Everyday Steam Mop
MODEL SF-140
User’s Guide
Please read all instructions before use.
KEEP YOUR RECEIPT FOR WARRANTY PURPOSES.
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Do not use unit where aerosol-based products are being used, or where oxygen is being
administered.
11. Unit is only meant to be used with recommended Everyday Steam Mop (model SF-140)
accessories. Using other types of attachments may cause damage to unit or injury.
12. If red Power Indicator Light does not illuminate when unit is plugged in and On/Off Switch is
pressed, unit is not operating normally. Immediately disconnect cord from power supply, then
refer to troubleshooting guide on Page 12 of this manual for assistance.
13. Always turn unit off and unplug power cord before filling Boiler with water. Do not attempt to
use unit without properly filling Boiler.
14. When filling Boiler, only water should be used in unit – other cleaning agents could damage
unit or cause injury. Distilled or de-mineralized water is highly recommended, in order to
minimize potential build-up of mineral deposits. Do not overfill unit.
15. To reduce risk of contact with hot water emitting from Steam Nozzles, check appliance before
each use by positioning it away from body and turning it on. Do not operate unit if Steam
Nozzles are blocked.
16. Burns can occur from touching hot metal parts, hot water, or steam. Do not touch bottom of
Mop Head or attempt to attach a Microfiber Pad by hand while unit is in use. Use caution
when you turn unit upside-down – there may be hot water in Boiler.
17. Use caution when using unit on uneven surfaces, such as stairs.
18. When steaming any surface for the first time, it is recommended that you consult the
manufacturer’s guidelines for material being steamed. For items in question, test on an
inconspicuous area before proceeding.
19. Steaming unsealed hardwood or unglazed ceramic surfaces is not recommended, and may
result in warping or damage to the surface. Steam may remove the sheen from surfaces
treated with wax.
20. When steam mopping, never leave unit resting in one spot on any surface for any period of
time – prolonged exposure to heat and moisture may damage floor surfaces.
21. Do not allow power cord to touch hot surfaces during use. Wrap cord loosely around Cord
Brackets when storing.
22. Always allow Everyday Steam Mop to cool (at least 30 minutes for complete cooling) and
empty Boiler before storing. Do not store unit with a damp Microfiber Pad still attached.
SAVE THESE INSTRUCTIONS!
FOR HOUSEHOLD USE ONLY
Questions or comments?
1-800-711-6617
•
•
•
Speak your mind! You are invited to review this product online:
|
ENGLISH
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
The following features and accessories are included with your Everyday Steam Mop. Carefully
inspect the packing material for all parts listed below. To obtain possible missing parts, refer to
Product Support on Pages 13 & 14 of this manual.
UNIT FEATURES & ACCESSORIES
1.
2.
2a.
3.
Handle
Telescopic Pole
Extension Lock
Cord Brackets
On/Off Switch
4.
5.
6.
7.
Power Indicator Light (red)
Heating Indicator Light (green)
Mop Head
8.
Boiler (internal)
Boiler Cap
Boiler Fill Hole
Pad Grips
8a.
8b.
9.
10.
11.
12.
13.
Steam Nozzles
Measuring Cup
Microfiber Pads (2)
Resting Pad
|
4
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
The Handle (1) connects to the top of the Telescopic Pole, and is designed for maximum grip
and comfort.
The Telescopic Pole (2) connects the Mop Head to the Handle, and can be extended and
retracted for comfortable use and convenient storage.
•
•
The Extension Lock (2a) is used to adjust the length of the Telescopic Pole.
The Cord Brackets (3) provide a convenient way to neatly wrap the power cord for storage.
The On/Off Switch (4), located on the back side of the Mop Head, is the foot-operated button
that activates and deactivates the unit. The On/Off Switch is pressed to turn the unit on (the
red Power Indicator Light will illuminate), then pressed again to turn the unit off (the red Power
Indicator Light will turn off).
•
•
•
The red Power Indicator Light (5) illuminates whenever the power cord is plugged into an
electrical outlet and the On/Off Switch is pressed, to indicate that unit is receiving power.
The green Heating Indicator Light (6) illuminates while the Boiler is actively heating water.
When the Boiler is empty, the Light will turn off.
The Mop Head (7) is the unit’s main body, housing the Boiler and producing steam through the
Steam Nozzles.
The Boiler (8) is the internal reservoir where water is held and converted into steam. For optimal
steam production, the Boiler should be filled with no more than 10 oz. (300 ml.) of water.
The Boiler Cap (8a) is designed to safely contain steam inside the Boiler, while providing easy
access to the Boiler Fill Hole. The Boiler Cap must be unscrewed and removed in order to fill
the Boiler with water.
•
•
•
•
•
The Boiler Fill Hole (8b) is the opening through which water is poured into the Boiler. The Boiler
Cap must be removed in order to access the Boiler Fill Hole.
The Pad Grips (9), located on the bottom of the Mop Head, are designed to adhere to fastener
strips on the Microfiber Pads.
The Steam Nozzles (10), located on the bottom of the Mop Head, evenly disperse the flow of
steam produced by the Boiler.
The Measuring Cup (11) provides an easy and convenient way to consistently fill the Boiler with
the optimum amount of water (10 oz. / 300 ml.).
•
•
•
•
•
The Microfiber Pads (12) each attach to the Pad Grips on the bottom of the Mop Head. The
Pads are designed to clean scuffs and stains from hard floors. The Microfiber Pads are reusable
and machine washable. Two Microfiber Pads are included.
The Resting Pad (13) serves as a base for the unit, providing a convenient place for it to rest as
the Boiler heats and cools without risk of damage to delicate floor surfaces. The Resting Pad
has a smooth side and a textured side – the textured side is designed to capture excess
moisture and should face upward, so that Mop Head rests on top of it.
•
|
ENGLISH
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling Your
Everyday Steam Mop
TELESCOPIC POLE
1. Connect Handle to upper (thicker) end of Telescopic Pole. To do this, simply slide Handle onto
pole until it snaps in place (FIGURE 1-A).
NOTE: Once connected, the Handle is not designed to be removed from the Telescopic Pole.
If it becomes necessary to remove it, contact Consumer Service for assistance (Page 13).
2. Insert lower (thinner) end of Telescopic Pole into yoke on top of Mop Head. When inserting, make
sure release button located on pole faces towards back side of yoke as illustrated (FIGURE 1-B).
3. Press Telescopic Pole into yoke until release button snaps through small hole on back side of
yoke (FIGURE 1-C). Telescopic Pole should now be secured to Mop Head.
NOTE: In order to coax the release button through the hole, it may be necessary to
rotate and adjust the Telescopic Pole until button aligns properly with hole.
4. To adjust length of Telescopic Pole, press Extension Lock downward. While holding lock down,
move the upper section of pole until it is at the desired length (FIGURE 1-D). Release lock,
then adjust upper section of pole again until it “clicks” securely into place.
5. To disconnect Telescopic Pole, swivel lower Cord Bracket 180º upward, then press firmly on
release button while simultaneously pulling pole away from Mop Head yoke (FIGURE 1-E).
1-A
1-B
1-C
1-D
1-E
FIGURE 1
|
6
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
MICROFIBER PADS
1. Lay one Microfiber Pad on flat surface, with fastener strips facing upward.
2. Align Mop Head above Microfiber Pad. Make sure Mop Head is oriented with pad as shown,
and centered as best as possible (FIGURE 2-A).
3. Press Mop Head firmly down onto Microfiber Pad. Fastener strips will adhere to Pad Grips on
underside of Mop Head. Pad should now be attached and ready for use (FIGURE 2-B).
4. To remove, use your foot to press down on Microfiber Pad release tab while simultaneously
pulling Mop Head up off of pad.
CAUTION: Use care when handling a recently used Microfiber Pad, as it may still be hot.
NOTE: Microfiber Pads are machine washable. To avoid picking up lint, washing
separately from other fabrics is recommended. Only use liquid detergent. Avoid using
any fabric softeners or bleach. Air drying is recommended; machine drying on a low
setting is acceptable as well.
2-A
2-B
FIGURE 2
|
ENGLISH
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your
Everyday Steam Mop
ADDING WATER
3-A
1. Make sure On/Off Switch is set to “off” position
(red Power Indicator Light will not be illuminated)
and power cord is unplugged.
2. Carefully remove Boiler Cap by unscrewing it in a
counter-clockwise direction (FIGURE 3-A).
3. If Boiler was not emptied completely after last use,
empty all remaining water now to prevent overfilling.
4. Fill included Measuring Cup with 8.5 oz. (250 ml.)
water, and pour into Boiler through Boiler Fill Hole
(FIGURE 3-B).
NOTE: In order to minimize potential mineral
build-up and prolong the life of your Everyday
Steam Mop, it is recommended that distilled or
de-mineralized water be used in the Boiler.
If distilled water is not available, then Boiler
should be cleaned frequently in order to
remove mineral build-up. Refer to Mineral
Build-Up section on Page 11 for details.
3-B
5. For maximum usable water (10 oz. / 300 ml.), fill
Measuring Cup with another 1.5 oz. (50 ml.) of
water, and add into Boiler.
6. Replace Boiler Cap by screwing it into Boiler Fill
Hole in a clockwise direction until tight (FIGURE
3-C). Unit is now ready to begin steaming – refer
to Page 9 for operating instructions.
REFILLING
If unit has been in use, always take
the following safety precaution before
removing the Boiler cap and adding water:
3-C
Allow unit to cool for 5-10 minutes. This will reduce
•
heat and pressure inside the Boiler, helping to
prevent escaping steam when the Boiler Cap is
removed as well as vaporization when more water
is added.
Once this is done, follow Adding Water procedure
above as usual.
WARNING: Failure to follow this precaution may
result in burns from escaping steam when the
Boiler cap is removed or when water is poured
into the Boiler.
FIGURE 3
|
8
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
STEAM MOPPING
Before operating, make sure Microfiber Pad is properly attached (Page 7) and Boiler is
filled with water (Page 8).
1. For first-time use, remove protective plastic cover that is shipped on electrical plug. Plug
power cord into a convenient electrical outlet.
2. Place Resting Pad on floor, so that textured side faces upward. Rest Mop Head on top of pad,
in order to help protect floor surface from excess heat and moisture during heat-up period.
3. Using your foot, gently press down on On/Off Switch until it clicks. Red Power Indicator Light
will illuminate to show that unit is receiving power. At the same time, green Heating Indicator
Light will illuminate to show that Boiler is heating.
4. After approximately 3 minutes of heating time, unit will begin emitting steam.
5. Remove unit from Resting Pad, and begin mopping.
Refer to Page 10 for a listing of floor surfaces that are recommended for cleaning with
your Everyday Steam Mop.
6. For best results, mop using a steady back-and-forth motion over the floor, working your way
backwards in order to avoid walking over the freshly mopped area.
IMPORTANT: To avoid warping or damage caused by heat and moisture, do not use on
unsealed hardwood or unglazed ceramic surfaces. Steam may remove the sheen from
some floors that have been treated with wax.
Never allow Everyday Steam Mop to rest idle on floor surfaces while still on – prolonged
exposure to steam in a single area may discolor or damage some floors. If it becomes
necessary to stop mopping at any time, always turn unit off and place back on Resting Pad.
7. Once all water has been used, green Heating Indicator Light will turn off to show that Boiler is
empty. If you wish to continue mopping, first turn unit off by pressing down gently on On/Off
Switch until it clicks, then unplug power cord from outlet. Refer to Refilling procedure on
Page 8 to refill Boiler.
8. The Microfiber Pad will absorb dirt and moisture during mopping. However, when you are
finished you may find some residual moisture has been left behind. In this case, it is
recommended to allow floor time to air-dry. A fan may be directed towards mopped area to
facilitate drying.
9. Once your mopping tasks are completed, place unit back on Resting Pad and turn it off by
pressing down gently on On/Off Switch until it clicks. Unplug power cord from outlet, then refer
to procedures on Page 11 for proper storage and care of your Everyday Steam Mop.
|
ENGLISH
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your
Everyday Steam Mop
RECOMMENDED FLOOR SURFACES
Below is a listing of some of the most common floor surfaces that the Everyday Steam Mop is
ideal for cleaning. If you have a question about a floor surface that isn’t listed below, please
contact our Consumer Service Department:
The Everyday Steam Mop is perfect for these floor surfaces:
Sealed Hardwood
•
Stained Concrete
•
Sealed Laminate
•
Linoleum
•
Ceramic
•
Granite
•
Marble
•
Slate
•
Vinyl
•
IMPORTANT: Do not use on unsealed hardwood or unglazed ceramic surfaces. Surfaces
that are not properly sealed may be warped or damaged by exposure to heat and moisture.
Care should also be taken when steaming sealed hardwood floors, as prolonged exposure
to steam in a single spot may cause damage and discoloration. To avoid this, keep the
Everyday Steam Mop in constant motion on these surfaces, and place it back on Resting
Pad when idle.
Steam may remove the sheen from some floors that have been treated with wax.
Extremely rough textured floors may tear or damage Microfiber Pads.
|
10 ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage & Care
PROPER STORAGE
Preparing your Everyday Steam Mop for storage is quick and simple. When you have finished
your mopping tasks, follow the steps listed below.
1. Gently press down on On/Off Switch until it clicks – red Power Indicator Light will turn off.
Unplug power cord from electrical outlet.
2. Place Mop Head on top of Resting Pad, and allow unit to cool (at least 30 minutes for complete
cooling).
3. For convenience it is recommended to disconnect Telescopic Pole, and if attached, remove
Microfiber Pad from Mop Head. If pad is dirty you may wash it, either by hand or in a washing
machine. Allow to air-dry.
4. Unscrew and remove Boiler Cap. Drain any water remaining in Boiler into a sink or tub, to
minimize potential mineral build-up and prevent overfilling during next use. Replace Boiler Cap
(do not fully tighten).
5. Reconnect Telescopic Pole. If desired, collapse Telescopic Pole to its shortest length (ideal for
limited storage space). Refer to Page 6 for details.
6. Wrap power cord around Cord Brackets.
7. Store Everyday Steam Mop in a cool, dry location, along with all included accessories.
MINERAL BUILD-UP
A common maintenance need for steam appliances is the removal of build-up caused by high
mineral content in many municipal water supplies. This mineral build-up may limit the
effectiveness and reduce the life of your Everyday Steam Mop.
The best way to minimize mineral build-up is to use distilled or de-mineralized water when
using your Everyday Steam Mop. In addition, it is recommended that the Boiler be cleaned at
least once a month in order to remove any deposits that form. This will help to extend the life of
your Everyday Steam Mop and keep it functioning at its maximum potential.
To remove mineral build-up:
1. Gently press down on On/Off Switch until it clicks – red Power Indicator Light will turn off.
Unplug power cord from electrical outlet.
IMPORTANT: Unit should remain off and unplugged during cleaning procedure.
2. Place Mop Head on top of Resting Pad, and allow unit to cool (at least 30 minutes for complete
cooling).
3. For convenience it is recommended to disconnect Telescopic Pole, and if attached, remove
Microfiber Pad from Mop Head. Leaving them off during cleaning will make the process easier.
4. Remove Boiler Cap and drain any water remaining in Boiler into a sink or tub.
5. Fill Measuring Cup with vinegar.
6. Pour vinegar into Boiler throught Boiler Fill Hole.
7. Allow vinegar to soak in boiler for 30-40 minutes.
8. Drain vinegar from Boiler into a sink or tub. Refill Boiler with fresh water, drain and repeat until
vinegar odor dissipates.
9. Replace Boiler Cap (do not fully tighten), reconnect Telescopic Pole and store your Everyday
Steam Mop as usual.
|
ENGLISH 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
PROBLEM
POSSIBLE CAUSE
Unit is not plugged in.
SOLUTION
Unit fails to heat up. Red Power
Indicator Light DOES NOT
illuminate.
Plug power cord into electrical outlet.
Press On/Off Switch until it clicks.
Reset circuit breaker / ground fault
Unit’s main power is not on.
Household circuit breaker / ground
fault interrupter has tripped or blown interrupter, or replace fuse. For
a fuse.
assistance, contact a licensed electrician.
Unit is damaged or otherwise in
need of repair.
Immediately cease usage and unplug.
Contact Consumer Service for
assistance (see Page 13 for details).
Unit fails to heat up. Red Power
Indicator Light DOES illuminate;
green Heating Indicator Light DOES
NOT illuminate.
No water in Boiler.
Refer to Adding Water procedure
on Page 8 to fill Boiler.
Unit heats up, but fails to steam. Both
red Power Indicator Light and
green Heating Indicator Light DO
illuminate.
Mineral build-up in unit.
Refer to Mineral Build-up section on
Page 11 for cleaning procedure.
Unit is damaged or otherwise in
need of repair.
Immediately cease usage and unplug.
Contact Consumer Service for
NOTE: Always allow sufficient
time for unit to heat up and begin
producing steam.
assistance (see Page 13 for details).
Steam output is weak or intermittent. Water level in Boiler is running low.
Refer to Refilling procedure on
Page 8 to refill Boiler.
Mineral build-up in unit.
Refer to Mineral Build-up section on
Page 11 for cleaning procedure.
Excessive moisture left on floor
during mopping.
Microfiber Pad has become
saturated with moisture.
Remove pad and replace with a
fresh dry one. To purchase
additional Pads, contact Consumer
Service (see Page 14 for details).
NOTE: It is normal for some
amount of moisture to be left
behind. Allow floor some time to
air-dry once mopping is complete.
Boiler has been overfilled.
Filling Boiler with more than 10 oz.
(300 ml.) of water interferes with
steam production, resulting in water
condensation in steam.
Drain some water out of Boiler.
Always use included Measuring Cup
to fill Boiler with correct amount of
water (see Page 8 for details).
Floor surfaces appear cloudy or
streaky after steaming.
Microfiber Pad is dirty / oversaturated. Replace pad with a clean dry one.
Hard water residue on floor. Switch to distilled water.
|
12 ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Support
CONSUMER SERVICES
For problems with your Steam Mop, please refer to the troubleshooting guide located on Page 12
of this manual. Additional inquiries should be directed to our consumer support services through
If you do not have internet access, you may also contact our Consumer Service Department by
telephone, at 1-800-711-6617.
NOTE: In order for our Consumer Service representatives to help you as quickly and
efficiently as possible, please have the following information ready before calling:
• Purchase information (where and when you purchased this product)
• Copy of purchase receipt / proof of purchase
• Product serial number (located near electrical specification label on back of unit)
• Date code (4-digit number located on electrical specification label on back of unit)
For information regarding your 1 year limited warranty, refer to Page 15 of this manual.
PRODUCT SPECIFICATIONS
SF-140
MODEL
VOLTAGE
120V
1000W
WATTAGE
8.3A
AMPERAGE
10 OZ. (300 ML.)
WATER CAPACITY
HEATING TIME
3 MIN. (APPROXIMATE)
12 MIN. (APPROXIMATE)
3.72 LBS. (1.69 KG.)
CONTINUOUS STEAM TIME
UNIT WEIGHT
11.5” (29.2 CM.) x 7.1” (18.0 CM.) x 47.1” (119.5 CM.)
18.7’ (570.0 CM.)
UNIT DIMENSIONS
POWER CORD LENGTH
|
ENGLISH 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Support
ACCESSORIES & PARTS
When ordering accessories and parts for your Everyday Steam Mop, you may refer to the part
numbers below. Replacement parts may be ordered through our Web site:
You may also contact Consumer Service directly:
MICROFIBER PADS (2)
RESTING PAD
A140-000R-
A142-003R-
CLEANFAST HARD FLOOR
SOLUTION (32oz)
(OPTIONAL – SOLD SEPARATELY)
CF-014R-
MEASURING CUP
A142-P002R-
CleanFast is a specially formulated,
non-toxic and biodegradable solution
that is designed to enhance steam
cleaning to eliminate the toughest
scuffs and stains. When used on
most any hard floor surface during
steam mopping, overall cleaning
effectiveness is increased beyond
what either steam or the Solution is
capable of alone.
CARPET GLIDER (WHITE ONLY)
(OPTIONAL – SOLD SEPARATELY)
A142-P003R-
NOTE: Due to continuing improvements, part numbers listed above may change.
For assistance ordering parts, please contact Consumer Service directly.
|
14 ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty Information
1 YEAR LIMITED WARRANTY
Steamfast, a division of Vornado Air LLC, (“Steamfast”) warrants to the original consumer or purchaser
this Steamfast Everyday Steam Mop SF-140 (“Product”) is free from defects in material or workmanship for
a period of one (1) year from the date of purchase. If any such defect is discovered within the warranty
period, Vornado, at its discretion, will repair or replace the Product at no cost if the Product is returned
to Steamfast postage-paid. Repairs not covered by the warranty or outside the warranty period will
require a fee to cover the cost of materials, handling and shipping.
This warranty does not apply to defects resulting from abuse of the Product, modification, alteration,
repair or service of the Product by anyone other than Steamfast, mishandling, improper maintenance,
commercial use of the Product, damages which occur in shipment or are attributed to acts of God.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE
REMEDY OF THE CONSUMER. STEAMFAST SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS
PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BYAPPLICABLE LAW, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS
LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow
limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may have other rights that vary from state to state.
For warranty or repair service, call 1-800-711-6617 or email [email protected] to obtain
a Return Authorization (“RA”) form. Please have or include your Product’s model number, date code and
serial number, as well as your name, address, city, state, zip code and phone number when contacting
Steamfast for warranty service. You may be required to provide the original sales receipt. For your
records: Staple or attach your original sales receipt to this Owner’s Guide. Please also write your
Product’s serial number below (located on product specs decal).
Serial No. __________________________________________________________________________
After receiving the RA form, ship your Product to:
Steamfast
Attn: Warranty & Repair
415 East 13th
Andover, KS 67002
To assure proper handling, packages must be clearly marked with the RA number. Packages not
clearly marked with the RA number may be refused at the receiving dock.
Please allow 1-2 weeks for repair and return of your Product after the Product is received.
© 2011 Vornado Air LLC • Andover, KS 67002
Specifications subject to change without notice.
Steamfast® is a trademark owned by Vornado Air LLC.
Manufactured in China.
Steamfast Consumer Service
|
P: 1-800-711-6617
|
|
ENGLISH 15
Download from Www.Somanuals.com. All Manuals Search And Download.
review this product online
evalúe este producto en línea
évaluer ce produit en ligne
Steamfast
415 East 13th, Andover, KS 67002
V110512
Download from Www.Somanuals.com. All Manuals Search And Download.
|