EX7000 SERIES
MICROWAVE SWITCH ASSEMBLIES WITH
LXI-COMPLIANT LAN INTERFACE
USER’S MANUAL
P/N: 82-0121-000
Release December 14, 2007
VXI Technology, Inc.
2031 Main Street
Irvine, CA 92614-6509
(949) 955-1894
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
INTRODUCTION
Certification..........................................................................................................................................................5
Warranty...............................................................................................................................................................5
Limitation of Warranty.........................................................................................................................................5
Restricted Rights Legend......................................................................................................................................5
DECLARATION OF CONFORMITY...............................................................................................................................6
GENERAL SAFETY INSTRUCTIONS.............................................................................................................................7
Terms and Symbols ..............................................................................................................................................7
SUPPORT RESOURCES ...............................................................................................................................................8
SECTION 1....................................................................................................................................................................9
INTRODUCTION .........................................................................................................................................................9
Introduction ..........................................................................................................................................................9
EX71HD: High-Density 26 GHz Modular Microwave Switching, Non-Latching .........................................9
EX72SF: High-Density 26 GHz Modular Microwave Switching, Latch with Self-Terminating Options....10
EX7400: LXI Based Custom RF Interface Platform.....................................................................................10
Common Features...............................................................................................................................................10
Interactive Control..............................................................................................................................................11
Relay Drive Control............................................................................................................................................12
Interfacing with Other Components ...................................................................................................................13
Features...............................................................................................................................................................13
Relay Odometer.............................................................................................................................................13
Exclude Lists.................................................................................................................................................13
Scan Lists ......................................................................................................................................................13
Configuration Table ......................................................................................................................................13
Programmable MBB and BBM.....................................................................................................................13
EX7000 Specifications .......................................................................................................................................14
SECTION 2..................................................................................................................................................................15
PREPARATION FOR USE...........................................................................................................................................15
Overview ............................................................................................................................................................15
Unpacking...........................................................................................................................................................15
Installation Location...........................................................................................................................................15
Driver Installation...............................................................................................................................................16
EX7000 Hardware Setup ....................................................................................................................................16
Network Configuration.......................................................................................................................................16
SECTION 3..................................................................................................................................................................19
BASIC OPERATION ..................................................................................................................................................19
Introduction ........................................................................................................................................................19
Rear Panel View .................................................................................................................................................19
Trigger Bus Connectors.................................................................................................................................20
Digital I/O Connector....................................................................................................................................20
General Purpose I/O......................................................................................................................................21
Reset Button..................................................................................................................................................22
Front Panel View................................................................................................................................................22
EX71HD........................................................................................................................................................22
EX72SF.........................................................................................................................................................23
EX7400 .........................................................................................................................................................24
SECTION 4..................................................................................................................................................................25
WEB PAGE OPERATION...........................................................................................................................................25
Introduction ........................................................................................................................................................25
General Web Page Operation .............................................................................................................................25
Password Protection ......................................................................................................................................26
EX7000 Series Preface
3
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
VXI Technology Logo ..................................................................................................................................27
EX7000 Title Block ......................................................................................................................................27
Soft Front Panel..................................................................................................................................................28
Network Configuration.......................................................................................................................................29
Time Configuration ............................................................................................................................................31
Device Identify ...................................................................................................................................................33
Upgrade ..............................................................................................................................................................33
Reset ...................................................................................................................................................................34
Reboot.................................................................................................................................................................34
SECTION 5..................................................................................................................................................................35
THEORY OF OPERATION..........................................................................................................................................35
Introduction ........................................................................................................................................................35
System Overview................................................................................................................................................35
Open-Collector vs. TTL Drive Lines..................................................................................................................36
Relay Access & Control .....................................................................................................................................37
Continuous Mode..........................................................................................................................................37
Pulse Mode....................................................................................................................................................38
INDEX.........................................................................................................................................................................39
4
EX7000 Series Preface
Download from Www.Somanuals.com. All Manuals Search And Download.
CERTIFICATION
VTI Microwave, a business unit of VXI Technology, Inc. (VTI) certifies that this product met its published
specifications at the time of shipment from the factory. VTI Microwave further certifies that its calibration
measurements are traceable to the United States National Institute of Standards and Technology (formerly National
Bureau of Standards), to the extent allowed by that organization’s calibration facility, and to the calibration facilities
of other International Standards Organization members.
WARRANTY
The product referred to herein is warranted against defects in material and workmanship for a period of one year
from the receipt date of the product at customer’s facility. The sole and exclusive remedy for breach of any warranty
concerning these goods shall be repair or replacement of defective parts, or a refund of the purchase price, to be
determined at the option of VTI Microwave.
For warranty service or repair, this product must be returned to a VXI Technology authorized service center. The
product shall be shipped prepaid to VTI and VTI shall prepay all returns of the product to the buyer. However, the
buyer shall pay all shipping charges, duties, and taxes for products returned to VTI from another country.
VTI Microwave warrants that its software and firmware designated by VTI Microwave for use with a product will
execute its programming when properly installed on that product. VTI Microwave does not however warrant that the
operation of the product, or software, or firmware will be uninterrupted or error free.
LIMITATION OF WARRANTY
The warranty shall not apply to defects resulting from improper or inadequate maintenance by the buyer, buyer-
supplied products or interfacing, unauthorized modification or misuse, operation outside the environmental
specifications for the product, or improper site preparation or maintenance.
VTI Microwave and VXI Technology, Inc. shall not be liable for injury to property other than the goods themselves.
Other than the limited warranty stated above, VXI Technology, Inc. makes no other warranties, express or implied,
with respect to the quality of product beyond the description of the goods on the face of the contract.
VTI Microwave specifically disclaims the implied warranties of merchantability and fitness for a particular purpose.
RESTRICTED RIGHTS LEGEND
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subdivision (b)(3)(ii) of the
Rights in Technical Data and Computer Software clause in DFARS 252.227-7013.
VTI Microwave
A VXI Technology, Inc. Business Unit
2031 Main Street
Irvine, CA 92614-6509 U.S.A.
EX7000 Series Preface
5
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
D E C L A R A T I O N O F C O N F O R M I T Y
Declaration of Conformity According to ISO/IEC Guide 22 and EN 45014
MANUFACTURER’S NAME
VXI Technology, Inc.
MANUFACTURER’S ADDRESS
2031 Main Street
Irvine, California 92614-6509
PRODUCT NAME
Microwave Switch Assembly with LAN Interface
MODEL NUMBER(S)
PRODUCT OPTIONS
PRODUCT CONFIGURATIONS
EX7000 Series Microwave Switch Assemblies
All
All
VXI Technology, Inc. declares that the aforementioned product conforms to the requirements of
the Low Voltage Directive 73/23/EEC and the EMC Directive 89/366/EEC (inclusive 93/68/EEC)
and carries the “CE” mark accordingly. The product has been designed and manufactured
according to the following specifications:
SAFETY
EN61010 (2001)
EMC
EN61326 (1997 w/A1:98) Class A
CISPR 22 (1997) Class A
VCCI (April 2000) Class A
ICES-003 Class A (ANSI C63.4 1992)
AS/NZS 3548 (w/A1 & A2:97) Class A
FCC Part 15 Subpart B Class A
EN 61010-1:2001
I hereby declare that the aforementioned product has been designed to be in compliance with the relevant sections
of the specifications listed above as well as complying with all essential requirements of the Low Voltage Directive.
December 2007
Steve Mauga, QA Manager
6
EX7000 Series Preface
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY INSTRUCTIONS
Review the following safety precautions to avoid bodily injury and/or damage to the product.
These precautions must be observed during all phases of operation or service of this product.
Failure to comply with these precautions, or with specific warnings elsewhere in this manual,
violates safety standards of design, manufacture, and intended use of the product.
Service should only be performed by qualified personnel.
TERMS AND SYMBOLS
These terms may appear in this manual:
Indicates that a procedure or condition may cause bodily injury or death.
WARNING
CAUTION
Indicates that a procedure or condition could possibly cause damage to
equipment or loss of data.
These symbols may appear on the product:
ATTENTION - Important safety instructions
Frame or chassis ground
Indicates that the product was manufactured after August 13, 2005. This mark is
placed in accordance with EN 50419, Marking of electrical and electronic
equipment in accordance with Article 11(2) of Directive 2002/96/EC (WEEE).
End-of-life product can be returned to VTI by obtaining an RMA number. Fees
for take-back and recycling will apply if not prohibited by national law.
WARNINGS
Follow these precautions to avoid injury or damage to the product:
To avoid electrical overload, electric shock, or fire hazard, do not
use a power source that applies other than the specified voltage.
To avoid injury, electric shock or fire hazard:
Use Proper Power Source
Operating Conditions
-
-
-
-
Do not operate in wet or damp conditions.
Do not operate in an explosive atmosphere.
Operate or store only in specified temperature range.
Provide proper clearance for product ventilation to prevent
overheating.
-
DO NOT operate if any damage to this product is suspected.
Product should be inspected or serviced only by qualified
personnel.
The operator of this instrument is advised that if the equipment is
used in a manner not specified in this manual, the protection
provided by the equipment may be impaired.
Improper Use
Conformity is checked by inspection.
EX7000 Series Preface
7
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
SUPPORT RESOURCES
Support resources for this product are available on the Internet and at VXI Technology customer
support centers.
VTI Microwave
A VXI Technology Business Unit
World Headquarters
VXI Technology, Inc.
2031 Main Street
Irvine, CA 92614-6509
Phone: (949) 955-1894
Fax: (949) 955-3041
VXI Technology
Cleveland Instrument Division
5425 Warner Road
Suite 13
Valley View, OH 44125
Phone: (216) 447-8950
Fax: (216) 447-8951
VXI Technology
Lake Stevens Instrument Division
VXI Technology, Inc.
1924 - 203 Bickford
Snohomish, WA 98290
Phone: (425) 212-2285
Fax: (425) 212-2289
Technical Support
Phone: (949) 955-1894
Fax: (949) 955-3041
E-mail: [email protected]
8
EX7000 Series Preface
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1
INTRODUCTION
INTRODUCTION
The EX7000 series of modular microwave switch assemblies consist of standard products as well
as custom factory configured enclosures. All are rack mountable and range in size from 1U to 4U.
The standard products include the EX71HD, a 1U high-density, 26 GHz non-latching microwave
switch mainframe; the EX72SF, a 2U high-density, 26 GHz latching microwave switch
mainframe; and the EX7400, a 4U switching platform that is custom built per customer
specifications, but contains the same LAN interface, relay driver boards, and power supply as the
EX71HD and EX72SF. The EX7400 can contain an assortment of electromechanical relays, plus
any additional active or passive components that may be required. Every member of the EX7000
series comes with an LXI compliant LAN interface.
EX71HD: High-Density 26 GHz Modular Microwave Switching, Non-Latching
FIGURE 1-1: EX71HD (SHOWN WITH A FULL COMPLIMENT OF HIGH-DENSITY SWITCHES)
The EX71HD measures only 1U (1.75”) in height yet is configured for a family of miniature
microwave switches and contains twelve front panel slots that can be configured with any of the
following switches in any order desired:
7102
7104
7106
7122
Dual SPDT
SP4T
SP6T
Transfer
The unit can be delivered preconfigured from the factory with any twelve of the above devices or
can be purchased with less than the full compliment of switches. Additional switches can be added
by the customer at later dates. The EX71HD is a totally self contained unit with EX7000-OEM
board set and ac power supply built in to the assembly.
EX7000 Series Introduction
9
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
EX72SF: High-Density 26 GHz Modular Microwave Switching, Latch with Self-Terminating
Options
FIGURE 1-2: EX72SF (SHOWN WITH A FULL COMPLIMENT OF AGILENT SWITCHES)
The EX72SF is a 2U (3.5”) enclosure that can house up to six Agilent SPDT switches as well as
up to six full-size Agilent multi-pole single throw latching terminated or unterminated switches. It
can be delivered preconfigured from the factory with twelve switches or can be purchased with
less than the full compliment of switches. Additional switches can be added by the customer at
later dates. The EX72SF is totally self contained unit with EX7000-OEM board set and ac power
supply built into the assembly. Also provided on the EX72SF is a 32-channel, general purpose I/O
bus. Access to this bus is through a front panel-mounted 37-pin D-sub connector. Further details
on this bus can be found in Section 3.
See Section 3, Basic Operation, for a complete list of Agilent switch modules that can be used
with the EX72SF.
EX7400: LXI Based Custom RF Interface Platform
The EX7400 is built around the same internal components as the EX71HD and EX72SF. It starts
life as a 4U high and 24” deep rack mountable enclosure. It can be purchased in this configuration
allowing a customer to add their own RF and microwave components to the front and rear panels
as well as the removable mezzanine that is located at approximately the mid way point between
the top and bottom covers. It may also be supplied as a custom or special unit which is
preconfigured at the factory with all of the components and inter-connect cabling specified by the
customer.
COMMON FEATURES
Preconfigured units, whether an EX71HD, EX72SF, or the EX7400, are delivered with a complete
Configuration File that contains all the pertinent details about each programmable device mounted
inside. In the case of the EX7400, which may contain internal inter-connect path cabling, the
Configuration File also contains all of the point-to-point signal path information. The information
included in the Configuration File allows the user to establish a complete signal route by
indicating only the end points in a compliant IVI-Switch Connect statement, thus simplifying the
programming task.
The EX7000 series assemblies, referred to here after as EX7000, consists of an LXI Class A
compliant digital controller interface, one or more 72-channel relay driver board, integral ac power
supply, and a selectable assortment of electromechanical microwave switches. More than one
relay driver boards are used in custom applications where the internal number of coils exceeds the
72 coil capacity of one relay driver board. As many as four relay driver boards, one plus three
10
EX7000 Series Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
expansion boards, are available for large designs. Extremely large designs, that require five to
eight relay driver boards, can be accommodated with special HW and SW updates. Consult the
factory for details.
FIGURE 1-3: POPULATED EX7400 MAINFRAME
NOTE
The EX7000 series assemblies, including the EX71HD, EX72SF, and EX7400 may be referred to
in this manual as simply EX7000
INTERACTIVE CONTROL
As an LXI-compliant device, the EX7000 has an embedded web server running which provides a
JAVA applet for interactively configuring the box for its specific configuration as well as allowing
for the direct control of components.
A functional list of the actual components within the enclosure is stored on-board in non-volatile
memory. Opening of the Soft Front Panel (SFP) results in a graphical depiction of the various
switching components along with an indication of the current state of their contacts. Simple mouse
clicks on the web browser can easily and quickly open and close any contact.
The embedded configuration file can be edited using a simple SW tool called the Configurator.
This is especially convenient when additional microwave switches are added in the field.
EX7000 Series Introduction
11
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
FIGURE 1-4: JAVA-BASED GRAPHICAL USER INTERFACE
RELAY DRIVE CONTROL
The EX7000 contains a proprietary circuit board set consisting of a Relay Driver Board (RDB)and
LXI LAN Interface Board, which is known as the EX7000-OEM when supplied as a set without
an enclosure. They have been designed to provide maximum flexibility for controlling virtually
any type of RF/microwave relay or component. Each RDB provides 72 high-current drivers,
which are divided into twelve sections of six lines. Each section consists of:
•
•
•
•
•
•
•
six high-current drive lines
six indicator/status bits
one reset line
four relay ID bits
one relay power input
one 5 V input
one ground
Each driver board is capable of recognizing and controlling either latching or non-latching switch
modules. A programmable delay (per driver board) dictates the amount of time allocated to relay
settling times and current cutoffs (for latching relays).
Each driver board has a single programmable delay parameter. The programmable delay for any
board should be set to the maximum value required by any component connected to that board.
12
EX7000 Series Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Data is latched to the gate of the output coil drive FET dictating whether or not the FET will sink
current and energize the relay coil. See the EX7000-OEM Manual (P/N: 82-0118-000) for more
details.
INTERFACING WITH OTHER COMPONENTS
The EX7000 board set is capable of controlling other programmable components, such as filters
and attenuators, through either the high-current channels or the 32-bit parallel I/O. Access to the
control lines can be achieved in various ways. The high-current channels are available from the
EX71HD and EX72SDF via pass-through switches that mount on the front panel in place of one
or more switches. These switches consist of a flat mounting plate with mounting holes to match
the multi-throw switch it replaces. A multi-pin connector is mounted to the plate and the connector
is wired directly to one of the relay driving connectors, allowing external use by the user.
In addition to the high-current control lines, the EX72SF also has a front panel mounted,
32-channel, TTL-level, general purpose IO bus available. Refer to Section 3 for details or obtain a
copy of the EX7000-OEM Manual for more information on this bus. Contact the factor or visit the
VXI Technology, Inc. website for a copy of this document.
FEATURES
Relay Odometer
Each relay drive line has an associated “odometer” which tracks the number of times a relay coil
has been actuated. This data is written to non-volatile memory and can be called from application
code or the web interface. This assists preventative maintenance programs as relays can be closely
monitored as they near end-of-life.
Exclude Lists
The supplied API supports the implementation of exclude lists. Undesirable combinations of relay
closures can be stored and warnings or errors will be generated any time an excluded combination
is attempted. This helps prevent unsafe conditions such as shorting sources to ground or coupling
one source to another.
Scan Lists
Up to 16,000 scan list elements can be stored to help reduce overhead that can be accrued when
relying on the host controller to manage the sequencing of switch states. A predefined list of
switch states can be stored on-board and advanced through hardware control/handshaking with
external system devices via the LXI Trigger Bus or the GP digital I/O port. Use of scan lists can
considerably speed up test execution times.
Configuration Table
The information included in the Configuration File allows the user to establish a complete signal
route by indicating only the end points in a compliant IVI-Switch Connect statement, thus
simplifying the programming task
Programmable MBB and BBM
The application code can globally define whether or not the relays ‘break-before-make’ or ‘make-
before-break’ when sequencing through relay setups.
EX7000 Series Introduction
13
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
EX7000 SPECIFICATIONS
GENERAL SPECIFICATIONS
PHYSICAL DIMENSIONS
EX71HD
EX72SF
19” (48.2 cm) width x 24.25” (61.6 cm) depth* x 1.75” (4.5 cm) height
19” (48.2 cm) width x 24.25” (61.6 cm) depth* x 3.50” (8.9 cm) height
19” (48.2 cm) width x 24.25” (61.6 cm) depth* x 7.0” (17.8 cm) height
* excludes coaxial connector protrusion from face of front and/or rear panels
EX7400
CONNECTORS
Host interface
Trigger bus
RJ-45 (CAT 5e) Ethernet (10/100T)
Dual 25-pin mini D-sub
8 LVDS in/out, LXI Class A
9-pin D-sub
GP digital I/O
8 TTL I/O
IEC EN 60320 C13
AC power
RESET
Momentary push-button LAN reset, available through rear panel access hole
POWER
Voltage
Power
90 V ac - 264 V ac, 47 Hz - 63 Hz
110 VA Max (EX71HD), 20 VA Max (EX72SF)
DIGITAL CONTROLLER BOARD (DCB)
MCF5272
PROCESSOR
32 MB
8 MB
SDRAM
Flash ROM
< 3 ms
Single-command response time
RELAY DRIVER BOARD (RDB)
RELAY POWER
+5 V to +48 V
*Three power pins, each connected to four relay driver connections
RELAY DRIVERS
72 open-drain high-current sink on a standard board. Options available to replace some or
all of the open drain outputs with TTL drivers. Expandable to 576. Twelve open-drain
very high-current sink drivers for reset. Arranged as one drive line per relay driver
connector as well as 12 lines together on one connector on J21.
MAXIMUM CURRENT SINK
200 mA (all channels ON) for 72 channels
410 mA (individual channels) for 72 channels
800 mA for 12 reset lines
TTL I/O
32 channels per board, expandable to 256
MODULE ID
Rotary switch (0 through 7 identifies driver board in chain)
SOFTWARE
PROGRAMMATIC CONTROL
IVI-COM and IVI-C API
IVI similar API for Linux
DOS-based interactive command set
INTERACTIVE CONTROL
CONFIGURATION TABLE
SCAN LIST
Embedded JAVA applet
128 elements (power-on, last known, user-defined)
16k set-ups
14
EX7000 Series Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2
PREPARATION FOR USE
OVERVIEW
This section provides a step-by-step process for setting up the EX7000 series assemblies for use.
For simplicity, the EX7000 series assemblies, including the EX71HD, EX72SF, and EX7400 will
be referred to as EX7000 in this section. It covers hardware installation, input connections, and
software installation.
UNPACKING
When the EX7000 is unpacked from its shipping carton, the contents should include the following
items:
•
•
•
•
•
EX71HD, EX72SF, or EX7400
EX7000 Series User’s Manual (this manual)
VTEX Switch Driver Programmer’s Manual
VXI Technology, Inc. Drivers and Product Manuals CD
Power line cord
All components should be immediately inspected for damage upon receipt of the unit.
INSTALLATION LOCATION
The EX7000 is designed to be largely insensitive to external electrical, magnetic, and thermal
disturbances. However, as with all precision instrumentation, certain precautions, if taken into
consideration, can help achieve maximum performance.
1) The unit should be located away from sources of extreme high or low temperatures.
2) The unit should be located away from sources of high magnetic fields such as motors,
generators, and power transformers.
The EX71HD and EX72SF employ active cooling for maximum product reliability. The EX7400
may or may not employ such cooling, depending on the expected power consumption. When any
of the EX7000 family of products is installed into a test fixture, the user must ensure that adequate
air flow is provided to all components.
EX7000 Series Preparation for Use
15
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
DRIVER INSTALLATION
The EX7000 is shipped with a VXI Technology, Inc. LXI Drivers and Product Manuals CD which
includes software drivers, user’s manuals, the VXI Technology Product Catalog, as well as some
third-party software. Please refer to the ReadMe.txt file included on the Distribution CD for
installation instructions specific to revision of the CD provided.
EX7000 HARDWARE SETUP
To properly set up the EX7000 for use, the following cabling connections must be made:
•
•
ac power cord, supplied with the EX7000 must be plugged into any standard ac outlet
providing 90 V ac to 264 V ac at 47 Hz to 63 Hz.
A connection between the Host PC and the EX7000 LAN port must be made. A CAT-5e
cable may be used to make this connection. Note, this cable is not provided with the EX7000.
FIGURE 2-1: EX7000 CABLING DIAGRAM
NETWORK CONFIGURATION
With its default network configuration, the EX7000 will attempt to locate a DHCP server. If one is
found, the IP address assigned by the DHCP server will be used. Otherwise, after a timeout of
20 seconds, the unit will attempt to obtain an IP address by using AutoIP.
NOTE
At any time, the EX7000 can be returned to a known, default network configuration by using the
LCI (LAN Configuration Initialize) mechanism. See Reset Button for more information.
AutoIP is a mechanism for finding an unused IP address in the range 169.254.X.Y, where X is in
the range 1 through 254 and Y is in the range 0 through 255. The device will first attempt to obtain
the specific address 169.254.X.Y, where X and Y are the second-to-last and last octets (bytes) of
the device’s MAC address. However, X will be set to 1 if it is 0 in the MAC address, and to 254 if
it is 255 in the MAC address. This is in accordance with the AutoIP standard (RFC 3927). If this
address is already in use, the unit will attempt to obtain other IP addresses in a pseudorandom
fashion until it finds one that is available.
16
EX7000 Series Preparation for Use
Download from Www.Somanuals.com. All Manuals Search And Download.
To illustrate the AutoIP mechanism, Table 2-1 lists the AutoIP default address for some example
MAC addresses.
MAC Address
00:0D:3F:01:00:01
00:0D:3F:01:01:01
00:0D:3F:01:A3:28
00:0D:3F:01:FE:FE
00:0D:3F:01:FF:FE
AutoIP Default Address
169.254.1.1
169.254.1.1
169.254.163.40
169.254.254.254
169.254.254.254
TABLE 2-1: AUTOIP DEFAULT ADDRESS ASSIGNMENT
If a static IP address assignment is preferred, one can be optionally assigned via the embedded
web page interface. This is done by clicking the Network Configuration link, disabling DHCP
and AutoIP, enabling Static, and then assigning a static IP address, subnet mask, and gateway
address, and, optionally up to three DNS servers. For more information, see Network
Configuration in Section 4.
EX7000 Series Preparation for Use
17
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
18
EX7000 Series Preparation for Use
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3
BASIC OPERATION
INTRODUCTION
The EX7000 Series modular microwave switch assemblies require only ac power and a LAN
connection to a PC or network. The PC must have an Internet browser, such as Internet Explorer
or Firefox, installed. The imbedded web page in each EX7000 allows easy access and control of
the internal microwave components.
REAR PANEL VIEW
The rear panel of the EX7000 contains an ac power entry module, an ac power switch, an Ethernet
10/100 Base-T connection, a general purpose digital IO connections, LXI trigger bus connectors,
and access to the reset button.
Figure 3-1 shows a typical rear panel, in this case, of an EX7400.
The rear panel of the EX7400 may have coaxial connectors. Their type, quantity, and location are
a function of the customer’s requirements.
FIGURE 3-1: EX7000 - TYPICAL REAR PANEL VIEW (EX7400)
EX7000 Series Basic Operation
19
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
Trigger Bus Connectors
The EX7000 provides an LXI compatible trigger bus connector set on the rear panel of the
instrument. Both connectors have the same pin assignments and are wired in parallel. For more
information on the LXI Trigger Bus and creating an appropriate cable, please visit
Terminator Specifications Rev 1.1. The trigger bus pin assignments are provided on the next page.
Trigger Bus Connectors
Pin
1
2
3
4
5
6
7
8
Signal
+3.3 V
GND
Pin
14
15
16
17
18
19
20
21
22
23
24
25
Signal
RP_TRIG_P0
RP_TRIG_N0
RESERVED
RP_TRIG_P2
RP_TRIG_N2
GND
RP_TRIG_P4
RP_TRIG_N4
GND
RP_TRIG_P1
RP_TRIG_N1
GND
RP_TRIG_P3
RP_TRIG_N3
GND
RP_TRIG_P5
RP_TRIG_N5
RESERVED
RP_TRIG_P7
9
RP_TRIG_P6
RP_TRIG_N6
RESERVED
10
11
12
13
RP_TRIG_N7
1
13
25
14
Digital I/O Connector
The EX7000 features an 8-channel digital I/O port on the rear panel of the instrument. This port
can be used as a trigger source and as a general purpose output device. The digital I/O connector is
a standard DB-9 with the following pin assignment:
Digital IO Connector
Pin
1
3
5
7
Signal
Pin
2
4
6
8
Signal
DIO Channel 0
DIO Channel 2
DIO Channel 4
DIO Channel 6
DIO Channel 1
DIO Channel 3
DIO Channel 5
DIO Channel 7
GND
9
1
5
6
9
Mating Connector: Tyco 5-747904-2
As a general purpose output device, each DIO channel can be independently programmed with
regards to its output functionality and its static level to assume when enabled as an output. When
not enabled as an output, a channel becomes tri-stated, preventing conflict with other potential
voltage drivers. Reference the port’s electrical specifications in Table 3-1 for voltage tolerance
limits and output drive capabilities. Regardless of output functionality, each channel provides
constant input functionality. That is, the input level on each channel can be accessed without a
specific enable command. Moreover, the base functionality of the DIO channels is not affected by
triggering, scanning, or any other instrument process.
20
EX7000 Series Basic Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
When enabled as an output, each channel also has the ability to generate a 1 µs pulse upon
command. An example application of this pulse is to use the EX7000 to externally trigger another
piece of test equipment. The specific operation of the pulse depends on the static level
programmed for that channel. When a channel is programmed with a static level of high, the pulse
will be low-going. When a channel is programmed with a static level of low, the pulse will be
high-going. Each pulse generation requires a separate command.
The electrical specifications for the digital I/O port are provided in Table 3-1. Particular note
should be given to the VINPUT specification of -0.5 V to 5.5 V. Exceeding that value with an
external voltage source, even through a resistance, could permanently damage the EX7000.
Characteristic
VINPUT
Value
-0.5 V to 5.5 V
2 V min
VIH
VIL
0.8 V max
2 V min
0.55 V max
VOH (IOH = -32 mA)
VOL (IOL = 64 mA)
TABLE 3-1: DIGITAL I/O PORT ELECTRICAL SPECIFICATIONS
General Purpose I/O
The EX72SF features an additional 32-bit general purpose TTL I/O port. This is in additional to
the internal 72-channel relay drivers and the 8-bit digital I/O described above. The following are
the pin assignments for the rear-mounted 37-pin D-sub connector:
Pin
1
2
3
4
5
6
7
8
Signal
GND
Pin
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
Signal
PIO-PORT0
PIO-PORT2
PIO-PORT4
PIO-PORT6
PIO-PORT8
PIO-PORT10
PIO-PORT12
PIO-PORT14
GND
PIO-PORT1
PIO-PORT3
PIO-PORT5
PIO-PORT7
PIO-PORT9
PIO-PORT11
PIO-PORT13
PIO-PORT15
+5 V
PIO-PORT16
PIO-PORT18
PIO-PORT20
PIO-PORT22
PIO-PORT24
PIO-PORT26
PIO-PORT28
PIO-PORT30
GND
9
10
11
12
13
14
15
16
17
18
19
GND
PIO-PORT17
PIO-PORT19
PIO-PORT21
PIO-PORT23
PIO-PORT25
PIO-PORT27
PIO-PORT29
PIO-PORT31
A current limited supply of +5 V is provided on pin 10. An internal, resettable fuse is provided to
protect 200 mA against excessive current flow and short circuits.
EX7000 Series Basic Operation
21
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
Reset Button
The reset button, accessible through a hole in the rear panel of the EX7000, implemented
according to the LXI LAN Configuration Initialize (LCI) Mechanism specification, can be used to
restore default network settings. This is useful for recovery from an incorrect or unknown network
configuration. To perform a network reset:
1) Press and hold the reset button.
2) Continue to hold the reset until the LAN LED flashes (approximately 5 s).
3) Release the reset button.
The EX7000 will now revert back to the default network configuration (DHCP and AutoIP
enabled) instead of its previous settings. VXI-11 Discovery (supported by the VISA IO-Libraries)
can be used to determine the IP address of the instrument.
FRONT PANEL VIEW
The front panel of each EX7000 model is different. The EX71HD front panel is configured with
twelve identical mounting locations for miniature microwave switch modules. The EX72SF front
panel is configured with twelve locations for latching microwave switches. The twelve locations
are divided into six locations for SPDT switches and six locations for SPnT and/or transfer
switches. The EX7400 will be configured to satisfy its unique customer specified requirements.
Details for each EX7400 are supplied as supplements to this manual and are generally printed on
yellow paper.
EX71HD
The EX71HD enclosure, shown in Figure 1-1, and switch modules are fitted with blind mating
connectors to simplify switch module removal and installation. The mounting plate on the
switches contains two rear facing alignment pins that fit into holes on the front panel. These pins
only allow full insertion of the switch into the EX71HD enclosure opening when properly aligned.
NOTE
Before proceeding with the removal and/or installation of any microwave switch modules in any
of the EX7000 Series assemblies, turn the ac power switch to the OFF position and remove the ac
power cord.
To remove a switch from the enclosure, simply remove the four miniature hex head cap screws
from the four corners of the switch using a 5/64” hex key wrench and pull the switch forward.
There will be some slight resistance until the blind mate connectors disengage.
Installation is in the reverse order. Carefully insert the multi-pin connector end of the switch into
the opening, turning the switch module to arrange the two alignment pins to be on the top side of
the switch. Insert straight back until the blind mating connector alignment pins engage. Once these
alignment pins are engaged, press firmly until the switch slides in flush with the EX71HD front
panel. Insert and tighten the four 2-56 hex head cap screws.
Following the mechanical installation, the EX72HD needs to have its configuration file updated.
This will not be necessary for cases where a switch is simply replaced with another of the same
model. The configuration file tells the internal control and drive circuitry exactly what is
connected to each port of the unit. Updating the Configuration file is accomplished by running the
Configurator software tool and following the intuitive prompts. Consult the Configurator User’s
Manual for details. Alternatively, the new configuration file can be generated by the factory and
downloaded over the Internet. Consult the factory for details.
22
EX7000 Series Basic Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
EX72SF
The EX7SF enclosure , shown in Figure 1-2,can accommodate a large number and various types
of Agilent latching switch modules. The upper six switch mounting locations, designated SW1 to
SW6, are designed for SPDT switches. The lower six switch mounting locations, designated SW7
to SW12, are designed for SP4T, SP6T, and transfer switches.
The following table provides the switch model choices for these sections:
VTI MODEL
SPDT (SW 1 – 6)
7202-20
DESCRIPTION
AGILENT MODEL NUMBER
SPDT, 20 GHz
8765B
7202-26
SPDT, 26 GHz
8765C
7202-20T
7202-26T
87202-20T
87202-26T
SP4T (SW7-12)
7204-20
7204-26
7204-20T
7204-26T
87204-20T
87204-26T
SP6T (SW7-12)
7206-20
7206-26
7206-20T
SPDT, T, 20 GHz
SPDT, T, 26 GHz
SPDT, T, EL, 20 GHz
SPDT, T, EL, 26 GHz
8762B
8762C
N1810TL - 020
N1810TL - 026
SP4T, 20 GHz
SP4T, 26 GHz
SP4T, T, 20 GHz
SP4T, T, 26 GHz
SP4T, T, EL, 20 GHz
SP4T, T, EL, 26 GHz
L7204B
L7204C
L7104B
L7104C
87104B
87104C
SP6T, 20 GHz
SP6T, 26 GHz
SP6T, T, 20 GHz
SP6T, T, 26 GHz
SP6T, T, EL, 20 GHz
SP6T, T, EL, 26 GHz
L7206B
L7206C
L7106B
L7106C
87106B
87106C
7206-26T
87206-20T
87206-26T
Transfer (SW7-12)
7222-26
Transfer, 26 GHz
Transfer, EL, 26 GHz
L7222C
87222C
87222-26
TABLE 3-2: EX72SF SWITCH MODULES
The SPDT switches are mounted on special carriers for installation into the EX72SF and are
delivered this way if ordered separately from the factory. The SP4T and SP6T switches mount
directly in the lower openings and do not require any special carriers. The transfer switches do not
have the same square mounting plate as the multi-throw switches so they require a special carrier
for mounting in the lower round openings.
NOTE
Before proceeding with the removal and/or installation of any microwave switch modules in an
EX7000, turn the ac power switch to the OFF position and remove the ac power cord.
To remove a SPDT switch from the enclosure, simply remove the two pan head Philips screws
from each side of the individual switch faceplate. Remove the faceplate and slide the switch
forward until it is away from the enclosure and far enough out to expose the white plastic 8-pin in-
line connector. Firmly grasp each end of the white plastic body, squeezing the release tab on the
enclosure side and pull until the two parts separate.
NOTE
The new switch modules must have the cable assembly with the white plastic multi-pin connector
installed in order for it to interface with the internal control circuitry. All replacement or add-on
relays supplied by VTI Microwave will have this cable in place. Contact VTI Microwave
immediately if your switch module arrives without this cable assembly as well as the universal
mounting carrier installed.
EX7000 Series Basic Operation
23
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
Installation is in the reverse order. Carefully insert the multi-pin white plastic connector, at the end
of the switch module cable, into the mating cable extending from the EX72SF enclosure opening.
Press the two plastic connectors firmly together until you can feel slight clicking action as the
release tab on the enclosure side connector drops into place, locking the two connectors together.
Next, align the sides of the carrier with the dark plastic card guides on each side of the rectangular
opening. Slide the switch and carrier all the way in until it reaches the rear stop which should
place the front body of the connector approximately flush with the front panel of the enclosure.
Place the faceplate back in position and secure with the two pan head Philips screws.
To remove a SP4T or SP6T switches from the enclosure, simply remove the four flat head Philips
screws from each corner of the switch. Slide the switch forward until it is away from the enclosure
and far enough out to access the 16 pin ribbon cable connector plugged into the rear of the switch.
Pull the release tab on the rear of the switch away from the connector and pull the ribbon cable
connector out of the switch.
Installation is in the reverse order. Carefully insert the ribbon cable connector into the mating
connector on the switch module. Align the ribbon cable connector tab with the release tab on the
switch’s connector. Press the ribbon cable connector firmly in until the release tab on the switch
clicks into place locking the connector in place. Slide the switch all the way in until it the
mounting flange is flush with the front panel of the enclosure. The switch can operate in any
orientation but the standard configuration is for the #1 port to be closest to the right side of the
enclosure which puts port 5 and 6 at the top. Align the four holes and secure with the four flat
head Philips head screws.
Following the mechanical installation, the EX72SF needs to have its Configuration file updated.
This will not be necessary for cases where a switch is simply replaced with another of the same
model. The Configuration file tells the internal control and drive circuitry exactly what is
connected to each port of the unit. Updating the Configuration file is accomplished by running the
Configurator software tool and following the intuitive prompts. Consult the Configurator User’s
manual for details. Alternatively, the new Configuration file can be generated by the factory and
downloaded over the Internet. Consult the factory for details.
EX7400
Generally speaking, most EX7400 models will have their switches mounted internally and are not
intended for easy field upgrades or repairs. Please contact the VTI Microwave in the event of a
failure.
24
EX7000 Series Basic Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4
WEB PAGE OPERATION
INTRODUCTION
The EX7000 offers an embedded web page which provides network configuration control, soft
front panel access, time configuration, and the ability to perform firmware upgrades. To open this
web page, enter the EX7000’s assigned IP address or host name into an Internet browser
application, as shown in Figure 4-1.
FIGURE 4-1: IP ADDRESS ENTERED INTO INTERNET BROWSER
GENERAL WEB PAGE OPERATION
When initial connection is made to the EX7000, the instrument home page, Index, appears (see
Figure 4-2. This page displays instrument-specific information including:
•
•
•
•
•
•
•
•
•
•
•
Model
Manufacturer
Serial Number
Description
LXI Class
LXI Version
Hostname
MAC Address
IP Address
Netmask
Firmware version
This page is accessible from any other instrument page by clicking on the EX7000 web page
header.
The EX7000 command menu is displayed on the left-hand side of every internal web page. The
entries on the command menu represent three types of pages:
Status
Action
Entry
This type of page performs no action and accepts no entries. It provides operational
status and information only. The Index page is an example of a status page.
This type of page initiates a command on the instrument, but does not involve
parameter entry. The Reboot page is an example of an action page.
This type of page displays and accepts changes to the configuration of the instrument.
The Time Configuration page is an example of an entry page.
EX7000 Series Web Page Operation
25
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
Use of the entry-type web pages in the EX7000 are governed by a common set of operational
characteristics:
•
•
Pages initially load with the currently-entered selections displayed.
Each page contains a Submit button to accept newly entered changes. Leaving a page before
submitting any changes has the effect of canceling the changes, leaving the instrument in its
original state.
•
Navigation through a parameter screen is done with the Tab key. The Enter key has the same
function as clicking the Submit button and cannot be used for navigation.
FIGURE 4-2: EX7000 MAIN WEB PAGE
Password Protection
Once the IP address has been entered into the address bar of a web browser, the user should define
a password for the EX7000. No password is defined by default. To create a password, click on the
Change Password link in the command menu, then enter the desired password in both text fields.
From this point forward, pages that modify instrument configuration (e.g., Soft Front Panel)
require this password to initially login. It is only necessary to enter a password once per session.
26
EX7000 Series Web Page Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 4-3: EX7000 PASSWORD PAGE
NOTES
1) The instrument password uses lower-case letters.
2) This password mechanism provides only the most basic security. Applications requiring
additional security should consider using private, dedicated subnets, firewalls, etc. to limit
access to the instrument on the network.
VXI Technology Logo
The VXI Technology logo that appears on the upper left of all EX7000 web pages is a link to the
EX7000 Title Block
The title block (“EX7000” on a black background at the top of the page) of all EX7000 web pages
is a link to the Main Web Page.
EX7000 Series Web Page Operation
27
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
SOFT FRONT PANEL
An example of the EX7000 Soft Front Panel page can be seen in Figure 4-4. By accessing this
page, the various switch modules, attenuators, and other devices connected to the EX7000 can be
viewed, identified, and commanded.
FIGURE 4-4: EX7000 SOFT FRONT PANEL PAGE
28
EX7000 Series Web Page Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
NETWORK CONFIGURATION
The EX7000 Network Configuration page can be seen in Figure 4-5. By default, the EX7000 will
attempt to locate a DHCP server. If one is found, the IP address assigned by the DHCP server will
be assumed, along with subnet masks, gateway, etc. Otherwise, after a timeout of 20 seconds, the
unit will attempt to obtain an IP address by using AutoIP (IPv4 Dynamic Link Local Addressing).
NOTE
The EX7000 can be returned to a known, default network configuration by using the LCI (LAN
Configuration Initialize) Mechanism. See Reset Button for more information.
AutoIP is a mechanism for finding an unused IP address in the IANA assigned range 169.254.X.Y
(169.254/16) where X is in the range 1 - 254 and Y is in the range 0 - 255. The device will first
attempt to obtain the specific address 169.254.X.Y, where X and Y are the second-to-last and last
octets of the device’s MAC address. However, X will be set to 1 if it is 0 in the MAC address, and
to 254 if it is 255 in the MAC address for conformance with the AutoIP specifications. If this
address is already in use, the unit will attempt to obtain other IP addresses in the 169.254/16 range
in a pseudorandom fashion until it finds one that is available.
To illustrate the AutoIP mechanism, Table 4-1 lists the AutoIP default address for some example
MAC addresses.
MAC Address
00:0D:3F:01:00:01
00:0D:3F:01:01:01
00:0D:3F:01:A3:28
00:0D:3F:01:FE:FE
00:0D:3F:01:FF:FE
AutoIP Default Address
169.254.1.1
169.254.1.1
169.254.163.40
169.254.254.254
169.254.254.254
TABLE 4-1: AUTOIP DEFAULT ADDRESS ASSIGNMENT
If a static IP address assignment is preferred, one can be optionally assigned via the embedded
web page interface. This is done by clicking the Network Configuration link, disabling DHCP
and AutoIP, enabling Static, and then assigning a static IP address, subnet mask, and gateway
address, and, optionally, up to three DNS servers (see Figure 4-5).
EX7000 Series Web Page Operation
29
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
FIGURE 4-5: EX7000 NETWORK CONFIGURATION
NOTE
The 169.254/16 subnet is reserved by the IANA for AutoIP usage. It should not be used for either
DHCP or static IP configurations.
However, a much more convenient and recommended way to obtain the benefits of a static IP
address is to employ DHCP, but assign the instrument a reserved IP address in your company’s
DHCP server configuration. This reserved address, linked to the EX7000’s MAC address on the
DHCP server, would be assigned to the EX7000 at power up initialization without having to
manually set it on the EX7000. The DHCP server configuration provides a centralized, controlled
database of assigned IP addresses, preventing accidental assignment of the same IP address to
multiple instruments. Consult your company’s Information Technology department for assistance.
VXI-11 Device Discovery is also supported by the EX7000. This allows all EX7000s on a local
network to be found without knowledge of their MAC address or IP address with the use of a
broadcast message. Additionally, the EX7000 provides MDSN (multicast domain name system)
support and may be discovered by software such as Bonjour®.
30
EX7000 Series Web Page Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
TIME CONFIGURATION
This entry page is used to change the time configuration of the EX7000. By default, the instrument
has no notion of “wall-clock” or calendar time. The instrument has no battery-backed clock or any
other mechanism to retain time between reboots and power-cycles. By default, the instrument’s
time and date at power-up are midnight, January 1, 1970 (the beginning of the “epoch”). The time
and date can be manually specified on the Time Configuration page (Figure 4-6). Manual
configuration will be necessary if the network environment is such that the instrument cannot
reach the Internet. Manual time entry is not affected by the Time Zone control and does not
require an instrument reboot to be activated. However, manually-specified time is volatile, and,
therefore, must be reentered upon an instrument reboot or power cycle. It is not, however, affected
by the Reset page.
FIGURE 4-6: EX7000 TIME CONFIGURATION WEB PAGE – MANUAL
Optionally, the EX7000 supports SNTP (Simple Network Time Protocol), allowing it to receive its
time from an SNTP server. The Time Zone control provides a pull-down selection in which the
user’s specific time zone is selected. SNTP or PTP (Peer-To-Peer Time Synchronization or IEEE
1588) servers are specified in the Server configuration panel, by IP Address or hostname. An
instrument reboot is then required to activate the new selection.
EX7000 Series Web Page Operation
31
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
FIGURE 4-7: TIME CONFIGURATION WEB PAGE – SNTP
FIGURE 4-8: TIME CONFIGURATION WEB PAGE – PTP
32
EX7000 Series Web Page Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
Specifying SNTP or NTP servers by hostname requires that the instrument be configured for DNS,
either by DHCP or Static IP.
DEVICE IDENTIFY
This action page is used to identify the EX7000 that is being commanded in the current session.
When the “Turn on” button is pressed, the LAN LED located on the rear panel of the EX7000 will
blink. When the “Turn off” button is pressed, the LAN LED returns to its normal operation.
FIGURE 4-9: DEVICE IDENTIFY WEB PAGE
UPGRADE
This action page is used to upgrade the embedded firmware of the EX7000. Prior to initiating the
firmware upgrade process, a new, uncompressed firmware image must be obtained from
VXI Technology and be accessible from the computer that is connected to the EX7000. Unless
specifically noted by VXI Technology, firmware upgrades do not alter the non-volatile
configuration settings (network configuration, time configuration) of the EX7000.
NOTE
Do not power cycle the EX7000 during the firmware upgrade process. If power is lost during the
upgrade, the instrument may be put into an inoperable state, requiring return to the factory. An
uninterruptible power supply may be used to avoid this risk.
EX7000 Series Web Page Operation
33
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
FIGURE 4-10: UPGRADE WEB PAGE
Perform the following steps to conduct a firmware upgrade:
1) Perform a Reboot or a power cycle.
2) Connect to the EX7000 via the embedded web page.
3) Click on the Upgrade link.
4) Click on the Browse button and select the firmware image file to be uploaded to the
instrument.
5) Click the Submit button to initiate the upgrade process.
The upgrade process takes approximately 5 minutes to complete and will be followed by a prompt
to reboot the instrument. Once the reboot is complete, reconnect and confirm on the Index page
that the firmware revision level has been properly updated.
RESET
This action page is used to return the EX7000 to a known communication state. Pressing the Reset
button will cause the EX7000 to terminate all active sessions, leaving only the current session
viable.
REBOOT
This action page is used to perform a complete instrument reboot, equivalent to that which occurs
when the instrument is power cycled. It is most commonly used to accept changes that are made to
the network configuration or time configuration settings. In addition, it is suggested that a reboot
be performed before conducting a firmware upgrade.
34
EX7000 Series Web Page Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5
THEORY OF OPERATION
INTRODUCTION
This section expands on the description of the internal operation of the EX7000 and explains how
to best use them. A full understanding of this operation is not required to operate and use the
EX7000. A functional block diagram is provided below.
FIGURE 5-1: FUNCTIONAL BLOCK DIAGRAM
SYSTEM OVERVIEW
Using the drivers provided with the EX7000, commands are issued from the host PC to the Digital
Controller Board (DCB). The DCB, in turn, controls the operation of the RDBs. Up to eight RDBs
can be controlled by one DCB, making the EX7000 capable of providing up to 576 high-current
relay control drivers, 96 very high-current drivers, and 256 parallel I/O ports. This is illustrated in
Figure 5-1.When multiple RDBs exist in an EX7000 system, a rotary switch on the RDB is used to
set a unique address for each RDB.
EX7000 Series Web Page Operation
35
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
RDBs can either be commanded one board at a time or several RDBs may be commanded
simultaneously. The RDB has 72 relay control drive lines capable of sinking 200 mA and twelve
very high-current reset lines capable of sinking 800 mA. They are divided into three banks, each
can be powered separately. Each bank consists of four 20-pin connectors. Each connectors
consists of:
•
•
•
•
•
•
•
six high-current drive lines
six indicator/status bits
one very high-current reset line
four relay ID bits
one relay power input
one 5 V input
one ground
NOTE
All devices connected to a particular bank (i.e. group of four connectors) must be of the same
type: continuous or latching. Mixing of different type may result in erratic behavior and damage to
overall system.
OPEN-COLLECTOR VS. TTL DRIVE LINES
The EX7300 and EX7400 relay drive connectors reside on a (RDBs) that are partitioned into three
banks: J2 through J5 constitute bank 0, J6 through J10 bank 1, and J11 through J14 bank 2.
Although a single RDB may contain both latching and non-latching devices, the banks may only
contain one type of device. For example, if J2, J3, and J4 are connected to non-latching devices, J5
may only contain a non-latching relay. A latching relay could, however, be installed in J6.
J13
J12
J11
J10
J9
J8
J7
J6
J5
J4
J3
J2
Relay Driver Board (RDB)
Some connectors have been removed for clarity.
Bank 2
Bank 1
Bank 0
FIGURE 5-2: RELAY DRIVE CONNECTOR BANKS
Additionally, the RDB of the EX7300 and EX7400 may have varying quantities of open-collector
and TTL drive lines, depending on the model ordered. This property is linked to the relay drive
connector banks, as illustrated in Figure 5-2. The following table indicates how banks are used
according the part number assigned.
36
EX7000 Series Web Page Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Number
-000
Bank 0
Open-collector
TTL
Bank 1
Open-collector
Open-collector
TTL
Bank 2
Open-collector
Open-collector
Open-collector
TTL
-001
-002
-003
TTL
TTL
TTL
CAUTION
It is imperative that TTL banks only have TTL devices connected to them. Connecting an
open-collector device to a TTL port will result in damage to the RDB and, potentially, to
other equipment in the test system. Failure to comply with this warning will result in voiding
the manufacturer’s warranty.
RELAY ACCESS & CONTROL
FIGURE 5-3: RELAY DRIVER BLOCK DIAGRAM
When asserted, the relay drive lines will sink the necessary current through the coils, effectively
switching the relay. The user can program the relay settling time for each RDB.
The relay control can be operated in two modes: Pulse and Continuous
Continuous Mode
Connecting non-latching devices to any bank of the RDB will dictate that bank must be operating
in continuous mode. Commanded by software, the latch signal driving the FET will change state
to activate/deactivate FETs and continuously stay in that state until the next command. All Relay
Control Drive bits within a bank will change state at the same time. Continuous mode requires a
power supply capable of sustaining the high-current requirement. The user must allow an
appropriate amount of time after the Relay Control Drive bit changes state for the relay to settle.
This is typically between 10 ms to 30 ms.
EX7000 Series Web Page Operation
37
Download from Www.Somanuals.com. All Manuals Search And Download.
VXI Technology, Inc.
FIGURE 5-4: CONTINUOUS OPERATION MODE
Pulse Mode
Connecting latching devices to any bank of the RDB will dictate that bank must be operating in
pulse mode. Commanded by software, the latch signal driving the FET will change state to
activate FETs and then change state back when the settling time is reached. All Relay Control
Drive bits within a bank will change state at the same time. Certain latching devices will require a
reset signal to move all latches to a known state prior to a new state is applied. The Reset signal
will be a pulse with the same duration as the Relay Control Drive. The pulse width should exceed
the settling time specification for the relays being used. This value will be used as both pulse
width and settling time.
FIGURE 5-5: PULSE OPERATION MODE
NOTE
There is no current monitoring capability on the EX7000. It is the user’s responsibility to estimate
the total current requirement and provide sufficient power supply current.
The user can mix and match non-latching and latching devices among the banks. For instance,
bank 1 and 3 can be all latching, bank 2 can be non-latching. The RDB, if set up properly, will be
able to control all of the devices.
In case of multiple RDBs, all devices in different boards can be controlled in parallel as long as
the current requirement is met. The user does not have to wait for one RDB to finish its operation
before moving to the next. On the contrary, the user can also control one RDB at time. The settling
time in case of multiple RDB will be the longest between the boards, multiply with the aggregate
number of banks connecting to latching devices.
38
EX7000 Series Web Page Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
A
O
AutoIP.......................................................................................16, 29
open-collector device warning.......................................................37
C
P
configuration table..........................................................................13
connectors.......................................................................................14
continuous mode.............................................................................37
password.........................................................................................26
power specifications.......................................................................14
processor.........................................................................................14
programmable MBB and BBM......................................................13
PTP .................................................................................................31
pulse mode......................................................................................38
D
declaration of conformity.................................................................6
device idnetify web page................................................................33
DHCP........................................................................................16, 29
digital I/O........................................................................................21
digital I/O connector.......................................................................20
driver.........................................................................................15, 16
driver installation............................................................................16
R
RDB................................................................ See relay driver board
rear panel view ...............................................................................19
reboot web page .............................................................................34
relay drive control ..........................................................................12
relay driver board ...................................................12, 35, 36, 37, 38
relay odometer................................................................................13
reset
network configuration..............................................................22
reset button .....................................................................................22
reset web page ................................................................................34
E
EX71HD .....................................................................................9, 22
EX72SF ..............................................................................10, 23, 24
EX72SF switch modules ................................................................23
EX7400...........................................................................................24
exclude lists ....................................................................................13
S
F
scan lists .........................................................................................13
SNTP ..............................................................................................31
soft front panel web page...............................................................28
specifications..................................................................................14
firmware upgrade web page ...........................................................33
front panel.......................................................................................22
G
T
general purpose I/O ........................................................................21
TCP.......................................................... See network configuration
theory of operation .........................................................................35
time configuration web page..........................................................31
H
hardware setup................................................................................16
V
I
VXI-11 device discovery ...............................................................30
index web page...............................................................................25
installation location ........................................................................15
IP address.................................................See network configuration
W
Web Page Operation ......................................................................25
WEEE...............................................................................................7
L
LAN Configuration Initialize.............................................16, 22, 29
LCI................................................See LAN Configuration Initialize
LXI Trigger Bus .............................................................................20
M
MAC address............................................................................16, 29
MDSN........................................ See multicast domain name system
multicast domain name system ......................................................30
N
network configuration
resetting ...................................See LAN configuration initialize
network configuration web page....................................................29
EX7000 Series Index
39
Download from Www.Somanuals.com. All Manuals Search And Download.
|