Owners Guide
ꢀ DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flames.
3. Open lid
Liquid Propane Gas
4. If odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department.
Leaking gas may cause a fire or explosion
which can cause serious bodily injury or
death, or damage to property.
®
®
R
W
E
ꢀ WARNING
1. Do not store spare liquid propane
cylinder within 10 feet (3m) of this
appliance.
B
E
E
B
E
W
R
R
W
E
B
E
E
B
E
W
R
2. Do not store or use gasoline or other
flammable liquids or vapors within 25
feet (8m) of this appliance.
ꢀ WARNING: Follow all leak-check
procedures carefully in this manual prior
to barbecue operation. Do this even if the
barbecue was dealer-assembled.
NOTICE TO INSTALLER:These
instructions must be left with the owner
and the owner should keep them for future
use.
THIS GAS APPLIANCE IS DESIGNED FOR
OUTDOOR USE ONLY.
YOU MUST READ THIS OWNERS GUIDE
BEFORE OPERATING YOUR GAS GRILL
ꢀ WARNING: Do not try to light this
appliance without reading the “Lighting”
Instructions section of this manual
A127.c
B018.a
C016.c
D002.g
55059 05/16/01
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Weber-Stephen Products Co. (Weber) hereby warrants There are no other express warrants except as set forth
to the ORIGINAL PURCHASER of this Weber Gas Grill herein and any applicable implied warranties of
that it will be free of defects in material and
workmanship from the date of purchase as follows:
merchantability and fitness are limited in duration to the
period of coverage of this express written Limited
Warranty. Some regions do not allow limitation on how
long an implied warranty lasts, so this limitation may not
apply to you.
Weber is not liable for any special, indirect or
consequential damages. Some regions do not allow the
exclusion or limitation of incidental or consequential
damages, so this limitation or exclusion may not apply
to you.
Weber does not authorize any person or company to
assume for it any other obligation or liability in
connection with the sale, installation, use, removal,
return, or replacement of its equipment; and no such
representations are binding on Weber.
Aluminum Castings, lifetime, 1 year paint
Porcelain Hood Section, 25 years
Porcelain Side Table, 25 years
Burners, 10 years
Igniter, 3 years
Cooking Grates, 7 years no rust through
Flavorizer Bars, 5 years no rust through
Thermoplastic Parts, 10 years
All Remaining Parts, 5 years,
when assembled and operated in accordance with the
printed instructions accompanying it.
Weber may require reasonable proof of your date of
purchase. THEREFORE, YOU SHOULD RETAIN
YOUR SALES SLIP OR INVOICE.
This Warranty applies only to products sold at retail.
WEBER-STEPHEN PRODUCTS CO.
Customer Service Center
1890 Roselle Road, Suite 308
Schaumburg, IL 60195
USA
This Limited Warranty shall be limited to the repair or
replacement of parts that prove defective under normal
use and service and which on examination shall
indicate, to Weber’s satisfaction, they are defective.
Before returning any parts, contact the Customer
service representative in your region using the contact
information sheet provided with your manual. If Weber
confirms the defect and approves the claim, Weber will
elect to replace such parts without charge. If you are
required to return defective parts, transportation
charges must be prepaid. Weber will return parts to the
purchaser, freight or postage prepaid.
This Limited Warranty does not cover any failures or
operating difficulties due to accident, abuse, misuse,
alteration, misapplication, vandalism, improper
installation or improper maintenance or service, or
failure to perform normal and routine maintenance,
including but not limited to damage caused by insects
within the burner tubes, as set out in this owner’s
manual.
LP Cylinder
The LP cylinder manufacturer is responsible for the
materials, workmanship and performance of the
cylinder. If the cylinder has a defect, malfunctions, or
you have a question regarding the cylinder, call the
cylinder manufacturer’s customer service center. The
phone number is on the warning decal, which is
permanently attached to the cylinder. If the cylinder
manufacturer has not resolved the issue to your
satisfaction, then call Weber-Stephen Products Co.,
Customer Service Center.
Deterioration or damage due to severe weather
conditions such as hail, hurricanes, earthquakes or
tornadoes, discoloration due to exposure to chemicals
either directly or in the atmosphere, is not covered by
this Limited Warranty.
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Danger & Warnings ....................................................................... A-2
Warranty........................................................................................ A-3
General Instructions ...................................................................... A-5
Exploded View............................................................................... A-6
Parts List ....................................................................................... A-10
Assembly Instructions ................................................................... B-1
Installing work surfaces and gas supply Guidelines...................... C-1
Operating ...................................................................................... D-1
Lighting.......................................................................................... D-1
Manual Lighting ............................................................................. D-2
Cooking ......................................................................................... D-3
Storage and/or Nouse ................................................................... D-3
Cleaning ........................................................................................ D-3
Refilling the LP Cylinder ................................................................ D-4
Safe handling tips for LP Gas Cylinders.......................................... D-5
Annual Maintenance ..................................................................... D-7
General Maintenance .................................................................... D-8
Replacing Main Burners................................................................ D-9
Crossover Ignition System Operations .......................................... D-10
Troubleshooting ............................................................................. D-11
A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage
General Instructions
•
The gas must be turned OFF at the LP cylinder
Your Weber Gas Barbecue is a portable outdoor
cooking appliance. With the Weber Gas Barbecue you
can grill, barbecue, roast and bake with results that are
difficult to duplicate with indoor kitchen appliances.
The closed lid and Flavorizer® Bars produce that
“outdoor” flavor in the food.
when the Weber Gas Barbecue is not in use.
When the Weber Gas Barbecue is stored indoors,
the gas supply must be disconnected and the LP
cylinder stored outdoors in a well-ventilated space.
LP cylinders must be stored outdoors in a well-
ventilated area out of the reach of children.
Disconnected LP cylinders must not be stored in a
building, garage or any other enclosed area.
When the LP cylinder is not disconnected from the
Weber Gas Barbecue, the appliance and LP
cylinder must be kept outdoors in a well-ventilated
space.
•
•
•
The Weber Gas Barbecue is portable so you can
easily change its location in your yard or on your patio.
Portability means you can take your Weber Gas
Barbecue with, if you move.
Liquid Propane (LP) gas supply is easy to use and
gives you more cooking control than charcoal fuel.
•
These instructions will give you the minimum
requirements for assembling your Weber Gas
Barbecue. Please read the instructions carefully
before using your Weber Gas Barbecue. Improper
assembly can be dangerous.
Operating
ꢀ WARNING: Only use this barbecue outdoors in a
well-ventilated area. Do not use in a garage,
building, breezeway or any other enclosed area.
ꢀ WARNING: Never use your Weber Gas Barbecue
under an unprotected combustible roof or
overhang.
•
•
Not for use by children.
If there are local codes that apply to portable gas
grills, you will have to conform to them. If there are
no local codes, you must conform to the latest
edition of the National Fuel Gas Code: ANSI Z
223.1.
ꢀ WARNING:Your Weber Gas Barbecue is not
intended to be installed in or on recreational
vehicles and/or boats.
•
•
The pressure regulator supplied with the Weber
Gas Barbecue must be used. This regulator is set
for 10.5 inches of water column (pressure).
This Weber Gas Barbecue is designed for use with
liquid propane (LP) gas only. Do not use with
natural (piped in city) gas. The valves, orifices,
hose and regulator are for LP gas only.
Do not use with charcoal fuel.
Check that the area under the control panel and
the bottom tray are free from debris that might
obstruct the flow of combustion or ventilation air.
The areas around the LP cylinder must be free
and clear from debris.
ꢀ WARNING: Do not use combustible materials
within 24 inches of the top, bottom, back or sides
of the grill.
ꢀ WARNING:The entire cooking box gets hot
when in use. Do not leave unattended.
ꢀ WARNING: Keep any electrical supply cord and
the fuel supply hose away from any heated
surface.
ꢀ WARNING: Keep the cooking area clear of
flammable vapors and liquids such as gasoline,
alcohol, etc., and combustible materials.
ꢀ WARNING: Never store an extra (spare) LP
cylinder under or near the Weber Gas Barbecue.
•
•
•
For Installation in Canada
These instructions, while generally acceptable, do not
necessarily comply with the Canadian Installation
codes, particularly with piping above and below
ground. In Canada the installation of this appliance
must comply with local codes and/or Standard CAN/
CGA-B149.2 (Installation Code for Propane Burning
Appliances and Equipment).
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Genesis Gold-B LP 051601
3
4
5
6
36
37
7
8
9
38
39
40
10
41
11
12
42
43
13
14
15
44
45
46
16
17
18
47
19
20
48
41
21
22
23
17
16
24
25
26
27
19
18
28
49
50
29
30
51
52
53
54
31
26
55
32
33
34
35
56
57
A-6
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
2.
3.
4.
5.
6.
7.
8.
Hair Pin Cotter
Hinge Pin
Left Endcap
Shroud
1/4-20 x 1 1/4 inch Bolt
Handle lock
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
Bottom Shelf
Thermometer
Right Endcap
Burner Control Knobs
Control Panel
Igniter Button
Handle
Control Panel Hardware
Crossover Tube
Front and Back Burners
Center Burner
Manifold, Hose and regulator (assembled)
Manifold Hardware
Igniter
Igniter Bracket
Back Panel
Plastic buttons
Rear Frame
Wing Nut
Cylinder Panel
Fuel Guage
Liquid Propane Cylinder
Cylinder Glides
Frame Connector
Warm-Up™ Basket
Warming Rack
Cooking Grates
Flavorizer® Bars
Cooking Box
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
1/4-20 keps nut
Slide Out Bottom Tray
Catch Pan Holder
Work Surface Trim
Work Surface
Side Frame (Right front/Left rear)
Side Frame (Left front/Right rear)
Tool holders
Nylon Retaining Washer
#8 - 16 x 7/8 screw Bolt
Catch Pan
Drip Pans
1/4 - 20 x 2 inch Bolt
Frame Connector
Nylon Washer
Front Panel
Condiment Basket
Front Frame
1/4-20 x 1/2 inch Bolt
Casters
Wheels
Hubcaps
A-7
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2001 Weber-Stephen Products Co., Weber, the silhouette, and the kettle configuration are registered trademarks
®
of Weber-Stephen Products Co., 200 East Daniels Road, Palatine, IL, 60067-6266, U.S.A. This product is covered by
one or more United States patents and patents in other nations globally. Printed in the U.S.A.
A-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove Packaging from Grill
Remove Grill from Lower Packaging
Remove all tape from packaging. Remove bottom rack
from top of packaging. Remove outer box. Pull out
bottom tray from cooking box. Remove packaging
material from bottom tray, catch pan holder, catch pan,
and drip pan.
ꢀ WARNING: Lifting the barbecue from the lower
packaging requires at least two people.
With two people: lift straight up and over lower
packaging and cardboard support.
A-9
Download from Www.Somanuals.com. All Manuals Search And Download.
You will need:
1/2 inch bolts (1/4 x 20 x 1/2 inch bolts) - 4
Phillips screwdriver
7/16 open-end or an adjustable wrench
Nylon Washers - 4
Flavorizer Bars - 5
Cooking Grates - 2
Left Work Surface - 1
Condiment basket - 1
Bottom Shelf - 1
Right Work Surface - 1
LP Cylinder - 1
Slide Out Buttom Tray - 1
Catch pan holder - 1
Catch Pan - 1
Disposable Drip Pans - 2
A-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Install the slide out bottom tray
Slide the bottom tray onto the mounting rails under the
You will need: the slide out bottom tray(1), catch pan
holder(2), catch pan and one disposable drip pan.
cooking box with finger grip toward you(1).
ƽ WARNING: Do not line bottom tray with alumi-
num foil. It can cause grease fires by trapping the
grease and not allowing grease to flow into the
catch pan.
(1)
(2)
Hook the ends of the catch pan holder into the hole in
the slide out bottom tray. The front of the catch pan
holder must be on the same side as the finger
grip(1) of the bottom tray.
(1)
Put the disposable drip pan into the catch pan.
Slide the catch pan into the catch pan holder with its
finger grip towards you(1).
(1)
B-1
B018.a
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Flavorizer® Bars and Cooking Grates
You will need: five Flavorizer Bars and two cooking
grates.
Place the Flavorizer Bars side by side in the cooking
box.
Installing the warming rack
You will need: warming rack.
Set the warming rack into the slots at the rear of the
cooking box.
Set the cooking grates onto the ledges in the cooking
box with the rounded sides up.
Install the bottom shelf
You will need: Bottom shelf.
Set the bottom shelf in place between the two frame
connectors underneath the cooking box.
Installing the Warm-Up™ Basket
You will need: Warm-Up Basket
Install the condiment basket
Place the wire hooks over the front frame to the left of
the cooking box and to the right of the control panel.
Insert one end of the Weber Warm-Up Basket into the
hole at the right side of the inside of the lid, and the
other end into the slot at the left side of the lid.
B-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing work Surfaces &
Gas Connection Guidelines
Install Left Work Surface
Check that all burner valves are off
You will need left work surface, two 1/2 inch bolts, two
nylon washers and a 7/16 inch or adjustable wrench.
Insert the left work surface tabs in the slots in the
frame(1). Slip washers on the bolts and insert the bolts
as shown(2). Tighten
You will need: burner control knobs.
Valves are shipped in the OFF position, but you should
check to be sure that they are turned OFF. Put the
knob on each valve. Check by pushing down and
turning clockwise. If they do not turn, they are off.
Proceed to the next step. If they do turn continue
turning them clockwise until they stop, then they are
off. Proceed to the next step.
(2)
(1)
Fill liquid propane cylinder
Note - The liquid propane cylinder manufacturer is
responsible for the materials, workmanship and
performance of the cylinder. If the cylinder has a
defect, malfunctions, or you have a question regarding
the cylinder, call the cylinder manufacturer’s customer
service center. The phone number is on the warning
decal, which is permanently attached to the cylinder. If
the cylinder manufacturer has not resolved the issue to
your satisfaction, then contact the Customer Service
Representative in your region using the contact
information sheet provided with your manual.
To fill, take the liquid propane cylinder and filler
adapter to an RV center or look up gas-propane in the
phone book for other sources of liquid propane gas.
ꢀ WARNING:We recommend that your liquid
propane cylinder be filled at an authorized liquid
propane gas dealer by a qualified attendant, who
fills the tank by weight.
IMPROPER FILLING IS DANGEROUS.
Tell your liquid propane dealer that this is a new liquid
propane cylinder. The air must be removed from a new
liquid propane cylinder before the initial filling.Your
liquid propane cylinder dealer is equipped to do this.
The liquid propane cylinder must be installed,
transported and stored in an upright position, and
should not be dropped or handled roughly.
Never store or transport the liquid propane cylinder
where temperatures can reach 125° Fahrenheit (too
hot to hold by hand – for example: do not leave the
liquid propane cylinder in a car on a hot day).
For full instructions on safe handling of liquid propane
cylinders, see Section “Operating”.
C-1
C016.c
Download from Www.Somanuals.com. All Manuals Search And Download.
Hang filled liquid propane cylinder on fuel gauge
Loosen the tank lock wing nut. Swing the cylinder lock
up. Tighten the wing nut so that the cylinder lock is up
and to the side. Hook the liquid propane cylinder onto
the fuel gauge. Loosen the tank lock wing nut. Swing
the tank lock down. Tighten the wing nut.
Important LP Cylinder Information
Failure to follow these DANGER statements exactly
may result in a fire causing death or serious injury.
ꢀDANGER
ꢀNEVER store a spare LP Cylinder under or near
this barbecue.
ꢀNEVER fill the tank beyond 80% full.
Your Weber gas grill is equipped with a cylinder
supply system designed for vapor withdrawal.
ꢀWARNING: Only use this grill outdoors in a well-
ventilated area. Do not use in a garage, building,
breezeway or any other enclosed area.
The LP cylinder supplied with your barbecue is
equipped with an OPD (Overfilling Prevention
Device) and a QCC1 or Type 1 (CGA810) cylinder
connection.The cylinder connection is compatible
with the barbecue connection.
This is a secondary device to prevent the overfilling of
your LP cylinder. The proper filling methods for the
filling of your cylinder are by weight or volume, as
described in NFPA 58. Please make sure your filling
station fills your LP cylinder by weight or volume. Ask
your filling station to read purging and filling
instructions on the LP cylinder before attempting to fill.
ꢀWARNING: Do not exchange the LP tank
provided with your barbecue, unless the exchange
LP tank is equipped with an OPD. Otherwise you
will lose the OPD (Overfilling Prevention Device)
feature. If there is not an LP tank available for
exchange equipped with an OPD, we recommend
that you have your LP tank filled at an authorized
LP gas dealer by a qualified attendant.
Raises up while filling
then stops when full.
C-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect filled liquid propane cylinder
Remove the control panel
ꢀ WARNING: Make sure that the cylinder valve is
closed. Close by turning clockwise.
(1) Unscrew the two phillips screws, located on the
right edge of the control panel.
Remove plastic dust cover from the fuel cylinder valve.
Screw the regulator coupling onto the tank valve(1),
clockwise, or to the right. Hand tighten only.
Note: This is a new type of connection. It tightens
clockwise and will not allow gas to flow unless the
connection is tight. The connection requires tightening
by hand only.
(2) Take off the burner control knobs.
(2)
ꢀ WARNING: Do not use a wrench to tighten the
connection. Using a wrench could damage the
regulator coupling and could cause a gas leak.
Regulator vent hole should be at 3, 6, or 9 o’clock. It
should not be pointed up.(2)
(1)
(1)
(3) Lift off the control panel.
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Check:
Check for gas leaks
ꢀ DANGER
Do not use an open flame to check for gas
leaks. Be sure there are no sparks or open
flames in the area while you check for
leaks. Sparks or open flames will result in
a fire or explosion which can cause
1) Hose to manifold connection.
ꢀ WARNING: If there is a leak a connection(1),
retighten the fitting with a wrench and recheck for
leaks with soap and water solution.
If a leak persists after retightening the fitting, turn
OFF the gas. DO NOT OPERATETHE BARBECUE.
Contact the Customer Service Representative in
your region using the contact information sheet
provided with your manual.
serious bodily injury or death and damage
to property.
2) Regulator to Cylinder connection
ꢀ WARNING:You should check for gas leaks every
time you disconnect and reconnect a gas fitting.
Note - All factory-made connections have been
thoroughly checked for gas leaks. The burners have
been flame-tested. As a safety precaution however,
you should recheck all fittings for leaks before using
your Weber Gas Barbecue. Shipping and handling may
loosen or damage a gas fitting.
ꢀ WARNING: Perform these leak checks even if
your barbecue was dealer or store assembled.
You will need: a soap and water solution, and a rag or
brush to apply it.
3) Valves to manifold connections
4) Hose to regulator connection
ꢀ WARNING: If there is a leak at connections(2,3)
or(4) turn OFF the gas. DO NOT OPERATE THE
BARBECUE Contact the Customer Service
Representative in your region using the contact
information sheet provided with your manual.
When leak checks are complete, turn gas supply OFF
at the source and rinse connections with water.
To perform leak checks: open tank valve by turning the
tank valve handwheel counterclockwise.
Check for leaks by wetting the connections with the
soap and water solution and watching for bubbles. If
bubbles form or if a bubble grows, there is a leak.
Note - Since some leak test solutions, including soap
and water, may be slightly corrosive, all connections
should be rinsed with water after checking for leaks.
ꢀ WARNING: Do not ignite burners when leak
checking.
(1)
(2)
(3)
(4)
C-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Reinstall control panel (after checking for gas
leaks)
Install Right Work Surface
You will need right work surface, two 1/2 inch bolts,
two nylon washers and a 7/16 inch or adjustable
wrench.
Insert the right work surface tabs in the slots In the
frame(1). Slip washers on the bolts and insert the bolts
as shown(2). Tighten
(1) Set the control panel in place over both sides of
the frame. Hold the crossover ignition button up
while setting the control panel in place.
(2) Line up the control panel with the white plastic
plugs in the frame brace. Insert screws and tighten
with a Phillips screwdriver until snug. Do not
overtighten.
(2)
(1)
(3) Push each of the burner control knobs onto their
valve.
(1)
(3)
(2)
C-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
ƽ DANGER:
Lighting
When the “excess gas flow control” feature is
activated, a small amount of gas I still flowing to
the burners. After turning OFF the cylinder knobs,
wait at least 5 minutes for the gas to clear before
attempting to light the barbecue. Failure to do so
may result in an explosive flame-up, which can
cause serious bodily injury or death.
3) Turn the cylinder on by turning the cylinder valve
counterclockwise.
Summary lighting instructions are on the control panel.
ƽ DANGER
Failure to open the lid while igniting the
barbecue’s burners, or not waiting 5 min-
utes to allow the gas to clear if the barbe-
cue does not light, may result in an explo-
sive flame-up which can cause serious
bodily injury or death.
ƽ WARNING: Do not lean over the open barbecue.
Keep your face and body at least one foot away
from the matchlight hole when lighting the barbe-
cue.
Crossover Ignition® System
Note - The Crossover Ignition System ignites the Front
burner with a spark from the igniter electrode inside
the Gas Catcher™ Ignition Chamber.You generate the
energy for the spark by pushing the Crossover Ignition
Button until it clicks.
ƽ WARNING: Check hose before each use of
barbecue for nicks, cracking, abrasions or cuts. If
the hose is found to be damaged in any way, do
not use the barbecue. Replace using only Weber
authorized replacement hose. Contact the Cus-
tomer Service Representative in your region using
the contact information sheet provided with your
manual.
4) Push Front burner control knob down and turn to
START/HI.
5) Push the Crossover Ignition Button several times,
so it clicks each time.
6) Check that the burner is lit by looking through the
matchlight hole on the front of the cooking box.
You should see a flame.
ƽ WARNING: If the burner does not light, turn the
Front burner control knob to OFF and wait 5
minutes to let the gas clear before you try again or
try to light with a match.
7) After the FRONT burner is lit you can turn on the
other burner or burners.
Note - Always light the FRONT burner first. The other
burner or burners ignite from the FRONT burner.
1
2
7
5
3
To Extinguish
6
Push down and turn each burner control knob
clockwise to the OFF position.Turn gas supply
OFF at the source.
4
*The grill illustrated may have slight differences than
the model purchased.
1) Open the lid.
2) Make sure all burner control knobs are turned
OFF. (Push control knob down and turn clockwise
to ensure that it is in the OFF position.)
ƽ WARNING:The burner control knobs must be in
the OFF position before turning on the liquid
propane cylinder tank valve. If they are not in the
OFF position, when you turn on the LP cylinder
valve, the “excess gas flow control” feature will
activate, limiting the flow of gas from the LP
cylinder. If this should occur, turn OFF the LP
cylinder valve and burner control knobs.Then start
over.
D-1
D002.e
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Turn the cylinder on by turning the cylinder valve
counterclockwise.
Manual Lighting
4) Strike a match and put the flame into the
matchlight hole in the front of the cooking box.
ƽ WARNING: Do not lean over open barbecue.
Keep your face and body at least one foot away
from the matchlight hole when lighting the barbe-
cue.
5) Push Front burner control knob down and turn to
START/HI.
6) Check that the burner is lit by looking through the
matchlight hole on the front of the cooking box.
You should see a flame
ƽ WARNING: If the burner does not light, turn the
Front burner control knob to OFF and wait 5
minutes to let the gas clear before you try again or
try to light with a match.
7) After the FRONT burner is lit you can turn on the
other burner.
ƽ DANGER
Failure to open the lid while igniting the
barbecue’s burners, or not waiting 5 min-
utes to allow the gas to clear if the barbe-
cue does not light, may result in an explo-
sive flame-up which can cause serious
bodily injury or death.
1) Open the lid.
2) Make sure all burner control knobs are turned
OFF. (Push each knob down and turn clockwise to
ensure they are in the off position.)
ƽ WARNING:The burner control knobs must be in
the OFF position before turning on the liquid
propane cylinder valve. If they are not in the OFF
position, when you turn on the LP cylinder valve,
the “excess gas flow control” feature will activate,
limiting the flow of gas from the LP cylinder. If this
should occur, turn OFF the LP tank valve and
burner control knobs.Then start over.
Note - Always light the FRONT burner first. The other
burner or burners ignite from the FRONT burner.
ƽ DANGER
When the “excess gas flow control” fea-
ture is activated, a small amount of gas is
still flowing to the burners. After turning
OFF the cylinder and burner control
knobs, wait at least 5 minutes for the gas
to clear before attempting to light the
barbecue. Failure to do so may result in
an explosive flame-up, which can cause
serious bodily injury or death.
To Extinguish
Push down and turn each burner control knob
clockwise to the OFF position.Turn gas supply
OFF at the source.
1
2
7
3
4,6
5
*The grill illustrated may have slight differences than
the model purchased.
D-2
Download from Www.Somanuals.com. All Manuals Search And Download.
■ The Weber Gas Barbecue should be checked for
gas leaks and any obstructions in the burner tubes
before using. (See Sections: “General Maintenance
and Annual Maintenance.”)
■ Check that the areas under the control panel and
the slide out bottom tray are free from debris that
might obstruct the flow of combustion or ventilation air.
■ The Spider Stopper ™ Guards should also be
checked for any obstructions. (See Section: “Annual
Maintenance.”)
Cooking
ƽ WARNING: Do not move the Weber Gas Barbe-
cue when operating or while barbecue is hot.
You can adjust the FRONT and BACK burners as
desired. The control settings: High (H), Medium (M),
Low (L), or Off (O) are described in your Weber
cookbook. The cookbook uses these notations to
describe the settings of the FRONT and BACK burn-
ers. For example, to sear steaks, you would set all
burners at H (high). Then to complete cooking, you
would set FRONT and BACK at M (medium). Refer to
your Weber cookbook for detailed cooking instructions.
Cleaning
ƽ WARNING:Turn your Weber Gas Barbecue OFF
and wait for it to cool before cleaning.
Note: The temperature inside your cooking box for the
first few uses, while surfaces are still very reflective,
may be hotter than those shown in your cookbook.
Cooking conditions. Such as wind and weather, may
require the adjustment of the burner controls to obtain
the correct cooking temperatures.
ƽ CAUTION: Do not clean your Flavorizer® Bars or
cooking grates in a self-cleaning oven.
For availability of replacement cooking grates and
Flavorizer Bars contact the Customer Service
Representative in your region using the contact
information sheet provided with your manual.
Outside surfaces - Use a warm soapy water solution
to clean, then rinse with water.
ƽ CAUTION: Do not use oven cleaner, abrasive
cleansers (kitchen cleansers) cleaners that contain
citrus products, or abrasive cleaning pads on
barbecue or cart surfaces.
Slide out Bottom tray - Remove excess grease, then
wash with warm soapy water, then rinse
Flavorizer® Bars and Cooking Grates - Clean with a
suitable brass bristle brush. As needed, remove from
grill and wash with warm soapy water, then rinse with
water.
ƽ CAUTION: Replace thermometer in lid when not
in use. Do not leave thermometer in food while
cooking.
If burners go out during cooking, open lid, turn off
all burners and wait five minutes before relighting.
Preheating - Your Weber Gas Barbecue is an energy-
efficient appliance. It operates at an economical low
BTU rate. To preheat: after lighting, close lid and turn
all burners to high (HH). Preheating to between 500°
and 550° F (260° and 290° C) will take 10 to 15
minutes depending on conditions such as air tempera-
ture and wind.
Catch pan - Disposable foil trays are available, or you
can line the catch pan with aluminum foil. To clean the
catch pan, wash with warm soapy water, then rinse.
Thermometer - Wipe with warm soapy water; clean
with plastic scrub ball. Do not put in dishwasher or
submerge in water.
Drippings and grease - The Flavorizer® Bars are
designed to “smoke” the correct amount of drippings
for flavorful cooking. Excess drippings and grease will
accumulate in the catch pan under the slide out bottom
tray. Disposable foil drip pans are available that fit the
catch pan.
Inside cooking module - Brush any debris off of
burner tubes. DO NOT ENLARGE BURNER PORTS
(OPENINGS). Wash inside of cooking box with warm
soapy water and a water rinse.
ƽ WARNING: Check the bottom tray for grease
build-up before each use. Remove excess grease
to avoid a grease fire in the slide out bottom tray.
Inside Lid - While lid is warm, wipe inside with paper
towel to prevent grease build-up. Flaking built-up
grease resembles paint flakes.
Stainless steel surfaces - Wash with a soft cloth and
a soap and water solution.
Thermoset surfaces - Wash with a soft cloth and a
soap and water solution.
Do not use cleaners that contain acid, mineral
spirits or xylene. Rinse well after cleaning.
Storage and/or Nonuse
■ The gas must be turned off at the liquid propane
cylinder when the Weber Gas Barbecue is not in use.
■ When the Weber Gas Barbecue is stored indoors,
the gas supply must be DISCONNECTED and the LP
cylinder stored outdoors in a well-ventilated space.
■ LP cylinder must be stored outdoors in a well -
ventilated area out of reach of children. Disconnected
LP cylinder must not be stored in a building, garage or
any other enclosed area.
Thermoset work surfaces are not to be used as
cutting boards.
■ When the LP cylinder is not disconnected from the
Weber Gas Barbecue, the appliance and LP tank must
be kept outdoors in a well-ventilated space.
D-3
Download from Www.Somanuals.com. All Manuals Search And Download.
This is a secondary device to prevent the overfilling of
your LP cylinder. The proper filling methods for the
filling of your cylinder are by weight or volume, as
described in NFPA 58. Please make sure your filling
station fills your LP cylinder by weight or volume. Ask
your filling station to read purging and filling instruc-
tions on the LP cylinder before attempting to fill.
ƽWARNING: Do not exchange the LP tank pro-
vided with your barbecue, unless the exchange LP
tank is equipped with an OPD. Otherwise you will
lose the OPD (Overfilling Prevention Device)
feature. If there is not an LP tank available for
exchange equipped with an OPD, we recommend
that you have your LP tank filled at an authorized
LP gas dealer by a qualified attendant.
Refilling the Liquid Pro-
pane Cylinder
We recommend that you refill the LP cylinder before it
is completely empty.
Removal of the LP cylinder
1) Close cylinder valve (turn clockwise).
2) Unscrew regulator coupling by turning counter-
clockwise, by hand only.
3) Loosen cylinder lock wing nut and turn cylinder
lock up out of the way.
4) Lift cylinder off.
To refill, take LP cylinder to a “Gas Propane” dealer.
ƽ WARNING:We recommend that your LP cylinder
be filled at an authorized LP gas dealer, by a
qualified attendant, who fills the cylinder by
weight. IMPROPER FILLING IS DANGEROUS.
ƽ CAUTION:When transporting the LP cylinder
make sure the plastic dust cover is in place over
the valve.This will keep dust and dirt from the
threaded portion of the valve.
(1)
(3)
(2)
Raises up while filling
then stops when full.
Connecting the Liquid Propane Cylinder
ƽ WARNING: Make sure that the LP cylinder valve
is closed. Close by turning valve clockwise.
Important LP Cylinder Information
Failure to follow these DANGER statements exactly
may result in a fire causing death or serious injury.
ƽDANGER
ƽNEVER store a spare LP Cylinder under or near
this barbecue.
ƽ DANGER
Do not use an open flame to check for gas
leaks. Be sure there are no sparks or open
flames in the area while you check for
leaks. Sparks or flames will result in a fire
or explosion which can cause serious
bodily injury or death, and damage to
ƽNEVER fill the tank beyond 80% full.
Your Weber gas grill is equipped with a cylinder
supply system designed for vapor withdrawal.
ƽWARNING: Only use this grill outdoors in a well-
ventilated area. Do not use in a garage, building,
breezeway or any other enclosed area.
property.
You will need: LP cylinder, a soap and water solution
and a rag or brush to apply it.
1) Turn the LP cylinder so the opening of the valve is
either to the front, side or rear of the Weber Gas
Barbecue. Lift and hook the cylinder onto the fuel
guage.
The LP cylinder supplied with your barbecue is
equipped with an OPD (Overfilling Prevention
Device) and a QCC1 or Type 1 (CGA810) cylinder
connection.The cylinder connection is compatible
with the barbecue connection.
D-4
Download from Www.Somanuals.com. All Manuals Search And Download.
7) Check for leaks by wetting the fitting with the soap
and water solution and watching for bubbles. If
bubbles form, or if a bubble grows, there is a leak.
2) Loosen the cylinder lock wing nut. Swing the
cylinder lock down. Tighten the wing nut.
To Connect the hose to the cylinder:
3) Remove the plastic dust cover from the valve.
4) Screw the regulator coupling onto the tank valve,
clockwise, or to the right. Hand-tighten only.
Note: This is a new type of connection. It tightens
clockwise and will not allow gas to flow unless the
connection is tight. The connection requires tightening
by hand only.
If there is a leak, turn off the gas and tighten the fitting.
Turn the gas back on and recheck with the soap and
water solution.
If leak does not stop, Contact the Customer Service
Representative in your region using the contact
information sheet provided with your manual. Do not
use the barbecue.
8) When leak checking is complete, turn gas supply
OFF at the source and rinse connections with
water.
ƽ WARNING: Do not use a wrench to tighten the
connection. Using a wrench could damage the
regulator coupling and could cause a leak.
5) Mix soap and water.
6) Turn on the cylinder valve.
Liquid Propane Cylinder
The liquid propane cylinder manufacturer is respon-
sible for the materials, workmanship and performance
of the tank. If the tank has a defect malfunctions, or
you have a question regarding the tank, call the tank
manufacturer’s customer service center. The phone
number is on the warning decal, which is permanently
attached to the tank. If the tank manufacturer has not
resolved the issue to your satisfaction, then contact
the Customer Service Representative in your region
using the contact information sheet provided with your
manual.
D-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Liquid Propane (LP) Cylinder(s)
Safe handling tips for
Liquid Propane Gas Cyl-
inders
■ The joint where the hose connects to the LP cylinder
must be leak tested each time the LP cylinder is
reconnected. For example, test each time the LP
cylinder is refilled.
■ Be sure the regulator is mounted with the small vent
hole pointed downward so that it will not collect water.
This vent should be free of dirt, grease, bugs etc.
■ The LP cylinder and connections supplied with your
Weber Gas Barbecue have been designed and tested
to meet government, American Gas Association, and
Underwriters Laboratories requirements.
■ Liquid Propane (LP) gas is a petroleum product as
are gasoline and natural gas. LP gas is a gas at
regular temperatures and pressures. Under moderate
pressure, inside a cylinder, LP gas is a liquid. As the
pressure is released, the liquid readily vaporizes and
becomes gas.
■ LP gas has an odor similar to natural gas. You
should be aware of this odor.
(1)
■ LP gas is heavier than air. Leaking LP gas may
collect in low areas and prevent dispersion.
■ To fill, take the LP cylinder to an RV center, or look
up “gas-propane” in the phone book for other sources
of LP gas.
ƽ WARNING:We recommend that your LP cylinder
be filled at an authorized LP gas dealer, by a
qualified attendant, who fills the tank by weight.
IMPROPER FILLING IS DANGEROUS.
DOT 4BA240
00/00
ƽ WARNING: If you exchange your LP cylinder,
make sure you get a similar tank in return.Your LP
cylinder is equipped with a quick closing coupling
or type 1 valve and an OPD (Overfilling Prevention
Device). Other LP cylinders may not be compatible
with your barbecue connection.
■Air must be removed from a new LP cylinder before
the initial filling. Your LP dealer is equipped to do this.
■ The LP cylinder must be installed, transported and
stored in an upright position. LP cylinders should not
be dropped or handled roughly.
■ Never store or transport the LP cylinder where
temperatures can reach 125° F (too hot to hold by
hand - for example: do not leave the LP cylinder in a
car on a hot day).
Note - A refill will last about 20 hours of cooking time
at normal use. The fuel scale will indicate the propane
supply so you can refill before running out.You do not
have to run out before you refill.
■ Treat “empty” LP cylinders with the same care as
when full. Even when the LP tank is empty of liquid
there still may be gas pressure in the cylinder. Always
close the cylinder valve before disconnecting.
ƽ CAUTION:When transporting the LP cylinder
make sure the plastic dust cover is in place over
the valve.This will keep dust and dirt from the
threaded portion of the valve.
(2)
Liquid Propane Cylinder requirements
■ Replacement LP cylinders supplied by Weber satisfy
the above requirements. Check to be sure other
cylinders have a D.O.T. certification(1), and date
tested(2) is within five years. Your LP gas supplier can
do this for you.
If you have questions about spare LP cylinders
contact the Customer Service Representative in
your region using the contact information sheet
provided with your manual.
■All LP tank supply systems must include a collar to
protect the cylinder valve.
■ The LP cylinder must be a 20-lb. size (18 1/4 inches
high, 12 1/4 inches in diameter).
■ The LP cylinder must be constructed and marked in
accordance with the specifications for LP gas cylinders
of the U.S. Department of Transportation (D.O.T.).
■ Do not use a damaged LP cylinder. Dented or rusty
LP cylinders or LP cylinders with a damaged valve
may be hazardous and should be replaced with a new
one immediately.
D-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact the Customer Service Representative in
your region using the contact information sheet
provided with your manual.
Annual Maintenance
After a period of nonuse, we recommend that you
perform the following maintenance procedures for your
safety.
Check:
3) Valves-to-manifold connections.
ƽ WARNING: Check the hose before each use of
the barbecue for nicks, cracking, abrasions or
cuts. If the hose is found to be damaged in any
way, do not use the barbecue. Replace using only
Weber authorized replacement hose. Contact the
Customer Service Representative in your region
using the contact information sheet provided with
your manual.
4) The hose-to-regulator connection.
ƽ WARNING: If there is a leak at connections (2),
(3) or (4), turn OFF the gas. DO NOT OPERATE
THE BARBECUE. Contact the Customer Service
Representative in your region using the contact
information sheet provided with your manual.
When leak checks are complete, turn gas supply OFF
at the source and rinse connections with water.
■ Inspect the burners for correct flame pattern. Clean
if necessary, following the procedures outlined in the
“General Maintenance” section of this manual.
■ Check all gas fittings for leaks.
ƽ DANGER
Do not use an open flame to check for gas
leaks. Be sure there are no sparks or open
flames in the area while you check for
leaks. Sparks or flames will result in a fire
or explosion, which can cause serious
bodily injury or death, and damage to
(1)
(2)
property.
ƽ WARNING:You should check for gas leaks every
time you disconnect and reconnect a gas fitting.
Note - All factory-made connections have been
thoroughly checked for gas leaks. The burners have
been flame tested. As a safety precaution however,
you should recheck all fittings for leaks before using
your Weber Gas Barbecue. Shipping and handling may
have loosened or damaged a gas fitting.
(3)
ƽ WARNING: Perform these leak checks even if
your barbecue was dealer- or store-assembled.
You will need: a soap and water solution and a rag or
brush to apply it.
To perform leak checks: Make sure all Burners are in
the off position. Turn on gas supply.
(4)
ƽ WARNING: Do not ignite burners while leak
checking.
Check for leaks by wetting the connections with the
soap and water solution and watching for bubbles. If
bubbles form, or if a bubble grows, there is a leak.
Note - Since some leak test solutions, including soap
and water, may be slightly corrosive, all connections
should be rinsed with water after checking for leaks.
Inspection and Cleaning of the Weber
Spider Stopper™ Guards
To inspect the Spider Stopper Guards, remove the
control panel and look to see if they have dust or dirt
on their outside surfaces. If they are dirty, brush off the
outside surface of the Spider Stopper Guards with a
soft bristle brush (an old toothbrush for example).
Check that there are no gaps in the Spider Stopper
Guards’ seams or in the fit around the burners or
valves. (See Section “General Maintenance.”)
Check:
1) Hose-to-manifold connection.
2) Regulator-to-Cylinder connection.
ƽ WARNING: If there is a leak at connection (1),
retighten the fitting with a wrench and recheck for
leaks with soap and water solution.
If a leak persists after retightening the fitting, turn
OFF the gas. DO NOT OPERATETHE BARBECUE.
D-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Burner Flame Pattern
The Weber Gas Barbecue burners have been factory
set for the correct air and gas mixture. The correct
flame pattern is shown.
1) Burner tube
2) Tips occasionally flicker yellow
3) Light blue
General Maintenance
Weber Spider Stopper™ Guards
Your Weber Gas Barbecue, as well as any outdoor gas
appliance, is a target for spiders and other insects.
They can nest in the venturi section (Venturi(1), air
shutter(2), venturi fin(3) ) of the burner tubes. This
blocks the normal gas flow, and can cause the gas to
flow back out of the air shutter. This could result in a
fire in and around the air shutters, under the control
panel, causing serious damage to your barbecue.
4) Dark blue
(1)
(1)
(2)
(3)
(4)
If the flames do not appear to be uniform throughout
the burner tube, follow the burner cleaning procedures.
(2)
(3)
The Weber Spider Stopper™ Guard(1) is factory
installed. It fits tightly around the air shutter section of
the burner tube and the valve, thereby preventing
spiders and other insects access to the burner tubes
through the air shutter openings.
Main Burner Cleaning Procedure
Turn off the gas supply. Remove the manifold.
Look inside each burner with a flashlight.
(1)
Clean the inside of the burners with a wire (a straight-
ened-out coat hanger will work). Check and clean the
air shutter opening at the ends of the burners. Check
and clean the valve orifices at the base of the valves.
Use a brass bristle brush to clean outside of burners.
This is to make sure all the burner ports are fully open.
CAUTION: Do not enlarge the burner ports when
cleaning.
We recommend that you inspect the Weber Spider
Stopper Guards at least once a year. (See Section
“Annual Maintenance”.) Also inspect and clean the
Spider Stopper Guards if any of the following
symptoms should ever occur:
1) The smell of gas in conjunction with the burner
flames appearing yellow and lazy.
2) Barbecue does not reach temperature.
3) Barbecue heats unevenly.
4) One or more of the burners do not ignite.
ƽ DANGER
Failure to correct the above mentioned
symptoms may result in a fire, which can
cause serious bodily injury or death, and
cause damage to property.
D-8
Download from Www.Somanuals.com. All Manuals Search And Download.
7) Lift and twist the burner assembly slightly, to
separate the crossover tube(1) from the burners.
Remove the burners from the cooking box.
Replacing Main Burners
1) Your Weber Gas Barbecue must be OFF and cool.
2) Turn gas OFF at source.
3) To remove control panel: take off the burner
control knobs. Remove the screws holding the
control panel in place. Lift off the control panel.
4) Unlatch the Spider Stopper™ Guards and remove
them.
(1)
8) To reinstall the burners, reverse 3) through 7).
ƽ CAUTION:The burner openings(1) must be
positioned properly over the valve orifices(2).
Check proper assembly before fastening manifold in
place.
5) Remove the manifold bracket and unscrew the two
wing nuts(1) that hold the manifold to the cooking
box. Pull the manifold and valve assembly out of
the burners and carefully set it down.
(2)
(1)
(1)
6) Slide the burner assembly out from under the
guide screw and washer(1) in the corners of the
cooking box.
(1)
D-9
Download from Www.Somanuals.com. All Manuals Search And Download.
9) Reinstall the Spider Stopper Guards. Slightly
rotate the Spider Stopper Guards so that the
seams are in line with the Venturi fins(1). There
should be no gaps in the seams or in the fit around
the burners(2) and valves(3).
Crossover® Ignition System Operations
If the Crossover Ignition System fails to ignite the Left
burner, light the Left burner with a match. If the Left
burner lights with a match, then check the Crossover
Ignition System.
■ Check that both the white(1) and black(2) ignition
wires are attached properly.
(1)
(3)
(1)
(2)
(2)
ƽ CAUTION: If the Spider Stopper Guards do not
fit tightly, contact the Customer Service Represen-
tative in your region using the contact information
sheet provided with your manual.
ƽ WARNING: After reinstalling the gas lines, they
should be leak checked with a soap and water
solution before using the barbecue. (See Step:
“Check for gas leaks.”)
■ Check that the Crossover Ignition button pushes the
igniter (button) down, and returns to the up position.
■ Check to see if the igniter is loose in the frame.
Tighten if necessary; See Step “Install igniter” for
correct procedure.
If the Crossover Ignition System still fails to light,
Contact the Customer Service Representative in your
region using the contact information sheet provided
with your manual.
D-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check
Cure
Burners burn with a yellow or
orange flame, in conjunction with Guards for possible obstructions.
the smell of gas.
Inspect Weber Spider Stopper
Clean Weber Spider Stopper
Guards. (See Section “Annual
Maintenance”)
(Blockage of holes.)
The excess flow satety device,
which is part of the barbecue to
cylinder connection, may have
activated.
To reset the excess flow safety
device turn all burner control knobs
and the cylinder valve OFF.
Disconnect the regulator from the
cylinder. Turn burner control knobs to
HIGH. Wait at least 1 minute. Turn
burner control knobs OFF. Reconnect
the regulator to the cylinder. Turn
cylinder valve on slowly. Refer to
“Lighting Instructions”.
Burners do not light. -or- Burners
have a small flickering flame in
the HIGH position. -or-
Barbecue temperature only
reaches 250˚ to 300˚ in the HIGH
position.
Burner does not light, or flame is
low in HIGH position.
Is LP fuel low or empty?
Refill LP cylinder.
Is fuel hose bent or kinked?
Straighten fuel hose.
Does the Front burner light with a
match?
If you can light the Front burner with
a match, then check the Crossover
Ignition System.
Experiencing flare-ups:
Are you preheating barbecue in the All burners on high for 10 to 15
prescribed manner?
minutes for preheating.
Are the cooking grates and
Flavorizer bars heavily coated with
burned-on grease?
Clean thoroughly. (See Section
“Cleaning”)
ƽ CAUTION: Do not line the
bottom tray with aluminum foil.
Is the bottom tray “dirty” and not
allowing grease to flow into catch
pan?
Clean bottom tray
Burner flame pattern is erratic.
Flame is low when burner is on
HIGH. Flames do not run the
whole length of the burner tube.
Are burners clean?
Clean burners. (See Section
“General Maintenance”.)
Inside of lid appears to be
“peeling.” (Resembles paint
peeling.)
The lid is porcelain-on-steel, not
Clean thoroughly. (See Section
paint. It cannot “peel”. What you are “Cleaning”.)
seeing is baked on grease that has
turned to carbon and is flaking off.
THIS IS NOT A DEFECT.
If problems cannot be corrected by using these methods, please contact the Customer
Service Representative in your region using the contact information sheet provided with
your manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
|