Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1
MAINTENANCE PROCEDURE
Download from Www.Somanuals.com. All Manuals Search And Download.
PREVENTIVE MAINTENANCE SCHEDULE
VISION TREADMILL
Item
Daily Weekly Monthly Quarterly Biannual Annual
Console Mounting
Bolts
Inspect
Frame
Clean
Inspect
Inspect
Clean
(Vacuum)
Running Belt Top
#3 Carbon Brush
Power Cord
Inspect
Replace
Inspect
Inspect
Display Console
Handlebar
Clean
Clean
Inspect
Handrail &
Handlebar
Inspect
Clean
Front Roller
Inspect
Inspect
Rear Roller
Emergency Button
Tension Wheel
V Belt
Test
Inspect
Clean
Clean
Inspect
Inspect
Inspect &
Re-waxing
Deck Re-waxing
Running Belt
Control Box
Clean
(Vacuum)
Motor
Air Shock
Lubricate
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
TENSIONING THE BELT
Caution:
Over-tightening of the roller will severely shorten the life of the belt and may
cause further damage to other components.
Running Belt:
If when you plant
your foot on the belt,
you can feel a slipping
sensation then the belt
has stretched and is
slipping across the
rollers. This is a
normal and common adjustment on a new treadmill. To eliminate this
slipping, tension both the rear rollers Allen bolts 1/4 TURN as shown above.
Try the treadmill again to check for slipping. Repeat if necessary, but
NEVER TURN the roller bolts more than 1/4 turn at a time.
Perfect Tension o f Running Belt:
Drive Belt:
If you have tensioned the running belt and are still experiencing a
slipping, adjust the tension screw. Then try the treadmill again to check for
slipping.
Perfect Tension of Drive Belt:
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
DECK RE-WAXING PROCEDURE
Frequency: Every 1 month.
LUBE
Name: DOW CORNING 350 SILICON
Procedure:
1. Loosen the tension bolts at both ends.
2. Pull the belt with your left hand and apply the silicon in the deck with your
right hand. (The volume of silicon applied is about 25CC.)
3. Tighten the tension bolts.
4. Start the treadmill. Step on the treadmill belt to walk the silicon in.
Adjust the belt tension if necessary.
5. With the clamp-on meter, measure the current draw of the motor. (Clamp
on either the red or the black wire.) The current should be less than
15Amps for 110V model. (less than 7.5Amps for 220V model.)
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEAN THE GROOVES PROCEDURE
Frequency: Every 3 months.
Procedure:
1.Remove the drive belt and check the
grooves in belt for dirt or dust and clean it.
2.Check the grooves in motor pulley for dirt
or dust and clean it.
3Check the grooves in roller pulley for dirt or
dust and clean it.
If dirty grooves in the drive belt, motor and roller pulley, there will be noises while running.
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
LUBRICATING THE AIR SHOCK
Frequency: Every 6 months.
Procedure:
1.Fold up the frame by using the
deck-locking lever.
2.Add the lubricating oil on the shaft of the
air shock.
3.Lift the frame up and down, repeating
this several times to allow the lubricating
oil blend into air shock.
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2
WIRING DIAGRAM INSTRUCTION
Download from Www.Somanuals.com. All Manuals Search And Download.
T9700(TM51D/E) MCB WIRING(FOR 110V / 220V)
T2
T1
T6
T8
T5
T7
T3 T4
VR1
‹ T1-----Motor wire (black)
‹ T2-----Motor wire (red)
‹ T3-----D1 of on/off switch
‹ T4-----D3 of on/off switch
‹ T5-----20-pin console cable
‹ T6-----Elevation cable
‹ T7-----Speed sensor line
‹ T8----- Ground wire
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
T9600HRT(COMFORT)/T9600HRT/T9500HRT/T9450HRT/T935
0/T9300 MCB WIRING(FOR 110V / 220V)
T2 T1
T6
T9
T7
T8
T5
T3 T4
VR1
‹ T1-----Motor wire (black)
‹ T2-----Motor wire (red)
‹ T3-----D1 of on/off switch
‹ T4-----D3 of on/off switch
‹ T5-----8-pin console cable
‹ T6-----Elevation cable
‹ T7-----6-pin console cable
‹ T8----- Speed sensor line
‹ T9----- Ground wire
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
T9200/T9250 MCB WIRING(FOR 110V / 220V)
T2 T1
T9
T7
T8
T5
T6
T3 T4
VR1
‹ T1-----Motor wire (black)
‹ T2-----Motor wire (red)
‹ T3-----D1 of on/off switch
‹ T4-----D3 of on/off switch
‹ T5-----8-pin console cable
‹ T6-----Elevation cable
‹ T7-----6-pin console cable
‹ T8----- Speed sensor line
‹ T9----- Ground wire
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3
CONSOLE ENGINEERING MODE GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
T9700(TM51D/E) TREADMILLS (for Software Ver. 2.5)
Apply to :
1. VISION T9700/T9600 serise treadmail .
2. 2004 year T9700 serise treadmail.
3. 2004 year for ID
How to enter into the engineering mode?
1. Press & Hold both “ELEVATION UP”
and “SPEED DOWN” at the same time for
3-5 sec. Then, the dot vision display will
show “DGB1J
A564” and right display is
showϘ VERSION ”
2. Press the "ELEVATION" or "SPEED" to
selectyou want and press the "SELECT"
key enter.
Display show
CONFIGURE
DISPLAY TEST
BURN IN TEST
AUTO CAL
SPEED SENSOR
RS 232 TEST
HR TEST
function interpret
set the treadmill all parameter
console LED test mode
treadmill running test mode
Auto-calibration mode
speed sensor test mode
RS-232 test mode
HR test mode
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
KEY BEHALE FUNCTION
key name
SELECT
function
To Store up the parameter
SPEED UP
Add this show parameter of speed and elevation
Decrease this show parameter of speed and
elevation
SPEED DOWN
STOP
ELEVATION UP
ELEVATION DOWN
START
Press the STOP key for 3~5 sec will reset to sources
Add address
Decrease address
No function
CONFIGURE INCLUDE
ADDRESS
description
SOURCES MIN MAX
P0 MIN SPD
set the Low speed 0.5mph the PWM
set the 1/2 max speed 5mph the PWM
set the Max speed 10mph the PWM
set the incline slope
33
176
340
1
2
70
P1 1/2 MAX
100 270
200 511
P2 MAX SPD
P3 ELV SLP
1
255
P4 ELV ZERO
P5 ELV MAX
P6 T96-97HRT E
P6 T96-97HRT M
P6 T9700S E
set the low the altitude
66
25 150
150 235
set the high the altitude
213
4-mile , 0.5~12mph , 15% altitude
5-km ,1.0~19km/h , 15% altitude
6-mile , 0.5~12mph , 15% altitude
7-km ,1.0~19km/h , 15% altitude
P6 T9700S M
6
4
52
P6 T9700RUNNER E 8-mile , 0.5~12mph , 15% altitude
P6 T9700RUNNER M 9-km ,1.0~19km/h , 15% altitude
P6 T9700HRT E
P6 T9700HRT M
P7 MAX TIME
P8 WEIGHT
42-mile , 0.5~12mph , 15% altitude
52-km , 0.8~19km/h , 15% altitude
Max enforce time
99
150
0
15
99
Import User Weight
35 400
P9 OP HOURS
P10 OP DIST
P11 BELT
Accumulate time
0
0
6553.5
6553.5
10
Accumulate distance
0
set the Running belt depth(mm)
set the roller caliber(mm)
1.4
60
0
P12 ROLLER
60
60
Download from Www.Somanuals.com. All Manuals Search And Download.
P13 ELV DIR
P14 ELV ERRS
P15 SCROLL
P16 LUBE HRS
P17 CLEAN
P18 BRUSH
P19 EXIT
Change the incline altitude
255
0
0
0
1
0
0
0
255
1
Change the altitude error switch, 0=OFF, 1=ON
set the change display show letter speed
Accumulate the after one lube to now hour
Accumulate the after clean to now distance
Accumulate the change motor brush to now distance
Go away the engineer mode
7
255
0
0xffff
0xffff
0xffff
0
0
ʳ
ʳ
ʳ
Remarks:
1. After execute indicated service, please enter the engineer mode to press the
STOP keyfor 3~5 sec to renew of the P16 ,P17 or P18.
2. If you want to the clean accumulate time and distance, please press the
"ELEVATION UP and DOWN" for 5 sec of user mode.
Error code definition
Error
E4
E5
E6
E7
Definition
Incline motor parameter over the set
Incline motor not to movement
Incline motor the signal not answer
Speed over the 2.0 mph0km/h
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
T9600HRT(COMFORT)/T9600HRT/T9500HRT/T9450HRT/
T9350/T9300 TREADMILLS ( for Software Ver. 5.9)
Apply to :
1. VISION T9300/T9350/T9400/T9450/T9500 serise treadmail.
2. 2004 year T9300/T9350/T9450/T9500/T9600 serise treadmail.
3. 2004 year T9350/T9450/T9500 for ID
How to enter into the engineering mode?
1. Press & Hold both “ELEVATION UP”
and“SPEED DOWN” at the same time for3-5
sec. Then, the dot vision display will show
ϘDGAJ
n0nE” .
2. Press the "ELEVATION" or "SPEED" to
select
you want and press the "SELECT"
key enter.
Display show
ENG1
function interpret
set the treadmill all parameter
console LED test mode
treadmill running test mode
Auto-calibration mode
speed sensor test mode
come back the user mode
ENG2
ENG3
ENG4
ENG5
NONE
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
KEY BEHALE FUNCTION
key name
SELECT
SPEED UP
function
To Store up the parameter
Add this show parameter of speed
and elevation
SPEED DOWN
Decrease this show parameter of
speed and elevation
ELEVATION UP
ELEVATION DOWN
START
Add address
Decrease address
Enter P0~P14 parameter
ENG1
ADDRESS
DEFINITION
MIN SPD
SOURCES
SCOPE
P0
P1
P2
P3
P4
P5
P6
refer to
appendix(1)
refer to appendix(1)
MAX SPD
1/2 MAX SPD
ELV SLP
1
1~255
ELV ZERO
ELV MAX
refer to
appendix(1)
refer to appendix(1)
MODEL SET
Metric/ English
refer to
appendix(2)
P7
P8
MAX TIME
WEIGHT
99
15~99 min(Km/Mile
the same)
150LB(Mile)
68kg (Km)
35~400LB(Mile)
35~400kg(Km)
0~6553.5
P9
P10
OP HOURS (hr)
OP DIST
0
0
0~6553.5
(Mile/km)
BELT (mm)
ROLLER
ELV DIR
EXIT
P11
P12
P13
P14
5
0~10
60
0~255
60
255
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix (1)
SOU=SOURCES PARAMETER
SCO=SCOPE PARAMETER
MODEL Metric/ P6 P0
SOU SCO SOU SCO SOU SCO SOU SCO SOU SCO
P1
P2
P4
P5
English
English
SET
0
250~511
250~511
250~511
250~511
250~511
100~270
100~270
100~270
100~270
100~270
130~255
130~255
130~255
130~255
130~255
T9300
(TM55)
1~150
1~150
1~150
1~150
1~150
41 2~70 363
189
189
189
189
189
69
69
69
69
69
217
217
217
217
217
Metric
English
Metric
English
Metric
1
2
3
2
3
41
2~70 363
2~70 363
2~70 363
2~70 363
2~70 363
T9300HRT
(TM55D)
41
41
41
41
T9400HRT
(TM56)
250~511
100~270
130~255
1~150
189
69
217
250~511
250~511
250~511
100~270
100~270
100~270
130~255
130~255
130~255
T9350
(TM42)
1~150
1~150
1~150
1~150
English
Metric
4
5
41
41
2~70 363
2~70 363
2~70 363
2~70 363
189
189
189
189
66
66
66
66
220
220
220
220
English 22 41
Metric 32 41
250~511
100~270
130~255
250~511
250~511
250~511
100~270
100~270
100~270
130~255
130~255
130~255
T9350HRT
(TM42F)
1~150
1~150
1~150
English
Metric
English
6
7
6
41
41
41
2~70 363
2~70 363
2~70 363
189
189
189
66
66
66
220
220
220
T9450HRT
(TM47)
250~511
250~511
250~511
250~511
250~511
100~270
100~270
100~270
100~270
100~270
130~255
130~255
130~255
130~255
130~255
1~150
1~150
1~150
1~150
1~150
Metric
7
41
2~70 363
2~70 363
2~70 363
2~70 348
2~70 348
189
189
189
179
179
66
66
66
220
220
220
177
177
English 23 41
Metric 33 41
T9500HRT
(TM54)
English
English
8
8
29
29
63
63
T9500HRT
(TM54)
Download from Www.Somanuals.com. All Manuals Search And Download.
250~511
250~511
250~511
250~511
250~511
100~270
100~270
100~270
100~270
100~270
130~255
130~255
130~255
130~255
130~255
1~150
1~150
1~150
1~150
1~150
Metric
9
29
2~70 348
2~70 348
2~70 348
2~70 348
2~70 348
179
179
179
179
179
63
63
177
177
177
177
177
English 24 29
Metric 34 29
English 10 29
Metric 11 29
63
63
63
T9600HRT
(TM53)
Appendix (2)
Min.
Speed
Metric/ Configuration
Max.
Speed
Max
Grade
0%
Max
Grade
offset
5
Model
English
Number
Grade
offset
19
T9300
(TM55C)
English1
Metric1
0
1
2
3
0.5MIL
1.0KM
0.5MIL
1.0KM
10MIL
16KM
10MIL
16KM
12%
12%
12%
12%
19
19
19
5
5
5
T9400HRT English1
(TM56)
Metric1
T9350
English1 4 (For USA)
0.5MIL
10MIL
12%
5
5
(TM42C)
Metric1 5 (For USA)
1.0KM
0.5MIL
0.8KM
0.5MIL
1.0KM
16KM
10MIL
16KM
10MIL
16KM
12%
12%
12%
12%
12%
5
5
5
5
5
5
5
5
5
5
English2
Metric2
22(For ID)
32(For ID)
T9450HRT English1 6 (For USA)
(TM47C)
Metric1 7 (For USA)
English2
Metric2
23(For ID)
33(For ID)
0.5MIL
0.8KM
0.5MIL
10MIL
16KM
12MIL
12%
12%
12%
5
5
19
5
5
15
T9500HRT English1 8 (For USA)
(TM54C)
Metric1 9 (For USA)
1.0KM
19KM
12%
19
15
English2
Metric2
24(For ID)
34(For ID)
0.5MIL
0.8KM
12MIL
19KM
12%
12%
19
19
15
15
T9600HRT English1
10
11
0.5MIL
1.0KM
12MIL
19KM
15%
15%
13
13
15
15
(TM53D)
Metric1
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Remarks :
1. If set address P6 model is T9450(Configuration Number 6/7/23/33) machine the
address P11 will automatic set to 7,because running band the depth is 4.4mm.
2. If you want to the clean accumulate time and distance, please press the
"ELEVATION UP and DOWN" for 5 sec of user mode.
Error code definition
Error
Definition
E4
E5
E6
Incline motor parameter over the set
Incline motor not to movement
Incline motor the signal not answer
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
T9200/T9250 TREADMILLS ( for Software Ver. S706)
How to enter into the engineering mode?
1. Press & Hold both “ELEVATION UP” and
“SPEED DOWN” at the same time for3-5 sec.
Then, the dot vision display first will show
Ϙ VERSION ” follow showϘ ENG 1 ”
2. Press the "ELEVATION" or "SPEED" to
select you want and press the "START" key
enter.
Display show
ENG1
function interpret
set the treadmill all parameter
console LED test mode
treadmill running test mode
Auto-calibration mode
ENG2
ENG3
ENG4
KEY BEHALE FUNCTION
key name
STOP
function
Hold STOP key for 3 sec will Come
back to above mode
Add this show parameter of speed
and elevation
Decrease this show parameter of
speed and elevation
SPEED UP and ELEVATION UP
SPEED DOWN and ELEVATION
DOWN
START
To Store up the parameter
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG1
ADDRESS
DEFINITION
MIN SPD
SOURCES
450
SCOPE
210~3900
2000~3900
P0
P1
P2
P3
P4
P5
P6
P7
MAX SPD
No function
No function
ELV ZERO
ELV MAX
No function
MAX TIME
2000
30
245
1~255
1~255
99
5~99 min(Km/Mile
the same)
P8
WEIGHT
150LB(Mile)
68kg (Km)
35~400LB(Mile)
35~400kg(Km)
0~9999
P9
P10
OP HOURS (hr)
OP DIST
0
0
0~9999
(Mile/km)
Remarks:
1. If you want to the clean accumulate time and distance, please enter
engineering mode select “ENG1” enter, please enter P9 (Accumulate
Time) or P10 (Accumulate Distance) hold “ELEVATION DOWN and
SPEED UP” for 3~5 sec.
Error code definition
Error
E2
Definition
Incline motor problem
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4
MCB LED INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
MCB LED Indication
When we designed the lower control board (MCB) for our
treadmills we placed status lights (LEDs) on it to aid in field
diagnosis and repair. The following is an overview of what
these indicator lights mean and what can be checked with
them in the field.
Note:
Use a multi-meter
to test the power
socket.
110v mode:
95v Д 140v
220v mode:
210v Д 250v
Light- When lit, this indicates that the MCB
has power applied. If this LED is off, check
connections, power switch position, fuses and circuit
breakers. If the AC light is not lit, the MCB will not
operate.
Note:
For MCB
(Lower-board)
Light- When lit, this indicates the
presence of the unregulated 18 volt direct
current supply necessary for the operation of the MCB
circuitry. If dim the supply voltage may be marginal and if
out, not present or inadequate. If this light is not lit, the
MCB will not operate even if the PCB is operating properly.
If the AC light is lit and the +11V and +18V light are not,
check fuse F1. If the +11V light is lit and the +18V light is
not lit, return the board to JMI.
Note: For PCB
(Upper-board)
Light- When lit, this indicates the
presence of the regulated 11 volt direct
current supply necessary for the operation of the PCB. If
dim the supply voltage may be marginal and if out not
present or inadequate. If the light is not lit, the console will
not operate. If the AC and +18V light are lit and the +11V
light is not, check for shorted cabling or a defective upper
console. If the AC light is lit and the +11V and +18V lights
are not, check fuse F1.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
MCB LED Indication
Light- When lit, indicates the High
Power Direct Current supply for the motor
(B+) is online. This light will remain lit for a period of time
after power has been removed from the MCB. While the
MTR light remains lit, anyone handling the MCB should
use caution since there is still a hazardous potential
present. When the MTR light is off, B+ is not present and
the motor controller will not operate. If the MTR and I-limit
lights are off, verify motor connections and proper motor
operation. If the MTR light is off and the I-limit light is on,
the MCB shut off due to an extended current limit condition.
In this case, resetting the PCB or cycling power will
eliminate the problem. However, the treadmill should be
thoroughly examined for wear or damaged components
which might have lead to the extended current limit
condition. If this problem persists, return the board to
JMI.
Note:
over 26 Amps when
lit
Light- When lit, indicates the current
4-
to the motor has reached the peak
current trip point of 26 Amps. The MCB will limit the
current when the current limit point has been reached. If
the current limit continues for roughly 5 seconds, the MCB
shuts down and the I-Limit light will remain on. To reset
the I-Limit, turn the treadmill off at the power switch wait
about 30 seconds then turn the power back on.
Light- Indicates the control PWM
Note:
a control command
from the PCB to the
MCB
from the PCB is present. It will blink at
the control frequency used by the PCB when the PCB
commands speed. If the control signal should exceed 95
percent duty cycle, the PWM light shuts off and sets the
MCB to a safe shutdown mode. In the event this should
occur, the power to the treadmill should be removed, the
cabling checked for shorts and the PCB replaced. If this
problem persists, replace the MCB.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
MCB LED Indication
Light- Indicates the PCB is commanding the
incline motor to move up. If the User is
commanding the incline to increase and this light is not lit,
check cabling, verify proper PCB operation and replace it
if either is defective. If the problem persists, replace the
MCB. If the light is lit but the incline is not moving, check
and verify incline motor and its connection to the board;
check fuse F2. If this problem persists replace MCB.
Note:
the incline is being
commanded up
Note:
the incline is being
commanded down
Light- Indicates the PCB is commanding the
incline motor to move down. If the User is
commanding the incline to decrease and this light is not lit,
check cabling, verify proper PCB operation and replace it
if either is defective. If the problem persists, replace the
MCB. If the light is lit but the incline is not moving, check
and verify incline motor and its connection to the board;
check fuse F2. If this problem persists replace MCB.
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
PWM MCB LED CHART
NO. AC +18V +11V MTR I-LIMIT
PWM
OFF
OFF
OFF
OFF
UP
OFF
OFF
OFF
OFF
N/A
DN
OFF
OFF
OFF
OFF
N/A
OFF OFF OFF OFF
OFF
OFF
OFF
OFF
OFF
ON
1
2
3
4
5
6
7
ON
ON
ON
ON
ON
ON
OFF OFF OFF
ON
OFF
ON
ON
ON
OFF ON
ON OFF
ON OFF
OFF OR
BLINKING
DIM/
ON
BLINKING
N/A
N/A
OFF
ON ON
ON ON
ON
BLINKING
N/A
N/A
COMES ON
BRIEFLY &
THEN SHUTS
OFF
ON
ON
OFF
N/A
N/A
8
ON
ON
ON
ON
ON ON
ON ON
OFF
OFF
N/A
ON
OFF
ON
9
N/A
OFF
10
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
MCB LED-AIDED TROUBLESHOOTING CHART
NO.
1
PROBLEM/RESULT
CORRECTIVE ACTION
Verify connections, power switch, circuit
breaker and fuse
No operation of MCB or PCB
No operation of MCB or PCB Check fuse F1
2
3
PCB will not power up
Replace MCB
Verify adequate line voltage. If line voltage is
adequate, MCB is damaged and needs to be
returned to manufacturer.
PCB will power up but the MCB
will not operate
4
Verify connections to motor and the motor
itself. If the motor and its connections are
good, the MCB should be replace. Return
MCB to manufacture with information on
location. Power level, how it was used when
failure occurred etc.
The motor can be verified by disconnection
the motor; connecting a volt-ohm meter(set to
VCD) to the motor leads; and spinning the
tread and observing a voltage. If no voltage,
Bad motor.
A 5-second current limit time-out has occurred.
Resets console or cycle power to correct.
Check treadmill for excessive wear or
mechanical defects. If problem persists, return
MCB.
Will not operate the motor
Will not operate the motor
5
6
The MCB is experiencing a discontinuous over
current events. Check for mechanical wear
and/or defective motor. If on mechanical wear
and motor good, replace MCB and return
defective MCB to manufacturer.
Check and verify the J2 and J3 cables are
good, replace the PCB. If the problem
persists, replace the MCB.
MCB in current limit mode
Will not operate the motor
7
8
Verify connections to the J3 & incline motor. If
the connections look good, check F2.
Verify connections to the J3 & incline motor. If
the connections look good, check F2.
Incline does not move
Incline does not move
9
10
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5
TROUBLESHOOTINGS
Download from Www.Somanuals.com. All Manuals Search And Download.
No display on console
Possible causes:
1. Breaker is damaged.
2. ON/OFF switch is damaged.
3. MCB is damaged.
4. 6-pin console cable is damaged.
5. PCB is damaged.
Fix:
1. ( refer to “MCB LED layout & indication”……SECTION 6)
Verify if LED 115vAC(AC) is lit. If this LED is lit, go to step 2.
If LED 115vAC(AC) is not lit, verify the following:
© Inspect the circuit breaker to see
if it has tripped off.
A
B
( If it is tripped off….like diagram B,
reset the breaker. And check which
part is short-circuited. Then replace
the short-circuited part.)
2. The switch is turned to the "ON" position.
( If the switch light isn't lit, replace the switch.)
©Verify wire connection AC1 & AC2 on the MCB.
( refer to “wiring diagram”…….page 4-3 )
©Verify the ON/OFF switch, breaker & socket wires are connected.
3. Verify if LED +11v & +18v is lit.
If one is not lit, replace MCB.
4.Replace console cable.
5. Replace PCB.
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Running speed is not stable
Possible causes:
1. AC power voltage is too low.
2. Tension of drive belt or running belt is too loose.
3. Poor adjustment of MCB.
4. MCB is damaged.
5. Motor is damaged.
Fix:
1. Check the power voltage by using voltage-meter to see if it is within 120V
̈́15% or 230V̈́15%.
© If the power voltage isn't within the range, look for a qualified
electrician for help.
2. Open the motor cover, if the belt has stretched and is slipping across the
rollers when running.
© Adjust the belt tension.
3. Remove the motor cover and run the
machine at low speed, then adjust the IR
COMP of MCB.
© If it hasn't been improved, replace new
MCB.
4. Replace new motor.
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Treadmill starts to run by itself
Possible causes:
1. The console cable is broken.
2. PCB is out of order.
3. MCB is out of order.
Fix:
1.Replace the console cable with a new one.
2.Replace the PCB.
3.Replace the MCB.
All or some of the keys on console do not work
Possible causes:
1. Keypad connecting plug is not fit-in properly.
2. Keypad is damaged.
3. PCB is damaged.
Fix:
1. Disconnect the keypad and replace the keypad, and check again.
2. Replace the keypad.
3. Replace the PCB.
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Noises generated under motor cover
Possible causes:
1.The running belt tension is adjusted too tight.
2.The bearing of front roller is not installed correctly.
3.Dirty grooves of drive belt.
4.The motor is damaged.
Fix:
1. Adjust the belt tension so
that the belt does not
start slipping and then
check if the noise has
disappeared.
© Let the treadmill run,
without using it, for at
least 5 days because
sometimes the bearing
will settle and become
quiet then check if the
noise has disappeared.
2. Replace the front roller with a new one to see if the noise disappear.
3. Remove drive-belt and check the grooves in belt for dirt or dust and clean
if necessary. Clean also the motor pulley and the roller pulley grooves
and check if the noise has disappeared.
4. The motor bearing is damaged.
(Refer to "motor bearings replacement procedure"……page 8-22 ~
8-23)
© Replace the motor.
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Treadmill will not start
Possible causes:
1. MCB is damaged.
2. 8-pin console cable is damaged.
3. PCB is damaged.
4. Motor is damaged.
Fix:
Open motor cover, verify wire connection MTR1 and MTR2 on the MCB then
plug in the power cord and turn on the power switch. Then press
“START“ button.
Please check below item:
1. Verify the LED indicator of MTR is lit.
(
If that LED MTR is not lit, replace MCB.)
2. Verify if LED PWM is lit.
(if it is not lit, replace 8-pin console cable.)
3. If LED PWM is still not lit, replace PCB.
4. Replace Motor.
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Incline function does not work
Possible causes:
1. The 8-pin console cable is damaged.
2. Incline motor is damaged.
3. PCB is damaged.
4. MCB is damaged.
5. The incline setting is not correct.
Fix:
© Enter to the Engineering Mode to recalibrate the elevation values
Then press "FAST" and "SLOW" key to see if the incline motor will be
activated.
1. OR
Use a new 8-pin console cable to connect PCB and MCB. Then press
"FAST" and "SLOW" key to see if the incline motor will be activated.
2. OR
Replace the incline motor.
3. OR
Replace PCB.
4. OR
Replace MCB.
5. Enter Engineering Mode to renew the Auto-calibration mode elevation
parameter.
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Heart-Rate-Control function does not work
Possible causes:
1. Transmitter does not contact with user's chest very well.
2. Transmitter(Polar-belt) is at low battery status.
3. Transmitter(Polar-belt) is damaged.
4. Heart-rate-control board is damaged.
5. PCB is damaged.
Fix:
1. Center the transmitter on your chest below the pectoral muscle(breast)
as shown, then check again.
2. Remove the battery cover of the transmitter. Replace a new battery and
check again.
© Actually, as moisture may activate the transmitter, please dry
transmitter after use.
3. OR Transmitter is damaged. Replace the Transmitter.
4. OR
board.
5. OR
Heart-rate-control board is damaged. Replace the HR-control
PCB is damaged. Replace the PCB.
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages on the Console
T9700 (TM51D/E) Error code definition
Error
E4
E5
E6
E7
Definition
Incline motor parameter over the set
Incline motor not to movement
Incline motor the signal not answer
Speed over the 2.0 mph0km/h
Error Message "E4" : Please enter the engineer mode to execute the
AUTO-CAL MODE.
Error Message "E5" : 1. Please check the incline motor cable whether to
inset MCB.
2. Check the console signal whether transmission to
MCB, you can refer to MCB LED UP and DOWN. If
LED not light please check the console cable and
console. If LED have light please replace the
incline motor.
Error Message " E6" : 1. Please check the incline motor cable whether to
inset MCB.
2. Replace the incline motor
Error Message " E7" : Please enter the engineer mode to execute the
AUTO-CAL MODE.
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
T9600HRT (COMFORT)/T9600HRT/T9500HRT/T9450HRT/T9350/T9300
Error code definition
Error
E4
E5
Definition
Incline motor parameter over the set
Incline motor not to movement
Incline motor the signal not answer
E6
TROUBLESHOOTINGS
Error Message " E4" : Please enter the engineer mode to execute the AUTO-CAL
MODE
Error Message " E5" : 1. Please check the incline motor cable whether to inset
MCB.
2. Check the console signal whether transmission to MCB,
you can refer to MCB LED UP and DOWN. If LED not
light please check the console cable and console. If LED
have light please replace the incline motor
Error Message " E6" : 1. Please check the incline motor cable whether to inset
MCB.
2. Replace the incline motor
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
T9200/T9250 Error code definition
Error code definition
Error
E2
Definition
Incline motor problem
Error Message " E2" :
1. Please check the incline motor cable whether to inset MCB.
2. Check the console signal whether transmission to MCB, you can refer to
MCB LED UP and DOWN. If LED not light please check the console
cable and console. If LED have light please replace the incline motor
3. Please enter the engineer mode to execute the AUTO-CAL MODE
5-10
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6
SOFTWARE UPGRADE PROCEDURE
Revision: 1.0
Date: 1999-09-01
Download from Www.Somanuals.com. All Manuals Search And Download.
VISION SERIES TREADMILL SOFTWARE UPGRADE SOP
A. Service Tools & Accessories:
1.
2.
3.
Computer (Notebook is preferred)
Connection cables ( Parts NO: MQMXCV001 and MQMXCV002)
Software
6-1
Revision: 1.0
Date: 1999-09-01
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Steps:
2. Connection cables & short pin is ready.
3. Turn ON the power switch.
4. Find out the software version file in the computer and then actuate/open the file by “click”
the mouse twice.
5. The computer will be turned into DOS mode, and run the installation work. Automatically.
(It takes around 2 minutes for installation.)
6. After competed installation, the computer will show passing on the computer screen.
7. Turn OFF the power switch.
8. Disconnect the cables.
9. Turn ON the power switch and then enter into the engineering mode to confirm if the
software
had been installed/upgraded.
6-2
Revision: 1.0
Date: 1999-09-01
Download from Www.Somanuals.com. All Manuals Search And Download.
|