Model No. WLTL29320
Serial No.
USER'S MANUAL
Serial Number
Decal
QUESTIONS?
If you have questions, or if there
are missing parts, we will guar-
antee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
Customer Hot Line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See BE-
FORE YOU BEGIN on page 4 if the treadmill
is not working properly.)
kg) to raise, lower, or move the treadmill.
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
20. Inspect and properly tighten all parts of the
treadmill regularly.
15. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
21. Never insert any object into any opening.
22.
DANGER:
Always unplug the power
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized ser-
vice representative only.
17. Never leave the treadmill unattended while it
is running. Always remove the key and un-
plug the power cord when the treadmill is not
in use.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO FOLD
AND MOVE THE TREADMILL on page 11.)
You must be able to safely lift 45 pounds (20
23. This treadmill is intended for in-home use
only. Do not use this treadmill in a commer-
cial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. WESLO assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown have been placed on your
treadmill. If a decal is missing, or if it is not
legible, please call our Customer Service
Department, toll-free, to order a free replace-
ment decal (see ORDERING REPLACEMENT
PARTS on the back cover of this manual).
Apply the decal in the location shown. Note:
The decals are not shown at actual size.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Congratulations for selecting the new WESLO® CA-
DENCE C42 treadmill. The CADENCE C42 treadmill
combines advanced technology with innovative design
to help you get the most from your exercise in the con-
venience and privacy of your home. And when you’re
not exercising, the unique CADENCE C42 can be
folded up, requiring less than half the floor space of
other treadmills.
at 1-800-999-3756, Monday through Friday, 6 a.m. until
6 p.m. Mountain Time (excluding holidays). To help us
assist you, please note the product model number and
serial number before calling. The model number of the
treadmill is WLTL29320. The serial number can be
found on a decal attached to the treadmill (see the
front cover of this manual for the location).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are la-
beled.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our Customer Service Department toll-free
Bookrack
Console
Water Bottle Holder
(Bottle not included)
Key/Clip
Upright
Handrail
Storage Latch
RIGHT SIDE
Walking Belt
Foot Rail
Circuit Breaker
Power Cord
Cushioned Walking Platform
for maximum exercise comfort
BACK
Incline Leg
Rear Roller
Adjustment Bolts
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included small allen wrench
and your own phillips screwdriver
,
rubber mallet
pliers
, wire cutters
, adjustable wrenches , and needlenose
.
To identify small parts during assembly, use the PART IDENTIFICATION CHART in the center of this manual.
1. Make sure that the power cord is unplugged.
1
40
87
75
40
102
With the help of a second person, carefully tip the
treadmill onto one side. Partially fold the Frame (75) so
that the treadmill is more stable. Do not fully fold the
treadmill until it is completely assembled.
87
Attach four Base Pads (40) to the Base (11) with two
1 1/4” Tek Screws (87) and two 3/4” Tek Screws (102) in
the locations shown.
40
11
102
2. With the help of a second person, tip the treadmill down
2
to the position shown.
76
Attach a Wheel (37) to each side of the Base (11) with a
Wheel Bolt (36) and a Wheel Nut (38) as shown.
62
Holes
Identify the Right Upright (62) and the Left Upright (76)
(there are two small holes in the side of the Left Upright).
Remove any plastic ties that are in the square holes in
the Uprights. While a second person holds the Right
Upright near the Wire Harness (21), insert the end of the
Wire Harness into the lower end of the Right Upright and
out of the upper end.
21
11
37
38
36
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Insert a Plastic Shim (97) into each side of the post on
the right side of the Base (11). Next, orient the Right
Upright (62) as shown, and insert it into the Base. Make
sure that the Wire Harness (21) does not fall into the
Right Upright. Be careful to avoid pinching the Wire
Harness. Note: If necessary, tap the Right Upright with a
rubber mallet until it is fully seated in the Base. If the
Right Upright cannot be fully seated, remove the outer
Plastic Shim and then insert the Right Upright.
3
21
62
This hole
must be
on this side.
Attach the Right Upright (62) to the Base (11) with three
1” Bolts (8) and three Star Washers (9). Do not tighten
the Bolts yet.
Assemble the Left Upright (not shown) in the same way.
9
8
97
9
8
11
4. Hold the Crossbar (34) between the Uprights (62, 76).
Attach the Crossbar with two 2 1/2” Bolts (53) and two
5/16” Washers (57). Do not tighten the Bolts yet.
4
53
34
57
57
53
76
62
5. Identify the Right Handrail (47), which has a large hole in
the left side. Feed the Wire Harness (21) up into the rec-
tangular bracket on the Right Handrail and out the large
hole in the left side. Note: It may be helpful to use
needlenose pliers to pull the Wire Harness out of the
large hole.
5
Ground
Wire
8
21
1
96
Remove any plastic ties that are in the rectangular
bracket on the Right Handrail (47). Insert the bracket into
the top of the Right Upright (62). Attach the upper and
lower ends of the Right Handrail to the Right Upright with
two 1” Bolts (8). Do not tighten the Bolts yet.
Large
Hole
8
47
76
Bracket
Attach the Left Handrail (1) as described above. Note:
There is not a wire harness on the left side.
62
Attach the end of the ground wire to the small hole in the
side of the Right Handrail (47) with a Silver Ground
Screw (96).
8
8
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Place the Console Base (46) on the Right Handrail (47)
and the Left Handrail (not shown). Touch the Right
Upright (62) to discharge any static.
6
10
Hold the Console (10) near the Console Base (46). Insert
the Wire Harness (21) through the two indicated plastic
ties on the Console Base. Next, insert the Wire Harness
up through the indicated opening in the Console Base
and through the plastic tie on the bottom of the Console.
Tie
21
46
Plug the widest connector on the Wire Harness (21) into
the widest connector on the Console (10). If the connec-
tor does not fit easily, rotate it and then connect it.
Plug the other connector on the Wire Harness into the
other connector on the Console. Note: The locations of
the connectors are shown by arrows.
47
Ties
21
Securely tighten the plastic tie on the Console (10) to
prevent the Wire Harness (21) from slipping. Then, cut
off the end of the plastic tie.
62
7. Set the Console (10) in the Console Base (46). Be careful
to avoid pinching any wires. Insert the excess Wire
Harness (21) into the large hole in the side of the Right
Handrail (47). Securely tighten the plastic ties on the
bottom of the Console Base to prevent the Wire
Harness from slipping. Cut off the ends of the plastic ties.
10
7
46
1
Ties
Attach the Console (10) to the Console Base (46) with
seven 3/4” Screws (13). Make sure that no wires are
pinched. Start all seven Screws before tightening
them; do not overtighten the Screws.
13
21
13
47
13
8
Attach the Console Base (46) to the Left and Right
Handrails (1, 47) with four 3/4” Screws (13).
8. Attach the Storage Latch (14) to the left Upright (76) with
two 3/4” Screws (13). Be careful not to overtighten the
Screws.
1
Lift the treadmill frame (see HOW TO FOLD THE
TREADMILL FOR STORAGE on page 11), but do not
latch it. Make sure that the frame is centered between
the Handrails (1, 47 [not shown]). Firmly tighten all of
the bolts and screws used in assembly steps 3, 4,
and 5. Then, lower the frame to the floor.
76
14
13
9. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included allen wrenches in a secure place. The large allen wrench is used to adjust the
walking belt (see page 13). To protect the floor or carpet, place a mat under the treadmill.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local WESLO dealer or call toll-free 1-800-806-
3651 and order part number 146148.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indi-
cate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Displays
Heart Rate
Sensor
Note: If there is a thin sheet of
plastic on the console, remove it.
Insert the key fully into the console. After a moment,
the displays will light. Test the clip by carefully tak-
ing a few steps backward until the key is pulled
from the console. If the key is not pulled from the
console, adjust the position of the clip.
CAUTION:
Before operating the
console, read the following precautions.
• Do not stand on the walking belt when turn-
ing on the power.
Follow the steps below to operate the console.
• Always wear the clip (see the drawing
below) while operating the treadmill.
Insert the key fully into the console.
1
• Adjust the speed in small increments to
avoid sudden jumps in speed.
A few seconds after the key is inserted, the dis-
plays will light.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed
water bottle in the water bottle holder.
Press the Speed LLbutton to start the walking
belt.
2
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
STEP-BY-STEP CONSOLE OPERATION
As you exercise, change the speed of the walking
belt as desired by pressing the Speed buttons.
Each time a button is pressed, the speed setting
will change by 0.1 mph; if a button is held down,
the speed setting will change in increments of 0.5
mph. Note: The console can display speed and
distance in either miles or kilometers (see
SPEED DISPLAY on page 10). For simplicity, all
instructions in this section refer to miles.
Before operating the console, make sure that the
power cord is properly plugged in (see page 8).
Next, stand on the foot
rails of the treadmill.
Find the clip attached to
Clip
the key, and slide the
clip onto the waistband
of your clothes.
Key
9
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop the walking belt, press the Stop button.
The Time/Distance display will begin to flash.
“E” for English miles or an “M” for metric kilometers
will appear in the Fat Calories/Calories/Pulse dis-
play. Press the Speed LLbutton to change the unit
of measurement. When the desired unit of mea-
surement is selected, remove the key and then
reinsert it.
Note: During the first few minutes that the treadmill
is used, inspect the alignment of the walking belt,
and align it if necessary (see page 13).
Change the incline of the treadmill as desired.
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
3
4
To change the incline of the treadmill, press either
of the Incline buttons until the desired incline level
is reached.
Measure your heart rate, if desired.
5
To measure your
heart rate, stand on
the foot rails and
place your thumb
on the heart rate
sensor. Do not
press too hard, or
the circulation in
your thumb will be restricted and your pulse
will not be detected. After a few seconds, the
heart-shaped indicator in the Fat Calories/Calories/
Pulse display will begin to flash, one or two dashes
(– –) will appear, and then your heart rate will be
shown. Hold your thumb on the heart rate sensor
for about 15 seconds for the most accurate read-
ing.
Follow your progress with the three displays.
Time/Distance
Mode Indicator
display—This display
shows the elapsed time
and the distance that
you have walked or run.
The display will change
from one number to the
other every few seconds, as shown by the mode
indicators. When the Stop button is pressed, the
display will flash.
Fat Calories/Calories/
Pulse display—This
display shows the ap-
proximate numbers of
fat calories and calories
you have burned (see
FAT BURNING on page 14). The display will
change from one number to the other every few
seconds, as shown by the mode indicators. The
display will also show your heart rate when you
use the heart rate sensor (see step 5).
If the displayed heart rate appears to be too high
or too low, or if your heart rate is not displayed, lift
your thumb off the heart rate sensor for a few sec-
onds. Then, place your thumb on the heart rate
sensor as described above. Remember to stand
still while measuring your heart rate.
When you are finished exercising, remove the
key.
6
Speed display—This
display shows the speed
of the walking belt
Step onto the foot rails, press the Stop button, and
remove the key from the console. Keep the key in a
secure place.
Note: The console can
display speed and dis-
tance in either miles or
kilometers. To change
the unit of measure-
ment, hold down the
WARNING:
Removing the key
does not cut off power to the incline sys-
tem. To prevent movement of the treadmill
and possible injury, unplug the power cord
when the treadmill is not in use.
Stop button, insert the key into the console, and
continue to hold the Stop button for a moment. An
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
1
Before folding the treadmill, unplug the power cord. CAUTION:
You must be able to safely lift 45 pounds (20 kg) in order to
raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown at
the right. To decrease the possibility of injury, bend your
legs and keep your back straight. As you raise the tread-
mill, make sure to lift with your legs rather than your
back. Raise the treadmill about halfway to the vertical posi-
tion.
2. Move your right hand to the position shown and hold the
2
treadmill firmly. Press out on the storage latch. Raise the
treadmill until the storage latch closes over the catch. Make
sure that the storage latch is fully engaged over the
catch.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage
position in temperatures above 85° Fahrenheit.
Engaged
Storage
Latch
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the storage latch
is fully engaged over the catch.
1. Hold the upper ends of the handrails. Place one foot on the
base as shown.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. To re-
duce the risk of injury, use extreme caution while mov-
ing the treadmill. Do not move the treadmill over an un-
even surface.
Base
3. Place one foot on the base, and carefully lower the treadmill
until it is resting in the storage position.
Front Wheels
HOW TO LOWER THE TREADMILL FOR USE
1. See drawing 2 above. Hold the upper end of the treadmill with your right hand as shown. Press the storage
latch and hold it. Pivot the treadmill until the frame and foot rail are past the storage latch.
2. See drawing 1 above. Hold the treadmill firmly with both hands, and lower the treadmill to the floor. Do not
drop the treadmill frame to the floor. To decrease the possibility of injury, bend your legs and keep
your back straight.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-
free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 8. Important: The treadmill is not compatible
with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
c
frame near the power cord. If the switch protrudes
as shown, the circuit breaker has tripped. To reset
the circuit breaker, wait for five minutes and then
press the switch back in.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the screws from
the hood, and carefully remove the hood.
Locate the Reed Switch (44) and the Magnet (45) on
the left side of the Pulley (50). Turn the Pulley until the
a
1/8”
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8”. If necessary, loosen the Reed
Switch Screw (103) and move the Reed Switch
slightly. Retighten the Screw. Re-attach the hood, and
run the treadmill for a few minutes to check for a cor-
rect speed reading. Reattach the Resistance Knob.
50
44
103
45
Top
View
12
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 2 to
3 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, in-
sert the key and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
2”–3”
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, please call our toll-free Customer Service
Department.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
a
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the allen wrench to
turn the left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right, turn the
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove
b
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise,
1/4 of a turn. When the walking belt is correctly tight-
ened, you should be able to lift each side of the walk-
ing belt 2 to 3 inches off the walking platform. Be
careful to keep the walking belt centered. Plug in the
power cord, insert the key and carefully walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-
exercise problems.
To measure your heart rate during exercise, use the
pulse sensor. If your heart rate is too high or too low,
adjust the speed and incline of the treadmill.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
1
The correct form for several basic stretches is shown at the right.
Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees, and
back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back,
and groin.
3
3. Calf/Achilles Stretch
4
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles ten-
dons, bend your back leg as well. Stretches: Calves, achilles ten-
dons, and ankles.
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your but-
tocks as possible. Hold for 15 counts, then relax. Repeat 3 times for
both legs. Stretches: Quadriceps and hip muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give
the following information:
• The MODEL NUMBER of the product (WLTL29320)
• The NAME of the product (WESLO® CADENCE C42 treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED DRAW-
ING in the center of this manual)
WESLO is a registered trademark of ICON Health & Fitness, Inc.
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-
ited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, mis-
use, improper or abnormal usage or repairs not provided by an ICON authorized service center; prod-
ucts used for commercial or rental purposes; or products used as store display models. No other war-
ranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-
cidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 186970 R0902A
Printed in USA © 2002 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
Remove this chart and use it to identify small parts during assembly. Save
this chart and the EXPLODED DRAWING/PART LIST for future reference.
Silver Ground
Screw (96)–1
3/4” Screw (13)–13
3/4” Tek Screw
(102)–2
1 1/4” Tek Screw (87)–2
1” Bolt (8)–10
5/16” Washer (57)–2
Star Washer (9)–6
(May be an internal Star Washer)
2 1/2” Bolt (53)–2
Wheel Bolt (36)–2
Wheel Nut (38)–2
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. WLTL29320
R0902A
Key
No.
Key
No.
Qty.
Description
Qty.
Description
1
2
3
4
5
6
7
8
1
1
2
1
1
1
1
10
1
1
1
1
15
1
1
7
3
1
1
1
1
4
1
1
23
1
1
1
1
1
2
1
2
1
8
2
2
4
5
4
2
1
1
1
1
1
1
4
2
1
1
2
2
1
1
1
Left Handrail
Key/Clip
Incline Leg Pivot Bolt
Cover
Left Foot Rail
Lift Motor
Rear Roller
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
#
4
2
1
1
2
1
3
1
2
2
1
1
1
12
1
1
2
1
1
1
2
1
4
1
2
1
2
1
1
1
2
1
1
1
4
1
1
1
2
1
4
1
1
1
1
2
1
1
1
1
1
1
1
5/16” Washer
Frame Pivot Bolt
Latch Decal
Motor Belly Pan
Cable Tie Clamp
Right Upright
Releasable Tie
Choke
Belt Guide
Belly Pan Fastener
Walking Belt
Walking Platform
Belly Pan
Electronics Screw
Incline Wire Harness
Upright Grommet
Small Screw
5/32” Allen Wrench
Frame
Left Upright
Incline Wheel Bolt
Power Supply Plate
Incline Wheel Nut
Ground Wire
Hood Screw (Front)
Incline Leg
Rear Roller Adj. Bolt
Left Rear Endcap
Right Rear Endcap
Incline Motor Bolt
1 1/4” Tek Screw
Power Supply
Motor Belt Shield
Bookrack
Plastic Stand-off
Warning Decal
Right Foot Rail
Silver Screw
1” Bolt
9
Star Washer
Console Insert
Base
Motor Belt
3/4” Screw
Storage Latch
Thin Frame Spacer
8” Cable Tie
Motor Nut
Pulley/Flywheel/Fan
Motor
Motor/Pulley/Flywheel/Fan
Wire Harness
Belt Guide Screw
Motor Hood
Hood Shield
Screw
10
11
12
13
14
15
16
17
18
19
20*
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
Controller
Motor Swivel Bolt
Motor Tension Nut
Motor Star Washer
Motor Tension Washer
Motor Tension Bolt
Incline Stop Bracket
Insert Nut
Crossbar
Cage Nut
Wheel Bolt
Wheel
Wheel Nut/Lift Nut
Washer
Base Pad
Base Endcap
Latch Catch
Reed Switch Clip
Reed Switch
Magnet
Console Base
Right Handrail
Platform Screw
Isolator
Front Roller/Pulley
Front Roller Adj. Bolt
Incline Wheel
2 1/2” Bolt
Plastic Tie
Silver Ground Screw
Shim
Thin Frame Spacer
Hole Plug
Motor Controller Wire
Allen Wrench
3/4” Tek Screw
Reed Switch Screw
Incline Warning Decal
4” Blue Wire, 2F
8” Blue Wire, 2F
4” White Wire, M/F
8” White Wire, 2F
User’s Manual
#
#
#
#
Power Cord
Power Cord Grommet
Circuit Breaker
* Includes all parts shown in the box
# These parts are not illustrated
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. WLTL29320
R0902A
Download from Www.Somanuals.com. All Manuals Search And Download.
|