MODELS 9140, 9140S, 9150, 9170, 9190 AND 9210
HIGH PERFORMANCE AIRLESS SPRAYER
OWNER’S MANUAL • READ THIS MANUAL FOR COMPLETE INSTRUCTIONS
TABLE OF CONTENTS:
This pump is available in two models: a
stand model and a cart model. The cart
model is shown in this manual. All
information given for the cart model
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
COMPONENTS AND DESCRIPTION . . . . . . . . . . . . . . . . . . 4
SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PLUGGING IN THE SPRAYER. . . . . . . . . . . . . . . . . . . . . . . 6
PRESSURE RELIEF PROCEDURE . . . . . . . . . . . . . . . . . . . 6
PURGING AND PRIMING. . . . . . . . . . . . . . . . . . . . . . . . . . . 7
applies to the stand model except where
indicated.
SPRAYING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SPRAYING TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . 9
CLEANUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
FLUID SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-51
WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Need help? Call us first for answers fast.
Call Wagner Spray Tech toll-free if you have any
comments or problems with this product.
1-800-880-0993
Wagner Technical Service
Visit us on the world wide web!
1770 Fernbrook Lane, Minneapolis, MN 55447
SPECIFICATIONS:
Weight .............................. 25 lbs (9140S)
31 lbs (9140, 9150)
Generator .........................15 amp A/C
36 lbs (9170, 9190)
40 lbs (9210)
Spraying pressure ............Up to 2800 PSI
Safety features .................Spray gun trigger lock and guard;
built-in tip safety guard; priming
Capacity ...........................Up to .25 gallon (1 liter) per minute (9140,
9140S, 9150)
knob for safe pressure release.
Up to .33 gallon (1.25 liter) per minute (9170)
Up to .42 gallon (1.6 liter) per minute (9190)
Up to .45 gallon (1.71 liter) per minute (9210)
Capability..........................Sprays a variety of paints, oil
base, latex, primers, stains,
preservatives and other
nonabrasive materials.
Do not use materials with flash
points below 70°F (21°C).
Power source ...................1/2 Hp universal motor (9140, 9140S, 9150)
5/8 Hp permanent magnet DC motor (9170)
3/4 Hp permanent magnet DC motor (9190)
7/8 Hp permanent magnet DC motor (9210)
This pump should not be used with textured materials,
block filler, or asphalt sealer.
Power requirement...........15 amp minimum circuit on 115 VAC, 60
Hz current
0803 • Form No. 0512731G
Printed in the U. S. A.
U.S. Patent No. 6,435,846
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION • READ ALL SAFETY
INFORMATION BEFORE OPERATING THE EQUIPMENT
HAZARD: GENERAL
Can cause severe injury or property damage.
GROUNDING INSTRUCTIONS
This product must be grounded. In the event of an electrical
short circuit, grounding reduces the risk of electric shock by
providing an escape wire for the electric current. This product
is equipped with a cord having a grounding wire with an
appropriate grounding plug. The plug must be plugged into an
outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
PREVENTION:
• Read all instructions and safety precautions before
operating equipment.
• Follow all appropriate local, state, and national codes
governing ventilation, fire prevention, and operation.
• The United States Government Safety Standards have
been adopted under the Occupational Safety and Health
Act (OSHA). These standards, particularly part 1910 of
the General Standards and part 1926 of the Construction
Standards should be consulted.
• Use only manufacturer authorized parts. User assumes
all risks and liabilities when using parts that do not meet
the minimum specifications and safety requirements of the
pump manufacturer.
• Before each use, check all hoses for cuts, leaks, abrasion
or bulging of cover. Check for damage or movement of
couplings. Immediately replace the hose if any of these
conditions exist. Never repair a paint hose. Replace it
with another grounded high-pressure hose.
WARNING
Improper installation of the grounding plug
can result in a risk of electric shock.
If repair or replacement of the cord or plug is
necessary, do not connect the green grounding wire to either
flat blade terminal. The wire with insulation having a green
outer surface with or without yellow stripes is the grounding
wire and must be connected to the grounding pin.
Check with a qualified electrician or serviceman if the
grounding instructions are not completely understood, or if you
are in doubt as to whether the product is properly grounded.
Do not modify the plug provided. If the plug will not fit the
outlet, have the proper outlet installed by a qualified electrician.
• All hoses, swivels, guns, and accessories must be
pressure rated at or above 2800PSI/193 BAR.
This product is for use on a nominal 120 volt circuit and has a
grounding plug that looks like the plug illustrated below. Make
sure that the product is connected to an outlet having the
same configuration as the plug. No adapter should be used
with this product.
• Do not spray outdoors on windy days.
• Wear clothing to keep paint off skin and hair.
IMPORTANT ELECTRICAL INFORMATION
Grounded Outlet
CAUTION
Use only a 3-wire extension cord that has a 3-blade grounding
plug and a 3-slot receptacle that will accept the plug on the
product. Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage resulting in loss
of power and overheating. A 14 or 12 gauge cord is
Grounding Pin
Cover for grounded outlet box
recommended. If an extension cord is to be used outdoors, it
must be marked with the suffix W-A after the cord type
designation. For example, a designation of SJTW-A would
indicate that the cord would be appropriate for outdoor use.
IF YOU EXPERIENCE PROBLEMS WITH YOUR
SPRAYER AT ANY TIME DURING ASSEMBLY,
OPERATION OR CLEANUP, PLEASE REFER TO
THE TROUBLESHOOTING SECTION OF THIS
MANUAL (PAGE 15), OR CALL CUSTOMER
SERVICE AT:
Do not use more than 100 feet of hose. If you need to
paint further than 100 feet from your power source,
use more extension cord, not more paint hose.
1-800-880-0993
CAUTION
THE 9140, 9140S AND 9150 SERIES UNITS ARE
PROVIDED WITH A NON-RESETABLE THERMAL
OVERLOAD. THE 9170, 9190 AND 9210 SERIES UNITS
ARE PROVIDED WITH A REPLACEABLE FUSE.
• Always disconnect the motor from the power supply
before working on the equipment.
The cause of the overload should be corrected before
restarting. Take to Service Center.
© 2003 Wagner Spray Tech - All rights reserved. 1-800-880-0993
3
English
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS AND DESCRIPTION
sprayer model (refer to Spray
COMPONENTS
Gun/Tip Chart, below).
The shipping carton for your painting system contains the following:
• Suction set and return tube
Spray Hose ......................The spray hose connects the gun to
the pump.
• Spray gun with filter
• Spray tip assembly (see chart below)
• 25 foot long, 1/4 inch diameter pressure hose (9140, 9140S, 9150)
• 50 foot long, 1/4 inch diameter pressure hose (9170, 9190, 9210)
• Separating Oil
Return Tube......................Fluid is sent back out through the
return tube to the original container.
PRIME/SPRAY Knob........The PRIME/SPRAY knob directs fluid
to the spray hose when set to SPRAY
or the return tube when set to PRIME.
The arrows on the PRIME/SPRAY
CONTROLS AND FUNCTIONS
knob shows the rotation directions for
PRIME and SPRAY.
ON/OFF Switch................The ON/OFF switch turns the unit on
and off (O=OFF, l=ON).
The PRIME/SPRAY knob is also used
to relieve pressure built up in the
spray hose (Pressure Relief
Procedure, page 6)
Suction Set.......................Fluid is drawn through the suction
set into the pump.
Fluid Section ....................A piston in the fluid section moves up
and down to create the suction that
Pressure Control Dial.......The pressure control dial controls
the amount of force the pump uses
to push the fluid (see graphic below
for locations).
draws fluid through the suction set.
Spray Gun........................The spray gun controls the delivery
of the fluid being pumped. The gun
model you have depends on your
Spray Gun/Tip Chart
Pressure Control Dial
Sprayer Gun
Tip
Max.
Size
Recommended
Filter
Model Model Size
Rear of motor shroud,
Front face plate,
(9140, 9140S, 9150,
9140/S GX-06 .013
.015
.015
.017
Yellow (fine)
Yellow (fine)
Yellow (fine)
9210 model
9170, and 9190).
9150
9170
9190
9210
GX-07 .013
GX-07 .015
GX-08 .017
GX-10 .017
Spray hose
port
.019 White (medium)
.021 White (medium)
Hose
bracket
Handle
Pressure Control Dial
Motor
housing
PRIME/SPRAY knob
Lubricating
area (on front
face plate)
PRIME position SPRAY position
PRIME
ON/OFF switch
O = OFF
Pail bracket
Spray hose
l = ON
Y A S P R
PRIME/
SPRAY
knob
Spray
tip
Spray
gun
Fluid
section
Return
tube
O
Suction
tube
Suction set screen
Customer Service: 800-880-0993
4
© 2003 Wagner Spray Tech - All rights reserved.
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP--ASSEMBLING THE SPRAYER
TOOLS NEEDED FOR SETUP
ATTACHING THE SPRAY GUN
1. Thread spray gun
onto the other end
of the hose.
• Two adjustable wrenches
• 3/16” allen wrench
• Extension cord (refer to Important Electrical Information
(page 3).
Hold the gun with
one adjustable
wrench, and tighten
with the other.
ATTACHING THE SUCTION SET & RETURN TUBE
WARNING
Do not plug in the unit until setup is complete.
1. Attach the suction tube to the inlet valve and tighten firmly
by hand. Be sure that the threads are straight so that the
fitting turns freely.
2. Press the return tube onto the return tube fitting.
3. Squeeze clip over the return tube fitting to secure return
tube.
ATTACHING THE HANDLE (CART MODELS)
1. Position the handle
against the cart so that
the holes in the handle
line up with the holes in
the cart.
Return tube
fitting
2. Insert the bolts through
the holes in the handle
and cart and locking
washers.
3. Tighten the wing nuts
onto the bolts by hand.
Inlet valve
Clip
Return tube
Suction set
LOCKING AND UNLOCKING THE SPRAY GUN
ATTACHING THE PAIL BRACKET (CART MODELS)
WARNING
Always lock the trigger off when attaching the spray tip or
when the spray gun is not in use. Refer to Spray Gun/Tip
Chart on page 4 to determine the gun model you have.
1. Position the pail bracket
against the unit so that
the holes in the unit line
up with the holes in the
bracket.
2. Insert the bolts through the
holes in the bracket and
the unit.
GX-06/07
GUN MODELS GX-06 AND
GX-07
The gun is secured when the
trigger lock is at a 90° angle
(perpendicular) to the trigger in
either direction.
3. Tighten the bolts with a
3/16” allen wrench.
ATTACHING THE PAINT HOSE
Gun locked
(gun will not spray)
GX-08/10
1. Thread the high pressure
hose to the paint hose
port.
GUN MODELS GX-08 AND
GX-10
2. Tighten with an adjustable
wrench.
3. Remove pusher stem
from inlet valve.
To lock the gun, turn the trigger
lock forward and slightly down
until it stops.
Gun locked
(gun will not spray)
The spray tip SHOULD NOT be attached until after the
sprayer and paint hose have been purged and primed.
© 2003 Wagner Spray Tech - All rights reserved.
5
Customer Service: 800-880-0993
English
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
CHOOSING THE CORRECT SPRAY GUN FILTER
Use the proper gun filter based on the tip size being used.
This column contains instructions that will be repeated
throughout this manual.
Part No. Tip Size
Filter
Type
Mesh
Number
Color of Qty.
Filter
Body
PLUGGING IN THE SPRAYER
0154918 .011
Extrafine 180 mesh red
0.084 mm
2 pack
2 pack
2 pack
1. Check that the ON/OFF
switch is in the OFF
position.
0154675 .013 - .015 Fine
100 mesh yellow
0.140 mm
0154842 .017 - .023 Medium
50 mesh
white
2. Plug the sprayer into a
heavy duty grounded
extension cord. Refer to
Important Electrical
Information, page 3).
0.315 mm
BEFORE YOU PRIME THE SPRAYER
Before priming, squirt a teaspoon of separating oil (P/N
0154908 included with unit) into the indicated area. Light
household oil can be substituted if necessary. Do not put
more than a teaspoon into the lubricating area. Too much oil
will leak down into your paint.
PRESSURE RELIEF PROCEDURE
WARNING
Be sure to follow the pressure relief procedure (page 6)
when shutting the unit off FOR ANY PURPOSE. This
procedure is used to relieve pressure from the spray hose.
1. Lock the spray gun off.
GX-06/07
GX-08/10
IF YOUR UNIT IS NEW. . .
All units are performance-tested at the factory and are shipped
with test fluid in the fluid section to prevent corrosion during
shipment and storage.
2. Flip the ON/OFF switch to
the OFF (O) position.
• Whether you are going to spray latex or oil-based
paints, this fluid must be purged and thoroughly cleaned
out of the system (follow Purging and Priming the Pump
steps, page 7).
3. Unlock the spray gun,
turn the PRIME/SPRAY
knob to PRIME, and
trigger spray gun into
paint bucket.
IF YOUR UNIT HAS ALREADY BEEN USED. . .
If the pump has already been used you will need to purge the
water or solvent used in cleanup and storage.
4. Lock the spray gun.
PAINT STRAINING
It is recommended that in order to avoid premature tip and gun
clogging you should strain your paint before spraying. Follow
manufacturer’s recommendations.
Customer Service: 800-880-0993
6
© 2003 Wagner Spray Tech - All rights reserved.
English
Download from Www.Somanuals.com. All Manuals Search And Download.
PURGING & PRIMING
PURGING AND PRIMING THE PUMP
PURGING AND PRIMING THE SPRAY HOSE
1. Unlock the spray gun and
turn PRIME/SPRAY knob
to PRIME.
1. Place a full container of
paint underneath the
suction tube.
Suction
tube
2. Secure the return tube
into a waste container.
Your spray tip SHOULD
NOT be attached to your
spray gun when purging
your spray hose.
Return
tube
2. Trigger and HOLD the
spray gun into a waste
container.
3. While holding the trigger,
switch the pump ON (l).
3. Turn the pressure control
dial to maximum pressure
(+).
4. While holding the trigger,
turn the PRIME/SPRAY
knob to SPRAY. Hold the
trigger until all air, water, or
solvent is purged from the
spray hose and paint is
flowing freely (read
PRIME
Y A S P R
4. Turn the PRIME/SPRAY
knob to PRIME.
warnings below).
WARNING
Keep hands clear from fluid stream.
WARNING
5. Plug in the sprayer, and
move the ON/OFF switch
to the ON position.
Using a metal container, ground
the gun by holding it against the
edge of the container while
flushing. Failure to do so may
lead to a static electric discharge
which may cause a fire.
If the PRIME/SPRAY knob is still
on SPRAY, there will be high pressure in the hose and
spray gun until the PRIME/SPRAY knob is turned to PRIME.
The unit will begin to draw paint up the suction tube,
into the pump, and out the return tube. Let the unit
cycle long enough to remove test fluid from the pump,
or until paint is coming from the return tube.
5. Release trigger, turn the
PRIME/SPRAY knob to
PRIME and turn pump
OFF (O).
6. Trigger the gun into the
waste container once more
to be sure that no pressure
is left in the hose.
6. Switch the pump to OFF (O).
7. Remove the return tube from the waste container and
place it in its operating position above the container of
paint. Use the metal clip to bind the two hoses together.
7. Lock the spray gun off.
8. Thread the spray tip guard assembly onto the gun.
Tighten by hand.
Begin
tightening
the tip at
this angle
to achieve
the desired
spray angle
when tight.
Your sprayer is now purged. Move to Purging and
Priming the Spray Hose.
Your hose is now purged and primed. You are ready to
paint.
© 2003 Wagner Spray Tech - All rights reserved.
7
Customer Service: 800-880-0993
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SPRAYING
PRACTICE
TIP:
Keep the spray gun perpendicular to the
surface, otherwise one end of the pattern will
be thicker than the other.
CAUTION
Be sure that the paint hose is free of kinks and clear of
objects with sharp cutting edges.
Approximately
10 to 12 inches
1. Switch the pump ON (l)
Right way
PRIME
and turn the
PRIME/SPRAY knob to
SPRAY.
Y A S P R
Wrong way
2. Turn the pressure contol
dial to its highest setting
(+). The spray hose
TIP:
Keep the spray gun at right angles to the
surface. This means moving your entire arm
back and forth rather than just flexing your wrist.
should stiffen as paint
begins to flow through it.
3. When the motor shuts off, unlock the spray gun and spray
a test area to check the spray pattern.
Light Coat
Heavy Coat
Light Coat
When enough pressure has built up in the hose, the
motor will shut off automatically. The motor will cycle
on and off automatically as it needs pressure.
The pressure control
dial can be adjusted up
or down to achieve the
desired spray pattern.
Good spray pattern
Do not flex wrist while spraying.
TIP:
The spray gun should be triggered by turning it
on and off with each stroke. Do not trigger the
gun during the middle of a stroke. This will result
in an uneven spray and splotchy coverage.
Paint tailing pattern
SPRAYING TECHNIQUE
The key to a good paint job is an even coating over the entire
surface. This is done by using even strokes. Follow the TIPS,
below.
Proper way to trigger the spray gun
TIP:
Keep your arm moving at a constant speed and
keep the spray gun at a constant distance from
the surface. The best spraying distance is 10 to
12 inches between the spray tip and the surface.
Keep stroke
even
Approximately
10 to 12 inches
Even coat throughout
Start stroke
Pull trigger
Keep steady
Release trigger End stroke
Approximately
10 to 12 inches
ADDITIONAL TIPS
Overlap each stroke by about 30%. This will ensure an
even coating.
When you stop painting, follow PRESSURE RELIEF
PROCEDURE.
IF YOU EXPECT TO BE AWAY FROM YOUR SPRAYER
FOR MORE THAN ONE HOUR, FOLLOW THE SHORT-
TERM CLEANUP PROCEDURE DESCRIBED IN THE
STORAGE SECTION OF THIS MANUAL (page 12).
Keep stroke smooth and at an even speed.
Customer Service: 800-880-0993
8
© 2003 Wagner Spray Tech - All rights reserved.
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SPRAYING TROUBLESHOOTING
CLEANING THE SPRAY GUN FILTER
This filter must be cleaned every time you
use your sprayer.
When using thicker paints, the filter might
need to be cleaned more often.
The following is a short list of minor difficulties you might
encounter while spraying. If any of these occur, it will
reduce the flow of paint, making your spray pattern poor, or
paint will fail to spray from the gun.
Filter top
Pin hole
• Clogged spray tip
• Clogged gun filter
• Clogged suction set screen
1. Perform Pressure Relief Procedure
(page 6).
Follow the guidelines on this page to correct any one of
these problems.
2a. If you have a model GX-06/07 spray
gun, unscrew the fitting from the
bottom of the spray gun using an
adjustable wrench, making sure not to
lose the spring.
2b. If you have a model GX-08/10 spray gun, unclip the
trigger guard from the filter housing by pulling outward
from the filter housing. Unscrew the housing.
UNCLOGGING THE SPRAY TIP
WARNING
Do not attempt to unclog or clean the tip with your finger.
GX-08/10
Housing
CAUTION
Do not use a needle or other sharp pointed instrument to
clean the tip. The hard tungsten carbide can chip.
If the spray pattern becomes distorted or stops completely
while the gun is triggered, follow these steps:
1. Release the trigger and lock the gun off.
Filter
GX-06/07
Filter
Spring
Trigger
guard
GX-06/07
Fitting
Housing
3. Remove filter from spray gun housing and clean with the
appropriate cleaning solution (warm, soapy water for latex
paints, mineral spirits for oil-based materials).
4. Inspect the filter for holes (see Hole picture, above).
Replace if holes are found.
GX-08/10
2. Rotate the reversible tip arrow 180° so that the point of
CAUTION
the arrow is toward the rear of the gun (CLEAN position).
NEVER POKE THE FILTER WITH A SHARP INSTRUMENT!
5. Replace the cleaned filter, tapered end first, into the gun
housing.
Under pressure, the spray tip
may be very difficult to turn.
Turn the PRIME/SPRAY knob
to PRIME and trigger the gun.
This will relieve pressure and
the tip will turn more easily.
The tapered end of the filter must be loaded properly
into the gun. Improper assembly will result in a
plugged tip or no flow from the gun.
6a. For the GX-06/07, replace the spring and the fitting.
3. Turn the PRIME/SPRAY knob
to SPRAY.
Tighten with an adjustable wrench.
6b. For the GX-08/10, replace the housing and snap the
trigger guard back into the housing.
4. Unlock the gun and squeeze
the trigger, pointing the gun at
a scrap piece of wood or
CLEANING THE SUCTION SET SCREEN
cardboard. This allows
pressure in the spray hose to
blow out the obstruction.
When the nozzle is clean, paint
will come out in a straight, high pressure stream.
The screen at the bottom of the suction set may also need
cleaning. Check it every time you change paint buckets.
1. Remove the screen by pulling it out
of the retainer with a plier.
2. Clean the screen with the
If paint still will not spray from the spray tip, follow the
other steps on the next column.
appropriate cleaning solution (warm,
soapy water for latex paints, mineral
spirits for oil-based paints).
5. Release the trigger and lock the gun off.
6. Reverse the tip so the
arrow points forward
again (SPRAY position).
7. Unlock the gun and
resume spraying.
If after having completed all of the steps on this page
you are still experiencing problems spraying, refer to the
TROUBLESHOOTING guide (page 15).
© 2003 Wagner Spray Tech - All rights reserved.
9
Customer Service: 800-880-0993
English
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANUP
PURGING THE PAINT HOSE
CLEANING THE SUCTION SET
IMPORTANT CLEANING
NOTES!
1. Lock the gun and turn
the pump OFF (O).
2. Remove the suction
hose and return tube
and clean it using the
appropriate cleaning
solution.
These steps will allow you to
recover excess paint left over in the
paint hose.
READ THESE NOTES AND
WARNINGS BEFORE YOU
START TO CLEAN YOUR
SPRAYER!
1. Lock the gun and remove spray tip
assembly.
2. Submerge suction set into a bucket
with appropriate cleaning solution.
You should also wipe the threads of
the inlet valve, and remove and
clean the suction set screen.
3. When suction set is clean, thread the
suction tube back onto the inlet
valve, and replace the return tube
onto the return tube fitting. Replace
clip.
• When using latex paints, clean
your sprayer and components
using warm, soapy water.
When using oil-based paints,
use mineral spirits.
3. Hold the spray gun against the side of
the paint can and hold the trigger.
• Do not use mineral spirits on
latex paint, or the mixture will
turn into a jelly-like substance
which is difficult to remove.
Return tube
fitting
Inlet valve
Clip
Return tube
• No matter which cleaning
solution you use, make sure to
dispose of it properly when
finished cleaning your sprayer.
Suction set
4. While holding the trigger, turn the
pump ON (l), and turn the
• Thorough cleaning and
lubrication of the sprayer is
the most important step you
can take to ensure proper
operation after storage.
4. Submerge the suction set into a
PRIME/SPRAY knob to SPRAY.
bucket of NEW cleaning solution.
PRIME
Y A S P R
CALL
1-800-880-0993
IF YOU HAVE ANY QUESTIONS
REGARDING THE CLEANUP OF
YOUR SPRAYER
Let the pump run until all paint is
purged from the hose and cleaning
solution is coming out of the gun.
5. Turn the PRIME/SPRAY knob to
PRIME, turn the pump to ON (l), and
trigger the gun into a waste container
to relieve the pressure.
5. Release the trigger.
WARNING
6. Hold the spray gun against the side of
a separate container and hold the
trigger.
Special cleanup instructions for use with
flammable solvents:
• ALWAYS FLUSH SPRAY GUN AT
LEAST ONE HOSE LENGTH
AWAY FROM SPRAY PUMP.
• If collecting flushed solvents in
one gallon metal container, place
it into an empty five gallon
container, then flush.
6. Let the pump circulate the cleaning
solution through the suction set for 2-
3 minutes.
7. Turn the pump OFF (O).
8. Move on to Cleaning the Spray
7. Trigger the gun until the fluid coming
out of the gun is clear.
8. Turn the PRIME/SPRAY knob to
PRIME and trigger gun once more to
relieve pressure.
• Area must be free from vapors.
• Follow all cleanup instructions.
Gun, next page.
9. Move on to Cleaning the Suction
Set.
Customer Service: 800-880-0993 10
© 2003 Wagner Spray Tech - All rights reserved.
English
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANUP (CONTINUED)
CLEANING THE SPRAY GUN FILTER AND TIP ASSEMBLY
1. Make sure the pump is switched OFF (O), the
PRIME/SPRAY knob is turned to PRIME, and unplug the
sprayer.
5 Clean spray tip and filter with a soft-bristled brush and the
appropriate cleaning solution. Be sure to remove and
clean the washer and saddle seat located in the rear of
the spray tip assembly.
2. Remove spray gun from the paint hose using adjustable
wrenches.
Saddle Washer
seat
6. Reassemble spray gun:
• install gun filter tapered-end first, and
GX-08/10
Housing
Filter
GX-06/07
Filter
Spring
Trigger
guard
Fitting
Housing
3. Remove filter from spray gun (refer to Cleaning the
Spray Gun Filter, page 9).
• install spray tip, saddle seat and washer, and replace
spray guard assembly.
GX-08/10
Housing
Filter
GX-06/07
Filter
Spring
Trigger
guard
Fitting
Housing
7. Thread the spray gun back onto the paint hose. Tighten
with a wrench.
4. Remove spray tip from spray guard assembly.
IMPORTANT!
Continue cleaning instructions on next column
If you used oil-based paints, you must flush the pump
again using warm, soapy water to prepare it for
storage. Repeat Cleaning the Suction Set instructions.
© 2003 Wagner Spray Tech - All rights reserved.
11
Customer Service: 800-880-0993
English
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
SHORT-TERM STORAGE (UP TO 16 HOURS) PREPARING THE SPRAYER FOR LONG-
TERM STORAGE
Follow these steps when using latex paints only. If
using materials that are oil-based, follow the long-term
storage steps.
1. Fill a cup or other container with separating oil
(approximately 2 ounces) supplied with the unit and
submerge the inlet valve into the oil.
SHUTDOWN
1. Lock the spray gun off.
GX-06/07
GX-08/10
2. Turn the PRIME/SPRAY knob to PRIME.
2. Place a rag over the spray hose port, and turn the switch
ON (l).
3. When the oil has been sucked from the cup, switch the
pump OFF.
4. Insert the pusher stem into the inlet valve. Make sure the
pusher stem is inserted fully.
3. Switch the pump OFF, and unplug the sprayer.
Inlet
valve
The pusher stem is designed to do two things:
4. Pour 1/2 cup water slowly on the top of the paint to
prevent the paint from drying.
5. Wrap the spray gun assembly in a damp cloth and place it
in a plastic bag. Seal the bag shut.
6. Place the sprayer in a safe place out of the sun for short-
term storage.
• It holds the oil in the valve to keep the carbide
seat from rusting.
• Secondly, it will keep the ball off of the seat to
prevent any paint residue deposits that will cause
the ball to stick to the seat. Paint deposits or rust
formed on the carbide seat will cause priming and
operation problems during repeated uses.
STARTUP
5. Wipe the entire unit, hose and gun with a damp cloth to
remove accumulated paint.
6. Replace the high pressure hose to the paint hose port.
1. Remove the gun from the plastic bag.
2. Stir the water into the paint.
3. Check to be sure that the PRIME/SPRAY knob is set to
PRIME.
4. Plug sprayer in and
PRIME
turn the switch to
ON.
5. Turn the
Y A S P R
PRIME/SPRAY
knob to SPRAY.
6. Test the sprayer on
a practice piece and begin spraying.
Customer Service: 800-880-0993 12
© 2003 Wagner Spray Tech - All rights reserved.
English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
ACCESSORIES
Part #
Description
DAILY MAINTENANCE
0154908
0154830
0270192
0291000
0279667
0088154
0508910
0508914
0152001
0155206
0152307
0155208
0152310
0512181
0512180
0512179
0512182
0501010
0512508
0279974
0279976
0512134
0508931
0154832
0512500
0512501
0512502
0512503
0501419
0512504
0512505
0512506
0093930
0156113
0089959
0089958
0279109
Separating Oil
The only daily maintenance necessary is thorough cleaning.
Follow the cleaning procedures in this manual.
Hose, Whip End, 5’ x 3/16”
Hose, Wireless, 25’ x 1/4"
Hose, Wireless, 50’ x 1/4"
Hose Connector, 1/4” x 1/4”
Pressure Gauge
EXTENDED MAINTENANCE
Some pump parts eventually wear out from use and must be
replaced. The following list indicates the available repair kits
for the parts replaced by each kit. However, pump
performance is the only reliable indicator of when to replace
wear parts. Refer to the Troubleshooting section for more
information on when to use these kits.
Tip Extension, 12”
Tip Extension, 24”
Power Roller Gun Attachment
9" Roller Cover, 3/8” Nap
9" Roller Cover, 1/2” Nap
9" Roller Cover, 3/4” Nap
9" Roller Cover, 1-1/4” Nap
GX-08 Four Finger Metal Airless Spray Gun
GX-07 Two Finger Metal Airless Spray Gun
GX-06 Two Finger Plastic Airless Spray Gun
GX-10 Two Finger Metal Airless Spray Gun w/Swivel
Guard Assembly, F-Thread
Guard Assembly, G-Thread
3 Foot Pole Extension w/Swivel
6 Foot Pole Extension w/Swivel
180 Degree Swivel
Kit Part #
Description
0512228
0512222
0512229
0512224
Fluid Section Seal Kit (9140, 9140S, 9150)
Valve Replacement Kit (9140, 9140S, 9150)
Fluid Section Seal Kit (9170, 9190, 9210)
Valve Replacement Kit (9170, 9190, 9210)
CLEANING THE INLET VALVE
Cleaning or servicing the inlet valve may be required if
the unit has priming problems. This may be caused by
improper cleaning and/or storage.
F- to G-Thread Adapter
Suction Set Filter (2 Pack)
411 Trade Spray Tip
413 Trade Spray Tip
1. Unscrew the inlet valve
assembly from the unit
with a crescent wrench.
415 Trade Spray Tip
417 Trade Spray Tip
419 Trade Spray Tip
Housing
2. Unscrew the inlet nut
using a 3/8 inch allen
wrench.
515 Trade Spray Tip
517 Trade Spray Tip
Inlet valve
assembly
519 Trade Spray Tip
Inlet nut
Anti-Seize Compound
3. Remove excess paint or
TR-10 Telescoping Roller, 9", 3/8" Nap
Yellow Gun Filter
White Gun Filter
rust from the ball and seat or replace with new parts from
kit P/N 0512222 (9140, 9140S, 9150) or P/N 0512224
(9170, 9190, 9210). You may also have to clean excess
paint inside the housing.
Pump Saver Plus Protector
4. Inspect the inlet O-ring on the inlet valve. Clean or
replace, and lubricate with a light household oil.
4. Reassemble ball, carbide seat, and O-rings in the order
shown below into the inlet valve.
Inlet O-ring
Inlet valve
Ball
O-ring
Carbide seat
O-ring
Inlet nut
5. Install inlet nut back into inlet valve. Torque to 12 ± 2
ft/lbs if you have torque wrench.
6. Make sure the inlet valve O-ring is installed on the inlet
valve, then install entire inlet valve assembly back into
unit. Tighten with an adjustable wrench.
© 2003 Wagner Spray Tech - All rights reserved.
13 Customer Service: 800-880-0993
English
Download from Www.Somanuals.com. All Manuals Search And Download.
FLUID SECTION SEAL REPLACEMENT INSTRUCTIONS
KIT 0512228 (MODELS 9140, 9140S, AND 9150)
KIT 0512229 (MODELS 9170, 9190, AND 9210)
WARNING
Always wear protective eye wear while servicing the pump. Be sure to follow the PRESSURE RELIEF PROCEDURE (page 6)
when shutting the unit down for any purpose, including servicing or adjusting. After performing the pressure relief
procedure, be sure to unplug the unit before servicing or adjusting. Area must be free of solvents and paint fumes.
used. Be careful not to damage the piston.
DISASSEMBLY OF THE FLUID SECTION
6. Apply any type of household grease to the piston and yoke
1. Remove the suction set.
area to prolong life. Apply to the holes in the yoke where
2. Remove the front cover and the four
screws that secure it using a T20
Torx head driver.
3. Remove the yoke screw and washer
that secures the dowel pin. The
dowel pin connects the yoke to the
piston.
4. Using the pliers, pull the dowel pin
out.
5a. For models 9140, 9140S, and 9150, rotate the pump
shaft so the piston is in the top dead center position. This
can be done by pushing on the yoke. This is required to
disassemble all the parts.
the dowel is inserted.
7. Install the dowel pin to connect the yoke to the piston. The
piston may have to be moved up or down to do this.
8. Install the yoke screw and washer to secure the dowel pin.
9. Turn pump right side up and apply a few drops of Wagner
Separating Oil or light household oil between the top nut and
piston. This will prolong the seal life.
10. Install front cover and four (4) screws.
11. Install the suction set.
0512228 Kit
(9140, 9140S
Top nut
and 9150)
5b. For models 9170, 9190, and 9210, inspect the yoke
assembly and piston. In order to remove all the necessary
parts, the piston must not be in the bottom dead center
position. If the piston is at the bottom of the stroke, install
the front cover and screws, turn the pump on briefly to
index the piston, unplug the unit, and repeat step 2.
6. Unscrew and remove the inlet valve assembly using an
adjustable wrench.
7. Remove the piston assembly by pushing down on the
piston near the yoke.
0512229 Kit
Top seal
(9170, 9190,
and 9210)
(cup down)
Yoke
Retaining
ring
8. Unscrew and remove the top nut using and adjustable
wrench.
9. Remove the worn seals using a flat head screwdriver or
punch. Remove the top seal from the top and the bottom
seal from the bottom by pressing against the side of the
seal and popping it out. Be sure not to scratch the
housing where the seals are located.
Washer
Dowel
Screw
Piston/seal
assembly
0512228 Kit
(9140, 9140S,
and 9150)
10. Clean the area where the new seals are to be installed.
ASSEMBLY OF THE FLUID SECTION
1. Lubricate the new top seal with Separating Oil (P/N
0154908) or light household oil and by hand place the seal
(cup side of seal down) into the top port of the housing.
0512229 Kit
(9170, 9190,
and 9210)
CAUTION! DO NOT
attempt to remove the
seals from the piston.
Insertion
tool
2. Place a small amount of anti-seize on the threads of the
nut. Place the top nut into the top of the housing and
tighten with an adjustable wrench. This will drive the top
seal into the correct position.
O-ring
3. Turn the pump upside down.
Lubricate the seal on the
piston/seal assembly similar to
the top seal. Place the
Inlet valve assembly
piston/seal assembly into the
bottom of the housing. Insert
the plastic insertion tool and
thread into position to properly
seat the piston/seal. Thread
fully until tight. Remove the
insertion tool.
SERVICE NOTE--MODEL 9210
The inlet check ball is a wear part. Erosion of the check
ball can result in a loss of performance similar to a worn
piston and seals. Inspect the inlet ball by removing the
inlet valve assembly. If worn, replace the assembly with
P/N 0512224. This part number is available at Wagner
authorized service centers or by calling 1-800-880-0993.
4. Install the new O-ring on the inlet valve assembly,
lubricate with Separating Oil (P/N 0154908), thread into
the bottom (inlet) of the housing, and tighten with an
adjustable wrench. This will drive the bottom seal into the
correct position.
5. Align the piston with the yoke. A rubber mallet may be
Customer Service: 800-880-0993 14
© 2003 Wagner Spray Tech - All rights reserved.
English
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
PROBLEM
A. The sprayer does not start.
CAUSE
SOLUTION
1. The sprayer is not plugged in.
2. The ON/OFF switch is set to OFF.
3. The sprayer was turned off while still under
pressure.
1. Plug the sprayer in.
2. Turn the ON/OFF switch to ON.
3. Turn pressure control knob to maximum setting (+),
or relieve pressure by turning the PRIME/SPRAY
valve to PRIME.
4. No voltage is coming from the wall plug.
5. The extension cord is damaged or has too
low a capacity.
4. Properly test the power supply voltage.
5. Replace the extension cord.
6. A fuse is blown in the sprayer.
7. There is a problem with the motor.
6. Take sprayer to Wagner Authorized Service Center.
7. Take sprayer to Wagner Authorized Service Center.
B. The sprayer starts but does
not draw in paint when the
PRIME/SPRAY knob is set to
PRIME.
1. The unit will not prime properly or has lost prime.
2. The paint bucket is empty or the suction
tube is not totally immersed in the paint.
3. The suction set is clogged.
1. Try to prime the unit again.
2. Refill the bucket or immerse the suction tube in
paint.
3. Clean the suction set.
4. The suction tube is loose at the inlet valve.
5. The inlet or outlet valve is stuck.
4. Clean the tube connection and tighten it securely.
5. Clean the inlet and outlet valves and replace any
worn parts.* Inlet may be stuck from old paint.
Insert pusher stem to release
6. The inlet valve is worn or damaged.
7. The PRIME/SPRAY valve is plugged.
6. Replace the inlet valve.*
7. Take sprayer to Wagner Authorized Service Center.
C. The sprayer draws up paint
but the pressure drops when
the gun is triggered.
1. The spray tip is worn.
2. The suction set screen is clogged.
3. The gun or spray tip filter is plugged.
1. Replace the spray tip with a new tip.**
2. Clean the suction set screen.
3. Clean or replace the proper filter. Always keep
extra filters on hand.
4. The paint is too heavy or coarse.
4. Thin or strain the paint.
5. The outlet valve assembly is dirty or worn.
6. The inlet valve assembly is damaged or worn.
5. Clean or replace the outlet valve assembly.*
6. Replace the inlet valve.*
D. The PRIME/SPRAY valve is
on SPRAY and there is flow
through the return tube.
1. The PRIME/SPRAY valve is dirty or worn.
1. Take sprayer to Wagner Authorized Service Center.
E. The spray gun leaks.
1. Internal parts of the gun are worn
or dirty.
1. Take the sprayer to a Wagner Authorized Service
Center.
F. The tip assembly leaks.
G. The spray gun will not spray.
H. The paint pattern is tailing.
1. The tip was assembled incorrectly.
2. A seal is worn.
1. Check the tip assembly and assemble properly.
2. Replace the seal.*
1. The spray tip or the gun filter is plugged.
2. The spray tip is in the CLEAN position.
1. Clean the spray tip or gun filter.
2. Put the tip in the SPRAY position.
1. The pressure is set too low.
2. The gun, the tip, or the suction filter
is plugged.
1. Increase the pressure.
2. Clean the filters.
3. The suction tube is loose at the inlet valve.
4. The tip is worn.
3. Tighten the suction tube fitting.
4. Replace the spray tip.
5. The paint is too thick.
6. Pressure loss.
5. Thin the paint.
6. Refer to Causes and Solutions for problem C.
* Special repair kits with instructions are available for these procedures. Refer to the Maintenance (page 13) section of this
manual for a list of the kits and their part numbers.
** Additional parts are available for this procedure. Refer to the Accessories (page 13) section of this manual for a list of the
parts and their part numbers.
© 2003 Wagner Spray Tech - All rights reserved.
15 Customer Service: 800-880-0993
English
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST • LISTE DE PIÈCES • LISTA DE PIEZAS
GX-06/07 (9140, 9140S, 9150, 9170) SUCTION SET • DISPOSITIF
D’ASPIRATION • JUEGO DE SUCCIÓN
1
5
2
3
1
2
3
4
5
6
(9140S)
4
ENGLISH
Description
Item
1
Part #
Quantity
ENGLISH
Description
0512120
0512121
0501011
0501413
0154675
0043590
0278357
Plastic gun assembly............................1
Metal gun assembly..............................1
Guard Assembly ...................................1
Tip*........................................................1
Filter assembly, 100 mesh....................1
Spring, filter...........................................1
Cap, filter housing.................................1
Item
Part #
Quantity
1
0512215
0512220
0512268
0512371
0512389
0512390
0154832
9885553
Suction set (9140S)..............................1
Suction set assembly (plastic)..............1
Suction set assembly (metal) ...............1
Return tube (9140S).............................1
Return tube...........................................1
Clip........................................................1
Filter......................................................1
Return tube fitting ....................................1
2
3
4
5
6
2
3
4
5
* See Accessories section (page 13)
FRANÇAIS
FRANÇAIS
Article N° de pièce Description
Quantité
Article N° de pièce
Description
Pistola en plastique et
ses composants ................................1
Pistola en métallique et
ses composants ................................1
Protège-embout et ses composants .1
Embout*.............................................1
Filtre et ses composants, maille 100 ...1
Ressort, filtre.....................................1
Capuchon, logement de filtre............1
Quantité
1
0512215
0512220
0512268
Dispositif d’aspiration et ses
1
0512120
composants (9140S)..........................1
Dispositif d’aspiration et ses
0512121
composants (plastique)......................1
Ensemble d’aspiration et ses
2
3
4
5
6
0501011
0501413
0154675
0043590
0278357
composants (métal) ...........................1
Tube de retour (9140S)
Tube de retour ...................................1
Agrafe ................................................1
2
3
0512371
0512389
0512390
4
5
0154832
9885553
Filtre ...................................................1
Raccord de tube de retour.....................1
* Se reporter à la liste d’ACCESSOIRES (page 29)
ESPAÑOL
ESPAÑOL
Article
Pieza#
Descripción
Cantidad
1
0512215
Ensamble del juego de
Artículo Pieza#
Descripción
Cantidad
succión (9140S).................................1
Ensamble del juego de
succión (plástico) ...............................1
Ensamble del juego de
succión (metal)...................................1
Tubo de retorno (9140S)....................1
Tubo de retorno .................................1
Abrazadera ........................................1
1
0512120
0512121
0501011
0501413
0154675
0043590
0278357
Ensamble de la pistola plástico ........1
Ensamble de la pistola metal............1
Esamble de protección .....................1
Boquilla*............................................1
Ensemble de filtro, malla 100 ...........1
Resorte, filtro.....................................1
Tapa, alojamiento de filtro.................1
0512220
0512268
2
3
4
5
6
2
5
0512371
0512389
0512390
4
5
0154832
9885553
Filtro ...................................................1
Conector del tubo de retorno.............1
* Consultre el listado en ACCESORIOS (página 45).
48
800-880-0993 © 2003 Wagner Spray Tech - All rights reserved.
English Français Español
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST • LISTE DE PIÈCES • LISTA DE PIEZAS
FRANÇAIS
GX-08 (9190)
ArticleN° de pièce Description
Quantity
8
7
6
5
4
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Se reporter à la liste d’ACCESSOIRES
Protège-embout....................................1
Diffuseur, 2,2 cm...................................1
Ressort de soupape .............................1
Protège-doigts ......................................1
Détente et ses composants..................1
Vis de détente (courte) .........................1
Corps du pistolet...................................1
Écrou hexagonal...................................1
Bloc de retenue ....................................1
Cheville coulissante..............................2
Vis de détente (longtemps)...................1
Filtre*...................................................1*
Rondelle................................................1
Poignée.................................................1
Ressort .................................................1
Bague d’étanchéité...............................1
Raccord ................................................1
0501011
0296261
0296270
0296230
0296285
0296284
0296228
9910201
0296222
0296286
0296287
9
10
11
12
13
2
1
14
15
0296289
0296342
0043590
0296283
0296301
16
17
18
* Se reporter au tableau de la section CHOIX DU FILTRE DE
PISTOLET APPROPRIÉ, page 22).
ENGLISH
ESPAÑOL
Item
1
Part #
Description
Refer to Accessories, page 13
Quantity
Articulo Pieza#
Descripción
Consulte Accesorios
Ensmble de la protección de
Cantidad
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
0501011
0296261
0296270
0296230
0296285
0296284
0296228
9910201
0296222
0296286
0296287
Holder assembly...................................1
Diffuser, 7/8" .........................................1
Valve spring unit ...................................1
Trigger guard ........................................1
Trigger assembly ..................................1
Trigger screw (short).............................1
Gun housing .........................................1
Hex nut .................................................1
Retainer block.......................................1
Sliding pin .............................................2
Trigger screw (long)..............................1
Filter* ..................................................1*
Washer..................................................1
Handle ..................................................1
Spring ...................................................1
Sealing ring...........................................1
Fitting....................................................1
1
2
0501011
la boquilla rociadora ............................1
Difusor 7/8” ...........................................1
Unidad del resorte de la válvula...........1
Protector del gatillo...............................1
Ensemble del gatillo .............................1
Tornillo del gatillo (corto).......................1
Alojamiento de la pistola.......................1
Tuerca hexagonal.................................1
Bloque de retención..............................1
Pasador deslizante ...............................2
Filtro*...................................................1*
Tornillo del gatillo (de largo) .................1
Arandela ...............................................1
Mango...................................................1
Resorte .................................................1
Aro sellador...........................................1
Ensemble del collarín ...........................1
3
4
5
6
7
0296261
0296270
0296230
0296285
9910403
0296228
9910201
0296222
0296286
8
9
10
11
13
12
14
15
16
17
18
0296289
0296342
0043590
0296283
0296301
0296287
0296289
0296342
0043590
0296283
0296301
*See page 6 for additional filter sizes.
*Consulte la página para 38 ver tamaños adicionales de filtros
© 2003 Wagner Spray Tech - All rights reserved. 800-880-0993
49
Español Français English
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST • LISTE DE PIÈCES • LISTA DE PIEZAS
FRANÇAIS
GX-10 (9210)
ArticleN° de pièce Description
Quantity
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Se reporter à la liste d’ACCESSOIRES
Protège-embout....................................1
Diffuseur, 2,2 cm...................................1
Ressort de soupape .............................1
Protège-doigts ......................................1
Détente et ses composants..................1
Vis de détente (courte) .........................1
Corps du pistolet...................................1
Écrou hexagonal...................................1
Bloc de retenue ....................................1
Cheville coulissante..............................2
Vis de détente (longtemps)...................1
Filtre*...................................................1*
Rondelle................................................1
Poignée.................................................1
Ressort .................................................1
Pivot......................................................1
Séparateur............................................1
0501011
0296261
0296270
0296230
0296291
0296284
0296228
9910201
0296222
0296286
0296287
8
7
6
5
4
3
9
10
11
12
13
2
1
14
15
18
0296289
0296342
0296343
0347706
0296262
16
17
* Se reporter au tableau de la section CHOIX DU FILTRE DE
PISTOLET APPROPRIÉ, page 22).
ENGLISH
ESPAÑOL
Item
1
Part #
Description
Refer to Accessories, page 13
Quantity
Articulo Pieza#
Descripción
Cantidad
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
0501011
0296261
0296270
0296230
0296291
0296284
0296228
9910201
0296222
0296286
0296287
Holder assembly...................................1
Diffuser, 7/8" .........................................1
Valve spring unit ...................................1
Trigger guard ........................................1
Trigger assembly ..................................1
Trigger screw (short).............................1
Gun housing .........................................1
Hex nut .................................................1
Retainer block.......................................1
Sliding pin .............................................2
Trigger screw (long)..............................1
Filter* ..................................................1*
Washer..................................................1
Handle ..................................................1
Spring ...................................................1
Swivel ...................................................1
Separator..............................................1
1
2
Consulte Accesorios
Ensmble de la protección de
0501011
la boquilla rociadora ............................1
Difusor 7/8” ...........................................1
Unidad del resorte de la válvula...........1
Protector del gatillo...............................1
Ensemble del gatillo .............................1
Tornillo del gatillo (corto).......................1
Alojamiento de la pistola.......................1
Tuerca hexagonal.................................1
Bloque de retención..............................1
Pasador deslizante ...............................2
Filtro*...................................................1*
Tornillo del gatillo (de largo) .................1
Arandela ...............................................1
Mango...................................................1
Resorte .................................................1
Giratorio................................................1
Separador.............................................1
3
4
5
6
7
0296261
0296270
0296230
0296291
9910403
0296228
9910201
0296222
0296286
8
9
10
11
13
12
14
15
16
17
18
0296289
0296342
0296343
0347706
0296262
0296287
0296289
0296342
0296343
0347706
0296262
*See page 6 for additional filter sizes.
*Consulte la página para 38 ver tamaños adicionales de filtros
50
800-880-0993 © 2003 Wagner Spray Tech - All rights reserved.
English Français Español
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST • LISTE DE PIÈCES • LISTA DE PIEZAS
CART ASSEMBLY
1
CHARIOT ET SES
COMPOSANTS
STAND ASSEMBLY
SUPPORT ET SES
COMPOSANTS
CONJUNTO DE CARRITO
CONJUNTO DE
SOPORTE
2
9140S
4
5
6
3
7
8
9
10
8
0512396
0512397
0278373
0275728
9890104
9885546
0294635
Roue (9140, 9150) . . . . . . . . . . . . . .2
Roue (9170) . . . . . . . . . . . . . . . . . . .2
Roue (9190, 9210) . . . . . . . . . . . . . .2
Capuchon (9140, 9150, 9170) . . . . . .2
Capuchon (9190, 9210) . . . . . . . . . .2
Bouchon (9140, 9150, 9170, 9190) . .2
Bouchon (9210) . . . . . . . . . . . . . . . .2
ENGLISH
Item Part #
Description
Quantity
9
1
0512406
0512336
Handle . . . . . . . . . . . . . . . . . . . . . . . . .1
Handle (9140S) . . . . . . . . . . . . . . . . . .1
Pail Bracket Bolt . . . . . . . . . . . . . . . . .2
Pail Bracket . . . . . . . . . . . . . . . . . . . . .1
Bolt (9140, 9150, 9170, 9190) . . . . . . .4
Bolt (9210) . . . . . . . . . . . . . . . . . . . . . .4
Washer . . . . . . . . . . . . . . . . . . . . . . . .4
Nut (9140, 9150, 9170, 9190) . . . . . . . .4
Knob Handle (9210) . . . . . . . . . . . . . . .4
Cart (9140, 9150) . . . . . . . . . . . . . . . . .1
Cart (9170) . . . . . . . . . . . . . . . . . . . . .1
Cart (9190, 9210) . . . . . . . . . . . . . . . . .1
Wheel (9140, 9150) . . . . . . . . . . . . . . .2
Wheel (9170) . . . . . . . . . . . . . . . . . . . .2
Wheel (9190, 9210) . . . . . . . . . . . . . . .2
Cap (9140, 9150, 9170) . . . . . . . . . . . .2
Cap (9190, 9210) . . . . . . . . . . . . . . . . .2
Plug (9140, 9140S, 9150, 9170, 9190) .2
Plug (9210) . . . . . . . . . . . . . . . . . . . . .2
10
2
3
4
0512355
9800108
9802518
9821503
9810111
0288661
0512383
0512368
0512385
0512396
0512397
0278373
0275728
9890104
9885546
0294635
ESPAÑOL
5
6
Articulo Pieza#
1
Descripción
Cantidad
0512406
0512336
Mango . . . . . . . . . . . . . . . . . . . . . . .1
Mango (9140S) . . . . . . . . . . . . . . . . .1
Perno del soporte del bote . . . . . . . .2
Soporte pare el bote . . . . . . . . . . . . .1
Perno (9140, 9150, 9170, 9190) . . . .4
Perno (9210) . . . . . . . . . . . . . . . . . . .4
Arandela . . . . . . . . . . . . . . . . . . . . . .4
Tuerca (9140, 9150, 9170, 9190) . . .4
Asa de perilla (9210) . . . . . . . . . . . . .4
Carrito (9140, 9150) . . . . . . . . . . . . .1
Carrito (9170) . . . . . . . . . . . . . . . . . .1
Carrito (9190) . . . . . . . . . . . . . . . . . .1
Carrito (9210) . . . . . . . . . . . . . . . . . .1
Rueda (9140, 9150) . . . . . . . . . . . . .2
Rueda (9170) . . . . . . . . . . . . . . . . . .2
Rueda (9190, 9210) . . . . . . . . . . . . .2
Tapa (9140, 9150, 9170) . . . . . . . . . .2
Tapa (9190, 9210) . . . . . . . . . . . . . . .2
Enchufe (9140, 9140S, 9150, 9170
7
2
3
4
0512355
9800108
9802518
9821503
9810111
0288661
0512383
0512368
0512385
0512425
0512396
0512397
0278373
0275728
9890104
9885546
8
5
6
9
7
10
FRANÇAIS
8
Article N° de pièce Description
Quantité
1
0512406
0512336
Guidon . . . . . . . . . . . . . . . . . . . . . . .1
Guidon (9140S) . . . . . . . . . . . . . . . .1
Boulon de support
9
2
10
de contenant . . . . . . . . . . . . . . . . . . .2
Support de contenant . . . . . . . . . . . .1
Boulon (9140, 9150, 9170, 9190) . . .4
Boulon (9210) . . . . . . . . . . . . . . . . . .4
Rondelle . . . . . . . . . . . . . . . . . . . . . .4
Écrou (9140, 9150, 9170, 9190) . . . .4
Gros écrou papillon (9210) . . . . . . . .4
Chariot (9140, 9150) . . . . . . . . . . . . .1
Chariot (9170) . . . . . . . . . . . . . . . . . .1
Chariot (9190) . . . . . . . . . . . . . . . . . .1
Chariot (9210) . . . . . . . . . . . . . . . . . .1
9190) . . . . . . . . . . . . . . . . . . . . . . . .2
Enchufe (9210) . . . . . . . . . . . . . . . . .2
3
4
0512355
9800108
9802518
9821503
9810111
0288661
0512383
0512368
0512385
0512425
0294635
5
6
7
© 2003 Wagner Spray Tech - All rights reserved. 800-880-0993
51
Español Français English
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
AIRLESS PAINT SPRAY EQUIPMENT
This product, manufactured by Wagner Spray Tech Corporation (Wagner), is warranted to the original retail purchaser against defects in material and workmanship
for one year from date of purchase.
This warranty does not cover damage resulting from improper use, accidents, user's negligence or normal wear. This warranty does not cover any defects or
damages caused by service or repair performed by anyone other than a Wagner Authorized Service Center. This warranty does not apply to accessories.
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO ONE YEAR FROM DATE OF PURCHASE.
WAGNER SHALL NOT IN ANY EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER FROM BREACH OF
THIS WARRANTY OR ANY OTHER REASON.
If any product is defective in material and/or workmanship during the applicable warranty period, return it with proof of purchase, transportation prepaid to any
Wagner Authorized Service Center. (Service Center listing is enclosed with this product.) Wagner’s Authorized Service Center will either repair or replace the product
(at Wagner’s option) and return it to you, postage prepaid.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
GARANTIE LIMITÉE
MATÉRIEL DE PULVÉRISATION DE PEINTURE SANS AIR
Ce produit, fabriqué par Wagner Spray Tech Corporation (Wagner), est garanti, au bénéfice de l’acheteur au détail d’origine, contre tout vice de matières et toute
malfaçon pour un an à compter de la date d’achat.
La présente garantie ne s'applique pas aux dégâts entraînés par une utilisation incorrecte, par la négligence de l'usager ou par l'usure normale. La présente garantie
ne s'applique pas non plus aux défectuosités ou dommages résultant de l'entretien ou de la réparation que fait une personne quelconque qui ne soit pas membre
d'un centre d'entretien autorisé pour les produits Wagner. La présente garantie ne s'applique pas aux accessoires.
TOUTE GARANTIE IMPLICITE DE QUALITÉ MARCHANDE OU D'ADAPTATION À UN USAGE PARTICULIER EST LIMITÉE À UNE PÉRIODE DE 30 JOURS
POUR UNE UTILISATION PROFESSIONNELLE OU DE LOCATION ET D'UNE ANNÉE POUR L'UTILISATION DOMESTIQUE, À COMPTER DE LA DATE
D'ACHAT.
TOUTE GARANTIE IMPLICITE DE VENDABILITÉ OU DE CONVENANCE À UNE DESTINATION PARTICULIÈRE EST LIMITÉE À UN AN À COMPTER DE LA
DATE D’ACHAT.
Si un produit est défectueux en ce qui concerne les matériaux ou l'exécution pendant la période de garantie applicable, vous devez le retourner, avec une preuve
d'achat et frais de port payés, à n'importe quel centre d'entretien autorisé pour les produits Wagner. (Une liste de ces centres d'entretien est jointe à ce produit.)
Le centre d'entretien autorisé pour les produits Wagner réparera ou remplacera le produit (à la discrétion de Wagner) et vous le retournera par la poste, avec
frais de port payés.
CERTAINES PROVINCES INTERDISENT LES RESTRICTIONS SUR LA DURÉE D'UNE GARANTIE IMPLICITE OU L'EXCLUSION DES DOMMAGES
ACCESSOIRES OU INDIRECTS. IL SE PEUT DONC QUE LA RESTRICTION ET L'EXCLUSION ÉNONCÉES CI-DESSUS NE S'APPLIQUENT PAS À VOUS.
LE PRÉSENTE GARANTIE VOUS ACCORDE DES DROITS JURIDIQUES SPÉCIFIQUES, ET VOUS AVEZ PEUT-ÊTRE D'AUTRES DROITS, QUI PEUVENT
VARIER D'UNE PROVINCE À L'AUTRE.
GARANTÍA LIMITADA
EQUIPO DE ATOMIZACIÓN DE PINTURA SIN AIRE
Este producto, fabricado por Wagner Spray Tech Corporation (Wagner), está garantizado ante el comprador original contra defectos de materiales y mano de obra
durante un año contado a partir de la fecha de compra.
Esta garantía no cubre los daños que sean resultado de un uso inapropiado, accidentes, negligencia del usuario o un desgaste normal. Esta garantía no cubre
ningún defecto o daño que haya sido causado por los servicios o reparaciones llevadas a cabo por alguien que no sea un técnico del Centro de Servicio Autorizado
de Wagner. Esta garantía no es válida para ningún accesorio.
CUALQUIER GARANTIA IMPLICITA DE COMERCIALIZACION O IDONEIDAD PARA CUALQUIER PROPOSITO EN PARTICULAR QUEDA LIMITADA A UN AÑO
A PARTIR DE LA FECHA DE COMPRA.
WAGNER NO SERÁ EN NINGÚN CASO RESPONSABLE DE NINGÚN DAÑO INCIDENTAL O DE CONSECUENCIA DE NINGUNA CLASE, QUE RESULTE DE
VIOLAR ESTA GARANTÍA O POR CUALQUIER OTRA RAZÓN.
Si algún producto llegara a tener defectos de material y/o mano de obra durante el período de validez de la garantía, devuélvalo junto con el comprobante de compra
y flete previamente pagado, a cualquier Centro de Servicio Autorizado de Wagner. (La lista de Centros de Servicio viene adjunta con este producto.) El Centro de
Servicio Autorizado de Wagner reparará o reemplazará el producto (según la opción de Wagner) y se lo devolverá, con porte previamente pagado.
ALGUNOS ESTADOS NO PERMITEN LIMITACIONES EN CUANTO A LA DURACIÓN DE UNA GARANTÍA IMPLÍCITA O LA EXCLUSIÓN DE DAÑOS
INCIDENTALES O DE CONSECUENCIA, DE MANERA QUE LA LIMITACIÓN Y EXCLUSIÓN ANTERIORES PODRÍAN NO SER VÁLIDAS PARA USTED.
ESTA GARANTÍA LE CONCEDE DERECHOS LEGALES ESPECÍFICOS, PERO USTED PODRÍA TENER DERECHO A OTROS, LOS CUALES VARÍAN DE UN
ESTADO A OTRO.
Wagner Spray Tech Corporation
Copyright © 2003 Wagner Spray Tech Corporation.
All rights reserved, including right of reproduction in
whole or in part, in any form. Printed in U.S.A.
1770 Fernbrook Lane
Minneapolis, Minnesota 55447
Telephone 1-800-880-0993
52
800-880-0993 © 2003 Wagner Spray Tech - All rights reserved.
English Français Español
Download from Www.Somanuals.com. All Manuals Search And Download.
|