Operation Instructions
Verona CR 43
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel Description
1 ON/OFF
5 Cassette compartment
; Preset buttons 1, 2, 3, 4, 5, 6
Store station - Keep button depressed
during radio operation until the station
becomes audible again.
Switch the set on/off by turning the
knob.
If “Cod” appears on the display, read
the chapter “Anit-Theft Coding” first.
Volume control:
6 Track indication
- side A or 1 is played
- side B or 2 is played (reverse ope-
ration)
Recall station - Briefly press the re-
spective button.
By turning the knob
Coding - Read the “Anti-Theft Coding”
chapter first.
Buttons 1 - 4: Use to enter a four-digit
code number.
Press each of the buttons until the four-
digit code to be found in the car radio
passport is represented on the display.
SCAN (search operation):
During radio reception, the stations are
briefly sampled by pressing the knob for
approx. one second.
7 FR button (Fast Rewind)
Fast rewind of the tape.
Deactivate: press button FF.
Balance:
8 PROG (Autoreverse)
Pull knob and adjust left/right volume by
turning the knob.
For shifting to the other side of the tape
- press both buttons.
< lo rocker switch
Use this button to alter the sensitivity of
the automatic station seek operation.
lo lights up on the display - normal sen-
sitivity
2
/
rocker switch
9 FF button (Fast Forward)
Radio: Automatical station tuning
Coding: Read first the “Anti-Theft
Coding” chapter.
Fast forward of the tape
Deactivate: press button FR.
lo does not light up - high sensitivity
: Press rocker switch
to confirm your code
entry.
: Display for
Additional function of the lo rocker
switch:
Switching from stereo to mono:
Press longer than 2 seconds.
3 << / >> rocker switch
frequency
waveband
For fine tuning of the stations
4
Ejection of the tape
Press button firmly.
preset button
storage level
stereo
seek tuning
(sensitivity)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
= M•L rocker switch (Medium wave -
Long wave)
@ TREB (Treble)
to adjust trebles.
Use this rocker switch to select either
medium wave (MW) or long wave (LW)
frequencies. To switch between these
wavebands simply press the rocker
switch again.
A BASS
to adjust basses.
B FAD (Fader)
(front/rear volume):
adjust using the lever.
> FM•T button (Frequency Modulation)
This button is used for shifting between
the different FM storage levels I, II, III
and T (Travelstore - i.e. storing and
calling the six strongest stations of an
area).
Storing “T” - Press the FM •T button
until the seek tuning indication starts to
be displayed.
Recalling “T” - Press the FM•T button
? until T is indicated on the display.
Then briefly press the respective preset
button.“Balance” knob
To adjust the volume of the left and
right channel
? PS rocker switch (Preset Station Scan)
Pressing this button briefly samples all
memorized stations of the selected
waveband (FM, MW, LW or TS).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Important Notes............................ 16
Radio Section ............................... 18
What You Should Read By All Means! . 16
Safety Notes ......................................... 16
Road Safety ....................................... 16
Selection of the Desired Waveband...... 18
Automatic Station Tuning ...................... 18
Manual Tuning ...................................... 18
Adjusting the Station Seek Sensitivity... 18
Adjusting the local mode sensitivity ...... 18
Switching between Stereo and Mono ... 18
Storing a Station ................................... 19
Automatically Storing the Strongest
Anti-Theft Coding ......................... 16
Wrong Code Number Entered ........... 16
First-time Operation and Restart
Following Interruption of Power
Supply................................................ 16
Switching Code System Off ............... 17
Switching the Code System Back On If
you wish to re-activate the anti-theft
code system: ..................................... 17
Optical indication of theft protection .. 17
Stations ................................................. 19
Activating a Stored Station.................... 19
Briefly Sampling a Station ..................... 19
Sampling Memorized Stations .............. 19
Tape Section ................................. 20
Inserting the Tape ................................. 20
Removing the Tape............................... 20
Fast Forwarding/Rewinding of the Tape 20
Autoreverse........................................... 20
Care Notes ............................................ 21
Amplifier Section.......................... 17
ON/OFF ................................................ 17
Balance Control .................................... 17
Fader control ......................................... 17
Appendix ....................................... 21
Technical Data ...................................... 21
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Notes
Anti-Theft Coding
our central customer service workshop or to
one of our dealers in your vicinity.
What You Should Read By All
Means!
Your radio is protected against theft by an
anti-theft coding system. If, once the unit has
been encoded, the power is disconnected
from the set (e.g. theft, disconnection of the
car battery or prior to installation), the set is
Beforestartingtouseyournewcarradio, you
should carefully read through the safety no-
tes and the information about “Anti-Theft
Coding”.
First-time Operation and Restart Follo-
wing Interruption of Power Supply
electronically blocked. It may only be used ● Switch on set.
again after the appropriate code number has
been entered (see car radio pass). Hence, a
coded set is of no use to a potential thief.
“Cod” will appear in the display :.
● Briefly press preset button 1 ;, “000”
Safety Notes
will appear in the display :.
Road Safety
● Enter the code number from the Blau-
Beingthedriverofamotorvehicleyoushould Wrong Code Number Entered
punkt car radio pass:
dedicateyourfullattentiontothetrafficaround
you. Therefore always use your car stereo
such that you are able to cope with the
present traffic situation in any moment.
In difficult driving situations you should turn
your set off. Please take into account that at
a speed of 50 km/h you are almost covering
a distance of 14 m per second!
When adjusting the volume, always make
sure that acoustic signals from the outside
can still be heard in order to be able to react
to alert signals just as it is required by the
present situation.
It should not be possible for thieves to ascer-
tain the code number by trial-and-error. This
is why the set is blocked for a certain period
of time if an incorrect code number is ente-
red. “---” would then appear in the display:.
This time period is 10 seconds following the
first three attempts, and is increased to 1
hour following subsequent attempts.
Example: Code number is 1521
● - press preset button 1 ; once,
“1000” appears in the display :,
- press preset button 2 ; 5 times,
“1500” appears in the display :,
- press preset button 3 ; 2 times,
“1520” appears in the display :,
- press preset button 4 ; once,
“1521” appears in the display :.
After 19 unsuccessful attempts “OFF” will
appear in the display : and the set can no
longer be started.
● Confirm code number:
Press upper part of rocker switch
/
Note:
2.
Keep your car radio pass, which contains the
codenumber, inasafeplaceinordertoavoid
“unauthorized access” to your car radio. If
you lose your radio pass and have forgotten
your code number you will not be able to
restart the set after the power supply has
been interrupted. The only way to make the
set operable again is by sending the radio to
Note:
Using preset button 1 the set can only be
adjustedto“1”or“0”.“0”isnotindicatedinthe
display.
If you have entered and confirmed an incor-
rect code number, “---” will initially appear in
the display : and then, after a certain time
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Amplifier Section
period, “000”. Following this, it is essential
that you enter the correct code number.
ON/OFF
The anti-theft code system is now activated.
Now whenever the set is turned on, “CODE”
will appear briefly in the display :.
For switching the set on,
● turn button 1
.
Switching Code System Off
If you wish to switch the anti-theft code sy-
stem off:
Your stereo is now ready for operation.
Optical indication of theft protection
As optical warning of the encoded car radio,
For switching the set off,
● turn off the radio,
the LED
6 flashes when the ignition is
● turn button 1
.
switched off, provided the car radio has been
connected correspondingly.
Forthis, pleaseseethecorrespondinginstal-
lation instructions.
● simultaneously press, and hold, preset
buttons 1 and 4 ;
Volume control
● turn the set back on. “Cod” will then
● turn button 1.
appear in the display :.
● release the preset buttons 1 and 4 ;.
Balance Control
“000” then appears in the display :.
Use button 1 to balance the sound impres-
sion of the right and left channel speaker.
● Enter the code number that is in the
Blaupunkt car radio pass and confirm:
See example “First-time operation ...”.
● Pull (lock in) button and turn.
The anti-theft coding system has now been
deactivated.
After the adjustment
● slightly press button.
Switching the Code System Back On If
you wish to re-activate the anti-theft
code system:
Fader control
If four loudspeaker are connected, the front/
rear sound impression of the loudspeakers
(fader) can also be modified using lever B.
● turn the radio off,
● simultaneously press, and keep de-
pressed, preset buttons 1 and 4 ;,
● turn the set back on. “Cod” briefly ap-
pears in the display : and then the set
is switched on.
Adjusting trebles
● turn button @.
Adjusting basses
● turn button A.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio Section
Tuning of Previous Station
● Press rocker switch
Selection of the Desired Wave-
band
Adjusting the local mode sensiti-
/
2 down. The vity
radio will automatically seek the previ-
ous station.
This radio allows you to choose between the
FM, MW and LW wavebands.
In regions with extremely high station densi-
ty, e.g. in Italy, the set allows you to switch
over the station seek sensitivity for the ocal
mode from “High” (adjusted ex works) to
“Low”. “Low” means that station seek tuning
only captures the most powerful stations.
For modifying the local mode:
If the rocker switch
/
2 is held
down/up, the seek operation continues
to be carried out quickly in the corre-
sponding direction.
FM Selection
● Briefly press the FM•T rocker switch
>. “FM” is displayed in the display (for
Frequency Modulation).
Manual Tuning
● press button lo < longer than 8 secs.
Itisalsopossibletotuneinstations“byhand”
with this radio:
The display : shows “L” for “Low”.
By pressing button lo < again longer than
MW or LW Selection
● Briefly press the M•L rocker switch =.
An “M” (for MW), or an “L” (for LW) will
then appear in the display.
● Press rocker switch <</>> 3 to the left 8 secs., the set switches back to “High” (dis-
or to the right. The frequency band is
scanned in small steps.
play : “H”).
Whenswitchingofftheunitorwhenremoving
the set with the QuickOut handle the set
remains in the last activated mode.
If you wish to switch between MW and LW:
● press the M•L rocker switch = again.
The following instructions apply for all wave-
bands, as long as not otherwise indicated.
Adjusting the Station Seek
Sensitivity
Switching between Stereo and
Mono
You may also modify the sensitivity of the
automatic station seek operation.
For this:
Automatic Station Tuning
If you wish to switch between stereo and
mono:
Tuning of Subsequent Station
● press lo rocker switch <.
If “lo” is indicated, only stations with
good reception conditions are captured
(lower sensitivity).
● Press rocker switch
/
2 up. The
● keep the lo button < pressed for long-
er than 2 seconds. The stereo symbol
will appear in the display : if the
stereo mode is activated.
radio will automatically seek the next
station.
If “lo” is not indicated, stations with a
weaker reception are also captured
(higher sensitivity).
The stereo function is activated auto-
matically when you turn your set on.
The set will automatically switch to
mono if reception is poor.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing a Station
Automatically Storing the Stron- Briefly Sampling a Station
gest Stations
You can store one MW and LW station and 4
(Radio Scan)
FMstationsoneachofthepresetbuttons;. (Travelstore)
Starting with the currently tuned in station,
The display will show you the selected wa- WithTravelstore, youhavetheopportunityto you can have the following ones briefly sam-
veband (FM, MW or LW) and preset button. automatically store the six most powerful FM pled for approx. eight seconds each.
On FM, the display will also give you the stationsofyourlocalreceptionareaandhave
chosen storage level (I, II, III or T). them sorted according to their frequencies.
If you wish to change from one storage level This feature is of special use while travelling.
● Press the knob 1 for approx. 1 sec.
If the following station is found, it is
reproduced for approximately eight
seconds.The station’s frequency starts
blinking on display :; if it has already
been memorized, the corresponding
preset button and the storage level indi-
cator starts blinking on display :. Sub-
sequently, the set starts searching for
the next station.
to another:
● Press the FM•T rocker switch > for at
least two seconds.
● press the FM•T button >.
If you wish to store a station:
The set searches for the next FM stati-
ons and sorts them on the “T” (Travel-
store) storage level. Once the process
is finished, the car radio tunes in to the
first station.
● (for FM only) select the storage level.
To achieve this, press the FM•T button
> until I,II,III or T appears in the dis-
play :.
If required, it is also possible to manually For selecting a sampled station:
● tune in the station (see chapter Station
storeastationontheTravelstorelevel. Ifless
than five stations can be received, the free
buttons are represented by dashes for a
short period of time.
● Press the knob 1 once again. The
Tuning).
Scan function is off.
● press the desired preset button ; until
the radio resumes play (approx. 2 se-
conds).
After the search operation has been conclu-
ded, and no station has been chosen, the
radio starts playing the station from which
Station Scan was started before.
The display : indicates which preset
button has been pressed.
The station has now been stored.
Activating a Stored Station
If required, the memorized stations can be
activated at a keystroke.
Sampling Memorized Stations
● Choose the storage level.
For this, press FM•T > until the dis-
play : shows I, II or III, or T.
Note:
Allmemorizedstationsofawavebandcanbe
briefly sampled.
When tuning in an already stored station, the
display : will show the corresponding pre-
set button for approx. five seconds and the
respective storage level.
● Press the PS rocker switch ?.
● Briefly press the required preset button
One after another, the car radio will
then start introducing all memorized
stations of the selected waveband.
;.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Tape Section
The set either samples the stations of
storage levels I-III or of the Travelstore
level “T”. This depends on the current
switching status.
Fast Rewind
Inserting the Tape
● Press the FR (Fast Rewind) button 7.
Once the tape has been completely
rewound, the set begins playing the
tape.
If you wish to play a cassette tape:
● switch the set on
● gently insert the cassette with side 1
If a preset button has no station alloca-
ted, this button is skipped.
upwards.
The tape will then be played in the direction
it was last played.
Track indication 6 indicates which side is
played.
- side A or 1 is played.
- side B or 2 is played (reverse operation).
Stopping the Fast Rewind Operation
To terminate this function:
● Press the PS rocker switch ? once
again.
● Press the FF button 9.
Autoreverse
The station currently sampled is
maintained.
If, while a tape is playing, you wish to switch
to the other side of that tape:
Removing the Tape
● press the FF and FR buttons simulta-
neously.
If you wish to remove the tape:
Attheendofthetapethesetwillautomatical-
ly switch to the other side of the tape.
● press the
then ejected.
button 4. The tape is
Note:
Fast Forwarding/Rewinding of
the Tape
When playing stiff tapes it is also possible to
manually switch to the other side of the tape.
If this is the case, check the tape wound up to
that point; fast forwarding or rewinding often
helps in such cases.
Fast Forward
● Press the FF (Fast Forward) button 9.
At the end of the tape the set will switch to
the other side and resume playing the
tape.
Stopping the Fast Forward Operation
● Press the FR button 7.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Care Notes
Technical Data
We recommend C-60 and C-90 type tapes
for use in any automobile tape player; to
protectyourtapes,storetheminacoolplace
away from dirt, dust, or excessive tempera-
tures above 50° Celsius. In order to ensure
smoothtapeoperation,coldtapesshouldbe
allowed to heat up a bit before they are
played. If dust collects on the audio head or
the rubber roller, problems related to rough
tape operation or poor sound quality may
occur after approx. 100 hours of operation.
For normal contamination, use a head-
cleaning cassette to remove the dust; for
more intensive contamination, use a cotton-
wooltipsoakedwithalcohol.Neverusehard
tools!
Amplifier
Output power:
4 x 4.5 W watts RMS
acc. to DIN 45324/3.1
4 Ω
FM:
Sensitivity:
0.9 µV at 26 dB
signal-to-noise ratio
Frequency
response:
35 - 15 000 Hz (-3 dB)
31.5 - 16 000 Hz (-3 dB)
Tape Section:
Frequency
response:
Modifications reserved!
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Blaupunkt-Werke GmbH
Bosch Telecom
1/93
MC/VKD-Hi 3 D92 147 061
PM
Download from Www.Somanuals.com. All Manuals Search And Download.
|