INSTALLER / CONSUMER
SAFETY INFORMATION
Please read this manual
before installing and using
appliance.
Unvented
Gas-Fired Room Heater
Blue Flame Heaters
WARNING: If the information in
this manual is not followed
exactly, a fire or explosion may
result causing property damage,
personal injury of loss of life.
Models:
VCBV30TN, VCBV30TP - 30,000 Btu/Hr Thermostat
VCBV20TN, VCBV20TP - 20,000 Btu/Hr Thermostat
VCBV10TN, VCBV10TP - 10,000 Btu/Hr Thermostat
• Do not store or use gasoline or
other flammable vapors and liquids in
the vicinity of this or any appliance.
• WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance
• Do not touch any electrical switch;
do not use any phone in your building
VERMONT
C
astings
• Immediately call your gas supplier
form a neighbor’s phone. Follow the
gas supplier’s instructions
• If you cannot reach your gas
Plaque Heaters
supplier, call the fire department
Models:
VCPV30TN, VCPV30TP - 30,000 Btu/Hr Thermostat
VCPV18TN, VCPV18TP - 18,000 Btu/Hr Thermostat
VCPV10TN, VCPV10TP - 10,000 Btu/Hr Thermostat
• Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
Installer: Leave this manual
with the consumer.
Consumer: Retain this
manual for future reference.
VERMONT
C
astings
User’s Operation and Installation Manual
20003770 8/02 Rev. 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Verm ont Castings VCBVTN/TP & VCPVTN/TP Room Heater
VCBVTN, VCBVTP, VCPVTN and VCPVTP Specifications
Input Rating
(Btu/Hr) Variable
Regulator
Pressure
Setting
Inlet Gas Supply
Pressure
Size
of Heater
Gas
Weight
Models
Type
Min.
Max.
Min.
Max.
VCBV30TN
VCBV20TN
VCBV10TN
VCBV30TP
VCBV20TP
VCBV10TP
VCPV30TN
VCPV18TN
VCPV10TN
VCPV30TP
VCPV18TP
VCPV10TP
15,000 30,000
27” x 24” x 8⁵⁄₈”
30 lbs.
22 lbs.
17 lbs.
30 lbs.
22 lbs.
17 lbs.
30 lbs.
22 lbs.
17 lbs.
30 lbs.
22 lbs.
17 lbs.
Natural 10,000 20,000
5,000 10,000
3.0” w.c.
4.0” w.c. 10.5” w.c. 19³⁄₈” x 22⁷⁄₈” x 8¹⁄₂”
15¹⁄₂” x 20⁷⁄₁₆” x 7⁷⁄₈”
15,000 30,000
27” x 24” x 8¹⁄₂”
LP
Natural
LP
10,000 20,000
5,000 10,000
6,400 30,000
6,400 18,000
5,500 10,000
6,400 30,000
6,400 18,000
5,500 10,000
8.0” w.c. 11.0” w.c. 14.0” w.c. 19³⁄₈” x 22⁷⁄₈” x 8¹⁄₂”
15¹⁄₂” x 20⁷⁄₁₆” x 7⁷⁄₈”
27” X 24” X 8⁵⁄₈”
6.0” w.c.
4.0” w.c. 10.5” w.c. 19³⁄₈” x 22⁷⁄₈” x 8¹⁄₂”
15¹⁄₂” x 20⁷⁄₈” x 7⁷⁄₈”
27” x 24” x 8¹⁄₂”
10.0” w.c. 11.0” w.c. 14.0” w.c. 19³⁄₈” x 22⁷⁄₈” x 8¹⁄₂”
15¹⁄₂” x 20⁷⁄₈” x 7⁷⁄₈”
NOTES: For altitudes above 2,000 feet, reduce the input ratings (Btu/Hr) 4% for each 1,000 feet above sea level.
DO NOT USE THIS HEATER AT AN ELEVATION ABOVE 4,500 FEET.
Combination
Gas Control
Front
Panel
Combination
Gas Control
Front
Panel
Frame
Body
Assembly
Grille
Guard
Frame
Body
Assembly
Grille
Guard
VERMONT
C
astings
3771
3770
Fig. 1 Product identification.
Local Codes
Product Features
Safety Device
VCBV30 / VCBV20 / VCBV10
VCPV30 / VCPV18 / VCPV10
This heater has a pilot with an Oxygen Depletion
Sensor shutt-off system (ODS). The ODS pilot is a
Certified to
required feature for vent-free heaters. The ODS pilot
shuts off the heater if the normal air oxygen content is
reduced to 18%.
ANSI Z21.11.2b-2002 Unvented Heaters
Install and use heater with care. Follow all local codes.
In the absence of local codes, use the latest edition of
the National Fuel Gas Code ANSI Z223.1, also know as
NFPA54.
Piezo Ignition System
This heater has a piezo ignitor. This system requires no
matches, batteries or other sources to light the heater.
Available from:
American National
Standards Institute, Inc.
1430 Broadway
National Fire Protection
Association, Inc.
Batterymarch Park
Quincy, MA 02269
Thermostatic Heat Control
Thermostat has a sensing bulb, and a control valve
resulting in greatest heat comfort and possible lower
heating bills.
New York, NY 10018
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Verm ont Castings VCBVTN/TP & VCPVTN/TP Room Heater
In s t a lla t io n
For proper operation of the unit, provide fresh air
Installation Requirements
Fresh Air for Combustion and Ventilation
WARNING:
opening(s) to the room. Follow the National Fuel Code
NFPA54/ANSI Z223.1, for required size of combustion
and ventilation openings.
NOTICE: A qualified service technician should install
heater. Follow all local codes.
This heater must have fresh air for proper opera-
tion. If not, poor fuel combustion could result.
Read the following instructions to insure proper
fresh air for this and other fuel-burning appli-
ances in your home.
Gas Type
Verify the type of gas supply to be used, either natural
gas or LP (Propane), and make sure the marking on the
appliance rating plate agrees with that of the supply
gas. The rating plate is located on the side of the
heater, which indicates the type of gas that the heater is
orificed for.
Modern construction standards have resulted in homes
that are highly energy-efficient and that allow little heat
loss. Your home needs to breathe, however, and all
fuel-burning appliances need fresh air to function
properly and safely. Exhaust fans, clothes dryers,
fireplaces and other fuel burning appliances all use the
air inside the building. If the available fresh air supply is
insufficient to meet the demands of these appliances,
problems can result.
Items Needed for Heater Installation
Before installing the heater, make sure you have these
items:
• Gas piping (check local codes)
• Test gauge connection
• Sealant (resistant to LP gases) - approved
Provide for Adequate Ventilation
Any space within a home can be classified in these
categories:
thread compound
• Manual shut-off valve
*
Unusually tight construction: The air that leaks
around doors and windows may provide enough fresh
air for combustion and ventilation. However, in buildings
of unusually tight construction, you must provide
additional fresh air. Unusually tight construction is
defined as construction where:
• Sediment trap - where required
• Ground joint union
• Tee joint and pipe wrench
An installer supplied design-certified manual shut-off valve
with 1/8” NPT tap connection.
*
Walls and ceilings exposed to the outside atmosphere
have a continuous water vapor retarder with a rating of
one perm or less with openings gasketed or sealed
and;
Locating the Heater
This heater is designed to be mounted on a wall. The
heater may also be located on the floor away from a
wall. An optional floor mounting base is required and cn
be purchased from your dealer.
Caulking or sealants are applied to areas such as joints
around window and door frames, between sole plates
and floors, between wall/ceiling joints, between wall
panels, at penetrations for plumbing, electrical and gas
lines, and at other openings.
WARNING: Never install the heater:
• in a bathroom,
• in a recreational vehicle,
Unconfined space: An unconfined space whose
volume is not less than 50 cubic feet for each 1,000
Btu/Hr of the aggregate input rating of all appliances
installed in that space. Rooms communicating directly
with the space in which the appliances are installed,
through openings not furnished with doors are consid-
ered a part of the unconfined space.
• where curtains, furniture, clothing or other
flammable objects are less than 36” from the
front, top or sides of the heater,
• as a fireplace insert,
• in high traffic areas, or
• in windy or drafty areas.
WARNING: Vent-free heaters add moisture to the air.
Although this is beneficial, installing heater in rooms
without enough ventilation may cause mildew formation
from too much moisture content. See National Fuel
Code for Fresh Air for Combustion and Ventilation.
Confined space: A confined space whose volume is
less than 50 cubic feet for each 1,000 Btu/Hr of the
aggregate input rating of all appliances in that space.
WARNING: You must provide additional ventilation air
in a confined space.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Verm ont Castings VCBVTN/TP & VCPVTN/TP Room Heater
This appliance may be installed in an aftermarket*
manufactured (mobile) home, where not prohibited by
state or local codes.
Attach Mounting Screws to Wall
NOTE: Wall anchors and mounting screws are in
hardware package provided with heater.
*Aftermarket: Completion of sale, not for purpose of
resale from manufacturer.
1. Install mounting screws on wall as shown in Figure
3. Use enclosed “paper template” for proper location
of holes. Be sure template is level. It may be neces-
sary to use plastic or lead anchors for plaster walls.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases.
2. Drill holes at marked locations using 9/64” drill bit.
Insert mounting screw.
CAUTION: If you install the heater in a home garage:
• Heater must be at least 18” above floor
3. Leave screw head out from wall far enough to attach
heater.
• Locate heater where moving vehicle will not hit it.
Preparing for Installation
Template
1. Remove heater from carton.
2. Remove all protective packaging applied to heater
for shipment.
3. Check heater for any shipping damage. If heater is
damaged, promptly inform dealer/distributor.
4. Select a location for the heater that will provide
maximum exposure of the radiant surface to the
room, but will not be subjected to accidental contact.
Mounting Screws
5. Adequate clearance must be available around the
air opening. Refer to Figure 2 for clearances that
must be maintained to the side walls, floor and
horizontal surface surrounding the heater.
RH101
Fig. 3 Use paper template supplied to mark location of
mounting holes. Be sure template is level.
Ceiling
36"
(914mm)
Min.
Wall Anchor Method
When mounting heater to hollow walls (wall areas
between studs) or solid walls (concrete or masonry), it
may be necessary to use wall anchors.
Adjacent Wall
13"
(330mm)
Min.
A
1. Place paper template on wall maintaining minimum
clearance. Be sure template is level.
20"
(508mm)
Min.
Screw
Holes
2. Drill holes at marked locations using 5/16” drill bit.
For solid walls, concrete or masonry, drill holes at
least 1” deep.
3. Insert plastic anchor. Tap anchor flush to wall.
(Fig. 4)
1
A = 21
/4" (330 mm) @ 30,000 Btu/hr Model
11
13 /16" (347 mm) @ 18,000/20,000 Btu/hr Model
4. Insert screw into wall anchor leaving screw head out
far enough from wall to attach heater. (Fig. 4)
7
9
/8" (251 mm) @ 10,000 Btu/hr Model
RH110
5. Hang heater on mounting screws in holes provided
at the rear of the heater.
Fig. 2 Minimum clearances to floor, adjacent walls and
ceiling.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Verm ont Castings VCBVTN/TP & VCPVTN/TP Room Heater
Connect to Gas Supply
Before connecting the appliance, turn of all gas appli-
ances. Close the main gas valve at the gas meter or Lp
tank. Make certain there is good ventilation where the
installation will be made. Installation should comply with
all applicable building codes and ANSI Z223.1, latest
edition. Use LP gas resistant pipe compound to seal
threaded joints.
An installer supplied, design certified gas pressure
regulator must be installed to bring the gas supply
pressure down to 14” w.c.
WARNING: Never connect an unregulated gas line
to the heater.
IMPORTANT: Check gas line pressure before connect-
ing heater to gas line. Gas line pressure must not be
higher than 14” w.c. If gas line pressure is higher,
heater gas pressure regulator damage could occur.
1/16"
(1.6mm)
NOTE: The gas line connection can be made with 3/8”
black or steel pipe. Internally tinned copper tubing may
be used in certain areas. Check your local codes. Use
pipe of large enough diameter to allow proper gas
volume to heater. If pipe is too small, undue pressure
loss will occur.
RH102
Fig. 4 Wall anchor.
CAUTION: Use pipe joint sealant that is resistant to
liquefied petroleum gases.
Floor Installation
1. The heater may only be installed on a noncombus-
tible flat surface. Wall mounting screws may be used
to keep heater from side movements.
Install sediment trap in supply line as shown in Figure 6.
Locate sediment trap where it is within reach for
cleaning. Locate sediment trap where trapped matter is
not likely to freeze. A sediment trap prevents moisture
and contaminants from going into the heater controls. If
the sediment trap is not installed or is installed wrong,
the heater may not operate properly.
2. Measure heater mounting screws location “X” as
desired above floor. (Fig. 5)
3. Use enclosed “paper template” for proper distance
between holes. Be sure template is level. It may be
necessary to use plastic or lead anchors for plaster
wall.
Test for gas leaks with a mild soap and water solution.
Apply water/soap solution with brush only - do not over
apply. NEVER test with an open flame.
4. Drill holes at marked locations using 9/64” drill bit.
5. Leave screw head out from wall far enough to
attach heater.
Screw Holes
X
Floor
RH107
Fig. 5 Optional wall mounting screw for floor installation.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Verm ont Castings VCBVTN/TP & VCPVTN/TP Room Heater
Open
Pressure
Regulator
Closed
Manual
Shut-Off
Valve
Control Valve
Heater
Cabinet
3/8” NPT Nipple
Ground Joint
Union
Tee Joint
Reducer
Bushing to
1/8” NPT
Manual
Shutt-Off
Valve
Manual
Shut-Off
Valve
1/8” NPT
Plug Tab
From Gas
Meter
Natural Gas
(4” w.c. to
Tee Joint
10.5” w.c. Pressure)
LP Gases
Pipe Nipple
RH104
(11.5” w.c. to
Cap
14.0” w.c. Pressure)
RH103
Fig. 7 Manual shut-off valve location.
Fig. 6 Gas line connection.
Leak Testing Heater Gas Connections
Pressure Test Gas Supply Piping System
1. Open manual shut-off valve.
2. Open main gas valve located near gas meter.
The appliance and its individual shut-off valve must be
disconnected from the gas supply piping system during
any pressure testing of the system at test pressures in
excess of 1/2 psi.
3. Make sure control knob of heater is in the OFF
position.
4. Check all joints from manual gas valve up to control
valve and including the manifold assembly. Apply the
soap solution around the connections, valve and
tubing. Soap bubbles will appear where a leak is
present.
The appliance must be isolated from the gas supply
piping system by closing the individual manual shut-off
valve (Fig. 7) during any pressure testing of the gas
supply system at test pressures equal to or less than
1/2 psi.
5. If a leak is present, immediately turn off gas supply,
tighten any leaky fittings, turn gas on and recheck.
6. To check burner and safety valve, the burner must
be lit (see Operating Instructions). Check the rest of
the connections for leaks.
7. Turn off the heater.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Verm ont Castings VCBVTN/TP & VCPVTN/TP Room Heater
Op e ra t in g In s t ru ct io n s
NOTE: If pilot does not stay lit, refer to troubleshooting
FOR YOUR SAFETY - READ THIS SECTION
BEFORE LIGHTING
section and contact a qualified service person, or gas
supplier for repairs. Until repairs are made, light pilot
with match.
WARNING: IF YOU DO NOT FOLLOW THESE
INSTRUCTIONS EXACTLY, A FIRE OR EXPLO-
SION MAY RESULT CAUSING PROPERTY DAM-
AGE, PERSONAL INJURY OR LOSS OF LIFE.
6. Keep control knob pressed in for 30 seconds after
lighting pilot. After 30 seconds, release control knob.
7. If pilot goes out, repeat steps 3 through 6. This
heater has a safety interlock system. Wait one (1)
minute before relighting pilot.
A. BEFORE LIGHTING smell all around the appliance
area for gas. Be sure to smell next to floor because
some gas is heavier than air and will settle on the
floor.
8. When the pilot is lit, turn gas control knob to ON.
Turn thermostat control knob counterclockwise
to desired heating level. The main burner
should light. Set control knob to heat level between
7 and 1.
IF YOU SMELL GAS:
1. Do not try to light any appliance.
PILOT
2. Do not touch electrical switches; do not use any
phone in your building.
7
5
3. Immediately call your gas supplier from a
neighbor’s phone. Follow your gas supplier’s
instructions.
4
3
4. If you cannot reach your gas supplier, call the fire
department.
RH108
Fig. 8 Control knob.
B. Use only your hand to push in or turn the gas valve
control knob. Never use tools. If the knob will not
push in or turn by hand, do not try to repair it, call a
qualified service technician. Force or attempted
repair may result in a fire or explosion.
To Turn Off Gas To Heater
Turning Heater Off
Turn control knob clockwise to the OFF position.
Turning Burner Only Off (Pilot stays lit)
Turn control knob clockwise to the PILOT position.
C. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of
this control system and any gas control which has
been under water.
CAUTION: Do not try to adjust heating levels by
using the manual shut-off valve.
NOTE: The thermostat has a sensing bulb and a
temperature control knob. The thermostat used on this
heater senses the room temperature and turns the
burner on and off. At times the room may exceed the
set temperature. If so, the burner will shut off. The
burner will cycle back on when room temperature drops
below the set temperature.
Lighting Instructions
1. Read the safety information.
2. Make sure manual shut-off valve is fully open.
3. Push in gas control knob slightly and turn clockwise
to the OFF position.
4. WAIT 5 MINUTES TO CLEAR OUT ANY GAS. If
you then smell gas, STOP! Follow A in the safety
information. If you do not smell gas, go to next step.
5. Push in gas control knob slightly and turn counter-
clockwise
to ‘IGN PILOT.” The pilot can be
seen through the glass panel. If needed, keep
pressing and turning the control knob counterclock-
wise
until the pilot lights.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Verm ont Castings VCBVTN/TP & VCPVTN/TP Room Heater
VCBV Heater
Manual Lighting Instructions
1. Remove lower front panel.
Yellow Tipping
2. Follow steps 1 through 4 as stated under Lighting
Instructions.
3. Press and turn control knob counterclockwise
to the PILOT position.
Correct
Incorrect
RH106
4. With control knob pressed in, strike match, hold
match to pilot until pilot lights.
Fig. 10 Correct burner flame pattern for the VCBV blue flame
burner.
5. Keep control knob pressed in for 30 seconds after
lighting pilot. After 30 seconds, release control knob.
6. Replace lower front panel.
VCPV Heater
Pilot and Burner Inspection
Each time you light your heater check that the pilot
flame and burner flame patterns are as shown in
Figures 9, 10 and 11. If flame patterns are incorrect,
turn the heater off. Contact your dealer or a qualified
gas technician for assistance. Do not operate the
heater until the pilot flame is correct.
Correct
WARNING: If yellow tipping occurs, your heater could
produce increased levels of carbon monoxide. If burner
flame pattern shows yellow tipping, follow instructions
in the Troubleshooting section on page 10. NOTE: do
not mistake orange flames with yellow tipping. Dirt or
other particles may enter the heater and cause tran-
sient patches of orange flame.
Incorrect
RH109
Ignitor Electrode
Thermocouple
Fig. 11 Correct burner flame pattern for the VCPV plaque
heater.
Incorrect
Correct
P103
Fig. 9 Proper pilot flame.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Verm ont Castings VCBVTN/TP & VCPVTN/TP Room Heater
Tro u b le s h o o t in g
Problem
Possible Cause
What To Do
When control knob is pressed
in and turned counterclockwise
to ignition, there is no spark at
ODS pilot.
1. Ignitor electrode positioned wrong.
2. Ignitor electrode broken.
3. Ignitor cable pinched or broken.
1. Replace ignitor electrode.
2. Replace electrode.
3. Free ignitor cable, if damaged
replace.
4. Ignitor cable not connected to ignitor
electrode.
4. Connect cable to electrode.
When control knob is pressed
in and turned counterclockwise
to ignition/pilot position, there
is spark but no ignition.
1. Gas supply turned off.
2. Control knob not in pilot position.
3. Control knob not pressed in while in
pilot position.
1. Turn gas supply on.
2. Turn control knob to pilot position.
3. Press in control while in pilot
position.
4. ODS pilot is clogged.
5. Air in gas lines.
4. Call a qualified service technician.
5. Purge gas lines and repeat ignition
operation.
ODS pilot lights but flame goes
out when control knob is
released.
1. Control knob not pressed long
enough.
1. After ODS pilot lights, keep control
knob pressed in approximately 30
seconds.
2. Safety interlock is triggered.
2. Wait one minute, repeat ignition
operation.
3. Pilot flame not touching the thermo-
couple. Problem could be result of
one or both of the following:
3. Contact your gas company, gas
supplier or qualified service
technician.
• Partially clogged ODS pilot orifice.
• Low gas pressure.
4. Replace thermocouple.
5. Hand tight until snug then tighten
1/4 turn with a wrench.
4. Thermocouple damaged.
5. Thermocouple connection loose at
gas control valve.
6. Replace gas control.
1. Clean burner orifice.
2. Contact gas supplier.
1. Clean main burner ports.
6. Gas control valve damaged.
1. Burner orifice clogged.
2. Gas supply pressure is very low.
1. Main burner carry over ports
clogged.
Burner does not light after ODS
pilot is lit.
Delayed ignition.
2. Contact gas supplier.
1. Clean or replace burner orifice.
2. Replace burner.
2. Gas supply pressure is very low.
1. Burner orifice is clogged or clogged.
2. Burner damaged.
Burner backfiring during
operation.
3. Replace gas regulator.
1. Check air passageways and
burner for dirt and debris. (Refer to
Maintenance section.)
3. Gas regulator defective.
1. Not enough air.
Yellow flames during burner
operation. (VCBV)
1. Replace burner.
Burner plaque(s) does not
glow. (VCPV)
1. Plaque(s) is damaged.
2. Inlet gas pressure is too low.
3. Control knob set between locked
positions.
2. Contact local gas supplier.
3. Turn control knob until it locks at
desired setting.
1. Will stop after a few hours of
operation.
Slight smoke and odor during
initial operation.
1. Residues from manufacturing
processes.
1. Check minimum installation
clearances and air passageways
for debris.
Heater produces a whistling
noise when burner is lit.
1. Air passageways blocked.
2. Operate burner until the air is
completely purged.
2. Air in gas line.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Verm ont Castings VCBVTN/TP & VCPVTN/TP Room Heater
Troubleshooting, continued
Problem
Possible Cause
Solution
Heater produces a clicking
noise just after burner is lit or
turned off.
Gas odor even when control
knob is in OFF position.
1. Metal expanding and contracting.
1. This is common with heaters. If
noise is excessive, contact a
qualified service technician.
1. Locate and correct leaks immedi-
ately.
1. Gas leaks. Refer to front page
Warnings.
2. Gas control defective.
1. Foreign matter in gas or on burner
ports.
2. Replace gas control.
1. Check gas passage way and
burner.
Gas odor during combustion.
2. Heater burning vapors form paint,
impurities in air.
2. Ventilate room, stop storing and
using odor causing products near
heater.
3. Gas leaks, refer to front page
Warnings.
3. Locate and correct leaks immedi-
ately.
Heater shuts off on ODS
1. Not enough fresh air is available.
2. Low gas pressure.
3. ODS pilot partially clogged.
1. Open window.
2. Contact gas supplier.
3. Clean the pilot.
Ma in t e n a n ce
Dust, lint, cobwebs or debris may affect heater perfor-
mance. The heater draws air into it during normal
operation and in the process dust, lint or debris may be
drawn in also. It is important to keep the burner, gas
control and combustion and circulating air passage-
ways clean. Inspect or have these areas inspected
annually at the beginning of the heating season by a
qualified service person. Depending on the surround-
ings, the room heater may require frequent cleaning
due to excessive lint or debris.
Burner and ODS Pilot Cleaning
Clean the exterior with soft bristle brush, vacuum
cleaner pressurized air. Never use a wooden toothpick
as it may break off and clog the ODS pilot or main
burner port.
Use a flashlight to inspect the main burner inlet to
ensure it is not blocked. If obstruction can be seen, use
a metal wire coat hanger that has been straightened
out.
Before cleaning ensure the gas supply is off and the
gas control knob is in the OFF position. Make sure the
heater is cool.
Use a vacuum cleaner to clean the primary air
openings to the main burner(s).
WARNING: Failure to keep the primary air openings
to the burner(s) clean may result in sooting and
property damage.
WARNING: Danger of bodily injury. If fan assembly
accessory is used, turn off power supply at discon-
nect switch or service panel before removing any
access panels from heater.
In order to clean ODS pilot orifice, use pressurized air
to blow dust out. Sometimes blowing air backwards
through the pilot will get rid of the accumulated dirt. If
that does not work, blow out any dust through primary
air openings of pilot assemblies (Daemyeong has two
openings; one beneath the bimetal strip and the second
one opposite from bimetal strip. Use the one wide
open, do not try to lift the bimetal strip.)
Cleaning Air Passageways
and Unit Casings
Use a vacuum cleaner or pressurized air to clean the
combustion and circulating air passageways and
dampened cloth to clean the cabinet/casing.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Verm ont Castings VCBVTN/TP & VCPVTN/TP Room Heater
10
12
5
13a,b
15
18
14
20
19
21a,b
9a
9b
16
11
25a,b
6
17
22a,b
8
7
6
2
3
23
24
4
1
3771
The Vermont Castings Majestic Products Company reserves the right to make changes in design, materials, specifications, prices and discontinue
colors and products at any time, without notice.
VCBVTN/ TP Unvented Room Heater
Item / Model Number
VCBV10TN/TP
VCBV20TN/TP
VCBV30TN/TP
1.
2.
3.
4.
5.
6.
7.
8.
9a.
9b.
10.
11.
12.
13a.
13b.
14.
15.
16.
17.
18.
19.
Guard Assembly
RBW33XX0
RBC02XC0
RBP63PC0
RBP71PX0
RBP69PA0
RBI06XX0
--
RBW13XX0
RBP06XA0
RBP06XB0
RBW31PA0
RBI05XX0
RBP59XX0
RBAXE0
RBW30XX0
RBC02XB0
RBP63PB0
RBP70PX0
RBP66PA0
RBI06XX0
RBP61XB0
RBW09XX0
RBP06XA0
RBP06XB0
RBW27PA0
RBI05XX0
RBP59XX0
RBA01XC0
RBA01XD0
RBM03XX0
RBM02XX0
RBT19XX0
RBT18XX0
RBT17XX0
RBM06XX0
RBW26XX0
RBC02XA0
RPB63XPA0
RBW23XX0
RBW22XA0
RBI06XX0
RBP61XA0
RBW08XX0
RBP06XAO
RBP06XB0
RBW20PA0
RBI05XX0
Glass Panel
Holder Glass
Reflector
Front Panel
Leg - Front
Cover Heat - Upper
Burner Assembly
Burner Support - Left
Burner Support - Right
Frame Body Assembly
Leg - Rear
Bracket - Valve
RBP59XX0
RBA01XA0
RBA01XB0
RBM03XX0
RBM02XX0
RBT13XX0
RBT12XX0
RBT11XX0
RBM06XX0
Combination Gas Control - Natural
Combination Gas Control - LP
Connector - “C”
RBAXF0
RBM03XX0
RBM02XX0
RBT25XX0
RBT24XX0
RBT23XX0
RBM06XX0
Connector - “B”
Tubing ODS Assembly
Tubing Outlet Assembly
Tubing Inlet Assembly
Nozzle Holder
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Verm ont Castings VCBVTN/TP & VCPVTN/TP Room Heater
VCBVTN/ TP, continued
Item / Model Number
VCBV10TN/TP
RBM08XX0
RBM07XEO
RBM07XF0
DS98JN02
DS98JL02
RBP100
VCBV20TN/TP
RBM08XX0
RBM07XA0
RBM07XB0
DS98JN02
DS98JL02
RBP101
VCBV30TN/TP
RBM08XX0
RBM07XC0
RBM07XD0
DS98JN02
DS98JL02
RBP105
20.
21a.
21b.
22a.
22b.
23.
Fix Nut - Nozzle Holder
Main Nozzle - Natural
Main Nozzle - LP
ODS Pilot Assembly (Daemyeong Korea) - Natural
ODS Pilot Assembly (Daemyeong Korea) - LP
Shield
24.
Rear Radiant Heat Shield
--
10003986
10003984
25a.
25b.
Pressure Regulator (Daemyeong Korea) - Natural
Pressure Regulator (Daemyeong Korea) - LP
DR40M2PN
DR40M2PL
DR40M2KN
DR40M2KL
DR40M3KN
DR40M3KL
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Verm ont Castings VCBVTN/TP & VCPVTN/TP Room Heater
11
9
17
20a,b
12
14
17
13
19
6
23a,b
15
16
5
18a,b
8
10
7
5
4
3
21
2
22
1
3770
The Vermont Castings Majestic Products Company reserves the right to make changes in design, materials, specifications, prices and discontinue
colors and products at any time, without notice.
VCPVTN/ TP Unvented Room Heater
Item / Model Number
1. Cover Heat - Lower
2. Guard Assembly
3. Reflector
4. Cover Heat - Upper
5. Leg - Front
6. Front Panel
7. Burner Body Assembly
8. Ceramic - Plate
9. Frame Body Assembly
10. Leg - Rear
11. Bracket - Valve
12. Combination Gas Control
13. Connector - “C”
14. Connector - “B”
15. Tubing ODS Assembly
16. Tubing Outlet Assembly
17. Tubing Inlet Assembly
18a. ODS Pilot Assembly - Natural
18b. ODS Pilot Assembly - LP
19. Manifold Assembly
VCPV10TN/TP
RCP10XC0
RBW33XX0
RCP34PX0
--
VCPV18TN/TP
RCP10XB0
RBW30XX0
RCP33PX0
RBP61XB0
RBI06XX0
RBP66PA0
RCW12XX0
RCC01XA0
RBW27PB0
RBI05XX0
RBP59XX0
RBA01XG0
RBM03XX0
RMB02XX0
RCT57
VCPV30TN/TP
RCP10XA0
RBW26XX0
RCW10XX0
RBP61XA0
RBI06XX0
RBP57PA0
RCW11XX0
RCC01XA0
RBW20PA0
RBI05XX0
RBP59XX0
RBA01XG0
RBM03XX0
RMB02XX0
RCT48
RBI06XX0
RBP69PA0
RCW13XX0
RCC03XX0
RBW32PA0
RBI05XX0
RBP59XX0
RBA01XG0
RBM03XX0
RMB02XX0
RCT63XX0
RCT62XX0
RCT61XX0
DS98JN01
DS98JL01
--
RCT56XX0
RCT55XX0
DS98JN01
DS98JL01
RCT02PB0
RCT47XX0
RCT46XX0
DS98JN01
DS98JL01
RCT02PA0
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Verm ont Castings VCBVTN/TP & VCPVTN/TP Room Heater
VCPVTN/TP, continued
Item / Model Number
VCPV10TN/TP
RCM02XD0
RCM02XE0
--
VCPV18TN/TP
RCM02XC0
RCM02XB0
10003986
VCPV30TN/TP
RCM02XA0
RCM02XB0
10003985
20a. Main Nozzle - Natural
20b. Main Nozzle - LP
21. Rear Radiant Heat Shield
22. Shield
RBP84
RBP101
RBP104
23a. Pressure Regulator (Daemyeong Korea) - Natural
23b. Pressure Regulator (Daemyeong Korea) - LP
DR40M2PN
DR40M2PL
DR40M3PN
DR40M3PL
DR40M5PN
DR40M5PL
Acce s s o rie s
The following accessories are available from your local Vermont Castings dealer. Each accessory comes with a
separate installation instruction. Be sure to read each instruction thoroughly before installing.
Description
Manual Fan Kit
Model Number
FMA-F
Thermostat Fan Kit
FMA-FT
Contact Vermont Castings, Majestic Products with
questions concerning prices and policies covering
replacement parts. Parts may be ordered through you
Vermont Castings distributor or dealer.
Model and serial numbers are listed on the rating
plate (located on right side of heater). Record your
model and serial numbers here for future reference.
You will need the following information when ordering
replacemet parts:
Model # ___________________________________
Serial # ___________________________________
• the appliance model number,
• the serial number, and
• a description of the part.
Should you need additional information beyond
what your dealer can furnish, contact:
Vermont Castings, Majestic Products
410 Admiral Blvd.
Mississauga, Ontario
Canada L5T 2N6
Telephone: 905-670-7777
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Service and Limited Warranty
TO THE FULL EXTENT ALLOWED BY THE LAW OF
The Vermont Castings Majestic Products Company
warrants this product to be free form defects in materi-
als and components for two (2) years from the date of
first purchase, provided that the product has been
properly installed, operated and maintained in accor-
dance with all applicable instructions. To make a claim
under this warranty the Bill of Sale or cancelled check
must be presented.
THE JURISDICTION THAT GOVERNS THE SALE OF
THE PRODUCT; THIS EXPRESS WARRANTY EX-
CLUDES ANY AND ALL OTHER EXPRESSED WAR-
RANTIES AND LIMITS THE DURATION OF ANY AND
ALL IMPLIED WARRANTIES, INCLUDING WARRAN-
TIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE TO TWO (2) YEARS FROM
THE DATE OF FIRST PURCHASE; AND THE VER-
MONT CASTINGS MAJESTIC PRODUCTS COMPANY
SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES
WHATSOEVER INCLUDING INDIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES.
This warranty is extended only to the original retail
purchaser. This warranty covers the cost of part(s)
required to restore this heater to proper operating
condition and an allowance for labor when provided by
a Vermont Castings authorized dealer/distributor.
Warranty part(s) MUST be obtained through authorized
dealers of this product and/or Vermont Castings Majes-
tic Products who will provide original factory replace-
ment parts. Failure to use original factory replacement
parts voids this warranty. The heater MUST be installed
by a qualified installer in accordance with all local
codes and instructions furnished with the unit.
Some states do not allow a limitation on how long an
implied warranty lasts or an exclusion or limitation of
incidental or consequential damages, so the above
limitation on implied warranties, or exclusion or limita-
tion on damages may not apply to you.
This warranty gives you specific legal rights, and you
may also have other rights that vary from state to state.
This warranty does not apply to parts that are not in
original condition because of normal wear and tear, or
parts that fail or become damaged as a result of
misuse, accidents, lack of proper maintenance or
defects caused by improper installation. Travel, diag-
nostic cost, labor, transportation and any and all such
other costs related to repairing defective heater will be
the responsibility of the owner.
Always specify model and serial number when commu-
nicating with the factory.
Ver m on t Ca st in gs, Ma jest ic P r od u ct s
410 Admiral Blvd. • Mississauga, Ontario • Canada, L5T 2N6 • 905-670-7777
© Vermont Castings, Majestic Products
Download from Www.Somanuals.com. All Manuals Search And Download.
|