COMBO WASHER/DRYER USER INSTRUCTIONS
Table of Contents
ASSISTANCE OR SERVICE.............................1
WASHER/DRYER SAFETY..............................1
WASHER USE...................................................3
DRYER USE ......................................................5
WASHER/DRYER CARE..................................6
WASHER TROUBLESHOOTING.....................8
DRYER TROUBLESHOOTING ......................10
WARRANTY ....................................................12
Assistance or Service
If you need assistance or service, first see the “Troubleshooting”
section. Additional help is available by calling our Customer
Interaction Center at 1-800-253-1301 from anywhere in the
U.S.A., or write:
Write down the following information about your appliance to help
you obtain assistance or service if you ever need it. You will need
to know your complete model number and serial number. You can
find this information on the model and serial number label, located
at the top inside dryer door well.
Crosley Distribution Center
c/o Correspondence Dept.
675 North Main Street
Dealer name____________________________________________________
Serial number __________________________________________________
Address________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Purchase date __________________________________________________
Winston-Salem, NC 27102-2111
To order parts and accessories, call 1-800-442-9991 or visit our
Please include a daytime phone number in your correspondence.
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
WASHER/DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
DANGER
You can be killed or seriously injured if you don't
instructions.
follow
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
8546451
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking Your Vent
Your washer/dryer must be properly installed and vented for the
NOTE: Service calls caused by improper venting will be paid for
by the customer, whether it was a paid installation or self-
installed.
1. Do not use plastic vent or metal foil vent. Use 4 in. (10.2 cm)
metal or flexible metal vent. Do not kink or crush flexible metal
vent. It must be completely extended to allow adequate
exhaust air to flow. Check vent after installation. Refer to your
Installation Instructions for proper length requirements of vent.
dryer to achieve maximum drying efficiency and shorten drying
times. Use the minimum recommended installation clearances
(found in your Installation Instructions) to avoid blocking the flow
of combustion and ventilation air. See the Installation Instructions
for more information.
WARNING
2. Use a 4 in. (10.2 cm) exhaust hood.
3. Use the straightest path possible when routing the vent.
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
4. Use clamps to seal all joints. Do not use duct tape, screws or
other fastening devices that extend into the interior of the vent
to secure vent.
Failure to follow these instructions can result in death
or fire.
5. Clean exhaust vent periodically, depending on use, but at
least every 2 years, or when installing your washer/dryer in a
new location. When cleaning is complete, be sure to follow the
Installation Instructions supplied with your washer/dryer for
final product check.
If the washer/dryer is not properly installed and vented, it will not
be covered under the warranty.
WASHER USE
Loading
For these suggested full-sized loads, set the LOAD SIZE selector to the highest load size setting.
LARGE CAPACITY WASHERS
Heavy Work
Clothes
Mixed Load
Towels
Delicates
Permanent
Press
Knits
2 pair of pants
3 pair of jeans
1 coverall
2 double sheets
4 pillowcases
6 T-shirts
8 bath towels
8 hand towels
10 washcloths
1 bath mat
2 camisoles
1 double sheet
1 tablecloth
1 dress
2 pair of pants
2 blouses
4 shirts
4 slips
6 undergarments
2 sets of sleepwear
1 child’s outfit
3 shirts
6 pair of shorts
2 shirts
1 blouse
4 tops
2 pair of pants
3 shirts
2 pillowcases
2 dresses
2 blouses
6 handkerchiefs
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting Your Washer
Style 1: With Liquid Fabric Softener Dispenser (on some
models)
WARNING
ꢀ
Use only liquid fabric softener in this dispenser. Pour
measured liquid fabric softener into the dispenser.
Softener is added automatically during the rinse portion of
the cycle. Dilute liquid fabric softener by filling the
dispenser with warm water until liquid reaches the
crossbar in the dispenser opening.
Fire Hazard
Never place items in the washer that are dampened
with gasoline or other flammable fluids.
No washer can completely remove oil.
Style 2: Without Liquid Fabric Softener Dispenser (on some
models)
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
ꢀ
In the final rinse ONLY, add fabric softener that has been
diluted with ¹⁄₂ to 1 cup (125 to 250 mL) warm water.
Doing so can result in death, explosion, or fire.
4. Close the washer lid. Washer will not agitate or spin with the
lid open.
1. Measure detergent and pour it into the washer. If desired, add
powdered or liquid color safe bleach. Drop a sorted load of
clothes loosely into your washer.
5. Turn the WATER LEVEL selector to the correct setting for your
wash load and the type of fabric being washed. You may
change the load size or water level selection after the washer
has started filling by turning the selector to a different setting.
6. Set the TEMPERATURE selector to the correct setting for the
type of fabric and soils being washed. Use the warmest water
safe for fabric. Follow garment label instructions.
ꢀ
Load evenly to maintain washer balance. Mix large and
small items. Items should move easily through the wash
water. Overloading can cause poor cleaning.
2. (OPTIONAL) Add Liquid Chlorine Bleach.
Always measure liquid chlorine bleach. Do not guess. Never
use more than 1 cup (250 mL) for a full load. Follow
manufacturer’s directions for safe use. Use a cup with a
pouring spout to avoid spilling.
NOTE: In wash water temperatures colder than 70ºF (21ºC),
detergents do not dissolve well. Soils can be difficult to
remove. Some fabrics can retain wear wrinkles and have
increased pilling (the formation of small lint-like balls on the
surface of garments).
Let the washer fill and begin agitating the load. Add bleach to
the wash cycle so it can be removed in the rinse cycle. Pour
bleach around the agitator, not directly onto the load.
7. Push in the Cycle Control knob and turn it clockwise to the
wash cycle you want. Reduce the wash time when using a
small load size setting. Pull out the Cycle Control knob to start
the washer.
ꢀ
Follow directions on the care labels. Do not use chlorine
bleach on wool, silk, spandex, acetates, or some flame-
retardant fabrics.
NOTE: Undiluted bleach will damage any fabric it touches.
The damage appears as rips, holes, tears, or color loss and
may not show up until several washings later.
3. (OPTIONAL) Add Liquid Fabric Softener.
To stop or restart your washer:
NOTE: Your washer/dryer does not come with a fabric
softener dispenser installed.
ꢀ
To stop the washer at any time, push in the Cycle
Control knob.
To find out whether your model allows fabric softener
dispenser usage and for ordering information, refer to the front
page of this manual or call the dealer from whom you
purchased your washer/dryer. Ask for Part Number 3350834.
ꢀ
To restart the washer, close the lid (if open) and pull out the
Cycle Control knob.
NOTE: Do not spill or drip any fabric softener onto the clothes.
Undiluted fabric softener can stain fabrics. Always dilute fabric
softener with warm water. Too much fabric softener can make
some items (diapers and towels) nonabsorbent. If this
happens, do not use it in every load, or use less of it in each
load.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
DRYER USE
Loading
Load clothes loosely into the dryer. Do not pack the dryer. Allow space for clothes to tumble freely. The following charts show examples
of balanced loads that would allow for proper tumbling.
LARGE CAPACITY DRYER
Heavy Work
Clothes
Mixed Load
Towels
Delicates
Permanent Press
Knits
2 pair of pants
3 pair of jeans
1 coverall
2 double sheets
4 pillowcases
6 T-shirts
8 bath towels
8 hand towels
10 washcloths
1 bath mat
2 camisoles
1 double sheet
1 tablecloth
1 dress
2 pair of pants
2 blouses
4 shirts
4 slips
6 undergarments
2 sets of sleepwear
1 child’s outfit
3 shirts
6 pair of shorts
2 shirts
1 blouse
4 tops
2 pair of pants
3 shirts
2 pillowcases
2 dresses
2 blouses
6 handkerchiefs
Starting Your Dryer
WARNING
WARNING
Explosion Hazard
Fire Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Do not dry anything that has ever had anything
flammable on it (even after washing).
Items containing foam, rubber, or plastic must be dried
on a clothesline or by using an Air Cycle.
Failure to follow these instructions can result in death,
explosion, or fire.
Failure to follow these instructions can result in death
or fire.
This booklet covers several different models. Your dryer may not
have all of the cycles and features described.
Before using your dryer, wipe the dryer drum with a damp cloth to
remove dust from storing and shipping.
Stopping and Restarting
You can stop your dryer anytime during a cycle.
To stop your dryer
Open the dryer door or turn the Cycle Control knob to OFF.
NOTE: The Cycle Control knob should point to an Off area when
the dryer is not in use.
To restart your dryer
Close the door. Select a new cycle and temperature (if desired).
Press the PUSH TO START button.
1. Load clothes loosely into the dryer and close the door. Do not
pack the dryer. Allow space for clothes to tumble freely.
2. Turn the Cycle Control knob to the recommended cycle for the
type of load being dried. Use the Energy Preferred Automatic
Setting to dry most heavy to medium weight fabrics.
3. (OPTIONAL) Your dryer may have an END OF CYCLE SIGNAL.
The signal is helpful when drying items that should be
removed from the dryer as soon as it stops. The End of Cycle
signal is part of the Start button and is selectable. Turn the
Start button to ON or OFF. The signal will sound only if the
selector is set to On.
4. If desired, add fabric softener sheet. Use only ones labeled as
dryer safe. Follow package instructions.
5. Press the PUSH TO START button.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHER/DRYER CARE
Cleaning Your Washer
Cleaning the Lint Screen
Use a soft, damp cloth or sponge to wipe up any spills such as
detergent or bleach from the outside of your washer.
Clean the lint screen before each load. A screen blocked by lint
can increase drying time.
Clean your washer interior by mixing 1 cup (250 mL) of chlorine
bleach and 2 cups (500 mL) of detergent. Pour this mixture into
your washer and run it through a complete cycle using hot water.
Repeat this process if necessary.
Remove any hard water deposits using only cleaners labeled as
washer safe.
IMPORTANT:
ꢀ
Do not run the dryer with the lint screen loose, damaged,
blocked, or missing. Doing so can cause overheating and
damage to both the dryer and fabrics.
ꢀ
If lint falls off the screen into the dryer during removal, check
the exhaust hood and remove the lint.
Cleaning the liquid fabric softener dispenser (on some
models):
Every Load Cleaning
1. Remove dispenser by grasping top with both hands and
squeezing, while pushing upward with thumbs.
Style 1:
2. Rinse dispenser under a warm water faucet, then replace it.
1. The lint screen is located inside the dryer on the back wall.
NOTE: If your model has a liquid fabric softener dispenser, do not
wash clothes with this dispenser removed. Do not add detergent
or bleach to this dispenser; it is for liquid fabric softener only.
Pull out the lint screen and its cover.
2. Separate the cover and the screen by squeezing the screen
and pulling on the cover at the same time.
3. Roll lint off the screen with your fingers. Do not rinse or wash
screen to remove lint. Wet lint is hard to remove.
Water Inlet Hoses
4. Put the lint screen and cover back together and push firmly
back into place.
Style 2:
Replace inlet hoses after 5 years of use to reduce the risk of hose
failure. Periodically inspect and replace inlet hoses if bulges,
kinks, cuts, wear or leaks are found.
1. The lint screen is located inside the dryer in the front door well.
Pull the lint screen straight up. Roll lint off the screen with your
fingers. Do not rinse or wash screen to remove lint. Wet lint is
hard to remove.
When replacing your inlet hoses, mark the date of replacement on
the label with a permanent marker.
Cleaning the Washer/Dryer
Location
2. Push the lint screen firmly back into place.
As Needed Cleaning
Keep washer/dryer area clear and free from items that would
obstruct the flow of combustion and ventilation air.
1. Roll lint off the screen with your fingers.
2. Wet both sides of lint screen with hot water.
3. Wet a nylon brush with hot water and liquid detergent. Scrub
WARNING
lint screen with the brush to remove residue buildup.
4. Rinse screen with hot water.
5. Thoroughly dry lint screen with a clean towel. Replace screen
in dryer.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Failure to do so can result in death, explosion, or fire.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Non-use or vacation care
Cleaning the Dryer Interior
Operate your washer/dryer only when you are at home. If you will
be on vacation or not using your washer/dryer for an extended
period of time, you should:
1. Apply a nonflammable household cleaner to the stained area
of the drum and rub with a soft cloth until stain is removed.
2. Wipe drum thoroughly with a damp cloth.
3. Tumble a load of clean cloths or towels to dry the drum.
NOTE: Garments which contain unstable dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the dryer
interior. These stains are not harmful to your dryer and will not
stain future loads of clothes. Dry unstable dye items inside-out to
prevent dye transfer.
ꢀ
Unplug washer/dryer or disconnect power.
ꢀ
Turn off the water supply to the washer. This helps avoid
accidental flooding (due to a water pressure surge) while you
are away.
To transport the washer/dryer
1. Shut off both water faucets. Disconnect and drain water inlet
Removing Accumulated Lint
From Inside the Dryer Cabinet
hoses. Place the inlet hoses into the basket.
2. If washer/dryer will be moved during freezing weather, put in
1 qt (1 L) of R.V.-type antifreeze in the basket. Run washer on
a spin setting for about 30 seconds to mix the antifreeze and
water.
3. Disconnect the drain from the drain system.
4. Unplug washer/dryer or disconnect power.
5. Disconnect the exhaust vent.
Lint should be removed every 2 years, or more often, depending
on dryer usage. Cleaning should be done by a qualified person.
From Inside the Exhaust Vent
Lint should be removed every 2 years, or more often, depending
on dryer usage.
6. If your washer/dryer is a gas model, close shutoff valve in gas
supply line, disconnect gas supply line pipe and remove
fittings attached to the washer/dryer pipe.
7. Wash lint screen.
Moving & Storage
8. Drape the power cord and drain hose over edge and in the
Install and store your washer/dryer where it will not freeze.
Because some water may stay in the hoses, freezing can damage
your washer/dryer. If storing or moving your washer/dryer during
freezing weather, winterize it.
basket.
9. Make sure leveling legs are secure. Use masking tape to
secure the washer lid and dryer door.
Reinstalling your washer/dryer
To winterize washer/dryer
1. Follow the “Installation Instructions” to locate, level, and
1. Shut off both water faucets. Disconnect and drain water inlet
connect the washer/dryer.
hoses. Put 1 qt (1 L) of R.V.-type antifreeze in the basket.
2. Run the washer through the Normal cycle with 1 scoop or cap
full of detergent to clean the washer and remove the
antifreeze, if used.
2. Run washer on a drain and spin setting for about 30 seconds
to mix the antifreeze and water.
3. Unplug washer/dryer or disconnect power.
To use washer/dryer again
1. Flush water pipes and hoses. Reconnect water inlet hoses.
Turn on both water faucets.
2. Plug in washer/dryer or reconnect power.
3. Run the washer through a complete cycle with 1 cup (250 mL)
of detergent to clean out antifreeze.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHER TROUBLESHOOTING
First try the solutions suggested here and possibly avoid the cost of a service call...
Washer and Components
Washer Operation
Noisy
Washer stops, won’t fill, rinse or agitate
ꢀ
Is the load balanced and the washer/dryer level? The wash
ꢀ
Check the following:
load should be balanced and not overloaded. The washer/
dryer must be level. The front feet should be properly installed
and the nuts tightened. Reset the rear leveling legs (if needed).
See the Installation Instructions.
Is the power cord plugged into a grounded 3 prong outlet?
Is the indicator on the Cycle Control knob properly lined up
with a cycle? Turn the Cycle Control knob to the right slightly
and pull to start.
ꢀ
ꢀ
Did you completely remove the yellow shipping strap with
cotter pins? See the Installation Instructions.
Are the water inlet valve screens clogged?
Are both the hot and cold water faucets turned on?
Is the water inlet hose kinked?
Are the gears engaging after the drain and before spin, or
is the upper part of agitator clicking during wash? These
are normal washer noises.
ꢀ
Does the water level seem too low, or does the washer
appear to not fill completely? The top of the agitator is much
higher than the highest water level. This is normal and
necessary for clothes to move freely.
Leaking
ꢀ
Check the following:
ꢀ
ꢀ
ꢀ
ꢀ
Is there power at the plug? Check your electrical source or
Are the fill hoses tight?
call an electrician.
Are the fill hose washers properly seated?
Has a fuse blown or is the circuit breaker open? If problem
continues, call an electrician.
Is the drain hose clamp properly installed? See the Installation
Instructions.
Are you using an extension cord? Do not use an extension
cord.
ꢀ
ꢀ
Is the sink or drain clogged? Sink and standpipe must be
able to handle 17 gal. (64 L) of water per minute.
Is the washer in a normal pause in the cycle? The washer
pauses for about 2 minutes during certain cycles. Allow the
cycle to continue. Some cycles feature periods of agitation
and soak.
Is water deflecting off the tub ring or the load? Center the
tub before starting the washer. The wash load should be
balanced and not overloaded. The fill or spray rinses can
deflect off the load. The washer/dryer must be level. Ensure
that the leveling legs are properly installed. See the Installation
Instructions.
ꢀ
ꢀ
Is the washer overloaded? Wash smaller loads.
Is the lid open? The lid must be closed during operation.
Washer will not agitate or spin with the lid open.
ꢀ
Check household plumbing for leaks.
Washer won’t drain or spin
Basket crooked
ꢀ
Is the drain hose clogged, or the end of the drain hose
more than 96 in. (244 cm) above the floor? See the
Installation Instructions for proper installation of drain hose.
ꢀ
ꢀ
Was the washer basket pulled forward during loading?
Push the basket to the center before starting wash.
Is the load balanced and the washer/dryer level? The wash
load should be balanced and not overloaded. The washer/
dryer must be level. Ensure that the leveling legs are properly
installed. See the Installation Instructions.
ꢀ
ꢀ
Is the lid open? The lid must be closed during operation.
Washer will not agitate or spin with the lid open.
Is there excessive sudsing? Always measure detergent.
Follow manufacturer’s directions. If you have very soft water,
you may need to use less detergent.
ꢀ
ꢀ
The washer basket moves while washing. This is normal.
ꢀ
Is your voltage low? Check your electrical source or call an
electrician. Do not use an extension cord.
Agitator operation
The top of the agitator is loose, or moves in only one
direction. This is normal.
Washer continues to fill or drain, cycle seems stuck
ꢀ
ꢀ
Is the top of drain hose lower than the water level in
washer? The top of the hose must be higher than the water
level in the washer for proper operation. See the Installation
Instructions.
Dispenser clogged (on some models)
ꢀ
Did you follow the manufacturer’s directions when adding
fabric softener to the dispenser (on some models)?
Measure fabric softener and carefully pour into the dispenser.
Wipe up all spills. Dilute fabric softener in the fabric softener
dispenser.
Does the drain hose fit too tightly in the standpipe, or is it
taped to the standpipe? The drain hose should be loose yet
fit securely. Do not seal the drain hose with tape. The hose
needs an air gap. See the Installation Instructions.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
Did you overload the washer? The wash load must be
balanced and not overloaded. Loads should move freely
during washing.
Wash temperature not what I selected
ꢀ
Are the hot and cold water inlet hoses reversed? See the
Installation Instructions for more information. As your
frequency of loads washed increases, the water temperature
may decrease for hot and warm temperature selections. This
is normal.
To reduce wrinkling of permanent press clothes and some
synthetic knits, use a large load size to provide more space.
ꢀ
ꢀ
Was the wash water warm enough to relax wrinkles, or are
you using warm rinses? If safe for the load, use warm or hot
wash water. Use cold rinse water.
Are the hot and cold water hoses reversed? Check to be
sure the hot and cold water hoses are connected to the right
faucets. See the Installation Instructions.
Washer Results
Load too wet
Load is tangled or twisted
ꢀ
ꢀ
Did you use the right cycle for the load being washed?
Select a cycle with a higher spin speed (if available).
ꢀ
ꢀ
Did you overload the washer? The wash load must be
balanced and not overloaded. Loads should move freely
during washing.
Did you use a cold rinse? Cold rinses leave loads wetter than
warm rinses. This is normal.
Did you wrap items around the agitator? Drop items loosely
into the washer. Do not wrap items around the agitator.
Residue or lint on load
ꢀ
ꢀ
Did you sort properly? Sort lint givers (towels, chenille) from
Gray whites, dingy colors
lint takers (corduroy, synthetics). Also sort by color.
ꢀ
ꢀ
ꢀ
ꢀ
Did you properly sort the load? Dye transfer can occur when
mixing whites and colors in a load. Sort dark clothes from
whites and lights.
Did you overload the washer? The wash load must be
balanced and not overloaded. Clothes should move freely.
Lint can be trapped in the load if overloaded. Wash smaller
loads.
Was the wash temperature too low? Use hot or warm
washes if safe for the load. Make sure your hot water system
is adequate enough to provide a hot water wash.
ꢀ
Did you select the correct water level? The water level
should be correct for the load size. Clothes should move freely
in the water.
Did you use enough detergent, or do you have hard
water? Use more detergent for washing heavy soils in cold or
hard water.
ꢀ
ꢀ
ꢀ
Did you use enough detergent? Follow manufacturer’s
directions. Use enough detergent to hold the lint in the water.
Are the hot and cold water hoses reversed? Check to be
sure the hot and cold water hoses are connected to the right
faucets. See the Installation Instructions.
Did you line dry your clothing? If so, you can expect some
lint on the clothing.
Check the following:
Was paper or tissue left in the pockets?
Garments damaged
Check the following:
Is your water colder than 70°F (21°C)? Wash water colder than
70°F (21°C) may not completely dissolve the detergent.
ꢀ
Were sharp items removed from pockets before washing?
Empty pockets, zip zippers, snap or hook fasteners before
washing.
Did you use the proper cycle time for the load? Reducing
wash time (duration) is another way to reduce lint.
Were strings and sashes tied to prevent tangling?
Stains on load
Were items damaged before washing? Mend rips and broken
threads in seams before washing.
ꢀ
Did you follow the manufacturer’s directions when adding
detergent and fabric softener? Measure detergent and
fabric softener. Use enough detergent to remove soil and hold
it in suspension. Dilute fabric softener and add to the rinse
portion of a cycle only. Do not drip fabric softener on clothes.
ꢀ
ꢀ
ꢀ
Did you overload the washer? The wash load must be
balanced and not overloaded. Loads should move freely
during washing.
Did you add chlorine bleach properly? Do not pour chlorine
bleach directly onto load. Wipe up bleach spills. Undiluted
bleach will damage fabrics.
ꢀ
ꢀ
ꢀ
Is there above average iron (rust) in water? You may need
to install an iron filter.
Did you properly sort the load? Sort dark clothes from
whites and lights.
Did you follow the manufacturer’s care label instructions?
Did you unload the washer promptly? To avoid dye transfer,
unload the washer as soon as it stops.
Load is wrinkled
ꢀ
ꢀ
Did you unload the washer promptly? Unload the washer as
soon as it stops.
Did you use the right cycle for the load being washed?
Use the cycle for Casual or Permanent Press clothes or
another cycle with low spin speeds (if available) to reduce
wrinkling.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DRYER TROUBLESHOOTING
First try the solutions suggested here and possibly avoid the cost of a service call...
Lint on load
Dryer Operation
Dryer will not run
ꢀ
ꢀ
ꢀ
ꢀ
Is the lint screen clogged? Clean lint screen. Check for air
movement.
Is the load properly sorted? Sort lint givers (towels, chenille)
from lint takers (corduroy, synthetics). Also sort by color.
ꢀ
Check the following:
Is the power cord plugged in?
Is the load too big or too heavy? Dry smaller loads so lint
can be carried to the lint screen.
Has a fuse blown, or has a circuit breaker tripped? There
may be 2 fuses or circuit breakers for the dryer. Check to
make sure both fuses are intact and tight, or that both circuit
breakers have not tripped.
Was the load overdried? Use correct dryer settings for load
type. Overdrying can cause lint-attracting static electricity.
See “Dryer Cycle Descriptions” (separate sheet).
Was a regular fuse used? Use a time-delay fuse.
Is the dryer door firmly closed?
Was the Start button firmly pressed?
Is a cycle selected?
ꢀ
ꢀ
Was paper or tissue left in pockets?
Is pilling being mistaken for lint? Pilling (surface fuzz) is
caused by normal wear and laundering.
Stains on load or color change
No heat
ꢀ
Was dryer fabric softener properly used? Add dryer fabric
softener sheets at the beginning of the cycle. Fabric softener
sheets added to a partially-dried load can stain your
garments.
ꢀ
Has a fuse blown, or a circuit breaker tripped? Electric
dryers use 2 household fuses or breakers. The drum may be
turning, but you may not have heat.
ꢀ
ꢀ
Were items soiled when placed in the dryer? Items should
ꢀ
ꢀ
Has an air dry cycle been selected? Select the right cycle
be clean before being dried.
for the types of garments being dried.
Were items properly sorted? Sort light colors from dark
colors. Sort colorfast items from noncolorfast items.
For gas dryers, is the valve open on the supply line?
Unusual sounds
Items shrinking
ꢀ
ꢀ
Has the dryer had a period of non-use? If the dryer hasn’t
been used for a while, there may be a thumping sound during
the first few minutes of operation.
ꢀ
ꢀ
Was the dryer overloaded? Dry smaller loads that will tumble
freely.
Did the load overdry? Check the manufacturer’s care label.
Match dryer setting to load type.
Is it a gas dryer? The gas valve clicking is a normal operating
sound.
Loads are wrinkled
Dryer Results
Clothes are not drying satisfactorily
ꢀ
ꢀ
Was the load removed from dryer at the end of the cycle?
Was the dryer overloaded? Dry smaller loads that can
tumble freely.
ꢀ
Check the following:
Is the lint screen clogged with lint?
ꢀ
Did the load overdry? Check the manufacturer’s care label.
Match dryer setting to load type.
Is the exhaust vent or outside exhaust hood clogged with lint,
restricting air movement? Run the dryer for 5-10 minutes.
Hold your hand under the outside exhaust hood to check air
movement. If you do not feel air movement, clean exhaust
system of lint or replace exhaust vent with heavy metal or
flexible metal vent. See your Installation Instructions.
Odors
ꢀ
ꢀ
Have you recently been painting, staining or varnishing in
the area where your washer/dryer is located? If so,
ventilate the area. When the odors or fumes are gone from the
area, rewash and dry the clothing.
Is the exhaust vent crushed or kinked? Replace with heavy
metal or flexible metal vent. See your Installation Instructions.
If the dryer is electric, is it being used for the first time?
The new electric heating element may have an odor. The odor
will be gone after the first cycle.
Are fabric softener sheets blocking the grille? Use only one
fabric softener sheet, and use it only once.
ꢀ
ꢀ
ꢀ
Is the washer/dryer located in a room with temperature
below 45ºF (7ºC)? Proper operation of dryer cycles requires
temperatures above 45ºF (7ºC).
Garment damage
ꢀ
Check the following:
Were zippers, snaps, and hooks left open?
Was a cold rinse water used? Was the load very wet?
Expect longer drying times with items rinsed in cold water and
with items that hold moisture (cottons).
Were strings and sashes tied to prevent tangling?
Were care label instructions followed?
Were items damaged before drying?
Is the load too large and heavy to dry quickly? Separate the
load to tumble freely.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
11
Download from Www.Somanuals.com. All Manuals Search And Download.
®
CROSLEY WASHER/DRYER WARRANTY
ONE-YEAR FULL WARRANTY
For one year from the date of purchase, when this washer/dryer is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Corporation will pay for factory specified parts and repair labor costs to correct defects in
materials or workmanship. Service must be provided by a Whirlpool designated service company.
SECOND THROUGH FIFTH-YEAR LIMITED WARRANTY - ON TOP, LID AND GEARCASE ASSEMBLY
In the second through fifth years from the date of purchase, when this washer/dryer is operated and maintained according to
instructions attached to or furnished with the product, Whirlpool Corporation will pay for factory specified parts for the following
components, if defective in materials or workmanship: top and lid (if rusted); any part of the gearcase assembly.
SECOND THROUGH TENTH-YEAR LIMITED WARRANTY - ON OUTER TUB
In the second through tenth years from the date of purchase, when this washer/dryer is operated and maintained according to
instructions attached to or furnished with the product, Whirlpool Corporation will pay for factory specified parts for the outer tub should
it crack or fail to contain water, or if found to be defective in materials or workmanship.
Whirlpool Corporation will not pay for:
1. Service calls to correct the installation of your washer/dryer, to instruct you how to use your washer/dryer, or to replace house fuses,
reset circuit breakers, correct house wiring, plumbing or venting or to replace owner accessible light bulbs. Heavy 4 in. (10.2 cm)
metal exhaust vent must be used. Refer to the venting section of this manual and your Installation Instructions.
2. Repairs when your washer/dryer is used in other than normal, single-family household use.
3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation (including, but not limited
to, venting with plastic or flexible foil), installation not in accordance with local electrical and plumbing codes, or use of products not
approved by Whirlpool Corporation.
4. Any labor costs incurred during the limited warranty periods.
5. Replacement parts or repair labor costs for units operated outside the United States.
6. Pickup and delivery. This product is designed to be repaired in the home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation may not
apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Outside the 50 United States, this warranty does not apply. Contact your authorized Crosley dealer to determine if another
warrany applies.
7/03
Replacement parts
To locate factory specified replacement parts in your area:
If you need to order replacement parts, we recommend that you
only use factory specified parts. These parts will fit right and work
right because they are made with the same precision used to
build every new CROSLEY® appliance.
Call the Customer Interaction Center at 1-800-253-1301, or your
nearest designated service center.
For information on how to contact Whirlpool Corporation, please
see front page of this document.
8546451
9/03
Printed in U.S.A.
© 2003. All rights reserved.
® Registered Trademark of The Crosley Group, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|