PLV16070
Portable Digital TV
7” widescreen LCD
Instruction Manual
Need More Help?
DO NOT RETURN THIS PRODUCT TO THE STORE
Please visit online help at
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety PrecautionS
The lightning flash with an arrowhead symbol, within the equilateral triangle, is intended to
alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to cause an electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in this owner’s manual.
WarninG: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICINGTO QUALIFIED
SERVICE PERSONNEL.
WarninG: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSETHISAPPLIANCE
TO RAIN OR MOISTURE. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR
NEAR THIS UNIT.
WarninG: SHOUld ANy TROUBlE OCCUR, dISCONNECT THE AC POwER
ADAPTER AND REFER SERVICING TO A QUALIFIED TECHNICAN.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
• Consult the dealer or an experienced radio/TV technician for help.
Shielded cables must be used with this unit to ensure compliance with the Class B FCC limit.
WarninG:
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
iMPortant Safety inStructionS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. do not use this apparatus near water.
6. Clean only with a dry cloth.
7. do not block any of the ventilation openings.
Install in accordance with the manufacturer’s
instructions.
12. Use only with a cart,
stand, tripod, bracket,
or table specified by the
manufacturer,orsoldwith
theapparatus.whenacart
is used, use caution when
movingthecart/apparatus
combination to avoid
injury from tip-over.
Portable cart
Warning
8. do not install near any heat sources such 13. Unplugthisapparatusduringlightningstorms
as radiators, heat registers, stoves, or other or when unused for long periods of time.
apparatus (including amplifiers) that produce 14. Refer all servicing to qualified service
heat.
personnel. Servicing is required when the
apparatushasbeendamagedinanyway, such
as the power-supply cord or plug is damaged,
liquidhasspilledorobjectshavefallenintothe
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally,
or has been dropped.
9. do not defeat the safety purpose of the
polarizedorgrounding-typeplug.Apolarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong is provided for your safety.
when the provided plug does not fit into your
AC power outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles,andthepointwheretheyexitfrom
the apparatus.
11. Only use attachments/accessories specified
by the manufacturer.
content
Safety Precautions ......................................... 1 tV Setting ............................................. 11-14
important Safety instructions ........................ 2
content ......................................................... 2
accessories ................................................... 3
remote control ............................................. 3
Quick Start Guide ......................................... 4
Picture Menu .......................................... 11
Audio Menu ............................................ 11
Time Menu .............................................. 12
Setup Menu ....................................... 12-13
Channel Menu ................................... 13-14
control reference Guide .......................... 5-6 Maintenance ............................................... 14
connections .............................................. 7-8 troubleshooting Guide ................................ 15
Connecting a TV Antenna / Cable / Satellite . 7
Connecting a digital antenna .....................8
Using Headphones / Earphones ................. 8
using the flip-out Stand................................. 8
Power Supply .......................................... 9-10
Using the AC Adapter ................................ 9
Using the Car Power Adapter .................... 9
Using the Built-in Battery ........................ 10
Turning on the Unit ................................. 10
- 2 -
Download from Www.Somanuals.com. All Manuals Search And Download.
acceSSorieS
Remote control with batteries ................................................................................................... x 1
Car power adapter .......................................................................................................................... x 1
AC adapter ............................................................................................................................... x 1
Auxiliary antenna ........................................................................................................................... x 1
reMote control
• Point the remote control at the REMOTE SENSOR located on the unit.
• When there is a strong ambient light source, the performance of the infrared REMOTE SENSOR
may be degraded, causing unreliable operation.
• The recommended effective distance for remote operation is about 16 feet (5 meters).
To Install Batteries
2. Insert two AAA batteries.
1. Open the battery door.
Battery Replacement
when the batteries become weak, the operating distance of the remote control is greatly reduced
and you will need to replace them.
caution: danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type.
notes:
• If the remote control is not going to be used for a long time, remove the batteries to avoid corrosion
damage caused by battery leakage.
• Do not mix old and new batteries. Do not mixALKALINE, standard (CARBON-ZINC) or rechargeable
(NICKEl-CAdMIUM) batteries.
• Always remove batteries as soon as they become weak.
• Weak batteries can leak and severely damage the remote control.
WarninG: do not dispose of batteries in a fire. Batteries may explode or leak.
Many universal remote controls have a “learning” feature. we recommend you use that feature to
program the remote control.
For any questions or problems related to programming a universal remote control, you must contact
the customer service department of the universal remote control manufacturer for assistance, or
refer to the instructions included with the universal remote control. we cannot offer assistance in
programming universal remote controls.
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
QuicK Start GuiDe
turninG on the unit for the firSt tiMe
The first time you turn on the unit, the unit will enter the setup mode.you can easily follow the prompt
message on the screen to complete basic TV settings.
Make sure the TV antenna has been connected properly to the antenna rf in terminal
on the side of the TV.
1. Press the
/
button to select your preferred
Setup Wizard
On-screen menu language. Use the
/
button to highlight “Go to next step:“ and
press the enter button to enter next setup
screen.
Please select your prefer language :
Menu Language
Go to next step :
English
MENU
ENTER
2. Use the
different items, then press the
to select the desired options. Use the
/
button to switch between
/
button
Setup Wizard
/
Select the time zone & Daylight saving time:
button to move the highlight bar on “Go to
next step:“ and press the enter button to
enter next setup screen.
Time Zone
DST
Pacific
Off
Time Format
Go to next step :
24-hour
MENU
ENTER
3. Use the
press the
/
button to select Air/Cable, then
button to select Air or Cable.
Setup Wizard
/
Highlight “Go to next step:“ and press the
enter button to start scanning channels.
Select the antenna type then auto scan:
Air / Cable
Air
Cable System
AUTO
Go to next step :
MENU
ENTER
4. After scanning finishes, the system will return to the first TV channel scanned.
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
control reference GuiDe
Remote Control
1)
Mute Button
SIGNAL
Press to turn off the sound.
2) Menu Button
Press to display the on-screen menu or switch
back to the previous menu screen.
3) curSor (
,
,
,
) Buttons
Use to highlight selections on a menu screen
and adjust certain settings.
enter Button
Confirm selection on a menu screen.
4) DiSPlay Button
Press to display information about the current
TV channel.
5) Vol + / Vol - Buttons
Press to adjust the volume level.
6) laSt ch
Press to switch to previously selected TV
channel.
7) SiGnal Button
Press to display TV signal quality.
8) cc Button
PresstoturnonorchangesettingsfortheClosed
Caption feature.
9) lcD MoDe Button
Press to select the desired screen aspect ratio
- 4:3, Wide (16:9), or Auto - for the particular
program you’re watching.
10) ch / ch Buttons
Press to select the channel upward or
downward.
11) nuMeric Buttons
Presstoenternumbersorgodirectlytoaspecific
channel.
12) • [dot] Button
Press to enter digital TV sub-channels with the
numeric buttons (i.e. 11.3 or 12.7).
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
control reference GuiDe
Unit
1) Screen
6) Direct-connect antenna connecting to the
antenna rf in terminal
2) enter Button
7) heaDPhone Jack
Confirm selection on a menu screen.
8) on / / charge Switch
Menu Button
on position:TurnsTV ON, green indicator
will be ON.
Presstodisplaytheon-screenmenuorswitch
back to the previous menu screen.
position: Puts TV in standby mode.
ch + / ch - Buttons
charge position: Recharges the battery, red
indicator will be ON.
Press to select the channel upward or
downward.
Vol + / Vol - Buttons
9) Dc in 9V - 12V Jack
Press to adjust the volume level.
Connect the supplied AC adapter.
3) Speaker
4) remote Sensor
Receives infrared signals from the remote
control.
5) flip-out Stand
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
connectionS
Connecting a TV Antenna / Cable / Satellite
To view television channels correctly, a signal must be received from one of the following sources:
-
-
-
An indoor or outdoor aerial antenna
A cable system
A satellite system
removing Direct-connect antenna Before
connecting a different antenna or a coaxial
cable, you need to remove the direct-connect
antenna first.
using Direct-connect antenna
To optimize TV reception, try adjusting the
orientation and position of the direct-connect
antenna.
Hold the direct-connect antenna
and rotate the nut as shown below
to remove.
using a Different antenna
Cable TV (without a CATV converter)
To TV ANTENNA terminal
(cable not included)
Combination VHF/UHF antenna
(ATSC / NTSC signal)
Separate VHF/UHF antenna
(ATSC / NTSC signal)
Auxiliary antenna
(included with this product)
how to connect the auxiliary antenna
1. Hold the connector of auxiliary antenna and rotate
the nut to the ANTENNA RF IN terminal on the
side of the TV.
2. Remove the cap on the base of Auxiliary Antenna.
3. Hold the antenna rod ofAuxiliaryAntenna and rotate
the nut to the base until it is fastened.
4. Extend the antenna rod and adjust position for
optimal reception.
3
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
connection
note
optimal indoor reception of over-the-air tV broadcasts is typically achieved using an external
fixed antenna. you may find that indoor reception is adequate using the direct-connect antenna.
however, for your convenience, we’ve also included an additional antenna with a long cable to
give you extra flexibility in antenna placement. in general, you’ll often find that placement of the
antenna near windows, or at higher elevations, should improve reception. if you seek to further
improve reception, we recommend you purchase the appropriate antenna that is suitable for your
particular environment.
Connecting a Digital Antenna
The tuner in this TV receives ATSC TV signals from an antenna.
This digital TV can receive standard (SDTV) and high definition (HDTV) over the air broadcasts.
Using Headphones / Earphones
• Turn down the volume before connecting headphones
to the unit, then adjust the volume to your desired
level.
• When headphones are connected, no sound will come
from the front speaker.
caution:
Avoid listening to sound at high levels for prolonged
periods of time. This may be harmful to you and may
cause hearing loss.
Headphones / Earphones
(3.5mm diameter plug)
uSinG the fliP-out StanD
The stand is located on the rear panel of the unit. Pull
the stand out and rotate it to the maximum angle (shown
as right).
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
PoWer SuPPly
Using the AC Adapter
The supplied 9V adapter operates on AC 120V ~ 60Hz.
AC Power Adapter
cautions:
• The AC power adapter included with this unit
is for its use only. do not use it with other
equipment.
• To prevent electrical shock, match wide blade
of plug to wide slot of wall outlet, then fully
insert.
• When the unit is not going to be used for long
time, disconnect the AC power adapter from the
AC power outlet.
To AC
outlet
To DC IN
9-12V jack
• When the AC power adapter is plugged in, the
apparatus is not completely disconnected from
the main power supply, even when the power is
turned off.
• The AC power adapter shall not be exposed to
dripping or splashing and that no objects filled
with liquids, such as vases, shall be placed on
apparatus.
Warning:
The AC power adapter is used as disconnect device and it should remain readily operable during
intended used. In order to disconnect the apparatus from the mains completely, the AC power
adapter should be disconnected from the mains socket outlet completely.
Using the Car Power Adapter
The 12V car power adapter allows the unit to be used with vehicles that have a 12V, negative ground
electrical system.
note: It is not possible to satisfactorily receive ATSC TV signals while in motion - the car power
adaptor is intended for uses such as “tail-gating”.
WarninG:
To DC IN 9-12V jack
Car Power Adapter
disconnect the car power
adapter when not in use. Not
for use in 24V vehicles.
To the cigarette 1
lighter socket
fuse replacement instructions
Press and hold
caution:
For continued protection against risk of fire,
replace only with same type and rating of fuse.
Fuse
Press and hold
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
PoWer SuPPly
Cautions:
• Use the provided 12V car power adapter only. Use with other car power adapters could damage
the unit.
• The 12V car power adapter included with this unit are for its use only. Do not use them with other
equipment.
• In the interest of traffic safety, do not operate this unit while driving a vehicle.
• Make sure the unit is securely fastened to prevent it from falling or flying through the air in the
event of an accident.
• If the inside of the cigarette lighter socket is dirty with ashes or dust, the plug section may become
hot due to poor contact. Be sure to clean the cigarette lighter socket before use.
• After use, disconnect the 12V car power adapter from both the unit and cigarette lighter socket.
Using the Built-in Battery
The unit has a built-in, non-replaceable, rechargeable battery. Charge the built-in battery before using
it for the first time. Before charging, make sure the on /
/ charge switch is slid to Charge Mode
positionandtheACpoweradapterispluggedin.Thenormalchargingtimeshouldbecompletedwithin
4-5 hours. The red charging light will go out when the built-in battery becomes fully charged.
warnings:
• The built-in battery can only be recharged when the unit is in CHARGE mode while using the AC
power adapter.
• The built-in battery cannot be recharged when the unit is in ON mode.
• Do NOT recharge the built-in battery in a vehicle using the car power adapter.
• Batteries should not be exposed to excessive heat such as sunshine, fire or the like.
Notes:
• When the built-in battery power is low, "
Battery Low" will display on the screen and the unit
will stop playing.
• Recharge the built-in battery when you are ready to use it again.
• While using the built-in battery, the environmental temperature should be 41°F (5°C) to 95°F
(35°C).
• To get the longest service life of the built-in battery, charge at indoor-temperature.
• The built-in battery in this device may present a risk of fire or chemical burn if mistreated. Do not
disassemble, heat above 212°F (100°C), or incinerate.
• The unit should not be exposed to excessive heat such as sunshine, fire or the like.
• When discarding the unit, environmental problems must be considered and local rules or laws
governing the disposal of such products must be strictly followed.
Turning on the Unit
The supplied AC adapter operates on AC 120V.
•
Slide the on /
/ charge Switch to on mode on
the side of unit to turn on the unit - the green power
indicator will light up.
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
tV SettinG
Picture Menu
1. Press the Menu button.
2. Use the
or
button to select the options
Picture
(Picture Mode, contrast, Brightness, Sharpness,
color, color temp or lcD Mode). Adjust them
using the or button (Screen will change to
your desired setting).
Picture Mode
Contrast
Brightness
Sharpness
Color
Standard
50
50
50
50
3. Repeat step 2 to adjust other options.
4. To exit the MAIN MENU and return to the normal
Color Temp
LCD Mode
Normal
Wide
screen, press the Menu button repeatedly.
MENU
ENTER
Picture Mode
:
:
Select from preset screen display settings to match the type of show you are watching
(Standard, dynamic, Soft and Personal). Select Personal mode to recall your custom
settings on contrast, brightness, sharpness and color.
Adjust the contrast of the picture. The black portions of the picture become richer
in darkness and the white become brighter.
contrast
Brightness
Sharpness
color
:
:
:
:
Adjust the brightness of the picture. Brighten or darken the whole picture.
Adjust the sharpness level to improve detail in the picture.
Adjust the color of the picture.
color temp
Adjust the color temperature of the picture. Choose from Normal (balanced),warm
(red white) or Cool (blue white) modes.
lcD Mode
:
Set the lCd display ratio. Choose from Auto, 4:3 or wide modes.
Audio Menu
1. Press the Menu button.
2. Use the or button to select audio, then press
the button to enter the Audio settings.
3. Adjust it using the or button.
4. To exit the MAIN MENU and return to the normal
Audio
Audio Channel
Primary Audio
screen, press the Menu button repeatedly.
MENU
ENTER
NOTE:
SomeTV stations may broadcast more than one audio channel for a particularTV channel. For example,
it may broadcast in English language on its primary audio channel, while broadcasting in Spanish, or
broadcasting Descriptive Audio (for the Visually-Impaired) on a secondary audio channel.
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
tV SettinG
TIME Menu
1. Press the Menu button.
2. Use the or button to select time, then press
Time
the button to enter the Time settings.
Time Zone
DST
Time Format
Clock
Pacific
Off
24-hour
3. Use the or button to select the options (time
Zone, DSt or time format). Adjust them using
the or button.
-- -- / -- /-- --:--
4. Repeat step 3 to adjust other options.
5. To exit the MAIN MENU and return to the normal
screen, press the Menu button repeatedly.
MENU
ENTER
time Zone
: Select the time zone from Pacific / Alaska / Hawaii / Atlantic / Eastern
/ Central / Mountain.
DSt (Daylight Saving time) : Select On to activate daylight saving time.
time format
: Select the time format 12-hour / 24-hour.
clock
: display the current time.
SETUP Menu
1. Press the Menu button.
2. Use the or button to select Setup, then press
the button to enter the Setup settings.
3. Use the or button to select the options (Menu
language,transparency, Menutime-out, closed
caption or restore Default). Adjust them using
the or button (Screen will change to your
desired setting); or press the button to go into
the detailed settings.
Setup
Menu Language
Transparency
English
25%
15 Sec.
Menu Time-Out
Closed Caption
Restore Default
4. Press the Menu button to return to the previous
menu.
MENU
ENTER
5. Repeat steps 3 and 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal
screen, press the Menu button repeatedly.
Menu language: Select On-screen menu language from English / French / Spanish.
transparency : Set the transparency of the On-Screen Menus.
Menu time-out: Once the interval period is set, the On-Screen Menu will disappear from the screen
when it reaches the preset interval time. The available values are: 5 Sec., 15 Sec.,
30 Sec., 45 Sec. or 60 Sec.
restore Default : If you reset the TV to the factory settings, all your present settings on PICTURE and
AUdIO will be erased and replaced by the factory’s default settings.
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
tV SettinG
Closed Caption
cc Mode
: Select closed caption On,
Off or CC on Mute.
analog closed caption : Select the analog closed
caption or turn it off.
Digital closed caption : Select between different
digital closed captions or
Setup
CC Mode
CC Off
CC1
Service1
Analog Closed Caption
Digital Closed Caption
Option
turn it off.
option
: Select as default to use
the default digital caption
style of the broadcaster.
Select Custom to activate
the caption style items and
set your desired detailed
settings.
MENU
ENTER
Channel Menu
1. Press the Menu button.
2. Use the or button to select channel, then
press the button to enter the TV settings.
Channel
3. Use the or button to select the options (air/
cable, auto Scan, auto Scan add ch, channel
Skip, channel no. or channel label). Adjust them
using the or button, or press the button to
go into the detailed settings.
Air
Air/Cable
Auto Scan
Auto Scan Add CH
Channel Skip
Channel No.
Channel Label
DTV Signal
5.1
KTLA-DT
4. Press the Menu button to return to the previous
Good
menu.
5. Repeat steps 3 and 4 to adjust other options.
MENU
ENTER
6. To exit the MAIN MENU and return to the normal
screen, press the Menu button repeatedly.
cable/air
auto Scan
: Cable and Air modes are available.
: Search for available channels and store them in memory.
auto Scan add ch
: Search for more available channels and add them in memory.The channels
previously stored are retained. This is very useful if you find you need to
have antenna in different orientations for reception of particular channels
- and thus wish to perform multiple scans.
channel Skip
channel no.
channel label
DtV Signal
: Skip weak channels and the channels you don’t like.
: Displays currently-selected TV channel.
: display and edit the channel label.
: Display the signal strength (for digital TV channels only).
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
tV SettinG
Channel Skip
1. Use the or button to select a channel. (Press the button to select the last channel of the
page; press again to go to the next page. Press the button to select the first channel of the page;
press again to return to the previous page.)
2. Press the enter button to shift between On / Off. (Select ON to skip the selected channel. The
channel will not appear when you press the ch / ch button.)
Channel Label
you can edit a label for each channel.
1. Use the or button to select the number or letter. Use the or button to move and edit the
next character.
2. After editing, the Channel and Channel label will be shown on the screen when you press the
DiSPlay button.
Maintenance
Cleaning the Unit
• Be sure to turn the unit off and disconnect the AC adapter before maintaining the unit.
• Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth that
has been dipped in a weak soap-and-water solution and wrung out thoroughly. wipe with a dry
cloth.
• Never use alcohol, benzine, thinner, cleaning fluid or other chemicals. Do NOT use compressed
air to remove dust.
As concerns grow about the environmental impact of outdated electronic products,
Venturer Electronics is committed to being
a
part of the solution. Free of charge,
Venturer Electronics customers can return qualifying units to us for recycling.
call 1-800-252-6123.
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
trouBleShootinG GuiDe
SYMPTOM
CAUSE (AND REMEDY)
Unit does not work.
• Unplug the AC power cord and plug it back in.
• Check that the three-way switch is slid to “ON” position.
No picture on the TV
• Choose different channels on the TV set until the picture
screen.
appears.
No sound.
• Make sure the TV sound is not muted.
Remote control does not
work.
• Make sure the batteries are inserted correctly.
• Replace the batteries if they are exhausted.
• Remove any obstacles between the remote control.
• Use the remote near the unit.
• Point the remote at the remote sensor on the unit.
Can not watch a bilingual
TVprograminitssecondary
language.
• Make sure you have correctly selected the appropriate audio
setting (see p. 11). Please note that not all TV stations broadcast a
secondary language.
weak signal or channel not
•
Try to reposition the antenna.
available.
NOTE: Optimal reception of over-the-airTV broadcasts is typically
obtained using an external fixed antenna. Orientation and location
of the antenna is typically critical for best results - if using indoors,
you may find that placement of the antenna near a window, or in
an elevated location, improves performance.
TV can not receive signal
from a connected Cable
box or Satellite box.
• Confirm that a Coaxial cable is connected properly to the TV and
the Cable or Satellite box. Ensure that your Cable or Satellite box
is configured to output a TV signal over a Coaxial cable.
Can I watch TV while
holding the TV, or while
traveling in a vehicle ?
• No - ATSCTV signals can’t be received satisfactorily whileTV is in
motion. The TV and Antenna should be stationary and positioned
for optimal reception. Note: the Car Power Adapter is provided
specifically for “tail-gating” usage.
Specifications and external appearance are subject to change without notice.
need More help?
dO NOT RETURN THIS PROdUCT TO THE STORE
Please visit online help at
Printed in China
811-160791W010
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|