VEC020
™
START- IT Co m p a ct P r o ™
JUMPSTART SYSTEM & POWER SUPPLY
PORTABLE, CORDLESS, RECHARGEABLE 12-VOLT DC POWER SUPPLY
COMPLETELY
PORTABLE,
SAFE AND
CONVENIENT
OWNER’S MANUAL
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE
OF THIS PRODUCT. BEFORE USE, READ AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND
PRODUCT LABELS, PLUS YOUR VEHICLE’S BATTERY MANUFACTURER GUIDELINES. FAILURE TO DO SO COULD RESULT IN
POSSIBLE INJURY OR PROPERTY DAMAGE.
4 1 4 0 S.W. 2 8 TH WAY, FT. LAUDERDALE, FL 3 3 3 1 2
TEL: (9 5 4 ) 5 8 4 -4 4 4 6 • FAX: (9 5 4 ) 5 8 4 -5 5 5 6
w w w .ve cto rm fg .co m
VECTOR MANUFACTURING, Ltd.
4140 S.W. 28th Way
Ft. Lauderdale, FL 33312
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
8. SPECIFICATIONS
WARN IN GS
Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VEC020
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 VDC
Boost Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300 Instantaneous Cranking Amps
Peak Ampere Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .900 Peak Amps
WARN IN G STATEMEN TS IDEN TIFY CO N DITIO N S O R PRACTICES THAT MAY
RESULT IN PERSO N AL IN JURY O R LO SS O F LIFE.
1. When working with lead acid batteries, always make sure immediate assistance is
available in case of accident or emergency.
Battery Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Sealed, high energy density lead-acid,
2. Protective eyewear must be worn when using this product; contact with battery acid may
cause blindness and/ or severe burns; be aware of first aid procedures in case of
accidental contact with battery acid.
rechargeable, maintenance-free,
12 volt DC, 15 Amp-hour
Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 volt 0.2 Amp Krypton
3. There is a risk of explosive gases being released when lead acid batteries are being
charged or discharged. Failure to follow instructions may cause property damage,
explosive hazard, and/ or personal injury.
Booster Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .#6AWG welding cable with
350 Amp copper clamps
Accessory Socket Self-Resetting Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Amps
Charging Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 volt DC
4. Make sure the Safety Switch is Off before connecting battery clamps to discharged
battery. This will enable the polarity alarm to function.
Adapter/ Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110/ 120 Volt AC (500mA,
12 Volt DC Output)
5. When connecting the battery clamps to a discharged battery, and an alarm sounds,
do NOT turn on the Safety Switch - the polarity is reversed. Interchange battery clamps
before turning the Safety Switch ON.
Reverse Polarity Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5 Volts (min)
HEIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.5 in. (21 cm)
DEPTH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.0 in (12.5 cm)
WIDTH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9.8 in(24.5 cm)
WEIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10.7 Lbs (4.84 Kg)
6. When charging unit from a 110/ 120 volt AC electrical outlet in any wet or damp area,
make sure that the outlet used is protected by a Ground Fault Interrupt (GFI) Switch.
7. When charging the unit near water, do not allow the electrical cords and outlets to get
wet or come near water; electrical shock could result!
8. Jumpstart procedures should only be performed in a safe, dry, well-ventilated area.
9. REPLACEMENT PARTS
9. Always store battery clamps in built-in holsters when not in use. Never touch battery
clamps together; this can cause dangerous sparks, power arcing, and/ or explosion.
For replacement parts (bulbs, batteries, fuses, etc.), contact Vector® Customer Service:
(954) 584-4446.
10. When using this unit in proximity to the vehicle’s battery and engine, stand the unit on
a flat, stable surface, and be sure to keep all clamps, cords, clothing and body parts
away from moving vehicle components.
BULB REPLACEMENT
Tools needed - small Phillips screwdriver. Replacement bulbs are available from Vector®
Customer Service Department; call (954) 584-4446 ext. 19.
11. Do not wear vinyl clothing when jumpstarting a vehicle; friction can cause dangerous
static electricity sparks. Remove all jewelry or metal objects that could cause short
circuits or react with battery acid.
1. Unscrew (counterclockwise) and remove two Phillips screws.
2. Remove the lens cover.
12. Always disconnect the negative (Black) jumper cable first; followed by the positive
(Red) jumper cable.
3. Remove the burned-out bulb.
4. Replace with a new bulb (12 volt 0.2 amp Krypton bulb) available from Vector®
Customer Service Department; call (954) 584-4446 ext. 19
13. Never allow red and black clamps to touch each other or another common metal
conductor; this could cause damage to the unit and/ or create sparking/ explosion
hazard. Always store battery clamps in built-in holsters when not in use.
5. Snap the lens cover back into place.
14. Do not expose battery to fire or intense heat as it may explode. Before disposing of
the battery, protect exposed terminals with heavy-duty electrical tape to prevent
shorting (shorting can result in injury or fire).
6. Replace (clockwise) the screws and carefully tighten. Do not over tighten!
15. Do not smoke or use inflammable items (matches, cigarette lighters, etc.) while
working on a vehicle’s battery system.
16. Keep unit out of reach of children (whether stored, or in use).
FIRST AID:
1 . SKIN : If battery acid comes in contact with skin, rinse immediately with water, then
wash thoroughly with soap and water. If redness, pain, or irritation occurs,
seek immediate medical attention.
2 . EYES: If battery acid comes in contact with eyes, flush eyes immediately for a minimum
of 15 minutes; seek immediate medical attention.
1 4
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS
5 .2 ESTIMATED 1 2 VO LT DC USAGE TIMES
CAUTIO N STATEMEN TS ADVISE AGAIN ST CERTAIN CO N DITIO N S AN D
PRACTICES THAT MAY RESULT IN DAMAGE TO VEHICLES, APPLIAN CES,
AN D/ O R THE START-IT Co m p a ct Pro ™ JUMPSTART SYSTEM.
Table II shows the estimated 12 volt DC operation times when using a fully
charged system.
Table II - START-IT Co m p a ct Pro ™ as a 12 Volt DC Power Supply
1. IMPO RTAN T: Although this unit is delivered in a partially-charged state, you must fully
charge it with the supplied 110/ 120 volt AC charger for a full 24 hours before using
it for the first time. You cannot overcharge the unit using the AC charger method.
APPLIANCE TYPE
ESTIMATED POWER
CONSUMPTION (IN WATTS)
ESTIMATED USAGE
TIME (IN HOURS)
2. Use only the supplied cords/ adapters for recharging this unit. Do not recharge for more
than 3-4 hours maximum using 12 volt DC method. Recharge unit after each use.
CELL PHONE
>1
8-15
9
30-80 hrs. Talk Time
3. All On/ Off switches should be in the OFF position when the unit is charging or not in
use. Make sure all switches are in the OFF position before connecting to a power source
or load.
FLUORESCENT LIGHT
RADIO, FAN, DEPTH FINDER
CAMCORDER, VCR
15
14
8
15
24
48
4. Never insert a nything other tha n the supplied power/ recha rging cords or
recommended appliance power/ recharging cords into the 12 volt DC charging/ power
socket on this unit. Do not use any accessory that is not recommended or provided by
the manufacturer.
POWER TOOLS, BILGE PUMP
ELECTRIC COOLER
5
3
AIR COMPRESSOR, CAR VACUUM
SPOTLIGHT
80
1.0
9 hrs.
5. Do not use this unit to operate appliances that draw more than 20 amps.
100
6. This system is designed to be used only on vehicles with 12 volt DC battery systems.
Do not connect to a 6 volt or 24 volt battery system.
NOTE:ALL TIMES ARE APPROXIMATE, AND BASED UPON FULLY CHARGED UNIT.
7. This system is not designed to be used as a replacement for a vehicular battery. Do not
attempt to operate a vehicle that does not have a battery installed.
6. EMERGENCY/ WORK LIGHT
The Emergency/ Work light (Figure 1) is controlled by it’s On/ Off switch. Make sure the
lamp is turned Off when the unit is being recharged or stored.
7. BATTERY REPLACEMENT
8. Vehicles that have on-board computerized systems may be damaged if vehicle battery
is jumpstarted. Before jumpstarting, read the vehicle’s owner’s manual to confirm that
external starting assistance is advised.
It is recommended that the unit be returned to Vector® Customer Service for battery
replacement: Contact (954) 584-4446 ext. 19.
9. Excessive engine cranking can damage a vehicle’s starter motor. If the engine fails to
start after the recommended number of attempts, discontinue jumpstart procedures and
look for other problems that may need to be corrected.
7 .1 BATTERY DISPO SAL:
10. Although this unit contains a non-spillable battery, it is recommended that unit be
kept upright during storage, use and recharging. To avoid possible damage that
may shorten the unit’s working life, protect it from direct sunlight, direct heat,
and/ or moisture.
THIS UNIT CONTAINS A MAINTENANCE-FREE, SEALED, NON-SPILLABLE,
LEAD ACID BATTERY WHICH MUST BE DISPOSED OF PROPERLY. ALL
STATES REQ UIRE RECYCLING. DISPO SAL Q UESTIO NS? IN USA,
CALL 1-877-288-7722.
11. Check unit periodically for wear and tear. Replace worn or defective parts immediate-
ly. Contact Vector® customer service department at (954) 584-4446.
WARN IN GS:
•
•
DO N O T DISPO SE O F THE BATTERY IN FIRE AS THIS MAY RESULT IN AN EXPLO SIO N .
BEFO RE DISPO SIN G O F THE BATTERY, PRO TECT EXPO SED TERMIN ALS W ITH HEAVY-DUTY
ELECTRICAL TAPE TO PREVEN T SHO RTIN G (SHO RTIN G CAN RESULT IN IN JURY O R FIRE)
DO N O T EXPO SE BATTERY TO FIRE O R IN TEN SE HEAT AS IT MAY EXPLO DE
12. Do not attempt to jumpstart a frozen battery.
13. Never submerge this unit in water.
•
4
1 3
Download from Www.Somanuals.com. All Manuals Search And Download.
4 .3 ESTIMATED BATTERY LIFE
CONTENTS
Table I shows the relationship of the frequency of use between recharging and the
expected number of discharge/ recharge cycles
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2. SWITCHES, INDICATORS, PORTS . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Table I - Estimated Battery Life
AVERAGE NUMBER OF USES
(JUMPSTART OR DISCHARGES)
BETWEEN RECHARGES
POTENTIAL TOTAL NUMBER
OF JUMPSTART OR DISCHARGE CYCLES
(LIFETIME OF UNIT BATTERY)
3. USING START-IT COMPACT PRO™ AS A JUMPSTART SYSTEM` . . . . . . .8
3.1 Easy, Step-by-Step Jumpstarting Instructions . . . . . . . . . . . . . . . . . . . . . . . . .9
1 . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000+
5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .700+
10 . . . . . . . . . . . . . . . . . . . . . . . . . . . .500+
4. CHARGING/ RECHARGING
4.1 110/ 120-Volt AC Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.2 12 Volt DC Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.3 Estimated Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
5. OPERATION AS A 12 VOLT PORTABLE POWER SUPPLY
N O TE: Make sure that the unit‘s Safety ON/ OFF switch is ALWAYS in the OFF position
when using the 12 volt DC accessory outlet.
5. OPERATING AS A PORTABLE POWER SUPPLY
1. Lift up the cover of the unit‘s 12 volt DC cigarette lighter-type accessory receptacle
(See Figure 1).
5.1 Operating as a 12 Volt DC Power Supply . . . . . . . . . . . . . . . . . . . . . . . .12
5.2 Estimated 12 Volt DC Usage Times . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2. Insert the 12 volt DC plug from the appliance into the receptacle on the unit.
3. Switch on the appliance, and operate as usual.
6. EMERGENCY/ WORK LIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
CAUTIO N : DO N O T USE THIS UN IT TO O PERATE APPLIAN CES THAT DRAW
7. BATTERY REPLACEMENT
MO RE THAN 2 0 AMPS.
7.1 Battery Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
8. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
9. REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
WARRANTY
One Year Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
1 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4. CHARGING/ RECHARGING
For maximum battery life, we recommend that the START-IT Co m p a ct Pro ™ system
be kept fully charged at all times. If the battery is allowed to remain in a discharged
state, battery life will be shortened. Note: Recharging battery after each use will
prolong battery life; frequent discharges between recharges will reduce battery life.
FIGURE 1
2
4
1. 12 Volt DC Accessory Socket,
with 20 amp overload protection
11
1 2
1
3
10
4 .1 1 1 0 / 1 2 0 VO LT AC CHARGIN G
2. Safety ON/OFF Power Switch
(No Key Required)
IMPO RTAN T:
• MAKE SURE ALL SWITCHES ARE TURNED OFF DURING RECHARGING
• Charge unit for full 24 hours, prior to first use
• Recharge unit fully after each use
3. Charge Status Push Button
7
4. LED Charging/Battery Status Indicators
5. Heavy-Duty #6AWG Welding Quality
Jumper Cables
5
• Recharge unit every two months, when it has not been used
8
6. Heavy Duty, 350 Amp Copper Clamps
7. Exclusive, Quick-Release, Clamp Holsters
1. Simply plug the 110/ 120 volt AC plug of the AC/ DC adapter/ charger cord into any
standard 110/ 120 volt AC wall outlet.
2. Plug the barrel connector attached to the AC/ DC adapter cord into the small barrel
receptacle on the jumpstarter.
9
8. 110/120 Volt UL approved AC/DC
Charging Adapter Cord
9. 12 Volt DC/DC Charging Adapter Cord
10. Built-in Emergency Work light
11. Light ON/OFF Switch
3. Charge this device for at least 14-24 hours or until the FULL indicator lights.
4. When charging is completed and the green FULL light lights or blinks, remove the
charging adapter and store in a safe place.
6
5. N O TE: The unit CANNOT be overcharged using the AC method.
12. AC Recharge Adapter barrel
connector receptacle
12-Volt DC
Charging Cord
110/120-Volt AC
Adapter/Charger
ADDITIONAL FEATURES
Barrel
Connector
• Easy-to-use: EMERGEN CY JUMPSTARTER for cars, light trucks, jet skis, snowmobiles,
farm equipment, boats, SUVs and RVs, garden tractors, gasoline engine generators
(almost any 12 volt battery system)
• Provides Instant 1 2 VO LT DC PO W ER - whenever, and wherever it’s needed
• Ideal for farm/ ranch, home, tailgate parties, beach, picnic, campsite, wilderness,
utility power outages, emergency repair, etc.
4 .2 1 2 VO LT DC CHARGIN G
The START-IT Co m p a ctPro ™ system also comes with a DC/ DC charging cord, for
recharging the unit from a 12 volt DC cigarette lighter socket in a vehicle or boat. Note:
This recharging method will NOT recharge the unit as effectively as recharging from a
110/ 120 volt AC outlet. The 12 volt DC recharging procedure is recommended only
when it is necessary, as continued use of the 12 volt DC recharging procedure may
shorten the life of the battery.
• Includes non-spillable, maintenance-free, heavy-duty, new high energy density
15 amp hour sealed battery
• Sturdy and unique compact design provides up to 35 hours of completely portable
12 volt DC power
• Sa fe to use, transport, and store
WARN IN G: DO N O T RECHARGE FO R MO RE THAN 3 -4 HO URS MAXIMUM
USIN G 1 2 VO LT DC METHO D. N EVER LEAVE UN IT UN ATTEN DED
IN VEHICLE W HILE DC CHARGIN G
• Requires no maintenance (other than recharging) for optimum operation
• Automatic taper charge for AC recharge
1. NOTE: If unit is fully discharged, it is recommended that the vehicle being used for
recharging be left running while the unit is being charged via the 12 volt DC method.
• Audible alarm for reverse polarity
• Molded high-impact case is tough and durable
• Easy-to-read LED battery charging/ status indicators
2. Insert one end of the DC/ DC charging cord into the 12 volt DC cigarette lighter
receptacle on the vehicle or boat.
3. Insert the plug at the other end of this power cord into the 12 volt DC receptacle on
the front panel of the unit.
• Built-in halogen work/ emergency light with ultra-bright krypton bulb for roadside
repairs and use in remote locations without utility power
4. Charge the unit until the green FULL indicator lights when Charge Status Push Button
is pressed. DO NOT EXCEED 3-4 HOURS MAXIMUM.
5. When charging is completed, remove the power cord and store in a safe place.
6
1 1
Download from Www.Somanuals.com. All Manuals Search And Download.
1. INTRODUCTION:
POSITIVE GROUND SYSTEMS (UNCOMMON)
Congratulations on selecting the Vector® START-IT Co m p a ct Pro ™ JUMPSTART
SYSTEM & 1 2 VO LT DC PO W ER SUPPLY. This compact jumpstarter is unique in the
amount of energy it can supply for it’s size. The internal battery is a Vector® developed
high density sealed lead acid battery that stores and delivers energy comparable to full
sized ordinary jumpstarters. Please read this guide carefully before use to ensure
optimum performance and avoid damage to the unit or to items with which you are
using the jumpstater.
The Vector® START-IT Co m p a ct Pro ™ JUMPSTART SYSTEM & 1 2 VO LT DC
PO W ER SUPPLY is a compact, durable and portable jumpstart system for vehicles
and boats that have a standard 12 volt battery system. This self-contained, rechargeable
system will start most vehicles and boats without the need for a host vehicle or
110/ 120-volt AC power supply.
N O TE: In the rare event that the vehicle to be started has a Positive Grounded
System (positive battery terminal is connected to chassis): Replace step
4 and 5 above with steps, 4a and 5a and then proceed to steps 6
through 8 below.
4a. Connect negative (-) black clamp to vehicle battery‘s negative terminal.
5a. Connect positive (+) red clamp to vehicle chassis or a solid, non-moving,
metal vehicle component or body part. DO NOT clamp directly to positive
battery terminal or moving part.
6. Turn jumpstart system‘s power switch to O N position.
7. Start vehicle (do not turn key for longer than 5-6 seconds).
It can also be used as a safe, portable source of 12 volt DC electric power in remote
locations and/ or emergency situations. It is ideal for use with Vector® 12-volt DC cordless,
8. After vehicle starts, turn jumpstart system‘s Safety Switch to O FF position. Remove
clamps (disconnect the negative (Black) jumper cable first; followed by the positive
(Red) jumper cable) and replace them in the built-in storage holsters. Squeeze the
handles and slide the clamp into position and release your grip.
®
portable, rechargeable products and MAXX DC/ AC Power Inverters. Use the START-IT
Co m p a ct Pro ™ to:
- Ju m p sta rt:
Any engine system with a standard 12 volt DC battery: boat, truck, car, RV, personal
watercraft, snowmobile, garden tractor, gasoline engine generator, etc.
CAUTIO N S:
• If engine fails to start, leave ignition key turned off, make sure safety switch is off and
disconnect the negative (–) clamp first, then the positive (+) clamp. Try again later; the
engine may be flooded.
- O p e ra te : 1 2 vo lt DC:
Fans, inflators, fluorescent work lights, cellular phones*, air compressors, inflators,
spotlights, TVs, portable radios, cassette or CD players and more. *Can quick charge
a cellular phone by using the phone’s 12 volt DC adapter cord.
• Recharge jumpstart system after each use.
- O p e ra te : Ce rta in 1 1 0 / 1 2 0 vo lt AC Acce sso rie s (re q u ire s a Ve cto r 1 2 vo lt
p o w e r in ve rte r, so ld se p a ra te ly )
WARN IN GS:
• Always disconnect the negative (black) jumper cable first; followed by the positive
(red) jumper cable.
2. SWITCHES, INDICATORS AND PORTS:
The Safety Power Switch (Figure 1) is located on the upper left side of the panel.When it is
in the OFF position, the cable clamps are not powered and the reverse polarity alarm is
enabled and ready to detect polarity.
• Never allow red and black clamps to touch each other or another common metal
conductor; this could cause damage to the unit and/ or create sparking/ explosion
hazard.
Below the Safety Power Switch is an On/ Off rocker switch (Figure 1) for the Worklight. The
Worklight is powered when the On/ Off rocker switch is On. The Worklight provides the
user with light while changing a tire, and connecting battery clamps. The Worklight is
• There is a risk of explosive gases being released when batteries are improperly
charged or discharged. Failure to follow instructions may cause property damage,
explosive hazard, and/ or personal injury.
a
long lasting lamp and will continuously operate for three days from a fully
charged battery.
• Always use protective eyewear when using this product; contact with battery
acid may cause blindness and/ or severe burns.
To the right of the rocker switch is the AC Recharge port (Figure 1). It is covered by a
rubber cap that keeps dust, dirt, and moisture out of the socket. The AC Recharge Adapter’s
barrel connector plugs into this port during recharge. Moving to the right are three LEDs, a
Battery Status Display, and a pushbutton. Pressing the pushbutton turns on the Battery Status
Display. Press the pushbutton to check the battery level at any time. Also press it
periodically during DC recharge.
• Keep out of reach of children.
• ALWAYS store battery clamps in built-in holsters when not in use. Never touch battery
clamps together; this can cause dangerous sparks, power arcing and/ or explosion.
The colors of the three LEDs are two red and one green. During AC recharge, the Battery
Status Display is active to indicate the level of charge on the battery. The leftmost red LED
indicates minimum charge on the battery. Recharge the battery when that LED is the only
one lit. The center red LED indicates moderate charge on the battery. The green LED on the
right indicates when the battery is FULL and you can stop charging.
FIRST AID:
• Sk in : If battery acid comes in contact with skin, rinse immediately with water, then
wash thoroughly with soap and water. If redness, pain, or irritation occurs, seek
immediate medical attention.
Below the Battery Status Display is a 12 Volt Accessory Socket (Figure 1). It is covered with
a rubber protective cap. The cap keeps dust, dirt and moisture out of the socket. When the
cap is lifted, the accessory socket can be used for powering 12 volt appliances that draw
up to 20 amps current. This socket is also used during DC recharge.
7
• Ey e s: If battery acid comes in contact with eyes, flush eyes immediately, for minimum
of 15 minutes. SEEK IMMEDIATE MEDICAL ATTENTION.
1 0
Download from Www.Somanuals.com. All Manuals Search And Download.
• DO NOT smoke or use inflammable items (matches, cigarette lighters, etc.) while
working on a vehicle’s battery system
Fig u re 1
Safety Switch
Red LEDs
• When using this jumpstarter in proximity to the vehicle‘s battery and engine, stand the
unit on a flat, stable surface, and be sure to keep all cords and cables well away from
any moving parts
Full Green LED
Battery Status Pushbutton
Positive Battery
Clamp
• Check unit periodically for wear and tear. Replace worn or defective parts immediately
- contact Vector® Customer Service Department at (954) 584-4446 ext. 19 or through
Negative Battery
Clamp
Worklight
ON/OFF
Switch
• Do not attempt to jumpstart a frozen battery
• NEVER submerge this unit in water
12 Volt Accessory Socket (DC Recharge)
• Do not wear vinyl clothing when jumpstarting a vehicle; friction can cause dangerous
static electricity sparks. Remove all jewelry or metal objects; they can cause short cir-
cuits or react with battery acid to cause severe burns. Remove or secure any loose
clothing items and restrain long hair, before attempting jumpstart procedure
Worklight
AC/DC Recharge Port
WARN IN G: Automotive lead-acid batteries can generate hydrogen gas during normal
operation. More gas is generated when the battery is charging. Hydrogen
gas is: • Explosive • Poisonous to Breathe • Highly Flammable
CAUTIO N S:
• Vehicles that have on-board computerized systems may be damaged if vehicle battery
is jumpstarted. Before jumpstarting this type of vehicle, read the vehicle’s owner’s
manual to confirm that external starting assistance is advised.
• Excessive engine cranking can damage the vehicle‘s starter motor. If the engine fails
to start after the recommended number of attempts, discontinue jumpstart procedure
and look for other problems that may need to be corrected.
To avoid an explosion and/ or the possibility of being splashed with battery acid:
• NEVER allow the red and black clamps to touch each other or a common metal object
• ONLY attempt to jumpstart a vehicle, boat or engine system in a WELL ventilated area
• ALWAYS CONNECT THE RED (+) CLAMP TO THE POSITIVE (+) BATTERY
TERMINAL FIRST
• DO NOT CONNECT THE BLACK (–) CLAMP TO THE NEGATIVE (–) BATTERY
TERMINAL
3 .1 EASY, STEP-BY-STEP JUMPSTARTIN G IN STRUCTIO N S
1. Turn OFF vehicle ignition and all accessories (radio, a/ c, lights, cell phone, etc.).
Place vehicle in “park” and set the emergency brake.
• DO CONNECT THE BLACK (–) CLAMP TO A NON-MOVING METAL PART ON
THE ENGINE
CAUTIO N S:
2. Make sure jumpstart system’s Safety Switch is turned OFF.
I. To avoid possible damage that may shorten the unit’s working life, protect this unit
from direct sunlight, direct heat, and/ or moisture.
3. Remove the booster clamps from protective holster (fig. 2): simply squeeze the handles
and pull down on the clamp.
2. This system is to be used ONLY on vehicles, boats, garden tractors and gasoline
powered generators with 12 volt DC battery systems.
Fig u re 2
Follow procedure for negative or positive
grounded system, as follows:
N EGATIVE GRO UN DED SYSTEM
(NEGATIVE BATTERY TERMINAL IS
CONNECTED TO CHASSIS MO ST
CO MMO N METHO D
3. This system is NOT designed to be installed as a replacement for a vehicular battery.
RECO MMEN DATIO N S FO R O PTIMUM PERFO RMAN CE O F THE START-IT
Co m p a ct Pro ™ JUMPSTART SYSTEM:
WARN IN G: Never insert anything other than the supplied power/ recharging cords or
recommended appliance power/ recharging cords into the charging or
power receptacles on this unit.
IMPO RTAN T: Th e Sa fe ty O N / O FF Sw itch sh o u ld b e in th e O FF p o sitio n
w h e n th e u n it is ch a rg in g , o r n o t in u se .
Clamp
Handle
3. USING THE START-IT Compact Pro™ AS A JUMPSTART SYSTEM
SLIDE DOWN AND ROTATE CLAMP OUTWARD
FROM SIDE OF UNIT TO REMOVE
WARN IN GS:
4. Connect positive (+) red clamp to vehicle battery‘s positive terminal.
1. Before using this system to jump start any vehicle or boat, read and understand all
instructions, safety tips, warnings and cautions and first aid information provided in
this manual and on the product labeling. Additional important information may also
be provided by the vehicle‘s battery system manufacturer.
5. Connect negative (-) black clamp to chassis or a solid, non-moving, metal vehicle
component or body part. Never clamp directly to negative battery terminal or moving
part. If the audible alarm sounds, the polarity is not correct. Reverse the connections.
DO N O T TURN O N THE SAFETY SW ITCH W ITH ALARM SO UN DIN G.
2. Be aware of first aid procedures before attempting jumpstart procedure.
3. ALWAYS wear protective eyewear when working with a lead acid-type battery.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
|