Top Vent
Direct Vent Models
DBT33
DBT36
DBT39
INSTALLATION INSTRUCTIONS & HOMEOWNER'S MANUAL
WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
FOR YOUR SAFETY
WHAT TO DO IF YOU SMELL GAS:
* Do not try to light any appliance.
* Do not touch any electric switch
* Do not use any phone in your building.
* Immediately call yourgas supplier from
your neighbours phone. Follow the gas
suppliers instructions.
FOR YOUR SAFETY
DO NOT STORE
OR USE GASOLINE OR OTHER
FLAMMABLE VAPOURS AND/OR
LIQUIDS IN THE VICINITY OF THIS OR
ANY OTHER APPLIANCE.
Installation and service must be performed
by a qualied installer, service agency or
your gas supplier.
* If you cannot reach your gas supplier
call the re department
10002789
08/00 Rev. 0
INSTALLER: DO NOT DISCARD THIS MANUAL - LEAVE FOR HOMEOWNER
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION & OPERATING INSTRUCTIONS
This gas replace should be installed by a qualied installer
This appliance has been approved for
after-market mobile home installations
in accordance with local building codes and with current CAN
/CGA-B149 (. 1 or .2) Installation codes for Gas Burning
Fireplaces and Equipment.
FOR U.S.A Installations follow local codes and/or the current
National Fuel Gas Code. ANSI Z223.1.
FOR SAFE INSTALLATION AND OPERATION PLEASE
NOTE THE FOLLOWING:
1. This replace gives off high temperatures and should be
located out of high trafc areas and away from furniture
and draperies.
2. Children and adults should be alerted to the hazards of the
high surface temperatures of this replace and should stay
away to avoid burns or ignition of clothing.
3. Caution, due to high glass surface temperature children
should be carefully supervised when they are in the same
room as the replace.
4. Under no circumstances should this replace be modied.
Parts removed for servicing should be replaced prior to
operating the replace again.
5. Installation and any repairs to this replace should be
carried out by a qualied service person. A professional
service person should be contacted to inspect this replace
annually. Make it a practice to have all of your gas re-
places checked annually. More frequent cleaning may
be required due to excess lint and dust from carpeting,
bedding material, etc.
IMPORTANT:
PLEASE REVIEW THE FOLLOWING CAREFULLY
Remove any plastic from trim parts before turning the re-
place ON.
It is normal for replaces fabricated of steel to give off
some expansion and/or contraction noises during the start
up or cool down cycle. Similar noises are found with your
furnace heat exchanger or car engine.
It is not unusual for your gas replace to give off some
odour the rst time it is burned. This is due to the curing
of the paint and any undetected oil from the manufacturing
process.
Please ensure that your room is well ventilated - open all
windows.
It is recommended that you burn your replace for a least
six (6) hours the rst time you use it. If the optional fan
kit has been installed, place the fan switch in the “OFF”
position during this time.
LOCATING YOUR FIREPLACE
6. Control compartments, burners and air passages in this
replace should be kept clean and free of dust and lint.
Make sure that the gas valve and pilot light are turned off
before you attempt to clean this replace.
7. The venting system (chimney) of this replace should be
checked at least once a year and if needed your venting
system should be cleaned.
8. Keep the area around your replace clear of combustible
materials, gasoline and other ammable vapour and liq-
uids. This replace should not be used as a drying rack for
clothing, nor should Christmas stockings or decorations
be hung on or around the replace.
9. Under no circumstances should any solid fuels (wood,
coal, paper or cardboard etc.) be used in this replace.
10. The ow of combustion and ventilation air must not be
obstructed in any way.
11. When the replace is installed directly on carpeting, vinyl
tile or any combustible material other than wood, the
replace must be installed on a metal or wood panel
extending the full width and depth of the replace.
12. This replace must not be connected to a chimney ue
serving a separate solid fuel burning replace.
13. When the replace is not in use it is recommended that the
gas control valve be left in the OFF position.
Fig. 1
A - Flat on the wall
C - * Island
E - ** Flat on wall (in corner)
B - Cross Corner
D - ** Room Divider
F - Chase Installation
*
Island (C) and Room Divider (D) installation is possible
as long as the horizontal portion of the vent system (X)
does not exceed 20' (6.1 m). See details in the venting
section of this manual.
** When you install your replace in a Room divider (D)
or at on the wall in a corner (E), a minimum distance
of 6" (153 mm) clearance must be maintained from the
perpendicular wall and the front of the appliance. See
(Y) in Fig. 1.
10002789/0
-3-
DBT33/DBT36/DBT39
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLIANCE DIMENSIONS
Appliance Dimensions
Ref.
A
B
C
D
E
DBT33
DBT36
DBT39
838 mm (33")
733 mm (28.87")
416 mm (16.37")
787 mm (31")
559 mm (22")
356 mm (14")
810 mm (31.89")
152 mm (6")
914 mm (36")
870 mm (34.25")
533 mm (21")
838 mm (33")
610 mm (24")
406 mm (16")
946 mm (37.25")
181 mm (7.13")
171 mm (6.75")
254 mm (10")
343 mm (13.5")
991 mm (39")
870 mm (34.25")
533 mm (21")
914 mm (36")
610 mm (24")
406 mm (16")
946 mm (37.25")
190 mm (7.5")
159 mm (6.25")
213 mm (8.38")
318 mm (12.5")
F
G
H
I
149 mm (5.87")
200 mm (7.87")
297 mm (11")
J
K
Framing Dimensions
L
M
894 mm (35.18")
1264 mm (49.75")
708 mm (24.87")
368 mm (14.5")
851 mm (33.5")
737 mm (29")
1010 mm (39.75")
1403 mm (55.25")
714 mm (28.13")
419 mm (16.5")
927 mm (36.5")
889 mm (35")
1016 mm (40")
1422 mm (56")
718 mm (28.25")
419 mm (16.5")
1003 mm (39.5")
889 mm (35")
N
ROD
ROW
ROH
DBT33/DBT36/DBT39
-4-
10002789/0
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEARANCE TO COMBUSTIBLES
Appliance
Top............................. 0 mm (0")
Bottom....................... 0 mm (0")
Side............................ 0 mm (0")
Back........................... 0 mm (0")
Venting
Concentric sections of DV Vent
Top, bottom & sides .. 25 mm (1")
MANTELS
The height that a combustible mantel is tted above the re-
place is dependent on the depth of the mantel. This also applies
to the distance between the mantel leg (if tted) and the
replace.
For the correct mounting height and widths refer to Fig. 2 and
the following Mantel Charts.
HEARTH
The tting of a bay window trim kit does not effect the
distances and reference points referred to in the diagram and
chart.
Non-combustible mantels and legs may be installed at any
height and width around the appliance.
A Hearth is not mandatory but it is recommended for aesthetic
purpose. We recommend a non-combustible hearth which
projects out 12" (305 mm) or more from the front of the
replace.
When using paint or lacquer to nish the mantel, such paint or
lacquer must be heat resistant to prevent discolouration.
Cold climate Installation Recommendation:
When installing this unit against a non-insu-
lated exterior wall or chase, it is mandatory that
the outer walls be insulated to conform to appli-
cable insulation codes.
FRAMING AND FINISHING
1. Choose the unit location.
2. Place the unit into position and secure it to the oor with
1.5" (38 mm) screws, or nails. The holes to secure the
unit to the oor are located just behind the access door
grille on the left and right side of the unit.
3. Frame in the replace with a header across the top. It is
important to allow for the nished wall face when setting
the depth of the frame.
4. Attach the replace to the frame using the adjustable
frame drywall strips (located behind the access door for
shipping). Preset the depth to suit the facing material of
the wall. The strips are adjustable to 1/2"(13 mm), 5/8"
(16 mm) or 3/4" (19 mm), Fig. 3 & 4.
5. Screw through the slotted holes in the drywall strip and
into the pre-drilled holes in the replace side. Measure
from the face of the replace to the face of the drywall
strip to conrm the nal depth.
Fig. 2
10002789/0
-5-
DBT33/DBT36/DBT39
Download from Www.Somanuals.com. All Manuals Search And Download.
DBT33 / DBT36 / DBT39
CERTIFIED TO
ANSI Z21.88b-1999 / CSA Z2.33b-M99
Vented Gas Fireplace Heaters
GAS SPECIFICATIONS
Max.
Min.
Input Input
Model
Fuel Gas Control
BTU/h BTU/h
DBT33RN Nat.
DBT33RP Prop.
DBT36RN Nat.
DBT36RP Prop.
DBT39RN Nat.
DBT39RP Prop.
Millivolt
Millivolt
Millivolt
Millivolt
Millivolt
Millivolt
15,000 10,500
15,000 11,250
18,000 12,600
18,000 13,500
22,000 15,400
22,000 16,500
Fig. 3
Fig. 4
FINAL FINISHING
Non-combustible materials such as brick or tile may be
extended over the edges of the face of the appliance. DO NOT
cover any vent or grille panels.
If a Trim Kit is going to be installed on the replace, the brick
or tile will have to be installed ush with the edges of the
appliance.
GAS INLET & MANIFOLD
PRESSURES
LP (Propane)
Natural Gas
Inlet Minimum
Inlet Maximum
Manifold Pressure
4.5" WC
7" WC
11" WC
13" WC
10" WC
3.5" WC
DBT33/DBT36/DBT39
-6-
10002789/0
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS LINE INSTALLATION
REMOTE ON/OFF SWITCH
Installation
When purging the gas lines, the front glass must
be removed.
1. Thread the wiring through the holes on the end panels of
the appliance. Take care not to cut the wire or insulation
on metal edges. Route the wire to a conveniently located
receptacle box.
The gas pipeline can be brought in through the rear of the
replace as well as the bottom. Knockouts are provided on the
bottom behind the valve to allow for the gas pipe installation
and testing of any gas connection. It is most convenient to
bring the gas line in from the rear right side of the valve as
this allows fan installation or removal without disconnecting
the gas line.
2. Attach the wire to the ON/OFF switch and install the
switch into the receptacle box.
3. Connect the other ends of the wire to the gas control valve
as shown in Fig. 6.
The gas line connection can be made with properly tinned
3/8” copper tubing, 3/8” rigid pipe or an approved ex con-
nector. Since some municipalities have some additional local
codes it is always best to consult your local authority and the
CAN/CGA-B149 (.1 or .2) installation codes.
For U.S.A. Installations consult the current National Fuel Gas
Code, ANSI Z223.1
Fig. 6
Alternative Switch Location
Fig. 5
The remote switch can be installed on the front/side of the
access door. Simply mount the switch to the bracket provided
and screw the bracket to either side of the frame, lining up the
screws with the pre-punched holes, Fig. 7.
Always check for gas leaks with a mild soap and
water solution. Do not use an open ame for
leak testing.
The gas control is equipped with a captured screw type pres-
sure test point, therefore it is not necessary to provide a 1/8”
test point up stream of the control.
When using copper or ex connectors use only approved t-
tings. Always provide a union when using black iron pipe
so that the gas line can be easily disconnected for burner or
fan servicing. See the gas specication for pressure details
and ratings.
The replace valve must not be subjected to any test pressures
exceeding 1/2 p.s.i.. Isolate or disconnect this and any other
gas appliance control from the gas line when pressure testing.
Fig. 7
Do not wire the remote ON/OFF wall switch for
the gas replace to the 120 volt power supply.
10002789/0
-7-
DBT33/DBT36/DBT39
Download from Www.Somanuals.com. All Manuals Search And Download.
a) Using a suitable small screwdriver lift out the central
regulator cap from the ‘Hi - Lo’ knob on the valve.
b) Unscrew the exposed conversion screw.
c) Insert the new colour coded conversion screw. Do not
over-tighten the screw, it must be nger tight.
d) Ret the regulator cap.
e) Mount the conversion label supplied with the conver-
sion screw to the valve in a visible position.
CONVERTING THE APPLIANCE
FROM LP TO NATURAL GAS OR
NATURAL GAS TO LP.
The DBT33 is convertible between Natural Gas an LP gas
(and vice-versa) with the use of a conversion kit purchased
seperately, see your dealer for the correct part number.
The DBT36 & 39 can only be converted from
Propane to Natural gas.
10. Reassemble the replace in the reverse order, except for
the front glass. Leave this off until the unit has been
checked for leaks and the gas supply line has been bled.
11. After bleeding the gas line and checking for leaks with a
soap solution, replace the front glass. Fire up the unit,
check for ame impingement on the logs, adjusting them
if necessary. Check the manifold and supply pressures
against the appliance specications.
The conversion of this appliance from one gas
to another must be carried out by an authorized
service provider.
1. Disconnect power to the unit and shut off the gas supply.
2. Remove the glass/frame assembly.
3. Carefully remove the logs & lava rock material
4. Remove the screws that are holding the burner housing
in place.
5. Remove the burner housing. Depending on the model of
the appliance you may have to loosen the pilot bracket
retaining screw/nut to allow the pilot and bracket assem-
bly to tilt and give enough clearance to remove the burner
housing.
The procedure for converting from one gas to
another is the same regardless of the initial gas
used. The only variation is in the orice sizes
and component part numbers. Your authorized
service provider will ensure the correct parts are
used.
6. Remove the main burner orice and replace it with the
orice supplied in the conversion kit.
7. SIT Top Convertible Pilot
Gently lift off the pilot hood from the pilot. (Do not
remove the spring clip holding the hood in place). Using
a correctly sized Allen key unscrew the exposed orice.
Insert the new orice supplied in the kit, do not over
tighten the orice. Replace the pilot hood ensuring the
index tab aligns with the notch on the hood.
PSE Pilot
Using a suitable wrench on the hexagonal body unscrew
the pilot hood assembly from the pilot, do not twist the
hood itself. Remove the orice and replace it with the
new orice supplied in the kit. Ret the pilot hood
assembly. Do not over-tighten the pilot hood. The hood
must return to its original alignment. Take care not to
damage the thermocouple, thermopile or igniter.
9. SIT 820 NOVA Gas Control Valve (Fig. 9)
a) Using a Torx T20 or slotted screwdriver, remove and
save the three pressure regulator mounting screws (A),
pressure regulator tower (B) and diaphragm (C).
b) Ensure the rubber gasket (D) is properly positioned and
install the new Hi/Lo pressure regulator to the valve using
the new screws (E) supplied with the kit. Tighten screws
securely. (Reference torque - 25 in.Lb).
Fig. 9
c) Install the enclosed identication label (F) to the valve
body where it can be easily seen.
Honeywell Gas Control Valve (Fig. 10)
The Honeywell valve tted to this unit is suitable
for use with LP or Natural Gas. It is converted to
the required gas application by the installation of a
colour coded “conversion screw”.
Fig. 10
DBT33/DBT36/DBT39
-8-
10002789/0
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL VENTING INFORMATION — TERMINATION LOCATION
Do not locate termination hood where excessive snow or ice
build up may occur. Be sure to check vent termination area
after snow falls, and clear to prevent accidental blockage of
venting system. When using snow blowers, make sure snow is
not directed towards vent termination area.
Your replace is approved to be vented either through the side
wall, or vertically through the roof.
–
–
–
–
Only venting components specically approved and
labelled for this replace may be used.
Minimum clearances between vent pipes and combusti-
ble materials is one (1") inch (25 mm).
Venting terminals shall not be recessed into a wall or
siding.
Location of Vent Termination
It is imperative that the vent termination be located observing
the minimum clearances as shown on this page.
Horizontal venting must be installed on a level plane
without any incline or decline.
*Check with local codes or in absence of same with CAN/
CGA B149 (.1 or .2) Installation Codes (1991) for Canada or
for U.S.A. Installations follow the current National Fuel Gas
Code, ANSI Z223.1.
There must not be any obstruction such as bushes, garden sheds,
fences, decks or utility buildings within 24" from the front of the
termination hood.
A = clearance above grade, veranda, porch, deck, or bal-
cony [* 12 inches (305mm) minimum]
I = clearance to service regulator vent outlet [*72 inches
(1828mm) minimum]
B = clearance to window or door that may be opened [12"
(306mm)].
C = clearance to permanently closed window [minimum 12
inches (305mm) recommended to prevent condensation
on window]
J = clearance to non-mechanical air supply inlet to building
or the combustion air inlet to any other replace [ *12
inches (305mm) minimum]
K = clearance to a mechanical air supply inlet [* 72 inches
(1828mm) minimum]
D = vertical clearance to ventilated soft located above
the terminal within a horizontal distance of 24 inches
(610mm) from the centre-line of the terminal [18 inches
(458mm) minimum]
E = clearance to unventilated soft [12 inches (305mm) min-
imum].
F = clearance to outside corner see next page
G = clearance to inside corner see next page
H = * not to be installed above a meter/regulator assembly
within 36 inches (914mm) horizontally from the centre-
line of the regulator
L = † clearance above paved side-walk or a paved driveway
located on public property [*84 inches (2133mm) mini-
mum]
M = clearance under veranda, porch, deck [*12 inches
(305mm) minimum ‡]
N = Clearance above a roof shall extend a minimum of 24"
(610mm) above the highest point when it passes through
the roof surface, and any other obstruction within a
horizontal distance of 18" (450mm).
†
a vent shall not terminate directly above a side-walk or paved driveway which is located between two single
family dwellings and serves both dwellings *
‡
*
only permitted if veranda, porch, deck, is fully open on a minimum 2 sides beneath the oor *
as specied in CAN/CGA B149 (.1 or .2) Installation Codes (1991) for Canada or for U.S.A. Installations follow
the current National Fuel Gas Code, ANSI Z223.1.
Note: Local codes or regulations may require different clearances.
10002789/0
-9-
DBT33/DBT36/DBT39
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 11
Fig. 12
Fig. 13
Fig. 15
Fig. 14
DBT33/DBT36/DBT39
-10-
10002789/0
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL INFORMATION ON
HOW TO USE THE VENT GRAPH
ASSEMBLING DV COMPONENTS
The vent chart should be read in conjunction with the follow-
ing vent installation instructions to determin the relationship of
the vertical and horizontal dimensions of the vent system
1. Determine the height of the centre of the horizontal vent
pipe exiting through the outer wall. Using this dimension
on the Sidewall Vent Graph below, locate the point it
intersects with the slanted graph line.
2. From the point of this intersection, draw a vertical line to
the bottom of the graph.
3. Select the indicated dimension, and position the replace
in accordance with same.
Crimped End Pipes
Before joining elbows and pipes apply a bead of high tempera-
ture sealant to the crimped end of the elbow or pipe.
Join the pipes using a 2" (50 mm) overlap and secure the
joints with three sheet metal screws, Fig. 16. Wipe off excess
sealant.
CANADIAN INSTALLATIONS:
The venting system must be installed in accordance with the
current CAN/CGA-B149 (.1 or .2) installation code.
U.S.A. INSTALLATIONS:
The venting system must conform to local codes and/or the
current National Fuel Code ANSI Z223.1.
Only venting components manufactured by CFM Majestic Inc.
can be used in Direct Vent systems.
EXAMPLE A:
If the vertical dimension from the oor of the re
place is 11' (3.4 m) the horizontal run to the face of
the outer wall must not exceed 14' (4.3 m).
EXAMPLE B:
If the vertical dimension from the oor of the re
place is 7' (214cm), the horizontal run to the face of
the outer wall must not exceed 8-1/2' (2.6 m).
Fig. 16
Twist Lock Pipes
When using CFM Majestic Inc. Twist Lock pipe it is not
necessary to use sealant on the joints.
The only areas of the venting system that need to be sealed
with high temperature silicone sealant are the collars on the
replace and termination, and the sliding joint of any tele-
scopic vent section used in the system.
To join the twist lock pipes together, simply align the beads of
the male end with the grooves of the female end, then while
bringing the pipes together, twist the pipe until the ange on
the female end contacts the external ange on the male end.
It is recommended that you secure the joints with three sheet
metal screws however this is not mandatory with twist lock
pipe.
To make it easier to assemble the joints we suggest putting a
lubricant (Vaseline or similar) on the male end of the twist lock
pipe prior to assembly.
Fig. 17
NOTE: When a 90º elbow is installed directly to the top
collar, the max. hori zontal run is 3ft. (See Fig. 19).
10002789/0
-11-
DBT33/DBT36/DBT39
Download from Www.Somanuals.com. All Manuals Search And Download.
•
If a 90º elbow is used in the horizontal vent run (level
height maintained) the maximum horizontal vent length is
reduced by 36" (914 mm), (Fig. 20). This does not apply
if the 90º elbows are used to increase or redirect a vertical
rise (Fig. 21).
Example: According to the chart the maximum horizontal
vent length in a system with a 7.5' vertical rise is 20' (6 m)
and if a 90º elbow is required in the horizontal vent it must
be reduced to 17' (5.2 m).
VERTICAL SIDEWALL APPLICATIONS
Since it is very important that the venting system
maintain its balance between the combustion air
intake and the ue gas exhaust, certain limita-
tions as to vent congurations apply and must
be strictly adhered to.
The Vent Graph showing the relationship between vertical and
horizontal side wall venting will help to determine the various
dimensions allowable.
In Fig. 20 Dimension A plus B must not be greater than
17' (5.2 m).
Minimum clearance between vent pipes and
combustible materials is one 1"(25mm) on top,
bottom and sides unless otherwise noted.
When vent termination exits through foundations less than 20"
below siding outcrop, the vent pipe must ush up with the
siding.
It is always best to locate the replace in such a way that
minimizes the number of offsets and horizontal vent length.
The horizontal vent run refers to the total length of vent pipe
from the ue collar of the replace to the face of the outer
wall.
Horizontal plane means no vertical rise exists on this portion
of the vent assembly.
Fig. 20
•
The maximum number of 90º elbows per side wall instal-
lation is three (3).
•
•
The maximum number of 45º elbows permitted per side
wall installation is two (2). These elbows can be installed
in either the vertical or horizontal run.
For each 45º elbow installed in the horizontal run, the
length of the horizontal run MUST be reduced by 18"
(45cm). This does not apply if the 45º elbows are
installed on the vertical part of the vent system.
The maximum number of elbow degrees in a system is
270º (See Fig. 21).
•
Example: In Figure 21
Elbow 1
Elbow 2
Elbow 3
=
=
=
=
=
90º
45º
45º
90º
270º
Elbow 4
Fig. 18
Total angular variation
•
If a 90º elbow is tted directly onto the replace ange
the maximum horizontal vent run before the termination
is 36" (914 mm).
Fig. 19
Fig. 21
10002789/0
DBT33/DBT36/DBT39
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
VERTICAL SIDEWALL INSTALLATIONS
STEP 1
Locate vent opening on the wall. It may be necessary to
rst position the replace and measure to obtain hole location.
Depending on whether the wall is combustible or non-combus-
tible, cut opening to size. (Fig. 22)
(For combustible walls rst frame in opening. Fig. 22).
Fig. 24
STEP 4
Apply a bead of silicone to the inner and outer ue collars of
the replace and using three (3) screws attach an appropriate
length of vent to the replace. Follow with the installation of
the inner and outer elbow, again secure joints as described in
the section 'Joining DV Components'.
Fig. 22
STEP 5
Measure the horizontal length requirement including a 2" (50
mm) overlap, i.e. from the elbow to the outside wall face plus
2" (50 mm)(or the distance required if installing a second 90º
elbow. (Fig. 25).
COMBUSTIBLE WALLS : Cut a 9-3/8"H x 9-3/8"W (240
mm x 240 mm) hole through the exterior wall and frame as
shown (Fig. 22).
NON-COMBUSTIBLE WALLS : Hole opening should be
7.5" (190 mm) in diameter.
Always install horizontal venting on a level plane.
STEP 2
Measure wall thickness and cut zero clearance sleeve parts to
proper length (MAXIMUM 12” / 305 mm). Assemble sleeve
and attach to restop with #8 sheet metal screws (supplied).
Install restop assembly (Fig. 23).
Zero clearance sleeve is only required for combustible walls.
Fig. 23
STEP 3
Place replace into position. (Fig. 24). Measure the vertical
height (X) required from the base of the ue collars to the
centre of the wall opening.
Fig. 25
10002789/0
-13-
DBT33/DBT36/DBT39
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6
Use appropriate length of pipe sections - telescopic or xed -
and install the horizontal vent sections. The sections which go
through the wall are packaged with the starter kit, and can be
cut to suit if necessary. (Fig. 26).
Sealing vent pipe and restop gaps with high temperature
sealant will restrict cold air being drawn in around replace.
Fig. 27
Support horizontal pipes every 3' (91 cm) with
metal pipe straps.
Check replace to make sure it is levelled and
properly positioned.
BELOW GRADE INSTALLATIONS
When it is not possible to meet the required vent terminal
clearances of 12" (305mm) above grade level a snorkel vent
kit is recommended. It allows installation depth of down to
7 " (178mm) below grade level. The 7" is measured from
the centre of the horizontal vent pipe as it penetrates through
the wall.
Fig. 26
If venting system is installed below ground, we recommend a
window well with adequate and proper drainage.
STEP 7
Apply high temperature sealant to 4" (100 mm) and 7" (175
mm) collars or the termination one inch away from crimped
end. Guide the vent terminations 4" and 7" collars into their
respective vent pipes. Double check that the vent pipes over-
lap the collars by 2" (50 mm). Secure the termination to the
wall with screws provided and caulk around the wall plate
to weatherproof, Fig. 27. As an alternative to screwing the
termination directly to the wall you may also use expanding
plugs or an approved exterior construction adhesive. You may
also attach the termination with screws through the inner body
into the 4" vent pipe however for this method you must extend
the 4" pipe approximately 6" (150 mm) beyond the outer face
of the wall.
Ensure sidewall venting clearances are observed.
If installing a snorkel a minimum 24" vertical rise is necessary.
The maximum horizontal run with the 24" vertical pipe is 36"
(915mm). This measurement is taken from the collar of the
replace (or transition elbow) to the face of the exterior wall.
See the Sidewall Vent Graph for extended horizontal run if the
vertical rise exceeds 24".
1. Establish vent hole through the wall (Fig. 22.
2. Remove soil to a depth of approximately 16" below base
of snorkel. Install drain pipe. Install window well (not
supplied). Rell hole with 12" of coarse gravel leaving a
clearance of approximately 4" below snorkel. (Fig. 28)
3. Install vent system.
4. Ensure a watertight seal is made around the vent pipe
coming through the wall.
5. Apply high temperature sealant caulking (supplied)
around the 4" and 7" snorkel collars.
6. Slide the snorkel into the vent pipes and secure to the
wall.
7. Level the soil so as to maintain a 4" clearance below
snorkel. (Fig. 28)
DBT33/DBT36/DBT39
-14-
10002789/0
Download from Www.Somanuals.com. All Manuals Search And Download.
DO NOT BACK FILL AROUND SNORKEL.
A CLEARANCE OF AT LEAST 4” MUST BE
MAINTAINED BETWEEN THE SNORKEL AND
THE SOIL
VERTICAL THROUGH-THE-ROOF
APPLICATIONS.
This Gas Fireplace has been approved for,
•
Vertical installations up to 40' (12 m) in height. Up to
a 10' horizontal vent run can be installed within the vent
system using a maximum of two 90º elbows. (Fig. 30)
Fig. 28
If the foundation is recessed, use recess brackets (not supplied)
for securing lower portion of the snorkel. Fasten brackets to
wall rst and then secure to snorkel with self-drilling #8 x 1/2
sheet metal screws. It will be necessary to extend the vent
pipes out as far as the protruding wall face (Fig. 29).
Fig. 30
•
Up to two 45º elbows may be used within the horizontal
run. For each 45º elbow used on the horizontal level the
maximum horizontal length must be reduced by 18".
Example: Maximum horizontal length
0
1
2
x
x
x
45º elbows
45º elbow
45º elbows
=
=
=
10'
8.5'
7'
•
•
A minimum of an 8' vertical rise.
Fig. 29
Two sets of 45º elbow offsets within these vertical instal-
lations. From 0 to a maximum of 8' of vent pipe can be
used between elbows. (Fig. 31)
10002789/0
-15-
DBT33/DBT36/DBT39
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 32
4. Remove the two (2) screws from the top face of the bafe
assembly, Fig. 32. Place the restrictor plate as shown in
Fig. 34 and secure by retting the screws.
Fig. 33
Fig. 31
7DVCS must be used to support offsets. (Fig. 36)This
application will require that you rst determine the roof
pitch and use the appropriate starter kit. (See Venting
Components List)
•
•
The minimum height of the vent above the highest point
of penetration through the roof is 2'. See Fig. 38.
Fig. 34
VERTICAL RESTRICTOR PLATE
(DBT33 ONLY)
When installing the DBT33 with a Vertical Through-The-Roof
congured ue system the restrictor plate, (#10002495) sup-
plied with the appliance MUST BE FITTED TO THE
APPLIANCE at installation.
5. Ret the bafe assembly to the rebox, replacing the three
(3) screws and four (4) nuts.
6. Ret window glass/frame as per the appropriate sections
of this manual.
Fitting The Restrictor Plate
1. Remove the window glass/frame assembly.
2. Locate the rebox bafe assembly in the top rear area of
the rebox, Fig. 32.
3. Remove the four (4) nuts along the front edge, and the
three (3) screws along the rear edge of the bafe assembly.
Remove the bafe assembly from the rebox.
DBT33/DBT36/DBT39
-16-
10002789/0
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Install storm collar and seal around the pipe.
10. Add additional vent lengths for proper height. Fig. 38.
11. Apply high temperature sealant to 4" and 7" collars of
vertical vent termination and install.
VERTICAL THROUGH-THE-ROOF
INSTALLATION
1. Locate your replace.
2. Plumb to centre of the (4") ue collar from ceiling above
and mark position.
3. Cut opening equal to 9-3/8" x 9-3/8" (240 mm x 240 mm).
4. Proceed to plumb for additional openings through the
roof. In all cases, the opening must provide a minimum of
1 inch clearance to the vent pipe, i.e., the hole must be at
least 9-3/8" x 9-3/8" (240 mm x 240 mm).
5. Place replace into position.
6. Place restop(s) #7DVFS or Attic Insulation Shield
#7DVAIS into position and secure. (Fig. 35)
Fig. 37
Fig. 38
Fig. 35
7. Install roof support (Fig. 36) and roof ashing making
sure upper ange of ashing is below the shingles. Fig.
37.
8. Install appropriate pipe sections until the venting is above
the ashing. (See Fig. 37).
If there is a room above ceiling level, restop
spacer must be installed on both the bottom and
the top side of the ceiling joists. If an attic is
above ceiling level a 7DVAIS (Attic Insulation
Shield) must be installed.
The enlarged ends of the vent section always
face downward, Fig. 37.
Fig. 36
10002789/0
-17-
DBT33/DBT36/DBT39
Download from Www.Somanuals.com. All Manuals Search And Download.
CRIMPED END VENTING COMPONENTS
Starter Kit -Model 7DVSK - Sidewall Venting
Starter Kit - Model 7TDVSKV - Vertical Venting
for 7TDVSKV-A order 1/12 to 6/12 roof pitch
for 7TDVSKV-B order 7/12 to 12/12 roof pitch
for 7TDVSKV-F order at roof
Starter Kit - Model 7DVSKS -Snorkel Kit
for Below Grade Installation
45º elbow kit
7DVT45 for Vertical Installation Offsets
90º transition elbow kit
7DVRT90 for Vertical Sidewall Applications
or thru-the-roof.
Telescopic vent sections
7DVP610
7DVP1018
7DVP1834
7DVP3466
-
-
-
-
6" to 10" adjustable length
10" to 18" adjustable length
18" to 34" adjustable length
34" to 66" adjustable length
Pipe sections for vertical or horizontal venting
Model 7DVP8"
Model 7DVP12"
Model 7DVP24"
Model 7DVP36"
Model 7DVP48"
-
-
-
4 per box
4 per box
4 per box
Firestop Spacer
Model 7DVFS
Attic Insulation Shield
Model 7DVAIS
Vertical/Horizontal Combination Offset Support
Model 7DVCS
7DVSS Siding Shield (to protect siding)
DBT33/DBT36/DBT39
-18-
10002789/0
Download from Www.Somanuals.com. All Manuals Search And Download.
TWIST LOCK VENTING COMPONENTS
Starter Kit -Model 7TDVSK - Sidewall Venting
Starter Kit - Model 7TDVSKV - Vertical Venting
for 7TDVSKV-A order 1/12 to 6/12 roof pitch
for 7TDVSKV-B order 7/12 to 12/12 roof pitch
for 7TDVSKV-F order at roof
Starter Kit - Model 7TDVSKS -Snorkel Kit
for Below Grade Installation
45º elbow kit
7TDV45 for Vertical Installation Offsets
90º transition elbow kit
7TDV90 for Vertical Sidewall Applications
or thru-the-roof.
Telescopic vent sections
7TDVP1218 - 12" to 18" adjustable length
7TDVP3564 - 35" to 64" adjustable length
Pipe sections for vertical or horizontal venting
Model 7TDVP8"
Model 7TDVP12"
Model 7TDVP24"
Model 7TDVP36"
Model 7TDVP48"
Firestop Spacer
Model 7DVFS
Attic Insulation Shield
Model 7DVAIS
Vertical/Horizontal Combination Offset Support
Model 7DVCS
7DVSS Siding Shield (to protect siding)
10002789/0
-19-
DBT33/DBT36/DBT39
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL OPERATING INSTRUCTIONS
GLASS INFORMATION
GLASS / FRAME REMOVAL
1. Turn the replace OFF (including the pilot).
2. If the unit has been operating allow time for the compo-
nents to cool.
Only glass approved by CFM Majestic Inc.
should be used on this replace.
3. Remove the top louvre assembly.
4. Open the lower louvre panel.
•
The use of any non-approved replacement glass will void
all product warranties.
Care must be taken to avoid breakage of the glass.
Under no circumstances should this appliance be operated
without the front glass in place, or with the glass in a
damaged condition.
5. Release the two clamps securing the lower edge of the
frame by pulling down on the handles, Fig. 40.
6. Tilt the glass frame out slightly at the bottom, lift the
frame up and away rom the replace.
•
•
7. To replace the glass frame reverse the procedure.
•
Replacement glass (complete with gasket) is available
your dealer and should only be installed by a licensed
qualied service person.
GENERAL MAINTENANCE
Burner and Burner Compartment
It is important to keep the burner and the burner compartment
clean. At least once per year the logs and lava rock/ember
material should be removed and the burner compartment vacu-
umed and wiped out. Remove and ret the logs as per the
instructions in this manual.
Always handle the logs with care as they are fragile and may
also be hot if the replace has been in use.
FK24/FK12 Fan Assembly
The fan unit requires periodic cleaning. At least once per
month in the operating season open the lower louvre panels
and wipe or vacuum the area around the fan to remove any
build up of dust or lint.
Brass Trim
Clean the brass trim pieces using a soft cloth lightly dampened
with lemon oil. Do not use water or household cleaners on
any brass components.
Fig. 40
GLASS CLEANING
It is necessary to periodically clean the glass.
LOUVRE REMOVAL
The top louvre panel is removed by lifting the panel vertically
and pulling it away from the appliance, Fig. 39.
The lower access door is hinged along the bottom edge and is
folded down to allow access.
During start-up condensation, which is normal, forms on the
inside of the glass. This condensation causes lint, dust and
other airborne particles to cling to the glass surface.
Also initial paint curing may deposit a slight lm on the glass.
It is therefore recommended that the glass be cleaned two or
three times with a non-ammonia based household cleaner and
warm water (we recommend gas replace glass cleaner) within
the rst few weeks of operation.
After this initial cleaning process the glass should be cleaned
two or three times during each operating season depending on
the environment in the house.
Clean the glass after the rst two weeks of
operation.
Fig. 39
DBT33/DBT36/DBT39
-20-
10002789/0
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION OF LOGS
& LAVA ROCK
Refer to the log identication chart to identify specic log
numbers.
1. Remove the front glass / frame assembly.
2. Remove the logs from their packaging.
The logs are fragile and should be handled
with care.
Keep the packaging material out of the reach of
children and dispose of the material in a safe
manner
DBT33
Fig. 41
Fig. 42
Fig. 43
3. Place the rear log (see chart for identication number)
in the rear support channel. The at face should be at
against the rear of the rebox and the log should be central
in the channel.
4
Align the holes in the base of the left front log with the
studs on the left support bracket located over the burner
housing and place the log in position.
5. Align the holes in the base of the right front log with the
studs on the right support bracket located over the burner
housing and place the log in position.
6. Place the left top log in position by aligning the hole on
the underside of the log with the lug on the top face of
the rear log. The front end of the log rests in the cut-out
on the left front log.
7. Place the right top log in position by aligning the hole on
the underside of the log with the lug on the top face of
the rear log. The front end of the log rests in the cut-out
on the right front log.
8. Scatter the ember material over the burner housing in font
of the 2 front logs. Do not pack this material tightly,
separate it when unpacked and keep it in a loose condi-
tion.
DBT36
9. Scatter the lava rock material around the rebox base.
Do not place any of the lava rock material on
the burner housing.
DBT39
Log Identication Chart
Location
Front left
Front right
Rear
DBT33
BA2
DBT36
BB6
DBT39
BC5
BA3
BB7
BC6
BA4
BB8
BC7
Top left
Top right
BA5
BB9
BC8
BA6
BB10
BC9
10002789/0
-21-
DBT33/DBT36/DBT39
Download from Www.Somanuals.com. All Manuals Search And Download.
FLAME & TEMPERATURE
ADJUSTMENT
RN/RP & EN/EP Models
For units equipped with ‘HI/LO’ valves the ame adjustment
is accomplished by rotating the ‘HI/LO’ adjustment knob
located near the centre of the gas control valve, Fig. 44 & 45
DBT33
Fig. 47
Fig. 44
Fig. 45
DBT36
Fig. 48
FLAME CHARACTERISTICS
It is important to periodically perform a visual check of the
pilot and burner ames. Compare them to the pictorials illus-
trated below, Figs. 43 - 49.
If the ame patterns appear abnormal contact a qualied ser-
vice provider for service and adjustment.
SIT Top Convertible
DBT39
Fig. 49
SIT
Fig. 43
DBT33/DBT36/DBT39
-22-
10002789/0
Download from Www.Somanuals.com. All Manuals Search And Download.
LIGHTING AND OPERATING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING:
If you do not follow these instructions exactly, a re or explosion may
result causing property damage, personal injury or loss of life.
A. This replace has a pilot which must be lit manu-
ally.
neighbour's phone. Follow the gas supplier's
instructions.
When lighting the pilot follow these instructions
exactly.
•If you cannot reach your gas supplier, call the
Fire Department
B. BEFORE LIGHTING smell all around the re-
place area for gas. Be sure to smell next to the
oor because some gas is heavier than air and will
settle on the oor.
WHAT TO DO IF YOU SMELL GAS
•Do not try to light any replace.
•Do not touch any electric switch
•Do not use any phone in your building
•Immediately call your gas supplier from a
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, do not try to repair it, call a
qualied service technician. Applying force or any
attempted repair may result in a re or explosion.
D. Do not use this replace if any part has been under
water. Immediately call a qualied service techni-
cian to inspect the replace and to replace any part
of the control system and any gas control which has
been under water.
LIGHTING INSTRUCTIONS
10. Push the control knob all the way in and hold.
Immediately light the pilot by repeatedly depress-
ing the piezo spark ignitor until a ame appears.
Continue to hold the control knob in for about one
(1) minute after the pilot is lit. Release knob and it
will pop back up. Pilot should remain lit. If it goes
out, repeat steps 5 through 8.
1. STOP! Read the safety information above on this
page.
2. Turn off all electrical power to the replace.
3. For MN/MP/TN/TP appliances ONLY, go on to
Step 4. For RN/RP appliances turn the On/Off
switch to “OFF” position or set thermostat to lowest
level.
4. Open control access panel.
3/8" - 1/2"
5. Push in gas control knob slightly and turn clockwise
to
"OFF". Do not force.
OFF
PILOT
• If knob does not pop up when released, stop
and immediately call your service technician or gas
supplier.
• If after several tries, the pilot will not stay lit, turn
the gas control knob to "OFF" and call your service
technician or gas supplier.
EURO SIT
SIT NOVA
HONEYWELL
6. Wait ve (5) minutes to clear out any gas. Then
smell for gas, including near the oor. If you smell
gas, STOP! Follow "B" in the safety information
above on this page. If you don't smell gas, go to
the next step.
11. Replace glass door.
12. Turn gas control knob to "ON" position.
13. For RN/RP appliances turn the On/Off switch to
"ON" position or set thermostat to desired setting.
14. Turn on all electrical power to the replace.
7. Remove glass door before lighting pilot. (See Glass
Frame Removal in manual).
8. Visibly locate pilot by the main burner.
9. Turn knob on gas control counter clockwise
to "PILOT".
TO TURN OFF GAS TO FIREPLACE
1. Turn the On/Off switch to “OFF” position or set
the thermostat to lowest setting.
2. Turn off all electric power to the replace if
service is to be performed.
3. Open control access panel.
4. Push in gas control knob slightly and turn clock-
wise to "OFF". Do not force.
5. Close control access panel.
10002789/0
-23-
DBT33/DBT36/DBT39
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING THE GAS CONTROL SYSTEM
HONEYWELL MILLIVOLT VALVE
DBT33/DBT36/DBT39
-24-
10002789/0
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING THE GAS CONTROL SYSTEM
SIT NOVA 820 MILLIVOLT VALVE
Note: Before trouble shooting the gas control system, be sure external gas shut off is in the "On" position.
WARNING: BEFORE DOING ANY GAS CONTROL SERVICE WORK, REMOVE GLASS FRONT.
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
1. Spark ignitor will not light A. Defective or misaligned
electrode at pilot.
Using a match, light pilot. If pilot lights, turn off pilot and
push the red button again. If pilot will not light - check gap
at electrode and pilot-should be 1/8" to have a strong spark.
B. Defective ignitor (Push Button)
Push Piezo Ignitor Button. Check for spark at electrode and
pilot. If no spark to pilot, and electrode wire is properly
connected, replace ignitor.
2. Pilot will not stay lit after
carefully following lighting
instructions.
A. Defective pilot generator
(thermocouple), remote wall
switch.
1. Check pilot ame. Must impinge on thermocouple/
thermopile. Note: this pilot burner assembly utilizes both-
a thermocouple and a thermopile. The thermocouple
operates the main valve operation (On and Off). Clean
and or adjust pilot for maximum ame impingement on
thermopile and thermocouple.
B. Defective automatic valve
Turn valve knob to "Pilot". Maintain ow to pilot; mil
liv olt meter should read greater than 10 mV. If the reading
is okay and the pilot does not stay on, replace the gas
valve. Note: An interrupter block (not supplied) must be
used to conduct this test.
3. Pilot burning, no gas to
main burner
A. Wall switch or wires defective
Check wall switch and wires for proper connections.
Jumper wire across terminals at wall switch, if burner
comes on, replace defective wall switch. If okay, jumper
wires across wall switch wires at valve, if burner comes
on, wires are faulty or connections are bad.
B. Thermopile may not be
generating sufcient
millivoltage.
1. Be sure wire connections from thermopile at gas valve
terminals are tight and thermopile is fully inserted into pilot
bracket.
2. One of the wall switch wires may be grounded. Remove
wall switch wires from valve terminals if pilot now stays
lit, trace wall switch wiring for ground. May be grounded
to replace or gas supply.
3. Check thermopile with millivolt meter. Take reading at
thermopile terminals of gas valve. Should read 250-300
millivolts (minimum 150) while holding valve knob de-
pressed in pilot position and wall switch "Off". Replace
faulty thermopile if reading is below specied minimum
C. Plugged burner orice.
Check burner orices for debris and remove.
D. Defective automatic valve
operator.
Turn valve knob to "On", place wall switch to "On" millivolt
meter should read greater than 100 mV. If the reading is
okay and the burner does not come on, replace the gas
valve.
4. Frequent pilot outage
problem.
A. Pilot ame may be too low
or blowing (high) causing the
pilot safety to drop out.
Clean and/or adjust pilot ame for maximum ame
impingement on thermopile and thermocouple.
B. Possible blockage of the vent
terminal.
Check the vent terminal for blockage (recycling the ue gases)
10002789/0
-25-
DBT33/DBT36/DBT39
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS LIST
Items marked ‘*’ are not shown in the following parts pictorial page.
Ref. Description
DBT33
10000470
BA2
DBT36
10000023
BB6
DBT39
10000024
BC5
1
Log Set (complete)
1a Log - Front left
1b Log - Front right
1c Log - rear
1d Log - Top left
1e Log - Top right
BA3
BB7
BC6
BA4
BB8
BC7
BA5
BB9
BC8
BA6
BB10
BC9
*
*
Lava rock package
Ember material
10001454
51915
10001454
51915
10001454
51915
2a Burner housing with tiles, Nat. (Includes 2c)
2b Burner housing with tiles, Prop. (Includes 2c)
2c log support bracket - each
10002407
10002407
10002942
57803
10000031
10000032
10002942
57803
10000033
10000034
10002942
57803
*
*
Ceramic tile, single
Orice, burner, Nat and Prop.
See the rating plate for orice specications
3a Pilot assembly, SIT RN
N/A
N/A
10000674
10000675
N/A
10000674
10000675
N/A
3b Pilot assembly, SIT RP
4a Pilot assembly, SIT Top Convertible RN
4b Pilot assembly, SIT Top convertible RP
10002264
10002265
N/A
N/A
N/A
5
6
*
*
*
*
7
8
9
Pilot, SIT
10001295
N/A
10001295
N/A
Pilot,, SIT Top convertible
Pilot orice, SIT Nat.
10002266
N/A
54273
54272
N/A
54273
54272
N/A
Pilot orice, SIT Prop.
N/A
Pilot orice, SIT Top convertible Nat.
Pilot orice, SIT Top convertible Prop.
Pilot hood, SIT Top convertible
Thermocouple, RN & RP
Thermopile, RN & RP
10002268
10002269
10002385
53373
N/A
N/A
N/A
N/A
53373
51827
10001296
57318
10001297
52464
N/A
53373
51827
10001296
57318
10001297
52464
N/A
51827
10 Pilot tube (with ttings
Manifold tube (with ttings)
10001296
57318
*
11 Electrode igniter SIT (with cable), RN & RP
12 Piezo igniter, SIT 820 Valve
13 Piezo igniter, Honeywell Valve
14a Gas Valve SIT820 RN
10001297
52464
20000062
52677
52677
52678
N/A
52677
52678
N/A
14b Gas Valve SIT820 RP
52678
15a Gas Valve Honeywell RN
10001782
10001759
54103
15b Gas Valve, Honeywell RP
N/A
N/A
16 Fan assembly (with bracket) (FK24 option)
54103
51865
51704
51738
54103
51865
51704
51738
*
*
*
Electrical cord, (FK24 option).
51865
Fan temperature sensor, (FK24 option)
Fan speed control, (FK24 option)
51704
51738
DBT33/DBT36/DBT39
-26-
10002789/0
Download from Www.Somanuals.com. All Manuals Search And Download.
Ref.
Description
DBT33
51882
DBT36
51882
DBT39
51882
*
Knob, fan speed control, (FK24 option)
17 Fan assembly, with bracket (FK12 option)
18 Window frame assembly
ZA1110
10001803
10002822
57317
ZA1110
10001425
10001781
57317
ZA1110
54363
*
*
Window glass (with gasket)
Gasket (window glass)
10002821
57317
19 Clamp, window frame assembly
20 Window trim, polished brass (with magnets)
21 Top louvre assembly
54174
54174
54174
55005
57480
57483
10000292
10000293
52356
10000037
10000038
52356
10000039
10000040
52356
22 Bottom Louvre assembly
23 Hinge (bottom louvre assembly
*
*
*
Restrictor plate
10002495
51842
N/A
N/A
Remote ON/OFF switch
51842
51842
Remote switch kit (switch, wire & bracket)
53875
53875
53875
10002789/0
-27-
DBT33/DBT36/DBT39
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS PICTORIAL
DBT33/DBT36/DBT39
-28-
10002789/0
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL ACCESSORIES AVAILABLE
EB-1 ELECTRICAL BOX
The EB-1 Electrical junction box when tted and correctly
wired gives an easy and convenient power outlet for the
optioal fan kit.
If the EB-1 electrical junction box is being tted
the replace must be electrically connected and
grounded in accordance with local codes or, in
the absence of local codes, with the current CSA
C22.1 Canadian Electric Code.
For U.S.A. installations follow the local codes
and the national electrical code ANSI/NFPA No
70.
It is strongly recommended that the wiring of
the EB-1 Electrical Junction Box be carried out
be a licensed electrician.
Ensure that the power to the supply line has
been disconnected before commencing this pro-
cedure.
To install and connect the EB-1 box to the house electrical
supply follow the steps below.
1. Disconnect the power to the electrical supply line.
2. Remove the cover plate over the EB-1 knock-out the side
of the appliance, retain the screw that held the plate.
3. Remove the front cover of the EB-1 box.
4. Remove the plug socket assembly from the EB-1 box.
5. Feed the electrical supply line in through the EB-1 open-
ing in the side of the appliance and then through the back
of the EB-1 assembly, Fig ???.
FAN KITS
FK24 Fan Assembly
This auxiliary fan system increases the efciency of the circu-
lation of the heating air.
The FK24 fan kit allows variable speed control of the circula-
tion fan and also incorporates a heat sensor in the circuit.
Specications
6. Connect the ground wire of the supply line to the green
screw of the socket assembly.
115 Volt / 60 Hz / 56 Watts
7. Connect the white wire of the power line to the chrome
screw of the socket assembly.
Maintenance
The fan itself does not require regular maintenance, however
periodic cleaning of the fan and the surrounding area is
required.
8. Connect the black wire of the power supply line to the
brass screw (polarized) of the socket assembly.
9. Ret the socket assembly back into the electrical box and
replace the front cover plate. Secure the cable with the
clamp on the outside of the EB-1 base plate and ret the
EB-1 assembly to the appliance with the screw removed
in step 1.
Check the area under the control door (lower louvre assembly)
and in front of the fan and wipe or vacuum this area at least
once a month during the operating season.
Installation
The fan assembly and other components are supplied fully
wired eliminating the need for a licensed electrician to carry
out the installation
If hard wiring the fan using Method B (following) we strongly
recommend the use of a licensed electrician.
1
Open the lower Louvre assembly. Maneuver the fan &
bracket assembly around the gas valve and lines to locate
the unit onto the screw studs on the back of the replace
Install the thermal sensor under the bottom of the rebox,
locating it over the two 10 mm studs and secure it with
nuts.
2
10002789/0
-29-
DBT33/DBT36/DBT39
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Locate the fan speed control unit. This can be tted
behind the lower louvre assembly as in Fig. 50 or located
remotely in a conveniently located wall mounted electrical
box. Remote location of the speed control will require
suitable extension of the component wiring.
The power supply may be connected in 2 ways:
Method A
Route the 6' lead tted to the unit to a conveniently
located wall socket.
Method B
WIRING INSTRUCTIONS
The replace, when installed, must be electri-
cally connected and grounded in accordance
with local codes or, in the absence of local
codes, with the current CSA C22.1 Canadian
Electric Code.
For U.S.A. installations follow the local codes
and the national electrical code ANSI/NFPA No
70.
The EB1 receptacle box (Pt. # ZA1200) may be hard
wired into the house supply. The fan lead is then plugged
into the EB1 box.
Should this fan require servicing or repair the
power supply must be disconnected. For rewir-
ing of any replacement parts see Fig. 51
Any electrical re-wiring of this fan must be done
by a licensed electrician.
Method A (Not using EB1, Fig. 51)
1. Connect the ground wire of the power supply line to the
ground stud located on the base of the rebox.
2. Connect the black wire of the supply line to either termi-
nal of the speed control unit.
3. The second terminal of the speed control unit is attached
to either terminal of the thermal sensor.
Fig. 50
4. The second terminal of the thermal sensor is connected to
either terminal of the fan motor.
5. The second fan motor terminal is connected to the white
wire of the supply line.
FK12
This auxiliary fan system increases the efciency of the circu-
lation of the heating air.
The FK12 Fan Assembly is a xed speed fan system and does
not allow for variable speed control. It does not use the speed
control unit or the heat sensor used in the FK24 Kit.
Specications
115 Volts / 60 Hz / 56 Watts.
Maintenance
The fan itself does not require regular maintenance, however
periodic cleaning of the fan and the surrounding area is
required.
Fig. 51
Check the area under the control door (lower louvre assembly)
and in front of the fan and wipe or vacuum this area at least
once a month during the operating season.
Method B (Using the EB-1 Box.
For instruction on wiring the EB-1 Electrical Junction Box see
the chapter EB-1 Electrical Box.
Installation
The fan assembly is supplied fully wired eliminating the need
for a licensed electrician to carry out the installation
1. Open the lower Louvre assembly. Maneuver the fan &
bracket assembly around the gas valve and lines to locate
the unit against the back wall of the appliance, resting on
the base.
2. With the protective cover removed from the self-adhesive
‘Velcro’ strips apply mild pressure to the fan & bracket
unit to secure the strips to the metal panels. No further
securing is required.
3. Power to the fan can be supplied by plugging the supplied
lead into a conveniently located wall socket or by using a
hard-wired EB1 connector box.
DBT33/DBT36/DBT39
-30-
10002789/0
Download from Www.Somanuals.com. All Manuals Search And Download.
CERAMIC REFRACTORY KITS
Ceramic refractory panels are available in kit form for the
DBT series appliances.
Appliance Model
DBT33
Kit Name
33BDVTCR
36BDVCR
39BDVCR
DBT36
DBT39
Take care when handling the refractory panels
as they are fragile until held in place and sup-
ported.
Fig. 53
Installation, refer to Figs. 52 & 53
FRONT WINDOW SCREEN
An optional front window screen is available for the DBT
series appliances
1. Remove the front frame/glass assembly.
2. Remove the logs.
3. Place the lower supports for the side refractory panels on
the base of the rebox. Place each support so that the
slotted hole ts over the forward screw head along the
edge of the base.
4. Lay the angular base panels in place on the oor of the
rebox on either side of the burner housing
Appliance Model
DBT33
Kit Name
33BDVTKS
36BDVTKS
39BDVTKS
DBT36
DBT39
5. Loosely attach the top adjustable tabs to the studs located
in the top of the rebox toward the front corners.
6. Place the rear refractory panel in place. Locate the lower
edge of the panel in the ledge formed by the top of the rear
log support bracket.
7. Slide the side refractory panels into place to hold the rear
panel secure. Adjust the top adjustable tabs to hold the
side panel against the rebox wall and secure the tab.
Repeat the procedure on the other side.
Installation, refer Fig. 54
DO NOT ATTEMPT to install or remove the
screen while the appliance is hot.
Either remove the top and bottom brass window trims or
take care not to scratch them during the installation of the
screen kit.
1. Slide the tabs on the top edge of the window screen
assembly up into the slots in the underside of the top rail
of the window frame.
8. Replace the logs and frame/glass assembly.
For esthetic purposes we recommend lining up the horizontal
mortar lines.
2. With the tabs in the slots place the screen down against
the glass.
3. Slide the screen down the glass until the bottom edge of
the screen sits in the gap between the bottom rail of the
window frame and the window glass.
To remove the screen for glass cleaning reverse the installa-
tion procedure.
Fig. 52
Fig. 54
10002789/0
-31-
DBT33/DBT36/DBT39
Download from Www.Somanuals.com. All Manuals Search And Download.
DECORATIVE BAY WINDOWS
Bay window kits are available for the DBT33, DBT36 &
DBT39 model appliances.
When tting the Bay Window Kits the original
front frame/glass assembly MUST remain in
place. The Bay Window kit is tted over the
existing front glass.
Installation
1. Remove the upper and lower brass window trims.
2. Remove the existing bottom louvre assembly complete
with the hinges.
3. Remove the top louvre assembly
4. Assemble the Bay Window Kit according to the instruc-
tions supplied with the kit.
5. Place the 2 pieces of ceramic refractory along the base of
the bay window, Fig. 59
6. Hang the Bay Window Assembly over the existing front
frame & glass assembly.
7. Re-install the upper louvre assembly.
Do not remove the existing front frame and
glass panel.
Fig. 55
REMOTE CONTROLS
Optional remote control units are available to control different
functions of the appliance.
Model Function/s Controlled
MRC1 ON/OFF
MRC2 ON/OFF and Temperature
MRC3 ON/OFF and Temperature control with a
digital display and a programmable 24 hour
clock
IMT
Wall mounted thermostat control
DBT33/DBT36/DBT39
-32-
10002789/0
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY & EXTENDED LIFE TIME PROTECTION
For Gas Appliance Products*
BASIC WARRANTY:
GARANTIE DE BASE:
The CFM Majestic, Inc.™ (hereinafter referred to collectively as the "Company")
warrants that your new Vermont Castings Gas Appliance is free from
manufacturing and material defects for a period of one year from date of
installation, subject to the following conditions and limitations.
The CFM Majestic. Inc. (aux présentes nommée la "Société") garantit votre
nouveau foyer au gaz CFM Majestic, Inc. contre tous défauts de fabrication
et de matières premières pour une période d'un an à compter de la date
d'installation, sujet aux conditions et limitations suivantes.
EXTENDED LIFE TIME WARRANTY:
GARANTIE A VIE PROLONGEE:
The heat exchanger, combustion chamber and ceramic burner parts of every
*CFM Majestic, Inc. product are warranted for life to the original owner, subject
to proof of purchase and the following conditions and limitations:
1. This new CFM Majestic, Inc. product must be installed by a competent,
authorized service contractor. It must be installed and operated at all times in
accordance with the Installation and Operating instructions furnished with the
product. Any alteration, willful abuse, accident, or misuse of the product shall
nullify this warranty.
2. This warranty is non-transferrable, and is made to the original owner, provided
that the purchase was made through an authorized supplier of the Company.
3. This warranty is limited to the repair or replacement of part(s) found to be
defective in material or workmanship, provided that such part(s) have been
subjected to normal conditions of use and service, after said defect is confirmed
by the Company's inspection.
4. The Company may, at its discretion, fully discharge all obligations with respect
to this warranty by refunding the wholesale price of the defective part(s).
5. Any installation, labour, construction, transportation, or other related costs/
expenses arising from defective part(s), repair, replacement, or otherwise of
same, will not be covered by this warranty, nor shall the Company assume
responsibility for same. Further, the Company will not be responsible for any
incidental, indirect, or consequential damages, except as provided by law.
6. All other warranties - expressed or implied - with respect to the product, its
components and accessories, or any obligations/liabilities on the part of the
Company are hereby expressly excluded.
Les pièces de l'échangeur de chaleur, de la chambre à combustion et du brûleur
en céramique de tout produit *CFM Majestic, Inc. sont garanties pour la vie
de l'acheteur d'origine, le tout sujet à une preuve d'achat et aux conditions et
limitations suivantes:
1. Ce nouveau produit CFM Majestic, Inc. doit être installé par un entrepreneur de
service autorisé et compétent. Il doit être installé et utilisé en tout temps selon
les instructions d'installation et de fonctionnement fournies avec le produit. Toute
altération, abus volontaire, accident ou mauvais usage du produit annulera cette
garantie.
2. Cette garantie n'est pas transférable et est offerte à l'acheteur au détail d'origine,
à condition que l'achat soit effectué par l'entremise d'un détaillant autorisé de la
Société.
3. Cette garantie est limitée à la réparation ou au remplacement de(des) pièce(s)
trouvée(s) défectueuse(s) en matières premières ou main-d'oeuvre, à condition
que lesdites pièces aient été sujettes aux conditions normales d'usage et de
service, après que ledit défaut a été confirmé par une inspection par la Société.
4. La Société peut, à sa discrétion, se décharger entièrement de toutes obligations
se rapportant à cette garantie en remboursant le prix de gros de la(des) pièce(s)
défectueuse(s).
5. Tous les frais/dépenses d'installation, de main-d'oeuvre, de construction, de
transport ou autres causés par une (des) pièce(s) défectueuse(s), une réparation,
un remplacement ou autre, ne seront pas couverts sous cette garantie, et la
Société n'assume aucune responsabilité pour ceux-ci. De plus, la Société ne
pourra être tenue responsable pour tous dommages fortuits ou indirects sauf la
ou prévu par la loi.
6. Toutes autres garanties, exprimées ou sous-entendues, en ce qui a trait au
produit, ses composants et accessiores, ou toutes obligations/responsabilités de
la part de la Société sont aux présentes expressment excluses.
7. La Société n'assume et n'autorise personne à assumer, en son nom, toutes
responsabilités en ce qui a trait à la vente de ce produit CFM Majestic, Inc..
8. Les garanties, telles que décrites dans ce document, ne s'appliquent pas aux
compasants de cheminée ou aux autres accessoires non CFM Majestic, Inc.
utilisés conjointement pour l'installation de ce produit.
9. La Société n'encourrera aucune responsabilité pour . . .
a) Les refoulements de cheminées ou débordements causés par les conditions
environnementales comme par les arbres, les édifices, les toits, les côteaux
ou les montagnes adjacents.
7. The Company neither assumes, nor authorizes any third party to assume, on its
behalf, any other liabilities with respect to the sale of this CFM Majestic, Inc.
product.
8. The warranties as outlined within this document do not apply to chimney
components or other non CFM Majestic, Inc. accessories used in conjunction
with the installation of this product.
9.
The Company will not be responsible for . . .
a) Down drafts or spillage caused by environmental conditions such as near-by
trees, buildings, roof tops, hills, or mountains.
b) Inadequate ventilation or negative air pressure caused by mechanical
systems such as furnaces, fans, clothes dryers, etc.
10. This warranty is void if:
a) The fireplace has been operated in atmospheres contaminated by chlorine,
fluorine or other damaging chemicals.
b) The fireplace is subjected to prolonged periods of dampness or
condensation.
c) Any damage to the fireplace, combustion chamber, heat exchanger or other
components due to water, or weather damage which is the result of, but not
limited to, improper chimney/venting installation.
b) Une ventilation inadéquate ou une pression d'air négative causée par
des systèmes mécaniques comme les fournaises, les ventilateurs, les
sécheuses, etc.
10. Cette garantie est nulle si:
a) Le foyer a été utilisé dans une atmosphère contaminée par du chlore, du
fluor ou tous autres produits chimiques.
d) Any alteration, willful abuse, accident, or misuse of the product.
b) Le foyer est assujetti à de longues périodes d'humidité ou de condensation.
c) Des dommages sont causés au foyer, à la chambre de combustion. à
l'échangeur de chaleur ou aux autres composants par de l'eau ou par la
température qui est le résultat mais sans y être limité, d'une mauvaise
installation de cheminée/ventilation.
GLASS DOORS & BRASS PLATED PARTS
Glass doors are not warranted for breakage due to misuse or accident.
Brass parts should be cleaned with lemon oil only. Brass cleaners cannot be used.
Mortar mix and masonry cleaners may corrode the brass finish. The Company will
not be responsible for, nor will it warrant any brass parts which are damaged by
external chemicals or down draft conditions.
d) Toute altération, abus volontaire, accident ou mauvais usage du produit
annulera cette garantie.
IF WARRANTY SERVICE IS NEEDED . . .
PORTES EN VERRE & PIECES PLAQUEES LAITON
Les portes en verre ne sont pas garanties contre le bris causé par un mauvais usage
ou un accident.
Les pièces en laiton devraient être nettoyées qu'avec de l'essence de citron. Les
nettoyeurs de laiton ne peuvent pas être utilisés. La Société ne sera pas responsable
pour, et ne garantit pas les pièces en laiton qui sont endommagées par des conditions
chimiques externes ou de refoulement.
1) Contact your supplier. Make sure you have your warranty, your sales receipt,
and the model/serial number of your CFM Majestic, Inc. product.
2) DO NOT ATTEMPT TO DO ANY SERVICE WORKYOURSELF.
SI UN SERVICE SOUS GARANTIE EST REQUIS . . .
1. Communiquez avec votre détaillant. Assurez-vous que vous avez votre garantie,
votre reçu de caisse ainsi que le numéro de modèle/série de votre produit CFM
Majestic, Inc.
2. NE TENTEZ PAS D'EFFECTUER DES REPARATIONS VOUS-MEME.
CFM Majestic, Inc.
© Copyright
CFM Majestic, Inc.
410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7885
DBT33/DBT36/DBT39
10002789/0
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Thermador Dishwasher P24 User Manual
Toro Swimming Pool Filter MODEL 08703 User Manual
Toshiba Webcam satellite p100 User Manual
Trango Broadband Network Router High Density Mesh System User Manual
Triarch Indoor Furnishings 29274 User Manual
Tripp Lite Network Card SR1UPANEL10 User Manual
Tripp Lite TV Cables B126 002 User Manual
Viking Coffeemaker VCCM12 User Manual
Viking Range DSC5486 User Manual
Vizio Car Satellite TV System E320 B0 User Manual