DP-1200X
Digital Projector User Manual
English
030531
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in commercial installation.
This equipment generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, detectable by turning the equipment in question off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna
Increase the distance between the equipment and the receiver
Connect the equipment to an outlet on a different circuit than that which the receiver
is connected to
Or consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to following
two conditions:
1.This device may not cause harmful interference, and
2.This device must accept any interference that may cause undesired operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN-1
Projector
User’sManual
Precautions
Safety Instructions
1. Check that the operating voltage of your unit is identical with the voltage of your
local power supply.
2. Should any liquid or solid object fall into the cabinet, unplug the unit and have it
checked by the qualified personnel before operating it further.
3. Do not place the projector on an unstable stand or table.
4. Unplug the unit from the wall socket if it is not to be used for several days.
To disconnect the cord, pull it out by the plug. Never pull the cord itself.
5. The wall socket should be near the unit and easily accessible.
6. Do not place the projector where the cord can be stepped on as this may result in
fraying or damage to the lead or the plug. Be alert to tripping hazards.
7. Never look into the projector lens when the lamp is switched on as the bright light
can damage your eyes. Never let children look into the lens when it is on.
8. Do not place your hand or objects near the ventilation holes. The air coming out is
hot.
9. Never open any covers on the projector except the lamp cover. Dangerous
electrical voltages inside the projector can cause severe injury. Except as
specifically directed in this Instruction Manual, do not attempt to service this product
yourself. Refer all servicing to qualified service personnel.
10. Unplug the projector from the wall socket before cleaning. Use a damp cloth for
cleaning the projector housing. Do not use liquid or aerosol cleaners.
11. Keep the plastic packing materials (from the projector, accessories and optional
parts) out of the reach of children as these bags may result in death by suffocation.
Be particularly careful around the small children.
EN-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Cautions
The projector is equipped with ventilation holes (intake) and ventilation holes
(exhaust). Do not block or place anything near these slots, or internal heat build-up
may occur, causing picture degradation or damage to the projector.
When you replace the projector lamp, never touch the new bulb with your bare
hands. The invisible residue left by the oil on your hands may be shorten the bulb
life. Use lint-free gloves or finger cots are recommended.
Preventing Internal Heat Build-Up
After you turn off the power with the Power button, do not disconnect the unit from the
wall outlet while the cooling fan is still running.
Repacking
Save the original shipping carton and packing material; they will come in handy if you
ever to ship your unit. For maximum protection, repack your unit as it was originally
packed at the factory.
EN-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
CONTENTS
Projector Features and Controls
6
6
7
8
8
Projector
Control Panel
Remote Controller
Button Function
Getting the Most Out of Your Projector
9
9
9
9
Remote Controller
Auto Off Mode
Control Panel
Setup
10
10
11
12
13
14
14
14
15
16
Unpacking the Projector
Setting Up the Projector
Connecting to a Computer
Connecting to a Video Source
Using the Projector
Turning the Audio/Visual(A/V) Equipment On and Off
Turning the Projector On and Off
Focusing and Positioning the Screen Image
Operational Indicator(LED)
Projector Control Menus
16
16
18
19
19
21
22
Changing a Menu Setting
Menu Options
Input Menu
Picture Menu
Color Menu
PIP Menu
EN-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
24
24
25
27
27
28
28
28
29
30
31
Audio Menu
MISC Menu
Option Menu
Language Menu
Reset Menu
Other Related OSD Menus
Video Input Signal
Picture Menu
Video Menu
Other OSD Menus
No Input Signal
Maintenance
32
32
32
33
34
Cleaning the Lens
Cleaning the Projector Housing
Cleaning the Air Filter
Replacing the Lamp
Technical Specifications
Appendix A
35
36
36
37
Preset Signals
HDTV Preset Signals
EN-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
PROJECTOR FEATURES AND CONTROLS
PROJECTOR
9
10
1.Zoom ring
2.Focus ring
8
3.Lens
4.Ventilation holes (intake)
5.Ventilation holes (exhaust)
6.Adjuster button
7.Height adjustment
8.Front IR remote controller sensor
9.Speakers
13
10.Control Panel including
Power button
2
1
3
11.AC power socket
12.Rear IR remote controller sensor
13.Security lock receptacle
14.Control port (PS2 & USB)
15.Computer IN (DVI-I) connector
16.Monitor OUT
11
5
19
14
6
18
17
17.S-video input
18.Y connector
19.Cb connector
20.Cr connector
21.Audio input jacks (L & R)
22.Composite Video input jack
23.Lamp cover
6
4
24.Air filter
12
21
16
15
20
22
23
24
7
EN-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
CONTROL PANEL
LED
POWER
LAMP
Power LED indicator – indicates power to projector.
Lamp LED indicator – indicates lamp power.
Button Function
Turns the projector and lamp ON and OFF.
Manually selects an input source.
INPUT
AUTO
Automatically adjusts frequency and phase.
Displays (or hides) the on-screen control menus.
Increases the volume of the projector’s speakers.
Decreases the volume of the projector’s speakers.
It can be used as a navigation controller to navigate
MENU
VOLUME(+)
VOLUME(-)
Cursor Controller
(ꢀ/ꢁ/ꢂ/ꢃ)
the projector menus.
ꢀ-Scrolls up through the menu choices.
ꢁ-Scrolls down through the menu choices.
ꢃ-Increases the value setting on the selected sub-menus,
or confirms a menu selection.
ꢂ-Decreases the value setting on the selected sub- menus.
EN-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
REMOTECONTROLLER
Button Function
POWER
INPUT
AUTO
MENU
ꢀ
Turns the projector and lamp ON and OFF.
Manually selects an input source.
Automatically adjusts frequency and phase.
Displays (or hides) the on-screen display menus.
Scrolls up through the menu choices.
Scrolls down through the menu choices.
Increases the value setting on the selected sub-menus, or
confirms a menu selection.
ꢁ
ꢃ
ꢂ
Decreases the value setting on the selected sub-menus.
Functions as left mouse(only functions when your projector is
equipped with an optional mouse link cable).
Functions as right mouse(only functions when your projector is
equipped with an optional mouse link cable).
Fires laser pointer (press and hold).
Adjusts the volume of the projector’s
speakers.
LASER
VOLUME(+ ,-)
KEYSTONE
ZOOM(+,-)
Selects vertical or horizontal trapezoidal
distortion.
Digitally zooms the current image
window.
MUTE
Cuts off the sound temporarily.
FREEZE
Freezes the current graphics and video
image on the screen.
BLANK
Cuts off the screen temporarily.
Note:
During the on-screen display(OSD) menu is inactive, the
ꢀ,ꢁ‚ꢃ,ꢂ, and buttons will function as a remote
mouse for your PC (only if your projector is equipped with an
optional mouse link cable).
Toggle the KEYSTONE button to select the desired trapezoidal distortion. To
adjust the trapezoidal distortion of the projection, press the ꢂor ꢃbutton.
EN-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
GETTING THE MOST OUT OF YOUR PROJECTOR
The projector has a full set of features that allow you to control the settings for video,
audio, power management, display parameters, and much more.
To derive the greatest utility from your projector, read this section for a quick summary
of the important features.
Remote Controller
The buttons on the Remote Controller allow direct and immediate control of the most
commonly used features including source selection, keystone adjustment, volume
control, image freeze-frame, zoom, screen blanking, audio muting and power control.
Remote Controller buttons can also be used for advanced functions and to access the
projector’s menu system. The remote controller can even be used as a remote mouse
for your computer, and also includes a laser pointer.
Auto Off Mode
The auto off mode conserves electricity by automatically turning off the lamp if the
projector does not receive input signal for a specified period (30 minutes). In the auto
off mode, the lamp is turned off, conserving electricity, cooling the projector and
extending the life of the lamp. Use the Power button on either the Remote Controller or
the Projector Control Panel to turn the projector on again if it has powered off.
Control Panel
The control panel buttons on the top of projector offer access to advanced functions,
such as adjusting the brightness and contrast for computer images.
EN-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
SETUP
This section tells you how to unpack and set up your projector and connect it to other
equipment. The projector must be connected to a computer or a video source such as
a video tape deck, camcorder, digital camera or laser disk player in order to make a
projection.
You may want to connect the projector to both your computer and a video source, or
set up the projector for one or more of the following:
Connect the mouse cable to use the remote controller as a wireless mouse.
Provide audio source. The audio source can be the computer, video source, or
another device such as a stereo.
Unpacking the Projector
When you unpack the projector, make sure you have all these components:
Projector
Projector carrying case
Remote Controller (IR)
2 AAA batteries for the Controller
Power cord
Computer cable (D-SUB to DVI cable)
S Video cable
A/V composite cable (RCA type for composite video & audio)
Lens cap
Instruction manual
The following cables are optional accessories:
Audio cable
HDTV to DVI (When using HDTV as input signal)
Mouse cable (for PS/2)
Mouse cable (for USB)
DVI cable
Component Video cable
Monitor OUT cable (D-SUB cable)
Many of the above optional items may not be required for your particular installation.
Retain packaging materials in case you need to move or ship the projector in the
future. It should always be transported in its original protective packaging.
EN-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Setting Up the Projector
1.Place the projector on a sturdy, level surface within five feet of the computer or video
source.
Caution:
Do not hold the projector by the lens. This can damage the lens.
2.Place the projector the correct distance from the screen. The distance between the
projector and the screen determines the actual image size. Use the general
guidelines below to determine the correct distance.
Distance between the
screen and the center of the lens
Projector
Distance
1 Meter 2 Meters 2.5 Meters 4 Meters 5 Meters 8 Meters 10 Meters
Projection
Size(Diagonal)
WIDE
TELE
34.3”
25.9”
68.8”
51.8”
83.8”
63.5”
137.2”
103.6”
167.6”
125.6”
274.4”
207.2”
331.4”
251.2”
3.When replacing batteries on the Remote Controller, take the following precautions:
Do not recharge batteries or expose batteries to fire or water.
Replace batteries as soon as they run down. If the batteries leak, wipe away the
fluid with a soft cloth. If battery fluid gets on your hands, wash them immediately.
Remove the batteries if you will not be using the remote controller for a long
period of time.
EN-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Connecting to a Computer
Projector
IN
Computer
OUT
Computer Cable
DVI or VGA OUT
The projector will always project at XGA (1024 x 768) resolution. (XGA is the native
resolution of the projector.) However, you can connect the projector to a computer
source capable of displaying VGA (640 x 480), SVGA (800 x 600), XGA or SXGA
(1280 x 1024) resolutions. The projector will resize VGA, SVGA, and SXGA inputs for
XGA projection. The types of computers supported by this projector include IBM,
Macintosh and Apple compatible laptop or desktop PCs (PC compatibles).
Note:
If the input source is Computer, it can produce MONITOR OUT function.
EN-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Connecting to a Video Source
Y Cb Cr (Component Video Cable)
S-Video Cable OUT
IN
OUT
IN
DVD Player
Y
R/W
OUT
AV Composite Cable
Video out VCR
You can connect the projector to almost any common video source - VHS player, DVD
player, camcorder, laser disc player or any other compatible video image source.
The projector can accept composite, component, or S-Video signals:
Composite video is characterized by a single-pin “RCA-type” video jack, usually
colored yellow.
Component video (YCbCr) is less common and features three “RCA-type” video
jacks, typically colored green, blue and red.
S-Video is readily identified by a single connector with four small pins.
You can connect the projector simultaneously to composite, component, and S-
Video sources. You can select which video source to project using the control panel
or remote controller. If the Auto Search feature is ON (see later sections of this
manual), the projector will automatically detect and select a source. The projector
supports NTSC, PAL and SECAM video formats. The projector will automatically
detect and identify the video format. Note, however, whereas the projector can accept
multiple simultaneous sources it can only accept one video format at a time.
Note:
The projector is not compatible with a cable TV-style coaxial “F” connector.
EN-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Using the Projector
This section describes projector operations:
Turning the projector and A/V equipment on and off
Adjusting the projected image
Projector controls
Checking the projector status
Turning the Audio/Visual (A/V) Equipment On and
Off
Always turn on the projector and related A/V equipment in the following order.
1.Projector
2.Computer
3.Video source
4.Audio source
Turning the Projector On and Off
1.Connect the power cord to the projector.
2.Insert the power plug into a wall outlet.
3.Remove the projector lens cap.
4.Press the Power button (on either the Remote Controller or the Projector Control
Panel) to turn on the projector. When the lamp LED indicator lights in green, the
projecting image gets full illumination.
Warning:
Never look into the lens when the lamp is on. This can damage your eyes.
It is especially important that children are not allowed to look into the lens.
5.To turn off the projector, press the Power button. A message will appear on the
screen for about 10 seconds:
6.Press the Power button once again(to turn off the power) while the message is still
showing on the screen.
Note:
Please wait until the fan motor turns off and the Power LED becomes red before
removing the power cord from the projector.
EN-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Focusing and Positioning the Screen Image
After an image appears on the screen, check to see if it is in focus and whether it fits
properly on the screen.
To adjust the focus of the image, rotate the focus ring, which is the right one on the
projector’s lens.
To adjust the size of the image, rotate the left zoom ring. Zooming out to make the
image larger or zooming in make it smaller on the screen.
Note:
Push the adjuster button to adjust the projected image position. Hold down the adjuster
button and pull the height adjustment. Release the adjuster button and the height
adjustment position will be locked.
EN-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Operational Indicator (LED)
There are two LEDs on the top of the projector, the Power LED and the Lamp LED.
They provide valuable information about the projector.
LED TYPE
Power LED
Power LED
COLOR
Green
Red
STATUS
Solid
MEANING
The projector is powered and ready.
The projector system has some problems with its fan, so
the projector cannot start up.
Solid
Lamp LED
Lamp LED
Green
Red
Solid
Solid
The lamp is in good condition and is projecting at
maximum brightness.
The lamp has reached its end of life and must be
changed soon. The lamp will continue to operate until
it fails. Change the lamp and reset the lamp time
counter.
Lamp LED
Amber
Flashing
The projector is shutting down. The fan motor is
cooling the lamp for shutdown. Do not unplug the
power cable or turn the power switch off before the
Lamp LED turns off. The fan motor will turn off when
the lamp has cooled.
PROJECTOR CONTROL MENUS
This section describes how to make various adjustments and settings using the menus.
Changing a Menu Setting
The projector menus can be accessed using either the Projector Control Panel or the
Remote Controller.
1.Changing the menu display:
Press the MENU button either on the Remote Controller or the Projector Control
Panel.
Each press of the MENU button switches the display format as follows:
EN-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
2.Selecting the desired menu or sub-menu(to scroll through the menu choices):
On the Projector Control Panel: press the ꢀor ꢁbutton.
On the Remote Controller: press the ꢀor ꢁbutton.
Note:
To scroll up: press the ꢀbutton.
To scroll down: press the ꢁbutton.
3. Adjusting the value setting:
On the Projector Control Panel: press the ꢂor ꢃbutton.
On the Remote Controller: press the ꢂor ꢃbutton.
Note:
To increase value: press the ꢃbutton.
To decrease value: press the ꢂbutton.
To confirm the selection on the INPUT, PICTURE (Auto Tracking), LANGUAGE
and RESET menus, press the ꢃbutton.
4.During the on-screen display(OSD) menu is inactive:
On the Remote Controller, the ꢀ,ꢁ‚ꢃ,ꢂ,
and
buttons will function
as a remote mouse for your PC (only if your projector is equipped with an optional
mouse link cable).
On the Projector Control Panel, each press of the ꢀor ꢁbutton switches the
display format (quick key menu) as follows:
Note:
To change the setting on the quick key menus, press the ꢂor ꢃbutton on the Projector
Control Panel.
EN-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Menu Options
The projector is equipped with three types of on-screen display(OSD) menus.
Each OSD menu interface you will see on the screen is depending on the type of input
signal.
Input Signal Type
Menu Interface
Computer
DVI
HDTV
Input, Picture, Color, PIP, Audio, Misc, Option, Language, Reset
S-Video
Video
YCbCr
Input, Picture, Color, Video, Audio, Misc, Option, Language,
Reset
None
Input, Option, Language, Reset
EN-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Input Menu
This menu allows to specify the signal source that you wish to project. This is particularly
useful if you have several sources (video and/or computer) connected to your projector.
Changing settings procedure (using either the Projector Control Panel or the Remote
Controller):
1.Press the MENU button to display OSD
menu.
2.Press the ꢀor ꢁbutton to select
INPUT menu.
3.To enter the sub-menu setting, press
the MENU button once again.
4.Press the ꢀor ꢁbutton to select the
desired input source.
5.Press the ꢃbutton to confirm the input selection.
6.To exit from the current menu, toggle the MENU button.
The following table provides detail of the available sub-menu choices:
Option
Computer
DVI
Description
Signal from computer. (desktop or notebook)
Signal from DVI(Digital Visual Interface) device.
Component video signal.
YCbCr
S-Video
Video
S-video signal.
Composite video signal.
HDTV
Signal from HDTV.
(High Definition TV - a high-resolution TV
standard, which is part of the group of digital
TV standards introduced in USA in late 1998).
Automatically scans the input source.
Auto Search
Picture Menu
This menu provides precise control of the projected image including:
brightness, contrast, position(vertical & horizontal), tracking, sync, sharpness(computer
signal) and auto tracking.
EN-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Changing settings procedure (using either the Projector Control Panel or the Remote
Controller):
1.Press the MENU button to display OSD
menu.
2.Press the ꢀor ꢁbutton to select
PICTURE menu.
3.To enter the sub-menu setting, press the
MENU button once again.
4.Press the ꢀor ꢁbutton to select the
sub-menu item.
5.Press the ꢂor ꢃbutton to adjust the value of desired sub-menu item.
On the Auto Tracking sub-menu, press the ꢃbutton to confirm the selection.
6.After you have done with the adjustment of a sub-menu item:
a.To resume changing another sub-menu item: press the ꢀor ꢁbutton.
b.To exit from the current menu: toggle the MENU button.
The following table provides detail of the available sub-menu choices:
Sub-Menu
Description
Brightness
The higher the setting, the brighter the image.
The lower the setting, the darker the image.
The higher the setting, the greater the contrast.
The lower the setting, the lower the contrast.
Adjusts the horizontal position.
Contrast
PosiH
PosiV
Tracking
Sync
Adjusts the vertical position.
Adjusts the horizontal pixel of the image.
Adjusts the dot phase of the input signal.
Adjusts the picture to where it looks best.
The higher the setting, the sharper the image.
The lower the setting, the softer the image.
Automatically scans the projected image to fine tune.
Sharpness
Auto Tracking
EN-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Color Menu
This menu provides precise control of the color settings including:
color temperature (preset & user define) and gamma.
Changing settings procedure (using either the Projector Control Panel or the Remote
Controller):
1.Press the MENU button to display OSD
menu.
2.Press the ꢀor ꢁbutton to select
COLOR menu.
3.To enter the sub-menu setting, press the
MENU button once again.
4.Press the ꢀor ꢁbutton to select the
sub-menu item.
5.Press the ꢂor ꢃbutton to adjust the value of desired sub-menu item.
On the Color Temp and Gamma sub-menus, press the ꢂor ꢃbutton to select
the desired setting.
6.After you have done with the adjustment of a sub-menu item:
a.To resume changing another sub-menu item: press the ꢀor ꢁbutton.
b.To exit from the current menu: toggle the MENU button.
The following table provides detail of the available sub-menu choices:
Sub-Menu
Option
Description
Color Temp
Adjusts the whiteness of the screen.
Gives the white colors a red tint.
Gives the white colors a neutral tint.
Gives the white colors a blue tint.
Manually adjusts color temperature.
Manually adjusts red.
L
M
H
U
User R
User G
User B
Gamma
Manually adjusts green.
Manually adjusts blue.
Selects a gamma correction curve.
Improves computer’s image mode.
Improves video’s image mode.
Gamma1
Gamma2
EN-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
PIP Menu
This menu enables you to adjust the PIP (additional video image window on the
graphics background) settings such its size, position (horizontal & vertical), brightness,
contrast, saturation, tint, sharpness and source selection.
Changing settings procedure (using either the Projector Control Panel or the Remote
Controller):
1.Press the MENU button to display OSD
menu.
2.Press the ꢀor ꢁbutton to select PIP
menu.
3.To enter the sub-menu setting, press
the MENU button once again.
4.Press the ꢀor ꢁbutton to select the
sub-menu item.
5.Press the ꢂor ꢃbutton to adjust the value of desired sub-menu item.
On the Size and Input sub-menus, press the ꢂor ꢃbutton to select the
desired setting.
6.After you have done with the adjustment of a sub-menu item:
a.To resume changing another sub-menu item: press the ꢀor ꢁbutton.
b.To exit from the current menu: toggle the MENU button.
EN-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
The following table provides detail of the available sub-menu choices:
Sub-Menu Option
Description
Size
Sets the PIP size.
Off
No additional image window on the screen.
Additional image window size sets to small.
Additional image window size sets to medium.
Additional image window size sets to large.
Adjusts the additional image window horizontal
position.
Small
Medium
Large
PosiH
PosiV
Adjusts the additional image window vertical
position.
Brightness
Contrast
Saturation
The higher the setting, the brighter the picture.
The lower the setting, the darker the picture.
The higher the setting, the greater the contrast.
The lower the setting, the lower of contrast.
The strength of a color especially the degree to
which it lacks its complimentary color.
The higher the setting, the stronger color strength.
The lower the setting, the weaker color strength.
Adjusts shade and variety of the picture between
red color and green color.
Tint
Sharpness
The higher the setting, the sharper the picture.
The lower the setting, the softer the picture.
Scans the PIP source.
Input
Auto
Automatically scans the input source.
PIP source from composite video signal.
PIP source from S-video signal.
Video
S-Video
EN-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Audio Menu
This menu allows you to control volume and mute(on/off) the audio.
Changing settings procedure (using either the Projector Control Panel or the Remote
Controller):
1.Press the MENU button to display OSD
menu.
2.Press the ꢀor ꢁbutton to select
AUDIO menu.
3.To enter the sub-menu setting, press
the MENU button once again.
4.Press the ꢀor ꢁbutton to select the
sub-menu item.
5.Press the ꢂor ꢃbutton to adjust the value of desired sub-menu item.
On the Mute sub-menu, press the ꢂor ꢃbutton to select the desired setting.
6.After you have done with the adjustment of a sub-menu item:
a.To resume changing another sub-menu item: press the ꢀor ꢁbutton.
b.To exit from the current menu: toggle the MENU button.
The following table provides detail of the available sub-menu choices:
Sub-Menu
Volume
Mute
Option
Description
Adjusts the volume.
Cuts off the sound temporarily.
Mute function is active.
Mute function is inactive.
On
Off
MISC Menu
This menu includes projector utilities for keystone(vertical & horizontal), freeze frame
(on/off), blank screen(on/off), and blank color mode settings.
Changing settings procedure (using either the Projector Control Panel or the Remote
Controller):
1.Press the MENU button to display OSD
menu.
2.Press the ꢀor ꢁbutton to select MISC
menu.
EN-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
3.To enter the sub-menu setting, press the MENU button once again.
4.Press the ꢀor ꢁbutton to select the sub-menu item.
5.Press the ꢂor ꢃbutton to adjust the value of desired sub-menu item.
On the Freeze, Blank and Blank Color sub-menus, press the ꢂor ꢃbutton to
select the desired setting.
6.After you have done with the adjustment of a sub-menu item:
a.To resume changing another sub-menu item: press the ꢀor ꢁbutton.
b.To exit from the current menu: toggle the MENU button.
The following table provides detail of the available sub-menu choices:
Sub-Menu
Option
Description
V-Keystone
Adjusts trapezoidal distortion (vertically) of the
picture that may occur depending the projection
angle.
H-Keystone
Freeze
Adjusts trapezoidal distortion (horizontally) of the
picture that may occur depending the projection
angle.
Freezes the screen.
On
Off
Freeze function is active.
Freeze function is inactive.
Blanks the screen temporarily.
Blank function is active.
Blank
On
Off
Blank function is inactive.
Blank Color
Selects the screen color when Blank is active.
Blanks to blue screen.
Blue
Black
Blanks to black screen.
Option Menu
This menu includes projector utilities for OSD timeout, OSD position (horizontal &
vertical), projection mode, auto off (On/Off) and lamp life.
Changing settings procedure (using either the Projector Control Panel or the
Remote Controller):
1.Press the MENU button to display OSD menu.
2.Press the ꢀor ꢁbutton to select OPTION menu.
3.To enter the sub-menu setting, press the MENU button once again.
EN-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
4.Press the ꢀor ꢁbutton to select the sub-menu item.
5.Press the ꢂor ꢃbutton to adjust the
value of desired sub-menu item.
On the Projection and Auto Off
sub-menus, press the ꢂor ꢃbutton
to select the desired setting.
On the Lamp Life sub-menu, the
lamp’s lifetime counter is calculated by
the projector system.
6.After you have done with the adjustment of a sub-menu item:
a.To resume changing another sub-menu item: press the ꢀor ꢁbutton.
b.To exit from the current menu: toggle the MENU button.
The following table provides detail of the available sub-menu choices:
Sub-Menu
OSD Timeout
OSD PosiH
Option
Description
Duration OSD menu stays active (at idle state).
Adjusts OSD menu display position
(horizontally - left & right) on the screen.
Adjusts OSD menu display position (vertically - up
& down) on the screen.
OSD PosiV
Projection
Sets the projection display.
Front
Rear
The image is projected directly on the screen.
The image is reversed horizontally.
The image is inverted vertically.
Automatically turns off the lamp if the projector does
not detect an input signal for specified time period
(30 minutes).
Ceiling
Auto Off
On
Off
Auto Off is active.
Auto Off is inactive.
Lamp Life
Displays lamp’s lifetime counter (by hour).
EN-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Language Menu
This menu enables you to select the language used in the OSD(on-screen display)
menus.
Changing settings procedure (using
either the Projector Control Panel or the
Remote Controller):
1.Press the MENU button to display
OSD menu.
2.Press the ꢀor ꢁbutton to select
LANGUAGE menu.
3.To enter the sub-menu setting, press the MENU button once again.
4.Press the ꢀor ꢁbutton to select the desired OSD language.
5.Press the ꢃbutton to confirm the OSD language selection.
6.To exit from the current menu, toggle the MENU button.
Note:
This projector supports multilanguage.
Reset Menu
This menu allows you to restore all projector settings and adjustments back to the
factory defaults.
Changing settings procedure (using either the Projector Control Panel or the Remote
Controller):
1.Press the MENU button to display
OSD menu.
2.Press the ꢀor ꢁbutton to select
RESET menu.
3.To enter the sub-menu setting, press
the MENU button once again.
4.Press the ꢀor ꢁto select YES if you
want to restore all projector settings to the factory defaults.
5.Press the ꢃbutton to confirm the selection.
6.To exit from the current menu, toggle the MENU button.
EN-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Other Related OSD Menus
Following are the descriptions on the on-screen display menus with video input sources
and without input source attached to your projector.
Video Input Signal
If the input signal comes from composite video(video), S-video or component video
(YCbCr), you may see different PICTURE menu and VIDEO menu interface.
Picture Menu
This menu provides precise control of the projected image including:
brightness, contrast, saturation, tint and sharpness(video signal).
Changing settings procedure (using either the Projector Control Panel or the Remote
Controller):
1.Press the MENU button to display OSD
menu.
2.Press the ꢀor ꢁbutton to select
PICTURE menu.
3.To enter the sub-menu setting, press
the MENU button once again.
4.Press the ꢀor ꢁbutton to select the
sub-menu item.
5.Press the ꢂor ꢃbutton to adjust the value of desired sub-menu item.
6.After you have done with the adjustment of a sub-menu item:
a.To resume changing another sub-menu item: press the ꢀor ꢁbutton.
b.To exit from the current menu: toggle the MENU button.
EN-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
The following table provides detail of the available sub-menu choices:
Sub-Menu
Description
Brightness
The higher the setting, the brighter the image.
The lower the setting, the darker the image.
The higher the setting, the greater the contrast.
The lower the setting, the lower the contrast.
The strength of a color especially the degree to which
it lacks its complimentary color.
Contrast
Saturation
The higher the setting, the stronger color strength.
The lower the setting, the weaker color strength.
Adjusts the projection between red and green color.
The higher the setting, the sharper the image.
The lower the setting, the softer the image.
Tint
Sharpness
Video Menu
This menu enables you to adjust the video settings such as its aspect ratio and video
format.
Changing settings procedure (using either the Projector Control Panel or the Remote
Controller):
1.Press the MENU button to display
OSD menu.
2.Press the ꢀor ꢁbutton to select
VIDEO menu.
3.To enter the sub-menu setting, press
the MENU button once again.
4.Press the ꢀor ꢁbutton to select the
sub-menu item.
5.Press the ꢀor ꢁbutton to select the desired setting.
6.After you have done with the adjustment of a sub-menu item:
a.To resume changing another sub-menu item: press the ꢀor ꢁbutton.
b.To exit from the current menu: toggle the MENU button.
EN-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
The following table provides detail of the available sub-menu choices:
Sub-Menu
Option
Description
Aspect Ratio
HDTV and video display selection.
Selects 16:9 aspect ratio.
Selects 4:3 aspect ratio.
Video format selection.
16:9
4:3
Source
Auto
Automatically scans video format.
Sets video format as NTSC.
Sets video format as PAL.
Sets video format as SECAM.
NTSC
PAL
SECAM
Other OSD Menus
Other OSD menus operation and description are the same as the previous page.
Input Menu: refer to page 19.
Color Menu: refer to page 21.
Audio Menu: refer to page 24.
MISC Menu: refer to page 24.
Option Menu: refer to page 25.
Language Menu: refer to page 27.
Reset Menu: refer to page 27.
EN-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
No Input Signal
If there is no input signal attached with your projector, if you press the MENU button
(on either the Projector Control Panel or the Remote Controller), one of the following
on-screen display menus will appear on the screen.
Input Menu
(refer to page 19)
Option Menu
(refer to page 25)
Language Menu
(refer to page 27)
Reset Menu
(refer to page 27)
EN-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
MAINTENANCE
The projector needs little maintenance. You should keep the lens clean as dust, dirt or
spots will project on the screen and diminish image quality.
You will also need to clean the air filter located at the bottom of the projector periodically.
It is important to keep the air filter clean because a clogged air filter prevents proper
ventilation which is necessary to cool the projector and prevent it from overheating.
The only part you should replace yourself are the lamp and the air filter.
If any other parts need replacing, contact your dealer or qualified service personnel.
When cleaning any part of the projector, always switch off and unplug the projector
first.
Warning:
Never open any of the covers on the projector except the lamp and air filter
covers. Dangerous electrical voltages inside the projector can cause severe
injury. Except as specifically indicated in this Instruction Manual, do not attempt
to service this product yourself. Refer all servicing to qualified service
personnel.
Cleaning the Lens
Clean the lens whenever you notice dirt or dust on the surface. Wipe the lens surface
gently with a soft, dry, lint-free cloth.
To remove dirt or stains on the lens, moisten a soft cloth with water and a neutral
detergent and gently wipe the lens surface.
Cleaning the Projector Housing
To clean the projector housing, first unplug the power cable. To remove dirt or dust,
wipe the housing with a soft, dry, lint-free cloth. To remove stubborn dirt or stains,
moisten a soft cloth with water and a neutral detergent. Then wipe the housing. Do not
use alcohol, benzene, thinners or other chemical detergents as these can cause
damage to the housing.
EN-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Cleaning the Air Filter
The air filter, which is located at the bottom of the projector, should be cleaned after
every 100 hours of use. If it is not cleaned periodically, it can become clogged with
dust and prevent the projector from being ventilated properly. This can cause
overheating and damage the projector.
To clean the air filter:
1.Switch the projector off and unplug the power cable from the wall socket.
2.Place a protective sheet (cloth) beneath the projector. Turn the projector over so you
can see its underside.
3.Remove the air filter by pulling the filter tab.
4.Clean the air filter.
Caution:
To clean the filter, you are advised to use a small vacuum cleaner designed
for computers and other office equipment.
If the dirt is difficult to remove or if the filter is torn, replace it.
5. Replace the filter.
6. Plug the power back into the projector.
Note:
Be sure that the projector is stable after turning it over.
EN-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Replacing the Lamp
The projector lamp used for the light source has a certain life. It is time to replace them
lamp when:
When lamp dims, the projected image gets darker or starts to deteriorate.
The projector lamp LED indicator turns to red (See page 16).
Caution:
The lamp becomes a high temperature after turning off the projector with the
power button. If you touch the lamp, you may scald your finger. When you
replace the lamp, wait for at least an hour for the lamp to cool. Be sure to turn off
the projector and unplug the power cord before replacing the lamp.
1.Turn off the projector and unplug the power cable.
2.Turn the projector over so you can access the lamp cover.
3. Remove the access panel screws and open the panel.
4. Remove the screws on the bottom of the lamp assembly.
5. Grasp the lamp handle and pull the lamp assembly directly out of the projector.
6. Replace with the new lamp.
7. Place back the screws on the bottom of lamp assembly.
8. Place the panel and screw back the screws on the lamp cover.
Note:
Be sure not to touch the optical surfaces with your fingers.
Lint-free gloves or finger cots are recommended.
Do not put your hands into the lamp replacement spot,
or not fall any liquid or object into it to avoid
electrical shock or fire.
Be sure to turn off the projector and unplug the
power cord before replacing the lamp.
EN-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
TECHNICAL SPECIFICATIONS
Projection System
Resolution (Pixels)
Image Brightness
Uniformity
3 panel 0.7 inch LCD projector
1024 x 768 (786,432 dot x 3)
1300 ANSI Lumen (Typical)
85%
Lens
Manual Zoom (1.3X)
21.5~ 28mm
Focal Length
Contrast Ratio
Screen Size
400:1
40 ~ 200 inches
Front, Rear, Ceiling
35dBA
Projection Type
Sound Noise
Lamp
150Watt EHP
Scanning Frequency
Horizontal frequency
Vertical frequency
Pixel Rate
15~91 KHz
50~85 Hz
12~157MHz
Computer
VGA(resized), SVGA(resized)
XGA,SXGA(resized)
Vertical: +/- 15 degree
Horizontal: +/- 10 degree
Video window on graphics background
1Watt x 2
Digital Keystone
Correction
Picture in Picture (PIP)
Audio System
Video Input
NTSC, PAL, SECAM
Computer, DVI, HDTV, YCbCr, S-Video, Video
PS2 & USB
Input Source
Remote Mouse
Remote Controller
OSD Language
Multifunctional
Multilanguage
(Language can be added upon request)
5 ~ 35 degrees C
Operation Temperature
Operation Humidity
Certifications
35 ~ 85%
UL, CE, FCC B
Power Requirement
Power Consumption
Dimension (WxDxH)
Weight
100~240v, 50~60Hz
210Watt
270 x 210 x 70mm
2.6kg
Designs and specifications are subject to change without notice.
EN-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
APPENDIX A
Preset Signals
Preset signal
fH (kHz) fV (Hz)
Sync
Size
Video 60 Hz
15.734
15.625
15.734
59.940
50.000
59.940
Video 50 Hz
Component 60 Hz
S on G/Y or
Composite Sync
S on G/Y or
Composite Sync
H(+), V(-)
H(+), V(-)
H(-), V(+)
H(-), V(+)
H(-), V(+)
H(-), V(+)
H(-), V(-)
Component 50 Hz
15.625
50.000
640 x 350 VGA mode 1
31.469
37.861
31.469
37.861
31.500
37.927
31.469
37.861
37.500
43.269
70.086
85.080
59.941
85.080
70.087
85.038
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
60.004
70.069
75.029
84.997
70.016
75.000
85.057
60.000
75.000
85.002
60.020
75.025
85.024
800
832
VGA VESA 85 Hz
640 x 400 VGA 60 Hz
VGA 85Hz
800
832
720 x 400 VGA mode 2
900
VGA VESA 85 Hz
640 x 480 VGA mode 3
VGA VESA 72 Hz
936
800
H(-), V(-)
832
VGA VESA 75 Hz
VGA VESA 85 Hz
H(-), V(-)
840
H(-), V(-)
832
800 x 600
SVGA VESA 56 Hz 35.156
SVGA VESA 60 Hz 37.879
SVGA VESA 72 Hz 48.077
SVGA VESA 75 Hz 46.875
SVGA VESA 85 Hz 53.674
H(+), V(+)
H(+), V(+)
H(+), V(+)
H(+), V(+)
H(+), V(+)
H(-), V(-)
1024
1056
1040
1056
1048
1344
1328
1312
1376
1472
1600
1568
1800
1680
1728
1688
1688
1728
1024 x 768 XGA VESA 60 Hz
XGA VESA 70 Hz
48.363
56.476
60.023
68.677
H(-), V(-)
XGA VESA 75 Hz
H(+), V(+)
H(+), V(+)
H(+), V(+)
H(+), V(+)
H(+), V(+)
H(+), V(+)
H(+), V(+)
H(+), V(+)
H(+), V(+)
H(+), V(+)
H(+), V(+)
XGA VESA 85 Hz
1152 x 864 SXGA VESA 70 Hz 63.995
SXGA VESA 75 Hz 67.500
SXGA VESA 85 Hz 77.487
1280 x 960 SXGA VESA 60 Hz 60.000
SXGA VESA 75 Hz 75.000
SXGA VESA 85 Hz 77.094
1280 x 1024 SXGA VESA 60 Hz 63.981
SXGA VESA 75 Hz 79.976
SXGA VESA 85 Hz 91.146
EN-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
HDTV Preset Signals
Preset Signals
Horizontal
Active Pixel
720
Vertical Active
Pixel
fH(kHz)
fV(Hz)
480p
720p
1080i
480
31.469
45.000
33.716
59.940
60.000
29.970
1280
720
1920
1080
EN-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Mouse cable (for USB)
Computer
USB port
Mouse Cable
Projector
Control port
Mouse cable (for PS/2)
Computer
Mouse Cable
PS/2 port
Projector
Control port
Monitor OUT cable (for data)
OUT
Display Set
IN
Monitor IN
Monitor OUT Cable
EN-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Connecting the Computer (data)
Projector
IN
Computer
OUT
Computer Cable
DVI or VGA OUT
Connecting the HDTV (data)
IN
IN
OUT
Audio OUT
Audio IN
Audio Cable
HDTV
OUT
HDTV to DVI Cable
Green,Blue,Red
OUT
EN-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
User’sManual
Connecting to a Video Source
(S-Video, Component, Composite)
Y Cb Cr (Component Video Cable)
S-Video Cable OUT
IN
OUT
IN
DVD Player
Y
R/W
OUT
AV Composite Cable
Video out VCR
EN-40
Download from Www.Somanuals.com. All Manuals Search And Download.
|