STEP
5
AUTO-CALIBRATION
DO NOT STAND ON THE BELT WHEN PERFORMING AUTO-CALIBRATION
You need to access User Engineering Mode to run the auto-calibration. With the safety key in place, please hold
down SPEED DOWN and ENTER for 5 seconds. When in the User mode, “USER ENG MODE” appears in the
alphanumeric window. To access the data press the ELEVATION keys until “AUTO-CALIBRATION” appears.
To begin auto-calibration, press ENTER. The treadmill will run through minimum and maximum speed and
maximum incline. This will take 3-5 minutes. Let the treadmill perform this complete function before exiting the
Engineering Mode.
Elevation A/D appears in the left window. PWM value appears in the dot matrix window, and speed appears in
the right window. “CALIBRATION PASSED” will appear in the alphanumeric window when the auto-calibration is
complete. The treadmill will come to a complete stop and return to the start-up screen in the alphanumeric window.
A s s e m b l y
G u i d e
500 South CP Avenue
toll free 800.335.4348
•
P.O. Box 280
•
Lake Mills, WI 53551
fax 920.648.3373
T9800 Series
•
phone 920.648.4090
•
TREADMILLS
©2007 Vision Fitness. All Rights Reserved. 5.07
AG18.39PRD
REV7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP
3
PINK BAG
A s s e m b l y
G u i d e
• Insert the handlebar cover onto the
handlebar. Insert the right handlebar
by holding the handlebar sideways
toward the treadmill and inserting the
top into the console. Rotate the
handlebar into the bracket located on
the console mast. Fasten with a bolt
(M5x12L), and a bolt (M6x15L socket
head) & an arc washer (6.5x13x1T)
into the two holes of the console plas-
tic, and a bolt (M8x15L flat head) into
the hole in the handlebar. Fasten a bolt
(M6x15L socket head) and a flat washer
(6.5x19x2T) into the hole in the handle-
bar on the console mast. Do not fully
tighten the bolts.
T9800 Series
TREADMILLS
To avoid possible damage to this Platform Treadmill, please follow these assembly steps in the correct
order. Before proceeding though, find your new Platform Treadmill’s 2 serial numbers, located on the
underside of the main frame, and on the bottom of the console, and enter here:
STEP
2
• Slide the handlebar cover over the
bracket and secure with
(M6x15L socket head) and
washer (6.5x19x2T). Do not fully
tighten the bolt.
a
bolt
flat
Frame Serial Number
Console Serial Number
a
Refer to these numbers when calling for service, and also enter these serial numbers on your Warranty
Card and in your own records. Be sure to read your Owner’s Guide before using your new Platform Treadmill.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
STEP
3
• Repeat on the left side.
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Platform
Treadmill, to prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts
are in place and partially threaded in before completely tightening any ONE bolt.
• Fully tighten the console and
handlebar bolts.
STEP
4
MOTOR COVER
TV Power Cable
STEP
1
ORANGE BAG
• Place the motor cover back on the
frame and fasten with 6 screws.
Coaxial Cable
•
Remove motor cover screws and
• Attach the power cord to the treadmill.
take off the motor cover.
STEP
4
• Plug the power cord into the power
outlet.
• Insert the right console mast to the
right console mast bracket. First, fasten
the inside of the console mast to the
console mast bracket by securing four
bolts (M8x15L socket head) and four
washers (8.2x19x2T). Fully tighten the
bolts. Second, fasten the two bolts
(M10x20L button head) and two
washers (10.2x19x2T) on the front of
the console mast and fully tighten.
STEP
5
6
AUTO-CALIBRATION
TV BRACKET WIRING
Please refer to back cover for this
procedure, then return to Step 6.
• Repeat on the left side
STEP
1
STEP
BELT TENSION
STEP
2
BLUE BAG
• If the running belt slips when used,
run the treadmill at 2.0 mph and use
the supplied 8mm Allen wrench to turn
•
Tie the ribbon data cable, TV
power cable, and coaxial cable to
the cable wire tie on the top of the
right console mast. Feed the cables
down the console mast and through the
hole at the lower part of the console
mast. Remove protective plastic cover.
Push any remaining cable into the
console mast.
the left and right tension bolts clockwise
1
/4-turn at
a
time until the belt no
longer slips.
• If the running belt is too far to the
right side, run the treadmill at 2.0 mph
and use the supplied 8mm Allen
wrench to turn the right tension bolt
1
clockwise /4-turn at a time until the
• Mount the console onto the left and
right console masts using four bolts
(M8x15L socket head) and four washers
(8.2x19x2T). Do not fully tighten.
belt remains centered during use.
If the running belt is too far to the left
side, run the treadmill at 2.0 mph and
turn the left tension bolt clockwise
STEP
6
1
• Take the wire tie off the cables. Plug
the large 20-pin ribbon connector into
the 20-pin connector on the lower
control board. Attach the two grounding
wire connectors to the two grounding
wires located in the motor pan near
the front of the frame. Connect the TV
power cable to the TV power connector
and coaxial cable to the coaxial
cable connector; both located on the
inside of the motor compartment at the
front of the treadmill.
/4-turn at a time until the belt remains
centered during use.
Download from Www.Somanuals.com. All Manuals Search And Download.
|