F O O D S E R V I C E
Owner’s Manual
Read And Save These Instructions
TM
Bar Boss, Drink Machine
®
®
Vita-Prep & Vita-Pro
High-Performance Commercial Blenders
Includes: Bar Boss • Two-Step Timer • Two-Speed
Variable Speed • Single-Step Timer • Vita-Prep • Vita-Pro
All Models
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safeguards
Important Safeguards
1. Read all instructions.
18. CAUTION: On all units with timers the light in the front panel START/STOP switch,
when lit, indicates the power to blender is ON and blender could start. Turn power
off before touching movable parts.
2. To protect against risk of electrical shock, do not put motor base in water or other
liquid.
19. WARNING: When processing hot liquids:
3. Close adult supervision is necessary when appliance is used by or near children.
4. Unplug the power cord from the wall outlet when the Vita-Mix® blender is not in
use, before disassembling, putting on or taking off parts, and before cleaning other
than washing the container.
• The 2-part latching lid must be securely in place. This allows steam to escape
naturally, and will prevent the lid from coming off when the machine is turned on.
• Do not start on HIGH speed. Always start hot liquids on LOW speed then switch
to HIGH speed while the machine is running.
5. Never contact moving parts, especially the blades.
• Use caution with hot liquids. Spraying from under the lid plug can occur,
or escaping steam may cause scalding.
• Do not process hot liquids with the Vita-Mix non-latching lid.
6. Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions or is dropped or damaged in any manner. Call Vita-Mix Service,
(800) 4DRINK4, (800-437-4654) or (440) 235-0214 at once for possible
replacement, examination, repair, electrical or mechanical adjustment. If you
live outside the USA, contact your Vita-Mix Distributor.
Save These Safety Instructions
7. The use of attachments not recommended or sold by Vita-Mix Corporation may
cause fire, shock, or injury.
8. Do not use outdoors.
Enjoy the safety of this grounded appliance. The Vita-Mix blender’s U.S. power cord
comes equipped with a three-prong (grounding) plug which mates with a standard
three-prong wall outlet (Figure A).
9. Do not let the power cord hang over edge of table or counter, or touch hot surfaces.
10. Keep hands and utensils out of container while motor is running to prevent the
possibility of severe personal injury and/or damage to the Vita-Mix blender. A
rubber scraper may be used, but only when the Vita-Mix Drink blender is not
running. The tamper may be used while motor is running with the main part of
the lid in place.
Adapters (Figure B) are available for two-prong outlets. Do not cut or remove the third
(ground) prong from the plug or power cord.
Consult your electrician if you are not sure if the wall outlet is grounded through the
building wiring. With a properly grounded two prong wall outlet, ground the machine by
attaching the tab on the adapter to the wall outlet cover by means of the screw in the
center of the cover (Figure B).
11. WARNING: Blade is sharp. Handle carefully.
• Never try to remove blade while container is sitting on the motor base.
• Do not operate with loose, nicked or damaged blade - replace immediately.
• To reduce the risk of personal injury, never place blade assembly on motor base
without blender container properly attached.
THREE PRONG
ADAPTERS
12. The maximum capacity is equivalent to the ounces listed on the container, i.e. 64
oz. (2 liter), 48 oz. (1.4 liter) and substantially less with thick mixtures.
13. Container should not be more than 2/3 full when the tamper is left in place while
blending. Do not exceed 30 seconds of continuous blending with tamper in place.
14. When making peanut butter (or other nut butters, or oil based foods) do not
process for more than one minute after mixture starts circulating. Over-processing
will cause the mixture in the container to overheat.
ARE NOT TO
BE USED IN
Figure A
Figure B
CANADA.
15. CAUTION: Cooling problems resulting in thermal shut-off and eventual motor
damage may result if machine is operated in sound chambers other than those
approved by Vita-Mix.
16. Always operate the Vita-Mix blender with a lid in place.
17. The maximum capacity is equivlaent to the ounces (liters) listed on the container,
i.e. 64 oz. (2 liter), 48 oz. (1.4 liter), and substantially less with thick mixtures.
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20 or 45 Second Timer
Model
NOTE: Blenders come with several different control options. Please be sure you are
following the instructions for your blender model.
ON
ON/OFF switch. Up for ON. Down for OFF.
All times are at HIGH speed. During operation,
you may interrupt timer by turning power
switch OFF.
F
OF
T
R
R
A
IM
T
S
T
E
Two-Step Timer Model
ON/OFF switch. Up for ON. Down for OFF.
All times are total times. During operation, you
may interrupt timer by pressing START/STOP
switch.
TIMER dial. Allows user to select a number
of timed settings. Increments on timer are
approximate seconds. Timer is activated only
when the power switch is ON. Blender will shut
off automatically at the end of the pre-set time.
:30
:25
ON
:20
:15
OFF
:10
P
O
ST
T/
R
A
ST
ER
IM
T
TIMER DIAL. Allows user to select a number
of timed settings. Increments on timer are
approximate seconds. Timer is activated only
when the power switch is ON. Blender will shut
off automatically at the end of the pre-set time.
START TIMER switch. This is a lighted switch.
When light is lit power is on. Depress START
TIMER switch to activate timer setting.
Note on Two-Step Timers: Stop mid
cycle with START/STOP switch, not
the power switch. If the power switch
was used, wait 30 seconds for power
to recycle and the timer to reset
before resuming operation.
START TIMER switch. This is a lighted switch.
When light is lit power is on. Depress START
TIMER switch to activate timer setting and again
to stop midcycle.
Bar Boss Timer Model
ON/OFF switch. Located on the front of the
machine below the switch panel, controls the
power to the machine. With the machine plugged
in, switch the machine to ON to ready the
machine for blending. Shut OFF power switch
at night or whenever the machine will be left
unattended.
Two-Speed Model
ON/OFF switch. Up for ON. Down for OFF.
Note on Bar Boss Timers: Stop mid
cycle with START/STOP switch, not
the ON/OFF switch. If the ON/OFF
switch was used, wait 30 seconds for
power to recycle and the timer to
reset before resuming operation.
F
F
O
HIGH/LOW switch. Up for HIGH. Down for LOW.
I
START TIMER switch. This is a lighted switch.
When light is lit power is on. Depress START
TIMER switch to activate timer setting and again
to stop midcycle.
Variable Speed Model
ON/OFF switch. Up for ON; down for OFF.
6
5
7
4
H
IG
H
8
3
During operation, you may interrupt timer by
pressing START/STOP switch.
9
HIGH/VARIABLE switch. HIGH overrides the
VARIABLE SPEED dial and is the fastest speed
available. VARIABLE speed is required to use
the VARIABLE SPEED dial.
2
FF
O
0
E
L
B
IA
R
A
V
1
TIMER DIAL. Allows user to select a number
of timed settings. Increments on timer are
approximate seconds. Timer is activated only
when the power switch is ON. Blender will shut
off automatically at the end of the pre-set time.
VARIABLE SPEED dial. Allows user to select
continuously variable motor speeds ranging
from 1,000 rpm to 24,000 rpm. Active only
when HIGH/VARIABLE switch is set on
VARIABLE position.
PULSE switch. Pulse button can only be used
when the power switch is ON. The PULSE
switch can be used to quickly refresh product
in the container by depressing the switch and
holding down as long as needed.
NOTE: Switches will become sticky from use. Use a wet cloth or sponge to flush and
clean in the groove around the water-shielded switches. You may also lightly spray
the surface around the switches with an all purpose cleaner such as Cinch® or 409®
and work the switches back and forth a few times to loosen any dried residue under
switch. Leaving switches sticky will damage or burn out the switches.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Lids come in several different styles. Please be sure you are following the
instructions for your style of lid.
NOTE: Lids come in several different styles. Please be sure you are following the
instructions for your style of lid.
To secure lid plug, rotate
it so one tab locks
Figure D
Two-Part Lid
Two-Part Lid
between the stops on
top of rubber lid
64 oz. (2 liter) Polycarbonate container
The two part lid is easy to clean and easy
to put on and take off. (Note: Brand new lids
are a little stiff. This is temporary.)
Press in above
container tab
to remove lid
48 oz. (1.4 liter) Polycarbonate stackable
container
The two part lid is easy to clean and easy to
put on, take off and seal.
• The lid has a continuous rim which latches
inside the container tabs. Push one side of
the rim under one tab, and with the heel of
• To remove fully latched lid, squeeze tabs
together on both sides of the container,
pull upward and off.
Rim
your hands push down, over the opposite tab,
to snap lid into position.
• To remove lid, place hands around the lid,
pressing thumbs above one of the container
tabs. Push in and lift off.
• The center lid plug can be removed when
using the tamper. Twist plug to fasten
or remove.
• The center lid plug can be removed when
using the tamper. Twist plug to fasten
or remove.
Container
tab
CUPS
B(1) Unsealed/unlatched
B(2) Sealed
B(3) Fully Latched
Figure A
Always latch lid when processing hot
liquids. See warning on page 3.
1 Piece Lid
(Lid resting on container
using hand to stabilize.)
(Lid pushed into container.
Side latches are not under
container lip.)
(Side latches are snapped
under container lip.)
64 oz. (2 liter) Polycarbonate container
The one piece lid is easy to put on or take off,
and to clean, for quick operation. (Note: Brand
new lids are a little stiff. This is temporary.)
• There is no latch on this lid. Simply hold the
lid on when starting.
CUPS
• Add ingredients through port in top.
NOTE: To make new lids easier to insert and remove, rub a light coating of cooking oil
around bottom where it seals. Place it in container for several minutes, remove and
lightly wipe oil off lid.
Caution: Do not use non-latching lid when
processing hot ingredients. Not for use with
a tamper.
Figure C
NOTE: To make new lids easier to insert and remove, rub a light coating of cooking oil
around bottom where it seals. Place it in container for several minutes, remove and
lightly wipe oil off lid.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
Bar Boss and Timer Blender Instructions
1. Set the container on the motor base by aligning it over the centering pad anchored to
the base. (Motor must be completely stopped before positioning container). Containers
are not to be used for hard, dry materials. Avoid running your Bar Boss/Timer Blender with
the container empty.
How to operate your Two-Speed or Variable
®
Speed Drink Machines, Vita-Pro and
2. Place liquids and soft foods in the container first, solid items and ice last. Prepare
food by cutting or breaking into 1-3 inch (3-8 cm) pieces. Frozen fruit should be as small
as practical.
®
Vita-Prep.
1. Set the container on the motor base by aligning it over the centering pad anchored to
the base. (Motor must be completely stopped before positioning container.) Containers
are not to be used for hard, dry materials. Avoid running the blender with the
container empty.
3. Position lid on the container. If blending hot ingredients, the lid must be securely in
place. When processing hot liquids, DO NOT use the non-latching lid.
4. Press ON/OFF switch to ON. Activate the timer by selecting the desired timer setting
on the dial and then depressing the START/STOP TIMER switch on the left.
4a. If mixture stops circulating, you have likely trapped an air bubble. Either insert the
tamper through the lid while blending, or stop the motor remove the container from
the base and stir or scrape the mixture from the sides of container into the center
using a rubber spatula to press any air bubbles away from the blades. Replace the
lid and continue blending.
2. Place liquids and soft foods in container first, solid items and ice last. Prepare food by
cutting or breaking into 1-3 inch (3-8 cm) pieces. Frozen fruit, should be as small as
practical. Thawed or partially thawed fruit is recommended. High-speed is recommended
for heavy-duty blending.
3. Always use a lid when blending. If blending hot ingredients, the lid must be securely in
place. When processing hot liquids, DO NOT use the non-latching lid.
4. Select desired speed setting. Most foods are blended on HIGH speed. Start heavy or
thick foods on the recommended speed then switch to HIGH once the mixture begins
processing. If mixture stops circulating insert the tamper through the lid while blending
(see page 11), or stop the motor, remove container and stir or scrape the mixture from
the sides of container into the center using a rubber spatula. Replace the lid and
continue blending.
Note: START/STOP TIMER switch on your machine is lit when power is on. Avoid
moveable parts. The timer stops working if machine is overloaded on low speed.
Reset by turning power off for 15 seconds.
Warning: If you detect a change in the sound of the machine or if a hard or
foreign object comes into contact with the blades, do not serve the drink.
Inspect your blade assembly for loose, nicked or missing parts. If parts are
loose, missing, or nicked replace with new blade assembly. (See page 10.)
4b. To prevent possible splashing, lightly rest your hand on the lid while turning the
machine on (except when processing hot liquids).
Warning: If you detect a change in the sound of the machine or if a hard or
foreign object comes into contact with the blades, do not serve the drink/food.
Inspect your blade assembly for loose, nicked or missing parts. If parts are
loose, missing or nicked replace with new blade assembly. (See page 10).
5. To prevent possible splashing, lightly rest your hand on the lid while turning the machine
on (except when processing hot liquids).
4c. Due to the blending speed of the machine, processing times are greatly reduced
over standard machines. Until you become accustomed to the speed, watch your
mixture carefully to avoid over-blending.
4d. If stopping the machine mid cycle, use the START/STOP switch, not the POWER
switch. If the POWER switch was used, wait 30 seconds for power to recycle and
the timer to reset before resuming operation.
6. Due to the speed of the machine, processing times are greatly reduced over standard
machines. Until you become accustomed to the speed, count your time carefully by
watching the second hand of a clock, or count slowly to avoid over blending.
7. After blender has been turned off, wait until the blade has come to a complete stop before
removing the lid or container from the motor base. Note: The thermal protector shuts the
motor off to protect it from overheating. To restart, wait for motor to cool down with the
power off (up to 30 minutes). Note: Cooling may be quickened by placing the motor
base in a refrigerator or a cool spot. (Unplug first.) To speed up the process try circulating
the air with a vacuum or fan aimed at the bottom of the base. When this happens,
review your processing techniques and your instructions. Your recipes may: 1) be too
thick - add liquid; 2) be processed too long at too low a speed setting. Use HIGH speed
whenever possible. If the motor seems to be overheating (and the thermal overload
protector has not turned the machine off), remove the container from the base. Set
the dial on LOW (#10). Turn the machine ON and let the machine run for one minute.
8. Up to 6 feet (1.8 meters) of power cord is available for use and is secured by plastic
cord retainer clips underneath the motor base. Do not let the power cord hang over
edge of counter or touch hot surfaces.
5. After blender has been turned off, wait until blade comes to a complete stop before
removing the lid or container from the motor base.
Note: The thermal protector shuts the motor off to protect it from overheating. To restart,
wait for motor to cool down with the power off (up to 30 minutes). When this happens,
review your processing techniques and your instructions. Your recipes may be too thick
or have too much material in them.
Cooling may be quickened by placing the motor base in a refrigerator or a cool spot.
Unplug first. To speed up the process try circulating the air with a vacuum or fan aimed
at the bottom of the base. If the motor seems to be over heating (and the thermal
overload protector has not turned the machine off), remove the container from the
base. Set the timer for 20 seconds. Turn the machine ON and let the machine run for
20 seconds. Repeat this step 3 times for a total of 1 minute.
6. To use the pulse switch on the Bar Boss blender: Press ON/OFF switch to ON.
With the container on the motor base depress the pulse switch. Release the switch to
turn off the motor.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Agitator Assembly. Use caution when handling
the blade; it is sharp. When inserting the blade
assembly through the container bottom, align the flat
sides. Gravity holds it in place while the retainer nut is
tightened. Do not attempt to disassemble this part.
The tamper prevents an air bubble from
forming while blending. It is used when
making frozen ice creams, pureeing fruits
and vegetables, making peanut butter (or
whenever your mixture requires it). It also
permits you to push ingredients down
around the blades while the Vita-Mix
blender is running.
Drive Spline. Mates with drive socket on the motor
base to turn the blade. Note: Removing and replacing
your container while the coupling is still rotating will
strip the drive spline “teeth”. (This part is NOT
removable.)
Tamper use:
• Use only with the lid in place and the
center lid plug removed.
• The splash disc prevents the tamper
from hitting the blades when inserted
through the lid.
• Container should not be more than
2/3 full when the tamper is left in place
while blending.
Retainer Nut. Must be snug. Order the available
retainer nut wrench for best results. (Refer to the
diagram below to remove or replace.)
Never use a blade assembly
with loose, damaged or nicked
components.
• To avoid overheating, do not exceed
30 seconds of continuous blending
with tamper in place.
• If thick mixtures stop circulating, you
have likely trapped an air bubble.
Insert tamper through the lid and stir
to release it.
• Holding the tamper at an angle near
the side and pushing towards the
center will be more effective when
creating a thicker, smoother drink.
Retainer Nut Removal
• The retainer nut is easily removed
using a standard 6” (15 cm) screw-
driver. Turn container upside down
and insert screwdriver shaft between
the lobe and drive spline. Push the
screwdriver handle counterclockwise
to loosen nut. Once loosened, remove
by hand.
*NOTE: Tampers have a small step on
them. The step prevents contact of the
tamper with the blades in the 48 oz. (1.4 liter)
polycarbonate containers. Tampers cannot
be used with one piece non-latching lid.
Lobe
Retainer Nut
Drive Spline
Container (bottom view)
• To replace, position retainer nut on top
of blade assembly and hand tighten.
Then, using the screwdriver, tighten
clockwise until it stops. If it is not tight
enough, you will notice increased
container noise.
Warning
When processing hot liquids always:
• Use caution; escaping steam or splatters may scald.
• Completely latch the lid; this will prevent expansion from blowing it off when the
machine is turned on.
• Start on LOW speed then switch to HIGH speed. Never start on HIGH speed with
hot ingredients.
• Do not process hot ingredients with the non-latching lid.
Available: For best results we recommend using
a Retainer Nut Wrench in place of screwdriver.
To order ask for Item #1222.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
®
®
Bar Boss, Drink Machine
NOTE: Blenders come in several similar styles. Please be sure you are following
the parts list for your blender model.
Item # Part
Vita-Pro and Vita-Prep
NOTE: Blenders come in several similar styles. Please be sure you are following the
parts list for your blender model.
Item # Part
#755
#1195
#760
#791
PLS132
#802
Polycarbonate lid plug - 64 oz. (2 liter)
Polycarbonate container, wet blade assembly & lid - 64 oz. (2 liter)
Tamper
#755
#756
#760
#791
Polycarbonate lid plug - 64 oz. (2 liter)
Polycarbonate container, ice blade assembly & lid - 64 oz. (2 liter)
Tamper
Sound-reducing centering pad
Sound-reducing centering pad
Variable speed control knob / timer control knob
Drive socket
Owner’s Manual
Heavy-duty retainer nut
Agitator assembly (wet blades)
48 oz. (1.4 liter) polycarbonate stackable container lid plug
Lid assembly for polycarbonate container - 64 oz. (2 liter)
Lid only (no plug) for polycarbonate container - 64 oz. (2 liter)
Retainer nut wrench
1-piece thermoplastic rubber lid for 64 oz. (2 liter) container
48 oz. (1.4 liter) polycarbonate stackable container,
wet blade & lid assembly
PLS132
#802
XDM034
#836
#1151
#1191
#1192
#1222
#1159
PLS145
#15506
Variable speed control knob / timer control knob
Drive socket
Owner’s Manual
Heavy-duty retainer nut
Agitator assembly (ice blades)
Lid assembly for polycarbonate container- 64 oz. (2 liter)
Lid only (no plug) for polycarbonate container - 64 oz. (2 liter)
Retainer nut wrench
48 oz. (1.4 liter) polycarbonate stackable container lid plug
1-piece thermoplastic rubber lid for 64 oz. (2 liter) container
48 oz. (1.4 liter) polycarbonate stackable container,
ice blade & lid assembly
XDM034
#836
#1152
#1159
#1191
#1192
#1222
PLS145
#15504
#15502
#15507
48 oz. (1.4 liter) polycarbonate stackable container only
2-piece thermoplastic rubber lid for 48 oz. (1.4 liter) stackable container
#15502
#15507
48 oz. (1.4 liter) polycarbonate stackable container only
2-piece thermoplastic rubber lid for 48 oz. (1.4 liter) stackable container
*Notice: Other than the drive socket, blade assembly, and retainer nut, this unit is not
user serviceable.
*Notice: Other than the drive socket, blade assembly and retainer nut, this unit
is not user serviceable.
#1159
#15507
#755
#755
#1191
#1195
#1191
#1222
#1192
PLS145
#1192
#15504
#15502
(container
without
blade or lid)
#1159
#756
#1152
#836
#1151
#760
#15507
#836
#791
#802
#791
#802
#15506
#15502
(container
#760
without
blade or lid)
PLS145
PLS132
PLS132
#1222
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Care Note
Motor Base
1. Unplug the power cord.
To ensure that you get the longest possible life from your Vita-Mix product, we recom-
mend the following products, when used as directed by the supplier:
2. Wash outside surface with a damp, soft cloth or sponge, which has been rinsed in a
mild solution of liquid dish soap (Ivory Liquid® or equivalent) in warm water. NEVER
IMMERSE MOTOR BASE IN WATER OR OTHER LIQUID.
Cleaning Product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supplier
Solid Supra, Solid Power,.. . . . . . . . . . . . . . . . . . . . . . . . Ecolab, Inc., St. Paul, MN
Guardian Acclaim, Solid Guardian Plus, . . . . . . . . . . . . . (800) 352-5326
Diverpak. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diversey, Livonia, MI
Eclipse H2, Liqui-Safe L7 . . . . . . . . . . . . . . . . . . . . . . . . (800) 521-8140
Acclean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Klenzade Products
Poly-Brite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Division of Ecolab
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . St. Paul, MN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (612) 293-2165
Glow MB-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wesmar Company, Inc.
Lustre NC-25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seattle, WA
Lustre Plus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (206)783-5344
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . www.wesmar.com
PSRA 41-D, PSRA 41-E . . . . . . . . . . . . . . . . . . . . . . . . . Anderson Chemical Co.
Liqui-Ware 1, Liqui-Ware MC . . . . . . . . . . . . . . . . . . . . . Litchfield, MN
D-Flex, Sur-Met . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (800) 366-2477
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . www.andersonchemical.com
3. Thoroughly clean switches so that they work freely. They will become sticky from
use. Use a wet cloth or sponge* to flush and clean in the groove around the water
shielded switches. You may also lightly spray the surface around the switches with
an all-purpose cleaner such as Cinch® or 409® and work the switches back and forth
a few times to loosen any dried residue under switch.
4. Polish with a soft cloth.
* Note: Be sure to wring excess water out of cloth or sponge when cleaning around the
controls or any electrical part.
Lid
Separate the lid and plug, then wash in warm soapy water. Rinse clean under running
water and dry. Reassemble before use. (See pages 6 and 7).
Container
1. To clean: Fill pitcher 1/4 full with warm (110˚F/43˚C) water and add a couple drops
of dish soap**. Return container to motor base and firmly position the two part lid.
Run machine for 30 seconds. Empty container. Repeat this step.
** Note: To prolong polycarbonate container life, Vita-Mix recommends using soaps
with a low Ph balance, such as a manual pot and pan detergent. Due to the nature
of polycarbonates, automatic dishwashing is not recommended.
2. Fill pitcher 3/4 full with warm (110˚F/43˚C) water (do not add soap). Return container
to motor base and firmly position the two part lid. Run machine for 30 seconds.
Empty container.
Rinse Aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supplier
Solid Rinse Dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ecolab, Inc., St. Paul, MN
Solid Brilliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (800) 352-8140
Destainer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supplier
NuWare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diversey, Livonia, MI
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (800) 521-8140
NOTE: Switches will become sticky from use. Use a wet cloth or sponge to flush and
clean in the groove around the water-shielded switches. You may also lightly spray the
surface around the switches with an all-purpose cleaner such as Cinch® or 409® and
work the switches back and forth a few times to loosen any dried residue under switch.
Dirty switches may burn out.
ADDITIONAL NOTE: Do not let mixtures, liquids and food products dry within the
container. Rinse throughout use. Drying may lock around the blade and weaken/tear
the bearings seal when restarted. Do not place containers in the freezer. Extremely
low temperature combined with hot ingredients and/or the immediate rapid action of
the blade may crack the container. Due to the nature of polycarbonates, microwaving
and automatic dishwashing are not recommended. Follow the cleaning instructions on
page 15.
3. If any solid residue remains, remove the blade agitator assembly (see page 10) and
wash all container parts in warm soapy water. Rinse and drain. Reassemble before
next step.
4. To sanitize: If all solid residue is gone after step 2 or after completion of step 3,
fill container 3/4 full with a sanitizing solution mix.*** Return container to motor base
and firmly position the two part lid. Run machine on HIGH for 30 seconds. Empty
container.
5. Return container to motor base and run machine empty for an additional 5 seconds.
Do not rinse after sanitizing.
*** Recommended sanitizing solution: 1-1/2 teaspoons Chlorox® institutional or house-
hold bleach in 2 quarts (2 liter) water.
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Top four problems you can fix on your own
Dimensions:
Height of Motor Base: 8-1/2” (21.25 cm)
• with 64 oz (2 liter) Polycarbonate container and lid: 20” (50 cm)
1. Problem:
Solution #1:
• increased vibration
• leaking from bottom of container
• increased container noise
Check blade assembly for loose, damaged
or nicked components and replace.
Solution #2:
• with 64 oz (2 liter) Polycarbonate container without lid: 18” (45 cm)
• with 48 oz (1.4 liter) Polycarbonate container and lid: 17-1/2” (46.75 cm)
• with 48 oz (1.4 liter) Polycarbonate container without lid: 9-1/4” (44.75 cm)
64 oz (2 liter) Polycarbonate Container with lid, no base: 12-3/4” (32 cm)
48 oz (1.4 liter) Polycarbonate Container with lid, no base: 10” (25.5 cm)
Dimensions: 8” W x 9” D x 20” H (20.3 cm x 22.9 cm x 51 cm)
Ship weight of machine: 13 lbs. (6 kg)
Tighten retainer nut with screwdriver
moving clockwise until it is snug. See p. 10.
2. Problem:
• Machine will not run.
Solution #1:
Double-check to make sure power cord is
firmly in power outlet.
Solution #2:
Check to make sure switches are clean
and moving freely.
Solution #3:
The thermal protector may have turned the
machine off. Turn power off for up to 30
minutes to reset. Note: Cooling may be
quickened by placing the motor base in a
refrigerator or cool spot. (Unplug first). To
speed up the cooling process, try circulat-
ing the air with a fan or vacuum at the bot-
tom of the motor base.
Power Requirements:
Volts: 100 VAC
Watts: 900
Hz: 50/60
Volts: 120 VAC
Amps: 11.5
Hz: 50/60
Volts: 220/240 VAC
Watts: 750-850
Hz: 50/60
3. Problem:
Solution:
• loud noise from blade area
• blades don’t spin
Drive Socket may be broken. Check for a
fine crack down the center or worn teeth-
replace with a new drive socket. (Item #
802). Instructions are included with part.
4. Problem:
Solution:
• Bar Boss/Timer Blender will not run
when START TIMER switch is
activated.
Check ON/OFF switch to make sure the
switch is in the ON position. Note: START
TIMER switch is lit when power is on.
On Two-Step Timers:
Timer stops working if machine is overloaded on low speed. Reset by turning power
off for 15 seconds. Do not turn power off midway through a blending cycle. To interrupt
cycle, press START/STOP TIMER switch one time. See page 9.
The instructions appearing in this Owner’s Manual cannot cover every possible
condition and situation that may occur. Common sense and caution must be
practiced when operating and maintaining any appliance.
If you cannot fix your machine with these suggestions, technical help is available by
calling 800-4DRINK4 (800-437-4654). If you live outside the USA, contact your local
Vita-Mix distributor.
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Vita-Mix Corporation warrants your Commercial Vita-Mix appliance to be free from
defects in materials and workmanship for a period of three years from the date of
purchase when used in accordance with the accompanying instruction booklet.
PLEASE NOTE: The Service Contract outlined in the following paragraphs applies only
to customers in the United States and Canada. Customers in all other countries should
contact their local Vita-Mix distributor for service details.
Provisions of this limited warranty are void if your Vita-Mix appliance has been
subjected to obvious abuse, negligence, accident, alteration, or failure to follow
operating instructions, or product exposure to abnormal or extreme conditions.
Cosmetic changes such as discoloration of parts of the product in the hands of the
user or the effects of the use of abrasive cleaners will not be warranted or considered
defects. The cleaning or removal of food products along with any damage caused by
allowing them to build up is not covered by this limited warranty. Warranty is void if
the Vita-Mix blender is put into a sound reduction chamber that does not allow proper
cooling.
This Vita-Mix blender includes a 1-Year Service Contract effective from date of
purchase. Proof of date of purchase may be required.
The Vita-Mix Service Contract includes the following:
1. Only one extra drive socket - to facilitate simple repairs and prevent down time is
included and packaged with each machine.
2. Additional drivers and tamper, unless defective, are not covered. NOTE: to determine
if you have a defective part, please order a replacement part through Vita-Mix
Customer Service and, when the new part arrives, return the old part in the same
packaging. Vita-Mix will inspect the returned part and, if defective, issue a refund for
the price of the new part. A part will be considered defective if no abuse or neglect
was involved with its break. Non defective parts sent to Vita-Mix for inspection will
not be returned if deemed unusable. Service Contract covers functionality of the
machine but not abuse or lack of recommended maintenance.
In the event your Vita-Mix appliance needs service or repair covered by the terms of
this warranty, please call the Vita-Mix Corporation for shipping instructions. The Vita-Mix
blender must be sent in original or sufficient packaging.
This limited warranty is in lieu of any other warranty expressed or implied. No
representative or any other person is authorized to make any other warranty or to
assume any liability not strictly in accordance with the foregoing. This limited warranty
gives you specific legal rights which may vary from state to state. Proof of purchase
may be required to prove date of purchase.
3. In the Continental United States, sender pays freight one way to Vita-Mix
Corporation. The Vita-Mix Corporation will pay UPS ground freight charges to return
the machine to the sender. Sender pays costs for special shipping requests. Outside
Continental United States, other service contracts may apply.
Outside the Continental U.S.A. other warranties may apply. (Call or check with your
Vita-Mix distributor for details). In case of shipping damage, notify the shipper or carrier
immediately. Outside the USA, contact your local Vita-Mix Distributor.
Before returning this product for any reason, including repair, please, first contact our
CUSTOMER SERVICE DEPARTMENT: (800) 4DRINK4, (800) 437-4654 or (440) 235-0214
to receive a “RETURN AUTHORIZATION NUMBER”.
Note: Within the United States, Limited Warranty and Service Contract are honored
directly through the Vita-Mix Corporation, Cleveland, Ohio USA. Non-warranty repairs
can be performed by any CFESA service center. For machines sold in the USA, call
Vita-Mix (800) 4DRINK4 (800-437-4654) or (440) 235-0214.
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
VITA-MIX® CORPORATION
Foodservice Division
8615 Usher Road, Cleveland, Ohio 44138-2103 USA
©2002 Vita-Mix Corporation. No part of this publication may be reproduced or transmitted in any form or
by any means, electronic or mechanical, including photocopy, recording or any information storage and retrieval system
without the written permission of the Vita-Mix Corporation.
Printed in U.S.A
XDM034 3/03
Download from Www.Somanuals.com. All Manuals Search And Download.
|