FK350-604 ...............Magnetic Switch................................................... .................................... 1

5 ...............FK350SX-605 ..........Overload Relay .................................................... .................................... 1

7 ...............FK350SX-607 ..........Control Box Bracket............................................. .................................... 1

8 ...............FK350SX-608 ..........Control Box .......................................................... .................................... 1

9 ...............FK350-609 ...............Cable Lock........................................................... .................................... 6

10 .............FK350-610 ...............Rear Cover........................................................... .................................... 1

11 .............TS-1503021 .............Socket Head Cap Screw......................................M6x10......................... 4

12 .............FK350-612 ...............Tapered Plug .......................................................PT1/4 .......................... 1

13 .............FK350-613 ...............Coolant Gauge..................................................... .................................... 1

14 .............TS-1502051 .............Socket Head Cap Screw......................................M5x20......................... 2

15 .............FK350SX-615 ..........Lighted Push Button Switch................................. .................................... 1

16 .............FK350SX-616 ..........Lighted Push Button Switch................................. .................................... 1

17 .............FK350SX-617 ..........Emergency Switch ............................................... .................................... 1

18 .............FK350SX-618 ..........Selector Switch .................................................... .................................... 2

19 .............FK350SX-619 ..........Selector Switch .................................................... .................................... 1

20 .............FK350SX-620 ..........Flow Control Valve............................................... .................................... 1

21 .............TS-1504041 .............Socket Head Cap Screw......................................M8x20......................... 2

22 .............TS-1551061 .............Lock Washer........................................................M8............................... 2

23 .............FK350SX-623 ..........Flexible Connector............................................... .................................... 2

24 .............FK350SX-624 ..........Transformer.......................................................... .................................... 1

25 .............FK350SX-625 ..........Circuit Breaker ..................................................... .................................... 1

26 .............FK350SX-626 ..........Fuse .....................................................................5A, 30mm ................... 2

27 .............FK350SX-627 ..........Fuse Holder.......................................................... .................................... 1

28 .............FK350SX-628 ..........Relay.................................................................... .................................... 5

29 .............FK350SX-629 ..........Relay Socket........................................................ .................................... 5

30 .............FK350SX-630 ..........Relay.................................................................... .................................... 1

31 .............FK350SX-631 ..........Relay Socket........................................................ .................................... 1

32 .............FK350SX-632 ..........Timer Relay.......................................................... .................................... 2

33 .............FK350SX-633 ..........Terminal Block ..................................................... .................................. 30

34 .............FK350SX-634 ..........Air Unit ................................................................. .................................... 1

35 .............FK350SX-635 ..........Elbow Push Fitting ...............................................PT3/8 .......................... 4

36 .............FK350SX-636 ..........Elbow Push Fitting ...............................................PT1/4 .......................... 1

37 .............FK350SX-637 ..........Elbow Push Fitting ...............................................PT1/8 .......................... 1

38 .............FK350SX-638 ..........Nipple Push Fitting...............................................PT3/8 .......................... 4

39 .............FK350SX-639 ..........Nipple...................................................................PT3/8 .......................... 2

40 .............FK350SX-640 ..........Reducer................................................................PT3/8x1/4 ................... 1

41 .............FK350SX-641 ..........T-Union ................................................................PT3/8 .......................... 2

42 .............FK350SX-642 ..........Solenoid Valve..................................................... .................................... 1

43 .............FK350SX-643 ..........Solenoid Valve..................................................... .................................... 1

44 .............FK350SX-644 ..........Socket Head Cap Screw......................................M4x60......................... 3

45 .............TS-1550021 .............Flat Washer..........................................................M4............................... 3

46 .............FK350SX-646 ..........Silencer ................................................................PT3/8 .......................... 4

47 .............FK350SX-647 ..........Pipe...................................................................... .................................... 1

48 .............FK350SX-648 ..........Ball Valve ............................................................. .................................... 1

49 .............FK350SX-649 ..........Quick Coupler ...................................................... .................................... 1

50 .............FK350SX-650 ..........Pressure Gauge................................................... .................................... 1

51 .............FK350-602 ...............Coolant Pump ...................................................... .................................... 1

52 .............TS-1502051 .............Socket Head Cap Screw......................................M5x20......................... 4

53 .............TS-1551031 .............Lock Washer........................................................M5............................... 4

Download from Www.Somanuals.com. All Manuals Search And Download.

Stand Assembly – FK350-SX

Download from Www.Somanuals.com. All Manuals Search And Download.

Base Assembly – FK350

Index No. Part No.

Description

Size

Qty

1 ...............FK350-101 ...............Base..................................................................... .................................... 1

2 ...............FK350-102 ...............Hinge Body........................................................... .................................... 1

3 ...............FK350-103 ...............Locking Mount...................................................... .................................... 1

4 ...............FK350-104 ...............Release Handle ................................................... .................................... 1

5 ...............FK350-105 ...............Pin........................................................................ .................................... 1

6 ...............FK350-106 ...............Coil Spring............................................................ .................................... 1

7 ...............FK350-107 ...............Scale .................................................................... .................................... 1

8 ...............FK350-108 ...............Pivot Shaft............................................................ .................................... 1

9 ...............FK350-109 ...............Spring Bracket A.................................................. .................................... 1

10 .............FK350-110 ...............Spring Bracket B.................................................. .................................... 1

11 .............FK350-111 ...............Return Spring....................................................... .................................... 1

12 .............FK350-112 ...............Chip Screen ......................................................... .................................... 1

13 .............TS-1505031 .............Socket Head Cap Screw......................................M10x25....................... 2

14 .............TS-1551071 .............Lock Washer........................................................M10............................. 2

15 .............TS-1504041 .............Socket Head Cap Screw......................................M8x20......................... 2

16 .............TS-1504101 .............Socket Head Cap Screw......................................M8x50......................... 2

17 .............TS-1491041 .............Hex Cap Screw....................................................M10x30....................... 2

18 .............TS-2361101 .............Lock Washer........................................................M10............................. 2

19 .............TS-1504021 .............Socket Head Cap Screw......................................M8x12......................... 2

20 .............TS-1490041 .............Hex Cap Screw....................................................M8x25......................... 1

21 .............TS-223A911.............Socket Head Cap Screw......................................M12x100..................... 2

22 .............FK350-122 ...............Pipe...................................................................... .................................... 1

23 .............FK350-123 ...............Pin........................................................................10mm Dia. x 22........... 3

24 .............FK350-124 ...............Grease Fitting ......................................................PT 1/8 ......................... 2

Download from Www.Somanuals.com. All Manuals Search And Download.

Base Assembly – FK350

Download from Www.Somanuals.com. All Manuals Search And Download.

Base Assembly – FK350-SX