R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
EBV 210
FOR HOUSEHOLD USE ONLY
PARA USO CASERO SOLAMENTE
POUR UTILISATION À DES FINS
DOMESTIQUES SEULEMENT
DANGER:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Veuillez lire le manuel d’instructions et bien respecter tous les
avertissements et toutes les instructions de sécurité. Tout défaut
de le faire pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
Electrolux Canada Corporation
6150 McLaughlin Road
Mississauga, Ontario L5R 4C2
530088049
4/26/02
Copyright E2002 Electrolux Home Products, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
S Keep the extension cord clear of opera- come ineffective and result in serious in-
tor and obstacles at all times. Do not ex- jury.
pose cords to heat, oil, water, or sharp
edges.
S Avoid any body contact with any
grounded conductor, such as metal
fences, or pipes, to avoid the possibility
of electric shock. Don’t handle plug or
unit with wet hands.
S Do not use with damaged cord or plug. If
unit is not working as it should, has been
dropped, damaged, left outdoors, or
dropped into water, return it to your au-
thorized service dealer for repair.
S Ground Fault Circuit Interrupter (GFCI)
protection should be provided on the cir-
cuit or outlet to be used for this unit. Re-
ceptacles are available having built-in
GFCI protection and may be used for
this measure of safety.
UNIT/MAINTENANCE SAFETY
S Turn off all controls and allow the motor
to stop before disconnecting the unit
from the power source.
S Disconnect the unit from the power
source when not in use. Do not leave
the unit when it is plugged into outlet.
S Do not set the unit on any surface ex-
cept a clean, hard area while the unit is
running. Debris such as gravel, sand,
dust, grass, etc., could be picked up by
the air intake and thrown out through the
discharge opening, damaging the unit,
property, or causing serious injury to by-
standers or operator.
S Do not overreach or use from unstable
surfaces such as ladders, trees, steep
slopes, rooftops, etc. Use extra care
when cleaning on stairways. Keep firm
footing and balance at all times. Keep
hands out of tubes.
S Inspect the entire unit before each use
for worn, loose, missing, or damaged
parts. Do not use until the unit is in
proper working order.
S Disconnect unit from power source be-
fore servicing, cleaning, performing
maintenance, or storing.
S This unit is double insulated. See the
DOUBLE INSULATION CONSTRUCTION
section. Have all internal service per-
formed by qualified service repair per-
sonnel to avoid creating a hazard or
voiding your warranty.
S Have all maintenance other than the
recommended procedures described in
the instruction manual performed by
your authorized service dealer.
S Always see your authorized service
dealer to replace a damaged impeller.
Parts that are chipped, cracked, broken,
or damaged in any other way can fly
apart and cause serious injury. Replace
damaged parts before using the unit.
S Never place any object in the air intake
opening as this could restrict proper air
flow and cause damage to the unit.
S Never douse the unit with water or other
liquids or squirt with a water hose. Clean
with a damp sponge and mild soap.
See STORAGE.
S Check air intake openings and tubes
frequently, always with the unit stopped
and power source disconnected. Keep
vents and tubes free of debris which can
accumulate and restrict proper air flow.
S Do not burn, incinerate, or expose this
unit to extreme heat.
S Keep others including children, animals,
bystanders, and helpers a minimum of
30 feet (10 meters) away. Stop the mo-
tor immediately if you are approached.
Do not allow the unit to be used as a toy.
DOUBLE INSULATION
CONSTRUCTION
This unit is double insulated to help
protect against electric shock. Double
insulation construction consists of two
separate “layers” of electrical insula-
tion instead of grounding.
Tools and appliances built with a
double insulation system are not in-
tended to be grounded. No grounding
means is provided on this unit, nor
should a means of grounding be add-
ed to this unit. As a result, the exten-
sion cord used with your unit can be
plugged into any standard 120 volt
electrical outlet. Safety precautions
must be observed when operating any
electrical tool. The double insulation
system only provides added protection
against injury resulting from an internal
electrical insulation failure.
WARNING: All electrical repairs to
this unit, including housing, switch, mo-
tor, etc., must be diagnosed and re-
paired by qualified service personnel.
Replacement parts for a double insu-
lated appliance must be identical to the
parts they replace. A double insulated
appliance is marked with the words
“double insulation” or “double insu-
lated”. The symbol
(square within a
square) may also be marked on the ap-
pliance. Failure to have the unit repaired
by Sears service personnel can cause
the double insulation construction to be-
3
Download from Www.Somanuals.com. All Manuals Search And Download.
S Store the unit unplugged in a high, cool,
from the rotating blades.
dry, indoor area out of the reach of chil- S Hard objects can be thrown through the
dren.
collection bag or the housing and be-
come dangerous missiles which can
cause serious injury to the operator or
others.
S Use only recommended attachments
and replacement parts to avoid creating
a hazard and/or voiding warranty.
S Maintain the unit according to recom- S When using the vacuum attachment,
mended procedures.
the unit is designed to pick up dry mate-
rial such as leaves, grass, small twigs,
and bits of paper. Do not vacuum
stones, gravel, metal, broken glass, etc.,
to avoid severe damage to the impeller.
To avoid the possibility of electrical
shock, do not attempt to vacuum water
or other liquids.
S Never run the unit without the proper
equipment attached. When used as a
vacuum, always install vacuum tubes
and collection bag assembly. Make sure
the collection bag assembly is com-
pletely zipped when unit is running to
avoid flying debris. Use only recom-
mended attachments.
S Use only for jobs explained in the OP-
ERATION section of this manual.
BLOWER SAFETY
S Use only in daylight or in good artificial
light.
S Inspect the area before using the unit.
Remove all debris and hard objects
such as rocks, glass, wire, etc., that can
ricochet, be thrown, or otherwise cause
injury or damage during operation.
S Avoid accidental starting. Be sure the
switch is in the OFF position and keep
your hand and fingers away from the
switch while connecting the unit to the
power source or when carrying a unit
connected to the power source.
S Avoid situations which could set the col-
lection bag on fire. Do not vacuum dis-
carded matches, cigars, cigarettes, or
ash from fireplaces, barbecue pits,
brush piles, etc. To avoid spreading fire,
do not use blower near leaf or brush
fires, fireplaces, barbecue pits, ash-
trays, etc.
S Never run the unit without the proper
equipment attached. When used as a
blower, always install a blower tube. Use
only recommended attachments. Do
not use with any opening blocked, Keep
free of dust, lint, hair and anything that
may reduce air flow.
S To avoid spreading fire, do not use blow-
er near leaf or brush fires, fireplaces,
barbecue pits, ashtrays, etc.
S Always use the collection bag shoulder
strap when vacuuming to avoid loss of
control.
S Check air intake openings, elbow tube,
and vacuum tubes frequently, always
with the unit stopped and the power
source disconnected. Keep vents and
tubes free of debris which can accumu-
late and restrict proper air flow. Do not
use with any opening blocked, Keep
free of dust, lint, hair and anything that
may reduce air flow.
S Never place objects inside the blower
tubes; always direct the blowing debris
away from people, animals, glass, and
solid objects such as trees, automo-
biles, walls, etc. The force of air can
cause rocks, dirt, or sticks to be thrown
or to ricochet which can hurt people or
animals, break glass, or cause other
damage.
STANDARDS
S Never use for spreading chemicals, fer-
tilizers, or any other substances which
may contain toxic materials.
This product is listed by Underwriters Lab-
oratories, Inc., in accordance with UL
Standard 1017.
VACUUM SAFETY
If situations occur which are not covered
S Stop the motor and disconnect the pow- in this manual, use care and good judg-
er source before opening the air inlet ment. If you need assistance, contact
door or attempting to insert or remove your authorized service dealer or call
the vacuum tubes. The motor must be 1--800--235--5878. Failure to follow all
stopped and the impeller blades no Safety Rules and Precautions can result
longer turning to avoid serious injury in serious injury.
SAVE THESE INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
S Open the inlet cover by inserting the
WARNING: Stop the unit and
disconnect from the power source be-
fore opening the inlet cover or attempt-
ing to insert or remove the inlet restrictor,
blower tube, or vacuum tubes. The mo-
tor must be stopped and the impeller
blades no longer turning to avoid serious
injury from the rotating blades.
tip of a screwdriver into the latch area
on the blower unit. Gently tilt handle of
screwdriver toward the front of the unit
to release the latch while pulling up on
the vacuum inlet cover with your other
hand.
Bottom view
of unit
Latch Area
WARNING: If received as-
sembled, ensure your unit is properly
assembled and all fasteners are secure.
S A standard screwdriver is required for
assembly.
Vacuum Inlet Cover (closed)
Impeller
h Area
BLOWER ASSEMBLY
NOTE: Assembly instructions for using
your unit as a vacuum follow this section.
Attaching the blower tube
If you have already assembled your unit
for use as a vacuum, refer to the section
HOW TO CONVERT UNIT FROM VACUUM
USE TO BLOWER USE.
Vacuum Inlet Cover (opened)
S Turn the inlet restrictor counterclock-
wise and remove it from the unit. Do not
close the inlet door. You will next attach
the vacuum tubes.
To attach blower tube:
S Align the grooves on the blower tube
with the grooves on the blower outlet.
S Push the blower tube onto the blower
outlet until it snaps into place (tube is
secured by red tube release button).
S To remove the blower tube, press the
tube release button while pulling on
tube.
Vacuum
Inlet Cover
Inlet
Restrictor
Tube Release Button
Blower Tube
Attaching the vacuum tubes
There are 2 vacuum tubes, an upper
tube and a lower tube. The upper tube
has a vacuum assist handle attached to
one end and is cut straight on both ends.
The upper tube attaches to the blower
unit. The lower tube has an angled end
that you point toward the ground during
vacuum use. The lower tube attaches to
the upper tube.
Blower outlet
VACUUM ASSEMBLY
NOTE: Assembly instructions for using
your unit as ablower areexplained inthe
previous section.
If you have already assembled your unit
for use as a blower, remove the blower
tube.
S Ensure unit is stopped and extension
cord is unplugged.
S While holding inlet cover open, place
the hooks of the vacuum assist handle
on the retaining posts of the unit.
Remove the inlet restrictor
An inlet restrictor is used when using your
unit as a blower. This restrictor is not used
during vacuum use and must be removed
during assembly for vacuum use.
Upper Vacuum Tube
Vacuum Assist Handle
NOTE: Be sure to keep the inlet re-
strictor for using your unit as a blower.
S Ensure unit is stopped and extension
cord is unplugged.
Hook
5
Download from Www.Somanuals.com. All Manuals Search And Download.
S Pivot the tube until it is secured to the
blower unit by the red inlet cover latch.
Last In
First In
S Position the unit on your right-hand
side, blower outlet and bag pointing to-
ward the rear. Hold the unit in an up-
right position with the lower vacuum
tube on the ground to support it.
S Place the shoulder strap over your
head and onto your left shoulder.
S Adjust the strap to allow a free flow of
air from the blower. If the collection
bag is kinked, the unit will not operate
properly.
Retaining Post
S Attach the lower vacuum tube to the
upper vacuum tube by aligning the ar-
rows on the two tubes. Press the tubes
together until the lower tube is fully
seated in the upper tube. (About 3 in-
ches)
NOTE: The strap is designed to posi-
tion the collection bag on your shoulder
without kinks. The strap is not intended
to support the weight of the unit.
Upper Tube Lower Tube
Align arrows on upper
and lower tubes
Shoulder strap
on left shoulder
COLLECTION BAG ASSEMBLY
S Open the zipper on the collection bag
and insert the elbow tube.
S Push the small end of the elbow tube
through the small opening in the bag.
No kinks in bag
NOTE: Make sure edge of the small
opening is flush against the flared area
of the elbow tube and the hole for the
tube release button is on top.
allows free air flow
HOW TO CONVERT UNIT FROM
VACUUM USE TO BLOWER USE
S Stop unit and unplug the extension
cord.
S Remove the vacuum tubes by insert-
ing the tip of a screwdriver into the
latch area on the vacuum assist han-
dle. Gently tilt handle of screwdriver
toward the front of the unit to release
the latch while pulling up on the vacu-
um assist handle with your other hand.
Tube
Elbow Tube
Release
Button
Hole
Zipper
Opening
Small
Opening
S Close the zipper on the bag.
Make
sure the zipper is closed completely.
S Align the grooves on the elbow tube
with the grooves on the blower outlet.
S Push the elbow tube onto the blower
outlet until it snaps into place (elbow
tube is secured by red tube release
button).
Vacuum
Assist
Handle
ADJUSTING THE SHOULDERSTRAP
ON THE COLLECTION BAG
S Remove the collection bag.
S Carefully loop the shoulder strap S Install the inlet restrictor that was re-
through the buckle as shown in the il-
lustration below.
moved when assembling for vacuum
use.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: If you are unable to locate the
inlet restrictor, the unit will still operate.
This restrictor improves the blower
function.
D Heavy enough to carry full current from
the power source to the unit. Otherwise,
loss of power and overheating can oc-
cur causing damage to unit. Refer to
table for minimum wire gauge recom-
mendations. The cord must be marked
with the proper wire gauge. (Appropriate
extension cords are available.) Do not
use multiple cords.
D In good condition. Cord insulation must
be intact with no cracks or deterioration.
Plug connectors must be undamaged.
DO NOT use multiple cords.
S Close the inlet cover and make sure it
is latched closed.
S Re-install the blower tube. Refer to
ATTACHING THE BLOWER TUBE for
instructions on how to attach this item.
SELECT AN EXTENSION CORD
Use only a 120 A.C. voltage supply as
shown on nameplate of the unit to
power your blower.
MINIMUM WIRE GAUGE
RECOMMENDATIONS
D To reduce the risk of electrical shock,
this equipment has a polarized plug
(one blade is wider than the other) and
will require the use of a polarized
extension cord. The appliance plug
will fit into a polarized extension cord
only one way. If the plug does not fit
fully into the extension cord, reverse
the plug. If the plug still does not fit,
obtain a correct polarized extension
cord. A polarized extension cord will
require the use of a polarized wall
outlet. This plug will fit into the
VOLTS
25 FT.
50 FT.
100 FT.
120
16
A.W.G.*
16
A.W.G.*
14
A.W.G.*
*American Wire Gauge
Secure the extension cord to the unit by
threading the cord through the cord re-
tainer (see illustration). Insert the cord
receptacle into the recessed plug.
polarized wall outlet only one way. If
plug does not fit fully into the wall
outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to
install the proper wall outlet. Do not
change the equipment plug, extension
cord receptacle, or extension cord
plug in any way.
Cor
Rec
sed
lug
Unit
Co
Re
The extension cord used to reach the
power source must be:
D Specifically marked as suitable for out-
door use. The cord must be marked with
the suffix “W-A” (in Canada “W”).
USING YOUR UNIT
STARTING YOUR UNIT
WARNING: You MUST make
sure the tubes are secure before using
the unit.
Your unit has two run positions, LOW
and HIGH. Slide the switch to one of
these positions to turn on the unit.
OPERATING POSITION
WARNING: Do not use the unit
without the tubes or collection bag
properly attached to avoid flying debris
and/or impeller contact which can
cause serious injury. Always wear eye
protection to prevent rocks or debris
from being blown or ricocheting into
the eyes and face which can result in
blindness or serious injury.
Eye Protection
Eye Protection
STOPPING YOUR UNIT
Slide the ON/OFF switch to the OFF
position.
Blower
Vacuum
7
Download from Www.Somanuals.com. All Manuals Search And Download.
USING YOUR UNIT AS A BLOWER
USING YOUR UNIT AS A VACUUM
WARNING: Do not vacuum
stones, gravel, metal, broken glass,
etc., to avoid severe damage to the im-
peller. To avoid the possibility of elec-
trical shock, do not attempt to vacuum
water or other liquids.
WARNING: Inspect the area be-
fore using the unit. Remove all debris
and hard objects such as rocks, glass,
wire, etc., that can ricochet, be thrown,
or otherwise cause injury or damage
during operation.
Use your unit as a vacuum to pick up
dry material such as leaves, grass,
small twigs, and bits of paper.
Use your unit as a blower for:
D Sweeping debris or grass clippings from
driveways, sidewalks, patios, etc.
D Blowing grass clippings, straw, or
leaves into piles, or removing debris
from corners, around joints, or between
bricks.
Direct air flow by directing the blower
tube down or to one side. Always work
away from solid objects such as walks,
large stones, vehicles, and fences.
Clean corners by starting in corners and
moving outward. This will help prevent
an accumulation of debris which could
fly into your face.
D
For best results during vacuum use,
operate your unit at high speed.
Move slowly back and forth over the
material as you vacuum. Avoid forc-
ing the unit into a pile of debris as
this can clog the unit.
D
D
Keep the vacuum tube about an inch
above the ground for best results.
WARNING: If the unit becomes
clogged, stop the unit and unplug the
extension cord. Wait until the impeller
has completely stopped turning, then
remove the vacuum tubes. Carefully
reach into the vacuum opening and
clear out the clogged debris.
Be careful when working near plants.
The force of the air could damage
tender plants.
MAINTENANCE
the OFF position. Make sure motor
stops; then restart motor and continue.
S Inlet Cover -- Discontinue use of unit if
inlet cover fails to latch properly or if it is
damaged in any way.
WARNING: Disconnect power
source before performing mainte-
nance.
GENERAL RECOMMENDATIONS
AFTER EACH USE
The warranty on this unit does not cover
items that have been subjected to opera-
tor abuse or negligence. To receive full
value from the warranty, the operator must
maintain unit as instructed in this manual.
Various adjustments will need to be made
periodically to properly maintain your unit.
INSPECT AND CLEAN UNIT & LABELS
Stop unit and unplug extension cord.
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit
using a damp cloth with a mild deter-
gent.
S Wipe off unit with a clean dry cloth.
CLEAN COLLECTION BAG
BEFORE EACH USE
IMPORTANT: THE COLLECTION BAG
MUST BE PROPERLY EMPTIED.
D You must properly empty and maintain
the collection bag to avoid deterioration
and obstruction of air flow.
D Remove the collection bag from the unit
and empty after each use. Do not store
bag without emptying the bag of all con-
tents (grass, leaves, etc.).
D Wash the bag once a year. Remove the
bag from the blower and turn the bag in-
side out. Wash the bag with a water
hose. Allow the bag to hang and dry
completely before you reuse the bag.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Inlet Cover
S Blower Tube
S Vacuum Tubes
S Collection Bag
CHECK FOR DAMAGED OR
WORN PARTS
Contact your authorized service dealer
for replacement of damaged or worn
parts.
S ON/OFF Switch -- Ensure switch func-
tions properly by moving the switch to
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE
HOW TO REMOVE AN OBJECT
FROM THE AIR INTAKE
er must be held open through all re-
maining steps.
S Carefully reach into the vacuum open-
ing and clear out the air intake area.
Clear all debris from impeller.
S Inspect the impeller for cracks. If
cracked or damaged, do not use the
unit. Have parts replaced by your autho-
rized service dealer. Do not attempt to
replace them yourself.
WARNING: Stop the unit and
disconnect from the power source be-
fore opening the inlet cover. The mo-
tor must be stopped and the impeller
blades no longer turning to avoid seri-
ous injury from the rotating blades.
S While holding the inlet cover open, re-
move the vacuum tubes. The inlet cov-
STORAGE
er source.
WARNING: Perform the follow-
ing steps after each use:
S Clean the entire unit before lengthy stor-
age.
S Stop unit and disconnect from the pow-
er source.
S Open inlet cover and clean any dirt,
grass, or debris that has collected. In-
spect the blower and all tubes. Close
and make sure the cover is latched.
S Clean air vents and air inlet of debris.
S Store your unit and extension cord in a
well ventilated area and covered, if pos-
sible, to prevent dust and dirt accumula-
tion. Do not cover with plastic. Plastic
cannot breathe and may cause con-
densation and eventual rust or corro-
sion.
S Allow motor to cool before storing or
transporting.
S Store unit with all guards in place. Posi-
tion unit so that any sharp object cannot
accidentally cause injury.
S Store unit unplugged, well out of the
reach of children.
SEASONAL STORAGE
Prepare unit for storage at the end of
the season or if it will not be used for
30 days or more.
S Check entire unit for loose screws. Re-
place any damaged, worn, or broken
parts.
If your blower is to be stored for a period
of time:
S Stop unit and disconnect from the pow-
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect from the power sourcebefore
performing all of the recommended remedies below except remedies that re-
quire unit to be operating.
SYMPTOM CAUSE
Unit fails to 1. Switch in the OFF position.
REMEDY
1. Slide switch to ON position.
2. Reconnect extension cord.
operate.
2. Extension cord discon--
nected.
3. Reset circuit breaker or
fuse.
4. Contact your authorized
service dealer.
1. Contact your authorized
service dealer.
3. Circuit breaker tripped, or
fuse blown.
4. Mechanical failure
Unit
vibrates
abnormally.
1. Mechanical failure
Impeller will
not turn
freely.
1. Debris in air intake area.
2. Mechanical failure.
1. Clean unit. Remove any
debris.
2. Contact your authorized
service dealer.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS,
cover predelivery setup or normal ad-
INC., warrants to the original purchaser justments explained in the instruction
that each new Weed Eater brand elec- manual.
tric or cordless product is free from de-
fects in material and workmanship and
agrees to repair or replace under this
warranty any defective Weed Eater
brand electric or cordless product within
two (2) years from the original date of
purchase.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
If your Weed Eater brand electric or
cordless product should fail within the
limited warranty period, return it, com-
plete, prepaid, with proof of purchase, to
the dealer from whom it was purchased
for repair or replacement at the option of
ELECTROLUX HOME PRODUCTS,
INC.
This warranty is not transferable and APPLY TO YOU.
does not cover damage or liability
caused by improper handling, improper
maintenance or the use of accessories
and/or attachments not specifically rec-
ommended by ELECTROLUX HOME
PRODUCTS, INC., for this tool. Addi-
tionally, this warranty does not cover
parts that will wear and require replace-
ment with reasonable use during the
warranty period. This warranty does not
The policy of ELECTROLUX HOME
PRODUCTS, INC., is to continuously
improve its products. Therefore, ELEC-
TROLUX HOME PRODUCTS, INC., re-
serves the right to change, modify, or
discontinue models, designs, specifica-
tions, and accessories of all products at
any time without notice or obligation to
any purchaser.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|