24" (61 CM) GAS WASHER/DRYER INSTALLATION INSTRUCTIONS
TableofContents
WASHER/DRYER SAFETY ..............................1
Remove Foam Packing..................................8
Connect Drain Hose.......................................8
Connect Inlet Hoses ......................................8
Secure Drain Hose.........................................9
Plan Vent System...........................................9
Install Vent System ......................................11
Level Washer/Dryer......................................11
Make Gas Connection.................................11
Connect Vent ...............................................11
Complete Installation...................................12
INSTALLATION INSTRUCTIONS ....................2
Tools and Parts..............................................2
Alternate Parts ...............................................3
Location Requirements..................................3
Drain System..................................................4
Electrical Requirements.................................5
Gas Supply Requirements.............................5
Venting Requirements....................................6
Install Leveling Legs.......................................7
WASHER/DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
DANGER
You can be killed or seriously injured if you don't
instructions.
follow
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
When discarding or storing your old clothes dryer, remove the door.
SAVE THESE INSTRUCTIONS
W10222384A
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts supplied:
Remove parts package from the washer basket. Check that all
parts were included.
LocationRequirements
WARNING
A
B
C
D
E
Explosion Hazard
A. Rear leveling legs (2)
B. Front leveling legs (2)
C. Drain hose
D. Plastic strap
E. Silver double-wire hose clamp
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Failure to do so can result in death, explosion, or fire.
Parts needed:
Check local codes and with gas supplier, check existing gas
supply, electrical supply and venting, and read “Electrical
Requirements,” “Gas Supply Requirements,” and “Venting
Requirements” before purchasing parts.
Mobile home installations require special parts (listed following)
available for purchase from the dealer from whom you purchased
your dryer. For further information, please reference the
“Assistance or Service” section of the Washer/Dryer User
Instructions.
You will need
A location that allows for proper exhaust installation. A gas
washer/dryer must be exhausted to the outdoors. See
“Venting Requirements.”
A grounded electrical outlet located within 2 ft (610 mm) of
either side of the washer/dryer. See “Electrical Requirements.”
A sturdy floor to support the washer/dryer weight (washer/
dryer, water and load) of 500 lbs (226.8 kg).
Mobile Home Installation Kit. Ask for Part Number 346764.
A level floor with a maximum slope of 1" (25 mm) under entire
washer/dryer. Clothes may not tumble properly and automatic
sensor cycles may not operate correctly if washer/dryer is not
level. Installing on carpet is not recommended.
Metal exhaust system hardware.
AlternateParts
A water heater set to deliver 120°F (49°C) water to the washer.
Your installation may require additional parts. For information on
ordering, please refer to the toll free phone numbers on the front
page of the Washer/Dryer User Instructions.
Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of 5-100 psi
(34.5-689.6 kPa).
If You Have
You Will Need to Buy
The washer/dryer must not be installed or stored in an area where
it will be exposed to water and/or weather.
Do not operate your washer in temperatures at or below
32ºF (0ºC). Some water can remain in the washer and can cause
damage in low temperatures. See “Washer/Dryer Care” in the
Washer/Dryer User Instructions for winterizing information.
Do not operate your dryer at temperatures below 45°F (7°C). At
lower temperatures, the dryer might not shut off at the end of an
automatic cycle. This can result in longer drying times.
Laundry tub or
standpipe taller than
96" (2.4 m)
Sump pump system (if not already
available)
1" (25 mm) diameter
standpipe
2" (51 mm) diameter to 1" (25 mm)
diameter standpipe adapter, Part
Number 3363920
Overhead sewer
Floor drain
Standard 20 gal. (76 L) 34" (864 mm)
tall drain tub or utility sink and sump
pump (available from local plumbing
suppliers)
Check code requirements. Some codes limit, or do not permit,
installation of the washer/dryer in garages, closets, mobile homes,
or sleeping quarters. Contact your local building inspector.
NOTE: No other fuel-burning appliance can be installed in the
same closet as a dryer.
Siphon break, Part Number 285320,
additional drain hose, Part Number
285702 and connector kit,
Installation Clearances
The location must be large enough to allow the dryer door
Part Number 285442
to open fully.
Drain hose too short
Lint clogged drain
Drain hose, Part Number 285664 and
connector kit, Part Number 285442
Drain protector, Part Number 367031
Water faucets
beyond reach of fill
hoses
2 longer water fill hoses:
6 ft (1.8 m) Part Number 76314,
10 ft (3.0 m) Part Number 350008
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Mobile home installations require:
Washer/Dryer Dimensions
Metal exhaust system hardware, which is available for
purchase from your dealer.
153
(391 mm)
⁄
8
"
Mobile Home Installation Kit Part Number 346764. See “Tools
and Parts” section for information on ordering.
Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a
nearby window) should be at least twice as large as the dryer
exhaust opening.
71 ¾"
(1822 mm)
DrainSystem
The washer/dryer can be installed using the standpipe drain
system (floor or wall), the laundry tub drain system, or the floor
drain system. Select the drain hose installation method you need.
See “Alternate Parts.”
321
(816 mm)
⁄
8
"
Standpipe drain system - wall or floor (views A & B)
*27 ¼"
(692 mm)
The standpipe drain requires a minimum diameter standpipe of
2" (51 mm). The minimum carry-away capacity can be no less than
17 gal. (64 L) per minute. A 2" (51 mm) diameter to 1" (25 mm)
diameter standpipe adapter kit is available. See “Alternate Parts.”
The top of the standpipe must be at least 39" (991 mm) high and no
higher than 96" (2.4 m) from the bottom of the washer.
23 7
(606 mm)
⁄
8
"
*Most installations require a minimum 5" (127 mm) clearance
behind the dryer for the exhaust vent with elbow. See “Venting
Requirements.”
Installation spacing for recessed area or closet installation
The following spacing dimensions are recommended for this
washer/dryer. This washer/dryer has been tested for spacing of 0"
(0 mm) clearance on the sides, rear and top. Recommended
spacing should be considered for the following reasons:
Additional spacing should be considered for ease of
installation and servicing.
39"
(991 mm)
Additional clearances might be required for wall, door,
and floor moldings.
Additional spacing on all sides of the washer/dryer is
recommended to reduce noise transfer.
B
A
For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top
of the laundry tub must be at least 34" (864 mm) above the floor
and no higher than 96" (2.4 m) from the bottom of the washer.
1"
(25 mm)
3" (76 mm)
48 in.2
Floor drain system (view D)
The floor drain system requires a siphon break that may be
purchased separately. See “Alternate Parts.”
(310 cm2)
The siphon break must be a minimum of 28" (711 mm) from the
bottom of the washer. Additional hoses might be needed.
24 in.2
(155 cm2)
3" (76 mm)
7
1
"
23
⁄
8
"
1"
5"**
1"*
27¼"
(25 mm)
(606 mm)
(25 mm)
(127 mm)
(25 mm)
(692 mm)
A
B
C
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
34"
(864 mm)
*Required spacing
**Rear clearance may be 0" (0 mm) when house exhaust system
is lined up directly with dryer exhaust.
C
D
Mobile Home - Additional Installation Requirements
This washer/dryer is suitable for mobile home installations.
The installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ElectricalRequirements
GasSupply Requirements
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical
supply is required. A time-delay fuse or circuit breaker is
recommended. It is also recommended that a separate circuit
serving only this appliance be provided.
To minimize possible shock hazard, the cord must be plugged
into a mating, 3 prong, grounding-type outlet, grounded in
accordance with local codes and ordinances. If a mating
outlet is not available, it is the personal responsibility and
obligation of the customer to have the properly grounded
outlet installed by a qualified electrician.
Gas Type
Natural Gas:
This washer/dryer is equipped for use with Natural gas. It is
design-certified by CSA International for LP (propane or butane)
gases with appropriate conversion.
IMPORTANT: The washer/dryer must be electrically grounded
in accordance with local codes, or in the absence of local
codes, with the National Electrical Code, ANSI/NFPA 70.
Your washer/dryer must have the correct burner for the type of
gas in your home. Burner information is located on the rating
plate in the door well of your dryer. If this information does not
agree with the type of gas available, contact your dealer or call
the phone numbers referenced on the front page of the
Washer/Dryer User Instructions.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
Do not ground to a gas pipe.
Check with a qualified electrician if you are not sure the
washer/dryer is properly grounded.
LP gas conversion:
Conversion must be made by a qualified technician.
No attempt shall be made to convert the appliance from the gas
specified on the model/serial rating plate for use with a different
gas without consulting your gas company.
Do not have a fuse in the neutral or ground circuit.
GROUNDING INSTRUCTIONS
For a grounded, cord-connected washer/dryer:
This washer/dryer must be grounded. In the event of
malfunction or breakdown, grounding will reduce the risk of
electric shock by providing a path of least resistance for
electric current. This washer/dryer is equipped with a cord
having an equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate outlet
that is properly installed and grounded in accordance with
all local codes and ordinances.
Gas supply line
Must include 1⁄8" NPT minimum plugged tapping accessible
for test gauge connection, immediately upstream of the gas
supply connection to the dryer (see illustration).
½" IPS pipe is recommended.
3
⁄8" approved aluminum or copper tubing is acceptable for
lengths under 20 ft (6.1 m) if local codes and gas supplier
permit.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative or
personnel if you are in doubt as to whether the washer/dryer
is properly grounded. Do not modify the plug provided with
the washer/dryer: if it will not fit the outlet, have a proper
outlet installed by a qualified electrician.
If you are using Natural gas, do not use copper tubing.
Lengths over 20 ft (6.1 m) should use larger tubing and a
different size adapter fitting.
Gas supply line coupling must be 34" (864 mm) to 37"
(940 mm) from the floor.
If your washer/dryer has been converted to use LP gas, 3⁄8" LP
compatible copper tubing can be used. If the total length of
the supply line is more than 20 ft (6.1 m), use larger tubing.
SAVE THESE INSTRUCTIONS
NOTE: Pipe-joint compounds that resist the action of LP gas
must be used. Do not use TEFLON®† tape.
†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Must include a shutoff valve:
An individual shutoff valve must be installed within
six (6) feet (1.8 m) of the washer/dryer in accordance with
the National Fuel Gas Code, ANSI Z223.1/NFPA 54. The
location should be easy to reach for opening and closing.
Venting Requirements
WARNING
A
B
C
Fire Hazard
Use a heavy metal vent.
D
Do not use a plastic vent.
Do not use a metal foil vent.
A. Gas shutoff valve
B. 1⁄8" NPT minimum plugged tapping
C. ½" NPT gas supply line
Failure to follow these instructions can result in death
or fire.
D. Gas supply line coupling 34" (864 mm) min.
to 37" (940 mm) max. from floor
WARNING: To reduce the risk of fire, this washer/dryer
MUST BE EXHAUSTED OUTDOORS.
IMPORTANT: Observe all governing codes and ordinances.
Burner input requirements:
The dryer exhaust must not be connected into any gas vent,
chimney, wall, ceiling, attic, crawlspace, or a concealed space
of a building.
Elevations up to 10,000 ft (3,048 m):
The design of this washer/dryer is certified by CSA
International for use at altitudes up to 10,000 ft (3,048 m)
above sea level at the Btu rating indicated on the model/serial
number plate. Burner input adjustments are not required when
the dryer is operated up to this elevation.
If using an existing vent system
Clean lint from the entire length of the system and make sure
exhaust hood is not plugged with lint.
Elevations above 10,000 ft (3,048 m):
Replace any plastic or metal foil vent with rigid or flexible
heavy metal vent.
When installed above 10,000 ft (3,048 m), a 4% reduction of
the burner Btu rating shown on the model/serial number plate
is required for each 1,000 ft (305 m) increase in elevation.
Review Vent system chart. Modify existing vent system if
necessary to achieve the best drying performance. Only rigid
or flexible metal vent shall be used for exhausting.
Gas supply pressure testing
The washer/dryer must be disconnected from the gas supply
piping system during pressure testing at pressures greater
than ½ psi.
If this is a new vent system
Vent material
Use a heavy metal vent. Do not use plastic or metal foil vent.
Dryer gas connection
4" (102 mm) heavy metal exhaust vent and clamps must be
used. DURASAFE™ venting products are recommended.
This washer/dryer is equipped with its own permanent,
flexible gas connector, design-certified by CSA International,
for connecting the washer/dryer to the gas supply line.
4"
102 mm
4" (102 mm) heavy metal exhaust vent
DURASAFE™ vent products can be purchased from your
dealer or by calling Whirlpool Parts and Accessories. For more
information, see the “Assistance or Service” section of the
Washer/Dryer User Instructions.
Flexible gas connector
Rigid metal vent
For best drying performance, rigid metal vents are
recommended.
Rigid metal vent is recommended to avoid crushing and
kinking.
Flexible metal vent
Flexible metal vents are acceptable only if accessible for
cleaning.
Flexible metal vent must be fully extended and supported
when the dryer is in its final location.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove excess flexible metal vent to avoid sagging and
kinking that may result in reduced airflow and poor
performance.
Install LevelingLegs
Do not install flexible metal vent in enclosed walls, ceilings,
or floors.
WARNING
Excessive Weight Hazard
The total length of flexible metal vent should not exceed
73⁄4 ft (2.4 m).
Elbows
45° elbows provide better airflow than 90° elbows.
Use two or more people to move and install
washer/dryer.
Failure to do so can result in back or other injury.
To protect the floor, use a large flat piece of cardboard from the
shipping carton. Gently place the washer/dryer on its side, on the
cardboard.
Install the rear leveling legs
1. Push legs into holes in rear corners until they snap into place.
Good
Better
Clamps
Use clamps to seal all joints.
Exhaust vent must not be connected or secured with screws
or other fastening devices that extend into the interior of the
duct and catch lint. Do not use duct tape.
2. Check adjustability of rear legs by pushing in one leg. The
other leg should come out. Check both legs. If they do not
move freely, repeat Step 1.
Clamp
Install the front leveling legs
1. Examine the front leveling legs. Find the diamond marking.
Exhaust
2. Screw front legs by hand, into the holes in the triangular
braces in the front corners. Use wrench to finish turning the
legs until the diamond marking is no longer visible.
Recommended hood styles are shown here.
B
A
4"
(102 mm)
4"
(102 mm)
A. Louvered hood style
B. Box hood style
3. Slowly stand the washer/dryer upright.
The angled hood style (shown here) is acceptable.
For mobile home use
Washer/dryers with gas dryers must be securely fastened
to the floor.
4"
(102 mm)
2½"
(64 mm)
An exhaust hood should cap the vent to keep rodents and
insects from entering the home.
Mobile home installations require a Mobile Home Installation Kit.
See “Tools and Parts” section for information on ordering.
Exhaust hood must be at least 12" (305 mm) from the ground
or any object that may be in the path of the exhaust (such as
flowers, rocks or bushes, snow line, etc.).
Do not use an exhaust hood with a magnetic latch.
Improper venting can cause moisture and lint to collect
indoors, which may result in:
Moisture damage to woodwork, furniture, paint, wallpaper,
carpets, etc.
Housecleaning problems and health problems.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
For laundry tub or standpipe drain systems
1. Make sure drain hose form is in correct position.
Remove FoamPacking
1. Open the washer lid. The latch under the dryer will keep the
lid open.
A
2. Pull the foam packing ring out of the washer.
A. Drain hose form
NOTE: Keep the foam ring and use it when transporting your
washer/dryer. This packing material is used to keep the washer
tub stable during transport.
2. Put the hooked end of drain hose into laundry tub or
standpipe. Rotate hook to eliminate kinks.
To keep drain water from going back into the washer:
Do not force excess drain hose into standpipe. Hose
should be secure but loose enough to provide a gap
for air.
ConnectDrainHose
Proper connection of the drain hose protects your floors from
damage due to water leakage. To keep the drain hose from
coming off or leaking, it must be installed according to the
following instructions:
Do not lay excess hose on the bottom of the laundry tub.
For use with floor drain
Do not install the drain hose form onto the corrugated drain hose.
You may need additional parts. See Floor drain under “Tools and
Parts.”
IMPORTANT: To ensure proper installation, this procedure must
be followed exactly.
1. Check the drain hose to see whether it is the proper length.
2. Wet the inside of the straight end of the drain hose with tap
water.
ConnectInletHoses
IMPORTANT: Do not use any lubricant other than water.
1. Insert a new flat washer into each end of the inlet hoses
(not provided). Firmly seat the washers in the couplings.
3. Squeeze ears of the silver double-wire clamp with pliers to
open. Place clamp over the straight end of the drain hose
¼" (6.4 mm) from the end.
A
B
¼"
(6.4 mm)
A. Coupling
B. Washer
Connect the inlet hoses to the water faucets
Make sure the washer basket is empty.
1. Attach hose to the hot water faucet. Screw on coupling by
4. Open clamp. Twist hose back and forth while pushing onto
drain connector on the side of the washer/dryer. Continue until
hose contacts the ribbed stops on the cabinet.
hand until it is seated on the washer.
2. Attach hose to the cold water faucet. Screw on coupling by
hand until it is seated on the washer.
3. Using pliers, tighten the couplings with an additional two-
thirds turn.
NOTE: Do not overtighten or use tape or sealants on the valve.
Damage to the valves can result.
5. Place clamp over the area marked “CLAMP.” Release clamp.
Clear the water lines
Run water through both faucets and inlet hoses, into a laundry
tub, drainpipe, or bucket to get rid of particles in the water
lines that might clog the inlet valve screens.
Check the temperature of the water to make sure that the hot
water hose is connected to the hot water faucet and that the
cold water hose is connected to the cold water faucet.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect the inlet hoses to the washer
1. Attach the hot water hose to the bottom inlet valve. Attaching
the hot water hose first makes it easier to tighten connection
with pliers.
SecureDrain Hose
1. Move the washer/dryer to its final location and remove any
cardboard used to move the washer/dryer.
2. Locate the plastic strap included in the parts package.
2. Screw on coupling by hand until it is seated on the washer.
3. Using pliers, tighten the couplings with an additional two-
thirds turn.
NOTE: Do not overtighten or use tape or sealants on the valve.
Damage to the valves can result.
Plastic strap
A
B
3. Wrap the drain hose to the laundry tub leg or standpipe with
the plastic strap (A or B below) and secure.
A. Cold water inlet valve (top)
B. Hot water inlet valve (bottom)
A
B
C
4. Attach the cold water hose to the top inlet valve.
5. Screw on coupling by hand until it is seated on the washer.
If the water faucets and the drain standpipe are recessed, put
the hooked end of the drain hose in the standpipe. Tightly
wrap the plastic strap around the water inlet hoses and the
drain hose (C above).
6. Using pliers, tighten the couplings with an additional two-
thirds turn.
NOTE: Do not overtighten or use tape or sealants on the valve.
Damage to the valves can result.
PlanVentSystem
If you are working in a closet or recessed area
Move the washer/dryer into its final location and remove
cardboard from under washer/dryer. Remove the access panel by
removing three Phillips-head screws and one bumper, located at
the top of the access panel. Set panel, screws, and bumper aside.
Complete hookup of water hoses and (on gas models) the flexible
gas connector through the access area. Replace access panel
upon completion of washer/dryer installation.
Choose your exhaust installation type
Recommended exhaust installations
Typical installations vent the dryer from the rear of the washer/
dryer. Other installations are possible.
D
A
E
F
Check for leaks
B
Turn on the water faucets and check for leaks. A small amount
of water might enter the washer. You will drain this water later.
G
NOTE: Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Record hose installation or replacement dates for
future reference.
C
H
If you connect only one water hose, you must cap off the
remaining water inlet port.
A. Dryer
E. Elbow
F. Clamps
G. Elbow
H. Exhaust hood
Periodically inspect and replace hoses if bulges, kinks, cuts,
wear, or leaks are found.
B. Rigid metal or flexible metal vent
C. Clamps
D. Wall
The apparatus must be connected to the water faucets using
the new hoses. Do not use old hoses.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: The following kits for close clearance alternate installations
are available for purchase. Please reference the “Assistance or
Service” section of the Washer/Dryer User Instructions.
Optional exhaust installations
This washer/dryer can be converted to exhaust out the right
or left side. To convert the washer/dryer, use Side Exhaust Kit
Part Number 279823. If your washer/dryer was previously
exhausted from the right or left side, it can be converted to rear
exhaust by using standard offset connections. To cover the hole
in the side, one of the following plugs can be added:
Over-the-Top Installation:
Part Number 4396028
Periscope Installation (For use with dryer vent to wall vent
mismatch):
692790 (white)
3977784 (biscuit)
Part Number 4396037 - 0" (0 mm) to 18" (457 mm) mismatch
Follow the instructions in the kit to install. Kits are available from
the dealer from whom you purchased your washer/dryer.
Part Number 4396011 - 18" (457 mm) to 29" (737 mm)
mismatch
Part Number 4396014 - 29" (737 mm) to 50" (1.27 m)
mismatch
Special provisions for mobile home installations
The exhaust vent must be securely fastened to a noncombustible
portion of the mobile home structure and must not terminate
beneath the mobile home. Terminate the exhaust vent outside.
C
A
B
A. Standard rear offset exhaust installation
B. Rear exhaust for offset close clearance connection
C. Left or right side exhaust installation
Alternate installations for close clearances
Venting systems come in many varieties. Select the type best for
your installation. Three close-clearance installations are shown.
Refer to the manufacturer’s instructions provided with the vent
system.
Determine vent path
Select the route that will provide the straightest and most
direct path outdoors.
Plan the installation to use the fewest number of elbows
and turns.
When using elbows or making turns, allow as much room
as possible.
Bend vent gradually to avoid kinking.
Use the fewest 90° turns possible.
Determine vent length and elbows needed for best drying
performance
Use the Vent system chart below to determine type of vent
material and hood combinations acceptable to use.
A
B
C
NOTE: Do not use vent runs longer than those specified
in the Vent system chart. Exhaust systems longer than those
specified will:
A. Loop system with standard elbows
B. Loop system with one offset and one standard elbow
C. Vent system with one periscope (2" [51 mm] clearance)
Shorten the life of the dryer.
Reduce performance, resulting in longer drying times and
increased energy usage.
The Vent system chart provides venting requirements that will help
to achieve the best drying performance.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Install the adapter on the ½" rigid gas supply pipe using pipe-
Vent system chart
NOTE: Side exhaust installations add a 90º turn inside the dryer.
To determine maximum exhaust length, add one 90º turn to the
chart.
joint compound.
Number of
90º turns
or elbows
Type of Vent
Box or
Louvered
hoods
Angled
hoods
A
B
C
D
E
0
1
2
Rigid metal
Rigid metal
Rigid metal
43 ft (13.1 m)
33 ft (10.1 m)
23 ft (7.0 m)
36 ft (11.0 m)
26 ft (7.9 m)
16 ft (4.9 m)
A. ½" rigid gas supply pipe
B. Use pipe-joint compound.
C. ½" NPT adapter
D. Do not use pipe-joint compound.
E. Flexible gas connector
InstallVentSystem
1. Install exhaust hood. Use caulking compound to seal exterior
wall opening around exhaust hood.
2. Connect vent to exhaust hood. Vent must fit inside exhaust
NOTE: For LP gas connections, you must use pipe-joint
compound resistant to the action of LP gas. Do not use
TEFLON®† tape.
hood. Secure vent to exhaust hood with 4" (102 mm) clamp.
3. Run vent to dryer location. Use the straightest path possible.
See “Determine vent path” in “Plan Vent System.” Avoid 90º
turns. Use clamps to seal all joints. Do not use duct tape,
screws, or other fastening devices that extend into the interior
of the vent to secure the vent, because they can catch lint.
4. Attach the flexible gas connector to the ½" NPT adapter.
Do not use pipe-joint compound for this connection.
There should be a natural loop in the flexible gas connector.
The flexible gas connector must not be twisted, kinked, or
attached with any sharp bends.
LevelWasher/Dryer
Properly leveling your washer/dryer avoids excessive noise and
vibration.
1. Check the levelness of the washer/dryer by placing a level
on the top edge of the washer, first side to side, then front
to back.
5. All connections must be wrench tightened.
6. Open the shutoff valve in the supply. The valve is open when
the handle is parallel to the gas pipe.
A
B
2. If the washer/dryer is not level, prop up the front with a wood
block and adjust the feet up or down as necessary. Remove
wood block and lower washer/dryer. Repeat this step until the
washer/dryer is level.
A. Closed valve
B. Open valve
7. Test all connections by brushing on an approved noncorrosive
leak-detection solution. Bubbles will show a leak. Correct any
leak found.
MakeGasConnection
1. Remove the red cap from the flexible gas connector.
2. Remove the ½" NPT adapter from the flexible gas connector
ConnectVent
(it will be necessary to use two adjustable wrenches).
1. Using a 4" (102 mm) clamp, connect vent to exhaust outlet
in washer/dryer. If connecting to existing vent, make sure the
vent is clean. The vent must fit over the exhaust outlet and
inside the exhaust hood. Make sure the vent is secured to
exhaust hood with a 4" (102 mm) clamp.
2. Move washer/dryer into its final location. Do not crush or kink
vent. Make sure washer/dryer is level.
3. Check that there are no kinks in the flexible gas line.
†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CompleteInstallation
1. Check that all parts are now installed. If there is an extra part,
7. Check that the water faucets are on.
8. Check for leaks around faucets and inlet hoses.
go back through the steps to see which step was skipped.
2. Check that you have all of your tools.
9. Remove the blue protective film on the console and any tape
3. Dispose of/recycle all packaging materials. Keep the plastic
remaining on the washer/dryer.
foam for use if the washer/dryer should be transported.
10. Read the Washer/Dryer User Instructions.
4. Check the washer/dryer’s final location. Be sure the vent is not
11. Wipe the dryer drum interior thoroughly with a damp cloth to
crushed or kinked.
remove any dust.
5. Check that the washer/dryer is level and front leveling feet are
12. To test the washer, measure 1 the normal recommended
⁄2
tight. See “Level Washer/Dryer.”
amount of detergent and pour it into the washer. Close the lid.
Select HEAVY DUTY and pull out the Cycle Control knob.
Allow the washer to complete one whole cycle.
WARNING
13. To test the dryer, set the dryer on a full heat cycle (not an air
cycle) for 20 minutes and start the dryer.
If the dryer will not start, check the following:
Washer/dryer is plugged into a grounded 3 prong outlet.
Start button has been firmly pushed.
Electrical supply is connected.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Household fuses are intact and tight, or circuit breakers
have not tripped.
Dryer door is closed.
14. When the dryer has been running for 5 minutes, open the
dryer door and feel for heat. If you do not feel heat, turn off the
dryer and check to see whether the gas supply line shutoff
valve is open.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
If the gas supply line shutoff valve is closed, open it, then
repeat the 5-minute test as outlined above.
If the gas supply line shutoff valve is open, contact a
qualified technician.
6. Plug into a grounded 3 prong outlet. Turn on power.
W10222384A
© 2008.
Benton Harbor, Michigan 49022
TM DURASAFE is a trademark of Whirlpool, U.S.A.
10/08
Printed in U.S.A.
All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|