Table of Contents
Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Included with the
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Important Electrical Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Telephone Line Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Radio Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
More Than One Cordless Telephone . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Selecting a Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Telephone Line Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting the Telephone Cords. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Applying Power to the Base Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Adapter Safety Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Desk or Tabletop Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Wall Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Direct Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Setting up your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Extending the Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Installing the Handset Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . 21
Cleaning the Battery Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Charging the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Low Battery Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Setting the Tone/Pulse Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Adjusting Ringer/Volume Controls . . . . . . . . . . . . . . . . . . . . . . . . . 27
Automatic Digital Code Security. . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using your
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Making and Receiving Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Changing Channels, Hold, Mute, and Flash. . . . . . . . . . . . . . . . . . 33
Using Page/Intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2-Way Paging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Transferring a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Room Monitor Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Programming your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Storing a Number in Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Storing a Tone/Pulse Number With a Pulse Dial System. . . . . . . . 43
Storing One-Touch Dialing Numbers . . . . . . . . . . . . . . . . . . . . . . . 47
Dialing a Stored Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Chain Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Erasing a Stored Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
1
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
A. When the power supply cord is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when following the
operating instructions. (Adjust only those controls that are covered
by the operating instructions. Improper adjustment of other controls
may result in damage and will often require extensive repair work
by a qualified technician.)
E. If the product has been dropped, or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance.
13. Do not use the telephone to report a gas leak in the vicinity of the leak.
Caution: To reduce the risk of fire or injury to persons by the battery, read
and follow these instructions:
1. Use only the appropriate type and size Battery Pack specified in this
Operating Guide.
2. Do not dispose of the Battery Pack in a fire. The cell may explode.
Check the Nickel-Cadmium Battery Disposal package insert for
disposal instructions.
3. Do not open or mutilate the Battery Pack. Released electrolyte is
corrosive and may cause damage to the eyes or skin. It may be toxic if
swallowed.
4. Exercise care in handling the battery in order not to short the battery
with conducting materials such as rings, bracelets, and keys. The
battery or conductor may overheat and cause burns.
5. Charge the Battery Pack provided with or identified for use with this
product only in accordance with the instructions and limitations
specified in the instruction manual provided for this product.
6. Observe proper polarity orientation between the Battery Pack and
battery charger.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Congratulations on your purchase of a Uniden Cordless Telephone. The
is designed with exacting standards to provide reliability, long life,
and outstanding performance.
Features
•
•
•
•
•
•
•
•
25 46/49 MHz Channels
Dual Keypads for added flexibility
UltraClear Plus
AutoTalk
AutoStandby
6 One-Touch Memory Buttons
20 Number Memory
Battery Saving Feature
•
•
•
•
•
•
•
•
Random Code Digital Security
AutoSecure
Tone/Pulse Dialing
2-Way Paging/Intercom
3-Way Communication
Call Transfer
Redial/Pause and Flash
Base/Handset Volume Controls
The
features include AutoTalk and AutoStandby . AutoTalk
allows you to answer a call by just removing the Handset from the Base so
you don’t have to waste time pushing buttons or flipping switches.
AutoStandby allows you hang up by simply returning the Handset to the
Base.
The UltraClear Plus true compander circuitry virtually eliminates background
noise. This innovative technology together with 25 different channels
provides you with the best possible reception during all of your conversations.
To protect you against misbilled calls which might result from your phone
being activated by other equipment, the
has Random Code
digital security which automatically selects one of over 65 thousand digital
security codes for the Handset and Base Units. Also the AutoSecure
feature electronically locks your phone when the Handset is in the Base.
To get the most from your phone, please read this Operating guide
thoroughly. Also be sure to complete the Product Registration form and mail
it in.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Included with the XC3545
If any are missing or damaged, do not contact the place of purchase. Instead
contact Uniden Customer Service at: (800) 297-1023, 8:00 am to 5:00 pm,
Eastern Standard Time, Monday through Friday.
,
Handset
Part No.________
Base Unit
Part No.________
AC Adapter
Part No.________
Long Telephone
Cord
Part No.________
Rechargable Battery
Part No.________
Short Telephone
Cord
Part No.________
®
Operating Guide
OMDX3545
Other Printed
Material
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Electrical Considerations
Unplug all electrical appliances when you know an electrical storm is
approaching. Lightning can pass through your household wiring and damage
any device connected to it. These phones are no exception.
Warning: Please do not attempt to unplug any appliance during an electrical
storm.
Caution: Changes or modifications to this product not expressly approved
by Uniden, or operation of the product in any way other than as
detailed by this Operating Guide, could void your authority to
operate this product.
Range
The
is designed to achieve the maximum possible range by
transmitting and receiving according to the highest specifications set forth by
the FCC. We have rated this phone to operate at a maximum distance with
the qualification that the range depends upon the environment in which the
telephone is used. Many factors limit range, and it would be impossible to
include all the variables in our rating. The Maximum Range rating of your
phone is meant to be used as a means of comparison against other range
claims.
Telephone Line Problems
The FCC has granted the telephone company the right to disconnect service
in the event that your phone causes problems on the telephone line. Also,
the telephone company may make changes in facilities and services which
may effect the operation of your unit. However, your telephone company
must give adequate notice in writing prior to such actions to allow you time
for making necessary arrangements to continue uninterrupted service.
If you are having trouble with your telephone service, you must first
disconnect your phone to determine if it is the cause of your problem. If you
determine that it is the cause, you must leave it disconnected until the
trouble has been corrected.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio Interference
Radio interference may occasionally cause buzzing and humming in your
cordless Handset, or clicking noises in the Base Unit. This interference is
caused by external sources such as TV, refrigerator, vacuum cleaner,
fluorescent lighting, or electrical storm. Your unit is NOT DEFECTIVE. If
these noises continue and are too distracting, please check around your
home to see what appliances may be causing the problem. In addition, we
recommend that the Base not be plugged into a circuit that also powers a
major appliance because of the potential for interference. Be certain that the
antenna on the unit is fully extended when needed.
In the unlikely event that you consistently hear other voices or distracting
transmissions on your phone, you may be receiving radio signals from
another cordless telephone or other source of interference. If you cannot
eliminate this type of interference, you need to change to a different channel.
Finally, it should be noted that some cordless telephones operate at
frequencies that may cause interference to nearby TVs and VCRs; to
minimize or prevent such interference, the base of the cordless telephone
should not be placed near or on top of a TV or VCR; and, if interference is
experienced, moving the cordless telephone farther away from the TV or
VCR will often reduce or eliminate the interference.
More Than One Cordless Telephone
If you want to use more than one cordless telephone in your home, they
must operate on different channels. Press the channel key to select a
channel that provides the clearest communication.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Selecting a Location
Before choosing a location for your new phone, there are some important
guidelines you should consider:
•
The location should be close to both a phone jack and continuous
power outlet. (A continuous power outlet is an AC outlet which does
not have a switch to interrupt its power.)
•
•
•
•
Keep the Base Unit and Handset away from sources of electrical
noise such as motors or fluorescent lighting.
Be sure there is sufficient space to fully extend the Base Unit
antenna.
The Base Unit can be placed on a desk or tabletop or mounted on a
standard AT&T or GTE wall plate.
If you decide to mount your phone on the wall, make sure to change
the handset retainer so that the tab which holds the Handset faces
up. (See page 19 for more information.)
•
You should charge your new phone for 15-20 hours before
completing the installation or using the Handset.
Telephone Line Outlets
There are two types of phone outlets:
Modular Jack
Most phone equipment available now uses modular jacks. Phone
cords are fitted with a molded plastic connector which plugs into
this type of jack. If you do not have modular phone jacks, contact
your local telephone company for information about their
installation.
Hard-wired Jack
Some equipment is wired directly to a phone jack, and these types
of installations require a modular jack converter. This type of
installation is not difficult; however, you should contact your Uniden
telephone dealer or a telephone supply store for advise about the
proper adapter or converter for your particular situation.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Telephone Cords
Consider these safety guidelines before connecting the telephone cords:
CAUTION:
•
•
Never install telephone wiring during a lightning storm.
Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected.
•
Use caution when installing or modifying telephone lines.
Applying Power to the Base Unit
The
requires a standard electrical outlet (120 volts AC without a
switch to interrupt power), and the included AC adapter. Connect the adapter
as shown below.
Wrap the power cord around the
convenient notch on the bottom.
Important: Place the power cord so that it does not create a trip hazard, or
where it could become chafed and create a fire or other
electrical hazards.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Adapter Safety Feature
The AC adapter furnished with this phone may be equipped with a polarized
line plug (a plug having one blade wider than the other). This plug will fit into
the power outlet only one way. If you are unable to insert the plug fully into
the outlet, try reversing the plug.
Do not alter the shape of the
blades of the polarized plug.
Note: If you cannot plug the AC adapter into the outlet, contact someone
about replacing the outlet.
Desk or Tabletop Installation
1. Place the Base on a desk or
tabletop.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Plug the AC Adapter cord
into the 9V DC input jack on
the Base Unit.
3. Place the AC Adapter cord
inside the molded channel.
4. Plug one end of the long
telephone cord into the
TEL LINE jack on the Base
Unit.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Plug the other end of the
cord into the telephone jack
on the wall.
6. Plug the AC Adapter into a
standard 120V AC wall outlet.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Placement of the Handset
The unique design of your phone allows you to place the Handset on the
Base Unit either facedown or in an upright position. The battery is charged in
either position.
Upright Position for
Handset
Facedown Position for
Handset
Wall Installation
Standard Wall Plate Mounting
These phones are designed to be mounted on a standard AT&T or GTE wall
plate.
1. Plug the AC Adapter into the
Base Unit.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Place the AC Adapter cord
inside the molded channel.
3. Plug one end of the short
telephone cord into the
TEL LINE jack on the Base
Unit.
4. Place the telephone cord
inside the molded channel on
the bottom of the Base Unit.
Then plug the other end of
the telephone cord into the
modular jack on the wall.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Place the Base Unit on the
posts of the wall plate and
push down until it’s firmly
seated.
6. Plug the AC Adapter into a
standard 120V AC wall outlet.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Wall Mounting
If you do not have a standard wall plate, you can mount the phone directly
on a wall. Before mounting your phone consider the following:
•
Select a location away from electrical cables, pipes, or other items
behind the mounting location that could cause a hazard when
inserting screws into the wall.
•
•
Make sure the screws are securely fastened.
Make sure the wall material is capable of supporting the weight of
the Base Unit.
1/5 IN.
1. Insert two mounting screws
15
3
⁄ inches apart. Allow
16
about 1⁄5 of an inch between
the wall and screw heads for
mounting the phone.
3 15/16 IN.
2. Plug the AC Adapter into the
Base Unit.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Place the AC Adapter cord
inside the molded channel.
4. Plug one end of the long
telephone cord into the
TEL LINE jack on the Base
Unit.
5. Place the cord inside the
molded channel on the
bottom of the Base Unit.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Place the Base Unit on the
screws and push down until
it’s firmly seated.
7. Plug the other end of the
telephone line cord into the
wall jack.
8. Plug the AC Adapter into a
standard 120V AC wall outlet.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Handset Retainer
The handset retainer holds the Handset in place if your
phone is
mounted on a wall. The steps below describe how to remove and replace the
retainer so that the tab faces up.
1. Push up on the Handset
retainer on the Base Unit,
25 CHANNEL ULTRACLEAR PLUS
and slide the tab out.
2
5
8
2. Flip the retainer over so the
tab faces up.
25 CHANNEL
25 CHANNEL
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Put the retainer back into its
slot on the Base Unit.
CHANNEL
4. Push down on the Handset
retainer until it snaps into
place.
25 CHANNEL
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your Phone
Extending the Antenna
Before using your phone, be
sure to raise its antenna to
the vertical position, and then
extend the antenna.
Installing the Handset Battery Pack
1. Press in on the Battery
Cover Release.
NOTE
R
D
B
21
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Slide the battery
compartment cover down.
3. Align the plastic connector of
the Nickel-Cadmium battery
pack with its socket and plug
it in.
WARNING !
Always Install Battery Cable
with Black Wire closest to
the left
4. Place the battery pack inside
the battery compartment,
and slide the battery cover
back on.
Note: The built-in Memory Backup feature allows up to 3 minutes to
disconnect the old battery pack and install a new one without
losing any phone numbers that may be stored in the telephone’s
memory.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the Battery Contacts
To maintain a good charge, it is important to clean all charging contacts on
the Handset and Base Unit about once a month. Use a pencil eraser or other
contact cleaner. Do not use any liquids or solvents.
Contacts
25 CHANNEL ULTRACLEAR PLUS
CHANNEL
TALK
TALK
BATT LOW
ABC
JKL
DEF
IN USE
CHARGE
1
2
5
8
0
3
6
9
ABC
DEF
RDL/P
1
2
3
GHI
PRS
MNO
WXY
1
2
JKL
3
MNO
4
7
FLASH
MEM
TUV
GHI
4
PRS
5
TUV
6
WXY
TONE
OPER
*
7
8
OPER
9
MUTE
INT'COM
SPEAKER
Extend•A•Phone
SERIES
H
Q
MIC
0
PAGE
/
FIND
TONE
MEM
1
2
3
FLASH VOLUME
INT'C R.TONE R.VOL RDL/P
Contacts (On Bottom)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Charging the Battery Pack
Initial Battery Charging
The rechargeable Nickel-Cadmium battery pack must be fully charged
before using your phone for the first time. We recommend that the battery
pack charge for approximately 15-20 hours, without interruption, before
plugging the phone line into your new phone.
1.
Place the Handset on the
Base Unit. Depending on
your installation, you can
charge the Handset in the
upright position
—or—
You can charge the Handset
in its facedown position.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Make sure the CHARGE LED
lights. If the LED doesn’t
light, check to see that the
AC adapter is plugged in,
and that the Handset is
making good contact with the
Base Unit charging contacts.
ABC
JKL
DEF
IN USE
CHARGE
1
2
5
8
0
3
6
9
RDL/P
1
2
3
GHI
PRS
MNO
WXY
4
7
FLASH
MEM
TUV
TONE
OPER
*
MUTE
INT'COM
SPEAKER
Extend•A•Phone
SERIES
H
Q
PAGE
/
FIND
Continuous Battery Charging
For the best battery performance, return the Handset to the Base Unit at the
end of the day. This keeps the battery fully charged, so your phone works
best.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Low Battery Indicator
CHANNEL
TALK
When the Battery Pack in the
Handset is very low and
needs to be charged, the
TALK/BATT LOW LED flashes.
TALK
BATT LOW
ABC
2
DEF
3
1
GHI
JKL
MNO
5
TUV
4
PRS
6
WXY
8
OPER
9
7
If the TALK/BATT LOW LED begins to flash, the phone is programmed to
eliminate its functions to save power. The table below describes how to
return the Handset to normal operation.
During a Call
button operates.
In Standby Mode
Only the
None of the buttons will operate.
The Handset beeps and the
TALK/BATT LOW LED flashes once
every 3 seconds.
The Handset TALK/BATT LOW LED
flashes once every 3 seconds.
Complete your call as quickly as
possible.
You will not be able to make a call.
Return the Handset to the Base
Unit for charging.
Return the Handset to the Base
Unit for charging.
Note: Allow 15 to 20 hours without any interruption for the Handset to fully
recharge.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Tone/Pulse Switch
Be sure the TONE/PULSE switch is in the TONE position.
TONE-PULSE
Note: Most phone systems are Tone dialing. Check with your local phone
company if you are not sure whether your system is Tone or Pulse
dialing.
Adjusting Ringer/Volume Controls
The Handset and Base of the
volumes.
have controls to adjust their
Handset Volume Controls
To adjust the ringer volume
of your Handset, press
when the phone is not in use.
OPER
0
TONE
1
2
3
MEM
FLASH VOLUME
INT'C R.TONE R.VOL P
Handset Ringer Volume
Control
OPER
You can also select one of
two different ringer tones for
the Handset.
0
TONE
1
2
3
MEM
Press
to select a
FLASH VOLUME
different ringer tone when the
phone is not in use.
IR.TONE R.VOL RDL/P
Handset Ringer Tone
Select Button
27
Download from Www.Somanuals.com. All Manuals Search And Download.
To adjust the receiver
OPER
volume, press
while
0
you are on a call.
TONE
MEM
1
2
3
FLASH VOLUME
INT'C R.TONE R.VOL P
Handset Receiver Volume
Select Button
Base Volume Controls
To adjust the Base Unit
ringer volume, move the
RING-OFF LO HI switch to the
desired setting.
RING-OFF LO HI
To adjust the Base speaker
volume, slide the VOLUME
control to the desired setting.
VOLUME
VOLUM
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic Digital Code Security
Many cordless telephones operate similarly and on the same frequency.
Without digital code security, another Handset could make calls using your
Base Unit and telephone line. To avoid unauthorized calls on your phone, a
Digital Code feature was added to the
. This Digital Code is shared
only between the Handset and Base Unit. The Code is set automatically
when you first use the phone.
To reset the Digital Code, be sure the Handset is on the Base, then:
1. Press
on the Base Unit.
Note: The phone begins
ringing when is
pressed.
2. Remove the Handset from
the Base Unit, and then set it
down again. (The ringing will
stop.)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The CHARGE LED will blink to
indicate that the Digital
Security Code is set to one
of the more than 65,000
codes.
ABC
JKL
DEF
IN USE
CHARGE
1
2
5
8
0
3
6
9
RDL/P
1
2
3
GHI
PRS
MNO
WXY
4
7
FLASH
MEM
TUV
TONE
OPER
*
MUTE
INT'COM
SPEAKER
Extend•A•Phone
SERIES
H
Q
PAGE
/
FIND
If the Base Unit loses power while the Handset is off the Base, the Digital
Code may be erased. When this happens, the Handset will not function. To
establish communication between the Handset and Base Unit:
1. Remove the Handset from
the Base Unit (if it is on the
Base Unit).
30
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Restore power to the Base
Unit, and place the Handset
back on the Base Unit.
3. The CHARGE LED will blink to
indicate that the Digital
Security Code is set.
ABC
JKL
DEF
IN USE
CHARGE
1
2
5
8
0
3
6
9
RDL/P
1
2
3
GHI
PRS
MNO
WXY
4
7
FLASH
MEM
TUV
TONE
OPER
*
MUTE
INT'COM
SPEAKER
Extend•A•Phone
SERIES
H
Q
PAGE
/
FIND
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your XC3545
The
has dual keypads: one in the Handset, and one on the Base
Unit. This is like having two phones because most operations can be
performed using either the Handset or the Base Units.
Making and Receiving Calls
The following features of your
phone are different depending on
the Handset’s location when you make or receive a call.
HANDSET
BASE UNIT
1) Press
ON BASE UNIT
OFF BASE UNIT
ANSWER
CALL
Pick up Handset Press
(AutoTalk)
The speaker
LED lights.
2) Talk into the
microphone.
Note: A call
causes the
IN USE LED to
blink.
1) Pick up
Handset
1) Press
2) Listen for dial
tone
1) Press
2) Listen for dial
tone
MAKE
CALL
2) Press
3) Listen for dial 3) Dial number
tone
4) Dial number
3) Dial number
HANG
UP
Press
Press
The speaker LED
goes off.
— OR —
Return Handset to Base
(AutoStandby)
1) Pick up
Handset
1) Press
2) Listen for dial
tone
1) Press
The speaker
LED lights.
2) Listen for dial
tone
REDIAL
2) Press
3) Listen for dial 3) Press
tone
4) Press
3) Press
Note: Sometimes when you press
to hang up the phone, you may get
an error tone and the phone will not disconnect. If this happens,
place the Handset on the Base Unit or press
holding the Handset close to the Base Unit.
again while
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Channels, Hold, Mute, and Flash
To change channels, place a call on hold, mute a call, or access call waiting
while on the phone, follow these steps:
HANDSET
BASE
Press
Note: You must use the
Handset to change
channels.
CHANGING
CHANNELS
Note: Change channels to
help eliminate background
noise.
1) Press
1) Press
PLACING A
CALL ON
HOLD
Note: The phone will
begin to ring, and the
TALK/BATT LOW LED will
blink, indicating the call
is on hold.
Note: The phone will
begin to ring, and the
IN USE LED will blink,
indicating the call is on
hold.
2) Press
call.
to continue
2) Press
or
to
continue call.
MUTE
Note: You can only mute a
call while using the Base
Unit.
Press to disable the
Base Unit microphone.
The Mute LED lights.
Note: You will be able to
hear the caller, but they
will not hear you.
If the call waiting tone
Suppose the call waiting
tone sounds, press
to accept the waiting call.
sounds, press
to
accept the waiting call.
FLASH
— OR —
— OR —
If you have finished a call
and want to make another
If you have finished a call
and want to make another
call, press
to hang
call, press
to hang
up and get a dial tone.
up and get a dial tone.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Page/Intercom
The 2-Way Page/Intercom feature allows you to communicate between the
Base Unit and Handset. To use this feature remember the following:
•
•
The RING ON/BATT SAVE switch on the Handset must be in the
RING ON position.
The BASE UNIT RINGER switch must be set to either LO or HI
.
Note: If you are on a call while using the Handset and you page the Base
Unit, the Base Unit will ring even when the Base ringer switch is
set to the OFF position.
2-Way Paging
Paging the Base Unit
1. Press
Handset.
on
Note: If there is
no answer, press
again to
cancel.
3
1
2. Press
or
on Base
Unit to answer
page.
The IN USE LED
blinks and the
INT’COM LED
lights.
,
2
To end the
conversation:
3. Press
on the
Handset or
on the Base.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Paging the Handset
1. Press
Base Unit.
on the
The IN USE LED
blinks, and the
INT’COM LED
lights.
2,3
2
Note: If there is
no answer, press
again to
cancel.
2. Press
or
on the
,
Handset to
answer the page.
1,3
To end the
conversation:
3. Press
Base or
on the
on
the Handset.
Transferring a Call
When a phone call is answered at the Handset or Base, you can transfer the
call to the other station or establish 3-way calling between the Handset,
Base Unit, and the calling party.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Transferring a Call from the Handset
1. Press
Handset.
on the
The phone will
begin to ring, and
the TALK/BATT
LOW LED will
blink, indicating
the call is on hold.
Note: If there is
no answer, press
again to
cancel.
3
1
2. Press
or
on the Base
to answer the
page.
The IN USE LED
blinks, and the
INT’COM LED
lights.
,
2 4
3. Announce there
is a call waiting,
and press
to transfer.
Note: If you
press
again, then 3-way
calling begins.
To end the
conversation
4. After a call is
transferred, press
to end the
call.
Note: To end a
3-way call, press
on the
Handset and
on the Base.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Transferring a Call from the Base
1. Press
Base.
on the
The phone will
begin to ring, and
the IN USE LED
will blink,
indicating the call
is on hold.
Note: If there is
no answer,
press
to cancel.
again
4
2
2. Press
or
on the
Handset to
answer the page.
3. Announce there
is a call waiting,
and press
,
1,3
or
to
transfer.
Note: If you
press
now,
then a 3-way
calling begins.
To end the
conversation
4. After a call is
transferred,
press
the call.
to end
Note: To end a
3-way call, press
on the Base
and
Handset.
on the
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Room Monitor Feature
Another use of the
is to monitor activity near the Base Unit. To turn
the monitor on, follow the steps below.
1. Press
Handset.
on the
on the
2. Press
Handset.
2,3
1
Note: Using the Handset, you
should now be able
to monitor the room
where the Base Unit
is located.
To turn the monitor off:
,
3. Press
Handset.
on the
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming your Phone
For convenience, both the Handset and Base units have ten memory
locations, so you can store the numbers you use most often in either place.
Just remember that all programming must be completed when your phone is
in the standby mode, since the programming keys will not function while you
are on the phone.
Storing a Number in Memory
Handset Operation
CHANNEL
TALK
Use these keys
to store a
TALK
BATT LOW
number in
ABC
2
DEF
3
memory with the
Handset.
1
GHI
JKL
MNO
Note: An error
tone will sound
and the
5
4
6
PRS
TUV
WXY
8
OPER
9
7
programming
procedure will be
cancelled if more
than 20 seconds
elapses between
each keystroke
entry or step.
0
TONE
MEM
1
2
3
FLASH VOLUME
INT'C R.TONE R.VOL RDL/P
1. Remove the Handset from
the Base Unit.
CHANNEL
TALK
2. Press
.
TALK
The TALK/BATT LOW LED
BATT LOW
blinks.
ABC
2
DEF
3
1
GHI
JKL
MNO
5
TUV
4
PRS
6
WXY
8
OPER
9
7
3. Enter the number you want
to store (up to 16 digits).
5551212
39
Download from Www.Somanuals.com. All Manuals Search And Download.
4. If a pause is needed during
dialing to access a long
distance service, press
.
9R5551212
Note: The
button counts as one digit. Pressing
more than
once increases the length of the pause between numbers.
5. Press again.
6. Enter the memory location
(0-9).
A tone indicates that the
number is stored.
CHANNEL
,
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Base Operation
Use these keys to store
a number in memory
with the Base Unit.
Note: An error tone will
sound and the
VOICE SCRAMBLE
ABC
JKL
DEF
IN USE
CHARGE
1
2
5
8
0
3
6
9
programming
RDL/P
1
2
3
GHI
PRS
MNO
WXY
4
7
procedure will be
cancelled if more than
20 seconds elapses
between each
FLASH
MEM
TUV
TONE
OPER
*
MUTE
INT'COM
SPEAKER
Extend•A•Phone
SERIES
keystroke entry or step.
H
Q
PAGE
/
FIND
1. Press
.
The IN USE LED blinks.
ABC
JKL
DEF
IN USE
CHARGE
1
2
5
8
0
3
6
9
RDL/P
1
2
3
GHI
MNO
WXY
4
FLASH
MEM
PRS
TUV
7
TONE
OPER
*
MUTE
INT'COM
SPEAKER
Extend•A•Phone
SERIES
H
Q
PAGE
/
FIND
2. Enter the number you want
to store (up to 16 digits).
3. If a pause is needed during
dialing to access a long
distance service, press
.
Note: The
button counts as one digit. Pressing
more than
once increases the length of the pause between numbers.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press
again.
5. Enter the memory location
(0-9).
A tone indicates that the
number is stored.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing a Tone/Pulse Number With a Pulse Dial System
If your phone is set up for pulse dialing, you can store a mixed mode number
so that you can easily access long distance services.
Handset Operation
CHANNEL
TALK
Use these keys
to store a mixed
mode number in
memory with the
Handset.
TALK
BATT LOW
ABC
2
DEF
3
1
GHI
JKL
MNO
Note: An error
tone will sound
and the
5
4
6
PRS
TUV
WXY
8
OPER
9
7
programming
procedure will be
cancelled if more
than 20 seconds
elapses between
each keystroke
entry or step.
0
TONE
MEM
1
2
3
FLASH VOLUME
INT'C R.TONE R.VOL RDL/P
1. Remove Handset from the
Base Unit.
CHANNEL
TALK
2. Press
.
TALK
The TALK/BATT LOW LED
BATT LOW
blinks.
ABC
2
DEF
3
1
GHI
JKL
MNO
5
TUV
4
PRS
6
WXY
8
OPER
9
7
3. Enter the number to be
dialed in pulse mode.
5551212
43
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press TONE on the Handset.
PRS
TUV
WXY
8
OPER
9
7
0
TONE
MEM
1
2
3
FLASH VOLUME
INT'C R.TONE R.VOL RDL/P
5. Enter the number to be
dialed in tone mode.
3300
6. If a pause is needed during
dialing to access a long
distance service, press
.
R3300
Note: The
button counts as one digit. Pressing
more than
once increases the length of the pause between numbers.
7. Press again.
8. Enter the memory location
(0-9).
A tone indicates that the
number is stored.
CHANNEL
,
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Base Operation
Use these keys to store
a mixed mode number
in memory with the
Base Unit.
VOICE SCRAMBLE
ABC
JKL
DEF
Note: An error tone will
sound and the
IN USE
CHARGE
1
2
5
8
0
3
6
9
RDL/P
1
2
3
GHI
PRS
MNO
WXY
4
7
programming
FLASH
MEM
TUV
procedure will be
cancelled if more than
20 seconds elapses
between each
TONE
OPER
*
MUTE
INT'COM
SPEAKER
Extend•A•Phone
SERIES
H
Q
PAGE
/
FIND
keystroke entry or step.
1. Press
.
The IN USE LED blinks.
ABC
JKL
DEF
IN USE
CHARGE
1
2
5
8
0
3
6
9
RDL/P
1
2
3
GHI
MNO
WXY
4
7
FLASH
MEM
PRS
TUV
TONE
OPER
*
MUTE
INT'COM
SPEAKER
Extend•A•Phone
SERIES
H
Q
PAGE
/
FIND
2. Enter the number to be
dialed in pulse mode.
3. Press TONE on the Base Unit.
ABC
DEF
IN USE
CHARGE
1
2
5
8
0
3
RDL/P
FLASH
MEM
1
GHI
PRS
JKL
TUV
MNO
WXY
4
7
6
9
2
3
TONE
OPER
*
MUTE
INT'COM
SPEAKER
Extend•A•Phone
SERIES
H
Q
PAGE
/
FIND
45
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Enter the number to be
dialed in tone mode.
5. If a pause is needed during
dialing to access a long
distance service, press
.
Note: The
button counts as one digit. Pressing
more than
once increases the length of the pause between numbers.
6. Press again.
7. Enter the memory location
(0-9).
A tone indicates that the
number is stored.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing One-Touch Dialing Numbers
The Handset and Base both have three One Touch memory locations, so
you have easy access to emergency numbers or the numbers you call most.
Handset Operation
CHANNEL
Use these keys
to store a
TALK
TALK
BATT LOW
number in a One
Touch dialing
button with the
Handset.
ABC
2
DEF
3
MNO
1
GHI
JKL
5
4
6
Note: An error
tone will sound
and the
PRS
TUV
WXY
8
OPER
9
7
programming
0
procedure will be
cancelled if more
than 20 seconds
elapses between
each keystroke
entry or step.
TONE
MEM
1
2
3
FLASH VOLUME
INT'C R.TONE R.VOL RDL/P
1. Remove the Handset from
the Base Unit.
CHANNEL
TALK
2. Press
.
TALK
The TALK/BATT LOW LED
BATT LOW
blinks.
ABC
2
DEF
3
1
GHI
JKL
MNO
5
TUV
4
PRS
6
WXY
8
OPER
9
7
3. Enter the number you want
to store (up to 16 digits).
5551212
47
Download from Www.Somanuals.com. All Manuals Search And Download.
4. If a pause is needed during
dialing to access a long
distance service, press
.
9R5551212
Note: The
button counts as one digit. Pressing
more than
once increases the length of the pause between numbers.
5. Press again.
6. Now press the One Touch
dialing button ( , or ) you
want to program.
1
,
2
3
A tone indicates that the
number is stored.
CHANNEL
,
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Base Operation
Use these keys to store
a number in a One
Touch dialing button
with the Base Unit.
ABC
JKL
DEF
Note: An error tone will
sound and the
IN USE
CHARGE
1
2
5
8
0
3
6
9
RDL/P
1
2
3
GHI
PRS
MNO
WXY
4
7
programming
FLASH
MEM
TUV
procedure will be
cancelled if more than
20 seconds elapses
between each
TONE
OPER
*
MUTE
INT'COM
SPEAKER
Extend•A•Phone
SERIES
H
Q
keystroke entry or step.
PAGE
/
FIND
1. Press
.
The IN USE LED blinks.
ABC
JKL
DEF
IN USE
CHARGE
1
2
3
6
9
RDL/P
1
2
3
GHI
MNO
WXY
4
7
5
8
0
FLASH
MEM
PRS
TUV
TONE
OPER
*
MUTE
INT'COM
SPEAKER
Extend•A•Phone
SERIES
H
Q
PAGE
/
FIND
2. Enter the number you want
to store (up to 16 digits).
3. If a pause is needed during
dialing to access a long
distance service, press
.
Note: The
button counts as one digit. Pressing
more than
once increases the length of the pause between numbers.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press
again.
5. Now press the One Touch
dialing button ( or ) you
1
,
2
3
want to program.
A tone indicates that the
number is stored.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Dialing a Stored Number
Handset Operation
To dial a number previously stored in memory using the Handset, follow
these steps:
MEMORY
ONE TOUCH KEYS
Remove the Handset from the
Base Unit.
Remove the Handset from the
Base Unit.
Press
Press
Press
Press the One Touch dialing
button (
1
,
2
or 3) you want dialed.
Press the memory location number
(0-9) you want dialed.
Base Operation
To dial a number previously stored in memory using the Base Unit, follow
these steps:
MEMORY
ONE TOUCH KEYS
Press
Press
The speaker LED lights.
The speaker LED lights.
Press
Press the One Touch dialing
button (
1
,
2
, or 3) you want dialed.
Press the memory location number
(0-9) you want dialed.
Chain Dialing
On certain occasions, after dialing a number, you may be requested by the
party or service you are calling to enter a special access code, such as when
performing a banking transaction. To do this, simply:
1. Store the access code into a memory location.
2. Dial the main number.
3. At the appropriate time, press either the One Touch Dialing button or
press
is saved.
followed by the memory location number where the number
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Erasing a Stored Number
To erase a number previously stored in a memory location or in One Touch
memory, follow these steps:
HANDSET
BASE UNIT
Remove the Handset from the
Base Unit.
Press
twice.
Press
twice.
Press the memory location number
(0-9) or the One Touch dialing
Press the memory location number
(0-9) or the One Touch dialing
button (
button (
1
,
2
or 3) you want to clear.
1
,
2
or 3) you want to clear.
Note: An error tone will sound and the erase procedure will be cancelled if
more than 20 seconds elapses between each keystroke entry or
step.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If your
Cordless Telephone is not performing to your
expectations, please try these simple steps. If you are still unable to resolve
the problems, contact Uniden Customer Service at (800) 297-1023, 8:00
a.m. to 5:00 p.m. EST, Monday through Friday.
Problem
Suggestion
Charge light won’t come on when Handset
is placed in Base Unit.
• Make sure AC Adapter is plugged into the
Base Unit and wall outlet.
• Make sure Handset is properly seated in
Base Unit.
• Make sure that the charging contacts on
the Handset and Base Unit are clean.
Audio sounds weak and/or scratchy.
Can’t make or receive calls.
• Make sure that the Base Unit antenna is
fully extended and vertical.
• Move the Handset and/or Base Unit to
different locations and try again.
• Press the CHAN button to select another
channel.
• Check both ends of the Base Unit
telephone line cord.
• Make sure the AC Adapter is plugged into
the Base Unit and wall outlet.
• Disconnect the AC Adapter for a few
minutes, and then reconnect it.
Handset doesn’t ring or receive a page.
• Nickel-Cadmium battery pack may be
weak. Charge the battery on the Base
Unit for 15 – 20 hours.
• Set the RING ON/BATT SAVE switch on the
Handset to RING ON
.
• Extend the Base Unit antenna vertically.
• The Handset may be too far away from
the Base Unit.
• Place the Base Unit away from noise
sources.
• The Digital Security Code may be erased.
Set the Digital Code.
Base Unit doesn’t ring or receive a page.
• Set the Base Unit Ringer switch to LO or
HI.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
General – The
complies with FCC Part 15 and 68
Frequency Control
Modulation
Crystal controlled transmission
FM
Operating Temperature
– 10° to 50° C
Base Unit
Receive Frequency
Transmit Frequency
Power Requirements
Size
48.76 to 49.99 MHz (25 Channels)
43.72 to 46.97 MHz (25 Channels)
120V AC 60 Hz
7 34 in (W) x 5 17 in (D) x 1 78 in (H)
32
Weight
Approx. 15.7 oz.
Handset
Receive Frequency
Transmit Frequency
Power Requirements
Size
43.72 to 46.97 MHz (25 Channels)
48.76 to 49.99 MHz (25 Channels)
Rechargeable Ni-Cd Battery Pack
3
11
3
2
16 in (W) x 2 in (D) x 12 32 in (H) (w/
16
antenna)
Weight
Battery
Approx. 10 oz. (including battery)
BT-185
Capacity
270 mAh, 3.6V
Talk Mode
Standby Mode
6 hours
7 days
Battery Save Mode 5 weeks
Specifications, Features, and availability of Optional Accessories are all
subject to change without prior notice.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
®
XC3545
Cordless Telephone
,
UDZZ01323ZZ
Operating Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
Before you read anything else,
please observe the following:
WARNING!
Uniden America Corporation DOES NOT represent this unit to be waterproof.
To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT
expose this unit to rain or moisture.
RECHARGEABLE NICKEL-CADMIUM
BATTERY WARNING
This equipment contains a Rechargeable Nickel-Cadmium
Battery.
Cadmium is a chemical known to the State of California to
cause cancer.
The Rechargeable Nickel-Cadmium Battery contained in this
equipment may explode if disposed of in a fire.
Do not short circuit the battery.
Do not charge the Rechargeable Nickel-Cadmium Battery
used in this equipment in any charger other than the one
designed to charge this battery as specified in this Guide .
Using another charger may damage the battery, or cause
the battery to explode.
RECHARGEABLE NICKEL-CADMIUM
BATTERIES MUST BE RECYCLED OR DISPOSED
OF PROPERLY
Residents Of Minnesota should contact 1-800-225-PRBA for
information concerning reclamation and disposal of
Rechargeable Nickel-Cadmium batteries.
Residents outside of Minnesota should contact their local
authorities for information concerning reclamation and
disposal of Rechargeable Nickel-Cadmium batteries.
Download from Www.Somanuals.com. All Manuals Search And Download.
Handset Controls and Keys
1. Antenna
2. Talk/Battery Low
1
Indicator
3. Talk Button
4. Numeric Keypad
5. Tone Button
6. Memory
Programming
Button
7. Intercom Button
2
3
9
RING
ON
CHANNEL
8. Flash
/Ringer
TALK
TALK
Tone Select Button
BATT LOW
ABC
2
DEF
3
BATT
SAVE
9. Channel Select
1
Button
GHI
JKL
MNO
10
10. Ring On/Battery
5
TUV
4
PRS
6
WXY
Save Switch
4
11. One Touch Dialing
8
OPER
9
7
Buttons
0
12. Redial/Pause
5
6
7
TONE
MEM
Button
1
2
3
11
12
13. Volume
Ringer Volume
Select Button
/
FLASH VOLUME
INT'C R.TONE R.VOL RDL/P
8
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Base Unit Controls and Keys
1
2
3
4
5
6 7 8
9
10
25 CHANNEL ULTRACLEAR PLUS
ABC
JKL
DEF
IN USE
CHARGE
1
2
5
8
0
3
6
9
VOLUME
GHI
PRS
MNO
WXY
RDL/P
1
2
3
4
7
TUV
FLASH
MEM
OPER
TONE
11
*
MUTE
INT'COM
SPEAKER
Extend•
A
•Phone
H
Q
SERIES
MIC
PAGE
/
FIND
18
16
14
15
19
13
17
12
1. Base Ringer Switch
11. Numeric Keypad
12. Speaker Button
13. Intercom Button
2. Tone/Pulse Switch
with LED
with LED
3. Telephone Line Jack
4. DC Power Jack
5. Handset Retainer
6. Base Unit Antenna
7. In Use LED
8. Charge LED
9. Built-in Speaker
10. Speaker Volume Control
14. One Touch Dial Buttons
15. Mute Button
16. Memory Programming Button
17. Flash Button
18. Redial/Pause Button
19. Microphone
with LED
Download from Www.Somanuals.com. All Manuals Search And Download.
One Year Limited Warranty
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original
retail owner, this Uniden Product to be free from defects in materials and
craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate
and be of no further effect 12 months after the date of original retail sale. The
warranty is invalid if the Product is (A) damaged or not maintained as
reasonable or necessary, (B) modified, altered, or used as part of any
conversion kits, subassemblies, or any configurations not sold by Uniden,
(C) improperly installed, (D) serviced or repaired by someone other than an
authorized Uniden service center for a defect or malfunction covered by this
warranty, (E) used in any conjunction with equipment or parts or as part of
any system not manufactured by Uniden, or (F) installed or programmed by
anyone other than as detailed by the Operating Guide for this product.
STATEMENT OF REMEDY: In the event that the product does not conform
to this warranty at any time while this warranty is in effect, warrantor will
repair the defect and return it to you without charge for parts, service, or any
other cost (except shipping and handling) incurred by warrantor or its
representatives in connection with the performance of this warranty. THE
LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE
WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND
EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE
WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY
OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR
PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion
or limitation of incidental or consequential damages so the above limitation
or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state. This warranty is
void outside the United States of America.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If,
after following the instructions in this Operating Guide you are certain that
the Product is defective, pack the Product carefully (preferably in its original
packaging). Include evidence of original purchase and a note describing the
defect that has caused you to return it. The Product should be shipped
freight prepaid, by traceable means, or delivered, to warrantor at:
Uniden America Corporation
Parts and Service Division
8707 North By Northeast Blvd.
P.O. Box 501368
Indianapolis, IN 46250
(800) 297-1023, 8 AM to 5 PM EST, Monday through Friday
Download from Www.Somanuals.com. All Manuals Search And Download.
Covered under one or more of the following U.S. patents:
4,511,761
4,595,795
4,523,058
4,797,916
®
©1995 Uniden America Corporation. All rights reserved.
Printed in Hong Kong
Download from Www.Somanuals.com. All Manuals Search And Download.
|